ZBT WE-826
- Supported Versions
- Hardware Highlights
- Installation
- Hardware
  - Info
  - Photos
  - Opening the case
  - Serial
- Debricking
  - HTTP method
  - UBOOT Method
- Bootlogs
  - OpenWrt bootlog
- Notes
- Tags

ZBT WE-826

There are 2 variants of this router:

WE-826-B green leds, a plastic case, bgn/an/ac
WE-826-T blue leds, metal case, and a populated serial header, and a user accessible sim slot, bgn only.

Supported Versions

Hardware Highlights

Installation

The official manual on how to flash the WE-826 series is available >here<

Installation using the webinterface:

Plug a computer to any lan port of the device.
Hold the reset button.
Power on the device while holding the reset button for at least 15 seconds.
Set you computers ipv4 settings to 192.168.1.2 for the ip, and 255.255.255.0 for the subnet mask.
Open 192.168.1.1 in your web browser and upload your firmware using the webinterface.
Do not disconnect the device now! Doing so could eventually brick it.
Wait 90 Seconds for the device to finish the flashing procedure, it will automatically restart.
You can now reload the web page and start configuring OpenWrt.

Hardware

Info

Architecture	MIPS
Vendor	MediaTek (Ralink)
System-On-Chip	Mediatek MT7620A ver:2 eco:6
CPU	MIPS 24KEc V5.0
CPU Speed	580 MHz
Flash	16 MB Winbond 25Q128
RAM	128 MB
Wireless	SoC
Ethernet	10/100
USB	Yes 1x (EHCI,OHCI)
SD	Yes 1x
e-PCI	Yes 1x
SIM-slot	Yes 1x (accessible from inside only - connected to e-PCI)
Serial	Yes

Photos

WikiDevi page with additional info and internal board photos

https://wikidevi.com/wiki/ZBT_WE826

Photos and other information from seller: ( I didn't have enough rights for adding pictures )

Sales article at aliexpress.com

Another link with similar information:

Sales article at aliexpress.com

Opening the case

Unscrew two screws from the bottom of the device, another one is under tape.
Pray it open carefully.

Serial

There is a serial header available on this board, labeled J2, with the following pinout:

Pin	Designation
1	VCC - DO NOT CONNECT
2	RX
3	TX
4	GND

Serial connection parameters	115200 8N1

https://i.imgur.com/2CleBoY.jpg

Once you are on the console, it is possible to control the UBoot bootloader.

Please choose the operation:                                                    
   1: Load system code to SDRAM via TFTP.                                       
   2: Load system code then write to Flash via TFTP.                            
   3: Boot system code via Flash (default).                                     
   4: Entr boot command line interface.                                         
   7: Load Boot Loader code then write to Flash via Serial.                     
   9: Load Boot Loader code then write to Flash via TFTP.                       
 0                                                                                                                                              
3: System Boot system code via Flash.

To engage any of those options hold that key down while applying power. Note the default is “3”.

Debricking

HTTP method

Disconnect power
Set your computer's IP address to 192.168.1.22 or something else in that network except 192.168.1.1
Connect power and after lights have changed the first time, hold down reset button (don't know how long it needs)
And try to open 192.168.1.1 with your browser. (You might need to clear cache first)
You might find this easier, by pinging 192.168.1.1 first continuously.
After page opens, you may release reset button. Use web-interface which opened to browser to upload new image.

UBOOT Method

connect a serial port (requires soldering)
setup a TFTP server
apply power to the board, choose “2: Load system code then write to Flash via TFTP.” by holding the 2 key down as power is applied.
Enter the routers IP address at the “Input device IP” prompt.
Enter the TFTP server IP address at the “Input server IP” prompt.
Enter the image name you wish to load at the “Input Linux Kernel filename” prompt. Sysupgrade format worked for me, which is more than just a kernel.

It will look like this:

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 

You choosed 2

 0 

   
2: System Load Linux Kernel then write to Flash via TFTP. 
 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.1.1) ==:192.168.1.1
        Input server IP (192.168.1.222) ==:192.168.1.222
        Input Linux Kernel filename (openwrt-ramips-mt7620-uImage.bin) ==:openwrt-ramips-mt7620-zbt-we826-squashfs-sysupgrade.bin

Bootlogs

OpenWrt bootlog

Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.000000] Linux version 3.18.16 (osku@alarm64) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46133) ) #4 Sun Jun 28 14:49:42 EEST 2015 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Board has DDR2 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Analog PMU set to hw control Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Digital PMU set to hw control Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] bootconsole [early0] enabled Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] MIPS: machine is ZBT WE-826 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Determined physical RAM map: Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] memory: 08000000 @ 00000000 (usable) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Zone ranges: Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Movable zone start for each node Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Early memory node ranges Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] On node 0 totalpages: 32768 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 803141b0, node_mem_map 810090e0 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] Normal zone: 256 pages used for memmap Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Writing ErrCtl register=00029cb0 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] Readback ErrCtl register=00029cb0 Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.000000] Memory: 126272K/131072K available (2592K kernel code, 129K rwdata, 524K rodata, 136K init, 186K bss, 4800K reserved) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] NR_IRQS:256 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] CPU Clock: 580MHz Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.000000] systick: running - mult: 214748, shift: 32 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.050000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.060000] pid_max: default: 32768 minimum: 301 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.070000] pinctrl core: initialized pinctrl subsystem Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.080000] NET: Registered protocol family 16 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: try to register 73 pins ... Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] pinctrl core: add 3 pinmux maps Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: found group selector 0 for i2c Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: found group selector 7 for spi refclk Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: found group selector 11 for wled Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: request pin 37 (io37) for pinctrl Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: request pin 38 (io38) for pinctrl Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: request pin 39 (io39) for pinctrl Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: request pin 72 (io72) for pinctrl Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.090000] rt2880-pinmux pinctrl: failed to lookup the sleep state Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.100000] rt2880_gpio 10000600.gpio: registering 24 gpios Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.110000] rt2880_gpio 10000600.gpio: registering 24 irq handlers Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.110000] rt2880_gpio 10000638.gpio: registering 16 gpios Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.120000] rt2880_gpio 10000638.gpio: registering 16 irq handlers Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.120000] rt2880_gpio 10000688.gpio: registering 1 gpios Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.130000] rt2880_gpio 10000688.gpio: registering 1 irq handlers Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.130000] Switched to clocksource systick Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.140000] NET: Registered protocol family 2 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.140000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.140000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.150000] TCP: Hash tables configured (established 1024 bind 1024) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.160000] TCP: reno registered Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.160000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.170000] NET: Registered protocol family 1 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.170000] PCI: CLS 0 bytes, default 32 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.180000] rt-timer 10000100.timer: maximum frequency is 2441Hz Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.180000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.180000] futex hash table entries: 256 (order: -1, 3072 bytes) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.200000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.210000] msgmni has been set to 246 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.220000] io scheduler noop registered Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.220000] io scheduler deadline registered (default) Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.230000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[147] Sun Jun 28 16:05:42 2015 kern.warn kernel: [ 0.230000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[161] Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.240000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.240000] serial8250 serial8250: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.250000] pinctrl core: add 1 pinmux maps Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.250000] rt2880-pinmux pinctrl: found group selector 3 for uartlite Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.250000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.250000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.250000] console [ttyS0] disabled Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.250000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.260000] console [ttyS0] enabled Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.260000] bootconsole [early0] disabled Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.270000] pinctrl core: add 1 pinmux maps Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.270000] rt2880-pinmux pinctrl: found group selector 2 for spi Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.270000] rt2880-pinmux pinctrl: request pin 3 (io3) for 10000b00.spi Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.270000] rt2880-pinmux pinctrl: request pin 4 (io4) for 10000b00.spi Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.270000] rt2880-pinmux pinctrl: request pin 5 (io5) for 10000b00.spi Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 0.270000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.290000] m25p80 spi32766.0: w25q128 (16384 Kbytes) Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.290000] 4 ofpart partitions found on MTD device spi32766.0 Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.300000] Creating 4 MTD partitions on "spi32766.0": Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.310000] 0x000000000000-0x000000030000 : "u-boot" Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.310000] 0x000000030000-0x000000040000 : "u-boot-env" Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.320000] 0x000000040000-0x000000050000 : "factory" Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.320000] 0x000000050000-0x000001000000 : "firmware" Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.450000] 2 uimage-fw partitions found on MTD device firmware Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.460000] 0x000000050000-0x00000016d999 : "kernel" Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.470000] 0x00000016d999-0x000001000000 : "rootfs" Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.470000] mtd: device 5 (rootfs) set to be root filesystem Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.480000] 1 squashfs-split partitions found on MTD device rootfs Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 0.490000] 0x000000770000-0x000001000000 : "rootfs_data" Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.490000] gsw: setting port4 to ephy mode Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.500000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.510000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.520000] rt2880_wdt 10000120.watchdog: Initialized Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.520000] TCP: cubic registered Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.520000] NET: Registered protocol family 17 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.530000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.540000] 8021q: 802.1Q VLAN Support v1.8 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.570000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.570000] Freeing unused kernel memory: 136K (8032e000 - 80350000) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 0.580000] ralink_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex) Sun Jun 28 16:05:42 2015 user.info kernel: [ 3.040000] init: Console is alive Sun Jun 28 16:05:42 2015 user.info kernel: [ 3.040000] init: - watchdog - Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.240000] usbcore: registered new interface driver usbfs Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.250000] usbcore: registered new interface driver hub Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.250000] usbcore: registered new device driver usb Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.260000] rt2880-pinmux pinctrl: request pin 1 (io1) for pio:1 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.260000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.270000] ehci-platform: EHCI generic platform driver Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.480000] phy phy-usbphy.0: remote usb device wakeup disabled Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.480000] phy phy-usbphy.0: UTMI 16bit 30MHz Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.490000] ehci-platform 101c0000.ehci: EHCI Host Controller Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.490000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.500000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.530000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.530000] usb usb1: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.530000] hub 1-0:1.0: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.530000] hub 1-0:1.0: USB hub found Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.540000] hub 1-0:1.0: 1 port detected Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.540000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.550000] ohci-platform: OHCI generic platform driver Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.560000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.560000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.570000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.640000] usb usb2: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.640000] hub 2-0:1.0: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.640000] hub 2-0:1.0: USB hub found Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.640000] hub 2-0:1.0: 1 port detected Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.650000] rt2880-pinmux pinctrl: request pin 38 (io38) for pio:38 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.650000] rt2880-pinmux pinctrl: request pin 39 (io39) for pio:39 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 6.650000] rt2880-pinmux pinctrl: request pin 72 (io72) for pio:72 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 6.870000] usb 1-1: new high-speed USB device number 2 using ehci-platform Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 7.020000] usb 1-1: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 7.020000] hub 1-1:1.0: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 7.020000] hub 1-1:1.0: USB hub found Sun Jun 28 16:05:42 2015 kern.info kernel: [ 7.020000] hub 1-1:1.0: 4 ports detected Sun Jun 28 16:05:42 2015 user.info kernel: [ 7.070000] init: - preinit - Sun Jun 28 16:05:42 2015 kern.info kernel: [ 7.520000] usb 1-1.2: new high-speed USB device number 3 using ehci-platform Sun Jun 28 16:05:42 2015 kern.info kernel: [ 7.880000] 8021q: adding VLAN 0 to HW filter on device eth0 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 7.900000] usb 1-1.2: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 7.900000] random: procd urandom read with 14 bits of entropy available Sun Jun 28 16:05:42 2015 kern.notice kernel: [ 11.380000] jffs2: notice: (313) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. Sun Jun 28 16:05:42 2015 user.info kernel: [ 11.400000] mount_root: switching to jffs2 overlay Sun Jun 28 16:05:42 2015 user.info kernel: [ 11.440000] procd: - early - Sun Jun 28 16:05:42 2015 user.info kernel: [ 11.440000] procd: - watchdog - Sun Jun 28 16:05:42 2015 user.info kernel: [ 12.220000] procd: - ubus - Sun Jun 28 16:05:42 2015 user.info kernel: [ 13.410000] procd: - init - Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.880000] NET: Registered protocol family 38 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.920000] NET: Registered protocol family 10 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.930000] Initializing XFRM netlink socket Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.940000] NET: Registered protocol family 15 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.940000] tun: Universal TUN/TAP device driver, 1.6 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.950000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Sun Jun 28 16:05:42 2015 kern.info kernel: [ 14.990000] ip6_tables: (C) 2000-2006 Netfilter Core Team Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.020000] u32 classifier Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.030000] input device check on Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.030000] Actions configured Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.050000] Mirror/redirect action on Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.070000] nf_conntrack version 0.5.0 (1975 buckets, 7900 max) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.090000] usbcore: registered new interface driver cdc_wdm Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.100000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.110000] Backport generated by backports.git backports-20150129-0-gdd4a670 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.130000] ip_tables: (C) 2000-2006 Netfilter Core Team Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.180000] usbcore: registered new interface driver usbserial Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.190000] usbcore: registered new interface driver usbserial_generic Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.190000] usbserial: USB Serial support registered for generic Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.260000] xt_time: kernel timezone is -0000 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.270000] cdc_ether 1-1.2:1.0: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.280000] cdc_ether 1-1.2:1.0 eth1: register 'cdc_ether' at usb-101c0000.ehci-1.2, CDC Ethernet Device, 00:1e:10:1f:00:00 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.300000] usbcore: registered new interface driver cdc_ether Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.320000] usbcore: registered new interface driver cdc_ncm Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.380000] cfg80211: Calling CRDA to update world regulatory domain Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.410000] cfg80211: World regulatory domain updated: Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.410000] cfg80211: DFS Master region: unset Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.410000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.420000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.430000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.440000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.470000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.480000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.480000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.500000] usbcore: registered new interface driver huawei_cdc_ncm Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.560000] PPP generic driver version 2.4.2 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.570000] NET: Registered protocol family 24 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.600000] usbcore: registered new interface driver option Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.600000] usbserial: USB Serial support registered for GSM modem (1-port) Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.610000] option 1-1.2:1.2: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.610000] option 1-1.2:1.2: GSM modem (1-port) converter detected Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.620000] option1 ttyUSB0: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.620000] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.620000] option 1-1.2:1.3: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.630000] option 1-1.2:1.3: GSM modem (1-port) converter detected Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.630000] option1 ttyUSB1: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.630000] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1 Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.640000] option 1-1.2:1.4: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.640000] option 1-1.2:1.4: GSM modem (1-port) converter detected Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.650000] option1 ttyUSB2: no of_node; not parsing pinctrl DT Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.650000] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2 Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.700000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected Sun Jun 28 16:05:42 2015 kern.info kernel: [ 15.700000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected Sun Jun 28 16:05:42 2015 kern.debug kernel: [ 15.710000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' Sun Jun 28 16:05:45 2015 authpriv.info dropbear[1116]: Not backgrounding Sun Jun 28 16:05:48 2015 user.emerg : Starting strongSwan 5.3.2 IPsec [starter]... Sun Jun 28 16:05:48 2015 authpriv.info ipsec_starter[1168]: Starting strongSwan 5.3.2 IPsec [starter]... Sun Jun 28 16:05:48 2015 daemon.err modprobe: ah4 is already loaded Sun Jun 28 16:05:48 2015 daemon.err modprobe: esp4 is already loaded Sun Jun 28 16:05:48 2015 daemon.err modprobe: ipcomp is already loaded Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.560000] 8021q: adding VLAN 0 to HW filter on device eth0 Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.590000] device eth0.1 entered promiscuous mode Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.600000] device eth0 entered promiscuous mode Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.620000] br-lan: port 1(eth0.1) entered forwarding state Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.620000] br-lan: port 1(eth0.1) entered forwarding state Sun Jun 28 16:05:48 2015 daemon.err modprobe: xfrm4_tunnel is already loaded Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'lan' is enabled Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'lan' is setting up now Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'lan' is now up Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.690000] device eth0.2 entered promiscuous mode Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.690000] br-lan: port 2(eth0.2) entered forwarding state Sun Jun 28 16:05:48 2015 kern.info kernel: [ 24.700000] br-lan: port 2(eth0.2) entered forwarding state Sun Jun 28 16:05:48 2015 daemon.err modprobe: xfrm_user is already loaded Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'loopback' is enabled Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'loopback' is setting up now Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'loopback' is now up Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'wan' is setting up now Sun Jun 28 16:05:48 2015 daemon.notice netifd: Bridge 'br-lan' link is up Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'lan' has link connectivity Sun Jun 28 16:05:48 2015 daemon.notice netifd: Network device 'eth0' link is up Sun Jun 28 16:05:48 2015 daemon.notice netifd: VLAN 'eth0.1' link is up Sun Jun 28 16:05:48 2015 daemon.notice netifd: VLAN 'eth0.2' link is up Sun Jun 28 16:05:48 2015 daemon.notice netifd: Network device 'lo' link is up Sun Jun 28 16:05:48 2015 daemon.notice netifd: Interface 'loopback' has link connectivity Sun Jun 28 16:05:49 2015 user.notice firewall: Reloading firewall due to ifup of lan (br-lan) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.920000] cfg80211: Calling CRDA for country: FI Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.920000] cfg80211: Regulatory domain changed to country: FI Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.930000] cfg80211: DFS Master region: ETSI Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.930000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.940000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.960000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.970000] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 25.980000] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) Sun Jun 28 16:05:50 2015 daemon.info : 00[DMN] Starting IKE charon daemon (strongSwan 5.3.2, Linux 3.18.16, mips) Sun Jun 28 16:05:50 2015 kern.info kernel: [ 26.620000] br-lan: port 1(eth0.1) entered forwarding state Sun Jun 28 16:05:50 2015 kern.info kernel: [ 26.700000] br-lan: port 2(eth0.2) entered forwarding state Sun Jun 28 16:05:56 2015 daemon.notice netifd: radio0 (1226): Configuration file: /var/run/hostapd-phy0.conf Sun Jun 28 16:05:56 2015 kern.info kernel: [ 32.650000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready Sun Jun 28 16:05:56 2015 daemon.notice netifd: radio0 (1226): wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE Sun Jun 28 16:05:56 2015 kern.info kernel: [ 32.690000] device wlan0 entered promiscuous mode Sun Jun 28 16:05:56 2015 daemon.notice netifd: radio0 (1226): Using interface wlan0 with hwaddr 78:a3:51:01:27:bc and ssid "OpenWrt" Sun Jun 28 16:05:56 2015 daemon.notice netifd: radio0 (1226): wlan0: RADIUS Authentication server 10.0.0.1:1812 Sun Jun 28 16:05:56 2015 daemon.info hostapd: wlan0: RADIUS Authentication server 10.0.0.1:1812 Sun Jun 28 16:05:56 2015 daemon.notice netifd: radio0 (1226): wlan0: RADIUS Accounting server 10.0.0.1:1813 Sun Jun 28 16:05:56 2015 daemon.info hostapd: wlan0: RADIUS Accounting server 10.0.0.1:1813 Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.760000] br-lan: port 3(wlan0) entered forwarding state Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.760000] br-lan: port 3(wlan0) entered forwarding state Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.770000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Sun Jun 28 16:05:57 2015 daemon.notice netifd: wan (1225): sending -> AT Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.790000] device wlan0-1 entered promiscuous mode Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.800000] br-lan: port 4(wlan0-1) entered forwarding state Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.800000] br-lan: port 4(wlan0-1) entered forwarding state Sun Jun 28 16:05:57 2015 kern.info kernel: [ 32.810000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready Sun Jun 28 16:05:57 2015 daemon.notice netifd: radio0 (1226): Using interface wlan0-1 with hwaddr 78:a3:51:01:27:bd and ssid "leg" Sun Jun 28 16:05:57 2015 daemon.info dnsmasq[1395]: started, version 2.73 cachesize 150 Sun Jun 28 16:05:57 2015 daemon.info dnsmasq[1395]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify Sun Jun 28 16:05:57 2015 daemon.info dnsmasq-dhcp[1395]: DHCP, IP range 10.0.0.100 -- 10.0.0.159, lease time 12h Sun Jun 28 16:05:57 2015 daemon.info dnsmasq[1395]: using local addresses only for domain lan Sun Jun 28 16:05:57 2015 daemon.warn dnsmasq[1395]: no servers found in /tmp/resolv.conf.auto, will retry Sun Jun 28 16:05:57 2015 daemon.info dnsmasq[1395]: read /etc/hosts - 1 addresses Sun Jun 28 16:05:57 2015 daemon.info dnsmasq[1395]: read /tmp/hosts/dhcp - 1 addresses Sun Jun 28 16:05:57 2015 daemon.info dnsmasq-dhcp[1395]: read /etc/ethers - 0 addresses Sun Jun 28 16:05:57 2015 daemon.notice netifd: wan (1225): sending -> ATZ Sun Jun 28 16:05:57 2015 kern.info kernel: [ 33.660000] br-lan: port 4(wlan0-1) entered disabled state Sun Jun 28 16:05:58 2015 kern.info kernel: [ 33.830000] br-lan: port 4(wlan0-1) entered forwarding state Sun Jun 28 16:05:58 2015 kern.info kernel: [ 33.840000] br-lan: port 4(wlan0-1) entered forwarding state Sun Jun 28 16:05:58 2015 kern.info kernel: [ 33.840000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready Sun Jun 28 16:05:58 2015 daemon.notice netifd: radio0 (1226): wlan0: interface state COUNTRY_UPDATE->ENABLED Sun Jun 28 16:05:58 2015 daemon.notice netifd: radio0 (1226): wlan0: AP-ENABLED Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 33.870000] ------------[ cut here ]------------ Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 33.870000] WARNING: CPU: 0 PID: 79 at /usr/src/yocto/zbt/openwrt/build_dir/target-mipsel_24kec+dsp_musl-1.1.10/linux-ramips_mt7620/compat-wireless-2015-03-09/drivers/net/wireless/rt2x00/rt2800lib.c:1095 rt2800_get_txwi_rxwi_size+0x19c/0x268 [rt2800lib]() Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 33.890000] Modules linked in: rt2800soc rt2800pci rt2800mmio rt2800lib pppoe ppp_async option iptable_nat usb_wwan rt2x00soc rt2x00pci rt2x00mmio rt2x00lib pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_ncm cdc_ether xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_policy xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_id xt_hl xt_helper xt_esp xt_ecn xt_dsSun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.040000] CPU: 0 PID: 79 Comm: spi32766 Not tainted 3.18.16 #4 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.050000] Stack : 00000000 00000000 00000000 00000000 803541f2 00000034 0000004f 00000000 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.050000] 878fcc10 00000001 802bb57c 80314aa3 0000004f 8035341c 878fcc10 8724dd40 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.050000] 00000008 0000001c 00000001 8004778c 00000003 80024370 00000447 8724dd40 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.050000] 802beab4 009b1b04 00000000 00000000 00000000 00000000 00000000 00000000 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.050000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.050000] ... Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.080000] Call Trace: Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.090000] [<800141a0>] show_stack+0x48/0x70 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.090000] [<80024478>] warn_slowpath_common+0x84/0xb4 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.100000] [<80024530>] warn_slowpath_null+0x18/0x24 Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.100000] [<87224104>] rt2800_get_txwi_rxwi_size+0x19c/0x268 [rt2800lib] Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.110000] Sun Jun 28 16:05:58 2015 kern.warn kernel: [ 34.110000] ---[ end trace f001e2a9d322647c ]--- Sun Jun 28 16:05:58 2015 daemon.notice netifd: wan (1225): sending -> ATQ0 Sun Jun 28 16:05:58 2015 daemon.notice netifd: Network device 'wlan0' link is up Sun Jun 28 16:05:58 2015 daemon.notice netifd: Network device 'wlan0-1' link is up Sun Jun 28 16:05:59 2015 kern.info kernel: [ 34.760000] br-lan: port 3(wlan0) entered forwarding state Sun Jun 28 16:05:59 2015 user.emerg : setting up led wlan Sun Jun 28 16:05:59 2015 daemon.notice netifd: wan (1225): sending -> ATV1 Sun Jun 28 16:06:00 2015 kern.info kernel: [ 35.840000] br-lan: port 4(wlan0-1) entered forwarding state Sun Jun 28 16:06:00 2015 daemon.info procd: - init complete - Sun Jun 28 16:06:00 2015 daemon.info dnsmasq-dhcp[1395]: DHCPDISCOVER(br-lan) c8:2a:14:22:35:3a Sun Jun 28 16:06:00 2015 daemon.info dnsmasq-dhcp[1395]: DHCPOFFER(br-lan) 10.0.0.50 c8:2a:14:22:35:3a Sun Jun 28 16:06:00 2015 daemon.notice netifd: wan (1225): sending -> ATE1 Sun Jun 28 16:06:01 2015 daemon.notice netifd: wan (1225): sending -> ATS0=0 Sun Jun 28 16:06:01 2015 daemon.info dnsmasq-dhcp[1395]: DHCPREQUEST(br-lan) 10.0.0.50 c8:2a:14:22:35:3a Sun Jun 28 16:06:01 2015 daemon.info dnsmasq-dhcp[1395]: DHCPACK(br-lan) 10.0.0.50 c8:2a:14:22:35:3a imac Sun Jun 28 16:06:01 2015 daemon.info watchdog: Re-connecting WAN interface Sun Jun 28 16:06:02 2015 daemon.notice netifd: wan (1657): Stopping network Sun Jun 28 16:06:02 2015 daemon.info : 00[LIB] created TUN device: ipsec0 Sun Jun 28 16:06:03 2015 daemon.notice netifd: Interface 'VPN' is enabled Sun Jun 28 16:06:03 2015 daemon.notice netifd: Network device 'ipsec0' link is up Sun Jun 28 16:06:03 2015 daemon.notice netifd: Interface 'VPN' has link connectivity Sun Jun 28 16:06:03 2015 daemon.notice netifd: Interface 'VPN' is setting up now Sun Jun 28 16:06:03 2015 daemon.notice netifd: Interface 'VPN' is now up Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loading ca certificates from '/etc/ipsec.d/cacerts' Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loaded ca certificate "C=FI, O=Koti, CN=Osku" from '/etc/ipsec.d/cacerts/caCert.pem' Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loading aa certificates from '/etc/ipsec.d/aacerts' Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loading ocsp signer certificates from '/etc/ipsec.d/ocspcerts' Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loading attribute certificates from '/etc/ipsec.d/acerts' Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loading crls from '/etc/ipsec.d/crls' Sun Jun 28 16:06:03 2015 daemon.info : 00[CFG] loading secrets from '/etc/ipsec.secrets' Sun Jun 28 16:06:03 2015 user.notice firewall: Reloading firewall due to ifup of VPN (ipsec0) Sun Jun 28 16:06:04 2015 daemon.notice netifd: wan (1657): sending -> Sun Jun 28 16:06:04 2015 daemon.info : 00[CFG] loaded RSA private key from '/etc/ipsec.d/private/serverKey.pem' Sun Jun 28 16:06:04 2015 daemon.info : 00[CFG] loaded EAP secret for osku-vpn Sun Jun 28 16:06:04 2015 daemon.info : 00[CFG] loaded EAP secret for osku Sun Jun 28 16:06:04 2015 daemon.info : 00[LIB] loaded plugins: charon test-vectors pkcs11 aes des blowfish sha1 sha2 md4 md5 random nonce x509 revocation constraints pubkey pkcs1 pkcs8 pgp dnskey pem openssl gcrypt af-alg fips-prf gmp xcbc hmac attr kernel-libipsec kernel-netlink resolve socket-default farp stroke updown xauth-generic dhcp Sun Jun 28 16:06:04 2015 daemon.info : 00[JOB] spawning 16 worker threads Sun Jun 28 16:06:04 2015 authpriv.info ipsec_starter[1222]: charon (1224) started after 8980 ms Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] received stroke: add connection 'ios' Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] left nor right host is our side, assuming left=local Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] loaded certificate "C=FI, O=Koti, CN=niisku.ignorelist.com" from 'serverCert.pem' Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] id '%any' not confirmed by certificate, defaulting to 'C=FI, O=Koti, CN=niisku.ignorelist.com' Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] loaded certificate "C=FI, O=Koti, CN=Osku" from 'clientCert.pem' Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] id '%any' not confirmed by certificate, defaulting to 'C=FI, O=Koti, CN=Osku' Sun Jun 28 16:06:04 2015 daemon.info : 12[CFG] added configuration 'ios' Sun Jun 28 16:06:06 2015 user.notice firewall: Reloading IPSec after firewall restart Sun Jun 28 16:06:06 2015 daemon.info : 00[DMN] signal of type SIGINT received. Shutting down Sun Jun 28 16:06:06 2015 daemon.notice netifd: Network device 'ipsec0' link is down Sun Jun 28 16:06:06 2015 daemon.notice netifd: Interface 'VPN' has link connectivity loss Sun Jun 28 16:06:06 2015 daemon.notice netifd: Interface 'VPN' is now down Sun Jun 28 16:06:06 2015 authpriv.info ipsec_starter[1222]: charon stopped after 200 ms Sun Jun 28 16:06:06 2015 authpriv.info ipsec_starter[1222]: ipsec starter stopped Sun Jun 28 16:06:06 2015 daemon.notice netifd: Interface 'VPN' is disabled Sun Jun 28 16:06:07 2015 daemon.notice netifd: Interface 'wan' is now down Sun Jun 28 16:06:07 2015 daemon.notice netifd: Interface 'wan' is setting up now Sun Jun 28 16:06:08 2015 authpriv.info ipsec_starter[2050]: Starting strongSwan 5.3.2 IPsec [starter]... Sun Jun 28 16:06:08 2015 daemon.err modprobe: ah4 is already loaded Sun Jun 28 16:06:08 2015 daemon.err modprobe: esp4 is already loaded Sun Jun 28 16:06:08 2015 daemon.err modprobe: ipcomp is already loaded Sun Jun 28 16:06:08 2015 daemon.err modprobe: xfrm4_tunnel is already loaded Sun Jun 28 16:06:08 2015 daemon.err modprobe: xfrm_user is already loaded Sun Jun 28 16:06:08 2015 daemon.info : 00[DMN] Starting IKE charon daemon (strongSwan 5.3.2, Linux 3.18.16, mips) Sun Jun 28 16:06:08 2015 daemon.notice netifd: Interface 'VPN' is enabled Sun Jun 28 16:06:08 2015 daemon.notice netifd: Network device 'ipsec0' link is up Sun Jun 28 16:06:08 2015 daemon.notice netifd: Interface 'VPN' has link connectivity Sun Jun 28 16:06:08 2015 daemon.notice netifd: Interface 'VPN' is setting up now Sun Jun 28 16:06:08 2015 daemon.info : 00[LIB] created TUN device: ipsec0 Sun Jun 28 16:06:08 2015 daemon.notice netifd: Interface 'VPN' is now up Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loading ca certificates from '/etc/ipsec.d/cacerts' Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loaded ca certificate "C=FI, O=Koti, CN=Osku" from '/etc/ipsec.d/cacerts/caCert.pem' Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loading aa certificates from '/etc/ipsec.d/aacerts' Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loading ocsp signer certificates from '/etc/ipsec.d/ocspcerts' Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loading attribute certificates from '/etc/ipsec.d/acerts' Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loading crls from '/etc/ipsec.d/crls' Sun Jun 28 16:06:08 2015 daemon.info : 00[CFG] loading secrets from '/etc/ipsec.secrets' Sun Jun 28 16:06:09 2015 user.notice firewall: Reloading firewall due to ifup of VPN (ipsec0) Sun Jun 28 16:06:09 2015 daemon.info : 00[CFG] loaded RSA private key from '/etc/ipsec.d/private/serverKey.pem' Sun Jun 28 16:06:09 2015 daemon.info : 00[CFG] loaded EAP secret for osku-vpn Sun Jun 28 16:06:09 2015 daemon.info : 00[CFG] loaded EAP secret for osku Sun Jun 28 16:06:09 2015 daemon.info : 00[LIB] loaded plugins: charon test-vectors pkcs11 aes des blowfish sha1 sha2 md4 md5 random nonce x509 revocation constraints pubkey pkcs1 pkcs8 pgp dnskey pem openssl gcrypt af-alg fips-prf gmp xcbc hmac attr kernel-libipsec kernel-netlink resolve socket-default farp stroke updown xauth-generic dhcp Sun Jun 28 16:06:09 2015 daemon.info : 00[JOB] spawning 16 worker threads Sun Jun 28 16:06:09 2015 authpriv.info ipsec_starter[2063]: charon (2066) started after 1220 ms Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] received stroke: add connection 'ios' Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] left nor right host is our side, assuming left=local Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] loaded certificate "C=FI, O=Koti, CN=niisku.ignorelist.com" from 'serverCert.pem' Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] id '%any' not confirmed by certificate, defaulting to 'C=FI, O=Koti, CN=niisku.ignorelist.com' Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] loaded certificate "C=FI, O=Koti, CN=Osku" from 'clientCert.pem' Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] id '%any' not confirmed by certificate, defaulting to 'C=FI, O=Koti, CN=Osku' Sun Jun 28 16:06:09 2015 daemon.info : 05[CFG] added configuration 'ios' Sun Jun 28 16:06:11 2015 kern.notice kernel: [ 47.510000] random: nonblocking pool is initialized Sun Jun 28 16:06:13 2015 daemon.notice netifd: wan (2042): WARNING: Variable 'modes' does not exist or is not an array/object Sun Jun 28 16:06:14 2015 daemon.notice netifd: wan (2042): sending -> Sun Jun 28 16:06:29 2015 daemon.notice netifd: wan (2042): Timeout running AT-command Sun Jun 28 16:06:29 2015 daemon.notice netifd: wan (2042): Failed to set operating mode Sun Jun 28 16:06:29 2015 daemon.notice netifd: wan (2471): Stopping network Sun Jun 28 16:06:31 2015 daemon.notice netifd: wan (2471): sending -> AT^NDISDUP=1,0 Sun Jun 28 16:06:31 2015 daemon.notice netifd: wan (2471): Error running AT-command Sun Jun 28 16:06:31 2015 daemon.notice netifd: wan (2471): Failed to disconnect Sun Jun 28 16:06:31 2015 daemon.notice netifd: Interface 'wan' is now down Sun Jun 28 16:06:31 2015 daemon.notice netifd: Interface 'wan' is setting up now Sun Jun 28 16:06:39 2015 daemon.notice netifd: wan (2483): sending -> AT Sun Jun 28 16:06:39 2015 daemon.notice netifd: wan (2483): sending -> ATZ Sun Jun 28 16:06:40 2015 daemon.notice netifd: wan (2483): sending -> ATQ0 Sun Jun 28 16:06:41 2015 daemon.notice netifd: wan (2483): sending -> ATV1 Sun Jun 28 16:06:41 2015 daemon.notice netifd: wan (2483): sending -> ATE1 Sun Jun 28 16:06:42 2015 daemon.notice netifd: wan (2483): sending -> ATS0=0 Sun Jun 28 16:06:42 2015 daemon.notice netifd: wan (2483): sending -> AT^SYSCFGEX="0201",3fffffff,2,3,7fffffffffffffff,, Sun Jun 28 16:06:44 2015 daemon.notice netifd: wan (2483): sending -> AT^NDISDUP=1,1,"internet4" Sun Jun 28 16:06:50 2015 daemon.notice netifd: wan (2483): Connected, starting DHCP Sun Jun 28 16:06:50 2015 kern.err kernel: [ 85.870000] cdc_ether 1-1.2:1.0 eth1: kevent 12 may have been dropped Sun Jun 28 16:06:50 2015 kern.err kernel: [ 85.870000] cdc_ether 1-1.2:1.0 eth1: kevent 11 may have been dropped Sun Jun 28 16:06:50 2015 daemon.info : 03[KNL] interface eth1 activated Sun Jun 28 16:06:50 2015 daemon.notice netifd: Interface 'wan6' is enabled Sun Jun 28 16:06:50 2015 daemon.notice netifd: Interface 'wan' is now up Sun Jun 28 16:06:50 2015 kern.err kernel: [ 85.900000] cdc_ether 1-1.2:1.0 eth1: kevent 11 may have been dropped Sun Jun 28 16:06:50 2015 daemon.notice netifd: Interface 'wan_4' is enabled Sun Jun 28 16:06:50 2015 daemon.notice netifd: wan (2483): Command failed: Unknown error Sun Jun 28 16:06:50 2015 daemon.notice netifd: Interface 'wan_6' is enabled Sun Jun 28 16:06:50 2015 daemon.notice netifd: wan (2483): Command failed: Unknown error _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Bleeding Edge, r46133) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@gateway:/#

Notes

I got only 1 of led to work (wifi led)
SD-Card interface works presenting the card as /dev/mmcblk0. Tested with installed ext4 modules and some ext4 formatted card

Table of Contents