Ubiquiti LiteBeam 5AC Gen2 (LBE-5AC-Gen2) is a dual band outdoor PoE CPE packed inside feedhorn that attaches to small directional reflector included in the package. airOS utilizes 2.4GHz wifi as a management radio only, thus it's performance and range are less than 5GHz wifi.
* with newer devices, and bigger images, you might get a LZMA error during bootm. If it happens, try using 0x82000000 in tftpboot and bootm.
tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
bootm 0x81000000
openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
to /tmpsysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
Architecture | MIPS |
---|---|
Vendor | Ubiquiti |
Bootloader | U-Boot |
System-On-Chip | Atheros AR9342 - MIPS 74Kc V4.12 |
CPU/Speed | 535 MHz |
Flash-Chip | Macronix MX25L12805D |
Flash size | 16 MiB |
RAM | 64 MiB |
Wireless | Atheros AR9342 & Qualcomm/Atheros QCA988X |
Ethernet | 1000/100/10 Mbit/s (Atheros AR8035 PHY) |
USB | None |
Serial | Yes |
JTAG | No |
Please read the article flash.layout for a better understanding. It contains a couple of explanations. Then let's have a quick view at flash layout of this particular device:
Ubiquiti LiteBeam 5AC Gen2 Flash Layout stock firmware | |||||||
---|---|---|---|---|---|---|---|
Layer0 | m25p128 spi0.0: Macronix MX25L12805D 16384KiB | ||||||
Layer1 | mtd0 | mtd1 | mtd2 | mtd3 | mtd4 | mtd5 | |
Size in KiB | 256KiB | 64KiB | 1024KiB | 14720KiB | 256KiB | 64KiB | |
Name | u-boot | u-boot-env | kernel | rootfs | cfg | EEPROM | |
mountpoint | none | none | none | / | none | none | |
filesystem | none | none | none | SquashFS 4.0 | none | none | |
Ubiquiti LiteBeam 5AC Gen2 Flash Layout | |||||||
Layer0 | m25p128 spi0.0: Macronix MX25L12805D 16384KiB | ||||||
Layer1 | mtd0 u-boot 256KiB | mtd1 u-boot-env 64KiB | mtd2 firmware 15744KiB | mtd6 cfg 256 KiB | mtd7 EEPROM 64KiB | ||
Layer2 | mtd3 kernel | mtd4 rootfs | |||||
mountpoint | / | ||||||
filesystem | overlayfs | ||||||
Layer3 | mtd5 rootfs_data | ||||||
Size in KiB | 256KiB | 64KiB | 256KiB | 64KiB | |||
Name | u-boot | u-boot-env | kernel | rootfs_data | cfg | EEPROM | |
mountpoint | none | none | none | /rom | /overlay | none | none |
filesystem | none | none | none | SquashFS | JFFS2 | none | none |
Ubiquiti LiteBeam 5AC Gen2 has the following buttons:
BUTTON | Event |
---|---|
Reset | reset |
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Serial connection parameters for Ubiquiti LiteBeam 5AC Gen2 | 115200, 8N1 |
---|
[ 0.000000] Linux version 2.6.32.68 (jenkins@9496cb8761c7) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 unknown) ) #1 Wed Apr 25 08:50:18 EEST 2018 [ 0.000000] flash_size passed from bootloader = 16 [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80295080, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs init=/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),1024k(kernel),14720k(rootfs),256k(cfg),64k(EEPROM) mem=64M panic=3 quiet [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61760k/65536k available (2128k kernel code, 3704k reserved, 513k data, 132k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] plat_time_init: plat time init done [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled [ 0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=133120) [ 0.022000] Mount-cache hash table entries: 512 [ 0.024000] NET: Registered protocol family 16 [ 0.026000] PCIe WLAN H/W found [tries: 1] [ 0.026000] PCI init:ath_pcibios_init [ 0.027000] ath_pcibios_init(419): PCI CMD write: 0x356 [ 0.027000] registering PCI controller with io_map_base unset [ 0.032000] bio: create slab <bio-0> at 0 [ 0.033000] pci 0000:00:00.0: reg 10 64bit mmio: [0x000000-0x1fffff] [ 0.034000] pci 0000:00:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] [ 0.034000] pci 0000:00:00.0: supports D1 D2 [ 0.034000] Returning IRQ 64 [ 0.035000] Switching to clocksource MIPS [ 0.037000] NET: Registered protocol family 2 [ 0.038000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.039000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.039000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.039000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.039000] TCP reno registered [ 0.040000] NET: Registered protocol family 1 [ 0.040000] ATH GPIOC major 0 [ 0.041000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.041000] msgmni has been set to 120 [ 0.042000] io scheduler noop registered (default) [ 0.066000] Serial: Atheros High-Speed UART (115200) [ 0.066000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.067000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A [ 0.067000] console [ttyS0] enabled [ 0.069000] 6 cmdlinepart partitions found on MTD device ath-nor0 [ 0.069000] Creating 6 MTD partitions on "ath-nor0": [ 0.069000] 0x000000000000-0x000000040000 : "u-boot" [ 0.070000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.071000] 0x000000050000-0x000000150000 : "kernel" [ 0.072000] 0x000000150000-0x000000fb0000 : "rootfs" [ 0.073000] mtd: partition "rootfs" set to be root filesystem [ 0.073000] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.075000] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.076000] u32 classifier [ 0.076000] Performance counters on [ 0.076000] input device check on [ 0.076000] Actions configured [ 0.078000] TCP westwood registered [ 0.078000] NET: Registered protocol family 10 [ 0.081000] NET: Registered protocol family 17 [ 0.081000] Bridge firewalling registered [ 0.081000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 0.081000] All bugs added by David S. Miller <davem@redhat.com> [ 0.081000] athwdt_init: Registering WDT success [ 0.082000] Reset: Normal [ 0.082000] ath_otp_init: Registering OTP success [ 0.082000] ath_clksw_init: Registering Clock Switch Interface success [ 0.089000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.090000] Freeing unused kernel memory: 132k freed [ 1.636000] ubnthal: module license 'Proprietary' taints kernel. [ 1.636000] Disabling lock debugging due to kernel taint [ 1.683000] ubnthal: initializing... [ 1.683000] ath-gpio 2.0 initialised [ 1.683000] ubnthal: initialised, board found, sysid = 0xe7f9, name = LiteBeam 5AC Gen2 [ 1.683000] ubnthal: host_board_t size: 7392B, boards table size: 166kB [ 6.901000] ATHR_GMAC: Length per segment 1536 [ 6.901000] ATHR_GMAC: fifo cfg 3 01f00140 [ 6.902000] Found PHY at address 4 with ID 4d:d072 [ 6.902000] Registering AR8035 Phy.... [ 6.902000] ATHR_GMAC: RX TASKLET - Pkts per Intr:160 [ 6.902000] ATHR_GMAC: Mac address for unit 0:bfff0000 [ 6.902000] ATHR_GMAC: b4:fb:e4:a5:88:74 [ 7.456000] ATHR_GMAC: Max segments per packet : 1 [ 7.456000] ATHR_GMAC: Max tx descriptor count : 128 [ 7.456000] ATHR_GMAC: Max rx descriptor count : 252 [ 7.456000] ATHR_GMAC: Mac capability flags : 42200 [ 7.568000] PPP generic driver version 2.4.2 [ 7.628000] PPP MPPE Compression module registered [ 7.661000] NET: Registered protocol family 24 [ 7.830000] GRE over IPv4 tunneling driver [ 7.947000] URD Init [ 8.398000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, 11D) [ 8.564000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 8.679000] ath_spectral: Version 2.0.0 [ 8.679000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 8.680000] SPECTRAL module built on Apr 25 2018 08:48:56 [ 8.947000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 10.867000] ath_pci: 10.1.467 (Atheros/multi-bss) [ 10.867000] Ubiquiti U-AME chipset detected [ 10.867000] ath_pci_probe [ 10.867000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 10.868000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x83b27a00 [ 10.868000] [ 10.868000] ol_ath_pci_configure : num_desired MSI set to 0 [ 10.868000] [ 10.868000] Using PCI Legacy Interrupt [ 10.980000] __ol_ath_attach: ath_attach TODO [ 10.981000] ol_ath_attach() BMI inited. [ 10.981000] ol_ath_attach() BMI Get Target Info. [ 10.981000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 10.982000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 10.982000] ol_ath_attach() configure Target . [ 10.982000] qc98xx_verify_checksum: flash checksum passed: 0x13b5 [ 10.982000] ol_transfer_bin_file 338: Download Flash data len 2116 [ 10.996000] BMI operation done [ 10.996000] ol_transfer_bin_file 259: Download Firmware data len 214160. Mode: PTP [ 11.905000] BMI operation done [ 11.905000] ol_ath_attach() Download FW. [ 11.905000] ol_ath_attach() HT Create . [ 11.905000] ol_ath_attach() HIF Claim. [ 11.905000] ol_ath_attach() BMI Done. [ 11.906000] ol_ath_attach() WMI attached. wmi_handle 83b70000 [ 11.906000] +HWT [ 11.909000] -HWT [ 11.909000] HTC Service:0x0300 ep:1 TX flow control disabled [ 11.914000] ol_txrx_pdev_attach: tx_credit initialised to 1424 [ 11.914000] HTC Service:0x0100 ep:2 TX flow control disabled [ 11.914000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 11.914000] num_rf_chain : 00000002 [ 11.914000] ht_cap_info: : 0000085b [ 11.914000] vht_cap_info : 338001b2 [ 11.914000] vht_supp_mcs : 0000fffa [ 11.923000] FIRMWARE:P 34 V 1 T 110 [ 11.923000] [ 11.923000] wmi_ready_event_rx: WMI UNIFIED READY event [ 11.924000] ol_ath_connect_htc() WMI is ready [ 11.924000] ol_ath_set_host_app_area TODO [ 11.924000] target uses HTT version 2.1; host uses 2.1 [ 11.924000] ol_ath_attach() connect HTC. [ 11.924000] Supported modes: 0x1f9001 [ 11.924000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 11.978000] ol_ath_phyerr_attach: called [ 11.979000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 11.985000] OL Resmgr Init-ed [ 11.986000] ol_if_spectral_setup [ 11.986000] SPECTRAL : get_capability not registered [ 11.986000] HAL_CAP_PHYDIAG : Capable [ 11.986000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 234) [ 11.986000] SPECTRAL : get_capability not registered [ 11.986000] HAL_CAP_RADAR : Capable [ 11.986000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 11.986000] (spectral_attach : 239) [ 11.986000] SPECTRAL : get_capability not registered [ 11.986000] HAL_CAP_SPECTRAL_SCAN : Capable [ 11.986000] SPECTRAL : get_tsf64 not registered [ 11.986000] spectral_init_netlink 54 NULL SKB [ 11.986000] ol_ath_set_dscp_tid_map: ...ath.c [ 11.986000] ol_if_dfs_setup: called [ 11.986000] ol_ath_rtt_meas_report_attach: called [ 11.986000] ol_ath_attach() UMAC attach . [ 11.986000] __ol_ath_attach: init tx/rx TODO [ 11.986000] __ol_ath_attach: hard_header_len reservation 64 [ 11.986000] __ol_ath_attach: dev name wifi0 [ 11.990000] ath_ahb: 10.1.467 (Atheros/multi-bss) [ 11.991000] __ath_attach: Set global_scn[0] [ 11.991000] ACBKMinfree = 48 [ 11.991000] ACBEMinfree = 32 [ 11.991000] ACVIMinfree = 16 [ 11.991000] ACVOMinfree = 0 [ 11.991000] CABMinfree = 48 [ 11.991000] UAPSDMinfree = 0 [ 12.001000] Enterprise mode: 0x00000000 [ 12.002000] Restoring Cal data from Flash [ 12.378000] SPECTRAL : get_capability not registered [ 12.378000] HAL_CAP_PHYDIAG : Capable [ 12.378000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 234) [ 12.378000] SPECTRAL : get_capability not registered [ 12.378000] HAL_CAP_RADAR : Capable [ 12.378000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 12.378000] (spectral_attach : 239) [ 12.378000] SPECTRAL : get_capability not registered [ 12.378000] HAL_CAP_SPECTRAL_SCAN : Capable [ 12.378000] SPECTRAL : get_tsf64 not registered [ 12.378000] spectral_init_netlink 54 NULL SKB [ 12.378000] IRQ request for SPECTRAL-XMIT-FILTER successful [ 12.378000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT [ 12.378000] SPECTRAL : module attached [ 12.382000] ath_get_caps[5784] rx chainmask mismatch actual 3 sc_chainmak 0 [ 12.382000] ath_get_caps[5759] tx chainmask mismatch actual 3 sc_chainmak 0 [ 12.383000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 12.415000] SPECTRAL : module already attached [ 12.417000] ath_tx_paprd_init sc 827a0000 PAPRD Enabled [ 12.702000] wifi1: Atheros 9340: mem=0xb8100000, irq=2 [ 12.927000] ubnt_poll_host: Hooks registered [ 12.927000] ubnt_poll_host: Allocated chardev region for major 189 [ 13.049000] rssi-leds 1.2 loaded [ 13.364000] Mirror/redirect action on [ 14.432000] ath_dfs: Version 2.0.0 [ 14.432000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 14.577000] ath92.ol_ath_set_config_param(): Reset scheduled on wifi0 radio [ 14.577000] Resetting the radio [ 14.577000] Suspending Target - with disable_intr set [ 14.577000] waiting for target paused event from target [ 14.580000] __ol_ath_detach: init tx/rx cleanup TODO [ 14.580000] ol_if_dfs_teardown: called [ 14.580000] ol_ath_phyerr_detach: called [ 14.583000] ol_if_spectral_detach [ 14.583000] SPECTRAL : Module removed (spectral = 83bfd000) [ 14.583000] ath_pci_warm_reset :(sc 83b27a00) [ 14.583000] Target Warm Reset [ 14.583000] Host Intr Cause reg 0x900c : value : 0x4000 [ 14.583000] Target CPU Intr Cause 0x5000 [ 14.683000] addr 0x4050 : 0x4 [ 14.703000] Target CPU Intr Cause after CE reset 0x0 [ 14.703000] RESET_CONTROL after cpu warm reset 0x800 [ 14.804000] Target Warm reset complete [ 14.804000] ath_pci_remove [ 14.804000] Ubiquiti U-AME chipset detected [ 14.804000] ath_pci_probe [ 14.804000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 14.804000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x83b27a00 [ 14.804000] [ 14.804000] ol_ath_pci_configure : num_desired MSI set to 0 [ 14.804000] [ 14.804000] Using PCI Legacy Interrupt [ 14.916000] __ol_ath_attach: ath_attach TODO [ 14.918000] ol_ath_attach() BMI inited. [ 14.923000] ol_ath_attach() BMI Get Target Info. [ 14.923000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 14.923000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 14.924000] ol_ath_attach() configure Target . [ 14.924000] qc98xx_verify_checksum: flash checksum passed: 0x13b5 [ 14.924000] ol_transfer_bin_file 338: Download Flash data len 2116 [ 14.938000] BMI operation done [ 14.938000] ol_transfer_bin_file 259: Download Firmware data len 214160. Mode: PTP [ 15.862000] BMI operation done [ 15.862000] ol_ath_attach() Download FW. [ 15.862000] ol_ath_attach() HT Create . [ 15.862000] ol_ath_attach() HIF Claim. [ 15.862000] ol_ath_attach() BMI Done. [ 15.863000] ol_ath_attach() WMI attached. wmi_handle 83b70000 [ 15.863000] +HWT [ 15.865000] -HWT [ 15.866000] HTC Service:0x0300 ep:1 TX flow control disabled [ 15.870000] ol_txrx_pdev_attach: tx_credit initialised to 1424 [ 15.870000] HTC Service:0x0100 ep:2 TX flow control disabled [ 15.871000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 15.871000] num_rf_chain : 00000002 [ 15.871000] ht_cap_info: : 0000085b [ 15.871000] vht_cap_info : 338001b2 [ 15.871000] vht_supp_mcs : 0000fffa [ 15.880000] FIRMWARE:P 34 V 1 T 110 [ 15.880000] [ 15.880000] wmi_ready_event_rx: WMI UNIFIED READY event [ 15.880000] ol_ath_connect_htc() WMI is ready [ 15.880000] ol_ath_set_host_app_area TODO [ 15.880000] ol_ath_attach() connect HTC. [ 15.880000] target uses HTT version 2.1; host uses 2.1 [ 15.880000] Supported modes: 0x1f9001 [ 15.880000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 15.935000] ol_ath_phyerr_attach: called [ 15.935000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 15.942000] OL Resmgr Init-ed [ 15.942000] ol_if_spectral_setup [ 15.942000] SPECTRAL : get_capability not registered [ 15.942000] HAL_CAP_PHYDIAG : Capable [ 15.942000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 234) [ 15.942000] SPECTRAL : get_capability not registered [ 15.942000] HAL_CAP_RADAR : Capable [ 15.942000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 15.942000] (spectral_attach : 239) [ 15.942000] SPECTRAL : get_capability not registered [ 15.942000] HAL_CAP_SPECTRAL_SCAN : Capable [ 15.942000] SPECTRAL : get_tsf64 not registered [ 15.942000] spectral_init_netlink 54 NULL SKB [ 15.943000] ol_ath_set_dscp_tid_map: ...ath.c [ 15.943000] ol_if_dfs_setup: called [ 15.943000] ol_ath_rtt_meas_report_attach: called [ 15.943000] ol_ath_attach() UMAC attach . [ 15.943000] __ol_ath_attach: init tx/rx TODO [ 15.943000] __ol_ath_attach: hard_header_len reservation 64 [ 15.943000] __ol_ath_attach: dev name wifi0 [ 15.985000] Reset of radio done [ 15.985000] ubnt_poll_host: Hooks registered [ 15.985000] ubnt_poll_host: Allocated chardev region for major 189 [ 16.052000] ubnt_poll_host wifi0: Char device created succesfully err 0 [ 16.053000] ubnt_poll_host: Polling enabled for radio wifi0 [ 16.053000] ubnt_poll_host: noack_mode set to 0 for radio wifi0 [ 16.053000] ubnt_poll_host: DAPROT set to 0 for radio wifi0 [ 16.053000] ubnt-poll-host: [wifi0] Station priority configured to 2 (no-auto=0) [ 16.053000] ubnt_poll_host: Fixed frame mode disabled for radio wifi0 [ 16.194000] ath_ioctl: SIOC80211IFCREATE CALLED [ 16.194000] ubnt_poll_host: Initialized in PTP STA mode for device wifi0 [ 16.195000] wmi_unified_set_psmode:set psmode=1 [ 16.195000] ol_if_dfs_attach: called; ptr=83126ffc, radar_info=8322d908 [ 16.200000] ol_if_dfs_configure: called [ 16.200000] ol_if_dfs_configure: FCC domain [ 16.200000] ol_if_dfs_disable: called [ 16.200000] ol_ath_phyerr_disable: about to send [ 16.201000] VAP device ath0 created [ 16.231000] dfs_control debug flags now 0x00000003 [ 16.276000] BW divisor: 0X411 [ 16.369000] ath_dfs: another dfs module already in use [ 16.378000] wlan_vap_create : enter. devhandle=0x827902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 16.379000] wlan_vap_create : exit. devhandle=0x827902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. [ 16.379000] VAP device ath1 created [ 16.390000] [ 16.390000] DES SSID SET=LBE-5AC-Gen2:B4FBE4A48874 [ 16.692000] Invoking ACS module for Best channel selection [ 16.903000] ubnt_poll_host: ATPC enabled (0/0/0/24) for radio wifi0 [ 17.010000] [ 17.010000] DES SSID SET=ubnt [ 17.020000] ol_ath_vap_set_param: VAP param unsupported param:33 value:0 [ 17.050000] wmi_unified_set_psmode:set psmode=0 [ 17.050000] wmi_unified_set_psmode:set psmode=0 [ 17.495000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 17.712000] Ebtables v2.0 registered [ 17.858000] xt_time: kernel timezone is -0000 [ 18.022000] nf_conntrack version 0.5.0 (968 buckets, 3872 max) [ 18.023000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 18.023000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 18.023000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 18.929000] ieee80211_acs_find_best_centerchan: ACS picked 2437 as best channel [ 19.236000] device eth0 entered promiscuous mode [ 19.248000] device ath0 entered promiscuous mode [ 19.261000] ath_paprd_cal sc 827a0000 chan_mask 3 PAPRD excessive failure disabling PAPRD now [ 19.405000] athr_gmac_ring_alloc Allocated 2048 at 0x81f4a800 [ 19.405000] sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000 [ 19.405000] athr_gmac_ring_alloc Allocated 4032 at 0x820e0000 [ 19.405000] sram_desc_cnt 4560,mac Unit 0,Rx r->ring_desc 0xbd000600 [ 19.705000] WASP ----> AR8035 PHY [ 19.706000] AR8035 Detected [ 19.706000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 19.706000] Setting PHY... [ 19.706000] Forced AR8035 PHY hardware reset on PHY setup. [ 19.819000] AR8035 - ID 0x004d:0xd072 [ 26.031000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 27.780000] br0: port 2(ath0) entering learning state [ 28.780000] br0: port 2(ath0) entering forwarding state
[ 0.000000] Linux version 4.14.118 (ubuntu@ubuntu) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10011-71ab2c9)) #0 Wed May 15 11:34:24 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is Ubiquiti LiteBeam AC Gen2 [ 0.000000] SoC: Atheros AR9342 rev 3 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 804cbf90, node_mem_map 81006f00 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 58540K/65536K available (3518K kernel code, 141K rwdata, 872K rodata, 1220K init, 201K bss, 6996K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 535.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns [ 0.000012] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns [ 0.008326] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.094953] pid_max: default: 32768 minimum: 301 [ 0.100094] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.107153] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.119302] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.129825] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.136409] pinctrl core: initialized pinctrl subsystem [ 0.143121] NET: Registered protocol family 16 [ 0.155791] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges: [ 0.162729] MEM 0x0000000010000000..0x0000000013ffffff [ 0.168293] IO 0x0000000000000000..0x0000000000000000 [ 0.192152] PCI host bridge to bus 0000:00 [ 0.196596] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.203909] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.209850] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.217071] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.225555] pci 0000:00:00.0: [0777:11ac] type 00 class 0x028000 [ 0.225621] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.225678] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.225764] pci 0000:00:00.0: supports D1 D2 [ 0.226008] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.226041] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.233841] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.244601] clocksource: Switched to clocksource MIPS [ 0.251213] NET: Registered protocol family 2 [ 0.256810] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.264250] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.271082] TCP: Hash tables configured (established 1024 bind 1024) [ 0.278026] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.284261] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.291304] NET: Registered protocol family 1 [ 0.296063] PCI: CLS 0 bytes, default 32 [ 0.299459] Crashlog allocated RAM at address 0x3f00000 [ 0.306594] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.319235] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.325497] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.346470] io scheduler noop registered [ 0.350652] io scheduler deadline registered (default) [ 0.358674] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68 [ 0.367263] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.374942] console [ttyS0] disabled [ 0.378796] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A [ 0.388029] console [ttyS0] enabled [ 0.395458] bootconsole [early0] disabled [ 0.416158] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.421355] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.427827] Creating 5 MTD partitions on "spi0.0": [ 0.432698] 0x000000000000-0x000000040000 : "u-boot" [ 0.438785] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.445195] 0x000000050000-0x000000fb0000 : "firmware" [ 0.453768] 2 uimage-fw partitions found on MTD device firmware [ 0.459838] Creating 2 MTD partitions on "firmware": [ 0.464899] 0x000000000000-0x000000180000 : "kernel" [ 0.470833] 0x000000180000-0x000000f60000 : "rootfs" [ 0.476805] mtd: device 4 (rootfs) set to be root filesystem [ 0.482588] 1 squashfs-split partitions found on MTD device rootfs [ 0.488928] 0x0000005d0000-0x000000f60000 : "rootfs_data" [ 0.495390] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.501062] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.508414] libphy: Fixed MDIO Bus: probed [ 0.856511] libphy: ag71xx_mdio: probed [ 0.954809] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:04 [uid=004dd072, driver=Atheros 8035 ethernet] [ 0.965855] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii [ 0.973329] NET: Registered protocol family 17 [ 0.978013] 8021q: 802.1Q VLAN Support v1.8 [ 0.989817] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.005013] Freeing unused kernel memory: 1220K [ 1.009611] This architecture does not have kernel memory protection. [ 1.716867] init: Console is alive [ 1.720589] init: - watchdog - [ 2.424644] random: fast init done [ 2.932216] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.069395] usbcore: registered new interface driver usbfs [ 3.075159] usbcore: registered new interface driver hub [ 3.080661] usbcore: registered new device driver usb [ 3.093404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.102102] ehci-platform: EHCI generic platform driver [ 3.108428] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.126367] init: - preinit - [ 4.523664] random: jshn: uninitialized urandom read (4 bytes read) [ 4.875012] random: jshn: uninitialized urandom read (4 bytes read) [ 4.921856] random: jshn: uninitialized urandom read (4 bytes read) [ 8.512920] jffs2: notice: (408) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (0 unchecked, 2 orphan) and 7 of xref (2 dead, 0 orphan) found. [ 8.530513] mount_root: switching to jffs2 overlay [ 8.562085] overlayfs: upper fs does not support tmpfile. [ 8.574308] urandom-seed: Seeding with /etc/urandom.seed [ 8.725811] procd: - early - [ 8.728868] procd: - watchdog - [ 9.454755] procd: - watchdog - [ 9.458302] procd: - ubus - [ 9.623584] urandom_read: 4 callbacks suppressed [ 9.623593] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.637040] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.644082] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.651833] procd: - init - [ 10.160454] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.171508] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7 [ 10.179259] Backport generated by backports.git v4.19.32-1-0-g1c4f7569 [ 10.196508] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 10.280616] xt_time: kernel timezone is -0000 [ 10.474877] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.531749] PPP generic driver version 2.4.2 [ 10.539265] NET: Registered protocol family 24 [ 10.581551] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 10.587529] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 10.869567] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 10.880479] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.077173] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 11.087888] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2 [ 11.098807] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.348875] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed [ 11.375196] ath10k_pci 0000:00:00.0: qca988x hw2.0 ubiquiti target 0x4100016c chip_id 0x043222ff sub 0777:e7f9 [ 11.385397] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 11.400308] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00043 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 ed0aafd8 [ 11.494908] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 [ 11.505553] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.683454] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 11.704240] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 12.851633] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 12.996812] ath: EEPROM regdomain: 0x0 [ 12.996821] ath: EEPROM indicates default country code should be used [ 12.996825] ath: doing EEPROM country->regdmn map search [ 12.996843] ath: country maps to regdmn code: 0x3a [ 12.996850] ath: Country alpha2 being used: US [ 12.996854] ath: Regpair used: 0x3a [ 13.165509] ath: phy1: disabling 5GHz band [ 13.170774] ath: EEPROM regdomain: 0x0 [ 13.170780] ath: EEPROM indicates default country code should be used [ 13.170784] ath: doing EEPROM country->regdmn map search [ 13.170802] ath: country maps to regdmn code: 0x3a [ 13.170809] ath: Country alpha2 being used: US [ 13.170814] ath: Regpair used: 0x3a [ 13.187652] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 13.189521] ieee80211 phy1: Atheros AR9340 Rev:3 mem=0xb8100000, irq=12 [ 13.200935] kmodloader: done loading kernel modules from /etc/modules.d/* [ 26.857758] br-lan: port 1(eth0) entered blocking state [ 26.863075] br-lan: port 1(eth0) entered disabled state [ 26.868761] device eth0 entered promiscuous mode [ 32.906003] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware [ 32.950174] br-lan: port 2(wlan0) entered blocking state [ 32.955650] br-lan: port 2(wlan0) entered disabled state [ 32.961396] device wlan0 entered promiscuous mode [ 34.079289] br-lan: port 2(wlan0) entered blocking state [ 34.084764] br-lan: port 2(wlan0) entered listening state [ 35.610933] br-lan: port 3(wlan0.sta1) entered blocking state [ 35.616843] br-lan: port 3(wlan0.sta1) entered disabled state [ 35.623013] device wlan0.sta1 entered promiscuous mode [ 35.651821] br-lan: port 3(wlan0.sta1) entered blocking state [ 35.657734] br-lan: port 3(wlan0.sta1) entered listening state [ 36.114646] br-lan: port 2(wlan0) entered learning state [ 37.714627] br-lan: port 3(wlan0.sta1) entered learning state [ 38.194637] br-lan: port 2(wlan0) entered forwarding state [ 38.200220] br-lan: topology change detected, sending tcn bpdu [ 39.794628] br-lan: port 3(wlan0.sta1) entered forwarding state [ 39.800650] br-lan: topology change detected, sending tcn bpdu