TP-Link TL-MR12U

This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 4/32 warning for details.

1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.

2) OpenWrt support for this device has ended in 2022.
19.07.10 was the last official build for 4/32 devices.

A portable_router with an onboard 5200mAh battery. See also TL-MR10U, TL-MR11U, TL-MR13U or TL-MR3020, TL-MR3040 and TL-WR703N.

Note: Many of these routers are marketed as a “3G travel router” but none actually include a 3G modem - the marketing term rather means that the OEM firmware supports USB 3G modems because it contains drivers for USB modems! Ignore that, because with OpenWrt ANY router with USB supports 3G hardware...

Price: AliExpress - about 35 USD

Supported Versions

Hardware Highlights

Installation

Please consult → Install OpenWrt (generic explanation) and also TL-WR703N and TL-MR3020.

Flash Layout

Please check out the article flash.layout. It contains an example and a couple of explanations.

OEM easy installation

The instructions below are for Broadcom devices and only serve as an example. Don't leave them in place if they do not apply to a particular device!

This section deals with how you install OpenWrt from a device freshly opened. Plus the steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

Browse to http://192.168.1.1/Upgrade.asp
Upload .bin file to router
Wait for it to reboot
Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

OEM installation using the TFTP method

→ generic.flashing.tftp

Specific values you need

Bootloader tftp server IPv4 address	FILL-IN
Bootloader MAC address (special)	FILL-IN
Firmware tftp image	http://downloads.openwrt.org/FILL-IN/openwrt-FILL-IN-generic-FILL-IN-squashfs-tftp.bin (`NOTE:` Name must contain “tftp”)
TFTP Transfer Window	FILL-IN seconds
TFTP Window Start	approximately FILL-IN seconds after power on
TFTP Client Required IP Address	FILL-IN

Upgrading OpenWrt

→ generic.sysupgrade

LuCI Web Upgrade Process

Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
Upload image file for sysupgrade to LuCI
Wait for reboot

Terminal Upgrade Process

Use the following commands to upgrade

cd /tmp/
wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

If sysupgrade does not support this router, use the following commands

cd /tmp/
wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	LAN & WiFi	192.168.1.1/24
vlan0 (eth0.0)	LAN ports (1 to 4)	None
vlan1 (eth0.1)	WAN port	DHCP
wl0	WiFi	Disabled

Switch Ports (for VLANs)

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	4
LAN 1	3
LAN 2	2
LAN 3	1
LAN 4	0

Failsafe mode

→ failsafe_and_factory_reset

Buttons

→ hardware.button on howto use and configure the hardware button(s).

The Linksys WRT54GL has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto:

BUTTON	Event
Reset	reset
Secure Easy Setup	ses

Hardware

Info

Architecture	MIPS
Vendor	Qualcomm Atheros
bootloader	U-Boot
System-On-Chip	AR9132 rev 2 (MIPS 24Kc V7.4)
CPU/Speed	24Kc V7.4 400 MHz
Flash-Chip	Spansion FL032PIF 32Mbit
Flash size	4 MiB
RAM-Chip	Zintel A3S56D40FTP 252Mbit
RAM	32 MiB
Wireless	Atheros AR9103 2.4GHz 802.11bgn
Ethernet	Atheros 10/100
Internet	n/a (via external dongle: 3g/LTE)
USB	Yes 1 x 2.0, 1x MicroUSB for battery charging/power supply
Serial	Yes
JTAG	Yes
Battery	Li-ion 18650 LGABB41865

Photos

Front:

Back:

Opening the case

Note: This will void your warranty!

The casing is glued on the edges and its hard to open. Be careful, PCB is screwed to smaller part of the housing.

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Photo of PCB with markings

Debricking

→ generic.debrick

Bootloader Mods

Read about bootloader in general and about Das U-Boot in particular.

U-Boot 1.1.4 modification for routers

Forum member pepe2k made a modification of U-Boot 1.1.4 for Qualcomm Atheros SoCs based devices (the project is still being developed, so new devices and SoCs will be supported in the future). Up to date information, binary images and sources can be found on official GitHub repository.

This modification started from wr703n-uboot-with-web-failsafe project, but supports more devices, all modern web browsers, has a lot of improvements and other modifications (like U-Boot NetConsole, custom commands, overclocking possibilities etc.).

More information:

Official repository on GitHub: U-Boot 1.1.4 modification for routers
Discussion about this project on OpenWrt forum
An article (in Polish) about one of the first version of this project on www.tech-blog.pl

Bootlogs

OEM bootlog

PUT HERE YOUR BOOTLOG

OpenWrt bootlog

[ 0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Wed Jul 3 21:27:19 CEST 2013 [ 0.000000] MyLoader: sysp=fa89c804, boardp=69cd3b24, parts=31a09c82 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 802fdda0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8128 pages, LIFO batch:0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=TL-MR3040 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 28940k/32768k available (2255k kernel code, 3828k reserved, 425k data, 216k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79 [ 0.100000] MIPS: machine is TP-LINK TL-MR3040 [ 0.350000] bio: create slab <bio-0> at 0 [ 0.360000] Switching to clocksource MIPS [ 0.370000] NET: Registered protocol family 2 [ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.370000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.380000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.390000] TCP reno registered [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] NET: Registered protocol family 1 [ 0.410000] PCI: CLS 0 bytes, default 32 [ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.440000] msgmni has been set to 56 [ 0.440000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.450000] io scheduler noop registered [ 0.450000] io scheduler deadline registered (default) [ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART [ 0.480000] console [ttyATH0] enabled, bootconsole disabled [ 0.490000] m25p80 spi0.0: found en25q32b, expected m25p80 [ 0.490000] m25p80 spi0.0: en25q32b (4096 Kbytes) [ 0.500000] 5 tp-link partitions found on MTD device spi0.0 [ 0.510000] Creating 5 MTD partitions on "spi0.0": [ 0.510000] 0x000000000000-0x000000020000 : "u-boot" [ 0.520000] 0x000000020000-0x00000010ece4 : "kernel" [ 0.520000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.530000] 0x00000010ece4-0x0000003f0000 : "rootfs" [ 0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.550000] mtd: partition "rootfs" set to be root filesystem [ 0.560000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=60000 [ 0.570000] 0x000000390000-0x0000003f0000 : "rootfs_data" [ 0.570000] 0x0000003f0000-0x000000400000 : "art" [ 0.580000] 0x000000020000-0x0000003f0000 : "firmware" [ 0.600000] ag71xx_mdio: probed [ 0.610000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.160000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.170000] TCP cubic registered [ 1.170000] NET: Registered protocol family 17 [ 1.170000] Bridge firewalling registered [ 1.180000] Ebtables v2.0 registered [ 1.180000] 8021q: 802.1Q VLAN Support v1.8 [ 1.190000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.200000] Freeing unused kernel memory: 216k freed [ 3.500000] Registered led device: tp-link:green:3g [ 3.500000] Registered led device: tp-link:green:wlan [ 3.500000] Registered led device: tp-link:green:lan [ 6.830000] JFFS2 notice: (440) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 40 of xref (0 dead, 26 orphan) found. [ 7.620000] SCSI subsystem initialized [ 7.850000] usbcore: registered new interface driver usbfs [ 7.850000] usbcore: registered new interface driver hub [ 7.860000] usbcore: registered new device driver usb [ 8.190000] eth0: link up (100Mbps/Full duplex) [ 8.430000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.440000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 8.440000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 8.480000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 8.500000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 8.500000] hub 1-0:1.0: USB hub found [ 8.500000] hub 1-0:1.0: 1 port detected [ 8.570000] Initializing USB Mass Storage driver... [ 8.570000] usbcore: registered new interface driver usb-storage [ 8.580000] USB Mass Storage support registered. [ 28.960000] eth0: link down [ 29.560000] Compat-drivers backport release: compat-drivers-2013-01-21-1 [ 29.570000] Backport based on wireless-testing.git master-2013-02-22 [ 29.570000] compat.git: wireless-testing.git [ 29.750000] cfg80211: Calling CRDA to update world regulatory domain [ 29.750000] cfg80211: World regulatory domain updated: [ 29.760000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 29.770000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 29.770000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 30.770000] ath: EEPROM regdomain: 0x0 [ 30.770000] ath: EEPROM indicates default country code should be used [ 30.770000] ath: doing EEPROM country->regdmn map search [ 30.770000] ath: country maps to regdmn code: 0x3a [ 30.770000] ath: Country alpha2 being used: US [ 30.770000] ath: Regpair used: 0x3a [ 30.780000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 30.790000] Registered led device: ath9k-phy0 [ 30.790000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 30.790000] cfg80211: Calling CRDA for country: US [ 30.800000] cfg80211: Regulatory domain changed to country: US [ 30.800000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 30.810000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 30.820000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 31.060000] PPP generic driver version 2.4.2 [ 31.150000] tun: Universal TUN/TAP device driver, 1.6 [ 31.150000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 31.270000] GRE over IPv4 demultiplexor driver [ 31.290000] ip_gre: Unknown symbol icmpv6_send (err 0) [ 31.420000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 32.020000] NET: Registered protocol family 24 [ 32.170000] nf_conntrack version 0.5.0 (455 buckets, 1820 max) [ 32.590000] PPTP driver version 0.8.5 [ 33.360000] xt_time: kernel timezone is -0000 [ 34.250000] Hooked IMQ after mangle on PREROUTING [ 34.250000] Hooked IMQ after nat on POSTROUTING [ 34.260000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1) [ 34.490000] Netfilter messages via NETLINK v0.30. [ 34.550000] ip_set: protocol 6 [ 35.300000] usbcore: registered new interface driver cdc_acm [ 35.300000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 35.460000] usbcore: registered new interface driver usbserial [ 35.470000] USB Serial support registered for generic [ 35.470000] usbcore: registered new interface driver usbserial_generic [ 35.480000] usbserial: USB Serial Driver core [ 35.530000] usbcore: registered new interface driver cdc_ether [ 35.620000] usbcore: registered new interface driver cdc_ncm [ 35.730000] USB Serial support registered for GSM modem (1-port) [ 35.740000] usbcore: registered new interface driver option [ 35.740000] option: v0.7.2:USB Driver for GSM modems [ 35.870000] USB Serial support registered for Sierra USB modem [ 35.880000] usbcore: registered new interface driver sierra [ 35.880000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems [ 40.720000] device eth0 entered promiscuous mode [ 41.460000] eth0: link up (100Mbps/Full duplex) [ 41.460000] br-lan: port 1(eth0) entered forwarding state [ 41.470000] br-lan: port 1(eth0) entered forwarding state [ 43.470000] br-lan: port 1(eth0) entered forwarding state [ 62.710000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting [ 62.720000] old minutes west=0, new minutes west=-60

Notes

OpenWrt trunk r44407 (local patched) bootlog

Linux version 3.14.32 (dani@c1037u) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44398) ) #4 Wed Feb 11 16:28:30 EET 2015 MyLoader: sysp=fa89c804, boardp=69cd3b24, parts=31a09c82 bootconsole [early0] enabled CPU0 revision is: 00019374 (MIPS 24Kc) SoC: Atheros AR9330 rev 1 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Zone ranges: Normal [mem 0x00000000-0x01ffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x01ffffff] On node 0 totalpages: 8192 free_area_init_node: node 0, pgdat 802bc400, node_mem_map 81000000 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8192 pages, LIFO batch:0 Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: board=TL-MR13U console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd PID hash table entries: 128 (order: -3, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 29120K/32768K available (2138K kernel code, 115K rwdata, 240K rodata, 248K init, 182K bss, 3648K reserved) SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:51 Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) NET: Registered protocol family 16 MIPS: machine is TP-LINK TL-MR13U v1 bio: create slab <bio-0> at 0 Switched to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 PCI: CLS 0 bytes, default 32 futex hash table entries: 256 (order: -1, 3072 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. msgmni has been set to 56 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART console [ttyATH0] enabled bootconsole [early0] disabled m25p80 spi0.0: found s25sl032p, expected m25p80 m25p80 spi0.0: s25sl032p (4096 Kbytes) 5 tp-link partitions found on MTD device spi0.0 Creating 5 MTD partitions on "spi0.0": 0x000000000000-0x000000020000 : "u-boot" 0x000000020000-0x000000100584 : "kernel" mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 0x000000100584-0x0000003f0000 : "rootfs" mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only mtd: device 2 (rootfs) set to be root filesystem 1 squashfs-split partitions found on MTD device rootfs 0x000000350000-0x0000003f0000 : "rootfs_data" 0x0000003f0000-0x000000400000 : "art" 0x000000020000-0x0000003f0000 : "firmware" libphy: ag71xx_mdio: probed ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 248K (802d2000 - 80310000) usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb SCSI subsystem initialized ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-platform: EHCI generic platform driver ehci-platform ehci-platform: EHCI Host Controller ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 ehci-platform ehci-platform: irq 3, io mem 0x1b000000 ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform: OHCI generic platform driver usbcore: registered new interface driver usb-storage random: mktemp urandom read with 76 bits of entropy available jffs2: notice: (321) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. jffs2: notice: (318) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. random: nonblocking pool is initialized NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver ip6_tables: (C) 2000-2006 Netfilter Core Team usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver cdc_wdm Loading modules backported from Linux version master-2014-11-04-0-gf3660a2 Backport generated by backports.git backports-20141023-2-g4ff890b ip_tables: (C) 2000-2006 Netfilter Core Team usbcore: registered new interface driver ipheth nf_conntrack version 0.5.0 (458 buckets, 1832 max) usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic xt_time: kernel timezone is -0000 usbcore: registered new interface driver ark3116 usbserial: USB Serial support registered for ark3116 usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver cdc_subset cfg80211: Calling CRDA to update world regulatory domain cfg80211: World regulatory domain updated: cfg80211: DFS Master region: unset cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) usbcore: registered new interface driver cp210x usbserial: USB Serial support registered for cp210x usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver huawei_cdc_ncm usbcore: registered new interface driver pl2303 usbserial: USB Serial support registered for pl2303 PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 usbcore: registered new interface driver qmi_wwan usbcore: registered new interface driver rndis_host usbcore: registered new interface driver sierra usbserial: USB Serial support registered for Sierra USB modem usbcore: registered new interface driver sierra_net usbcore: registered new interface driver cdc_mbim usbcore: registered new interface driver ipw usbserial: USB Serial support registered for IPWireless converter usbcore: registered new interface driver option usbserial: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver qcserial usbserial: USB Serial support registered for Qualcomm USB modem ath: EEPROM regdomain: 0x0 ath: EEPROM indicates default country code should be used ath: doing EEPROM country->regdmn map search ath: country maps to regdmn code: 0x3a ath: Country alpha2 being used: US ath: Regpair used: 0x3a ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' cfg80211: Calling CRDA for country: US cfg80211: Regulatory domain changed to country: US cfg80211: DFS Master region: FCC cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A) cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready device eth0 entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready cfg80211: Calling CRDA for country: RO cfg80211: Regulatory domain changed to country: RO cfg80211: DFS Master region: ETSI cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s) cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready device wlan0 entered promiscuous mode br-lan: port 2(wlan0) entered forwarding state br-lan: port 2(wlan0) entered forwarding state IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready br-lan: port 2(wlan0) entered forwarding state

Table of Contents