NETGEAR R6350

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE

[ 0.000000] Linux version 5.15.134 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23497-6637af95aa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Oct 9 21:45:35 2023 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Netgear R6350 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 11 pages/cpu s14736 r8192 d22128 u45056 [ 0.000000] pcpu-alloc: s14736 r8192 d22128 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00041800 [ 0.000000] Readback ErrCtl register=00041800 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 119284K/131072K available (7298K kernel code, 626K rwdata, 880K rodata, 1232K init, 226K bss, 11788K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.016033] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.088335] pid_max: default: 32768 minimum: 301 [ 0.098284] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.112701] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.131885] rcu: Hierarchical SRCU implementation. [ 0.142104] smp: Bringing up secondary CPUs ... [ 0.151875] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.151902] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.151917] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.151961] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.211644] Synchronize counters for CPU 1: done. [ 0.273851] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.273876] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.273886] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.273912] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.332824] Synchronize counters for CPU 2: done. [ 0.393231] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.393253] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.393264] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.393296] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.452398] Synchronize counters for CPU 3: done. [ 0.511996] smp: Brought up 1 node, 4 CPUs [ 0.526085] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545581] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.559484] pinctrl core: initialized pinctrl subsystem [ 0.571390] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.583896] thermal_sys: Registered thermal governor 'step_wise' [ 0.590510] FPU Affinity set after 11720 emulations [ 0.615507] clocksource: Switched to clocksource GIC [ 0.626795] NET: Registered PF_INET protocol family [ 0.636570] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.651732] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.668283] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.683631] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.698844] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.712836] TCP: Hash tables configured (established 1024 bind 1024) [ 0.725657] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.738556] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.752733] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.763940] PCI: CLS 0 bytes, default 32 [ 0.774607] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.792917] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.804466] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.825230] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.843682] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.855168] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.866616] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.878159] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 0.891425] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 0.908878] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000 [ 0.925146] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 1.295577] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.309341] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.319003] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.328698] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.342838] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.355359] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.366239] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.379882] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.392197] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.404091] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.416535] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff] [ 1.429027] pci 0000:00:00.0: supports D1 [ 1.436907] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.449225] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.461120] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.473525] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff] [ 1.486041] pci 0000:00:01.0: supports D1 [ 1.493885] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.507805] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 1.519713] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 1.533307] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.564406] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.574717] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.586782] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.600265] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.614618] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.628039] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 [ 1.639919] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 1.652444] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 1.666206] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.676512] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.688594] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 1.702070] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 1.716411] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.729591] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.742681] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.756513] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 1.769631] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.783456] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.796940] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 1.811280] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 1.824762] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 1.839097] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 1.852585] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 1.866068] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff] [ 1.878163] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.890252] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 1.904775] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.914609] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.926712] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.940195] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.954533] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] [ 1.968008] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.977861] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff] [ 1.989950] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 2.003441] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 2.020254] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 2.037730] printk: console [ttyS0] disabled [ 2.046297] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 2.064231] printk: console [ttyS0] enabled [ 2.080761] printk: bootconsole [early0] disabled [ 2.103152] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 2.115887] nand: Macronix MX30LF1G18AC [ 2.123511] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.138625] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 2.209018] scpart: Valid 'SC PART MAP' (29 partitions) found at 0x100000 [ 2.222689] 29 scpart partitions found on MTD device mt7621-nand [ 2.235239] Creating 29 MTD partitions on "mt7621-nand": [ 2.245875] 0x000000000000-0x000000100000 : "u-boot" [ 2.267109] 0x000000100000-0x000000200000 : "SC PART_MAP" [ 2.289166] 0x000000200000-0x000000600000 : "kernel" [ 2.340468] 0x000000600000-0x000002e00000 : "ubi" [ 2.753137] 0x000002e00000-0x000003000000 : "English UI" [ 2.785080] 0x000003000000-0x000003200000 : "ML1" [ 2.815724] 0x000003200000-0x000003440000 : "ML2" [ 2.847562] 0x000003440000-0x000003640000 : "ML3" [ 2.878234] 0x000003640000-0x000003840000 : "ML4" [ 2.908970] 0x000003840000-0x000003a40000 : "ML5" [ 2.939602] 0x000003a40000-0x000003c40000 : "ML6" [ 2.970205] 0x000003c40000-0x000003e40000 : "ML7" [ 3.000801] 0x000003e40000-0x000004040000 : "ML8" [ 3.031310] 0x000004040000-0x000004240000 : "ML9" [ 3.061876] 0x000004240000-0x000004440000 : "ML10" [ 3.092727] 0x000004440000-0x000004640000 : "ML11" [ 3.123548] 0x000004640000-0x000004840000 : "factory" [ 3.154825] 0x000004840000-0x000004a40000 : "SC Private Data" [ 3.187595] 0x000004a40000-0x000004c40000 : "POT" [ 3.218311] 0x000004c40000-0x000004e40000 : "Traffic Meter" [ 3.250712] 0x000004e40000-0x000005040000 : "SC PID" [ 3.282017] 0x000005040000-0x000005240000 : "SC Nvram" [ 3.313447] 0x000005240000-0x000005440000 : "Ralink Nvram" [ 3.345663] 0x000005440000-0x000005640000 : "reserved0" [ 3.377266] 0x000005640000-0x000005840000 : "reserved1" [ 3.408970] 0x000005840000-0x000005a40000 : "reserved2" [ 3.440596] 0x000005a40000-0x000005c40000 : "reserved3" [ 3.472482] 0x000005c40000-0x000005e40000 : "reserved4" [ 3.504207] 0x000005e40000-0x000007f80000 : "reserved5" [ 3.999167] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module [ 4.019596] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 4.039788] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21 [ 4.058169] i2c_dev: i2c /dev entries driver [ 4.070015] NET: Registered PF_INET6 protocol family [ 4.082387] Segment Routing with IPv6 [ 4.089806] In-situ OAM (IOAM) with IPv6 [ 4.097762] NET: Registered PF_PACKET protocol family [ 4.107967] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.134266] 8021q: 802.1Q VLAN Support v1.8 [ 4.149617] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module [ 4.182032] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode [ 4.196647] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 4.206356] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=23) [ 4.234962] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=24) [ 4.257967] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=25) [ 4.280951] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=26) [ 4.303854] DSA: tree 0 setup [ 4.312895] UBI: auto-attach mtd3 [ 4.319603] ubi0: attaching mtd3 [ 5.132024] ubi0: scanning is finished [ 5.156102] ubi0: attached mtd3 (name "ubi", size 40 MiB) [ 5.166926] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.180636] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.194159] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.208029] ubi0: good PEBs: 320, bad PEBs: 0, corrupted PEBs: 0 [ 5.219995] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 5.234397] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1696887935 [ 5.252594] ubi0: available PEBs: 0, total reserved PEBs: 320, PEBs reserved for bad PEB handling: 20 [ 5.270985] ubi0: background thread "ubi_bgt0d" started, PID 427 [ 5.273552] block ubiblock0_0: created from ubi0:0(rootfs) [ 5.293966] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 5.316647] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 5.334910] Freeing unused kernel image (initmem) memory: 1232K [ 5.346789] This architecture does not have kernel memory protection. [ 5.359636] Run /sbin/init as init process [ 5.367802] with arguments: [ 5.367809] /sbin/init [ 5.367816] with environment: [ 5.367820] HOME=/ [ 5.367826] TERM=linux [ 5.863820] init: Console is alive [ 5.871198] init: - watchdog - [ 6.710084] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.775398] usbcore: registered new interface driver usbfs [ 6.786563] usbcore: registered new interface driver hub [ 6.797369] usbcore: registered new device driver usb [ 6.818496] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 6.834075] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 6.844787] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 6.864889] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 6.883224] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 6.894959] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 6.905602] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 6.920533] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 6.934310] hub 1-0:1.0: USB hub found [ 6.941955] hub 1-0:1.0: 2 ports detected [ 6.951073] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.968360] hub 2-0:1.0: USB hub found [ 6.976033] hub 2-0:1.0: 1 port detected [ 6.991929] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 7.016685] init: - preinit - [ 7.817005] random: jshn: uninitialized urandom read (4 bytes read) [ 7.941859] random: jshn: uninitialized urandom read (4 bytes read) [ 7.992098] random: jshn: uninitialized urandom read (4 bytes read) [ 8.304376] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 8.324800] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 8.325947] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 8.356233] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.557985] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 10.569634] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 576 [ 10.650156] UBIFS (ubi0:1): recovery needed [ 10.860549] UBIFS (ubi0:1): recovery completed [ 10.869595] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 10.885213] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.904968] UBIFS (ubi0:1): FS size: 31870976 bytes (30 MiB, 251 LEBs), max 261 LEBs, journal size 1650688 bytes (1 MiB, 13 LEBs) [ 10.928186] UBIFS (ubi0:1): reserved for root: 1505344 bytes (1470 KiB) [ 10.941369] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D77631B8-700F-4D70-92CE-C7A2B02E1CCA, small LPT model [ 10.970728] mount_root: switching to ubifs overlay [ 10.998860] urandom-seed: Seeding with /etc/urandom.seed [ 11.113244] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 11.129140] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 11.144693] mt7530-mdio mdio-bus:1f lan1: Link is Down [ 11.164321] procd: - early - [ 11.170402] procd: - watchdog - [ 11.823902] procd: - watchdog - [ 11.834263] procd: - ubus - [ 11.920895] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.936212] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.949485] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.970231] procd: - init - [ 12.661049] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.863401] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b [ 12.878391] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36 [ 13.087696] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 13.099101] mt7603e 0000:02:00.0: enabling device (0000 -> 0002) [ 13.111349] mt7603e 0000:02:00.0: ASIC revision: 76030010 [ 13.721031] urngd: v1.0.2 started. [ 14.139213] mt7603e 0000:02:00.0: Firmware Version: ap_pcie [ 14.150444] mt7603e 0000:02:00.0: Build Time: 20160107100755 [ 14.183307] mt7603e 0000:02:00.0: firmware init done [ 14.372520] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 14.384908] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 14.396271] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 14.427162] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 14.427222] ieee80211 phy1: copying sband (band 1) due to VHT EXT NSS BW flag [ 14.503059] PPP generic driver version 2.4.2 [ 14.516419] random: crng init done [ 14.516985] NET: Registered PF_PPPOX protocol family [ 14.523267] random: 31 urandom warning(s) missed due to ratelimiting [ 14.548994] kmodloader: done loading kernel modules from /etc/modules.d/* [ 14.562769] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 14.562769] [ 14.875165] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 15.023906] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149 [ 22.474246] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 22.505145] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 22.521907] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 22.538857] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 22.557473] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 22.573616] br-lan: port 1(lan1) entered blocking state [ 22.584250] br-lan: port 1(lan1) entered disabled state [ 22.597590] device lan1 entered promiscuous mode [ 22.606916] device eth0 entered promiscuous mode [ 22.658946] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode [ 22.676402] br-lan: port 2(lan2) entered blocking state [ 22.686959] br-lan: port 2(lan2) entered disabled state [ 22.700421] device lan2 entered promiscuous mode [ 22.725071] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode [ 22.741340] br-lan: port 3(lan3) entered blocking state [ 22.751951] br-lan: port 3(lan3) entered disabled state [ 22.765221] device lan3 entered promiscuous mode [ 22.790716] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode [ 22.807128] br-lan: port 4(lan4) entered blocking state [ 22.817620] br-lan: port 4(lan4) entered disabled state [ 22.831896] device lan4 entered promiscuous mode [ 22.861762] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:04] driver [MediaTek MT7530 PHY] (irq=POLL) [ 22.880801] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode [ 24.502836] br-lan: port 5(phy0-ap0) entered blocking state [ 24.514185] br-lan: port 5(phy0-ap0) entered disabled state [ 24.526117] device phy0-ap0 entered promiscuous mode [ 24.561956] br-lan: port 5(phy0-ap0) entered blocking state [ 24.573224] br-lan: port 5(phy0-ap0) entered forwarding state [ 24.587778] br-lan: port 5(phy0-ap0) entered disabled state [ 24.995284] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 25.676596] mt7530-mdio mdio-bus:1f lan2: Link is Up - 100Mbps/Full - flow control rx/tx [ 26.115202] br-lan: port 1(lan1) entered blocking state [ 26.125711] br-lan: port 1(lan1) entered forwarding state [ 26.137492] br-lan: port 2(lan2) entered blocking state [ 26.147983] br-lan: port 2(lan2) entered forwarding state [ 26.159071] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 26.172808] br-lan: port 6(phy1-ap0) entered blocking state [ 26.183992] br-lan: port 6(phy1-ap0) entered disabled state [ 26.195620] device phy1-ap0 entered promiscuous mode [ 28.539840] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready [ 28.553450] br-lan: port 6(phy1-ap0) entered blocking state [ 28.564645] br-lan: port 6(phy1-ap0) entered forwarding state [ 33.099066] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready [ 33.112759] br-lan: port 5(phy0-ap0) entered blocking state [ 33.124004] br-lan: port 5(phy0-ap0) entered forwarding state