GL.iNet GL-E750 (Mudi)

[ 0.000000] Linux version 4.14.221 (glinet@ubuntu) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11257-5090152ae3)) #0 Mon Feb 15 15:22:37 2021 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] MIPS: machine is GL.iNet GL-E750 (NOR/NAND) [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 805d3a90, node_mem_map 810072e0 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x494 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: rootfstype=squashfs,jffs2 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 122404K/131072K available (4419K kernel code, 160K rwdata, 1008K rodata, 1252K init, 218K bss, 8668K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 650.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008247] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.074858] pid_max: default: 32768 minimum: 301 [ 0.079928] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.086906] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.098372] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.108789] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.115312] pinctrl core: initialized pinctrl subsystem [ 0.121987] NET: Registered protocol family 16 [ 0.133610] PCI host bridge /ahb/pcie-controller@180c0000 ranges: [ 0.140049] MEM 0x0000000010000000..0x0000000013ffffff [ 0.145599] IO 0x0000000000000000..0x0000000000000000 [ 0.167159] PCI host bridge to bus 0000:00 [ 0.171492] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.178782] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.184653] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.191811] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.200194] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000 [ 0.200252] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.200305] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.200381] pci 0000:00:00.0: supports D1 [ 0.200389] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.200599] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.200625] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.208380] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.218569] clocksource: Switched to clocksource MIPS [ 0.224892] NET: Registered protocol family 2 [ 0.230381] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.237734] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.244497] TCP: Hash tables configured (established 1024 bind 1024) [ 0.251358] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.257524] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.264437] NET: Registered protocol family 1 [ 0.269114] PCI: CLS 0 bytes, default 32 [ 0.271896] Crashlog allocated RAM at address 0x3f00000 [ 0.278722] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.290504] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.296645] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.317150] io scheduler noop registered [ 0.321345] io scheduler deadline registered (default) [ 0.328912] pinctrl-single 1804002c.pinmux: 576 pins at pa b804002c size 72 [ 0.336758] gpio-export gpio-export: 1 gpio(s) exported [ 0.343024] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.352072] console [ttyS0] disabled [ 0.355882] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.365027] console [ttyS0] enabled [ 0.448600] bootconsole [early0] disabled [ 0.561574] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.618065] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.694272] Creating 5 MTD partitions on “spi0.0”: [ 0.751763] 0x000000000000-0x000000040000 : “u-boot” [ 0.812113] 0x000000040000-0x000000050000 : “u-boot-env” [ 0.876612] 0x000000050000-0x000000060000 : “art” [ 0.933831] 0x000000060000-0x000000260000 : “kernel” [ 0.994128] 0x000000260000-0x000000e20000 : “nor_reserved” [ 1.064002] spi-nand: Giga SPI NAND was found. [ 1.117333] spi-nand: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 [ 1.208248] 1 fixed-partitions partitions found on MTD device spi0.1 [ 1.284525] Creating 1 MTD partitions on “spi0.1”: [ 1.342004] 0x000000000000-0x000008000000 : “ubi” [ 1.826946] found bad block 7fe0000 [ 1.869504] libphy: Fixed MDIO Bus: probed [ 2.258960] libphy: ag71xx_mdio: probed [ 2.589041] mdio-bus.0:1f: Found an AR934X built-in switch [ 2.655047] libphy: ar7240sw_mdio: probed [ 3.090791] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd042, driver=Generic PHY] [ 3.205249] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii [ 3.278953] NET: Registered protocol family 10 [ 3.335833] Segment Routing with IPv6 [ 3.379915] NET: Registered protocol family 17 [ 3.433251] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.588744] 8021q: 802.1Q VLAN Support v1.8 [ 3.644664] UBI: auto-attach mtd5 [ 3.684460] ubi0: attaching mtd5 [ 4.158571] random: fast init done [ 8.042887] ubi0: scanning is finished [ 8.135938] ubi0: attached mtd5 (name “ubi”, size 128 MiB) [ 8.201811] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 8.284293] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 8.365758] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 8.449317] ubi0: good PEBs: 1023, bad PEBs: 1, corrupted PEBs: 0 [ 8.522446] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 8.609139] ubi0: max/mean erase counter: 95/41, WL threshold: 4096, image sequence number: 966606896 [ 8.719821] ubi0: available PEBs: 0, total reserved PEBs: 1023, PEBs reserved for bad PEB handling: 19 [ 8.831642] ubi0: background thread “ubi_bgt0d” started, PID 317 [ 8.906964] block ubiblock0_0: created from ubi0:0(rootfs) [ 8.972845] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 9.075139] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 9.167572] Freeing unused kernel memory: 1252K [ 9.221928] This architecture does not have kernel memory protection. [ 10.247904] init: Console is alive [ 10.289018] init: - watchdog - [ 13.689415] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 13.981702] usbcore: registered new interface driver usbfs [ 14.047662] usbcore: registered new interface driver hub [ 14.111489] usbcore: registered new device driver usb [ 14.183133] exFAT: Version 1.2.9 [ 14.258705] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 14.346521] SCSI subsystem initialized [ 14.397049] ehci-platform: EHCI generic platform driver [ 14.460004] ehci-platform 1b000000.usb: EHCI Host Controller [ 14.528006] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 14.622047] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000 [ 14.718591] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 14.793547] hub 1-0:1.0: USB hub found [ 14.838964] hub 1-0:1.0: 1 port detected [ 14.889686] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 14.965902] ohci-platform: OHCI generic platform driver [ 15.031350] uhci_hcd: USB Universal Host Controller Interface driver [ 15.112648] usbcore: registered new interface driver usb-storage [ 15.187326] usbcore: registered new interface driver uas [ 15.252135] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 15.349318] init: - preinit - [ 15.409066] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 15.800699] hub 1-1:1.0: USB hub found [ 15.856284] hub 1-1:1.0: 4 ports detected [ 16.678252] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 17.007029] random: procd: uninitialized urandom read (4 bytes read) [ 17.083852] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 17.192144] scsi host0: usb-storage 1-1.1:1.0 [ 17.408901] usb 1-1.2: new high-speed USB device number 4 using ehci-platform [ 17.608745] random: jshn: uninitialized urandom read (4 bytes read) [ 17.907381] random: jshn: uninitialized urandom read (4 bytes read) [ 18.015224] random: jshn: uninitialized urandom read (4 bytes read) [ 18.140678] random: jshn: uninitialized urandom read (4 bytes read) [ 18.241132] random: jshn: uninitialized urandom read (4 bytes read) [ 18.318994] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0233 PQ: 0 ANSI: 0 [ 19.167694] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.449505] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 21.311639] eth0: link up (100Mbps/Full duplex) [ 21.367813] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 22.621637] mount_root: loading kmods from internal overlay [ 22.767399] kmodloader: loading kernel modules from etc/modules-boot.d/* [ 22.854710] kmodloader: done loading kernel modules from etc/modules-boot.d/* [ 25.828776] UBIFS (ubi0:1): background thread “ubifs_bgt0_1” started, PID 496 [ 26.157627] UBIFS (ubi0:1): recovery needed [ 26.811696] UBIFS (ubi0:1): recovery completed [ 26.865155] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name “rootfs_data” [ 26.959152] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 27.078170] UBIFS (ubi0:1): FS size: 112246784 bytes (107 MiB, 884 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs) [ 27.205534] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 27.284924] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 7BD9356E-6F9C-4781-AE60-80B252A2D35E, small LPT model [ 27.435298] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 27.555611] block: extroot: not configured [ 27.605036] UBIFS (ubi0:1): un-mount UBI device 0 [ 27.663093] UBIFS (ubi0:1): background thread “ubifs_bgt0_1” stops [ 27.759505] UBIFS (ubi0:1): background thread “ubifs_bgt0_1” started, PID 499 [ 28.331606] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name “rootfs_data” [ 28.425649] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 28.544730] UBIFS (ubi0:1): FS size: 112246784 bytes (107 MiB, 884 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs) [ 28.672090] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 28.751457] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 7BD9356E-6F9C-4781-AE60-80B252A2D35E, small LPT model [ 28.915337] mount_root: loading kmods from internal overlay [ 29.054576] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 29.161700] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 31.170472] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 31.278993] block: extroot: not configured [ 31.339256] mount_root: switching to ubifs overlay [ 31.510923] urandom-seed: Seeding with /etc/urandom.seed [ 31.729177] eth0: link down [ 31.774864] procd: - early - [ 31.809554] procd: - watchdog - [ 32.547101] urandom_read: 2 callbacks suppressed [ 32.547110] random: jshn: uninitialized urandom read (4 bytes read) [ 32.677897] procd: - watchdog - [ 32.786672] procd: - ubus - [ 33.086859] random: ubusd: uninitialized urandom read (4 bytes read) [ 33.407253] procd: - init - [ 37.065053] kmodloader: loading kernel modules from /etc/modules.d/* [ 37.334941] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 37.421574] urngd: v1.0.2 started. [ 37.551524] tun: Universal TUN/TAP device driver, 1.6 [ 37.773789] GobiNet: 2018-12-21/SWI_2.55 [ 37.822317] usbcore: registered new interface driver GobiNet [ 38.064222] random: crng init done [ 38.155166] usbcore: registered new interface driver usbserial [ 38.225309] usbcore: registered new interface driver usbserial_generic [ 38.303721] usbserial: USB Serial support registered for generic [ 38.839890] usbcore: registered new interface driver GobiSerial [ 38.911104] usbserial: USB Serial support registered for GobiSerial [ 38.986321] GobiSerial: 2015-08-27/SWI_2.25:GobiSerial [ 39.611837] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 39.827308] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 40.314578] Netfilter messages via NETLINK v0.30. [ 40.486418] ip_set: protocol 6 [ 40.709987] Mirror/redirect action on [ 40.870000] u32 classifier [ 40.902473] input device check on [ 40.946356] Actions configured [ 41.243440] GACT probability on [ 41.335169] Simple TC action Loaded [ 41.422575] fuse init (API version 7.26) [ 41.483464] usbcore: registered new interface driver cdc_acm [ 41.551497] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 41.651134] usbcore: registered new interface driver cdc_ether [ 41.726236] usbcore: registered new interface driver cdc_ncm [ 41.797089] usbcore: registered new interface driver cdc_wdm [ 41.868006] Loading modules backported from Linux version v4.19.161-0-gdaefdc9eb24b [ 41.959979] Backport generated by backports.git v4.19.161-1-0-g4bb568fe [ 42.042643] usbcore: registered new interface driver cp210x [ 42.109650] usbserial: USB Serial support registered for cp210x [ 42.197251] Ebtables v2.0 registered [ 42.242205] usbcore: registered new interface driver huawei_cdc_ncm [ 42.321802] ip_tables: (C) 2000-2006 Netfilter Core Team [ 42.388383] usbcore: registered new interface driver ipheth [ 42.552155] ctnetlink v0.93: registering with nfnetlink. [ 42.744694] qmi_wwan 1-1.2:1.4: cdc-wdm0: USB WDM device [ 42.808525] qmi_wwan 1-1.2:1.4: QuectelEC25&EC21&EG91&EG95&EG06&EP06&EM06&BG96&AG35 work on RawIP mode [ 42.922329] qmi_wwan 1-1.2:1.4 wwan0: register 'qmi_wwan' at usb-1b000000.usb-1.2, WWAN/QMI device, 06:21:a5:ac:c9:c9 [ 43.049953] usbcore: registered new interface driver qmi_wwan [ 43.124288] usbcore: registered new interface driver rndis_host [ 43.199084] usbcore: registered new interface driver sierra [ 43.266047] usbserial: USB Serial support registered for Sierra USB modem [ 43.352503] usbcore: registered new interface driver sierra_net [ 43.440205] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information. [ 43.541585] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. [ 43.710231] xt_time: kernel timezone is -0000 [ 43.963548] usbcore: registered new interface driver option [ 44.030534] usbserial: USB Serial support registered for GSM modem (1-port) [ 44.114558] option 1-1.2:1.0: GSM modem (1-port) converter detected [ 44.190056] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0 [ 44.273863] option 1-1.2:1.1: GSM modem (1-port) converter detected [ 44.349385] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1 [ 44.433165] option 1-1.2:1.2: GSM modem (1-port) converter detected [ 44.508723] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2 [ 44.592449] option 1-1.2:1.3: GSM modem (1-port) converter detected [ 44.667981] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB3 [ 45.024355] PPP generic driver version 2.4.2 [ 45.081625] PPP MPPE Compression module registered [ 45.141664] NET: Registered protocol family 24 [ 45.253329] PCI: Enabling device 0000:00:00.0 (0000 → 0002) [ 45.323540] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 45.698811] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 45.827218] ath10k_pci 0000:00:00.0: Falling back to user helper [ 51.074293] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 51.193381] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/firmware-6.bin failed with error -2 [ 51.321852] ath10k_pci 0000:00:00.0: Falling back to user helper [ 51.606090] firmware ath10k!QCA9887!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 51.951474] ath10k_pci 0000:00:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000 [ 52.062235] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 52.165867] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,ignore-otp,skip-clock-init,mfp,allows-mesh-bcast crc32 62f7565f [ 52.362536] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/board-2.bin failed with error -2 [ 52.487829] ath10k_pci 0000:00:00.0: Falling back to user helper [ 52.665234] firmware ath10k!QCA9887!hw1.0!board-2.bin: firmware_loading_store: map pages failed [ 52.788427] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 546cca0d [ 53.980237] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 54.220062] ath: EEPROM regdomain: 0x0 [ 54.220070] ath: EEPROM indicates default country code should be used [ 54.220073] ath: doing EEPROM country→regdmn map search [ 54.220086] ath: country maps to regdmn code: 0x3a [ 54.220091] ath: Country alpha2 being used: US [ 54.220094] ath: Regpair used: 0x3a [ 54.351512] usbcore: registered new interface driver rt2800usb [ 54.542600] ath: EEPROM regdomain: 0x0 [ 54.542610] ath: EEPROM indicates default country code should be used [ 54.542613] ath: doing EEPROM country→regdmn map search [ 54.542628] ath: country maps to regdmn code: 0x3a [ 54.542633] ath: Country alpha2 being used: US [ 54.542636] ath: Regpair used: 0x3a [ 54.555521] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 54.557322] ieee80211 phy1: Atheros AR9531 Rev:2 mem=0xb8100000, irq=13 [ 54.723936] kmodloader: done loading kernel modules from /etc/modules.d/* [ 71.943743] IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready [ 73.120879] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 73.129327] br-lan: port 1(eth0) entered blocking state [ 73.129340] br-lan: port 1(eth0) entered disabled state [ 73.129661] device eth0 entered promiscuous mode [ 77.904056] eth0: link up (100Mbps/Full duplex) [ 78.792186] br-lan: port 1(eth0) entered blocking state [ 78.792200] br-lan: port 1(eth0) entered forwarding state [ 86.122910] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware [ 86.239949] br-lan: port 2(wlan0) entered blocking state [ 86.239961] br-lan: port 2(wlan0) entered disabled state [ 86.240296] device wlan0 entered promiscuous mode [ 86.347561] br-lan: port 3(wlan1) entered blocking state [ 86.347575] br-lan: port 3(wlan1) entered disabled state [ 86.347909] device wlan1 entered promiscuous mode [ 88.433427] br-lan: port 3(wlan1) entered blocking state [ 88.433440] br-lan: port 3(wlan1) entered forwarding state [ 88.830507] br-lan: port 2(wlan0) entered blocking state [ 88.830523] br-lan: port 2(wlan0) entered forwarding state