The NanoPi R2S uses the RK3328 SoC. It has two Gbps Ethernet ports and 1G DDR4 RAM. It is a good device for developing IoT applications, NAS applications etc.
Support Forums https://forum.openwrt.org/t/nanopi-r2s-support-forum/220268
None at this time.
The NanoPi R2S has similar specifications to the discontinued Orange Pi R1 Plus, but has a more expensive ethernet chip compared to the “Orange Pi R1 Plus LTS”.
Uncompress the OpenWrt ...sysupgrade.img.gz image and write it to a micro SD card using a tool like dd or Balena Etcher.
More details on → Install OpenWrt (sdcard explanation)
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
→ After flashing, proceed with Basic configuration to set up your Internet connection, configure wireless, configure USB port, etc.
The default network configuration is:
| Interface Name | Description | Default configuration |
|---|---|---|
| eth0 | WAN port | DHCP |
| eth1 | LAN port | static 192.168.1.1 |
→ The FriendlyARM NanoPi R2S has the following buttons:
| BUTTON | Event |
|---|---|
| Reset | reset |
Use hardware.button for howto use and configure the hardware button(s).
If your NanoPi R2S came in a case: * The all-metal case is held by a single philipps screw. * The plastic (usually yellow) case is held together by clips and can be gently pryed apart with a small flat screwdriver or spudger.
→ port.serial general information about the serial port, serial port cable, etc.
For debug purposes (*nix version):
screen /dev/ttyUSB0 1500000 8N1//Note: Debug UART port is 3.3V TTL. Double check that your USB-TTL adapter supports 3.3V. //
//Note: Some USB-TTL adapters, drivers, OSes or terminal programs have trouble operating at 1500000 baud (1.5 Mbaud!) and output garbage even when everything is correct. //
| Serial connection parameters for FriendlyARM NanoPi R2S @@Version@@ | 1500000 8N1 |
|---|
There is a 4 pin fan header which provides 5V at up to 2A of power, depending on the overall power supplied to the R2S.
DDR version 1.16 20190528 ID:0x805 N In DDR4 333MHz Bus Width=32 Col=10 Bank=4 Bank Group=2 Row=15 CS=1 Die Bus-Width=16 Size=768MB ddrconfig:14 OUT Boot1 Release Time: May 13 2019 17:34:36, version: 2.50 ChipType = 0x11, 248 mmc2:cmd1,20 emmc reinit mmc2:cmd1,20 emmc reinit mmc2:cmd1,20 SdmmcInit=2 1 mmc0:cmd5,20 SdmmcInit=0 0 BootCapSize=0 UserCapSize=1920MB FwPartOffset=2000 , 0 run on sd0 StorageInit ok = 32008 Raw SecureMode = 0 SecureInit read PBA: 0x4 SecureInit read PBA: 0x404 SecureInit read PBA: 0x804 SecureInit read PBA: 0xc04 SecureInit read PBA: 0x1004 SecureInit ret = 0, SecureMode = 0 atags_set_bootdev: ret:(0) GPT part: 0, name: uboot, start:0x4000, size:0x2000 GPT part: 1, name: trust, start:0x6000, size:0x2000 GPT part: 2, name: misc, start:0x8000, size:0x2000 GPT part: 3, name: dtbo, start:0xa000, size:0x2000 GPT part: 4, name: resource, start:0xc000, size:0x8000 GPT part: 5, name: kernel, start:0x14000, size:0x14000 GPT part: 6, name: boot, start:0x28000, size:0x18000 GPT part: 7, name: rootfs, start:0x40000, size:0xde000 GPT part: 8, name: userdata, start:0x11e000, size:0xbed43 find part:uboot OK. first_lba:0x4000. find part:trust OK. first_lba:0x6000. LoadTrust Addr:0x6000 No find bl30.bin Load uboot, ReadLba = 4000 Load OK, addr=0x200000, size=0xed0c0 RunBL31 0x40000 NOTICE: BL31: v1.3(release):734d842 NOTICE: BL31: Built : 15:29:53, Dec 26 2019 NOTICE: BL31:Rockchip release version: v1.3 INFO: ARM GICv2 driver initialized INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 1 INFO: plat_rockchip_pmu_init: pd status 0xe INFO: BL31: Initializing runtime services INFO: BL31: Initializing BL32 INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-235-g3b0152ca #231 Fri Mar 13 02:01:39 UTC 2020 aarch64) INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.4 INF [0x0] TEE-CORE:init_teecore:83: teecore inits done INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2017.09-g6923c3aec0 #tzs (Aug 28 2021 - 12:17:12 +0800) Board: NanoPi R2 PreSerial: 2 DRAM: 736 MiB Sysmem: init Relocation Offset: 2dbd6000, fdt: 2bdcb838 Using default environment no mmc device at slot 1 Found IDB in SDcard mmc@ff500000: 1 (SD), mmc@ff520000: 0 Bootdev(atags): mmc 1 MMC1: Legacy, 50Mhz PartType: EFI boot mode: None Found DTB in resource part DTB: rk3328-nanopi-r2-rev00.dtb (64861) ANDROID: fdt overlay OK I2c1 speed: 400000Hz PMIC: RK8050 (on=0x40, off=0x00) vdd_logic init 1075000 uV vdd_arm init 1225000 uV I2c0 speed: 200000Hz CLK: (sync kernel. arm: enter 600000 KHz, init 600000 KHz, kernel 0N/A) apll 400000 KHz dpll 664000 KHz cpll 1200000 KHz gpll 491009 KHz npll 600000 KHz armclk 600000 KHz aclk_bus 150000 KHz hclk_bus 75000 KHz pclk_bus 75000 KHz aclk_peri 150000 KHz hclk_peri 75000 KHz pclk_peri 75000 KHz Net: eth0: ethernet@ff540000 Hit key to stop autoboot('CTRL+C'): 0 ## Booting Rockchip Format Image fdt @ 0x08300000 (0x0000ffae) kernel @ 0x00280000 (0x01e92a00) ramdisk @ 0x0a200000 (0x007233c0) Fdt Ramdisk skip relocation ## Flattened Device Tree blob at 08300000 Booting using the fdt blob at 0x8300000 Using Device Tree in place at 0000000008300000, end 0000000008312fad Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000) Adding bank: 0x0a200000 - 0x30000000 (size: 0x25e00000) Total: 3980.296 ms Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.60 (tzs@tzs-i7pc) (aarch64-linux-gnu-gcc (ctng-1.23.0-150g-FA) 6.4.0, GNU ld (ctng-1.23.0-150g-FA) 2.28) #1 SMP PREEMPT Sat Aug 28 12:07:58 CST 2021 [ 0.000000] Machine model: FriendlyElec NanoPi R2S [ 0.000000] efi: UEFI not found. [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000200000-0x000000002fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000083fffff] [ 0.000000] node 0: [mem 0x000000000a200000-0x000000002fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000002fffffff] [ 0.000000] cma: Reserved 16 MiB at 0x000000002d000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 31 pages/cpu s89576 r8192 d29208 u126976 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 185352 [ 0.000000] Kernel command line: storagemedia=sd androidboot.storagemedia=sd androidboot.mode=normal androidboot.dtbo_idx=1 swiotlb=1 coherent_pool=1m rw root=/dev/mmcblk0p8 rootfstype=ext4 data=/dev/mmcblk0p9 consoleblank=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 677532K/753664K available (14080K kernel code, 2762K rwdata, 4572K rodata, 9792K init, 831K bss, 59748K reserved, 16384K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 46638 entries in 183 pages [ 0.000000] ftrace: allocated 183 pages with 6 groups [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x388/0x508 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001084] Console: colour dummy device 80x25 [ 0.002011] printk: console [tty0] enabled [ 0.002093] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.002161] pid_max: default: 32768 minimum: 301 [ 0.002419] LSM: Security Framework initializing [ 0.002579] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.002625] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.006449] rcu: Hierarchical SRCU implementation. [ 0.008403] EFI services will not be available. [ 0.009479] smp: Bringing up secondary CPUs ... [ 0.010611] Detected VIPT I-cache on CPU1 [ 0.010732] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.012141] Detected VIPT I-cache on CPU2 [ 0.012252] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.013586] Detected VIPT I-cache on CPU3 [ 0.013687] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.013957] smp: Brought up 1 node, 4 CPUs [ 0.014116] SMP: Total of 4 processors activated. [ 0.014149] CPU features: detected: 32-bit EL0 Support [ 0.014182] CPU features: detected: CRC32 instructions [ 0.038460] CPU: All CPU(s) started at EL2 [ 0.038585] alternatives: patching kernel code [ 0.040641] devtmpfs: initialized [ 0.065399] Registered cp15_barrier emulation handler [ 0.065478] Registered setend emulation handler [ 0.065939] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.066004] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.067416] pinctrl core: initialized pinctrl subsystem [ 0.068859] DMI not present or invalid. [ 0.069986] NET: Registered protocol family 16 [ 0.074295] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 0.074940] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.076075] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.076262] audit: initializing netlink subsys (disabled) [ 0.076792] audit: type=2000 audit(0.076:1): state=initialized audit_enabled=0 res=1 [ 0.078334] thermal_sys: Registered thermal governor 'fair_share' [ 0.078349] thermal_sys: Registered thermal governor 'step_wise' [ 0.078991] cpuidle: using governor ladder [ 0.079088] cpuidle: using governor menu [ 0.079850] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.080098] ASID allocator initialised with 65536 entries [ 0.158258] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.158322] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.158357] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.158388] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.161476] cryptd: max_cpu_qlen set to 1000 [ 0.185596] iommu: Default domain type: Translated [ 0.187541] SCSI subsystem initialized [ 0.188533] usbcore: registered new interface driver usbfs [ 0.188660] usbcore: registered new interface driver hub [ 0.188781] usbcore: registered new device driver usb [ 0.188936] mc: Linux media interface: v0.10 [ 0.189016] videodev: Linux video capture interface: v2.00 [ 0.189162] pps_core: LinuxPPS API ver. 1 registered [ 0.189193] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.189257] PTP clock support registered [ 0.190764] Advanced Linux Sound Architecture Driver Initialized. [ 0.192170] Bluetooth: Core ver 2.22 [ 0.192280] NET: Registered protocol family 31 [ 0.192307] Bluetooth: HCI device and connection manager initialized [ 0.192352] Bluetooth: HCI socket layer initialized [ 0.192392] Bluetooth: L2CAP socket layer initialized [ 0.192457] Bluetooth: SCO socket layer initialized [ 0.192517] NetLabel: Initializing [ 0.192543] NetLabel: domain hash size = 128 [ 0.192567] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.192720] NetLabel: unlabeled traffic allowed by default [ 0.194368] clocksource: Switched to clocksource arch_sys_counter [ 1.624067] VFS: Disk quotas dquot_6.6.0 [ 1.624231] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.624537] FS-Cache: Loaded [ 1.642435] NET: Registered protocol family 2 [ 1.642740] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.644889] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes, linear) [ 1.645088] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.645244] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 1.645653] TCP: Hash tables configured (established 8192 bind 8192) [ 1.646036] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) [ 1.646162] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) [ 1.646773] NET: Registered protocol family 1 [ 1.648051] RPC: Registered named UNIX socket transport module. [ 1.648108] RPC: Registered udp transport module. [ 1.648143] RPC: Registered tcp transport module. [ 1.648173] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.648217] PCI: CLS 0 bytes, default 64 [ 1.648644] Trying to unpack rootfs image as initramfs... [ 2.329940] Freeing initrd memory: 7308K [ 2.332305] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 2.341959] Initialise system trusted keyrings [ 2.342633] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 2.358496] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.359444] FS-Cache: Netfs 'nfs' registered for caching [ 2.360506] NFS: Registering the id_resolver key type [ 2.360584] Key type id_resolver registered [ 2.360618] Key type id_legacy registered [ 2.360832] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.360885] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.361348] fuse: init (API version 7.32) [ 2.433286] Key type asymmetric registered [ 2.433351] Asymmetric key parser 'x509' registered [ 2.433474] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.433797] io scheduler mq-deadline registered [ 2.433837] io scheduler kyber registered [ 2.442701] rockchip-u3phy ff470000.usb3-phy: Rockchip u3phy initialized successfully [ 2.450193] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330 [ 2.450259] dma-pl330 ff1f0000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 2.452263] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled [ 2.455908] ff120000.serial: ttyS1 at MMIO 0xff120000 (irq = 20, base_baud = 1500000) is a 16550A [ 2.458129] ff130000.serial: ttyS2 at MMIO 0xff130000 (irq = 21, base_baud = 1500000) is a 16550A [ 2.538559] printk: console [ttyS2] enabled [ 2.543232] random: fast init done [ 2.543924] random: crng init done [ 2.545335] rockchip-drm display-subsystem: [drm:rockchip_drm_platform_probe] *ERROR* No available vop found for display-subsystem. [ 2.561260] brd: module loaded [ 2.584247] loop: module loaded [ 2.588236] libphy: Fixed MDIO Bus: probed [ 2.590960] rk_gmac-dwmac ff540000.ethernet: IRQ eth_wake_irq not found [ 2.591601] rk_gmac-dwmac ff540000.ethernet: IRQ eth_lpi not found [ 2.592412] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock [ 2.593330] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input). [ 2.593991] rk_gmac-dwmac ff540000.ethernet: TX delay(0x24). [ 2.594581] rk_gmac-dwmac ff540000.ethernet: RX delay(0x18). [ 2.595122] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no). [ 2.595812] rk_gmac-dwmac ff540000.ethernet: cannot get clock clk_mac_speed [ 2.596456] rk_gmac-dwmac ff540000.ethernet: clock input from PHY [ 2.602042] rk_gmac-dwmac ff540000.ethernet: init for RGMII [ 2.603038] rk_gmac-dwmac ff540000.ethernet: User ID: 0x10, Synopsys ID: 0x35 [ 2.603721] rk_gmac-dwmac ff540000.ethernet: DWMAC1000 [ 2.604208] rk_gmac-dwmac ff540000.ethernet: DMA HW capability register supported [ 2.604897] rk_gmac-dwmac ff540000.ethernet: RX Checksum Offload Engine supported [ 2.605585] rk_gmac-dwmac ff540000.ethernet: COE Type 2 [ 2.606071] rk_gmac-dwmac ff540000.ethernet: TX Checksum insertion supported [ 2.606763] rk_gmac-dwmac ff540000.ethernet: Wake-Up On Lan supported [ 2.607485] rk_gmac-dwmac ff540000.ethernet: Normal descriptors [ 2.608033] rk_gmac-dwmac ff540000.ethernet: Ring mode enabled [ 2.608575] rk_gmac-dwmac ff540000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.670385] libphy: stmmac: probed [ 2.691073] PPP generic driver version 2.4.2 [ 2.691978] usbcore: registered new interface driver asix [ 2.692566] usbcore: registered new interface driver ax88179_178a [ 2.693198] usbcore: registered new interface driver cdc_ether [ 2.693808] usbcore: registered new interface driver qmi_wwan [ 2.698273] phy phy-ff470000.usb3-phy.2: u3phy u2 power on [ 2.698891] phy phy-ff470000.usb3-phy.3: u3phy u3 power on [ 2.702657] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator [ 2.703646] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator [ 2.834500] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM [ 2.835721] dwc2 ff580000.usb: DWC OTG Controller [ 2.836226] dwc2 ff580000.usb: new USB bus registered, assigned bus number 1 [ 2.836937] dwc2 ff580000.usb: irq 38, io mem 0xff580000 [ 2.837795] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 2.838625] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.839292] usb usb1: Product: DWC OTG Controller [ 2.839728] usb usb1: Manufacturer: Linux 5.10.60 dwc2_hsotg [ 2.840258] usb usb1: SerialNumber: ff580000.usb [ 2.841890] hub 1-0:1.0: USB hub found [ 2.842314] hub 1-0:1.0: 1 port detected [ 2.844786] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.845446] ehci-pci: EHCI PCI platform driver [ 2.845961] ehci-platform: EHCI generic platform driver [ 2.849343] ehci-platform ff5c0000.usb: EHCI Host Controller [ 2.849909] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 2 [ 2.850980] ehci-platform ff5c0000.usb: irq 39, io mem 0xff5c0000 [ 2.866404] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00 [ 2.867463] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 2.868230] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.868897] usb usb2: Product: EHCI Host Controller [ 2.869355] usb usb2: Manufacturer: Linux 5.10.60 ehci_hcd [ 2.869869] usb usb2: SerialNumber: ff5c0000.usb [ 2.871423] hub 2-0:1.0: USB hub found [ 2.871855] hub 2-0:1.0: 1 port detected [ 2.873381] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.874011] ohci-platform: OHCI generic platform driver [ 2.875358] ohci-platform ff5d0000.usb: Generic Platform OHCI controller [ 2.876012] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 3 [ 2.876992] ohci-platform ff5d0000.usb: irq 40, io mem 0xff5d0000 [ 2.938748] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10 [ 2.939521] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.940187] usb usb3: Product: Generic Platform OHCI controller [ 2.940732] usb usb3: Manufacturer: Linux 5.10.60 ohci_hcd [ 2.941238] usb usb3: SerialNumber: ff5d0000.usb [ 2.942774] hub 3-0:1.0: USB hub found [ 2.943211] hub 3-0:1.0: 1 port detected [ 2.945975] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.946596] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4 [ 2.947594] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000020002030010 [ 2.948571] xhci-hcd xhci-hcd.0.auto: irq 47, io mem 0xff600000 [ 2.950011] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 2.950844] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.951516] usb usb4: Product: xHCI Host Controller [ 2.951969] usb usb4: Manufacturer: Linux 5.10.60 xhci-hcd [ 2.952479] usb usb4: SerialNumber: xhci-hcd.0.auto [ 2.954049] hub 4-0:1.0: USB hub found [ 2.954524] hub 4-0:1.0: 1 port detected [ 2.955623] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.956163] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5 [ 2.956887] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.957629] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.958660] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 2.959419] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.960085] usb usb5: Product: xHCI Host Controller [ 2.960538] usb usb5: Manufacturer: Linux 5.10.60 xhci-hcd [ 2.961045] usb usb5: SerialNumber: xhci-hcd.0.auto [ 2.962693] hub 5-0:1.0: USB hub found [ 2.963130] hub 5-0:1.0: 1 port detected [ 2.964527] usbcore: registered new interface driver cdc_acm [ 2.965059] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.965868] usbcore: registered new interface driver cdc_wdm [ 2.967021] usbcore: registered new interface driver uas [ 2.967778] usbcore: registered new interface driver usb-storage [ 2.968530] usbcore: registered new interface driver usbserial_generic [ 2.969171] usbserial: USB Serial support registered for generic [ 2.969805] usbcore: registered new interface driver ch341 [ 2.970403] usbserial: USB Serial support registered for ch341-uart [ 2.971070] usbcore: registered new interface driver cp210x [ 2.971620] usbserial: USB Serial support registered for cp210x [ 2.972343] usbcore: registered new interface driver ftdi_sio [ 2.972916] usbserial: USB Serial support registered for FTDI USB Serial Device [ 2.973973] usbcore: registered new interface driver option [ 2.974555] usbserial: USB Serial support registered for GSM modem (1-port) [ 2.975749] usbcore: registered new interface driver pl2303 [ 2.976300] usbserial: USB Serial support registered for pl2303 [ 2.976955] usbcore: registered new interface driver qcserial [ 2.977524] usbserial: USB Serial support registered for Qualcomm USB modem [ 2.979189] mousedev: PS/2 mouse device common for all mice [ 2.980871] i2c /dev entries driver [ 2.987639] rk808 1-0018: chip id: 0x8050 [ 2.992607] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 2.993242] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 2.994749] vdd_logic: supplied by vcc_sys [ 2.996630] vdd_arm: supplied by vcc_sys [ 2.997635] vcc_ddr: supplied by vcc_sys [ 2.999062] vcc_io: supplied by vcc_sys [ 3.000680] vcc_18: supplied by vcc_io [ 3.003534] vcc18_emmc: supplied by vcc_io [ 3.006314] vdd_10: supplied by vcc_io [ 3.013095] rk808-rtc rk808-rtc: registered as rtc0 [ 3.014204] rk808-rtc rk808-rtc: setting system clock to 2016-01-21T08:50:07 UTC (1453366207) [ 3.016397] input: rk805 pwrkey as /devices/platform/ff160000.i2c/i2c-1/1-0018/rk805-pwrkey/input/input0 [ 3.019896] IR NEC protocol handler initialized [ 3.022884] rockchip-thermal ff250000.tsadc: Missing tshut mode property, using default (cru) [ 3.023702] rockchip-thermal ff250000.tsadc: Missing tshut-polarity property, using default (low) [ 3.026643] dw_wdt ff1a0000.watchdog: No valid TOPs array specified [ 3.028515] device-mapper: uevent: version 1.0.3 [ 3.029551] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com [ 3.036635] sdhci: Secure Digital Host Controller Interface driver [ 3.037237] sdhci: Copyright(c) Pierre Ossman [ 3.037642] Synopsys Designware Multimedia Card Interface Driver [ 3.038821] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.039705] dwmmc_rockchip ff500000.mmc: IDMAC supports 32-bit address mode. [ 3.040416] dwmmc_rockchip ff500000.mmc: Using internal DMA controller. [ 3.041034] dwmmc_rockchip ff500000.mmc: Version ID is 270a [ 3.041657] dwmmc_rockchip ff500000.mmc: DW MMC controller at irq 36,32 bit host data width,256 deep fifo [ 3.042639] ledtrig-cpu: registered to indicate activity on CPUs [ 3.042902] vcc_sd: supplied by vcc_io [ 3.043930] hid: raw HID events driver (C) Jiri Kosina [ 3.045156] usbcore: registered new interface driver usbhid [ 3.045692] usbhid: USB HID core driver [ 3.054514] Initializing XFRM netlink socket [ 3.056046] NET: Registered protocol family 10 [ 3.058943] Segment Routing with IPv6 [ 3.062891] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 3.083562] bpfilter: Loaded bpfilter_umh pid 161 [ 3.084629] NET: Registered protocol family 17 [ 3.085585] Bluetooth: RFCOMM TTY layer initialized [ 3.086088] Bluetooth: RFCOMM socket layer initialized [ 3.086671] Bluetooth: RFCOMM ver 1.11 [ 3.087071] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 3.087630] Bluetooth: HIDP socket layer initialized [ 3.088271] Key type dns_resolver registered [ 3.089781] registered taskstats version 1 [ 3.090189] Loading compiled-in X.509 certificates [ 3.090848] Key type ._fscrypt registered [ 3.091234] Key type .fscrypt registered [ 3.091595] Key type fscrypt-provisioning registered [ 3.137021] friendlyelec-board board: Serial : 5cdb999105b0e27e [ 3.140573] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 3.141474] rk3328-dmc-freq dmc: current ATF version 0x101 [ 3.142144] mmc0: new high speed SD card at address a79d [ 3.144065] mmcblk0: mmc0:a79d SD02G 1.88 GiB [ 3.146408] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 3.147173] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 3.148943] input: gpio-keys as /devices/platform/gpio-keys/input/input1 [ 3.151681] ALSA device list: [ 3.151994] No soundcards found. [ 3.152699] dw-apb-uart ff130000.serial: forbid DMA for kernel console [ 3.153995] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.154735] GPT:1953123 != 3932159 [ 3.155049] GPT:Alternate GPT header not at the end of the disk. [ 3.155584] GPT:1953123 != 3932159 [ 3.155894] GPT: Use GNU Parted to correct GPT errors. [ 3.156492] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 [ 3.164162] Freeing unused kernel memory: 9792K [ 3.178491] Run /init as init process Loading, please wait... Starting version 245.4-4ubuntu3.2 [ 3.290711] usb 5-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 3.311581] usb 5-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00 [ 3.312347] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [ 3.312992] usb 5-1: Product: USB 10/100/1000 LAN [ 3.313419] usb 5-1: Manufacturer: Realtek [ 3.313792] usb 5-1: SerialNumber: 000000000000 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 4.154971] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null) Begin: Will now check userdata file system ... fsck from util-linux 2.34 [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p9] fsck.ext4 -a -C0 /dev/mmcblk0p9 userdata: clean, 11/6400 files, 1438/25600 blocks done. [ 4.467628] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: (null) Begin: Resizing ext4 file system on /dev/mmcblk0p9 ... Model: SD SD02G (sd/mmc) Disk /dev/mmcblk0: 100% Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 0.42% 0.62% 0.21% uboot 2 0.63% 0.83% 0.21% trust 3 0.83% 1.04% 0.21% misc 4 1.04% 1.25% 0.21% dtbo 5 1.25% 2.08% 0.83% resource 6 2.08% 4.17% 2.08% kernel 7 4.17% 6.67% 2.50% boot 8 6.67% 29.8% 23.1% ext4 rootfs 9 29.8% 100% 70.2% ext4 userdata resize2fs 1.45.5 (07-Jan-2020) Resizing the filesystem on /dev/mmcblk0p9 to 345083 (4k) blocks. The filesystem on /dev/mmcblk0p9 is now 345083 (4k) blocks long. done. [ 5.927407] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: (null) [ 6.108848] overlayfs: "xino" feature enabled using 32 upper inode bits. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 6.352911] init: Console is alive [ 6.353418] init: - watchdog - [ 11.554885] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 11.638368] raid6: neonx8 gen() 963 MB/s [ 11.706346] raid6: neonx8 xor() 1250 MB/s [ 11.774347] raid6: neonx4 gen() 2362 MB/s [ 11.842338] raid6: neonx4 xor() 1686 MB/s [ 11.910342] raid6: neonx2 gen() 2293 MB/s [ 11.978399] raid6: neonx2 xor() 1574 MB/s [ 12.046415] raid6: neonx1 gen() 1787 MB/s [ 12.114426] raid6: neonx1 xor() 998 MB/s [ 12.182362] raid6: int64x8 gen() 1001 MB/s [ 12.250433] raid6: int64x8 xor() 787 MB/s [ 12.318431] raid6: int64x4 gen() 1369 MB/s [ 12.386443] raid6: int64x4 xor() 574 MB/s [ 12.454399] raid6: int64x2 gen() 860 MB/s [ 12.522446] raid6: int64x2 xor() 488 MB/s [ 12.590543] raid6: int64x1 gen() 365 MB/s [ 12.658539] raid6: int64x1 xor() 201 MB/s [ 12.658961] raid6: using algorithm neonx4 gen() 2362 MB/s [ 12.659468] raid6: .... xor() 1686 MB/s, rmw enabled [ 12.659937] raid6: using neon recovery algorithm [ 12.671345] xor: measuring software checksum speed [ 12.680322] 8regs : 1178 MB/sec [ 12.687864] 32regs : 1394 MB/sec [ 12.697084] arm64_neon : 1121 MB/sec [ 12.697490] xor: using function: 32regs (1394 MB/sec) [ 12.888846] Btrfs loaded, crc32c=crc32c-generic [ 12.899009] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 12.905544] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 16.220983] mount_root: mounting /dev/root [ 16.253920] mount_root: loading kmods from internal overlay [ 16.480407] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 16.484776] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 17.092572] block: attempting to load /etc/config/fstab [ 17.094598] block: unable to load configuration (fstab: Entry not found) [ 17.095357] block: no usable configuration [ 17.099987] urandom-seed: Seed file not found (/etc/urandom.seed) Scanning for Btrfs filesystems [ 17.501966] procd: - early - [ 17.502531] procd: - watchdog - [ 18.094718] procd: - watchdog - [ 18.095274] procd: - ubus - [ 18.280428] procd: - init - Please press Enter to activate this console. [ 18.390717] urngd: v1.0.2 started. [ 18.522746] kmodloader: loading kernel modules from /etc/modules.d/* [ 18.564293] usbcore: registered new interface driver r8152 [ 18.650577] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 18.750050] usb 5-1: reset SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 18.786238] r8152 5-1:1.0 (unnamed net_device) (uninitialized): DT mac addr 3a:7f:91:dc:ea:3f [ 18.806850] r8152 5-1:1.0: load rtl8153b-2 v1 10/23/19 successfully [ 18.854571] r8152 5-1:1.0 eth1: v1.11.11 [ 18.911439] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 19.246500] rtl8812au: loading out-of-tree module taints kernel. [ 19.272673] usbcore: registered new interface driver 88XXau [ 19.457405] usbcore: registered new interface driver rtl8821cu [ 19.689653] usbcore: registered new interface driver rtl88x2bu [ 19.789119] usbcore: registered new interface driver mt76x2u [ 19.797519] NET: Registered protocol family 8 [ 19.797934] NET: Registered protocol family 20 [ 20.099163] Key type encrypted registered [ 20.124867] NET: Registered protocol family 15 [ 20.138612] tun: Universal TUN/TAP device driver, 1.6 [ 20.190500] l2tp_core: L2TP core driver, V2.0 [ 20.196108] l2tp_netlink: L2TP netlink interface [ 20.220207] gre: GRE over IPv4 demultiplexor driver [ 20.228520] ip_gre: GRE over IPv4 tunneling driver [ 20.397554] Mirror/redirect action on [ 20.441717] u32 classifier [ 20.441988] input device check on [ 20.442323] Actions configured [ 20.578885] usbcore: registered new interface driver cdc_ncm [ 20.585277] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 20.799271] PPP MPPE Compression module registered [ 20.801354] NET: Registered protocol family 24 [ 20.803287] PPTP driver version 0.8.5 [ 20.872864] xt_time: kernel timezone is -0000 [ 20.898945] usbcore: registered new interface driver brcmfmac [ 20.914874] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 20.918249] usbcore: registered new interface driver cdc_mbim [ 20.928721] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 20.940196] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 20.940917] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 20.943726] Bridge firewalling registered [ 20.947903] kmodloader: done loading kernel modules from /etc/modules.d/* Please press Enter to activate this console. [ 49.253350] br-lan: port 1(eth1) entered blocking state [ 49.253894] br-lan: port 1(eth1) entered disabled state [ 49.255065] device eth1 entered promiscuous mode [ 49.257293] br-lan: port 1(eth1) entered blocking state [ 49.257806] br-lan: port 1(eth1) entered forwarding state [ 49.275129] rk_gmac-dwmac ff540000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8211E Gigabit Ethernet] (irq=POLL) [ 49.286571] rk_gmac-dwmac ff540000.ethernet eth0: No Safety Features support found [ 49.287297] rk_gmac-dwmac ff540000.ethernet eth0: PTP not supported by HW [ 49.289003] rk_gmac-dwmac ff540000.ethernet eth0: configuring for phy/rgmii link mode [ 50.238804] br-lan: port 1(eth1) entered disabled state [ 53.375743] rk_gmac-dwmac ff540000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 53.376685] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.113706] overlayfs: filesystem on '/opt/check-overlayfs-support261110629/upper' not supported as upperdir [ 54.252877] overlayfs: filesystem on '/opt/check-overlayfs-support011156864/upper' not supported as upperdir [ 58.711026] process 'opt/tmp/qemu-check739621160/check' started with executable stack
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.4.72 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14798-e91344776b)) #0 SMP PREEMPT Thu Oct 29 13:35:03 2020 [ 0.000000] Machine model: FriendlyElec NanoPi R2S [ 0.000000] earlycon: uart8250 at MMIO32 0x00000000ff130000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] cma: Reserved 8 MiB at 0x000000003f800000 [ 0.000000] On node 0 totalpages: 261632 [ 0.000000] DMA32 zone: 4088 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 261632 pages, LIFO batch:63 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 21 pages/cpu s45912 r8192 d31912 u86016 [ 0.000000] pcpu-alloc: s45912 r8192 d31912 u86016 alloc=21*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257544 [ 0.000000] Kernel command line: console=ttyS2,1500000 earlycon=uart8250,mmio32,0xff130000 root=PARTUUID=5452574f-02 rw rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1004768K/1046528K available (7614K kernel code, 572K rwdata, 2372K rodata, 1664K init, 715K bss, 33568K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x29c/0x39c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001333] Console: colour dummy device 80x25 [ 0.001860] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.002791] pid_max: default: 32768 minimum: 301 [ 0.003449] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.004129] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.006953] ASID allocator initialised with 32768 entries [ 0.007569] rcu: Hierarchical SRCU implementation. [ 0.009136] smp: Bringing up secondary CPUs ... [ 0.010321] Detected VIPT I-cache on CPU1 [ 0.010408] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.011170] Detected VIPT I-cache on CPU2 [ 0.011229] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.011934] Detected VIPT I-cache on CPU3 [ 0.011988] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.012096] smp: Brought up 1 node, 4 CPUs [ 0.015396] SMP: Total of 4 processors activated. [ 0.015830] CPU features: detected: 32-bit EL0 Support [ 0.016298] CPU features: detected: CRC32 instructions [ 0.025157] CPU: All CPU(s) started at EL2 [ 0.025564] alternatives: patching kernel code [ 0.038122] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.039072] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.040342] pinctrl core: initialized pinctrl subsystem [ 0.042001] NET: Registered protocol family 16 [ 0.044763] DMA: preallocated 256 KiB pool for atomic allocations [ 0.046396] cpuidle: using governor menu [ 0.047165] Serial: AMBA PL011 UART driver [ 0.074017] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.074638] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.075245] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.075872] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.079816] sdmmc-regulator GPIO handle specifies active low - ignored [ 0.081808] iommu: Default domain type: Translated [ 0.083450] SCSI subsystem initialized [ 0.084071] usbcore: registered new interface driver usbfs [ 0.084621] usbcore: registered new interface driver hub [ 0.085214] usbcore: registered new device driver usb [ 0.086005] pps_core: LinuxPPS API ver. 1 registered [ 0.086456] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.087340] PTP clock support registered [ 0.088304] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.090329] clocksource: Switched to clocksource arch_sys_counter [ 0.091193] VFS: Disk quotas dquot_6.6.0 [ 0.091635] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.097636] thermal_sys: Registered thermal governor 'step_wise' [ 0.097644] thermal_sys: Registered thermal governor 'power_allocator' [ 0.098869] NET: Registered protocol family 2 [ 0.100757] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.101549] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.102414] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.103256] TCP: Hash tables configured (established 8192 bind 8192) [ 0.104033] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.104675] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.105767] NET: Registered protocol family 1 [ 0.106205] PCI: CLS 0 bytes, default 64 [ 0.108163] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.118679] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.119221] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.122198] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.123258] io scheduler mq-deadline registered [ 0.129915] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330 [ 0.130614] dma-pl330 ff1f0000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 0.133896] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.138644] printk: console [ttyS2] disabled [ 0.139166] ff130000.serial: ttyS2 at MMIO 0xff130000 (irq = 12, base_baud = 1500000) is a 16550A [ 0.140052] printk: console [ttyS2] enabled [ 0.140805] printk: bootconsole [uart8250] disabled [ 0.150815] loop: module loaded [ 0.151118] mtip32xx Version 1.3.1 [ 0.151580] Loading iSCSI transport class v2.0-870. [ 0.154712] libphy: Fixed MDIO Bus: probed [ 0.156240] clk: failed to reparent clk_mac2io to gmac_clk: -22 [ 0.156785] clk: failed to reparent clk_mac2io_ext to gmac_clk: -22 [ 0.157396] rk_gmac-dwmac ff540000.ethernet: IRQ eth_wake_irq not found [ 0.157984] rk_gmac-dwmac ff540000.ethernet: IRQ eth_lpi not found [ 0.158734] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock [ 0.159302] rk_gmac-dwmac ff540000.ethernet: phy regulator is not available yet, deferred probing [ 0.161524] dwc3 ff600000.dwc3: Failed to get clk 'ref': -2 [ 0.162574] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.163155] ehci-pci: EHCI PCI platform driver [ 0.163622] ehci-platform: EHCI generic platform driver [ 0.166460] ehci-platform ff5c0000.usb: EHCI Host Controller [ 0.166991] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 1 [ 0.167823] ehci-platform ff5c0000.usb: irq 28, io mem 0xff5c0000 [ 0.182365] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00 [ 0.183583] hub 1-0:1.0: USB hub found [ 0.183957] hub 1-0:1.0: 1 port detected [ 0.184824] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.185413] ohci-platform: OHCI generic platform driver [ 0.186231] ohci-platform ff5d0000.usb: Generic Platform OHCI controller [ 0.186905] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 2 [ 0.187743] ohci-platform ff5d0000.usb: irq 29, io mem 0xff5d0000 [ 0.251002] hub 2-0:1.0: USB hub found [ 0.251377] hub 2-0:1.0: 1 port detected [ 0.252760] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 0.253274] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3 [ 0.254153] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010 [ 0.255112] xhci-hcd xhci-hcd.0.auto: irq 163, io mem 0xff600000 [ 0.256554] hub 3-0:1.0: USB hub found [ 0.256925] hub 3-0:1.0: 1 port detected [ 0.257681] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 0.258187] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4 [ 0.258925] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 0.259577] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 0.260815] hub 4-0:1.0: USB hub found [ 0.261185] hub 4-0:1.0: 1 port detected [ 0.262132] usbcore: registered new interface driver usb-storage [ 0.262890] i2c /dev entries driver [ 0.265273] rk808 1-0018: chip id: 0x8050 [ 0.271440] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 0.272025] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 0.272654] DCDC_REG1: supplied by vdd_5v [ 0.275652] DCDC_REG2: supplied by vdd_5v [ 0.277551] DCDC_REG3: supplied by vdd_5v [ 0.278161] DCDC_REG4: supplied by vdd_5v [ 0.279830] LDO_REG1: supplied by vcc_io_33 [ 0.283177] LDO_REG2: supplied by vcc_io_33 [ 0.286601] LDO_REG3: supplied by vdd_5v [ 0.298835] rk808-rtc rk808-rtc: registered as rtc0 [ 0.299489] i2c i2c-1: of_i2c: modalias failure on /i2c@ff160000/usb [ 0.300057] i2c i2c-1: Failed to create I2C device for /i2c@ff160000/usb [ 0.305948] energy_model: pd0: hertz/watts ratio non-monotonically decreasing: em_cap_state 1 >= em_cap_state0 [ 0.308670] sdhci: Secure Digital Host Controller Interface driver [ 0.309224] sdhci: Copyright(c) Pierre Ossman [ 0.309609] Synopsys Designware Multimedia Card Interface Driver [ 0.310873] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode. [ 0.311546] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller. [ 0.312146] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a [ 0.312705] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo [ 0.313614] vcc_sd: supplied by vcc_io_33 [ 0.330410] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 0.344009] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.345720] ledtrig-cpu: registered to indicate activity on CPUs [ 0.346495] hidraw: raw HID events driver (C) Jiri Kosina [ 0.347132] usbcore: registered new interface driver usbhid [ 0.347649] usbhid: USB HID core driver [ 0.349373] NET: Registered protocol family 10 [ 0.351004] Segment Routing with IPv6 [ 0.351414] NET: Registered protocol family 17 [ 0.351891] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.353043] 8021q: 802.1Q VLAN Support v1.8 [ 0.370928] clk: failed to reparent clk_mac2io to gmac_clk: -22 [ 0.371474] clk: failed to reparent clk_mac2io_ext to gmac_clk: -22 [ 0.372064] rk_gmac-dwmac ff540000.ethernet: IRQ eth_wake_irq not found [ 0.372646] rk_gmac-dwmac ff540000.ethernet: IRQ eth_lpi not found [ 0.373427] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock [ 0.374140] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input). [ 0.374809] rk_gmac-dwmac ff540000.ethernet: TX delay(0x24). [ 0.375310] rk_gmac-dwmac ff540000.ethernet: RX delay(0x18). [ 0.375818] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no). [ 0.376408] rk_gmac-dwmac ff540000.ethernet: cannot get clock clk_mac_speed [ 0.377015] rk_gmac-dwmac ff540000.ethernet: clock input from PHY [ 0.382593] rk_gmac-dwmac ff540000.ethernet: init for RGMII [ 0.383348] rk_gmac-dwmac ff540000.ethernet: User ID: 0x10, Synopsys ID: 0x35 [ 0.383988] rk_gmac-dwmac ff540000.ethernet: DWMAC1000 [ 0.384454] rk_gmac-dwmac ff540000.ethernet: DMA HW capability register supported [ 0.385117] rk_gmac-dwmac ff540000.ethernet: RX Checksum Offload Engine supported [ 0.385773] rk_gmac-dwmac ff540000.ethernet: COE Type 2 [ 0.386234] rk_gmac-dwmac ff540000.ethernet: TX Checksum insertion supported [ 0.386898] rk_gmac-dwmac ff540000.ethernet: Wake-Up On Lan supported [ 0.387486] rk_gmac-dwmac ff540000.ethernet: Normal descriptors [ 0.388021] rk_gmac-dwmac ff540000.ethernet: Ring mode enabled [ 0.388535] rk_gmac-dwmac ff540000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.389407] libphy: stmmac: probed [ 0.433505] mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0) [ 0.435316] random: fast init done [ 0.460677] rk808-rtc rk808-rtc: setting system clock to 2020-11-02T05:33:07 UTC (1604295187) [ 0.463284] Waiting for root device PARTUUID=5452574f-02... [ 0.594451] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 1.596436] dwmmc_rockchip ff500000.dwmmc: Successfully tuned phase to 89 [ 1.597089] mmc0: new ultra high speed SDR104 SDHC card at address aaaa [ 1.599147] mmcblk0: mmc0:aaaa SC32G 29.7 GiB [ 1.602423] mmcblk0: p1 p2 p3 [ 1.624742] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended [ 1.643935] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null) [ 1.644697] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 1.646571] Freeing unused kernel memory: 1664K [ 1.662363] Run /sbin/init as init process [ 1.709971] init: Console is alive [ 1.765318] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 1.781371] uhci_hcd: USB Universal Host Controller Interface driver [ 1.783125] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 1.792062] init: - preinit - [ 1.930140] random: jshn: uninitialized urandom read (4 bytes read) [ 1.952282] random: jshn: uninitialized urandom read (4 bytes read) [ 1.971124] random: hexdump: uninitialized urandom read (5 bytes read) [ 6.127485] mount_root: mounting /dev/root [ 6.130555] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 6.131323] mount_root: loading kmods from internal overlay [ 6.139289] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 6.140703] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 6.194522] block: attempting to load /etc/config/fstab [ 7.137407] EXT4-fs (mmcblk0p3): recovery complete [ 7.138838] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: [ 7.148734] mount_root: switched to extroot [ 7.202658] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null) [ 7.212003] urandom-seed: Seeding with /etc/urandom.seed [ 7.234757] procd: - early - [ 7.783519] procd: - ubus - [ 7.796766] urandom_read: 5 callbacks suppressed [ 7.796776] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.837267] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.838767] procd: - init - [ 7.957637] urngd: v1.0.2 started. [ 7.976712] kmodloader: loading kernel modules from /etc/modules.d/* [ 7.981838] random: crng init done [ 8.008055] usbcore: registered new interface driver r8152 [ 8.016435] xt_time: kernel timezone is -0000 [ 8.029377] PPP generic driver version 2.4.2 [ 8.030813] NET: Registered protocol family 24 [ 8.039871] kmodloader: done loading kernel modules from /etc/modules.d/* [ 8.179778] usb 4-1: reset SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 8.215908] r8152 4-1:1.0 (unnamed net_device) (uninitialized): Invalid ether addr 00:00:00:00:00:00 [ 8.216745] r8152 4-1:1.0 (unnamed net_device) (uninitialized): Random ether addr ca:e2:a0:45:5c:aa [ 8.252004] r8152 4-1:1.0 eth1: v1.10.11 [ 10.673084] br-lan: port 1(eth1) entered blocking state [ 10.673100] br-lan: port 1(eth1) entered disabled state [ 10.673501] device eth1 entered promiscuous mode [ 10.675310] br-lan: port 1(eth1) entered blocking state [ 10.675331] br-lan: port 1(eth1) entered forwarding state [ 10.739227] rk_gmac-dwmac ff540000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8211E Gigabit Ethernet] [ 10.750424] rk_gmac-dwmac ff540000.ethernet eth0: No Safety Features support found [ 10.750453] rk_gmac-dwmac ff540000.ethernet eth0: PTP not supported by HW [ 10.751091] rk_gmac-dwmac ff540000.ethernet eth0: configuring for phy/rgmii link mode [ 11.682902] br-lan: port 1(eth1) entered disabled state [ 11.717046] r8152 4-1:1.0 eth1: Promiscuous mode enabled [ 11.717319] r8152 4-1:1.0 eth1: carrier on [ 11.717837] br-lan: port 1(eth1) entered blocking state [ 11.717852] br-lan: port 1(eth1) entered forwarding state [ 12.706413] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 13.826955] rk_gmac-dwmac ff540000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 13.827046] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 18.985803] pppoe-wan: renamed from ppp0
Space for additional notes, links to forum threads or other resources.
cat /etc/rc.local
echo performance > /sys/devices/system/cpu/cpufreq/policy0/scaling_governor