D-Link DAP-2660 A2

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The D-Link DAP-2660 is a dualband Access Point with a single ethernet port and POE from the D-Link DAP Series of Business Access Points, manufactured by Alpha Networks.

Any text with a light background (like this one) provides instructions for creating the Details Page. When you have filled in correct/useful information (instead of any template that's there) remove the instructions, as well as the <WRAP> that encloses it.

Getting started with a new Device Page

This is an empty template that suggests the information that should be present on a well-constructed Device Page. This means, that you have to fill it with life and information.
There are several “fixme” tags with text on a light background (like this text) throughout this template. As you fill in the page, remove those tags so that people can judge its completeness.
When there are no more “fixme” tags left, delete this one too, along with the <WRAP> that encloses it.

Keep the articles modular

Please include only model specific information, omit bla,bla and put everything generic into separate articles
If you have no time to write certain stuff, link to docs
base-system should lead the way, do not explain this again
DO NOT provide a complete howto here! Instead groom the general documentation.

Supported Versions

Hardware Highlights

Installation

→ Install OpenWrt (Method 1 via OEM Firmware)

Flash Layout

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

OEM easy installation

OpenWrt can be installed through the D-Link firmware upgrade process with the WebUI. Use an image xxxxx_factory.bin

OEM installation using the TFTP method

→ generic.flashing.tftp

Specific values needed for tftp

Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address	FILL-IN
Bootloader MAC address (special)	FILL-IN
Firmware tftp image	Latest OpenWrt release (`NOTE:` Name must contain “tftp”)
TFTP transfer window	FILL-IN seconds
TFTP window start	approximately FILL-IN seconds after power on
TFTP client required IP address	FILL-IN

Upgrading OpenWrt

→ generic.sysupgrade

Debricking

→ see Unbricking section in D-Link DAP Series of Business Access Points

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, etc.

Specific Configuration

Please fill in real values for this device, then remove the EXAMPLEs

Network interfaces

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Switch Ports (for VLANs)

This access point does not have an internal switch.

You can configure 802.1q VLANs on eth0 if you like.

Buttons

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The D-Link DAP-2660 has the following buttons:

BUTTON	Event
Reset	reset

Press Reset button shorter than 1 second: perform a reboot.

Press Reset button more than 5 seconds: perform a factory reset.

Hardware

Info

Photos

Front:

Back:

Backside label:
Insert photo of backside label

Opening the case

Note: This will void your warranty!

To open the device

Remove the four screws on the backside
The cover has one or two clips on each edge. Start at the edge near the LED.
Press the lower part with the thumb and try to loosen the clip.
When some clips break, no problem, the screws are sufficient to hold the cover well. (looks like the clips are more like a warranty void indicator)

PCB component side:

PCB back side:

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters for D-Link DAP-2660 A2	115200, 8N1

ATTENTION: the serial console uses 2,5V levels - don't try to use a standard 3,3V level serial converter!

JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE

OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING

Notes

Space for additional notes, links to forum threads or other resources.

Table of Contents