This router is standardly powered via USB at 5V. The voltage regulator inside is unknown, but its input voltage should be at least between 3.7V - 5.5V, but not over 5.5V. The device will get damaged at too high voltages*. Maximum current draw at 5V is 185mA (OpenWrt boot), average current draw with WiFi at 18dBm is 100mA, without WiFi 80mA. Hence the average router power consumption is 0.5W, which is incredibly low.
Power consumption will be higher if a USB device is attached to its USB port!
*Hint: If the router seems to be damaged because of a too high voltage, connect 3.3V _after_ the voltage regulator. This replaces the function of the damaged regulator, and the router works again.
Be sure to power 5 volts into the micro-usb port at the same time if you want to have the usb port on the device work.
More information and a rough diagram here http://img513.imageshack.us/img513/4295/saai.jpg
The serial console connector does not utilise the regular TP-Link pinouts. Two pads labelled TP_OUT andTP_IN are the TX and RX signals. 115200 8n1
Note that the pads can very easily be lifted. There is slightly more mechanical strength if you can solder to the surface-mount components to which the pads are connected–but this also takes care–your device could easily be destroyed. Make sure that your connection is secured so that tension cannot be applied to the solder points when you connect to an external device.
Upload the latest snapshot via the web interface (default: 192.168.1.1 / admin / admin).
Note that the factory default web interface won't accept a file with a long name. Rename it to openwrt.bin and you won't get a “23002 Error”.
For systems without a web interface, you can flash a sysupgrade file with mtd:
To flash from the Chinese web interface, at the present time you would select the last menu item on the left, and then the third submenu item. This initiates a popup with two buttons–the upper right one allows you to browse to find the file you want to flash on your PC, the lower left one initiates the flash.
When you roll over an item on the Chinese web interface, the rollover text will indicate which item you are selecting.
When the configuration no longer allows you to log in via any network connection (e.g. lost password), the OpenWrt failsafe mode can be entered via the single “Reset” button on the device. However, in contrast to the generic failsafe instructions, for the TL-WR703N you have to wait for ca. 10 (10-12) seconds before pushing the “Reset” button after powering on the device. If the button is pushed immediately after powering on, the single blue LED will start blinking, supposedly indicating some failsafe firmware recovery mody of the embedded bootloader (not yet discovered how to use it). In this mode, the OpenWrt failsafe is not being started. Instead, wait for slightly longer than 10 seconds and - as soon as the LED starts blinking for the first time after powering on the device, push the “Reset” button for ca. 1-2 seconds. Immediately afterwards, the LED will blink rapidly (multiple Hz) and OpenWrt will be in failsafe mode.
- The above didn't work on a Ver 1.6 box running OpenWRT r33312. To get into failsafe mode, power up the device and wait until the LED starts flashing (about 2Hz). Once it starts flashing (within about 4 seconds) then quickly press the button. The LED will then flash much faster and the device will be in failsafe mode.
Back to original image
Setup serial console 115200 8n1
Enter “tpl” as soon as U-Boot announces “Autobooting in 1 seconds”
USB port and monitoring Serial Console via USB-Serial
The USB port on the WR703n is not compatible with USB1 devices (aka full speed) and only works properly with USB2 (aka high speed) devices. You can however plug a USB-Serial adapter as long as you plug that through a <$10 USB2. While you're at it, use another USB port to plug in a USB key and write data there (like serial console logs) so as not to wear out the built in flash.
This project implements a webradio with cheep usb soundcard and a speaker of an old mobile phone within the casing of the router. There are two analogue controllers for selecting the stream and the volume. Therefor an attiny85 is connected to the uart.
The Device uses a DDR1 16Mbit x 16bit (16Mibit*16=256 mebibit. 256 mebibit/8=32MiByte) 400MHz chip Zentel A3S56D40FTP. Replace it with any 32Mbit x 16bit chip. 333MHz instead of 400MHz also works fine. It's quite hard to find these chips. One of the ways to get them is to have a look at DDR SO-DIMM (because SO-DIMM modules are shipped with x16 chips). Since there are no 64Mbit x 16bit DDR1 Chips available → no 128 MB mod!
The most easy approach is to seek for a 4-chip DDR 256 MB module. These all have x16 chips too. Chips only on one side (not to be confused with double-sided 256 MB modules with 4 chips on each side) and only 4 of them - that's the best chance to get some. They represent a small percent among usual 8-chip modules but this is equalized with the amount and “cheap as dirt” price of such DDR 256 MB modules.
total used free shared buffers
Mem: 61864 48044 13820 0 30316
The MiniPwner's key features include:
Integrated Wired and Wireless connections
Once plugged into a target network, the Mini-Pwner can establish an SSH tunnel through the target network, or can be accessed by wifi. In addition, the MiniPwner can be configured as a wifi sniffer and logger - wardriving in your pocket.
Low power consumption, can be run off battery.
With the 1700 mAh battery included in the kit, the Mini-Pwner will run for over five hours of active wired and wireless activity. No need to find a power outlet during the pen test.
Multiple Pen Testing Tools included
tcpdump, nmap, kismet, all come pre-installed
Flexible and Expandable
The MiniPwner runs on the open source OpenWrt operating system. You can easily add or change the installed packages.
The MiniPwner can be easily carried in a pocket, hidden behind a telephone, or hang from a jack by a short ethernet cable.
There are many other creative ways to use the MiniPwner. Here is a list of some of the software that comes installed:
Nmap network scanner
Netcat Hacker’s swiss army knife
aircrack Wireless network analysis
kismet Wireless network analysis
perl Perl Scripting Language
openvpn VPN Client and Server
dsniff suite of sniffing and spoofing tools, including arpspoof
nbtscan NetBIOS Network Scanner
snort Sniffer, Packet Logger, Intrusion Detection System
Kean Electronics in conjunction with the Sydney Hackerspace has developed WR703N Expander board as Open Hardware, all schematics are available online on their website - http://www.kean.com.au/oshw/WR703N/
The upstream USB connection is intended to come via a 4 pin header plugged into the WR703N PCB below (existing USB connector removed).
You can also populate a mini-B connector for connection to any upstream USB host via a
You can populate up to 3 USB A female connectors, or use 0.1“ headers/connectors to mount USB connectors
USB1 and USB2 are intended to be standard right angle connectors, but will also take vertical style.
USB2 is recessed - partly to make the PCB able to be mounted very low on top of the WR703N PCB, but it also makes it suitable for very small USB drives (Sandisk Cruzer Fit).
USB3 can be a right angle or more usually a vertical connector. Or left off completely.
If a right angle connector is used for USB3, you can't easily use PORTB (and you should probably put some insulating tape over the PORTB pads).
The PORTA and PORTB headers are similar to the common SparkFun FTDI connector, although they include RTS instead of DTR.
The GPIO connector is intended to be a standard 2×5 box header.
See the schematic for pin outs of the GPIO and serial ports. Due to space restrictions, the extra 8 GPIO's from PORTB are not routed out.
zh/toh/tp-link/tl-wr703n.txt · Last modified: 2019/12/24 00:33 by kkjoy