Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
zh-tw:toh:buffalo:wzr-hp-ag300h [2018/02/20 18:51] – ↷ Links adapted because of a move operation bobafetthotmailzh-tw:toh:buffalo:wzr-hp-ag300h [2018/03/03 20:34] – ↷ Links adapted because of a move operation
Line 89: Line 89:
   * 上傳[[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-wzr-hp-ag300h-squashfs-factory.bin|OpenWRT韌體]]   * 上傳[[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-wzr-hp-ag300h-squashfs-factory.bin|OpenWRT韌體]]
   * 讓電腦自動取得OpenWRT新的IP位置   * 讓電腦自動取得OpenWRT新的IP位置
-  * 請參考[[docs:guide-quick-start:first_steps]] 第一次安裝+  * 請參考[[docs:guide-quick-start:checks_and_troubleshooting]] 第一次安裝
 FIXME FIXME
  
  
 ==== 升級OpenWrt ==== ==== 升級OpenWrt ====
-->  [[docs:user-guide:generic.sysupgrade]]+->  [[docs:guide-user:installation:generic.sysupgrade]]
  
 ==== 基本設定 ==== ==== 基本設定 ====
-[[docs:guide-quick-start:first_steps|Basic configuration]]+[[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]]
 設定您的Internet連縣,配定無線網路,USB 等設定 設定您的Internet連縣,配定無線網路,USB 等設定
  
 ==== 救援模式 ==== ==== 救援模式 ====
--> [[docs:user-guide:failsafe_and_factory_reset]]+-> [[docs:user-guide:troubleshooting:failsafe_and_factory_reset]]
  
 If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
Line 123: Line 123:
 ==== 解磚 ==== ==== 解磚 ====
   * 你的設備不太可能會變磚,請先試試用TFTP的方法,如果還是不行、用較為進階的方式   * 你的設備不太可能會變磚,請先試試用TFTP的方法,如果還是不行、用較為進階的方式
--> [[docs:user-guide:generic.debrick]]+-> [[docs:user-guide:troubleshooting:generic.debrick]]
  
 ====網路孔分配示意==== ====網路孔分配示意====
Line 134: Line 134:
  
 ==== 按鍵 ==== ==== 按鍵 ====
--> [[docs:user-guide:hardware:hardware.button]] 關於如何使用和設定硬體按鍵。+-> [[docs:guide-user:hardware:hardware.button]] 關於如何使用和設定硬體按鍵。
  
 ^ 按鍵 ^ 事件 ^ ^ 按鍵 ^ 事件 ^
  • Last modified: 2018/03/31 23:23
  • by bobafetthotmail