Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:zyxel:xgs1250-12 [2022/02/25 12:36] – [ZyXEL XGS1250-12] borromini | toh:zyxel:xgs1250-12 [2022/11/28 15:48] – [Tags] added torev | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ZyXEL XGS1250-12 ====== | ====== ZyXEL XGS1250-12 ====== | ||
| - | < | + | |
| - | Support for the RTL930x subtarget is still very fresh. | + | < |
| + | \\ Support for the RTL930x subtarget is still very fresh. | ||
| </ | </ | ||
| Line 10: | Line 11: | ||
| {{media: | {{media: | ||
| + | |||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| Line 93: | Line 95: | ||
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| - | <WRAP BOX> | + | * Connect serial as per the [[toh: |
| - | FIXME //The instructions below are for Broadcom devices | + | * Navigate to ' |
| - | **//Remove | + | * Upload the OpenWrt initramfs image, and wait till the switch reboots into OpenWrt. |
| + | | ||
| + | * Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it: < | ||
| + | | ||
| + | ==== Booting OpenWrt from RAM ==== | ||
| - | This section deals with | + | -> [[docs: |
| - | * How you install OpenWrt from a device freshly opened | + | |
| - | * The steps required such as reset to factory defaults if the device has already been configured | + | |
| - | **Note:** Reset router | + | The XGS1250-12 can boot from the network, but for that you'd need to manipulate the boot command. ZyXEL password protected the U-boot environment. However, if you change the bootcmd |
| - | * Browse | + | |
| - | * Upload .bin file to router | + | |
| - | * Wait for it to reboot | + | |
| - | * Telnet to 192.168.1.1 and set a root password, or browse to ''< | + | |
| - | </ | + | |
| - | ==== OEM installation using the TFTP method ==== | ||
| - | -> [[docs: | ||
| - | === Specific values needed for tftp === | + | === Specific values needed for TFTP === |
| - | <WRAP BOX> | + | ^ Bootloader TFTP server IPv4 address |
| + | ^ Firmware TFTP image | [[: | ||
| - | FIXME Enter values for " | + | === Instructions === |
| - | ^ Bootloader tftp server IPv4 address | + | |
| - | ^ Bootloader MAC address (special) | + | |
| - | ^ Firmware tftp image | [[:downloads|Latest OpenWrt release]] (**'' | + | |
| - | ^ TFTP transfer window | + | |
| - | ^ TFTP window start | approximately FILL-IN seconds after power on | | + | * Reboot |
| - | ^ TFTP client required IP address | + | * Load the ramdisk in the U-boot shell: < |
| - | + | ||
| - | </WRAP> | + | |
| ===== Upgrading OpenWrt ===== | ===== Upgrading OpenWrt ===== | ||
| Line 726: | Line 722: | ||
| ===== Notes ===== | ===== Notes ===== | ||
| * SFP+ cage does not work yet on OpenWrt. | * SFP+ cage does not work yet on OpenWrt. | ||
| - | * 10GbE RJ-45 interfaces are said to work, but I have not been able to get them going on OpenWrt. Worked fine on OEM firmware with short CAT5E cables and X550-AT2 at the other end. | ||
| * The network needs to be initialised by the bootloader through the '' | * The network needs to be initialised by the bootloader through the '' | ||
| ===== Tags ===== | ===== Tags ===== | ||
| [[meta: | [[meta: | ||
| - | {{tag> | + | {{tag> |