Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:zyxel:xgs1250-12 [2022/02/24 17:07] – [Notes] Add note about 'rtk network on' borromini | toh:zyxel:xgs1250-12 [2022/11/28 15:48] – [Tags] added torev | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ZyXEL XGS1250-12 ====== | ====== ZyXEL XGS1250-12 ====== | ||
| + | |||
| + | <WRAP center round important 50%> | ||
| + | \\ Support for the RTL930x subtarget is still very fresh. SFP+ does not work yet. | ||
| + | </ | ||
| The ZyXEL XGS1250-12 is a web managed 11 + 1-port Multi-Gigabit L3 switch. Connectivity: | The ZyXEL XGS1250-12 is a web managed 11 + 1-port Multi-Gigabit L3 switch. Connectivity: | ||
| Line 7: | Line 11: | ||
| {{media: | {{media: | ||
| + | |||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| Line 74: | Line 79: | ||
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | <WRAP BOX> | + | The XGS1250-12 has a 16 MiB Macronix MX25L12833F NOR flash chip. The realtek target uses a dynamic kernel/ |
| - | FIXME // | + | |
| - | Please check out the article | + | ^ |
| - | </WRAP> | + | ^ Layer0 |
| + | ^ Layer1 | ||
| + | ^ Layer2 | ||
| + | ^ <color magenta> | ||
| + | ^ filesystem | ||
| + | ^ Layer3 | ||
| + | ^ Size in KiB | 896 KiB | ||
| + | ^ Name | ||
| + | ^ <color magenta> | ||
| + | ^ filesystem | ||
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| - | <WRAP BOX> | + | * Connect serial as per the [[toh: |
| - | FIXME //The instructions below are for Broadcom devices | + | * Navigate to ' |
| - | **//Remove | + | * Upload the OpenWrt initramfs image, and wait till the switch reboots into OpenWrt. |
| + | | ||
| + | * Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it: < | ||
| + | | ||
| + | ==== Booting OpenWrt from RAM ==== | ||
| - | This section deals with | + | -> [[docs: |
| - | * How you install OpenWrt from a device freshly opened | + | |
| - | * The steps required such as reset to factory defaults if the device has already been configured | + | |
| - | **Note:** Reset router | + | The XGS1250-12 can boot from the network, but for that you'd need to manipulate the boot command. ZyXEL password protected the U-boot environment. However, if you change the bootcmd |
| - | * Browse | + | |
| - | * Upload .bin file to router | + | |
| - | * Wait for it to reboot | + | |
| - | * Telnet to 192.168.1.1 and set a root password, or browse to ''< | + | |
| - | </ | + | |
| - | ==== OEM installation using the TFTP method ==== | ||
| - | -> [[docs: | ||
| - | === Specific values needed for tftp === | + | === Specific values needed for TFTP === |
| - | <WRAP BOX> | + | ^ Bootloader TFTP server IPv4 address |
| + | ^ Firmware TFTP image | [[: | ||
| - | FIXME Enter values for " | + | === Instructions === |
| - | ^ Bootloader tftp server IPv4 address | + | |
| - | ^ Bootloader MAC address (special) | + | |
| - | ^ Firmware tftp image | [[:downloads|Latest OpenWrt release]] (**'' | + | |
| - | ^ TFTP transfer window | + | |
| - | ^ TFTP window start | approximately FILL-IN seconds after power on | | + | * Reboot |
| - | ^ TFTP client required IP address | + | * Load the ramdisk in the U-boot shell: < |
| - | + | ||
| - | </WRAP> | + | |
| ===== Upgrading OpenWrt ===== | ===== Upgrading OpenWrt ===== | ||
| Line 176: | Line 183: | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | FIXME Please fill in real values for this device, then remove the EXAMPLEs | ||
| ==== Network interfaces ==== | ==== Network interfaces ==== | ||
| The default network configuration is: | The default network configuration is: | ||
| ^ Interface Name ^ Description | ^ Interface Name ^ Description | ||
| - | | br-lan | + | | br-lan |
| - | | vlan0 (eth0.0) | + | |
| - | | vlan1 (eth0.1) | + | |
| - | | wl0 | EXAMPLE WiFi | EXAMPLE Disabled | + | |
| </ | </ | ||
| Line 274: | Line 277: | ||
| Layout is exactly the same as for the ZyXEL GS1900-10HP (casing color being black): | Layout is exactly the same as for the ZyXEL GS1900-10HP (casing color being black): | ||
| - | {{: | + | {{: |
| ^ Serial connection parameters for ZyXEL XGS1250-12 | 115200, 8N1 | | ^ Serial connection parameters for ZyXEL XGS1250-12 | 115200, 8N1 | | ||
| Line 719: | Line 722: | ||
| ===== Notes ===== | ===== Notes ===== | ||
| * SFP+ cage does not work yet on OpenWrt. | * SFP+ cage does not work yet on OpenWrt. | ||
| - | * 10GbE RJ-45 interfaces are said to work, but I have not been able to get them going on OpenWrt. Worked fine on OEM firmware with short CAT5E cables and X550-AT2 at the other end. | ||
| * The network needs to be initialised by the bootloader through the '' | * The network needs to be initialised by the bootloader through the '' | ||
| ===== Tags ===== | ===== Tags ===== | ||
| [[meta: | [[meta: | ||
| - | {{tag> | + | {{tag> |