Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:zyxel:xgs1250-12 [2022/02/24 14:28] – [Notes] Added SFP+ and 10GbE RJ-45 remarks borromini | toh:zyxel:xgs1250-12 [2022/11/28 15:48] – [Tags] added torev | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ZyXEL XGS1250-12 ====== | ====== ZyXEL XGS1250-12 ====== | ||
| - | The ZyXEL XGS1250-12 is a web managed 11 + 1-port Multi-Gigabit L3 switch. | + | <WRAP center round important 50%> |
| + | \\ Support for the RTL930x subtarget is still very fresh. SFP+ does not work yet. | ||
| + | </ | ||
| + | |||
| + | The ZyXEL XGS1250-12 is a web managed 11 + 1-port Multi-Gigabit L3 switch. | ||
| + | * **8** Gigabit ports | ||
| + | * **3** 1000/2500/5000/ | ||
| + | * **1** SFP+ 10GBit uplink cage | ||
| {{media: | {{media: | ||
| Line 72: | Line 79: | ||
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | <WRAP BOX> | + | The XGS1250-12 has a 16 MiB Macronix MX25L12833F NOR flash chip. The realtek target uses a dynamic kernel/ |
| - | FIXME // | + | |
| - | Please check out the article | + | ^ |
| - | </WRAP> | + | ^ Layer0 |
| + | ^ Layer1 | ||
| + | ^ Layer2 | ||
| + | ^ <color magenta> | ||
| + | ^ filesystem | ||
| + | ^ Layer3 | ||
| + | ^ Size in KiB | 896 KiB | ||
| + | ^ Name | ||
| + | ^ <color magenta> | ||
| + | ^ filesystem | ||
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| - | <WRAP BOX> | + | * Connect serial as per the [[toh: |
| - | FIXME //The instructions below are for Broadcom devices | + | * Navigate to ' |
| - | **//Remove | + | * Upload the OpenWrt initramfs image, and wait till the switch reboots into OpenWrt. |
| + | | ||
| + | * Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it: < | ||
| + | | ||
| + | ==== Booting OpenWrt from RAM ==== | ||
| - | This section deals with | + | -> [[docs: |
| - | * How you install OpenWrt from a device freshly opened | + | |
| - | * The steps required such as reset to factory defaults if the device has already been configured | + | |
| - | **Note:** Reset router | + | The XGS1250-12 can boot from the network, but for that you'd need to manipulate the boot command. ZyXEL password protected the U-boot environment. However, if you change the bootcmd |
| - | * Browse | + | |
| - | * Upload .bin file to router | + | |
| - | * Wait for it to reboot | + | |
| - | * Telnet to 192.168.1.1 and set a root password, or browse to ''< | + | |
| - | </ | + | |
| - | ==== OEM installation using the TFTP method ==== | ||
| - | -> [[docs: | ||
| - | === Specific values needed for tftp === | + | === Specific values needed for TFTP === |
| - | <WRAP BOX> | + | ^ Bootloader TFTP server IPv4 address |
| + | ^ Firmware TFTP image | [[: | ||
| - | FIXME Enter values for " | + | === Instructions === |
| - | ^ Bootloader tftp server IPv4 address | + | |
| - | ^ Bootloader MAC address (special) | + | |
| - | ^ Firmware tftp image | [[:downloads|Latest OpenWrt release]] (**'' | + | |
| - | ^ TFTP transfer window | + | |
| - | ^ TFTP window start | approximately FILL-IN seconds after power on | | + | * Reboot |
| - | ^ TFTP client required IP address | + | * Load the ramdisk in the U-boot shell: < |
| - | + | ||
| - | </WRAP> | + | |
| ===== Upgrading OpenWrt ===== | ===== Upgrading OpenWrt ===== | ||
| Line 174: | Line 183: | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | FIXME Please fill in real values for this device, then remove the EXAMPLEs | ||
| ==== Network interfaces ==== | ==== Network interfaces ==== | ||
| The default network configuration is: | The default network configuration is: | ||
| ^ Interface Name ^ Description | ^ Interface Name ^ Description | ||
| - | | br-lan | + | | br-lan |
| - | | vlan0 (eth0.0) | + | |
| - | | vlan1 (eth0.1) | + | |
| - | | wl0 | EXAMPLE WiFi | EXAMPLE Disabled | + | |
| </ | </ | ||
| Line 272: | Line 277: | ||
| Layout is exactly the same as for the ZyXEL GS1900-10HP (casing color being black): | Layout is exactly the same as for the ZyXEL GS1900-10HP (casing color being black): | ||
| - | {{: | + | {{: |
| ^ Serial connection parameters for ZyXEL XGS1250-12 | 115200, 8N1 | | ^ Serial connection parameters for ZyXEL XGS1250-12 | 115200, 8N1 | | ||
| Line 297: | Line 302: | ||
| ==== OpenWrt bootlog ==== | ==== OpenWrt bootlog ==== | ||
| - | <WRAP bootlog> | + | <WRAP bootlog>< |
| - | < | + | U-Boot Version V1.0.0.2 (Aug 11 2020 - 14:10:19) |
| + | |||
| + | Board: RTL9300 CPU:800MHz LX:175MHz DDR: | ||
| + | DRAM: 128 MB | ||
| + | SPI-F: MXIC/ | ||
| + | Loading 65536B env. variables from offset 0xe0000 | ||
| + | Net: Net Initialization Skipped | ||
| + | No ethernet found. | ||
| + | 0 | ||
| + | ## Booting kernel from Legacy Image at 81000000 ... | ||
| + | Image Name: MIPS OpenWrt Linux-5.10.92 | ||
| + | | ||
| + | Image Type: MIPS Linux Kernel Image (gzip compressed) | ||
| + | Data Size: 6632884 Bytes = 6.3 MB | ||
| + | Load Address: 80000000 | ||
| + | Entry Point: | ||
| + | | ||
| + | | ||
| + | |||
| + | Starting kernel ... | ||
| + | |||
| + | [ 0.000000] Linux version 5.10.92 (1800x@crunchbot) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r18681+56-5d110c0161) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Mon Jan 31 12:58:24 2022 | ||
| + | [ 0.000000] RTL838X model is 0 | ||
| + | [ 0.000000] RTL839X model is 0 | ||
| + | [ 0.000000] RTL93XX model is 93021001 | ||
| + | [ 0.000000] SoC Type: RTL9302B | ||
| + | [ 0.000000] Kernel command line: | ||
| + | [ 0.000000] printk: bootconsole [early0] enabled | ||
| + | [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc) | ||
| + | [ 0.000000] MIPS: machine is Zyxel XGS1250-12 Switch | ||
| + | [ 0.000000] Initrd not found or empty - disabling initrd | ||
| + | [ 0.000000] Using appended Device Tree. | ||
| + | [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. | ||
| + | [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | ||
| + | [ 0.000000] Zone ranges: | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Movable zone start for each node | ||
| + | [ 0.000000] Early memory node ranges | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] | ||
| + | [ 0.000000] On node 0 totalpages: 32768 | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 | ||
| + | [ 0.000000] pcpu-alloc: [0] 0 | ||
| + | [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 | ||
| + | [ 0.000000] Kernel command line: console=ttyS0, | ||
| + | [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) | ||
| + | [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.000000] Writing ErrCtl register=0000000c | ||
| + | [ 0.000000] Readback ErrCtl register=0000000c | ||
| + | [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off | ||
| + | [ 0.000000] Memory: 113356K/ | ||
| + | [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, | ||
| + | [ 0.000000] NR_IRQS: 256 | ||
| + | [ 0.000000] random: get_random_bytes called from 0x8061eabc with crng_init=0 | ||
| + | [ 0.000000] CPU frequency from device tree: 800MHz | ||
| + | [ 0.000000] rtl9300_clockevent_init called for cpu0 | ||
| + | [ 0.000000] rtl9300_clockevent_init using IRQ 8 | ||
| + | [ 0.000000] clocksource: | ||
| + | [ 0.000010] sched_clock: | ||
| + | [ 0.008488] Calibrating delay loop... 531.66 BogoMIPS (lpj=2658304) | ||
| + | [ 0.067031] pid_max: default: 32768 minimum: 301 | ||
| + | [ 0.072219] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.080082] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.090634] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build | ||
| + | [ 0.101357] clocksource: | ||
| + | [ 0.112038] futex hash table entries: 256 (order: -1, 3072 bytes, linear) | ||
| + | [ 0.119455] pinctrl core: initialized pinctrl subsystem | ||
| + | [ 0.125513] NET: Registered protocol family 16 | ||
| + | [ 0.178077] clocksource: | ||
| + | [ 0.184660] NET: Registered protocol family 2 | ||
| + | [ 0.189534] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) | ||
| + | [ 0.197921] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.207062] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.215365] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.223006] TCP: Hash tables configured (established 1024 bind 1024) | ||
| + | [ 0.230044] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.237089] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.244969] NET: Registered protocol family 1 | ||
| + | [ 0.471604] workingset: timestamp_bits=14 max_order=15 bucket_order=1 | ||
| + | [ 0.482789] squashfs: version 4.0 (2009/ | ||
| + | [ 0.489137] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | ||
| + | [ 0.502014] realtek_gpio_probe probing RTL GPIO | ||
| + | [ 0.544029] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled | ||
| + | [ 0.552022] printk: console [ttyS0] disabled | ||
| + | [ 0.556658] 18002000.uart: | ||
| + | [ 0.566238] printk: console [ttyS0] enabled | ||
| + | [ 0.566238] printk: console [ttyS0] enabled | ||
| + | [ 0.575472] printk: bootconsole [early0] disabled | ||
| + | [ 0.575472] printk: bootconsole [early0] disabled | ||
| + | [ 0.805647] brd: module loaded | ||
| + | [ 0.812615] spi-nor spi0.0: mx25l12805d (16384 Kbytes) | ||
| + | [ 0.818484] 6 fixed-partitions partitions found on MTD device spi0.0 | ||
| + | [ 0.825550] Creating 6 MTD partitions on " | ||
| + | [ 0.830934] 0x000000000000-0x0000000e0000 : " | ||
| + | [ 0.838662] 0x0000000e0000-0x0000000f0000 : " | ||
| + | [ 0.845512] 0x0000000f0000-0x000000100000 : " | ||
| + | [ 0.854305] 0x000000100000-0x000000200000 : " | ||
| + | [ 0.860632] 0x000000200000-0x000000300000 : " | ||
| + | [ 0.868846] 0x000000300000-0x000001000000 : " | ||
| + | [ 0.885215] libphy: Fixed MDIO Bus: probed | ||
| + | [ 0.892068] Probing RTL838X eth device pdev: 82075800, dev: 82075810 | ||
| + | [ 0.918641] Found SoC ID: 9302: RTL9302B, family 9300 | ||
| + | [ 0.924284] Using MAC 000000e04c000000 | ||
| + | [ 0.928574] set sds port 24 to 6 | ||
| + | [ 0.932160] set sds port 25 to 7 | ||
| + | [ 0.935740] set sds port 26 to 8 | ||
| + | [ 0.939371] set sds port 27 to 9 | ||
| + | [ 0.943010] rtl838x_mdio_init Looking at port 0 | ||
| + | [ 0.948038] rtl838x_mdio_init phy mode of port 0 is qsgmii | ||
| + | [ 0.954170] rtl838x_mdio_init Looking at port 1 | ||
| + | [ 0.959260] rtl838x_mdio_init phy mode of port 1 is qsgmii | ||
| + | [ 0.965361] rtl838x_mdio_init Looking at port 2 | ||
| + | [ 0.970433] rtl838x_mdio_init phy mode of port 2 is qsgmii | ||
| + | [ 0.976526] rtl838x_mdio_init Looking at port 3 | ||
| + | [ 0.981596] rtl838x_mdio_init phy mode of port 3 is qsgmii | ||
| + | [ 0.987690] rtl838x_mdio_init Looking at port 4 | ||
| + | [ 0.992759] rtl838x_mdio_init phy mode of port 4 is qsgmii | ||
| + | [ 0.998896] rtl838x_mdio_init Looking at port 5 | ||
| + | [ 1.003929] rtl838x_mdio_init phy mode of port 5 is qsgmii | ||
| + | [ 1.010059] rtl838x_mdio_init Looking at port 6 | ||
| + | [ 1.015093] rtl838x_mdio_init phy mode of port 6 is qsgmii | ||
| + | [ 1.021222] rtl838x_mdio_init Looking at port 7 | ||
| + | [ 1.026258] rtl838x_mdio_init phy mode of port 7 is qsgmii | ||
| + | [ 1.032388] rtl838x_mdio_init Looking at port 24 | ||
| + | [ 1.037520] rtl838x_mdio_init phy mode of port 24 is usxgmii | ||
| + | [ 1.043842] rtl838x_mdio_init Looking at port 25 | ||
| + | [ 1.049013] rtl838x_mdio_init phy mode of port 25 is usxgmii | ||
| + | [ 1.055300] rtl838x_mdio_init Looking at port 26 | ||
| + | [ 1.060468] rtl838x_mdio_init phy mode of port 26 is usxgmii | ||
| + | [ 1.066755] rtl838x_mdio_init Looking at port 27 | ||
| + | [ 1.071931] rtl838x_mdio_init phy mode of port 27 is 10gbase-r | ||
| + | [ 1.078453] rtl838x_mdio_init Looking at port 28 | ||
| + | [ 1.083581] rtl838x_mdio_init phy mode of port 28 is internal | ||
| + | [ 1.090701] c45_mask: 000e0000 | ||
| + | [ 1.094109] libphy: rtl930x-eth-mdio: | ||
| + | [ 1.526126] REALTEK RTL9300 SERDES mdio-bus: | ||
| + | [ 1.534432] rtl9300_configure_serdes: | ||
| + | [ 1.544574] rtl9300_configure_serdes CMU BAND is 16 | ||
| + | [ 1.550039] rtl9300_sds_rst 31 | ||
| + | [ 1.573415] rtl9300_configure_serdes PATCHING SerDes 9 | ||
| + | [ 1.580195] rtl9300_phy_enable_10g_1g 1gbit phy: 00001140 | ||
| + | [ 1.586194] rtl9300_phy_enable_10g_1g 1gbit phy enabled: 00001140 | ||
| + | [ 1.593996] rtl9300_phy_enable_10g_1g 10gbit phy: 00002040 | ||
| + | [ 1.600125] rtl9300_phy_enable_10g_1g 10gbit phy after: 00002040 | ||
| + | [ 1.607799] rtl9300_phy_enable_10g_1g set medium: 00000000 | ||
| + | [ 1.613923] rtl9300_phy_enable_10g_1g set medium after: 00000002 | ||
| + | [ 1.640618] rtl9300_configure_serdes: | ||
| + | [ 1.650387] rtl9300_serdes_mac_link_config: | ||
| + | [ 1.660447] rtl9300_serdes_mac_link_config: | ||
| + | [ 1.688378] rtl9300_force_sds_mode --------------------- serdes 9 forcing to 0 ... | ||
| + | [ 1.696795] rtl9300_force_sds_mode: | ||
| + | [ 1.702163] rtl9300_force_sds_mode: | ||
| + | [ 1.710231] rtl9300_force_sds_mode --------------------- serdes 9 forcing to 0 ... | ||
| + | [ 1.718687] rtl9300_force_sds_mode: | ||
| + | [ 1.724108] rtl9300_force_sds_mode: | ||
| + | [ 2.548072] random: fast init done | ||
| + | [ 6.443249] rtl9300_force_sds_mode --------------------- serdes 9 forced to 1a DONE | ||
| + | [ 6.451796] start_1.1.1 initial value for sds 9 | ||
| + | [ 6.484843] end_1.1.1 -- | ||
| + | [ 6.487658] start_1.1.2 Load DFE init. value | ||
| + | [ 6.493429] end_1.1.2 | ||
| + | [ 6.495950] start_1.1.3 disable LEQ training, | ||
| + | [ 6.508370] end_1.1.3 -- | ||
| + | [ 6.511179] start_1.1.4 offset cali setting | ||
| + | [ 6.516818] end_1.1.4 | ||
| + | [ 6.519368] start_1.1.5 LEQ and DFE setting | ||
| + | [ 6.531031] end_1.1.5 | ||
| + | [ 6.540567] start_1.2.1 ForegroundOffsetCal_Manual | ||
| + | [ 6.547889] end_1.2.1 | ||
| + | [ 6.555904] start_1.2.3 Foreground Calibration | ||
| + | [ 6.569418] rtl9300_do_rx_calibration_2_3: | ||
| + | [ 6.578097] rtl9300_do_rx_calibration_2_3: | ||
| + | [ 6.583617] start_1.4.1 | ||
| + | [ 6.805235] end_1.4.1 | ||
| + | [ 6.807952] start_1.4.2 | ||
| + | [ 6.816494] vth_set_bin = 4 | ||
| + | [ 6.819250] vth_set_bin = 2 | ||
| + | [ 6.823352] Vth Maunal = 1 | ||
| + | [ 6.935280] Tap0 Sign : + | ||
| + | [ 6.938330] tap0_coef_bin = 20 | ||
| + | [ 6.942239] tap0 manual = 1 | ||
| + | [ 6.948649] end_1.4.2 | ||
| + | [ 6.951757] start_1.5.2 | ||
| + | [ 7.028187] end_1.5.2 | ||
| + | [ 7.115709] i2c /dev entries driver | ||
| + | [ 7.122354] rtl9300_i2c_probe probing I2C adapter | ||
| + | [ 7.127614] i2c-rtl9300 1b00036c.i2c-rtl9300: | ||
| + | [ 7.135221] rtl9300_i2c_probe scl_num 0 | ||
| + | [ 7.139522] rtl9300_i2c_probe sda_num 1 | ||
| + | [ 7.145623] NET: Registered protocol family 10 | ||
| + | [ 7.159285] Segment Routing with IPv6 | ||
| + | [ 7.163466] NET: Registered protocol family 17 | ||
| + | [ 7.168868] 8021q: 802.1Q VLAN Support v1.8 | ||
| + | [ 7.174308] libphy: SFP SMBus: probed | ||
| + | [ 7.178610] sfp sfp-p12: Host maximum power 1.0W | ||
| + | [ 7.516087] libphy: rtl838x slave mii: probed | ||
| + | [ 7.521088] rtl83xx_mdio_probe found port 0 | ||
| + | [ 7.525747] rtl83xx_mdio_probe found port 1 | ||
| + | [ 7.530441] rtl83xx_mdio_probe found port 2 | ||
| + | [ 7.535089] rtl83xx_mdio_probe found port 3 | ||
| + | [ 7.539773] rtl83xx_mdio_probe found port 4 | ||
| + | [ 7.544420] rtl83xx_mdio_probe found port 5 | ||
| + | [ 7.549103] rtl83xx_mdio_probe found port 6 | ||
| + | [ 7.553750] rtl83xx_mdio_probe found port 7 | ||
| + | [ 7.558446] rtl83xx_mdio_probe found port 24 | ||
| + | [ 7.563194] rtl83xx_mdio_probe found port 25 | ||
| + | [ 7.567933] rtl83xx_mdio_probe found port 26 | ||
| + | [ 7.572719] rtl83xx_mdio_probe found port 27 | ||
| + | [ 7.577466] rtl83xx_mdio_probe found port 28 | ||
| + | [ 7.595997] rtl93xx_setup called | ||
| + | [ 7.599683] In rtl83xx_vlan_setup | ||
| + | [ 7.603363] In rtl930x_vlan_profile_setup | ||
| + | [ 7.607813] In rtl930x_vlan_profile_setup | ||
| + | [ 7.612315] UNKNOWN_MC_PMASK: | ||
| + | [ 7.617255] VLAN 0: L2 learn: 0; Unknown MC PMasks: L2 1fffffff, IPv4 1fffffff, IPv6: 1fffffff | ||
| + | [ 7.617262] | ||
| + | [ 7.634429] | ||
| + | [ 7.639891] VLAN profile 0: raw 00033000 00000000 1fffffff 1fffffff 1fffffff | ||
| + | [ 8.718087] rtl83xx_enable_phy_polling: | ||
| + | [ 8.723997] rtl930x_pie_init | ||
| + | [ 8.728271] rtl83xx-switch switch@1b000000 lan1 (uninitialized): | ||
| + | [ 8.742078] rtl83xx-switch switch@1b000000 lan2 (uninitialized): | ||
| + | [ 8.755837] rtl83xx-switch switch@1b000000 lan3 (uninitialized): | ||
| + | [ 8.769543] rtl83xx-switch switch@1b000000 lan4 (uninitialized): | ||
| + | [ 8.783353] rtl83xx-switch switch@1b000000 lan5 (uninitialized): | ||
| + | [ 8.797163] rtl83xx-switch switch@1b000000 lan6 (uninitialized): | ||
| + | [ 8.810973] rtl83xx-switch switch@1b000000 lan7 (uninitialized): | ||
| + | [ 8.824793] rtl83xx-switch switch@1b000000 lan8 (uninitialized): | ||
| + | [ 8.840035] Aquantia AQR113C mdio-bus: | ||
| + | [ 8.849761] rtl83xx-switch switch@1b000000 lan9 (uninitialized): | ||
| + | [ 8.865016] Aquantia AQR113C mdio-bus: | ||
| + | [ 8.874742] rtl83xx-switch switch@1b000000 lan10 (uninitialized): | ||
| + | [ 8.889999] Aquantia AQR113C mdio-bus: | ||
| + | [ 8.899776] rtl83xx-switch switch@1b000000 lan11 (uninitialized): | ||
| + | [ 8.913951] rtl83xx-switch switch@1b000000: | ||
| + | [ 8.922649] rtl93xx_phylink_mac_config port 28, mode 1, phy-mode: internal, speed 10000, link 0 | ||
| + | [ 8.932693] DSA: tree 0 setup | ||
| + | [ 8.936036] LINK state irq: 23 | ||
| + | [ 8.939522] In rtl83xx_setup_qos | ||
| + | [ 8.943162] L3_IPUC_ROUTE_CTRL 00002000, IPMC_ROUTE 00000500, IP6UC_ROUTE 00014580, IP6MC_ROUTE 00012880 | ||
| + | [ 8.953740] L3_IPUC_ROUTE_CTRL 00002001, IPMC_ROUTE 00000501, IP6UC_ROUTE 00014581, IP6MC_ROUTE 00012881 | ||
| + | [ 8.964314] L3_IP_ROUTE_CTRL 00000130 | ||
| + | [ 8.968507] rtl930x_dbgfs_init called | ||
| + | [ 9.025314] Freeing unused kernel memory: 9928K | ||
| + | [ 9.030419] This architecture does not have kernel memory protection. | ||
| + | [ 9.037587] Run /init as init process | ||
| + | [ 9.041686] | ||
| + | [ 9.044982] | ||
| + | [ 9.047492] | ||
| + | [ 9.051004] | ||
| + | [ 9.053618] | ||
| + | [ 9.056798] rtl93xx_phylink_mac_config port 28, mode 1, phy-mode: internal, speed 10000, link 1 | ||
| + | [ 9.066550] rtl83xx-switch switch@1b000000: | ||
| + | [ 9.075508] rtl83xx_fib_event_work_do: | ||
| + | [ 9.787289] init: Console is alive | ||
| + | [ 9.791653] init: - watchdog - | ||
| + | [ 9.808811] kmodloader: loading kernel modules from / | ||
| + | [ 9.819555] kmodloader: done loading kernel modules from / | ||
| + | [ 9.838290] init: - preinit - | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | Press the [f] key and hit [enter] to enter failsafe mode | ||
| + | Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | Please press Enter to activate this console. | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | |||
| + | |||
| + | |||
| + | BusyBox v1.35.0 (2022-01-31 12:30:10 UTC) built-in shell (ash) | ||
| + | |||
| + | _______ | ||
| + | | ||
| + | | ||
| + | | ||
| + | |__| W I R E L E S S F R E E D O M | ||
| + | | ||
| + | | ||
| + | | ||
| + | | ||
| + | |||
| + | === WARNING! ===================================== | ||
| + | There is no root password defined on this device! | ||
| + | Use the " | ||
| + | in order to prevent unauthorized SSH logins. | ||
| + | -------------------------------------------------- | ||
| + | root@OpenWrt:/ | ||
| + | </ | ||
| </ | </ | ||
| ===== Notes ===== | ===== Notes ===== | ||
| * SFP+ cage does not work yet on OpenWrt. | * SFP+ cage does not work yet on OpenWrt. | ||
| - | * 10GbE RJ-45 interfaces are said to work but I have not been able to get them going on OpenWrt. Worked fine on OEM firmware with short CAT5E cables and X550-AT2 at the other end. | + | * The network needs to be initialised by the bootloader through the '' |
| ===== Tags ===== | ===== Tags ===== | ||
| [[meta: | [[meta: | ||
| - | {{tag> | + | {{tag> |