Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:zyxel:wap3205 [2015/10/18 15:22] – ↷ Links adapted because of a move operation tmomas | toh:zyxel:wap3205 [2019/10/17 20:29] – Datatables added, cleanup tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== ZyXEL WAP3205 ====== | ||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ===== Supported Versions ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| + | headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data | ||
| + | align : c, | ||
| + | filter | ||
| + | sort : Version | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| + | header | ||
| + | align : c, | ||
| + | filter | ||
| + | sort : Version | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : c,c,c | ||
| + | filter | ||
| + | sort : Version | ||
| + | ---- | ||
| + | |||
| + | -> [[docs: | ||
| + | |||
| + | The board is the same one used on the [[toh: | ||
| + | |||
| + | Support for the [[toh: | ||
| + | |||
| + | You should obtain ''< | ||
| + | |||
| + | The only issue is that the Switch/VLAN configurations let you configure even the ports that are actually unpopulated on the PCB, and obviously LuCI will show the wrong model on the webadmin. | ||
| + | |||
| + | The rest of the installation process is the same as the [[toh: | ||
| + | |||
| + | |||
| + | ===== Hardware ===== | ||
| + | ==== Info ==== | ||
| + | ^ Architecture | ||
| + | ^ Vendor | ||
| + | ^ Bootloader | ||
| + | ^ System-On-Chip | ||
| + | ^ CPU Speed | 384 MHz | | ||
| + | ^ Flash size | 4 MiB | | ||
| + | ^ RAM | 32 MiB | | ||
| + | ^ USB | No (Not populated) | ||
| + | ^ Serial | ||
| + | ^ JTAG | [[# | ||
| + | |||
| + | ==== Opening the case ==== | ||
| + | **Note:** This will void your warranty! | ||
| + | |||
| + | * To remove the cover simply remove the two screws on the bottom. Then just open it. | ||
| + | * The board itself has no screws. | ||
| + | |||
| + | ==== Serial ==== | ||
| + | The are 4 pins on the board marked as follows: | ||
| + | |||
| + | - RX | ||
| + | - GND | ||
| + | - TX | ||
| + | - 3V3 | ||
| + | |||
| + | {{media: | ||
| + | |||
| + | ==== JTAG ==== | ||
| + | -> [[docs: | ||
| + | |||
| + | How to connect to the JTAG Port of this specific device:\\ | ||
| + | **Insert photo of PCB with markings for JTAG port** | ||
| + | |||
| + | ===== Bootloader ===== | ||
| + | |||
| + | The bootloader used in this unit is U-Boot. It is available through the serial interface with the settings: 57600/N/1 \\ | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||