Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:zyxel:wap3205 [2015/09/25 20:26] – Picture link corrected + resized tmomastoh:zyxel:wap3205 [2019/10/17 20:29] – Datatables added, cleanup tmomas
Line 1: Line 1:
 +====== ZyXEL WAP3205 ======
  
 +{{:media:zyxel:wap3205_general_view.png?direct&300}}
 +{{:media:zyxel:wap3205_v2_general_view.png?direct&300|}}
 +
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid
 +headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,c,c,c,c,c,c
 +filter  : Model=WAP3205
 +sort    : Version
 +----
 +
 +
 +===== Hardware Highlights =====
 +---- datatable ----
 +cols    : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_
 +header  : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB
 +align   : c,c,c,c,c,c,c,c,c,c,c,c,c
 +filter  : Model=WAP3205
 +sort    : Version
 +----
 +
 +
 +===== Installation =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock
 +align   : c,c,c
 +filter  : Model=WAP3205
 +sort    : Version
 +----
 +
 +-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
 +
 +The board is the same one used on the [[toh:zyxel:nbg419n|ZyXEL NBG-419N]], but has 2 Ethernet ports instead of 4 LAN + 1 WAN. (and has no WiFi on/off switch)
 +
 +Support for the [[toh:zyxel:nbg419n|ZyXEL NBG-419N]] appeared in r28078, so you can download an Attitude Adjustment (12.09 final) ''openwrt-ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin'' image or you can build from the source. See [[docs:guide-developer:build-system:start]]. Select ''Ralink RT288x/RT305x'' as ''Target System'' and ''RT305x based boards'' as ''Subtarget'' in ''make menuconfig''.
 +
 +You should obtain ''<buildroot dir>/bin/ramips/openwrt-ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin''.
 +
 +The only issue is that the Switch/VLAN configurations let you configure even the ports that are actually unpopulated on the PCB, and obviously LuCI will show the wrong model on the webadmin.
 +
 +The rest of the installation process is the same as the [[toh:zyxel:nbg419n|ZyXEL NBG-419N]].
 +
 +
 +===== Hardware =====
 +==== Info ====
 +^ Architecture     | MIPS                                       |
 +^ Vendor           | Ralink                                     |
 +^ Bootloader       | [[docs:techref:bootloader:uboot|U-Boot]]   |
 +^ System-On-Chip   | Ralink RT3052                              |
 +^ CPU Speed        | 384 MHz                                    |
 +^ Flash size       | 4 MiB                                      |
 +^ RAM              | 32 MiB                                     |
 +^ USB              | No (Not populated)                         |
 +^ Serial           | [[#Serial|Yes]]                            |
 +^ JTAG             | [[#JTAG|Yes]]                              |
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +  * To remove the cover simply remove the two screws on the bottom. Then just open it.
 +  * The board itself has no screws.
 +
 +==== Serial ====
 +The are 4 pins on the board marked as follows:
 +
 +  - RX
 +  - GND
 +  - TX
 +  - 3V3
 +
 +{{media:zyxel:wap3205.jpg?400|}}
 +
 +==== JTAG ====
 +-> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +How to connect to the JTAG Port of this specific device:\\
 +**Insert photo of PCB with markings for JTAG port**
 +
 +===== Bootloader =====
 +
 +The bootloader used in this unit is U-Boot. It is available through the serial interface with the settings: 57600/N/1 \\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>ramips rt3052 4flash 32ram}}
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1