Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:zyxel:wap3205 [2014/07/10 23:50] – created lucenttoh:zyxel:wap3205 [2019/10/17 20:29] – Datatables added, cleanup tmomas
Line 1: Line 1:
 +====== ZyXEL WAP3205 ======
  
 +{{:media:zyxel:wap3205_general_view.png?direct&300}}
 +{{:media:zyxel:wap3205_v2_general_view.png?direct&300|}}
 +
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid
 +headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,c,c,c,c,c,c
 +filter  : Model=WAP3205
 +sort    : Version
 +----
 +
 +
 +===== Hardware Highlights =====
 +---- datatable ----
 +cols    : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_
 +header  : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB
 +align   : c,c,c,c,c,c,c,c,c,c,c,c,c
 +filter  : Model=WAP3205
 +sort    : Version
 +----
 +
 +
 +===== Installation =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock
 +align   : c,c,c
 +filter  : Model=WAP3205
 +sort    : Version
 +----
 +
 +-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
 +
 +The board is the same one used on the [[toh:zyxel:nbg419n|ZyXEL NBG-419N]], but has 2 Ethernet ports instead of 4 LAN + 1 WAN. (and has no WiFi on/off switch)
 +
 +Support for the [[toh:zyxel:nbg419n|ZyXEL NBG-419N]] appeared in r28078, so you can download an Attitude Adjustment (12.09 final) ''openwrt-ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin'' image or you can build from the source. See [[docs:guide-developer:build-system:start]]. Select ''Ralink RT288x/RT305x'' as ''Target System'' and ''RT305x based boards'' as ''Subtarget'' in ''make menuconfig''.
 +
 +You should obtain ''<buildroot dir>/bin/ramips/openwrt-ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin''.
 +
 +The only issue is that the Switch/VLAN configurations let you configure even the ports that are actually unpopulated on the PCB, and obviously LuCI will show the wrong model on the webadmin.
 +
 +The rest of the installation process is the same as the [[toh:zyxel:nbg419n|ZyXEL NBG-419N]].
 +
 +
 +===== Hardware =====
 +==== Info ====
 +^ Architecture     | MIPS                                       |
 +^ Vendor           | Ralink                                     |
 +^ Bootloader       | [[docs:techref:bootloader:uboot|U-Boot]]   |
 +^ System-On-Chip   | Ralink RT3052                              |
 +^ CPU Speed        | 384 MHz                                    |
 +^ Flash size       | 4 MiB                                      |
 +^ RAM              | 32 MiB                                     |
 +^ USB              | No (Not populated)                         |
 +^ Serial           | [[#Serial|Yes]]                            |
 +^ JTAG             | [[#JTAG|Yes]]                              |
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +  * To remove the cover simply remove the two screws on the bottom. Then just open it.
 +  * The board itself has no screws.
 +
 +==== Serial ====
 +The are 4 pins on the board marked as follows:
 +
 +  - RX
 +  - GND
 +  - TX
 +  - 3V3
 +
 +{{media:zyxel:wap3205.jpg?400|}}
 +
 +==== JTAG ====
 +-> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +How to connect to the JTAG Port of this specific device:\\
 +**Insert photo of PCB with markings for JTAG port**
 +
 +===== Bootloader =====
 +
 +The bootloader used in this unit is U-Boot. It is available through the serial interface with the settings: 57600/N/1 \\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>ramips rt3052 4flash 32ram}}
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1