Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:zyxel:vmg1312-b30a [2019/10/17 20:22] – unsupported tag added tmomastoh:zyxel:vmg1312-b30a [2020/03/08 23:51] – [Tags] sam0815
Line 9: Line 9:
 ^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ ^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
 | BCM63168@400MHz | 64MiB | 128MiB | 4 x | 1 x 2.0| Yes (4-Pin) | Yes| | BCM63168@400MHz | 64MiB | 128MiB | 4 x | 1 x 2.0| Yes (4-Pin) | Yes|
- 
-===== Basic configuration ===== 
--> [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]] After flashing, proceed with this.\\ 
-Set up your Internet connection, configure wireless, configure USB port, etc. 
- 
- 
-===== Specific Configuration ===== 
- 
- 
- 
-==== Failsafe mode ==== 
--> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset]] 
- 
  
 ^ INFO           ^ ^ ^ INFO           ^ ^
Line 44: Line 31:
 | Antenna        | Internal (2x) | | Antenna        | Internal (2x) |
 | Power          | 12V / 1A      | | Power          | 12V / 1A      |
 +
 +===== Basic configuration =====
 +-> [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]] After flashing, proceed with this.\\
 +Set up your Internet connection, configure wireless, configure USB port, etc.
 +
 +
 +===== Specific Configuration =====
 +
 +=== Vendor Flash ====
 +
 +The vendor flashformat shows:
 +
 +> $ binwalk 1.00\(AATO.11\)C0.bin                                                                                                       
 +>                                                                                                                                                                       
 +> DECIMAL       HEXADECIMAL     DESCRIPTION                                                                                                                             
 +> --------------------------------------------------------------------------------                                                                                      
 +> 131072        0x20000         JFFS2 filesystem, big endian 
 +
 +=== firmware upgrade via bootloader web-ui ===
 +
 +> CFE> 
 +> web info: Waiting for connection on socket 0.
 +> web info: Upload 17712031 bytes, Broadcom image format.
 +> web info: Waiting for connection on socket 1.
 +
 +> Flashing root file system and kernel at 0xb8020000: > ........................................................................................................................................
 +>
 +> *** Image flash done *** !
 +
 +> Resetting board...
 +==== Failsafe mode ====
 +-> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset]]
 +
  
 ==== Photos ==== ==== Photos ====
Line 58: Line 78:
 **Photo of PCB** **Photo of PCB**
  
 +==== Serial Connection ====
 +
 +The Pinout ist the same as for the [[toh/zyxel/zyxel_vmg5313-b30a]]
 +
 +Pinout:
 +[ 3,3 V - Tx - Rx - NC - GND ]
 +
 +^ Serial connection parameters\\ for ZyXEL VMG1312-B30A | 115200, 8N1 |
  
 ===== Bootlogs ===== ===== Bootlogs =====
Line 367: Line 395:
 ===== Notes ===== ===== Notes =====
  
 +==== CFE-Bootloader ====
 +
 +CFE-Bootloader has Web-ui for flash-recovery (http://192.168.1.1), just stop autoboot
 +
 +<WRAP bootlog>
 +<nowiki>
 +CFE version 1.0.38-112.12 for BCM963268 (32bit,SP,BE)
 +Build Date: 05/21/2012 (zongyue@MsgSW4-SerVer)
 +Copyright (C) 2000-2011 Broadcom Corporation.
 +
 +NAND flash device: name Samsung K9F1G08U0D, id 0xecf1 block 128KB size 131072KB
 +Chip ID: BCM63168C0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 67108864 bytes (64MB)
 +Boot Address: 0xb8000000
 +
 +Checking Reset button on EXT INTR 0 
 +Board IP address                  : 192.168.1.1:ffffff00  
 +Host IP address                   : 192.168.1.100  
 +Gateway IP address                :   
 +Run from flash/host (f/h)         : f  
 +Default host run file name        : vmlinux  
 +Default host flash file name      : bcm963xx_fs_kernel  
 +Boot delay (0-9 seconds)          : 1  
 +Boot image (0=latest, 1=previous) : 0  
 +Board Id (0-6)                    : 963168VX  
 +Number of MAC Addresses (1-32)    : 12  
 +Base MAC Address                  : b0:b2:dc:f2:56:6c  
 +PSI Size (1-128) KBytes           : 64  
 +Enable Backup PSI [0|1]           : 0  
 +System Log Size (0-256) KBytes    : 0  
 +Main Thread Number [0|1]          : 0  
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 1
 +web info: Waiting for connection on socket 0.␛[J
 +CFE> athe
 +Available commands:
 +
 +ATSE                show the seed of password generator
 +ATEN                set BootExtension Debug Flag
 +ATCR                Clear console screen
 +ATSH                dump manufacturer related data in ROM
 +ATUR                xmodem upload router firmware to flash ROM
 +ATIR                Set ImageDefault to ROM-D partition
 +ATER                Erase ROM-D partition
 +ATBL                Print boot line and board parameter info
 +ATDU                Dump memory or registers.
 +ATBR                Reset to default Romfile
 +ATGO                boot router
 +ATSR                system reboot
 +ATMB                Use for multiboot.
 +ATHE                print help
 +
 +For more information about a command, enter 'help command-name'
 +*** command status = 0
 +CFE> 
 +CFE> atbl
 +Board IP address                  : 192.168.1.1:ffffff00  
 +Host IP address                   : 192.168.1.100  
 +Gateway IP address                :   
 +Run from flash/host (f/h)         : f  
 +Default host run file name        : vmlinux  
 +Default host flash file name      : bcm963xx_fs_kernel  
 +Boot delay (0-9 seconds)          : 1  
 +Boot image (0=latest, 1=previous) : 0  
 +Board Id (0-6)                    : 963168VX  
 +Number of MAC Addresses (1-32)    : 12  
 +Base MAC Address                  : b0:b2:dc:f2:56:6c  
 +PSI Size (1-128) KBytes           : 64  
 +Enable Backup PSI [0|1]           : 0  
 +System Log Size (0-256) KBytes    : 0  
 +Main Thread Number [0|1]          : 0  
 +
 +*** command status = 0
 +CFE> 
 +web info: Waiting for connection on socket 1.␛[J
 +web warning: Unexpected TCP disconnect.␛[J
 +web warning: Unexpected TCP disconnect.␛[J
 +web info: Waiting for connection on socket 0.␛[J
 +web info: Waiting for connection on socket 1.␛[J
 +web warning: Unexpected TCP disconnect.␛[J
 +web info: Waiting for connection on socket 0.␛[J
 +web info: Waiting for connection on socket 1.␛[J
 +CFE> atsh
 +
 +FW       Version       : V1.00(AAEB.5)
 +Bootbase Version       : V1.52 | 05/21/2012 12:24:58
 +Vendor Name            : ZyXEL Technology Corp.
 +Product Model          : VMG1312-B30A
 +Serial Number          : S120Y3305xxxx
 +First MAC Address      : B0B2DCF256xx
 +Last MAC Address       : B0B2DCF256xx
 +MAC Address Quantity   : 12
 +Default Country Code   : ED
 +Boot Module Debug Flag : 00
 +RootFS      Checksum   : 07ea8753
 +ImageDefaultChecksum   : 229f5a77
 +Main Feature Bits      : 00
 +Other Feature Bits     :
 +                4d 53 40 13 00 00 00 00-00 00 00 00 00 00 00 00 
 +                00 00 00 00 00 00 00 00-00 00 00 00 00 00 
 +
 +*** command status = 0
 +</nowiki>
 +</WRAP>\\
  
 ===== Tags ===== ===== Tags =====
 [[meta:tags|How to add tags]] [[meta:tags|How to add tags]]
-{{tag>bcm63168 GigabitEthernet FastEthernet 1NIC 1WNIC 5Port USB 2USB ath9k DetachableAntenna 32RAM 8Flash MIPS MIPS32 34K 12v_powered unsupported}}+{{tag>bcm63168 FastEthernet 1NIC 1WNIC 5Port USB 2USB ath9k DetachableAntenna 64RAM 8Flash MIPS MIPS32 34K vDSL2+ 12v_powered unsupported}}
  • Last modified: 2021/01/12 18:50
  • by danitool