| Next revision | Previous revision Next revisionBoth sides next revision |
| toh:zyxel:vmg1312-b30a [2015/11/30 21:14] – [[meta:tags]] -> [[meta:tags|How to add tags]] tmomas | toh:zyxel:vmg1312-b30a [2020/03/08 23:51] – [Tags] sam0815 |
|---|
| | ====== ZyXEL VMG1312-B30A ====== |
| | ADSL2/VDSL2 Modem router based on Broadcom BCM63168 chip. |
| |
| | ===== Supported Versions ===== |
| | ^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^ |
| | NOT SUPPORTED YET |
| | |
| | ===== Hardware Highlights ===== |
| | ^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ |
| | | BCM63168@400MHz | 64MiB | 128MiB | 4 x | 1 x 2.0| Yes (4-Pin) | Yes| |
| | |
| | ^ INFO ^ ^ |
| | | Architecture | MIPS32 | |
| | | Vendor | Broadcom | |
| | | Model Name / ID| ZyXEL VMG1312-B30A / 963168VX | |
| | | Bootloader | CFE (1.0.38-112.12) | |
| | | System-On-Chip | Broadcom BCM63168 xDSL IAD SoC | |
| | | CPU / Speed | Broadcom MIPS 4350 V8.0 32-bit (SoC) / 400 MHz Dual Core | |
| | | Flash-Chip | Samsung K9F1G08U0D NAND Flash Memory (128M x 8bit) | |
| | | Flash-Size | 128 MiB | |
| | | RAM-Chip | Winbond W9751G6KB-25 DDR2-800 SDRAM (8M x 4 x 16bit) | |
| | | RAM-Size | 64 MiB | |
| | | VDSL2 Line Driver | Broadcom BCM6302 KMLG P10 | |
| | | Modem Transformer | MNC EP-339SG | |
| | | Ethernet | 4 x Broadcom BCM63168C0 + 1 x RJ-45 port for ADSL2+/VDSL Broadcom BCM3168C0 | |
| | | LAN-Transformer | 2 x MDF2008D Dual Port 10/100M | |
| | | Wireless| Broadcom BCM435f 802.11 b/g/n Wireless Controller (SoC integrated) | |
| | | USB | Yes, 1 x 2.0 (Broadcom BCM3168C0, SoC integrated)| |
| | | Serial | Yes (4-Pin) | |
| | | JTAG | Yes (MIPS EJTAG JTAG 14-pin header pinout) | |
| | | Antenna | Internal (2x) | |
| | | Power | 12V / 1A | |
| | |
| | ===== Basic configuration ===== |
| | -> [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]] After flashing, proceed with this.\\ |
| | Set up your Internet connection, configure wireless, configure USB port, etc. |
| | |
| | |
| | ===== Specific Configuration ===== |
| | |
| | === Vendor Flash ==== |
| | |
| | The vendor flashformat shows: |
| | |
| | > $ binwalk 1.00\(AATO.11\)C0.bin |
| | > |
| | > DECIMAL HEXADECIMAL DESCRIPTION |
| | > -------------------------------------------------------------------------------- |
| | > 131072 0x20000 JFFS2 filesystem, big endian |
| | |
| | === firmware upgrade via bootloader web-ui === |
| | |
| | > CFE> |
| | > web info: Waiting for connection on socket 0. |
| | > web info: Upload 17712031 bytes, Broadcom image format. |
| | > web info: Waiting for connection on socket 1. |
| | > |
| | > Flashing root file system and kernel at 0xb8020000: > ........................................................................................................................................ |
| | > |
| | > *** Image flash done *** ! |
| | > |
| | > Resetting board... |
| | ==== Failsafe mode ==== |
| | -> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset]] |
| | |
| | |
| | ==== Photos ==== |
| | Model Number |
| | |
| | //Front:// |
| | |
| | **Photo of front of the casing** |
| | |
| | //Back:// |
| | |
| | **Photo of back of the casing** |
| | |
| | **Photo of PCB** |
| | |
| | ==== Serial Connection ==== |
| | |
| | The Pinout ist the same as for the [[toh/zyxel/zyxel_vmg5313-b30a]] |
| | |
| | Pinout: |
| | [ 3,3 V - Tx - Rx - NC - GND ] |
| | |
| | ^ Serial connection parameters\\ for ZyXEL VMG1312-B30A | 115200, 8N1 | |
| | |
| | ===== Bootlogs ===== |
| | |
| | <WRAP bootlog> |
| | <nowiki><5>Linux version 2.6.30 (kuanjung@MSGSW4-server2) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Tue Apr 9 19:12:55 CST 2013 |
| | <4>NAND flash device: name Samsung K9F1G08U0D, id 0xecf1 block 128KB size 131072KB |
| | <4>963168VX prom init |
| | <6>CPU revision is: 0002a080 (Broadcom4350) |
| | <4>DSL SDRAM reserved: 0x132000 |
| | <6>Determined physical RAM map: |
| | <6> memory: 03ece000 @ 00000000 (usable) |
| | <4>Zone PFN ranges: |
| | <4> DMA 0x00000000 -> 0x00001000 |
| | <4> Normal 0x00001000 -> 0x00003ece |
| | <4>Movable zone start PFN for each node |
| | <4>early_node_map[1] active PFN ranges |
| | <4> 0: 0x00000000 -> 0x00003ece |
| | <7>On node 0 totalpages: 16078 |
| | <7>free_area_init_node: node 0, pgdat 80423d90, node_mem_map 81000000 |
| | <7> DMA zone: 32 pages used for memmap |
| | <7> DMA zone: 0 pages reserved |
| | <7> DMA zone: 4064 pages, LIFO batch:0 |
| | <7> Normal zone: 94 pages used for memmap |
| | <7> Normal zone: 11888 pages, LIFO batch:1 |
| | <4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 |
| | <5>Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 |
| | <4>wait instruction: enabled |
| | <4>Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. |
| | <4>Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes |
| | <6>NR_IRQS:128 |
| | <4>PID hash table entries: 256 (order: 8, 1024 bytes) |
| | <6>console [ttyS0] enabled |
| | <6>Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) |
| | <6>Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) |
| | <6>Memory: 58536k/64312k available (3306k kernel code, 5756k reserved, 823k data, 152k init, 0k highmem) |
| | <6>Calibrating delay loop... 398.33 BogoMIPS (lpj=199168) |
| | <4>Mount-cache hash table entries: 512 |
| | <6>--Kernel Config-- |
| | <6> SMP=1 |
| | <6> PREEMPT=1 |
| | <6> DEBUG_SPINLOCK=0 |
| | <6> DEBUG_MUTEXES=0 |
| | <4>Broadcom Logger v0.1 Apr 9 2013 19:10:21 |
| | <6>CPU revision is: 0002a080 (Broadcom4350) |
| | <4>Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. |
| | <4>Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes |
| | <6>Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) |
| | <6>Brought up 2 CPUs |
| | <6>net_namespace: 1140 bytes |
| | <6>NET: Registered protocol family 16 |
| | <4>registering PCI controller with io_map_base unset |
| | <4>registering PCI controller with io_map_base unset |
| | <4>bio: create slab <bio-0> at 0 |
| | <5>SCSI subsystem initialized |
| | <6>usbcore: registered new interface driver usbfs |
| | <6>usbcore: registered new interface driver hub |
| | <6>usbcore: registered new device driver usb |
| | <7>pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] |
| | <7>pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] |
| | <7>pci 0000:00:00.0: supports D1 D2 |
| | <6>pci 0000:00:00.0: PME# supported from D0 D3hot D3cold |
| | <6>pci 0000:00:00.0: PME# disabled |
| | <7>pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] |
| | <7>pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] |
| | <6>pci 0000:01:00.0: PME# supported from D0 D3hot |
| | <6>pci 0000:01:00.0: PME# disabled |
| | <6>pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 |
| | <6>pci 0000:01:00.0: IO window: disabled |
| | <6>pci 0000:01:00.0: MEM window: disabled |
| | <6>pci 0000:01:00.0: PREFETCH window: disabled |
| | <7>PCI: Setting latency timer of device 0000:01:00.0 to 64 |
| | <4>BLOG v3.0 Initialized |
| | <4>BLOG Rule v1.0 Initialized |
| | <4>Broadcom IQoS v0.1 Apr 9 2013 19:12:37 initialized |
| | <4>Broadcom GBPM v0.1 Apr 9 2013 19:12:38 initialized |
| | <6>NET: Registered protocol family 8 |
| | <6>NET: Registered protocol family 20 |
| | <6>NET: Registered protocol family 2 |
| | <6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes) |
| | <6>TCP established hash table entries: 2048 (order: 2, 16384 bytes) |
| | <6>TCP bind hash table entries: 2048 (order: 2, 16384 bytes) |
| | <6>TCP: Hash tables configured (established 2048 bind 2048) |
| | <6>TCP reno registered |
| | <6>NET: Registered protocol family 1 |
| | <6>JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. |
| | <6>fuse init (API version 7.11) |
| | <6>msgmni has been set to 114 |
| | <6>io scheduler noop registered (default) |
| | <7>PCI: Setting latency timer of device 0000:01:00.0 to 64 |
| | <4>Driver 'sd' needs updating - please use bus_type methods |
| | <6>PPP generic driver version 2.4.2 |
| | <6>PPP Deflate Compression module registered |
| | <6>PPP BSD Compression module registered |
| | <6>NET: Registered protocol family 24 |
| | <6>Broadcom DSL NAND controller (BrcmNand Controller) |
| | <4>-->brcmnand_scan: CS=0, numchips=1, csi=0 |
| | <6>mtd->oobsize=0, mtd->eccOobSize=0 |
| | <4>NAND_CS_NAND_XOR=00000000 |
| | <4>Disabling XOR on CS#0 |
| | <4>brcmnand_scan: Calling brcmnand_probe for CS=0 |
| | <4>B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 |
| | <4>brcmnand_read_id: CS0: dev_id=ecf10095 |
| | <4>After: NandSelect=40000001, nandConfig=15142200 |
| | <4>Block size=00020000, erase shift=17 |
| | <6>NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 |
| | <6>busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff |
| | <4>timing1 not adjusted: 6574845b |
| | <4>timing2 not adjusted: 00001e96 |
| | <4>brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 |
| | <6>BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0 |
| | <6>Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=ecf10095, tim1=6574845b, tim2=00001e96 |
| | <6>BrcmNAND version = 0x0400 128MB @00000000 |
| | <4>brcmnand_scan: Done brcmnand_probe |
| | <4>brcmnand_scan: B4 nand_select = 40000001 |
| | <4>brcmnand_scan: After nand_select = 40000001 |
| | <4>100 CS=0, chip->ctrl->CS[0]=0 |
| | <4>ECC level 15, threshold at 1 bits |
| | <4>reqEccLevel=0, eccLevel=15 |
| | <4>190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 |
| | <4>brcmnand_scan 10 |
| | <4>200 CS=0, chip->ctrl->CS[0]=0 |
| | <4>200 chip->ecclevel=15, acc=f7ff1010 |
| | <6>page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 |
| | <4>brcmnand_scan 220 |
| | <6>Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 |
| | <4>brcmnand_scan 230 |
| | <4>brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 |
| | <4>brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 |
| | <4>ECC layout=brcmnand_oob_bch4_4k |
| | <6>brcmnand_scan: mtd->oobsize=64 |
| | <6>brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 |
| | <6>brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 |
| | <4>300 CS=0, chip->ctrl->CS[0]=0 |
| | <4>500 chip=83a42990, CS=0, chip->ctrl->CS[0]=0 |
| | <4>-->brcmnand_default_bbt |
| | <4>brcmnand_default_bbt: bbt_td = bbt_main_descr |
| | <7>Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 |
| | <7>Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 |
| | <4>File system address: 0xbc020000 |
| | <6>brcmnandCET: Status -> Deferred |
| | <4>brcmnand_scan 99 |
| | <4>Root file system size 3aa0000 |
| | <4>bad block number = 0 |
| | <5>Creating 3 MTD partitions on "brcmnand.0": |
| | <5>0x000004020000-0x000004e80000 : "rootfs" |
| | <5>0x000007b00000-0x000007f00000 : "data" |
| | <5>0x000000000000-0x000000020000 : "nvram" |
| | <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver |
| | <4>PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) |
| | <7>PCI: Setting latency timer of device 0000:00:0a.0 to 64 |
| | <6>ehci_hcd 0000:00:0a.0: EHCI Host Controller |
| | <6>ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 |
| | <4>ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM |
| | <6>ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 |
| | <6>ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 |
| | <6>usb usb1: configuration #1 chosen from 1 choice |
| | <6>hub 1-0:1.0: USB hub found |
| | <6>hub 1-0:1.0: 2 ports detected |
| | <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver |
| | <4>PCI: Enabling device 0000:00:09.0 (0000 -> 0002) |
| | <7>PCI: Setting latency timer of device 0000:00:09.0 to 64 |
| | <6>ohci_hcd 0000:00:09.0: OHCI Host Controller |
| | <6>ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 |
| | <6>ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 |
| | <6>usb usb2: configuration #1 chosen from 1 choice |
| | <6>hub 2-0:1.0: USB hub found |
| | <6>hub 2-0:1.0: 2 ports detected |
| | <6>usbcore: registered new interface driver usblp |
| | <6>Initializing USB Mass Storage driver... |
| | <6>usbcore: registered new interface driver usb-storage |
| | <6>USB Mass Storage support registered. |
| | <6>usbcore: registered new interface driver usbserial |
| | <6>usbserial: USB Serial Driver core |
| | <6>USB Serial support registered for GSM modem (1-port) |
| | <6>usbcore: registered new interface driver option |
| | <6>option: v0.7.2:USB Driver for GSM modems |
| | <4>brcmboard: brcm_board_init entry |
| | <4>SES: Button Interrupt 0x1 is enabled |
| | <4>SES: LED GPIO 0x10 is enabled |
| | <4>PCIe: No device found - Powering down |
| | <6>Serial: BCM63XX driver $Revision: 3.00 $ |
| | <6>Magic SysRq enabled (type ^ h for list of supported commands) |
| | <6>ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX |
| | <6>ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX |
| | <4>bcmPktDma_init: Broadcom Packet DMA Library initialized |
| | <4>Total # RxBds=1448 |
| | <4>bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized |
| | <4> |
| | <4>bcmxtmrt: Broadcom BCM3168C0 ATM/PTM Network Device v0.4 Apr 9 2013 19:12:22 |
| | <4>GACT probability NOT on |
| | <4>Mirror/redirect action on |
| | <4>u32 classifier |
| | <4> input device check on |
| | <4> Actions configured |
| | <6>TCP cubic registered |
| | <6>Initializing XFRM netlink socket |
| | <6>NET: Registered protocol family 10 |
| | <6>IPv6 over IPv4 tunneling driver |
| | <6>NET: Registered protocol family 17 |
| | <6>NET: Registered protocol family 15 |
| | <6>Initializing MCPD Module |
| | <6>Ebtables v2.0 registered |
| | <6>ebt_time registered |
| | <6>ebt_ftos registered |
| | <6>ebt_wmm_mark registered |
| | <6>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> |
| | <6>All bugs added by David S. Miller <davem@redhat.com> |
| | <4>VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. |
| | <6>Freeing unused kernel memory: 152k freed |
| | <4>bcm_ingqos: module license 'Proprietary' taints kernel. |
| | <4>Disabling lock debugging due to kernel taint |
| | <4>Broadcom Ingress QoS Module Char Driver v0.1 Apr 9 2013 19:10:59 Registered<243> |
| | <4> |
| | <4>Broadcom Ingress QoS ver 0.1 initialized |
| | <4>BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066329B (9MB), num of buffers=4802, buf size=2096 |
| | <4>Broadcom BPM Module Char Driver v0.1 Apr 9 2013 19:10:49 Registered<244> |
| | <4>[NTC bpm] bpm_set_status: BPM status : enabled |
| | <4> |
| | <4>NBUFF v1.0 Initialized |
| | <4>Initialized fcache state |
| | <4>Broadcom Packet Flow Cache Char Driver v2.2 Apr 9 2013 19:10:59 Registered<242> |
| | <4>Created Proc FS /procfs/fcache |
| | <4>Broadcom Packet Flow Cache registered with netdev chain |
| | <4>Broadcom Packet Flow Cache learning via BLOG enabled. |
| | <4>Constructed Broadcom Packet Flow Cache v2.2 Apr 9 2013 19:10:59 |
| | <4>chipId 0x631680C0 |
| | <4>Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 9 2013 19:10:50 Registered <241> |
| | <4>FAP Debug values at 0x00000010 0x00000010 |
| | <4>Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 |
| | <4>FAP Soft Reset Done |
| | <4>4ke Reset Done |
| | <4>Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 |
| | <4>FAP Soft Reset Done |
| | <4>4ke Reset Done |
| | <4>Allocated FAP0 GSO Buffers (0xA2A56120) : 1048576 bytes @ 0xA2B00000 |
| | <4>Allocated FAP1 GSO Buffers (0xA2A76120) : 1048576 bytes @ 0xA2400000 |
| | <4>[NTC fapProto] fapReset : Reset FAP Protocol layer |
| | <4>fapDrv_construct: FAP0: pManagedMemory=b08209f0. wastage 8 bytes |
| | <4>[FAP0] DSPRAM : stack <0x80000000><1024>, global <0x80000400><6408>, free <760>, total<8192> |
| | <4>[FAP1] DSPRAM : stack <0x80000000><1024>, global <0x80000400><6408>, free <760>, total<8192> |
| | <4>[FAP0] PSM : addr<0x80002000>, used <18744>, free <5832>, total <24576> |
| | <4>[FAP1] PSM : addr<0x80002000>, used <18744>, free <5832>, total <24576> |
| | <4>fapDrv_construct: FAP1: pManagedMemory=b0a209f0. wastage 8 bytes |
| | <4>[FAP0] DQM : availableMemory 54968 bytes, nextByteAddress 0xE0006948 |
| | <4>[FAP1] DQM : availableMemory 54968 bytes, nextByteAddress 0xE0006948 |
| | <4>bcmPktDma_bind: FAP Driver binding successfull |
| | <4>[FAP0] GSO Buffer set to 0xA2B00000 |
| | <4>[FAP1] GSO Buffer set to 0xA2400000 |
| | <4>[FAP0] FAP BPM Initialized. |
| | <4>[FAP1] FAP BPM Initialized. |
| | <4>[FAP0] FAP Ingress QoS Initialized. |
| | <4>[FAP1] FAP Ingress QoS Initialized. |
| | <4>bcmxtmcfg: bcmxtmcfg_init entry |
| | <4>adsl: adsl_init entry |
| | <4>Broadcom BCM63168C0 Ethernet Network Device v0.1 Apr 9 2013 19:12:15 |
| | <4>fapDrv_psmAlloc: fapIdx=0, size: 3600, offset=b08209f0 bytes remaining 7400 |
| | <4>ETH Init: Ch:0 - 180 tx BDs at 0xb08209f0 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 97 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 109 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 117 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 120 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 122 |
| | <4>fapDrv_psmAlloc: fapIdx=1, size: 3600, offset=b0a209f0 bytes remaining 7400 |
| | <4>ETH Init: Ch:1 - 180 tx BDs at 0xb0a209f0 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 97 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 109 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 117 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 120 |
| | <4>bcmPktDma_EthInitTxChan_Dqm LINE 122 |
| | <4>fapDrv_psmAlloc: wastage 8 bytes |
| | <4>fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821800 bytes remaining 2584 |
| | <4>ETH Init: Ch:0 - 600 rx BDs at 0xb0821800 |
| | <4>fapDrv_psmAlloc: wastage 8 bytes |
| | <4>fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21800 bytes remaining 2584 |
| | <4>ETH Init: Ch:1 - 600 rx BDs at 0xb0a21800 |
| | <4>dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered |
| | <4>eth1: MAC Address: FC:F5:28:XX:XX:XX |
| | <4>eth2: MAC Address: FC:F5:28:XX:XX:XX |
| | <4>eth3: MAC Address: FC:F5:28:XX:XX:XX |
| | <4>eth0: MAC Address: FC:F5:28:XX:XX:XX |
| | <4>eth4: MAC Address: FC:F5:28:XX:XX:XX |
| | <2>eth3 Link UP 100 mbps full duplex |
| | <2>eth4 Link UP 1000 mbps full duplex |
| | <6>message received before monitor task is initialized kerSysSendtoMonitorTask |
| | <4>Broadcom BCM3168C0 USB Network Device v0.4a Apr 9 2013 19:11:06 |
| | <4>usb0: MAC Address: FC F5 28 XX XX XX |
| | <4>usb0: Host MAC Address: FC F5 28 XX XX XX |
| | <3>hub 1-0:1.0: over-current change on port 2 |
| | <4>USBD Initialization done status 0 |
| | <4>USB Link DOWN. |
| | <6>message received before monitor task is initialized kerSysSendtoMonitorTask |
| | <4>--SMP support |
| | <7>PCI: Setting latency timer of device 0000:00:00.0 to 64 |
| | <4>wl: passivemode=1 |
| | <4>wl: napimode=0 |
| | <4>wl: allocskbmode=1 |
| | <4>otp_read_pci: bad crc |
| | <4>Neither SPROM nor OTP has valid image |
| | <4>wl:srom/otp not programmed, using main memory mapped srom info(wombo board) |
| | <4>wl:loading /etc/wlan/bcm6362_map.bin |
| | <4>wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.3.cpe4.12L01.8 |
| | <4>dgasp: kerSysRegisterDyingGaspHandler: wl0 registered |
| | <4>p8021ag: p8021ag_init entry |
| | <6>Broadcom 802.1Q VLAN Interface, v0.1</nowiki> |
| | </WRAP>\\ |
| | |
| | |
| | ===== Notes ===== |
| | |
| | ==== CFE-Bootloader ==== |
| | |
| | CFE-Bootloader has Web-ui for flash-recovery (http://192.168.1.1), just stop autoboot |
| | |
| | <WRAP bootlog> |
| | <nowiki> |
| | CFE version 1.0.38-112.12 for BCM963268 (32bit,SP,BE) |
| | Build Date: 05/21/2012 (zongyue@MsgSW4-SerVer) |
| | Copyright (C) 2000-2011 Broadcom Corporation. |
| | |
| | NAND flash device: name Samsung K9F1G08U0D, id 0xecf1 block 128KB size 131072KB |
| | Chip ID: BCM63168C0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz |
| | Main Thread: TP0 |
| | Memory Test Passed |
| | Total Memory: 67108864 bytes (64MB) |
| | Boot Address: 0xb8000000 |
| | |
| | Checking Reset button on EXT INTR 0 |
| | Board IP address : 192.168.1.1:ffffff00 |
| | Host IP address : 192.168.1.100 |
| | Gateway IP address : |
| | Run from flash/host (f/h) : f |
| | Default host run file name : vmlinux |
| | Default host flash file name : bcm963xx_fs_kernel |
| | Boot delay (0-9 seconds) : 1 |
| | Boot image (0=latest, 1=previous) : 0 |
| | Board Id (0-6) : 963168VX |
| | Number of MAC Addresses (1-32) : 12 |
| | Base MAC Address : b0:b2:dc:f2:56:6c |
| | PSI Size (1-128) KBytes : 64 |
| | Enable Backup PSI [0|1] : 0 |
| | System Log Size (0-256) KBytes : 0 |
| | Main Thread Number [0|1] : 0 |
| | |
| | *** Press any key to stop auto run (1 seconds) *** |
| | Auto run second count down: 1 |
| | web info: Waiting for connection on socket 0.␛[J |
| | CFE> athe |
| | Available commands: |
| | |
| | ATSE show the seed of password generator |
| | ATEN set BootExtension Debug Flag |
| | ATCR Clear console screen |
| | ATSH dump manufacturer related data in ROM |
| | ATUR xmodem upload router firmware to flash ROM |
| | ATIR Set ImageDefault to ROM-D partition |
| | ATER Erase ROM-D partition |
| | ATBL Print boot line and board parameter info |
| | ATDU Dump memory or registers. |
| | ATBR Reset to default Romfile |
| | ATGO boot router |
| | ATSR system reboot |
| | ATMB Use for multiboot. |
| | ATHE print help |
| | |
| | For more information about a command, enter 'help command-name' |
| | *** command status = 0 |
| | CFE> |
| | CFE> atbl |
| | Board IP address : 192.168.1.1:ffffff00 |
| | Host IP address : 192.168.1.100 |
| | Gateway IP address : |
| | Run from flash/host (f/h) : f |
| | Default host run file name : vmlinux |
| | Default host flash file name : bcm963xx_fs_kernel |
| | Boot delay (0-9 seconds) : 1 |
| | Boot image (0=latest, 1=previous) : 0 |
| | Board Id (0-6) : 963168VX |
| | Number of MAC Addresses (1-32) : 12 |
| | Base MAC Address : b0:b2:dc:f2:56:6c |
| | PSI Size (1-128) KBytes : 64 |
| | Enable Backup PSI [0|1] : 0 |
| | System Log Size (0-256) KBytes : 0 |
| | Main Thread Number [0|1] : 0 |
| | |
| | *** command status = 0 |
| | CFE> |
| | web info: Waiting for connection on socket 1.␛[J |
| | web warning: Unexpected TCP disconnect.␛[J |
| | web warning: Unexpected TCP disconnect.␛[J |
| | web info: Waiting for connection on socket 0.␛[J |
| | web info: Waiting for connection on socket 1.␛[J |
| | web warning: Unexpected TCP disconnect.␛[J |
| | web info: Waiting for connection on socket 0.␛[J |
| | web info: Waiting for connection on socket 1.␛[J |
| | CFE> atsh |
| | |
| | FW Version : V1.00(AAEB.5) |
| | Bootbase Version : V1.52 | 05/21/2012 12:24:58 |
| | Vendor Name : ZyXEL Technology Corp. |
| | Product Model : VMG1312-B30A |
| | Serial Number : S120Y3305xxxx |
| | First MAC Address : B0B2DCF256xx |
| | Last MAC Address : B0B2DCF256xx |
| | MAC Address Quantity : 12 |
| | Default Country Code : ED |
| | Boot Module Debug Flag : 00 |
| | RootFS Checksum : 07ea8753 |
| | ImageDefaultChecksum : 229f5a77 |
| | Main Feature Bits : 00 |
| | Other Feature Bits : |
| | 4d 53 40 13 00 00 00 00-00 00 00 00 00 00 00 00 |
| | 00 00 00 00 00 00 00 00-00 00 00 00 00 00 |
| | |
| | *** command status = 0 |
| | </nowiki> |
| | </WRAP>\\ |
| | |
| | ===== Tags ===== |
| | [[meta:tags|How to add tags]] |
| | {{tag>bcm63168 FastEthernet 1NIC 1WNIC 5Port USB 2USB ath9k DetachableAntenna 64RAM 8Flash MIPS MIPS32 34K vDSL2+ 12v_powered unsupported}} |