ZyXEL P-870HNU-51c (Q1000Z)

OEM source code - q1000z_source.zip

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
P870HNU-51c -- -- Trunk Working with limited driver support

NOT SUPPORTED YET

SoC Ram Flash Network USB Serial JTag
Broadcom 6368 64 MiB 32 MiB 4 Yes Yes ?

Manufacturer's site: http://www.zyxel.com/us/en/homepage.shtml

Forum: https://forum.openwrt.org/viewtopic.php?id=56921

# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 004d0000 004d0000 "Physically mapped flash"
# mount
/dev/mtdblock0 on / type squashfs (ro)
/proc on /proc type proc (rw)
tmpfs on /var type tmpfs (rw)
tmpfs on /mnt type tmpfs (rw)
tmpfs on /tmp/http_session type tmpfs (rw)
sysfs on /sys type sysfs (rw)
# df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/mtdblock0            4928      4928         0 100% /
#
Instruction set MIPS
Vendor Broadcom
bootloader cfe
Board ID 96368MVWG (wrong layout)
System-On-Chip Broadcom BCM6368UKPBG
CPU @Frq BMIPS4350 V3.1 @400 MHz BMIPS Dual Core
Flash size 32 MiB
Flash Chip MX29GL256E-90Q
RAM size 64 MiB
RAM Chip 2x Winbound W9425G6JH-5
Wireless BCM43222KFBG (onboard)
switch Broadcom BCM53115, 4x Gigabit Ethernet
Modem vDSL2
USB Yes 1x 2.0
Serial Yes
JTAG Maybe

Model Number Q1000z

Note: This will void your warranty!

  • To remove the cover remove 4 screws from underside of device

Main PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

CFE> CFE> ATSH <---- Dump Manufacturer Info ZLD Version : V1.00(BKV.0)b15_0103 Bootbase Version : V1.13 | 08/17/2010 17:28:37 Vendor Name : ZyXEL Communications Corp. Product Model : P-870HNU-51c Serial No. : S110Y47013552 First MAC Address : 086C876FB08C Last MAC Address : 086C876FB08F MAC Address Quantity : 04 Default Country Code : 01 Boot Module Debug Flag : 01 RootFS Checksum : 45e493fe Kernel Checksum : cd19cfae RomFile Checksum : 02239061 Main Feature Bits : 00 Other Feature Bits : 5a 59 40 01 00 00 00 53-31 31 30 59 34 37 30 31 33 35 35 32 00 00 00 00-00 03 41 13 00 00 *** command status = 0 CFE> CFE> ATSE P-870HNU-51c <---- Generate Random Seed Number for Product Model 00023E000000 OK *** command status = 0 Enter seed number (00023E000000) in ZynPass or here: http://www.tonycool.es/zyxel/zynpass_en.htm to generate password CFE> CFE> ATEN 1, 10F0A59F <---- Unlock the Device with password OK *** command status = 0 CFE> ATHE <---- List the, now extended, Command Set Available commands: ATMC Bootup device with SMT rom file ATSW Show WPAPSK or change WPAPSK ATMT reduce manufacture bootup time for wireless calibration ATHV write Hardware Version to flash ROM ATSN write Series Number to flash ROM ATPA set wireless power index ATWZ write MAC addr, Country code, EngDbgFlag, FeatureBit, MAC Number to flash ROM ATSE show the seed of password generator ATEN set BootExtension Debug Flag ATCR Clear console screen ATBT block0 write enable ATTE Restore to TE configuration ATRD xmodem upload ROM-D ATLC xmodem upload defaultcfg ATSH dump manufacturer related data in ROM ATUB xmodem upload bootloader ATUR xmodem upload router firmware to flash ROM ATUW xmodem upload flash image to flash ROM ATIR Set ImageDefault to ROM-D partition ATER Erase ROM-D partition ATBL Print boot line and board parameter info ATAF Change board AFE ID ATBP Change board parameters ATIP Change booline parameters ATDU Dump memory or registers. ATWW Set memory or registers. ATBR Reset to default Romfile ATGO boot router ATSR system reboot ATTB Write the cfe image into flash ATTR upload router firmware to flash ROM from TFTP Client ATTW Write the whole image start from beginning of the flash ATNR Reinitialize NAND flash ATRM Dump flash data ledhon Turn on the specific LED with high ledhof Turn off the specific LED with high ledlon Turn on the specific LED with low ledlof Turn off the specific LED with low ledh Blink all LEDs with pulling high ledl Blink all LEDs with pulling low ATMB Use for multiboot. ATRT Test memory. ATHE print help For more information about a command, enter 'help command-name' *** command status = 0 CFE> CFE> ATBT 1 <---- Enable write


CFE version 1.13.0-104.4 for BCM96368 (32bit,SP,BE) Build Date: 08/17/2010 (kuanjung@MSGSW4-server2) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name S29GL256P90, id 0x2222 size 32768KB Total Flash size: 32768K with 256 sectors ethsw: found bcm53115! Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.0.2:ffffff00 Host IP address : 192.168.0.100 Gateway IP address : 192.168.0.1 Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 5 Boot image (0=latest, 1=previous) : 0 Board Id (0-11) : 96368MVWG Number of MAC Addresses (1-32) : 4 Base MAC Address : 08:6c:87:6f:b0:8c PSI Size (1-128 KBytes : 128 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (5 seconds) *** Auto run second count down: 5 web info: Waiting for connection on socket 0. CFE> ATTR 192.168.0.100:QZZ001-4.4.015.1-Q1000Z.bin Loading 192.168.0.100:QZZ001-4.4.015.1-Q1000Z.bin ... Finished loading 5906711 bytes Flashing root file system and kernel at 0xb8020000: .............................................. . *** Image flash done *** ! Resetting board...▒ CFE version 1.13.0-104.4 for BCM96368 (32bit,SP,BE) Build Date: 08/17/2010 (kuanjung@MSGSW4-server2) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name S29GL256P90, id 0x2222 size 32768KB Total Flash size: 32768K with 256 sectors ethsw: found bcm53115! Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.0.2:ffffff00 Host IP address : 192.168.0.100 Gateway IP address : 192.168.0.1 Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 5 Boot image (0=latest, 1=previous) : 0 Board Id (0-11) : 96368MVWG Number of MAC Addresses (1-32) : 4 Base MAC Address : 08:6c:87:6f:b0:8c PSI Size (1-128 KBytes : 128 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (5 seconds) *** Auto run second count down: 0 Checking Reset button on GPIO 34 Wait for Multiboot Service Packet... 0 flash_addr_kernel b84f0100 Booting from latest image (0xb8020000) ... Code Address: 0x80020000, Entry Address: 0x8026a000 Decompression OK! Entry at 0x8026a000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 38 buffers found. Closing DMA Channels. Starting program at 0x8026a000 Linux version 2.6.21.5 (kuanjung@MSGSW4-server2) (gcc version 4.2.3) #1 Mon Jan 3 11:52:30 CST 2011 Parallel flash device: name S29GL256P90, id 0x2222 size 32768KB 96368MVWG prom init CPU revision is: 0002a031 Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) On node 0 totalpages: 16128 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 brcm mips: enabling icache and dcache... Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, linesize 16 bytes. Synthesized TLB refill handler (21 instructions). Synthesized TLB load handler fastpath (33 instructions). Synthesized TLB store handler fastpath (33 instructions). Synthesized TLB modify handler fastpath (32 instructions). PID hash table entries: 256 (order: 8, 1024 bytes) Using 200.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61164k/64512k available (1818k kernel code, 3332k reserved, 521k data, 88k init, 0k highmem) KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000> Calibrating delay loop... 398.33 BogoMIPS (lpj=199168) Mount-cache hash table entries: 512 wait instruction: enabled NET: Registered protocol family 16 Total Flash size: 32768K with 256 sectors registering PCI controller with io_map_base unset usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb BLOG v2.1 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) PPP generic driver version 2.4.2 NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8020100 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver brcmboard: brcm_board_init entry kerSysScreenPciDevices: 0x14e4:0xa8d6:(slot 1) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0xd is enabled Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Jan 3 2011 11:51:25 Broadcom Logger v0.1 Jan 3 2011 11:50:46 IPSEC SPU: SUCCEEDED Mirror/redirect action on u32 classifier input device check on Actions configured Ah4 module with HW offload TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 88k freed init started: BusyBox v1.00 (2011.01.03-04:20+0000) multi-call binary BusyBox v1.00 (2011.01.03-04:20+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Broadcom Packet Flow Cache Char Driver v2.1 Mar 10 2010 16:00:27 Registered<242> NBUFF v1.0 Initialized Broadcom Packet Flow Cache learning via BLOG enabled. Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Constructed Broadcom Packet Flow Cache v2.1 Mar 10 2010 16:00:26 Broadcom Packet CMF (Experimental) Char Driver v0.1 Mar 10 2010 16:00:25 Registered<232> Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Mar 10 2010 16:00:24 Loaded bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6368B2 Ethernet Network Device v0.1 Jan 3 2011 11:50:50 KLOB extended to 2 pools KLOB extended to 3 pools KLOB extended to 4 pools KLOB extended to 5 pools KLOB extended to 6 pools KLOB extended to 7 pools KLOB extended to 8 pools Config Switch Through SPI Slave Select 0 ethsw: found bcm53115! dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Broadcom Packet CMF (Experimental) SWC RESET. Broadcom Packet CMF (Experimental) SWC INITIALIZED. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Mar 10 2010 16:00:25 Registered Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Mar 10 2010 16:00:25 Registered Broadcom Packet CMF (Experimental) ENABLED. eth3: MAC Address: 08:6C:87:6F:B0:8C eth2: MAC Address: 08:6C:87:6F:B0:8C eth1: MAC Address: 08:6C:87:6F:B0:8C eth0: MAC Address: 08:6C:87:6F:B0:8C eth3 Link DOWN. eth2 Link DOWN. eth1 Link DOWN. eth0 Link DOWN. PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: MAC addr from system pool. id:0x776c0000 wl0: MAC Address: 08:6C:87:6F:B0:8D wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.10.144.6.cpe4.404.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered p8021ag: p8021ag_init entry ===== Release Version 4.04L.01 (build timestamp 110103_1403) ===== eth1 Link UP 1000 mbps full duplex ===========Insert IP modules=========== ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (4096 buckets, 8192 max) ip_queue: DYNAHELPER change default policy for input chain add exception for TR069 connection request port device eth0 entered promiscuous mode device eth1 entered promiscuous mode br0: port 2(eth1) entering learning state br0: topology change detected, propagating br0: port 2(eth1) entering forwarding state device eth2 entered promiscuous mode device eth3 entered promiscuous mode WLmngr Daemon is running optarg=0 shmId=0 device wl0 entered promiscuous mode wlevt_init@109: opened loopback socket 4 wlevt is ready for new msg... br0: port 5(wl0) entering learning state br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state BcmAdsl_Initialize=0xC00A4A38, g_pFnNotifyCallback=0xC00CF994 Clocks for QPROC and AFE are being aligned with step through ... AFE is aligned, i = 054, PhaseValue = -050, PhaseCntl = 0x3FCA0000 QPROC is aligned, i = 027, PhaseValue = 0050, PhaseCntl = 0x3FCA401B Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x78 AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f pSdramPHY=0xA3FFFFF8, 0x55555555 0x55555775 *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xBF368 => 0xECA50 *** AdslCoreSharedMemInit: shareMemAvailable=79248 AdslCoreHwReset: pLocSbSta=83248000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FB4E08 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) /var/cert/acscert2.cacert: cannot open ln: /var/cert/7651b327.0: File exists wlctl -i wl0 phytype > /var/wl0 wlctl -i wl0 revinfo > /var/wl0 wlctl -i wl0 bands > /var/wl0bands wlctl -i wl0 ver > /var/wlver wlctl -i wl0 cap > /var/wl0cap General UPnP daemon is ready to run with NATT 1 device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering learning state br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state WPS Device PIN = 37592356 wlctl -i wl0 phy_watchdog 0 wlctl -i wl0 wds none wlctl -i wl0 up wlctl -i wl0 down wlctl -i wl0 mbss 0 wlctl -i wl0 bss -C 0 down wlctl -i wl0 bss -C 1 down wlctl -i wl0 bss -C 2 down wlctl -i wl0 bss -C 3 down wlctl -i wl0 ssid -C 0 'm''y''q''w''e''s''t''3''5''5''2' Setting SSID "myqwest3552" wlctl -i wl0 ssid -C 1 'S''S''I''D''2' Setting SSID "SSID2" wlctl -i wl0 ssid -C 2 'S''S''I''D''3' Setting SSID "SSID3" wlctl -i wl0 ssid -C 3 'S''S''I''D''4' Setting SSID "SSID4" wlctl -i wl0 cur_etheraddr 08:6C:87:6F:B0:8D 2>/dev/null wlctl -i wl0.1 cur_etheraddr 5a:6c:87:6f:b0:8e 2>/dev/null wlctl -i wl0.2 cur_etheraddr 5a:6c:87:6f:b0:8f 2>/dev/null wlctl -i wl0.3 cur_etheraddr 5a:6c:87:6f:b0:8c 2>/dev/null wlctl -i wl0 ap 1 wlctl -i wl0 infra 1 wlctl -i wl0 closed 0 wlctl -i wl0 country US wlctl -i wl0 band b wlctl -i wl0 regulatory 0 wlctl -i wl0 radar 0 2>/dev/null wlctl -i wl0 spect 0 2>/dev/null wlctl -i wl0 nmode -1 wlctl -i wl0 mimo_bw_cap 0 wlctl -i wl0 wpa_cap -C 0 > /var/wpa_cap0 wlctl -i wl0 wpa_cap -C 0 0 2>/dev/null wlctl -i wl0 wpa_cap -C 1 > /var/wpa_cap0 wlctl -i wl0 wpa_cap -C 1 0 2>/dev/null wlctl -i wl0 wpa_cap -C 2 > /var/wpa_cap0 wlctl -i wl0 wpa_cap -C 2 0 2>/dev/null wlctl -i wl0 wpa_cap -C 3 > /var/wpa_cap0 backup_psi_number_blk=0 result=131072 wlctl -i wl0 wpa_cap -C 3 0 2>/dev/null wlctl -i wl0 maxassoc 64 wlctl -i wl0 bss_maxassoc 16 wlctl -i wl0 gmode Auto wlctl -i wl0 gmode_protection_override -1 wlctl -i wl0 gmode_protection_control 2 wlctl -i wl0 nmode_protection_override -1 wlctl -i wl0 protection_control 2 wlctl -i wl0 rifs_advert 0 wlctl -i wl0 obss_coex 0 wlctl -i wl0 rxchain_pwrsave_enable 0 wlctl -i wl0 rxchain_pwrsave_quiet_time 10 wlctl -i wl0 rxchain_pwrsave_pps 10 wlctl -i wl0 radio_pwrsave_enable 0 wlctl -i wl0 radio_pwrsave_quiet_time 10 wlctl -i wl0 radio_pwrsave_pps 10 wlctl -i wl0 radio_pwrsave_on_time 50 wlctl -i wl0 stbc_tx -1 wlctl -i wl0 nreqd 0 wlctl -i wl0 txchain 3 wlctl -i wl0 rxchain 3 wlctl -i wl0 wme 0 2>/dev/null wlctl -i wl0 afterburner_override 0 2>/dev/null wlctl -i wl0 ampdu 1 wlctl -i wl0 amsdu 0 wlctl -i wl0 afterburner_override 0 wlctl -i wl0 wme 1 2>/dev/null wlctl -i wl0 wme_noack 0 2>/dev/null wlctl -i wl0 wme_apsd 0 2>/dev/null wlctl -i wl0 wme_bss_disable 0 wlctl -i wl0 wme_ac ap be aifsn 3 2>/dev/null wlctl -i wl0 wme_ac ap be ecwmin 4 2>/dev/null wlctl -i wl0 wme_ac ap be ecwmax 6 2>/dev/null wlctl -i wl0 wme_ac ap be txop 0 2>/dev/null wlctl -i wl0 wme_ac ap bk aifsn 7 2>/dev/null wlctl -i wl0 wme_ac ap bk ecwmin 4 2>/dev/null wlctl -i wl0 wme_ac ap bk ecwmax 10 2>/dev/null wlctl -i wl0 wme_ac ap bk txop 0 2>/dev/null wlctl -i wl0 wme_ac ap vi aifsn 1 2>/dev/null wlctl -i wl0 wme_ac ap vi ecwmin 3 2>/dev/null wlctl -i wl0 wme_ac ap vi ecwmax 4 2>/dev/null wlctl -i wl0 wme_ac ap vi txop 94 2>/dev/null wlctl -i wl0 wme_ac ap vobr0: port 5(wl0) entering learning state aifsn 1 2>/dev/br0: topology change detected, propagating null wlctl -i wbr0: port 5(wl0) entering forwarding state l0 wme_ac ap vo ecwmin 2 2>/dev/null wlctl -i wl0 wme_ac ap vo ecwmax 3 2>/dev/null wlctl -i wl0 wme_ac ap vo txop 47 2>/dev/null wlctl -i wl0 wme_ac sta be aifsn 3 2>/dev/null wlctl -i wl0 wme_ac sta be ecwmin 4 2>/dev/null wlctl -i wl0 wme_ac sta be ecwmax 10 2>/dev/null wlctl -i wl0 wme_ac sta be txop 0 2>/dev/null wlctl -i wl0 wme_ac sta bk aifsn 7 2>/dev/null wlctl -i wl0 wme_ac sta bk ecwmin 4 2>/dev/null wlctl -i wl0 wme_ac sta bk ecwmax 10 2>/dev/null wlctl -i wl0 wme_ac sta bk txop 0 2>/dev/null wlctl -i wl0 wme_ac sta vi aifsn 2 2>/dev/null wlctl -i wl0 wme_ac sta vi ecwmin 3 2>/dev/null wlctl -i wl0 wme_ac sta vi ecwmax 4 2>/dev/null wlctl -i wl0 wme_ac sta vi txop 94 2>/dev/null wlctl -i wl0 wme_ac sta vo aifsn 2 2>/dev/null wlctl -i wl0 wme_ac sta vo ecwmin 2 2>/dev/null wlctl -i wl0 wme_ac sta vo ecwmax 3 2>/dev/null wlctl -i wl0 wme_ac sta vo txop 47 2>/dev/null wlctl -i wl0 rate 0 wlctl -i wl0 bg_rate 0 wlctl -i wl0 leddc 0 2>/dev/null wlctl -i wl0 bg_mrate 18.0 wlctl -i wl0 rateset default wlctl -i wl0 rtsthresh 2347 wlctl -i wl0 fragthresh 2346 wlctl -i wl0 dtim 1 wlctl -i wl0 bi 100 wlctl -i wl0 frameburst 1 wlctl -i wl0 ap_isolate 0 wlctl -i wl0 pwr_percent 100 wlctl -i wl0 wmf_bss_enable 0 wlctl -i wl0.1 wmf_bss_enable 0 wlctl -i wl0.2 wmf_bss_enable 0 wlctl -i wl0.3 wmf_bss_enable 0 wlctl -i wl0 chanim_enab 1 wlctl -i wl0 enable_tx_delay 0 wlctl -i wl0 enadevice wl0 left promiscuous mode ble_rx_delay 0 br0: port 5(wl0) entering disabled state wlctl -i wl0 enable_percal_delay 1 wlctl -i wl0 mac none wlctl -i wl0 macmode 0 wlctl -i wl0 up wlctl -i wl0 autochannel 1 chanspec 0x2b0b selected wlctl -i wl0 autochannel 2 wlctl -i wl0 csscantimer 0 wlctl -i wl0 chanspec > /var/curchaspec0 wlctl -i wl0 chanspec > /var/curchaspec0 wlctl -i wl0 autochannel 4 > /var/wl0sch device wl0 entered promiscuous mode br0: port 5(wl0) entering learning state br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state Reaped 830 UPnP daemon is ready to run wlctl -i wl0 rmwep -C 0 0 wlctl -i wl0 rmwep -C 0 1 wlctl -i wl0 rmwep -C 0 2 wlctl -i wl0 rmwep -C 0 3 wlctl -i wl0 rmwep -C 1 0 wlctl -i wl0 rmwep -C 1 1 wlctl -i wl0 rmwep -C 1 2 wlctl -i wl0 rmwep -C 1 3 wlctl -i wl0 rmwep -C 2 0 wlctl -i wl0 rmwep -C 2 1 wlctl -i wl0 rmwep -C 2 2 wlctl -i wl0 rmwep -C 2 3 wlctl -i wl0 rmwep -C 3 0 wlctl -i wl0 rmwep -C 3 1 wlctl -i wl0 rmwep -C 3 2 wlctl -i wl0 rmwep -C 3 3 wlctl -i wl0 wsec -C 0 6 wlctl -i wl0 wsec_restrict -C 0 1 wlctl -i wl0 wpa_auth -C 0 132 wlctl -i wl0 eap 1 wlctl -i wl0 auth -C 0 0 wlctl -i wl0 wdswsec 0 wlctl -i wl0 wdswsec_enable 0 wlctl -i wl0 bss -C 0 up wlctl -i wl0 lazywds 0 wlctl -i wl0 wds wlctl -i wl0 phy_watchdog 1 wlctl -i wl0 fcache 1 wlctl -i wl0 chanspec > /var/curchaspec0 wlctl -i wl0 chanspec > /var/curchaspec0 wlctl -i wl0 chanspec > /var/curchaspec0 wlctl -i wl0 chanspec > /var/curchaspec0 wlctl -i wl0 autho_sta_list > /var/wps_wl0 wlctl -i wl0 authe_sta_list > /var/wl0_authe wlctl -i wl0 assoclist > /var/wl0_assoc wlctl -i wl0 autho_sta_list > /var/wl0_autho Qwest xDSL Router Login:


flash_addr_kernel b8020100 Booting from only image (0xb8020000) ... Code Address: 0x80A00000, Entry Address: 0x80a00000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80a00000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80a00000 [ 0.000000] Linux version 3.18.14 (jeff@jeff-Virtual-Machine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45715) ) #3 Sat May 23 14:16:55 CDT 2015 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.13.0-104.4 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board: board name: P870HNU_51c [ 0.000000] MIPS: machine is ZyXEL P870HNU-51c [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 59964K/65536K available (2657K kernel code, 131K rwdata, 560K rodata, 1316K init, 192K bss, 5572K reserved) [ 0.000000] NR_IRQS:256 [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.052000] NET: Registered protocol family 16 [ 0.060000] registering PCI controller with io_map_base unset [ 0.068000] PCI host bridge to bus 0000:00 [ 0.072000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.076000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.080000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.088000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.092000] Switched to clocksource MIPS [ 0.096000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.124000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.168000] ssb: WARNING: Using fallback SPROM failed (err -2) [ 0.172000] ssb: WARNING: Invalid SPROM CRC (corrupt SPROM) [ 0.180000] ssb: Unsupported SPROM revision 255 detected. Will extract v1 [ 0.208000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.216000] NET: Registered protocol family 2 [ 0.224000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.228000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.236000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.244000] TCP: reno registered [ 0.248000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.252000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] NET: Registered protocol family 1 [ 0.264000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.272000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.280000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.288000] msgmni has been set to 117 [ 0.296000] io scheduler noop registered [ 0.300000] io scheduler deadline registered (default) [ 0.316000] console [ttyS0] enabled MMIO 0xb0000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart [ 0.316000] console [ttyS0] enabled [ 0.320000] bootconsole [early0] disabled [ 0.320000] bootconsole [early0] disabled [ 0.332000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.336000] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.348000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.352000] Amd/Fujitsu Extended Query version 1.3. [ 0.360000] number of CFI chips: 1 [ 0.364000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368MVGW [ 0.372000] 6 bcm63xxpart partitions found on MTD device 18000000.nor [ 0.376000] Creating 6 MTD partitions on "18000000.nor": [ 0.384000] 0x000000000000-0x000000020000 : "CFE" [ 0.388000] 0x000000020100-0x0000001435a6 : "kernel" [ 0.396000] 0x0000001435a6-0x000001e40000 : "rootfs" [ 0.400000] mtd: device 2 (rootfs) set to be root filesystem [ 0.408000] 1 squashfs-split partitions found on MTD device rootfs [ 0.412000] 0x000000500000-0x000001e40000 : "rootfs_data" [ 0.420000] 0x000000020000-0x000001e40000 : "linux" [ 0.428000] 0x000001e40000-0x000001fe0000 : "board_data" [ 0.432000] 0x000001fe0000-0x000002000000 : "nvram" [ 0.440000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.464000] b53_common: found switch: BCM53115, rev 8 [ 0.500000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.512000] TCP: cubic registered [ 0.516000] NET: Registered protocol family 17 [ 0.520000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.532000] 8021q: 802.1Q VLAN Support v1.8 [ 0.548000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.572000] Freeing unused kernel memory: 1316K (80357000 - 804a0000) [ 2.080000] init: failed to symlink /tmp -> /var [ 2.084000] init: Console is alive [ 2.088000] init: - watchdog - [ 4.924000] usbcore: registered new interface driver usbfs [ 4.932000] usbcore: registered new interface driver hub [ 4.936000] usbcore: registered new device driver usb [ 4.952000] exFAT: Version 1.2.9 [ 4.976000] SCSI subsystem initialized [ 4.988000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.000000] ehci-platform: EHCI generic platform driver [ 5.108000] ehci-platform ehci-platform: EHCI Host Controller [ 5.112000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.120000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500 [ 5.140000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 5.148000] hub 1-0:1.0: USB hub found [ 5.152000] hub 1-0:1.0: 1 port detected [ 5.160000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.168000] ohci-platform: OHCI generic platform driver [ 5.176000] ohci-platform ohci-platform: Generic Platform OHCI controller [ 5.184000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 5.192000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600 [ 5.256000] hub 2-0:1.0: USB hub found [ 5.260000] hub 2-0:1.0: 1 port detected [ 5.272000] usbcore: registered new interface driver usb-storage [ 6.168000] init: - preinit - [ 7.156000] random: mktemp urandom read with 28 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.428000] mount_root: loading kmods from internal overlay [ 10.760000] jffs2: notice: (257) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found. [ 10.776000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 10.784000] block: extroot: not configured [ 10.840000] jffs2: notice: (254) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found. [ 10.964000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 10.976000] block: extroot: not configured [ 10.980000] mount_root: switching to jffs2 overlay ifconfig: SIOCGIFFLAGS: No such device [ 11.016000] procd: - early - [ 11.020000] procd: - watchdog - [ 11.984000] procd: - ubus - [ 12.992000] procd: - init - Please press Enter to activate this console. [ 16.252000] NET: Registered protocol family 10 [ 16.656000] wl: module license 'unspecified' taints kernel. [ 16.660000] Disabling lock debugging due to kernel taint [ 16.740000] SSB/BCMA glue driver successfully attached [ 16.772000] fallback_sprom: pci bus/device num mismatch: expected 0/0, but got 0/1 [ 16.780000] BCMA8D6(00:01) using sprom version 0 [ 16.792000] wl0: 5.10.56.27 driver failed with code 15 [ 16.812000] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: dm-devel@redhat.com [ 16.876000] ntfs: driver 2.1.31 [Flags: R/O MODULE]. [ 16.904000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.928000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 16.936000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 16.948000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.972000] nf_conntrack version 0.5.0 (957 buckets, 3828 max) [ 17.012000] usbcore: registered new interface driver ums-alauda [ 17.020000] usbcore: registered new interface driver ums-cypress [ 17.028000] usbcore: registered new interface driver ums-datafab [ 17.040000] usbcore: registered new interface driver ums-freecom [ 17.048000] usbcore: registered new interface driver ums-isd200 [ 17.056000] usbcore: registered new interface driver ums-jumpshot [ 17.068000] usbcore: registered new interface driver ums-karma [ 17.076000] usbcore: registered new interface driver ums-sddr09 [ 17.088000] usbcore: registered new interface driver ums-sddr55 [ 17.096000] usbcore: registered new interface driver ums-usbat [ 17.128000] xt_time: kernel timezone is -0000 [ 17.180000] cfg80211: Calling CRDA to update world regulatory domain [ 17.244000] cfg80211: World regulatory domain updated: [ 17.248000] cfg80211: DFS Master region: unset [ 17.252000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 17.264000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.272000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.280000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 17.288000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 17.296000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 17.304000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 17.312000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 17.320000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 17.400000] PPP generic driver version 2.4.2 [ 17.408000] NET: Registered protocol family 24 [ 17.456000] Broadcom 43xx driver loaded [ Features: PNL ] [ 27.960000] device eth0 entered promiscuous mode [ 27.984000] br-lan: port 1(eth0) entered forwarding state [ 27.988000] br-lan: port 1(eth0) entered forwarding state [ 29.992000] br-lan: port 1(eth0) entered forwarding state [ 31.816000] random: nonblocking pool is initialized BusyBox v1.23.2 (2015-05-23 02:56:14 CDT) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Bleeding Edge, r45715) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:/#


flash_addr_kernel b8020100 Booting from only image (0xb8020000) ... Code Address: 0x80A00000, Entry Address: 0x80a00000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80a00000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 151 buffers found. Closing DMA Channels. Starting program at 0x80a00000 [ 0.000000] Linux version 3.18.14 (jeff@jeff-Virtual-Machine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45741) ) #1 SMP Sat May 23 19:01:03 CDT 2015 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.13.0-104.4 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board: board name: P870HNU_51c [ 0.000000] MIPS: machine is ZyXEL P870HNU-51c [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] PERCPU: Embedded 9 pages/cpu @81087000 s5456 r8192 d23216 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 59724K/65536K available (2865K kernel code, 136K rwdata, 576K rodata, 1280K init, 197K bss, 5812K reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.052000] SMP: Booting CPU1... [ 0.056000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.056000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.056000] CPU1 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.096000] Synchronize counters for CPU 1: done. [ 0.100000] SMP: CPU1 is running [ 0.100000] Brought up 2 CPUs [ 0.116000] NET: Registered protocol family 16 [ 0.128000] registering PCI controller with io_map_base unset [ 0.152000] PCI host bridge to bus 0000:00 [ 0.156000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.160000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.168000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.184000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.196000] Switched to clocksource MIPS [ 0.196000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.236000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.280000] ssb: WARNING: Using fallback SPROM failed (err -2) [ 0.284000] ssb: WARNING: Invalid SPROM CRC (corrupt SPROM) [ 0.292000] ssb: Unsupported SPROM revision 255 detected. Will extract v1 [ 0.320000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.328000] NET: Registered protocol family 2 [ 0.336000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.344000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.348000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.356000] TCP: reno registered [ 0.360000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.364000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.372000] NET: Registered protocol family 1 [ 0.380000] futex hash table entries: 512 (order: 1, 8192 bytes) [ 0.388000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.392000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.404000] msgmni has been set to 116 [ 0.408000] io scheduler noop registered [ 0.412000] io scheduler deadline registered (default) [ 0.428000] console [ttyS0] enabled MMIO 0xb0000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart [ 0.428000] console [ttyS0] enabled [ 0.436000] bootconsole [early0] disabled [ 0.436000] bootconsole [early0] disabled [ 0.448000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.456000] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.464000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.472000] Amd/Fujitsu Extended Query version 1.3. [ 0.476000] number of CFI chips: 1 [ 0.480000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368MVGW [ 0.488000] 6 bcm63xxpart partitions found on MTD device 18000000.nor [ 0.492000] Creating 6 MTD partitions on "18000000.nor": [ 0.500000] 0x000000000000-0x000000020000 : "CFE" [ 0.504000] 0x000000020100-0x000000154823 : "kernel" [ 0.512000] 0x000000154823-0x000001e40000 : "rootfs" [ 0.520000] mtd: device 2 (rootfs) set to be root filesystem [ 0.524000] 1 squashfs-split partitions found on MTD device rootfs [ 0.532000] 0x0000004e0000-0x000001e40000 : "rootfs_data" [ 0.540000] 0x000000020000-0x000001e40000 : "linux" [ 0.544000] 0x000001e40000-0x000001fe0000 : "board_data" [ 0.552000] 0x000001fe0000-0x000002000000 : "nvram" [ 0.560000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.580000] b53_common: found switch: BCM53115, rev 8 [ 0.620000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.632000] TCP: cubic registered [ 0.636000] NET: Registered protocol family 17 [ 0.640000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.652000] 8021q: 802.1Q VLAN Support v1.8 [ 0.668000] SQUASHFS error: xz decompression failed, data probably corrupt [ 0.676000] SQUASHFS error: squashfs_read_data failed to read block 0x3823aa [ 0.684000] SQUASHFS error: Unable to read metadata cache entry [3823aa] [ 0.688000] SQUASHFS error: Unable to read inode 0x2fdc193c [ 0.696000] VFS: Cannot open root device "mtdblock2" or unknown-block(31,2): error -5 [ 0.704000] Please append a correct "root=" boot option; here are the available partitions: [ 0.712000] 1f00 128 mtdblock0 (driver?) [ 0.716000] 1f01 1233 mtdblock1 (driver?) [ 0.724000] 1f02 29613 mtdblock2 (driver?) [ 0.728000] 1f03 25984 mtdblock3 (driver?) [ 0.732000] 1f04 30848 mtdblock4 (driver?) [ 0.740000] 1f05 1664 mtdblock5 (driver?) [ 0.744000] 1f06 128 mtdblock6 (driver?) [ 0.748000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2) [ 0.760000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/02/06 18:56
  • by danitool