Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:zyxel:nwa55axe [2024/03/29 18:15] – [ZyXEL NWA55AXE] terikintoh:zyxel:nwa55axe [2024/06/05 09:03] – [OEM bootlog] nokius
Line 386: Line 386:
  
 ===== Bootlogs ===== ===== Bootlogs =====
 +
 ==== OEM bootlog ==== ==== OEM bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE</nowiki>+<nowiki> 
 +U-Boot SPL 2018.09 (Jan 22 2021 - 07:42:43 +0000) 
 +Trying to boot from NAND 
 + 
 +Initializing NMBM ... 
 +Signature found at block 1023 [0x07fe0000] 
 +First info table with writecount 0 found in block 960 
 +Second info table with writecount 0 found in block 963 
 +NMBM has been successfully attached 
 + 
 + 
 +U-Boot 2018.09 (Jan 22 2021 - 07:42:43 +0000) 
 + 
 +CPU:   MediaTek MT7621AT ver 1, eco 3 
 +Clocks: CPU: 880MHz, DDR: 600MHz (1200MT/s), Bus: 220MHz, XTAL: 40MHz 
 +Model: MediaTek MT7621 reference board (NAND) 
 +DRAM:  256 MiB 
 +NAND:  128 MiB 
 + 
 +Initializing NMBM ... 
 +Signature found at block 1023 [0x07fe0000] 
 +First info table with writecount 0 found in block 960 
 +Second info table with writecount 0 found in block 963 
 +NMBM has been successfully attached 
 + 
 +Loading Environment from NMBM... *** Warning - bad CRC, using default environment 
 + 
 +In:    uartlite0@1e000c00 
 +Out:   uartlite0@1e000c00 
 +Err:   uartlite0@1e000c00 
 +Net: 
 +Warning: eth@1e100000 (eth0) using random MAC address - fa:26:d7:78:e2:6c 
 +eth0: eth@1e100000 
 +Reading from 0x7700000, size 0x20000 
 +Succeeded 
 +Zyxel version:V1.03 
 +gpio: pin 6 (gpio 6) value is 1 
 +gpio: pin 24 (gpio 24) value is 0 
 +gpio: pin 24 (gpio 24) value is 1 
 +Hit any key to stop autoboot: 
 +Loading FIT image at offset 0x2980000 to memory 0x83000000, size 0x38ad24 ... 
 +Automatic boot of image at addr 0x83000000 ... 
 +## Loading kernel from FIT Image at 83000000 ... 
 +   Using 'config@1' configuration 
 +   Trying 'kernel@1' kernel subimage 
 +     Description:  MIPS OpenWrt Linux-4.4.198 
 +     Type:         Kernel Image 
 +     Compression:  lzma compressed 
 +     Data Start:   0x830000e4 
 +     Data Size:    3700285 Bytes = 3.5 MiB 
 +     Architecture: MIPS 
 +     OS:           Linux 
 +     Load Address: 0x81001000 
 +     Entry Point:  0x81001000 
 +     Hash algo:    crc32 
 +     Hash value:   68a1444b 
 +     Hash algo:    sha1 
 +     Hash value:   9ff9ef1add755e522a38b8a3ca688862a42f625f 
 +   Verifying Hash Integrity ... crc32+ sha1+ OK 
 +## Loading fdt from FIT Image at 83000000 ... 
 +   Using 'config@1' configuration 
 +   Trying 'fdt@1' fdt subimage 
 +     Description:  MIPS OpenWrt mt7621-rfb-ax-nmbm device tree blob 
 +     Type:         Flat Device Tree 
 +     Compression:  uncompressed 
 +     Data Start:   0x83387868 
 +     Data Size:    12690 Bytes = 12.4 KiB 
 +     Architecture: MIPS 
 +     Hash algo:    crc32 
 +     Hash value:   22dfdc4b 
 +     Hash algo:    sha1 
 +     Hash value:   1d76e5da661e6d2a8eafb4175232705f43e4132c 
 +   Verifying Hash Integrity ... crc32+ sha1+ OK 
 +   Booting using the fdt blob at 0x83387868 
 +   Uncompressing Kernel Image ... OK 
 +   Loading Device Tree to 8fe67000, end 8fe6d191 ... OK 
 +[    0.000000] Linux version 4.4.198 (jenkins@NT121613-PC10) (gcc version 5.4.0 (LEDE GCC 5.4.0 r48+2-a5857a0e) ) #0 SMP Wed Jan 10 06:31:00 UTC 2024 
 +[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 
 +[    0.000000] bootconsole [early0] enabled 
 +[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) 
 +[    0.000000] MIPS: machine is MediaTek MT7621 RFB (802.11ax, NAND with NMBM) 
 +[    0.000000] Determined physical RAM map: 
 +[    0.000000]  memory: 10000000 @ 00000000 (usable) 
 +[    0.000000] CPU Clock: 1000MHz 
 +[    0.688459] zyUMAC_wal_attach: num_radios 2 
 + 
 +[    0.693633] zyUMAC_wal_wphy_create: g_num_radios 2 
 +[    0.693633] Start EnterpriseWLAN system daemon.... 
 +..........................................Applying system configuration file, please wait... 
 +.................................EnterpriseWLAN system is configured successfully with startup-config.conf 
 +netopeer-server start 
 + 
 +Welcome to NWA55AXE 
 +</nowiki>
 </WRAP>\\ </WRAP>\\
  
  • Last modified: 2024/06/05 10:16
  • by nokius