ZyXEL NBG6817

Also known as ZyXEL Armor Z2 AC2600. The hardware is very similar to the ZyXEL NBG6816 (Armor Z1), but uses an all QCA IPQ8065 design (SOC and QCA9984 wlan) instead, like the Netgear Nighthawk x4s (r7800) and the Synology rt2600ac.

Zyxel NBG6817 (Armor Z2)

Supported Versions

Hardware Highlights

Installation

→ Install OpenWrt

Flash Layout

ZyXEL NBG6817 Flash Layout (SPI-NOR): OEM Layout (as specified by the bootloader/ cmdline)
Layer0 raw NOR flash memory chip (m25p80 spi0.0: mx25u3235f) 4096 KiB
Layer1 mtd0 SBL 768 KiB mtd1 TZ 256 KiB mtd2 RPM 256 KiB mtd3 u-boot 512 KiB mtd4 env 64 KiB mtd5 ART 64 KiB mtd6 dualflag 64 KiB mtd7 0:RESERVED 2112 KiB
Size in KiB 768 KiB 256 KiB 256 KiB 512 KiB 64 KiB 64 KiB 64 KiB 2112 KiB
Name SBL TZ RPM u-boot env ART dualflag reserved
mountpoint none none none none none none none none
filesystem none none none none none none none none

4 MB SPI-NOR (OEM partitioning): 

# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 000c0000 00010000 "SBL"
mtd1: 00040000 00010000 "TZ"
mtd2: 00040000 00010000 "RPM"
mtd3: 00080000 00010000 "u-boot"
mtd4: 00010000 00010000 "env"
mtd5: 00010000 00010000 "ART"
mtd6: 00010000 00010000 "dualflag"
mtd7: 00210000 00010000 "reserved"
ZyXEL NBG6817 Flash Layout (SPI-NOR): OpenWrt Layout (derived from qcom-smem)
Layer0 raw NOR flash memory chip (m25p80 spi0.0: mx25u3235f) 4096 KiB
Layer1 mtd0 0:SBL1 128 KiB mtd1 0:MIBIB 128 KiB mtd2 0:SBL2 128 KiB mtd3 0:SBL3 256 KiB mtd4 0:DDRCONFIG 64 KiB mtd5 0:SSD 64 KiB mtd6 0:TZ 256 KiB mtd7 0:RPM 256 KiB mtd8 0:APPSBL 512 KiB mtd9 0:APPSBLENV 64 KiB mtd10 0:ART 64 KiB mtd11 0:DUAL_FLAG 64 KiB mtd12 0:RESERVED 2112 KiB
Size in KiB 128 KiB 128 KiB 128 KiB 256 KiB 64 KiB 64 KiB 256 KiB 256 KiB 512 KiB 64 KiB 64 KiB 64 KiB 2112 KiB
Name 0:SBL1 0:MIBIB 0:SBL2 0:SBL3 0:DDRCONFIG 0:SSD 0:TZ 0:RPM 0:APPSBL 0:APPSBLENV 0:ART 0:DUAL_FLAG 0:RESERVED
mountpoint none none none none none none none none none none none none none
filesystem none none none none none none none none none none none none none

4 MB SPI-NOR (LEDE partitioning): 

# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00020000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00020000 00010000 "0:SBL2"
mtd3: 00040000 00010000 "0:SBL3"
mtd4: 00010000 00010000 "0:DDRCONFIG"
mtd5: 00010000 00010000 "0:SSD"
mtd6: 00040000 00010000 "0:TZ"
mtd7: 00040000 00010000 "0:RPM"
mtd8: 00080000 00010000 "0:APPSBL"
mtd9: 00010000 00010000 "0:APPSBLENV"
mtd10: 00010000 00010000 "0:ART"
mtd11: 00010000 00010000 "0:DUAL_FLAG"
mtd12: 00210000 00010000 "0:RESERVED"
ZyXEL NBG6817 Flash Layout (eMMC): OEM Layout
Layer0 GPT partitioned eMMC flash memory chip (Kingston S10004 mmc0:0001 S10004) 4 GB
Layer1 mmcblk0p1 rootfs_data 4 MiB mmcblk0p2 romd 4 MiB mmcblk0p3 header 1 MiB mmcblk0p4 kernel 4 MiB mmcblk0p5 rootfs 64 MiB mmcblk0p6 header_1 1 MiB mmcblk0p7 kernel_1 4 MiB mmcblk0p8 rootfs_1 64 MiB mmcblk0p9 bu1 256 MiB mmcblk0p10 bu2 3245 MiB
mountpoint / (primary+alternative) none none none / (primary) none none / (alternative) none /tmp/ApplicationData
filesystem OverlayFS none none none OverlayFS (primary) none none OverlayFS (alternative) none ext4
Layer3 rootfs_data (primary+alternative) rootfs (primary) rootfs (alternative) ApplicationData
Size in MiB 4 MiB 4 MiB 1 MiB 4 MiB 64 MiB 1 MiB 4 MiB 64 MiB 256 MiB 3245 MiB
Name rootfs_data romd header kernel rootfs header_1 kernel_1 rootfs_1 bu1 bu2
mountpoint /overlay (primary+alternative) /rom (primary) /rom (alternative) /tmp/ApplicationData
filesystem ext4 none none none SquashFS none none SquashFS none ext4
ZyXEL NBG6817 Flash Layout (eMMC): OpenWrt Layout
Layer0 GPT partitioned eMMC flash memory chip (Kingston S10004 mmc0:0001 S10004) 4 GB
Layer1 mmcblk0p1 rootfs_data 4 MiB mmcblk0p2 romd 4 MiB mmcblk0p3 header 1 MiB mmcblk0p4 kernel 4 MiB mmcblk0p5 rootfs 64 MiB mmcblk0p6 header_1 1 MiB mmcblk0p7 kernel_1 4 MiB mmcblk0p8 rootfs_1 64 MiB mmcblk0p9 bu1 256 MiB mmcblk0p10 bu2 3245 MiB
mountpoint none none none none / (primary) none none / (alternative) none none
filesystem ext4 none none none OverlayFS none none OverlayFS none ext4
Layer3 rootfs (primary) rootfs_data (primary) rootfs (alternative) rootfs_data (alternative)
Size in MiB 4 MiB 4 MiB 1 MiB 4 MiB 64 MiB 1 MiB 4 MiB 64 MiB 256 MiB 3245 MiB
Name rootfs_data romd header kernel rootfs header_1 kernel_1 rootfs_1 bu1 bu2
mountpoint /rom (primary) /overlay (primary) /rom (alternative) /overlay (alternative)
filesystem ext4 none none none SquashFS ext4 none none SquashFS ext4 none ext4

4 GB internal eMMC: 

# gdisk -l /dev/mmcblk0
GPT fdisk (gdisk) version 1.0.3

Partition table scan:
  MBR: protective
  BSD: not present
  APM: not present
  GPT: present

Found valid GPT with protective MBR; using GPT.
Disk /dev/mmcblk0: 7471104 sectors, 3.6 GiB
Sector size (logical): 512 bytes
Disk identifier (GUID): XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
Partition table holds up to 12 entries
Main partition table begins at sector 2 and ends at sector 4
First usable sector is 34, last usable sector is 7471070
Partitions will be aligned on 2-sector boundaries
Total free space is 1 sectors (512 bytes)

Number  Start (sector)    End (sector)  Size       Code  Name
   1              34            8225   4.0 MiB     FFFF  rootfs_data
   2            8226           16417   4.0 MiB     FFFF  romd
   3           16418           18465   1024.0 KiB  FFFF  header
   4           18466           26657   4.0 MiB     FFFF  kernel
   5           26658          157729   64.0 MiB    FFFF  rootfs
   6          157730          159777   1024.0 KiB  FFFF  header_1
   7          159778          167969   4.0 MiB     FFFF  kernel_1
   8          167970          299041   64.0 MiB    FFFF  rootfs_1
   9          299042          823329   256.0 MiB   FFFF  bu1
  10          823330         7471069   3.2 GiB     FFFF  bu2

OEM easy installation

OpenWrt 19.07.0 and newer

openwrt-ipq806x-generic-zyxel_nbg6817-squashfs-factory.bin can be flashed directly from the stock OEM webinterface.

Obsolete: LEDE 17.01.x/ OpenWrt 18.06.x

Since 19.07.0, factory images allowing to install OpenWrt directly from the OEM webinterface are provided, this is much easier and safer than the manual installation methods necessary for older releases. If testing an older release is deemed necessary for any reason, it's safer to install 19.07.0 first, and to downgrade from there via “sysupgrade -n <sysupgrade-image.bin>”, than to use the obsolete procedure explained below.

Telnet and/ or SSH can be enabled in the OEM firmware, this allows flashing LEDE from the shell. 

# printf "\xff" >/dev/mtdblock6   #warning, only do this from the OEM firmware!
# cat /tmp/openwrt-ipq806x-NBG6817-squashfs-mmcblk0p4-kernel.bin >/dev/mmcblk0p4
# cat /tmp/openwrt-ipq806x-NBG6817-squashfs-mmcblk0p5-rootfs.bin >/dev/mmcblk0p5
# sync
# reboot -f

OEM installation using the TFTP method

Requires factory images for OpenWrt 19.07.0 or newer, see debricking for details.

→ generic.flashing.tftp

Specific values needed for tftp

Bootloader tftp client IPv4 address 192.168.1.1
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “factory”, rename to “ras.bin”.)
TFTP transfer window 3 seconds
TFTP window start approximately 1 seconds after power on
TFTP server required IP address 192.168.1.99

Upgrading OpenWrt

→ generic.sysupgrade

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/releases/XX.XX.X/targets/ipq806x/generic/openwrt-18.06.1-ipq806x-zyxel_nbg6817-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-ipq806x-zyxel_nbg6817-squashfs-sysupgrade.bin

XX.XX.X = Latest stable release from the “Firmware OpenWrt Upgrade URL” link above

If you are upgrading with a custom-built image, you must check a couple of items (these are chosen incorrectly at v18.06.1 by the make menuconfig process when you select this hardware type):

  • Select firmware for ath10k QCA9984 (QCA99x0 is selected automatically)
  • Select full version of losetup (not busybox version...neither is selected automatically, but losetup is necessary for subsequent sysupgrades)

Debricking

The device is able to flash from a tftp server. You have to fullfill the following requirements:

  • Configure your server to 192.168.1.99, netmask 255.255.255.0
  • Copy your firmware file into the tftp root directory and rename it to “ras.bin” (i.e. download it from zyxel directly or OpenWrt -factory image)
  • Boot up your device holding the WPS (Key) button.

After the image has been flashed (~30s), the power LED will blink quickly and the router needs to be power-cycled. The tftp window is rather short with 3 seconds, which makes it important to reduce the link training to a minimum, adding an unmanaged 100 MBit/s switch between the router's LAN port and the tftp server can help significantly.

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
eth1.1 (vlan1) LAN ports (1 to 4) None
eth0.2 (vlan2) WAN DHCP
wlan0 5Ghz WiFi Disabled
wlan1 2.4Ghz WiFi Disabled

Switch Ports (for VLANs)

Numbers 1-4 are Ports 1-4 as labeled on the unit, number 5 is the Internet (WAN) on the unit. The router uses two CPU ports from the switch, 0 is the internal connection between WAN and the router itself, while 6 is used for the internal connection between LAN and the router itself.

Port Switch port
Internet (WAN) 5
LAN 1 1
LAN 2 2
LAN 3 3
LAN 4 4

Buttons

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The ZyXEL NBG6817 has the following buttons:

BUTTON Event
Reset reset
WiFi Protected Setup wps
WiFi rfkill

Hardware

Info

Photos

See also the FCC images (FCC ID: I88NBG6817).

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Opening the case

Note: This will void your warranty!

Peel off four (4) rubber feet, then remove four (4) Phillips-head screws. Open the case with a spudger -- there are latches spread around, but they probably won't break the first time you pop the lid off.

Remove the screw in the middle of the PCB to allow the board to be moved out a little bit -- enough to solder the serial pins in place.

Main PCB:
Insert photo of PCB

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters
for ZyXEL NBG6817 		115200, 8N1

JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

→ bootloader

Bootlogs

OEM bootloader log

U-Boot 2012.07 [Standard IPQ806X.LN,unknown] (Sep 26 2017 - 15:22:40) smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000 4 MiB MMC: ipq_mmc: 0 In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS cdp: get part failed for rootfs Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 Disable WAN port eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 8c:59:73:XX:XX:XX , eth1 ZyXEL zloader v2.07 (Sep 26 2017 - 15:24:03) MMC read: dev # 0, block # 16418, count 4 ... MMC read: dev # 0, block # 16418, count 4 ... Multiboot clinent version: 2.0 Mac1 unit failed Hit any key to stop autoboot: [countdown] MMC read: dev # 0, block # 18466, count 8192 ... 8192 blocks read: OK Image Name: ARM OpenWrt Linux-4.14.63 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2263614 Bytes = 2.2 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK device nand1 <m25p80>, # parts = 8 #: name size offset mask_flags 0: SBL 0x000c0000 0x00000000 1 1: TZ 0x00040000 0x000c0000 1 2: RPM 0x00040000 0x00100000 1 3: u-boot 0x00080000 0x00140000 1 4: env 0x00010000 0x001c0000 1 5: ART 0x00010000 0x001d0000 1 6: dualflag 0x00010000 0x001e0000 0 7: reserved 0x00210000 0x001f0000 0 active partition: nand1,0 - (SBL) 0x000c0000 @ 0x00000000 defaults: mtdids : none mtdparts: mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,${ldr_psize}(u-boot)${readonly},${env_psize}(env)${readonly},${rfdat_psize}(ART)${readonly},${dualflag_psize}(dualflag),${reserved_psize}(reserved) Setting up atags for msm partition: SBL Setting up atags for msm partition: TZ Setting up atags for msm partition: RPM Setting up atags for msm partition: u-boot Setting up atags for msm partition: env Setting up atags for msm partition: ART Setting up atags for msm partition: dualflag Setting up atags for msm partition: reserved Using machid 0x136d from environment Starting kernel ...


OEM bootlog

root@NBG6817:~# dmesg [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.103 (benny.huang@build-s01) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Mon Mar 20 22:25:58 CST 2017 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: ZyXEL NBG6817 board [ 0.000000] Ignoring unrecognised tag 0x494e4f52 [ 0.000000] msm_reserve_memory: 0x44000000, 0x600000 [ 0.000000] msm_reserve_memory: 0x44600000, 0x200000 [ 0.000000] memory pool 3 (start 5fc00000 size 400000) initialized [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] smem_find(137, 80): wrong size 72 [ 0.000000] socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536 [ 0.000000] accessory_chip=0 hw_plat_subtype=0 [ 0.000000] On node 0 totalpages: 122624 [ 0.000000] Normal zone: 982 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 121642 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0c60000 s10240 r8192 d14336 u32768 [ 0.000000] pcpu-alloc: s10240 r8192 d14336 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121642 [ 0.000000] Kernel command line: board=NBG6817 root=/dev/mmcblk0p8 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 43MB 436MB = 479MB total [ 0.000000] Memory: 477328k/489616k available, 13168k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdf000000 - 0xff000000 ( 512 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdeb00000 ( 491 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0511000 (5156 kB) [ 0.000000] .init : 0xc0600000 - 0xc0702800 (1034 kB) [ 0.000000] .data : 0xc0704000 - 0xc079d840 ( 615 kB) [ 0.000000] .bss : 0xc079d864 - 0xc085c8b0 ( 765 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:1689 [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms [ 0.000000] Console: colour dummy device 80x30 [ 0.150421] Calibrating delay using timer specific routine.. 12.56 BogoMIPS (lpj=62802) [ 0.150452] pid_max: default: 32768 minimum: 301 [ 0.150921] Mount-cache hash table entries: 512 [ 0.152389] CPU: Testing write buffer coherency: ok [ 0.152577] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152608] Setting up static identity map for 0x41891518 - 0x418915a0 [ 0.154951] CPU1: Booted secondary processor [ 0.155014] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.155107] Brought up 2 CPUs [ 0.155107] SMP: Total of 2 processors activated (25.12 BogoMIPS). [ 0.171790] dummy: [ 0.172539] NET: Registered protocol family 16 [ 0.173352] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver [ 0.176163] meminfo_init: smem ram ptable found: ver: 0 len: 5 [ 0.176163] Found 1 memory banks grouped into 8 memory regions [ 0.176476] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio [ 0.177132] smem_find(137, 80): wrong size 72 [ 0.177163] socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536 [ 0.177163] accessory_chip=0 hw_plat_subtype=0 [ 0.177194] msm_rpm_init: RPM firmware 3.0.16777364 [ 0.185254] clk_tbl_nss_fast - loaded [ 0.216432] msm_dmov_memcpy_init: Success [ 0.225616] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20 [ 0.225648] sps:BAM 0x12244000 is registered. [ 0.225898] sps:sps is ready. [ 0.261262] msm_pcie_setup: link initialized [ 0.261668] PCI host bridge to bus 0000:00 [ 0.261668] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff] [ 0.261761] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.262043] pci 0000:00:00.0: supports D1 [ 0.262043] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.262168] PCI: bus0: Fast back to back transfers disabled [ 0.262199] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.262417] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.262511] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit] [ 0.262855] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.262917] PCI: bus1: Fast back to back transfers disabled [ 0.301124] msm_pcie_setup: link initialized [ 0.301499] PCI host bridge to bus 0000:02 [ 0.301530] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff] [ 0.301593] pci 0000:02:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.301874] pci 0000:02:00.0: supports D1 [ 0.301874] pci 0000:02:00.0: PME# supported from D0 D1 D3hot [ 0.301999] PCI: bus2: Fast back to back transfers disabled [ 0.302030] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.302249] pci 0000:03:00.0: [168c:0046] type 00 class 0x028000 [ 0.302343] pci 0000:03:00.0: reg 10: [mem 0x00000000-0x001fffff 64bit] [ 0.302717] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold [ 0.302842] PCI: bus3: Fast back to back transfers disabled [ 2.326647] msm_pcie_setup: link initialization failed [ 2.326866] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 2.326897] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 2.326960] pci 0000:02:00.0: PCI bridge to [bus 03-03] [ 2.326960] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 2.327022] PCI: enabling device 0000:02:00.0 (0140 -> 0143) [ 2.327085] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 2.327116] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 2.327147] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 2.327179] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 2.327210] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 2.348953] bio: create slab <bio-0> at 0 [ 2.350546] SCSI subsystem initialized [ 2.351202] libata version 3.00 loaded. [ 2.352577] spi_qsd spi_qsd.5: master is unqueued, this is deprecated [ 2.355107] spi_qsd spi_qsd.6: master is unqueued, this is deprecated [ 2.360137] Switching to clocksource gp_timer [ 2.382005] NET: Registered protocol family 2 [ 2.391815] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 2.392439] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 2.392627] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 2.392814] TCP: Hash tables configured (established 16384 bind 16384) [ 2.392845] TCP: reno registered [ 2.392845] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.392877] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.393314] NET: Registered protocol family 1 [ 2.393470] PCI: CLS 64 bytes, default 64 [ 2.395189] smd: register irq failed on wcnss_a11 [ 2.395220] smd: deregistering IRQs [ 2.395251] SMD: smd_core_platform_init() failed [ 2.410153] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0 [ 2.410371] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 5 [ 2.418650] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported [ 2.418681] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported [ 2.420399] msm_rpm_log_probe: OK [ 2.443080] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.443111] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 2.444423] msgmni has been set to 932 [ 2.445954] Asymmetric key parser 'x509' registered [ 2.445985] io scheduler noop registered [ 2.446016] io scheduler deadline registered (default) [ 2.447391] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.450046] msm_serial_hs.0: ttyHS0 at MMIO 0x12490000 (irq = 227) is a MSM HS UART [ 2.450702] msm_serial_hs module loaded [ 2.450890] msm_serial_hsl: detected port #1 [ 2.451046] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM [ 2.451452] msm_serial_hsl: console setup on port #1 [ 3.140424] console [ttyHSL1] enabled [ 3.143861] msm_serial_hsl: driver initialized [ 3.153608] ahci ahci.0: forcing PORTS_IMPL to 0x1 [ 3.157419] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.165354] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 3.174695] scsi0 : ahci_platform [ 3.177694] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241 [ 3.187503] m25p80 spi5.0: found mx25u3235f, expected s25fl512s [ 3.192814] m25p80 spi5.0: mx25u3235f (4096 Kbytes) [ 3.197250] 8 cmdlinepart partitions found on MTD device m25p80 [ 3.203217] Creating 8 MTD partitions on "m25p80": [ 3.207935] 0x000000000000-0x0000000c0000 : "SBL" [ 3.214526] 0x0000000c0000-0x000000100000 : "TZ" [ 3.219868] 0x000000100000-0x000000140000 : "RPM" [ 3.225616] 0x000000140000-0x0000001c0000 : "u-boot" [ 3.231271] 0x0000001c0000-0x0000001d0000 : "env" [ 3.236676] 0x0000001d0000-0x0000001e0000 : "ART" [ 3.241986] 0x0000001e0000-0x0000001f0000 : "dualflag" [ 3.247578] 0x0000001f0000-0x000000400000 : "reserved" [ 3.282505] GPIO Bitbanged MDIO: probed [ 3.285567] i2c /dev entries driver [ 3.294845] cpuidle: using governor ladder [ 3.297906] cpuidle: using governor menu [ 3.302655] mmc0: SDCC Version: 0x06000018 [ 3.306154] mmc0: bam physical base=0x12402000 [ 3.310434] mmc0: bam virtual base=0xdf0a0000 [ 3.314651] sps:BAM 0x12402000 is registered. [ 3.318837] mmc0: BAM device registered. bam_handle=0xde1f4200 [ 3.324835] sps:BAM 0x12402000 enabled: ver:0x5, number of pipes:6 [ 3.331084] mmc0: Qualcomm MSM SDCC-BAM at 0x0000000012402000 irq 130 [ 3.337425] mmc0: Qualcomm MSM SDCC-DML at 0x0000000012400800 [ 3.343267] mmc0: No card detect facilities available [ 3.350984] mmc0: Qualcomm MSM SDCC-core at 0x0000000012400000 irq 136,0 dma -1 dmacrcri -1 [ 3.358294] mmc0: Controller capabilities: 0x0000019a [ 3.363761] mmc0: 8 bit data mode enabled [ 3.367322] mmc0: 4 bit data mode disabled [ 3.371446] mmc0: polling status mode disabled [ 3.375882] mmc0: MMC clock 400000 -> 96000000 Hz, PCLK 0 Hz [ 3.386597] mmc0: Slot eject status = 0 [ 3.395501] mmc0: Power save feature enable = 1 [ 3.401093] mmc0: SPS-BAM data transfer mode available [ 3.410465] mmc1: SDCC Version: 0x06000018 [ 3.418837] mmc1: bam physical base=0x12182000 [ 3.427335] mmc1: bam virtual base=0xdf0dc000 [ 3.435738] sps:BAM 0x12182000 is registered. [ 3.443986] mmc1: BAM device registered. bam_handle=0xde1f4a00 [ 3.453983] sps:BAM 0x12182000 enabled: ver:0x5, number of pipes:6 [ 3.464448] mmc1: Qualcomm MSM SDCC-BAM at 0x0000000012182000 irq 128 [ 3.475132] mmc1: Qualcomm MSM SDCC-DML at 0x0000000012180800 [ 3.485035] mmc1: No card detect facilities available [ 3.493595] mmc1: Qualcomm MSM SDCC-core at 0x0000000012180000 irq 134,0 dma -1 dmacrcri -1 [ 3.500968] mmc1: Controller capabilities: 0x0000019a [ 3.505998] mmc1: 8 bit data mode disabled [ 3.510090] mmc1: 4 bit data mode enabled [ 3.514120] mmc1: polling status mode disabled [ 3.518556] mmc1: MMC clock 400000 -> 192000000 Hz, PCLK 0 Hz [ 3.524273] mmc1: Slot eject status = 0 [ 3.528084] mmc1: Power save feature enable = 1 [ 3.532583] mmc1: SPS-BAM data transfer mode available [ 3.538519] TCP: cubic registered [ 3.540268] ata1: SATA link down (SStatus 0 SControl 300) [ 3.546516] NET: Registered protocol family 17 [ 3.550952] Bridge firewalling registered [ 3.554795] 8021q: 802.1Q VLAN Support v1.8 [ 3.559075] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 3.566697] Registering SWP/SWPB emulation handler [ 3.571602] clock_late_init: Removing enables held for handed-off clocks [ 3.581568] mmc0: new high speed MMC card at address 0001 [ 3.586816] mmcblk0: mmc0:0001 S10004 3.56 GiB [ 3.594720] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff [ 3.599343] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff [ 3.605029] no pmic restart interrupt specified [ 3.609903] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 [ 3.782068] VFS: Mounted root (squashfs filesystem) readonly on device 179:8. [ 3.788659] Freeing init memory: 1032K [ 8.614870] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 8.742705] usbcore: registered new interface driver usbfs [ 8.751452] usbcore: registered new interface driver hub [ 8.762355] usbcore: registered new device driver usb [ 8.822180] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.827741] msm_hsusb_host msm_hsusb_host: unable to find transceiver [ 8.837613] Initializing USB Mass Storage driver... [ 8.841518] usbcore: registered new interface driver usb-storage [ 8.847422] USB Mass Storage support registered. [ 32.249328] ocf: module license 'BSD' taints kernel. [ 32.253327] Disabling lock debugging due to kernel taint [ 32.356888] ssdk_plat_init start [ 32.359137] Register QCA PHY driver [ 32.367947] PHY ID is 0x4dd036 [ 32.545017] qca probe f1 phy driver succeeded! [ 32.548422] qca-ssdk module init succeeded! [ 32.626148] NET: Registered protocol family 10 [ 32.829959] md: linear personality registered for level -1 [ 32.863323] md: raid0 personality registered for level 0 [ 32.875320] md: raid1 personality registered for level 1 [ 32.887503] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 32.968791] NET: Registered protocol family 15 [ 32.987004] Initializing XFRM netlink socket [ 33.043017] PPP generic driver version 2.4.2 [ 33.078288] tun: Universal TUN/TAP device driver, 1.6 [ 33.082318] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 33.110715] PPP MPPE Compression module registered [ 33.122336] ********************************************************** [ 33.127803] * Driver :NSS GMAC Driver for RTL v(3.72a) [ 33.133208] * Version :1.0 [ 33.136051] * Copyright :Copyright (c) 2013-2015 The Linux Foundation. All rights reserved. [ 33.144486] ********************************************************** [ 33.151327] GMAC1(de0a4c80) Invalid MAC@ - using 06:07:08:09:0a:0b [ 33.162949] GMAC2(de0a6480) Invalid MAC@ - using d6:d7:d8:d9:da:db [ 35.944923] L2TP core driver, V2.0 [ 35.954795] L2TP netlink interface [ 36.076444] nss_driver - fw of size 434240 bytes copied to load addr: 40000000, nss_id : 0 [ 36.106654] nss_driver - Turbo Support 1 [ 36.109621] Supported Frequencies - 110Mhz 600Mhz 800Mhz [ 36.149953] nss_driver - fw of size 189248 bytes copied to load addr: 40800000, nss_id : 1 [ 36.167728] Error - Duplicate Interface CB Registered for interface 107 [ 36.173320] Error - Duplicate Interface CB Registered for interface 110 [ 36.208028] IPv6 over IPv4 tunneling driver [ 36.239081] <NSS-CRYPTO>:Register with NSS driver- [ 36.250577] Crypto bench loaded build (Mar 21 2017, 13:52:15) [ 36.288784] nss_macsec init success [ 36.339706] gre: GRE over IPv4 demultiplexor driver [ 36.351483] ip_gre: GRE over IPv4 tunneling driver [ 36.379631] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 36.481786] ip_tables: (C) 2000-2006 Netfilter Core Team [ 36.605654] NET: Registered protocol family 24 [ 36.851546] nf_conntrack version 0.5.0 (7474 buckets, 29896 max) [ 36.989284] PPPoL2TP kernel driver, V2.0 [ 36.999906] PPTP driver version 0.8.5 [ 37.010746] QCA multicast snooping installed successfully [ 37.319275] xt_time: kernel timezone is -0000 [ 37.624835] nf_conntrack_rtsp v0.6.21 loading [ 37.635738] nf_nat_rtsp v0.6.21 loading [ 37.664792] xt_RAWNAT: Unknown symbol ipv6_find_hdr (err 0) [ 37.677257] Netfilter messages via NETLINK v0.30. [ 37.745454] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 37.847703] ctnetlink v0.93: registering with nfnetlink. [ 37.918806] ipq-dwc3 ipq-dwc3.0: unable to read platform data num of dbm eps [ 38.025210] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 38.029272] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 [ 38.036519] xhci-hcd xhci-hcd.0: irq 237, io mem 0x10000000 [ 38.042268] xHCI xhci_add_endpoint called for root hub [ 38.042299] xHCI xhci_check_bandwidth called for root hub [ 38.042361] hub 1-0:1.0: USB hub found [ 38.045735] hub 1-0:1.0: 1 port detected [ 38.049765] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 38.055888] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 [ 38.062261] xHCI xhci_add_endpoint called for root hub [ 38.062261] xHCI xhci_check_bandwidth called for root hub [ 38.062324] hub 2-0:1.0: USB hub found [ 38.065791] hub 2-0:1.0: 1 port detected [ 38.071383] ipq-dwc3 ipq-dwc3.1: unable to read platform data num of dbm eps [ 38.177756] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 38.181786] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3 [ 38.189034] xhci-hcd xhci-hcd.1: irq 142, io mem 0x11000000 [ 38.194814] xHCI xhci_add_endpoint called for root hub [ 38.194814] xHCI xhci_check_bandwidth called for root hub [ 38.194876] hub 3-0:1.0: USB hub found [ 38.198250] hub 3-0:1.0: 1 port detected [ 38.202311] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 38.207216] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4 [ 38.214589] xHCI xhci_add_endpoint called for root hub [ 38.214589] xHCI xhci_check_bandwidth called for root hub [ 38.214682] hub 4-0:1.0: USB hub found [ 38.218150] hub 4-0:1.0: 1 port detected [ 38.307341] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. [ 38.401062] ECM init [ 38.402749] ECM init complete [ 38.413214] Registered led device: POWER [ 38.413277] Registered led device: WiFi_5G [ 38.413339] Registered led device: WiFi_2G [ 38.413402] Registered led device: INTERNET [ 38.441049] usbcore: registered new interface driver usblp [ 38.505935] fuse init (API version 7.18) [ 40.740081] <NSS-CRYPTO>:NSS Firmware initialized [ 40.740174] <NSS-CRYPTO>:probing engine - 0 [ 40.740331] <NSS-CRYPTO>:init completed for Pipe Pair[0] [ 40.740362] <NSS-CRYPTO>:init completed for Pipe Pair[1] [ 40.740362] <NSS-CRYPTO>:init completed for Pipe Pair[2] [ 40.740393] <NSS-CRYPTO>:init completed for Pipe Pair[3] [ 40.741049] <NSS-CRYPTO>:probing engine - 1 [ 40.741143] <NSS-CRYPTO>:init completed for Pipe Pair[0] [ 40.741143] <NSS-CRYPTO>:init completed for Pipe Pair[1] [ 40.741174] <NSS-CRYPTO>:init completed for Pipe Pair[2] [ 40.741205] <NSS-CRYPTO>:init completed for Pipe Pair[3] [ 40.741830] <NSS-CRYPTO>:probing engine - 2 [ 40.741924] <NSS-CRYPTO>:init completed for Pipe Pair[0] [ 40.741955] <NSS-CRYPTO>:init completed for Pipe Pair[1] [ 40.741955] <NSS-CRYPTO>:init completed for Pipe Pair[2] [ 40.741986] <NSS-CRYPTO>:init completed for Pipe Pair[3] [ 40.742611] <NSS-CRYPTO>:probing engine - 3 [ 40.742705] <NSS-CRYPTO>:init completed for Pipe Pair[0] [ 40.742736] <NSS-CRYPTO>:init completed for Pipe Pair[1] [ 40.742767] <NSS-CRYPTO>:init completed for Pipe Pair[2] [ 40.742799] <NSS-CRYPTO>:init completed for Pipe Pair[3] [ 42.218462] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: commit=1 [ 43.587847] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 45.464354] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 45.466166] eth1: 1000 Mbps Full Duplex [ 46.491440] device eth1 entered promiscuous mode [ 46.491815] br-lan: port 1(eth1) entered forwarding state [ 46.491815] br-lan: port 1(eth1) entered forwarding state [ 46.493502] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 46.495064] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 47.795376] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) [ 47.804498] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 47.813183] ath_dfs: Version 2.0.0 [ 47.813183] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 47.822649] ath_spectral: Version 2.0.0 [ 47.822649] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 47.822680] SPECTRAL module built on Mar 20 2017 21:33:54 [ 47.847204] ath_tx99: Version 2.0 [ 47.847204] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved [ 47.895157] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 48.131333] ath_pci: (Atheros/multi-bss) [ 48.131396] ol_ath_pci_probe: PCI device id 0046 :0046 [ 48.131396] PCI: enabling device 0000:01:00.0 (0140 -> 0142) [ 48.131521] *********** Cascade ************* [ 48.131615] ath_pci 0000:01:00.0: ath DEBUG: sc=0xdc8de000 [ 48.131615] [ 48.131615] ol_ath_pci_configure : num_desired MSI set to 0 [ 48.131646] [ 48.131646] Using PCI Legacy Interrupt [ 48.131646] chip_id 0xa chip_revision 0x0 [ 48.131677] nss register id -1 offload mode enabled = 0 nss config 0 Target Type a [ 48.141424] [ 48.141424] CLOCK PLL skipped [ 48.143548] __ol_ath_attach: dev name wifi0 [ 48.143580] ol_ath_attach() BMI inited. [ 48.143705] ol_ath_attach() BMI Get Target Info. [ 48.143705] Chip id: 0xa, chip version: 0x1000000 [ 48.143705] [ 48.143705] CE WAR Disabled [ 48.143892] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 48.144079] ol_ath_attach() configure Target . [ 48.144142] [ 48.144142] Target Version is 1000000 [ 48.144173] [ 48.144173] Flash Download Address c0000 [ 48.144173] ol_transfer_bin_file: flash data file defined [ 48.144173] Cal location [0]: 00000000 [ 48.144236] [ 48.144236] Wifi0 NAND FLASH Select OFFSET 0x1000 [ 48.162730] qc98xx_verify_checksum: flash checksum passed: 0x334d [ 48.162761] ol_transfer_bin_file 3805: Download Flash data len 12064 [ 48.162917] Board extended Data download address: 0x0 [ 48.183067] [ 48.183067] Board data initialized [ 48.183255] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 48.183255] [ 48.183255] Selecting OTP binary for CHIP Version 0 [ 48.245860] ol_transfer_bin_file 3662: downloading file 0, Download data len 8920 [ 48.275382] [ 48.275382] First OTP send param 8000 [ 48.490034] br-lan: port 1(eth1) entered forwarding state [ 50.487503] ol_ath_download_firmware :First OTP download and Execute is good address:0x400 return param 4660 [ 50.487503] ol_ath_download_firmware:##Board Id 1 , CHIP Id 0 [ 50.487628] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 50.506685] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9984/hw.1/boardData_QCA9984_CUS239_5G_v1_001.bin [ 50.540018] ol_transfer_bin_file 3662: downloading file 3, Download data len 12064 [ 50.540331] Board extended Data download address: 0x0 [ 50.560293] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 50.560324] [ 50.560324] Selecting OTP binary for CHIP Version 0 [ 50.650140] ol_transfer_bin_file 3662: downloading file 0, Download data len 8920 [ 50.679162] [ 50.679162] [Flash] : Ignore Module param [ 50.679162] [ 50.679162] Second otp download Param 10000 [ 52.898812] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 52.898812] [ 52.898844] Mission mode: Firmware CHIP Version 0 [ 52.979850] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 [ 53.052983] Swap: bytes_left to copy: fw:16; dma_page:70336 [ 53.053014] Swap: wrong length read:0 [ 53.053014] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 191808 Target address 41b608 [ 53.053108] scn=d8fc0480 target_write_addr=41b608 seg_info=da81b710 [ 53.053108] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 53.053139] bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin [ 53.054076] ol_transfer_bin_file: Downloading firmware file: QCA9984/hw.1/athwlan.bin [ 53.222055] ol_transfer_bin_file 3662: downloading file 1, Download data len 361412 [ 53.447828] mc_netlink_receive: Disable bridge snooping! [ 53.805779] mc_netlink_receive: Enable bridge snooping! [ 54.417338] ol_ath_attach() Download FW done. [ 54.417338] ol_ath_attach() HT Create . [ 54.417369] ol_ath_attach() HIF Claim. [ 54.417432] ol_ath_attach() BMI Done. [ 54.417432] ol_ath_attach 6796 host_enable 0 nss_nwifi_offload 0 [ 54.417432] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 54.417432] OL_ACBKMinfree : 0 [ 54.417463] OL_ACBEMinfree : 0 [ 54.417463] OL_ACVIMinfree : 0 [ 54.417463] OL_ACVOMinfree : 0 [ 54.417494] ol_ath_attach() WMI attached. wmi_handle d8420000 [ 54.420493] CE_recv_buf_enqueue 853 Populate last entry 512 for CE 5 [ 54.420493] CE_recv_buf_enqueue 862 CE 5 wi 511 dest_ptr 0x5909f040 nbytes 0 recv_ctxt 0xdad0cd80 [ 54.422930] Startup Mode-0 set [ 54.422930] pdev attach (null) -1 [ 54.422930] [ 54.422930] <=== cfg max peer id 1056 ====> [ 54.423055] HTC Service:0x0300 ep:1 TX flow control disabled [ 54.424648] htt_peer_map_timer_init Enter pdev d7c20000 hrtimer d7c248b8 [ 54.424648] [ 54.424648] htt_alloc_peer_map_mem : Alloc Success : host q vaddr d7c2c000 paddr 5912c000 [ 54.424648] [ 54.424648] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 54.424711] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 54.424773] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d78a0000 [ 54.425210] HTC Service:0x0100 ep:2 TX flow control disabled [ 54.425866] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 54.425898] Firmware_Build_Number:68 [ 54.425898] num_rf_chain:0x00000004 ht_cap_info:0x0000085b vht_cap_info:0x339b79f2 vht_supp_mcs:0x0000ffea [ 54.425898] [ 54.425898] RES CFG Support wmi_service_bitmap 9778 [ 54.425898] [ 54.425929] Sending HOST PLATFORM as 0 to TGT [ 54.425929] ol_ath_service_ready_event: tt_support: 1 [ 54.425929] Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 54.425960] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 [ 54.425991] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, [ 54.425991] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 [ 54.426054] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, [ 54.426054] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 [ 54.426210] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, [ 54.426210] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1440 actual units 531 [ 54.426398] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 177 unit_len 1440, [ 54.426585] ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 177 unit_len 1440, [ 54.426710] ol_ath_alloc_host_mem_chunk req_id 1 idx 5 num_units 177 unit_len 1440, [ 54.426741] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 [ 54.426804] ol_ath_alloc_host_mem_chunk req_id 6 idx 6 num_units 35 unit_len 3072, [ 54.426804] idx 5 req 7 num_units 1 num_unit_info 0 unit size 12288 actual units 1 [ 54.426804] ol_ath_alloc_host_mem_chunk req_id 7 idx 7 num_units 1 unit_len 12288, [ 54.426835] idx 6 req 5 num_units 0 num_unit_info 2 unit size 1876 actual units 531 [ 54.426929] ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 132 unit_len 1876, [ 54.427054] ol_ath_alloc_host_mem_chunk req_id 5 idx 9 num_units 133 unit_len 1876, [ 54.427147] ol_ath_alloc_host_mem_chunk req_id 5 idx 10 num_units 133 unit_len 1876, [ 54.427272] ol_ath_alloc_host_mem_chunk req_id 5 idx 11 num_units 133 unit_len 1876, [ 54.427272] chunk 0 len 13568 requested ,ptr 0x5a5e8000 [ 54.427272] chunk 1 len 54272 requested ,ptr 0x58e70000 [ 54.427303] chunk 2 len 217088 requested ,ptr 0x58e80000 [ 54.427303] chunk 3 len 254880 requested ,ptr 0x58ec0000 [ 54.427303] chunk 4 len 254880 requested ,ptr 0x58f00000 [ 54.427303] chunk 5 len 254880 requested ,ptr 0x58f40000 [ 54.427303] chunk 6 len 107520 requested ,ptr 0x58f80000 [ 54.427303] chunk 7 len 12288 requested ,ptr 0x5a4b4000 [ 54.427335] chunk 8 len 247632 requested ,ptr 0x58fc0000 [ 54.427335] chunk 9 len 249508 requested ,ptr 0x58800000 [ 54.427335] chunk 10 len 249508 requested ,ptr 0x58840000 [ 54.427335] chunk 11 len 249508 requested ,ptr 0x58880000 [ 54.500562] wmi_ready_event_rx: WMI UNIFIED READY event [ 54.500624] ol_ath_connect_htc() WMI is ready [ 54.500687] target uses HTT version 2.2; host uses 2.2 [ 54.505716] ol_ath_attach() connect HTC. [ 54.505716] bypasswmi : 0 [ 54.505716] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 54.505748] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 [ 54.505779] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 [ 54.505779] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 [ 54.505779] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 [ 54.505779] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 [ 54.505810] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 [ 54.505810] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 [ 54.505810] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 [ 54.505841] Add VHT80 channel: 5210 [ 54.505841] Add VHT80 channel: 5290 [ 54.505841] Add VHT80 channel: 5530 [ 54.505873] Add VHT80 channel: 5610 [ 54.505873] Add VHT80 channel: 5690 [ 54.505873] Add VHT80 channel: 5775 [ 54.505873] Skipping VHT80 channel 5825 [ 54.505873] Add VHT80_80 channels: 5210 : 5290 [ 54.505904] Add VHT80_80 channels: 5290 : 5210 [ 54.505904] Add VHT80_80 channels: 5530 : 5610 [ 54.505904] Add VHT80_80 channels: 5610 : 5530 [ 54.505966] Add VHT80_80 channels: 5210 : 5530 [ 54.505966] Add VHT80_80 channels: 5530 : 5210 [ 54.505966] Add VHT80_80 channels: 5210 : 5610 [ 54.505966] Add VHT80_80 channels: 5610 : 5210 [ 54.505966] Add VHT80_80 channels: 5210 : 5690 [ 54.505966] Add VHT80_80 channels: 5690 : 5210 [ 54.505998] Add VHT80_80 channels: 5210 : 5775 [ 54.505998] Add VHT80_80 channels: 5775 : 5210 [ 54.505998] Add VHT80_80 channels: 5290 : 5530 [ 54.505998] Add VHT80_80 channels: 5530 : 5290 [ 54.505998] Add VHT80_80 channels: 5290 : 5610 [ 54.505998] Add VHT80_80 channels: 5610 : 5290 [ 54.506029] Add VHT80_80 channels: 5290 : 5690 [ 54.506029] Add VHT80_80 channels: 5690 : 5290 [ 54.506029] Add VHT80_80 channels: 5290 : 5775 [ 54.506029] Add VHT80_80 channels: 5775 : 5290 [ 54.506029] Add VHT80_80 channels: 5530 : 5690 [ 54.506029] Add VHT80_80 channels: 5690 : 5530 [ 54.506029] Add VHT80_80 channels: 5530 : 5775 [ 54.506060] Add VHT80_80 channels: 5775 : 5530 [ 54.506060] Add VHT80_80 channels: 5610 : 5775 [ 54.506060] Add VHT80_80 channels: 5775 : 5610 [ 54.506060] Add VHT80_80 channels: 5690 : 5775 [ 54.506060] Add VHT80_80 channels: 5775 : 5690 [ 54.508653] ol_ath_phyerr_attach: called [ 54.508809] OL Resmgr Init-ed [ 54.508840] ieee80211_bsteering_attach: Band steering initialized [ 54.508872] acfg_attach: 5845: Netlink socket created:d8410e00 [ 54.508872] ol_if_spectral_setup [ 54.508872] SPECTRAL : get_capability not registered [ 54.508872] HAL_CAP_PHYDIAG : Capable [ 54.508903] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) [ 54.508903] SPECTRAL : get_capability not registered [ 54.508903] HAL_CAP_RADAR : Capable [ 54.508903] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 54.508903] (spectral_attach : 242) [ 54.508903] SPECTRAL : get_capability not registered [ 54.508903] HAL_CAP_SPECTRAL_SCAN : Capable [ 54.508934] SPECTRAL : get_tsf64 not registered [ 54.508934] spectral_init_netlink 78 NULL SKB [ 54.508934] Green-AP : Green-AP : Attached [ 54.508934] [ 54.508934] Green-AP : Attached [ 54.508965] rate power table override is only supported for AR98XX [ 54.508965] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. [ 54.508965] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 54.508997] ieee80211com_init_netlink: 3350: Wifipos 1st Netlink socket created:d8411c00 [ 54.508997] ol_if_dfs_setup: called [ 54.509028] ol_if_dfs_attach: called; ptr=d73c1984, radar_info=d9687bb8 [ 54.509028] dfs_attach: event log enabled by default [ 54.509215] ol_ath_rtt_meas_report_attach: called [ 54.510465] ol_ath_attach() UMAC attach . [ 54.510527] ol_if_dfs_configure: called [ 54.510527] ol_if_dfs_configure: FCC domain [ 54.510559] ol_if_dfs_disable: called [ 54.510590] ol_ath_attach: Calling ol_if_dfs_configure [ 54.510590] [ 54.510590] BURSTING enabled by default [ 54.510715] osif_wrap_attach:432 osif wrap attached [ 54.510746] osif_wrap_devt_init:393 osif wrap dev table init done [ 54.510746] Wrap Attached: Wrap_com =d8410200 ic->ic_wrap_com=d8410200 &wrap_com->wc_devt=d8410200 [ 54.510746] __ol_ath_attach: needed_headroom reservation 60 [ 54.512058] ol_ath_thermal_mitigation_attach: -- [ 54.512308] ol_ath_pci_probe: PCI device id 0046 :0046 [ 54.512371] PCI: enabling device 0000:03:00.0 (0140 -> 0142) [ 54.512746] *********** Cascade ************* [ 54.513089] ath_pci 0000:03:00.0: ath DEBUG: sc=0xd83b2000 [ 54.513120] [ 54.513120] ol_ath_pci_configure : num_desired MSI set to 0 [ 54.513214] [ 54.513214] Using PCI Legacy Interrupt [ 54.513277] chip_id 0xa chip_revision 0x0 [ 54.513339] nss register id -1 offload mode enabled = 0 nss config 0 Target Type a [ 54.524367] [ 54.524367] CLOCK PLL skipped [ 54.526429] __ol_ath_attach: dev name wifi1 [ 54.526491] ol_ath_attach() BMI inited. [ 54.526585] ol_ath_attach() BMI Get Target Info. [ 54.526585] Chip id: 0xa, chip version: 0x1000000 [ 54.526616] [ 54.526616] CE WAR Disabled [ 54.526741] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 54.526991] ol_ath_attach() configure Target . [ 54.527085] [ 54.527085] Target Version is 1000000 [ 54.527085] [ 54.527085] Flash Download Address c0000 [ 54.527116] ol_transfer_bin_file: flash data file defined [ 54.527116] Cal location [1]: 00004000 [ 54.527335] [ 54.527335] wifi1 NAND FLASH Select OFFSET 0x5000 [ 54.546173] qc98xx_verify_checksum: flash checksum passed: 0xda75 [ 54.546173] ol_transfer_bin_file 3805: Download Flash data len 12064 [ 54.546391] Board extended Data download address: 0x0 [ 54.569821] [ 54.569821] Board data initialized [ 54.570009] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 54.570009] [ 54.570009] Selecting OTP binary for CHIP Version 0 [ 54.648203] ol_transfer_bin_file 3662: downloading file 0, Download data len 8920 [ 54.677850] [ 54.677850] First OTP send param 8000 [ 55.422805] [wifi0] FWLOG: [55569] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [ 55.422867] [wifi0] FWLOG: [55569] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [ 55.422867] [wifi0] FWLOG: [55569] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [ 55.422899] [wifi0] FWLOG: [55569] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) [ 56.889971] ol_ath_download_firmware :First OTP download and Execute is good address:0x800 return param 4660 [ 56.889971] ol_ath_download_firmware:##Board Id 2 , CHIP Id 0 [ 56.890096] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 56.890128] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9984/hw.1/boardData_QCA9984_CUS260_2G_v1_002.bin [ 56.953327] ol_transfer_bin_file 3662: downloading file 3, Download data len 12064 [ 56.953545] Board extended Data download address: 0x0 [ 56.973976] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 56.974008] [ 56.974008] Selecting OTP binary for CHIP Version 0 [ 57.053077] ol_transfer_bin_file 3662: downloading file 0, Download data len 8920 [ 57.082724] [ 57.082724] [Flash] : Ignore Module param [ 57.082755] [ 57.082755] Second otp download Param 10000 [ 57.496657] Switching to Tx Mode-1 Threshold 1000 [ 59.302405] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 59.302405] [ 59.302405] Mission mode: Firmware CHIP Version 0 [ 59.359918] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 [ 59.460137] Swap: bytes_left to copy: fw:16; dma_page:70336 [ 59.460137] Swap: wrong length read:0 [ 59.460137] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 191808 Target address 41b608 [ 59.460293] scn=d7480480 target_write_addr=41b608 seg_info=dda74d10 [ 59.460293] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 59.460293] bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin [ 59.460324] ol_transfer_bin_file: Downloading firmware file: QCA9984/hw.1/athwlan.bin [ 59.561355] ol_transfer_bin_file 3662: downloading file 1, Download data len 361412 [ 60.742611] ol_ath_attach() Download FW done. [ 60.742611] ol_ath_attach() HT Create . [ 60.742642] ol_ath_attach() HIF Claim. [ 60.742705] ol_ath_attach() BMI Done. [ 60.742705] ol_ath_attach 6796 host_enable 0 nss_nwifi_offload 0 [ 60.742736] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 60.742736] OL_ACBKMinfree : 0 [ 60.742736] OL_ACBEMinfree : 0 [ 60.742736] OL_ACVIMinfree : 0 [ 60.742736] OL_ACVOMinfree : 0 [ 60.742767] ol_ath_attach() WMI attached. wmi_handle d7570000 [ 60.745454] CE_recv_buf_enqueue 853 Populate last entry 512 for CE 5 [ 60.745485] CE_recv_buf_enqueue 862 CE 5 wi 511 dest_ptr 0x58696040 nbytes 0 recv_ctxt 0xdd629240 [ 60.748203] Startup Mode-0 set [ 60.748203] pdev attach (null) -1 [ 60.748203] [ 60.748234] <=== cfg max peer id 1056 ====> [ 60.748359] HTC Service:0x0300 ep:1 TX flow control disabled [ 60.749890] htt_peer_map_timer_init Enter pdev d7218000 hrtimer d721c8b8 [ 60.749890] [ 60.749890] htt_alloc_peer_map_mem : Alloc Success : host q vaddr d6e80000 paddr 58380000 [ 60.749890] [ 60.749890] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 60.749984] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 60.750109] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d6ea0000 [ 60.751858] HTC Service:0x0100 ep:2 TX flow control disabled [ 60.752608] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 60.752608] Firmware_Build_Number:68 [ 60.752608] num_rf_chain:0x00000004 ht_cap_info:0x0000085b vht_cap_info:0x339b79f2 vht_supp_mcs:0x0000ffea [ 60.752639] [ 60.752639] RES CFG Support wmi_service_bitmap 9778 [ 60.752639] [ 60.752639] Sending HOST PLATFORM as 0 to TGT [ 60.752639] ol_ath_service_ready_event: tt_support: 1 [ 60.752671] Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 60.752671] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 [ 60.752733] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, [ 60.752733] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 [ 60.752796] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, [ 60.752796] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 [ 60.752952] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, [ 60.752952] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1440 actual units 531 [ 60.753139] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 177 unit_len 1440, [ 60.753295] ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 177 unit_len 1440, [ 60.753452] ol_ath_alloc_host_mem_chunk req_id 1 idx 5 num_units 177 unit_len 1440, [ 60.753452] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 [ 60.753514] ol_ath_alloc_host_mem_chunk req_id 6 idx 6 num_units 35 unit_len 3072, [ 60.753514] idx 5 req 7 num_units 1 num_unit_info 0 unit size 12288 actual units 1 [ 60.753545] ol_ath_alloc_host_mem_chunk req_id 7 idx 7 num_units 1 unit_len 12288, [ 60.753545] idx 6 req 5 num_units 0 num_unit_info 2 unit size 1876 actual units 531 [ 60.753639] ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 132 unit_len 1876, [ 60.753764] ol_ath_alloc_host_mem_chunk req_id 5 idx 9 num_units 133 unit_len 1876, [ 60.753889] ol_ath_alloc_host_mem_chunk req_id 5 idx 10 num_units 133 unit_len 1876, [ 60.754014] ol_ath_alloc_host_mem_chunk req_id 5 idx 11 num_units 133 unit_len 1876, [ 60.754014] chunk 0 len 13568 requested ,ptr 0x58388000 [ 60.754014] chunk 1 len 54272 requested ,ptr 0x58390000 [ 60.754045] chunk 2 len 217088 requested ,ptr 0x57c00000 [ 60.754045] chunk 3 len 254880 requested ,ptr 0x57c40000 [ 60.754045] chunk 4 len 254880 requested ,ptr 0x57c80000 [ 60.754045] chunk 5 len 254880 requested ,ptr 0x57cc0000 [ 60.754045] chunk 6 len 107520 requested ,ptr 0x57d00000 [ 60.754045] chunk 7 len 12288 requested ,ptr 0x5838c000 [ 60.754076] chunk 8 len 247632 requested ,ptr 0x57d40000 [ 60.754076] chunk 9 len 249508 requested ,ptr 0x57d80000 [ 60.754076] chunk 10 len 249508 requested ,ptr 0x57dc0000 [ 60.754076] chunk 11 len 249508 requested ,ptr 0x57e00000 [ 60.828647] wmi_ready_event_rx: WMI UNIFIED READY event [ 60.828678] ol_ath_connect_htc() WMI is ready [ 60.828741] target uses HTT version 2.2; host uses 2.2 [ 60.833770] ol_ath_attach() connect HTC. [ 60.833801] bypasswmi : 0 [ 60.833801] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 60.833833] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 60.833833] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 60.833833] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 60.833864] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 60.833864] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 60.833864] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 60.833864] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 60.833895] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 60.833895] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 60.833895] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 60.833926] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 60.833926] ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 [ 60.833926] ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 [ 60.833989] ol_ath_phyerr_attach: called [ 60.834083] OL Resmgr Init-ed [ 60.834114] ieee80211_bsteering_attach: Band steering initialized [ 60.834114] acfg_attach: using existing sock d8410e00 [ 60.834114] ol_if_spectral_setup [ 60.834145] SPECTRAL : get_capability not registered [ 60.834145] HAL_CAP_PHYDIAG : Capable [ 60.834145] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) [ 60.834145] SPECTRAL : get_capability not registered [ 60.834145] HAL_CAP_RADAR : Capable [ 60.834176] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 60.834176] (spectral_attach : 242) [ 60.834176] SPECTRAL : get_capability not registered [ 60.834176] HAL_CAP_SPECTRAL_SCAN : Capable [ 60.834176] SPECTRAL : get_tsf64 not registered [ 60.834176] spectral_init_netlink 78 NULL SKB [ 60.834208] Green-AP : Green-AP : Attached [ 60.834208] [ 60.834208] Green-AP : Attached [ 60.834208] rate power table override is only supported for AR98XX [ 60.834239] ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. [ 60.834239] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 60.834239] ieee80211com_init_netlink: Socket already created d8411c00 [ 60.834239] ol_if_dfs_setup: called [ 60.834270] ol_if_dfs_attach: called; ptr=d69e9984, radar_info=d9687bb8 [ 60.834270] dfs_attach: event log enabled by default [ 60.834489] ol_ath_rtt_meas_report_attach: called [ 60.834707] ol_ath_attach() UMAC attach . [ 60.834739] ol_if_dfs_configure: called [ 60.834739] ol_if_dfs_configure: FCC domain [ 60.834739] ol_if_dfs_disable: called [ 60.834770] ol_ath_attach: Calling ol_if_dfs_configure [ 60.834770] [ 60.834770] BURSTING enabled by default [ 60.834895] osif_wrap_attach:432 osif wrap attached [ 60.834926] osif_wrap_devt_init:393 osif wrap dev table init done [ 60.834926] Wrap Attached: Wrap_com =dc94da00 ic->ic_wrap_com=dc94da00 &wrap_com->wc_devt=dc94da00 [ 60.834926] __ol_ath_attach: needed_headroom reservation 60 [ 60.835770] ol_ath_thermal_mitigation_attach: -- [ 60.871227] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 60.871258] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 60.901936] __sa_init_module [ 61.748109] [wifi1] FWLOG: [62012] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [ 61.748141] [wifi1] FWLOG: [62012] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [ 61.748172] [wifi1] FWLOG: [62012] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [ 61.748203] [wifi1] FWLOG: [62012] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) [ 63.824773] Switching to Tx Mode-1 Threshold 1000 [ 64.324586] isCountryCodeValid: EEPROM regdomain 0x0 [ 64.324617] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 [ 64.324617] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 [ 64.324617] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 [ 64.324617] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 [ 64.324648] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 [ 64.324648] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 [ 64.324648] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 [ 64.324648] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 [ 64.324679] Add VHT80 channel: 5210 [ 64.324711] Add VHT80 channel: 5290 [ 64.324711] Add VHT80 channel: 5530 [ 64.324711] Add VHT80 channel: 5610 [ 64.324711] Skipping VHT80 channel 5660 [ 64.324711] Skipping VHT80 channel 5680 [ 64.324711] Skipping VHT80 channel 5700 [ 64.324742] Add VHT80_80 channels: 5210 : 5290 [ 64.324742] Add VHT80_80 channels: 5290 : 5210 [ 64.324742] Add VHT80_80 channels: 5530 : 5610 [ 64.324742] Add VHT80_80 channels: 5610 : 5530 [ 64.324773] Add VHT80_80 channels: 5210 : 5530 [ 64.324773] Add VHT80_80 channels: 5530 : 5210 [ 64.324804] Add VHT80_80 channels: 5210 : 5610 [ 64.324804] Add VHT80_80 channels: 5610 : 5210 [ 64.324804] Add VHT80_80 channels: 5290 : 5530 [ 64.324804] Add VHT80_80 channels: 5530 : 5290 [ 64.324804] Add VHT80_80 channels: 5290 : 5610 [ 64.324804] Add VHT80_80 channels: 5610 : 5290 [ 64.332927] ath_ioctl: SIOC80211IFCREATE CALLED [ 64.332958] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 60:31:97:XX:XX:X5: [ 64.333270] Setting dscp for pdev [ 64.333333] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 64.333364] Enabling TX checksum bit for the vap ath0 features 4000 [ 64.333364] Enabling SG bit for the vap ath0 features 4000 [ 64.333364] Enabling SG bit for the vap ath0 features 4000 [ 64.333364] Enabling TSO bit for the vap ath0 features 4000 [ 64.333364] Enabling LRO bit for the vap ath0 features 4000 [ 64.333801] VAP device ath0 created osifp: (d9159480) os_if: (d699c000) [ 64.343455] siwfreq [ 64.343455] Set freq vap 0 stop send + d699c000 [ 64.343548] Set freq vap 0 stop send -d699c000 [ 64.371383] Set wait done --d699c000 [ 64.376194] ath_ioctl: SIOC80211IFCREATE CALLED [ 64.376226] wmi_unified_vdev_create_send: ID = 1 Type = 1, Subtype = 0 VAP Addr = 66:31:97:XX:XX:X5: [ 64.376601] Setting dscp for pdev [ 64.376663] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 64.376694] Enabling TX checksum bit for the vap ath1 features 4000 [ 64.376694] Enabling SG bit for the vap ath1 features 4000 [ 64.376694] Enabling SG bit for the vap ath1 features 4000 [ 64.376757] Enabling TSO bit for the vap ath1 features 4000 [ 64.376757] Enabling LRO bit for the vap ath1 features 4000 [ 64.377038] VAP device ath1 created osifp: (d6381480) os_if: (d83a0000) [ 64.387253] siwfreq [ 64.387253] Set freq vap 1 stop send + d699c000 [ 64.387347] Set freq vap 1 stop send -d699c000 [ 64.411090] Set wait done --d699c000 [ 64.411090] Set freq vap 1 stop send + d83a0000 [ 64.411215] Set freq vap 1 stop send -d83a0000 [ 64.424617] [wifi0] FWLOG: [65414] WAL_DBGID_DEV_RESET ( 0xc01d, 0x414 ) [ 64.441080] Set wait done --d83a0000 [ 64.446141] ath_ioctl: SIOC80211IFCREATE CALLED [ 64.446204] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 6a:31:97:XX:XX:X5: [ 64.446547] Setting dscp for pdev [ 64.446610] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 64.446610] Enabling TX checksum bit for the vap ath2 features 4000 [ 64.446610] Enabling SG bit for the vap ath2 features 4000 [ 64.446610] Enabling SG bit for the vap ath2 features 4000 [ 64.446610] Enabling TSO bit for the vap ath2 features 4000 [ 64.446641] Enabling LRO bit for the vap ath2 features 4000 [ 64.446954] VAP device ath2 created osifp: (d6383c80) os_if: (d7560000) [ 64.456638] siwfreq [ 64.456638] Set freq vap 2 stop send + d699c000 [ 64.456732] Set freq vap 2 stop send -d699c000 [ 64.481130] Set wait done --d699c000 [ 64.481130] Set freq vap 2 stop send + d83a0000 [ 64.481224] Set freq vap 2 stop send -d83a0000 [ 64.511090] Set wait done --d83a0000 [ 64.511121] Set freq vap 2 stop send + d7560000 [ 64.511184] Set freq vap 2 stop send -d7560000 [ 64.541112] Set wait done --d7560000 [ 64.545985] ath_ioctl: SIOC80211IFCREATE CALLED [ 64.546048] wmi_unified_vdev_create_send: ID = 3 Type = 1, Subtype = 0 VAP Addr = 6e:31:97:XX:XX:X5: [ 64.546391] Setting dscp for pdev [ 64.546454] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 64.546485] Enabling TX checksum bit for the vap ath3 features 4000 [ 64.546485] Enabling SG bit for the vap ath3 features 4000 [ 64.546485] Enabling SG bit for the vap ath3 features 4000 [ 64.546485] Enabling TSO bit for the vap ath3 features 4000 [ 64.546485] Enabling LRO bit for the vap ath3 features 4000 [ 64.546797] VAP device ath3 created osifp: (d6386480) os_if: (d6394000) [ 64.555545] siwfreq [ 64.555545] Set freq vap 3 stop send + d699c000 [ 64.555701] Set freq vap 3 stop send -d699c000 [ 64.581380] Set wait done --d699c000 [ 64.581412] Set freq vap 3 stop send + d83a0000 [ 64.581537] Set freq vap 3 stop send -d83a0000 [ 64.611371] Set wait done --d83a0000 [ 64.611402] Set freq vap 3 stop send + d7560000 [ 64.611496] Set freq vap 3 stop send -d7560000 [ 64.641393] Set wait done --d7560000 [ 64.641393] Set freq vap 3 stop send + d6394000 [ 64.641518] Set freq vap 3 stop send -d6394000 [ 64.671102] Set wait done --d6394000 [ 64.692721] ME Pool succesfully initialized vaddr - d6580000 paddr - 0 [ 64.692721] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 64.692783] ME Pool succesfully initialized vaddr - d65c0000 paddr - 0 [ 64.692814] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 64.692845] ME Pool succesfully initialized vaddr - d6600000 paddr - 0 [ 64.692845] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 64.692939] ME Pool succesfully initialized vaddr - d6640000 paddr - 0 [ 64.692939] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 64.693002] ME Pool succesfully initialized vaddr - d6680000 paddr - 0 [ 64.693033] num_elems = 1500 buf_size - 64 pool_size = 102000 [ 64.693095] Enable MCAST_TO_UCAST [ 64.922368] mc_netlink_receive: Disable bridge snooping! [ 65.092408] 8021q: adding VLAN 0 to HW filter on device ath0 [ 65.093002] device ath0 entered promiscuous mode [ 65.093064] br-lan: port 2(ath0) entered forwarding state [ 65.093095] br-lan: port 2(ath0) entered forwarding state [ 65.390159] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [ 65.421587] br-lan: port 2(ath0) entered disabled state [ 65.444048] [wifi0] FWLOG: [66755] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 65.460637] DEVICE IS DOWN ifname=ath0 [ 65.460887] DEVICE IS DOWN ifname=ath0 [ 65.503811] [ 65.503811] DES SSID SET=ZyXELXXXXX6.speed [ 65.531865] Scan in progress.. Cancelling it [ 65.561574] br-lan: port 2(ath0) entered forwarding state [ 65.561605] br-lan: port 2(ath0) entered forwarding state [ 65.561824] 8021q: adding VLAN 0 to HW filter on device ath0 [ 65.574414] Scan in progress.. Cancelling it [ 65.601780] br-lan: port 2(ath0) entered disabled state [ 65.604904] 8021q: adding VLAN 0 to HW filter on device ath1 [ 65.607185] Scan in progress.. Cancelling it [ 65.607685] wmi_unified_vdev_down_send for vap 1 (d8420000) [ 65.634989] 8021q: adding VLAN 0 to HW filter on device ath2 [ 65.637363] Scan in progress.. Cancelling it [ 65.637738] wmi_unified_vdev_down_send for vap 2 (d8420000) [ 65.665042] 8021q: adding VLAN 0 to HW filter on device ath3 [ 65.667447] Scan in progress.. Cancelling it [ 65.667822] wmi_unified_vdev_down_send for vap 3 (d8420000) [ 65.721993] br-lan: port 2(ath0) entered forwarding state [ 65.722024] br-lan: port 2(ath0) entered forwarding state [ 65.722336] 8021q: adding VLAN 0 to HW filter on device ath0 [ 66.444173] [wifi0] FWLOG: [66868] WAL_DBGID_SECURITY_ENCR_EN ( ) [ 66.444204] [wifi0] FWLOG: [66868] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) [ 66.444204] [wifi0] FWLOG: [66946] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 66.444204] [wifi0] FWLOG: [66946] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 66.444236] [wifi0] FWLOG: [66977] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 66.444236] [wifi0] FWLOG: [66977] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 66.444267] [wifi0] FWLOG: [67008] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 66.444267] [wifi0] FWLOG: [67008] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 66.444267] [wifi0] FWLOG: [67377] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 66.444298] [wifi0] FWLOG: [67692] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 67.444579] [wifi0] FWLOG: [68006] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 67.444579] [wifi0] FWLOG: [68320] WAL channel change freq=5260, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 67.444611] [wifi0] FWLOG: [68633] WAL channel change freq=5280, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 67.720337] br-lan: port 2(ath0) entered forwarding state [ 68.444736] [wifi0] FWLOG: [68948] WAL channel change freq=5300, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 68.444767] [wifi0] FWLOG: [69262] WAL channel change freq=5320, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 68.444767] [wifi0] FWLOG: [69575] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 69.444892] [wifi0] FWLOG: [69889] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 69.444892] [wifi0] FWLOG: [70204] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 69.444923] [wifi0] FWLOG: [70518] WAL channel change freq=5560, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 69.444923] [wifi0] FWLOG: [70832] WAL channel change freq=5580, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 70.445079] [wifi0] FWLOG: [71146] WAL channel change freq=5600, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 70.445110] [wifi0] FWLOG: [71459] WAL channel change freq=5620, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 70.445110] [wifi0] FWLOG: [71774] WAL channel change freq=5640, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 71.445485] [wifi0] FWLOG: [72088] WAL channel change freq=5660, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 71.445517] [wifi0] FWLOG: [72402] WAL channel change freq=5680, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 71.445517] [wifi0] FWLOG: [72716] WAL channel change freq=5700, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 71.548984] wmi_unified_vdev_down_send for vap 0 (d8420000) [ 71.549140] OL vap_start + [ 71.549140] wmi_unified_vdev_start_send for vap 0 (d8420000) [ 71.549172] OL vap_start - [ 71.549172] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 [ 71.898844] ol_vdev_start_resp_ev for vap 0 (d8420000) [ 71.898844] ol_ath_vap_join: join operation is only for STA/IBSS mode [ 71.898875] ol_ath_wmm_update: [ 71.898875] ol_if_dfs_configure: called [ 71.898875] ol_if_dfs_configure: ETSI domain [ 71.898906] ol_if_dfs_disable: called [ 71.898937] ol_if_dfs_enable: called [ 71.899000] ieee80211_dfs_send_dfs_wait[307] VAP chan mismatch vap 5180 ic 5500 [ 71.899000] ieee80211_dfs_send_dfs_wait[307] VAP chan mismatch vap 5180 ic 5500 [ 71.899000] ieee80211_dfs_send_dfs_wait[307] VAP chan mismatch vap 5180 ic 5500 [ 71.899000] cac_start chan 100 timeout 62 sec, curr time: 4294739 sec [ 72.445923] [wifi0] FWLOG: [73029] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 72.445954] [wifi0] FWLOG: [73029] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 72.445954] [wifi0] FWLOG: [73030] vap-0 VDEV_MGR_VDEV_START ( 0x157c, 0x2, 0x0, 0x1 ) [ 72.445985] [wifi0] FWLOG: [73030] WAL channel change freq=5500, mode=10 flags=0 rx_ok=1 tx_ok=1 [ 75.460262] mc_netlink_receive: Enable bridge snooping! [ 76.008091] isCountryCodeValid: EEPROM regdomain 0x0 [ 76.008122] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 76.008122] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 76.008153] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 76.008153] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 76.008153] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 76.008153] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 76.008184] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 76.008184] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 76.008184] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 76.008184] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 76.008184] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 76.008216] ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 [ 76.008216] ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 [ 76.015057] ath_ioctl: SIOC80211IFCREATE CALLED [ 76.015089] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 60:31:97:XX:XX:X4: [ 76.015432] Setting dscp for pdev [ 76.015526] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 76.015526] Enabling TX checksum bit for the vap ath10 features 4000 [ 76.015526] Enabling SG bit for the vap ath10 features 4000 [ 76.015620] Enabling SG bit for the vap ath10 features 4000 [ 76.015620] Enabling TSO bit for the vap ath10 features 4000 [ 76.015620] Enabling LRO bit for the vap ath10 features 4000 [ 76.015901] VAP device ath10 created osifp: (d63b8480) os_if: (d63d8000) [ 76.023805] siwfreq [ 76.023836] Set freq vap 0 stop send + d63d8000 [ 76.023930] Set freq vap 0 stop send -d63d8000 [ 76.051077] Set wait done --d63d8000 [ 76.058544] ath_ioctl: SIOC80211IFCREATE CALLED [ 76.058575] wmi_unified_vdev_create_send: ID = 1 Type = 1, Subtype = 0 VAP Addr = 66:31:97:XX:XX:X4: [ 76.059106] Setting dscp for pdev [ 76.059200] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 76.059231] Enabling TX checksum bit for the vap ath11 features 4000 [ 76.059231] Enabling SG bit for the vap ath11 features 4000 [ 76.059231] Enabling SG bit for the vap ath11 features 4000 [ 76.059231] Enabling TSO bit for the vap ath11 features 4000 [ 76.059231] Enabling LRO bit for the vap ath11 features 4000 [ 76.059575] VAP device ath11 created osifp: (d66b9480) os_if: (d63a4000) [ 76.066572] siwfreq [ 76.066604] Set freq vap 1 stop send + d63d8000 [ 76.066697] Set freq vap 1 stop send -d63d8000 [ 76.091096] Set wait done --d63d8000 [ 76.091127] Set freq vap 1 stop send + d63a4000 [ 76.091190] Set freq vap 1 stop send -d63a4000 [ 76.121118] Set wait done --d63a4000 [ 76.126210] ath_ioctl: SIOC80211IFCREATE CALLED [ 76.126241] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 6a:31:97:XX:XX:X4: [ 76.126741] Setting dscp for pdev [ 76.126804] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 76.126804] Enabling TX checksum bit for the vap ath12 features 4000 [ 76.126804] Enabling SG bit for the vap ath12 features 4000 [ 76.126835] Enabling SG bit for the vap ath12 features 4000 [ 76.126835] Enabling TSO bit for the vap ath12 features 4000 [ 76.126835] Enabling LRO bit for the vap ath12 features 4000 [ 76.127303] VAP device ath12 created osifp: (d66bbc80) os_if: (d66cc000) [ 76.135301] siwfreq [ 76.135301] Set freq vap 2 stop send + d63d8000 [ 76.135488] Set freq vap 2 stop send -d63d8000 [ 76.161387] Set wait done --d63d8000 [ 76.161387] Set freq vap 2 stop send + d63a4000 [ 76.161543] Set freq vap 2 stop send -d63a4000 [ 76.191346] Set wait done --d63a4000 [ 76.191377] Set freq vap 2 stop send + d66cc000 [ 76.191471] Set freq vap 2 stop send -d66cc000 [ 76.221368] Set wait done --d66cc000 [ 76.226522] ath_ioctl: SIOC80211IFCREATE CALLED [ 76.226554] wmi_unified_vdev_create_send: ID = 3 Type = 1, Subtype = 0 VAP Addr = 6e:31:97:XX:XX:X4: [ 76.226897] Setting dscp for pdev [ 76.226960] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 76.226991] Enabling TX checksum bit for the vap ath13 features 4000 [ 76.226991] Enabling SG bit for the vap ath13 features 4000 [ 76.226991] Enabling SG bit for the vap ath13 features 4000 [ 76.226991] Enabling TSO bit for the vap ath13 features 4000 [ 76.226991] Enabling LRO bit for the vap ath13 features 4000 [ 76.227366] VAP device ath13 created osifp: (d66bfc80) os_if: (d66c0000) [ 76.234895] siwfreq [ 76.234926] Set freq vap 3 stop send + d63d8000 [ 76.235082] Set freq vap 3 stop send -d63d8000 [ 76.261387] Set wait done --d63d8000 [ 76.261387] Set freq vap 3 stop send + d63a4000 [ 76.261574] Set freq vap 3 stop send -d63a4000 [ 76.291346] Set wait done --d63a4000 [ 76.291377] Set freq vap 3 stop send + d66cc000 [ 76.291502] Set freq vap 3 stop send -d66cc000 [ 76.321337] Set wait done --d66cc000 [ 76.321368] Set freq vap 3 stop send + d66c0000 [ 76.321462] Set freq vap 3 stop send -d66c0000 [ 76.351358] Set wait done --d66c0000 [ 76.372696] ME Pool succesfully initialized vaddr - d6140000 paddr - 0 [ 76.372727] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 76.372789] ME Pool succesfully initialized vaddr - d6180000 paddr - 0 [ 76.372789] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 76.372852] ME Pool succesfully initialized vaddr - d61c0000 paddr - 0 [ 76.372852] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 76.372914] ME Pool succesfully initialized vaddr - d6200000 paddr - 0 [ 76.372914] num_elems = 2500 buf_size - 64 pool_size = 170000 [ 76.372977] ME Pool succesfully initialized vaddr - d6120000 paddr - 0 [ 76.372977] num_elems = 1500 buf_size - 64 pool_size = 102000 [ 76.373008] Enable MCAST_TO_UCAST [ 76.714870] 8021q: adding VLAN 0 to HW filter on device ath10 [ 76.715495] device ath10 entered promiscuous mode [ 76.715588] br-lan: port 3(ath10) entered forwarding state [ 76.715620] br-lan: port 3(ath10) entered forwarding state [ 76.860387] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [ 76.892033] br-lan: port 3(ath10) entered disabled state [ 76.930365] DEVICE IS DOWN ifname=ath10 [ 76.930459] DEVICE IS DOWN ifname=ath10 [ 76.976632] [ 76.976632] DES SSID SET=ZyXELXXXXX6 [ 77.040393] Scan in progress.. Cancelling it [ 77.071258] br-lan: port 3(ath10) entered forwarding state [ 77.071290] br-lan: port 3(ath10) entered forwarding state [ 77.071415] 8021q: adding VLAN 0 to HW filter on device ath10 [ 77.751765] [wifi1] FWLOG: [78463] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 77.751796] [wifi1] FWLOG: [78615] WAL_DBGID_SECURITY_ENCR_EN ( ) [ 77.751796] [wifi1] FWLOG: [78615] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) [ 77.751796] [wifi1] FWLOG: [78777] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 77.751827] [wifi1] FWLOG: [79092] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 78.075507] mc_netlink_receive: Disable bridge snooping! [ 78.388597] mc_netlink_receive: Enable bridge snooping! [ 78.446454] Scan in progress.. Cancelling it [ 78.471540] br-lan: port 3(ath10) entered disabled state [ 78.474789] 8021q: adding VLAN 0 to HW filter on device ath11 [ 78.477288] Scan in progress.. Cancelling it [ 78.477850] wmi_unified_vdev_down_send for vap 1 (d7570000) [ 78.504967] 8021q: adding VLAN 0 to HW filter on device ath12 [ 78.507466] Scan in progress.. Cancelling it [ 78.523992] wmi_unified_vdev_down_send for vap 2 (d7570000) [ 78.540362] 8021q: adding VLAN 0 to HW filter on device ath13 [ 78.542861] Scan in progress.. Cancelling it [ 78.543298] wmi_unified_vdev_down_send for vap 3 (d7570000) [ 78.602124] br-lan: port 3(ath10) entered forwarding state [ 78.602186] br-lan: port 3(ath10) entered forwarding state [ 78.602624] 8021q: adding VLAN 0 to HW filter on device ath10 [ 78.751921] [wifi1] FWLOG: [79406] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 78.751952] [wifi1] FWLOG: [79719] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 78.751952] [wifi1] FWLOG: [80033] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 78.751952] [wifi1] FWLOG: [80087] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 78.751983] [wifi1] FWLOG: [80087] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 78.751983] [wifi1] FWLOG: [80112] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 78.752014] [wifi1] FWLOG: [80135] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 78.752014] [wifi1] FWLOG: [80135] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 78.752046] [wifi1] FWLOG: [80154] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 78.752046] [wifi1] FWLOG: [80154] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 79.752046] [wifi1] FWLOG: [80528] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 79.752077] [wifi1] FWLOG: [80843] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 79.752077] [wifi1] FWLOG: [81157] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 80.600218] br-lan: port 3(ath10) entered forwarding state [ 80.770634] [wifi1] FWLOG: [81470] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 80.770634] [wifi1] FWLOG: [81785] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 80.770665] [wifi1] FWLOG: [82098] WAL channel change freq=2442, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 80.770665] [wifi1] FWLOG: [82412] WAL channel change freq=2447, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 81.770790] [wifi1] FWLOG: [82726] WAL channel change freq=2452, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 81.770790] [wifi1] FWLOG: [83040] WAL channel change freq=2457, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 81.770821] [wifi1] FWLOG: [83354] WAL channel change freq=2462, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 82.587628] wmi_unified_vdev_down_send for vap 0 (d7570000) [ 82.587753] mlme_create_infra_bss : Overriding HT40 channel with HT20 channel [ 82.587753] OL vap_start + [ 82.587785] wmi_unified_vdev_start_send for vap 0 (d7570000) [ 82.587785] OL vap_start - [ 82.587816] ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 [ 83.017025] [wifi1] FWLOG: [83668] WAL channel change freq=2467, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 83.017119] ol_vdev_start_resp_ev for vap 0 (d7570000) [ 83.017119] ol_ath_vap_join: join operation is only for STA/IBSS mode [ 83.017119] ol_ath_wmm_update: [ 83.017244] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 [ 83.017244] wmi_unified_vdev_up_send for vap 0 (d7570000) [ 83.017275] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 83.017338] [wifi1] FWLOG: [83982] WAL channel change freq=2472, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 83.017400] [wifi1] FWLOG: [84295] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 83.017400] [wifi1] FWLOG: [84295] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 83.017400] [wifi1] FWLOG: [84296] vap-0 VDEV_MGR_VDEV_START ( 0x99e, 0x2, 0x0, 0x0 ) [ 83.017494] [wifi1] FWLOG: [84296] WAL channel change freq=2462, mode=5 flags=0 rx_ok=1 tx_ok=1 [ 84.017244] [wifi1] FWLOG: [84735] VDEV_MGR_HP_START_TIME ( 0x0, 0x99e, 0x1531000 ) [ 84.017275] [wifi1] FWLOG: [84735] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 ) [ 84.017307] [wifi1] FWLOG: [84735] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 84.017307] [wifi1] FWLOG: [84735] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x99e, 0x0, 0x0 ) [ 109.888847] Enabling NSS RPS [ 110.406060] mc_attach: bridge br-lan is already attached [ 110.406060] mc_netlink_receive: Enable bridge snooping! [ 126.545517] ECM exit [ 126.760543] ECM exit complete [ 126.866010] ECM init [ 126.866541] ECM init complete [ 133.403592] msm_thermal: Max frequency reset for cpu0 [ 133.403592] msm_thermal: Max frequency reset for cpu1 [ 133.403623] msm_thermal: enabled = 0 [ 133.650265] ECM exit [ 133.930146] cac_timeout cac expired, chan 5500 curr time 4294801 [ 133.930240] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 [ 133.930271] wmi_unified_vdev_up_send for vap 0 (d8420000) [ 133.930303] __ieee80211_smart_ant_init: Smart Antenna is not supported [ 134.120274] ECM exit complete [ 134.221618] ECM init [ 134.222180] ECM init complete [ 134.464323] [wifi0] FWLOG: [136901] VDEV_MGR_HP_START_TIME ( 0x0, 0x157c, 0x4bc8000 ) [ 134.464386] [wifi0] FWLOG: [136901] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 ) [ 134.464386] [wifi0] FWLOG: [136901] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [ 134.467541] [wifi0] FWLOG: [136901] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x157c, 0x0, 0x0 ) [ 272.436176] ECM exit [ 272.680662] ECM exit complete [ 272.836269] ECM init [ 272.837425] ECM init complete root@NBG6817:~#


OpenWrt bootlog

root@nbg6817:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.67 (XXX@XXX) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7984-555c592304)) #0 SMP Thu Aug 30 13:19:45 2018 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NBG6817 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 122880 [ 0.000000] free_area_init_node: node 0, pgdat c0b26e80, node_mem_map ddc39000 [ 0.000000] Normal zone: 960 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 122880 pages, LIFO batch:31 [ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x408 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu @ddc03000 s29836 r8192 d23412 u61440 [ 0.000000] pcpu-alloc: s29836 r8192 d23412 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p8 [ 0.000000] Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p8 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 478372K/491520K available (4796K kernel code, 157K rwdata, 1268K rodata, 1024K init, 273K bss, 13148K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc07af038 (5789 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b27780 ( 158 kB) [ 0.000000] .bss : 0xc0b29000 - 0xc0b6d774 ( 274 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000022] Switching to timer-based delay loop, resolution 160ns [ 0.000208] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=6250) [ 0.000231] pid_max: default: 32768 minimum: 301 [ 0.000355] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000372] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000865] CPU: Testing write buffer coherency: ok [ 0.001732] Setting up static identity map for 0x42300000 - 0x42300060 [ 0.001886] Hierarchical SRCU implementation. [ 0.002700] smp: Bringing up secondary CPUs ... [ 0.004584] smp: Brought up 1 node, 2 CPUs [ 0.004599] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.004610] CPU: All CPU(s) started in SVC mode. [ 0.015383] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.015540] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.015564] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.015675] pinctrl core: initialized pinctrl subsystem [ 0.016732] NET: Registered protocol family 16 [ 0.017096] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018524] cpuidle: using governor ladder [ 0.018587] cpuidle: using governor menu [ 0.041699] msm_bus_fabric_init_driver [ 0.043156] usbcore: registered new interface driver usbfs [ 0.043238] usbcore: registered new interface driver hub [ 0.043323] usbcore: registered new device driver usb [ 0.043386] pps_core: LinuxPPS API ver. 1 registered [ 0.043397] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.043427] PTP clock support registered [ 0.045346] clocksource: Switched to clocksource dg_timer [ 0.049136] NET: Registered protocol family 2 [ 0.049854] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.049893] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.049947] TCP: Hash tables configured (established 4096 bind 4096) [ 0.050040] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.050066] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.050256] NET: Registered protocol family 1 [ 0.050302] PCI: CLS 0 bytes, default 64 [ 0.051690] No memory allocated for crashlog [ 0.051938] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.057340] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.057358] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.067048] io scheduler noop registered [ 0.067066] io scheduler deadline registered (default) [ 0.068689] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator [ 0.068791] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.068887] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.069752] OF: PCI: host bridge /soc/pci@1b500000 ranges: [ 0.069793] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.069817] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.179025] qcom-pcie 1b500000.pci: link up [ 0.179194] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.179215] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.179235] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.179251] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.179267] pci_bus 0000:00: scanning bus [ 0.179316] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.179409] pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x44 [ 0.179607] pci 0000:00:00.0: supports D1 [ 0.179618] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.179634] pci 0000:00:00.0: PME# disabled [ 0.179894] pci_bus 0000:00: fixups for bus [ 0.179917] PCI: bus0: Fast back to back transfers disabled [ 0.179937] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.180059] pci_bus 0000:01: scanning bus [ 0.180236] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.180674] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.181145] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x44 [ 0.181876] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.181918] pci 0000:01:00.0: PME# disabled [ 0.182235] pci_bus 0000:01: fixups for bus [ 0.182305] PCI: bus1: Fast back to back transfers disabled [ 0.182320] pci_bus 0000:01: bus scan returning with max=01 [ 0.182337] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.182353] pci_bus 0000:00: bus scan returning with max=ff [ 0.182402] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.182424] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.182646] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.182671] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.182710] pci 0000:00:00.0: calling qcom_pcie_fixup_final+0x0/0x94 [ 0.182902] pcieport 0000:00:00.0: assign IRQ: got 67 [ 0.183205] pcieport 0000:00:00.0: AER enabled with IRQ 35 [ 0.183319] pci 0000:01:00.0: calling qcom_pcie_fixup_final+0x0/0x94 [ 0.183827] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator [ 0.183937] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.184028] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.184870] OF: PCI: host bridge /soc/pci@1b700000 ranges: [ 0.184909] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.184932] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.294892] qcom-pcie 1b700000.pci: link up [ 0.295049] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.295067] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.295081] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.295094] pci_bus 0001:00: scanning bus [ 0.295134] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.295210] pci 0001:00:00.0: calling pci_fixup_ide_bases+0x0/0x44 [ 0.295271] pci 0001:00:00.0: supports D1 [ 0.295280] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.295292] pci 0001:00:00.0: PME# disabled [ 0.295608] pci_bus 0001:00: fixups for bus [ 0.295628] PCI: bus0: Fast back to back transfers disabled [ 0.295644] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.295766] pci_bus 0001:01: scanning bus [ 0.295953] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.296325] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.296924] pci 0001:01:00.0: calling pci_fixup_ide_bases+0x0/0x44 [ 0.297703] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.297748] pci 0001:01:00.0: PME# disabled [ 0.298080] pci_bus 0001:01: fixups for bus [ 0.298155] PCI: bus1: Fast back to back transfers disabled [ 0.298168] pci_bus 0001:01: bus scan returning with max=01 [ 0.298184] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.298200] pci_bus 0001:00: bus scan returning with max=ff [ 0.298237] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.298258] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.298389] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.298409] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.298440] pci 0001:00:00.0: calling qcom_pcie_fixup_final+0x0/0x94 [ 0.298698] pcieport 0001:00:00.0: assign IRQ: got 100 [ 0.298990] pcieport 0001:00:00.0: AER enabled with IRQ 68 [ 0.299102] pci 0001:01:00.0: calling qcom_pcie_fixup_final+0x0/0x94 [ 0.301388] L2 @ QSB rate. Forcing new rate. [ 0.301665] L2 @ 384000 KHz [ 0.301837] CPU0 @ 800000 KHz [ 0.301850] CPU1 @ QSB rate. Forcing new rate. [ 0.301965] CPU1 @ 384000 KHz [ 0.306098] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.307677] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0 [ 0.309157] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.310039] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.310132] msm_serial 16340000.serial: uartclk = 7372800 [ 0.310209] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 101, base_baud = 460800) is a MSM [ 0.310244] msm_serial: console setup on port #0 [ 1.058639] console [ttyMSM0] enabled [ 1.063395] msm_serial: driver initialized [ 1.072656] loop: module loaded [ 1.074136] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 1.076297] m25p80 spi0.0: mx25u3235f (4096 Kbytes) [ 1.082046] 13 qcom-smem partitions found on MTD device spi0.0 [ 1.086668] Creating 13 MTD partitions on "spi0.0": [ 1.092578] 0x000000000000-0x000000020000 : "0:SBL1" [ 1.098269] 0x000000020000-0x000000040000 : "0:MIBIB" [ 1.103306] 0x000000040000-0x000000060000 : "0:SBL2" [ 1.108240] 0x000000060000-0x0000000a0000 : "0:SBL3" [ 1.113263] 0x0000000a0000-0x0000000b0000 : "0:DDRCONFIG" [ 1.118231] 0x0000000b0000-0x0000000c0000 : "0:SSD" [ 1.123610] 0x0000000c0000-0x000000100000 : "0:TZ" [ 1.128223] 0x000000100000-0x000000140000 : "0:RPM" [ 1.133126] 0x000000140000-0x0000001c0000 : "0:APPSBL" [ 1.137930] 0x0000001c0000-0x0000001d0000 : "0:APPSBLENV" [ 1.143115] 0x0000001d0000-0x0000001e0000 : "0:ART" [ 1.148580] 0x0000001e0000-0x0000001f0000 : "0:DUAL_FLAG" [ 1.153184] 0x0000001f0000-0x000000400000 : "0:RESERVED" [ 1.159818] libphy: GPIO Bitbanged MDIO: probed [ 1.166514] NOHZ: local_softirq_pending 202 [ 1.167583] NOHZ: local_softirq_pending 282 [ 1.171820] NOHZ: local_softirq_pending 282 [ 1.175975] NOHZ: local_softirq_pending 282 [ 1.180160] NOHZ: local_softirq_pending 282 [ 1.184315] NOHZ: local_softirq_pending 282 [ 1.185238] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 1.192656] NOHZ: local_softirq_pending 282 [ 1.199247] NOHZ: local_softirq_pending 282 [ 1.203340] NOHZ: local_softirq_pending 282 [ 1.207495] NOHZ: local_softirq_pending 282 [ 1.996619] libphy: Fixed MDIO Bus: probed [ 1.998228] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock [ 2.000009] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.006194] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled [ 2.011227] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported [ 2.017308] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors [ 2.025306] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors [ 2.032835] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported [ 2.039896] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2 [ 2.047766] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported [ 2.053609] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported [ 2.060985] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.069362] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 2.076612] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.082662] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 2.087722] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 2.093782] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 2.101780] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 2.109309] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 2.116370] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 2.124243] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 2.130083] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 2.137456] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.144943] i2c /dev entries driver [ 2.153661] Calibration not found. [ 2.156014] qcom-tsens 900000.thermal-sensor: tsens calibration failed [ 2.160689] Speed bin: 0 [ 2.166012] PVS bin: 5 [ 2.170034] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.170946] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.179079] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 34,0 (pio) [ 2.185624] mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2 [ 2.217924] sdhci: Secure Digital Host Controller Interface driver [ 2.217955] sdhci: Copyright(c) Pierre Ossman [ 2.223086] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.229298] NET: Registered protocol family 10 [ 2.235047] Segment Routing with IPv6 [ 2.237563] NET: Registered protocol family 17 [ 2.241851] 8021q: 802.1Q VLAN Support v1.8 [ 2.245665] Registering SWP/SWPB emulation handler [ 2.263155] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364 [ 2.278833] s1a: supplied by regulator-dummy [ 2.278931] s1a: Bringing 0uV into 1050000-1050000uV [ 2.282580] s1b: supplied by regulator-dummy [ 2.287242] s1b: Bringing 0uV into 1050000-1050000uV [ 2.291719] s2a: supplied by regulator-dummy [ 2.296458] s2a: Bringing 0uV into 775000-775000uV [ 2.300905] s2b: supplied by regulator-dummy [ 2.305296] s2b: Bringing 0uV into 775000-775000uV [ 2.314112] hctosys: unable to open rtc device (rtc0) [ 2.315192] Waiting for root device /dev/mmcblk0p8... [ 2.356948] mmc0: new high speed MMC card at address 0001 [ 2.357768] mmcblk0: mmc0:0001 S10004 3.56 GiB [ 2.361735] mmcblk0boot0: mmc0:0001 S10004 partition 1 4.00 MiB [ 2.365888] mmcblk0boot1: mmc0:0001 S10004 partition 2 4.00 MiB [ 2.371889] mmcblk0rpmb: mmc0:0001 S10004 partition 3 4.00 MiB [ 2.380034] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 [ 2.397276] VFS: Mounted root (squashfs filesystem) readonly on device 179:8. [ 2.399004] Freeing unused kernel memory: 1024K [ 2.755184] init: Console is alive [ 2.755298] init: - watchdog - [ 2.863812] random: fast init done [ 3.505493] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.560129] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.562144] SCSI subsystem initialized [ 3.568030] libata version 3.00 loaded. [ 3.570969] ehci-platform: EHCI generic platform driver [ 3.573382] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.575535] ohci-platform: OHCI generic platform driver [ 3.688191] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.688249] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.692865] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010 [ 3.700265] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x11000000 [ 3.709827] hub 1-0:1.0: USB hub found [ 3.715230] hub 1-0:1.0: 1 port detected [ 3.719017] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.722784] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.728082] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.735782] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.742877] hub 2-0:1.0: USB hub found [ 3.750619] hub 2-0:1.0: 1 port detected [ 3.754580] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.758201] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.763670] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010 [ 3.771107] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x10000000 [ 3.780381] hub 3-0:1.0: USB hub found [ 3.786026] hub 3-0:1.0: 1 port detected [ 3.789830] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.793625] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 3.798915] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.806593] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.813718] hub 4-0:1.0: USB hub found [ 3.821488] hub 4-0:1.0: 1 port detected [ 3.828826] usbcore: registered new interface driver usb-storage [ 3.829836] usbcore: registered new interface driver uas [ 3.835209] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.848388] init: - preinit - [ 4.208418] random: jshn: uninitialized urandom read (4 bytes read) [ 4.276718] random: jshn: uninitialized urandom read (4 bytes read) [ 4.557348] random: jshn: uninitialized urandom read (4 bytes read) [ 5.745044] ipq806x-gmac-dwmac 37400000.ethernet eth1: device MAC address 66:8a:af:XX:XX:Xe [ 5.745212] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL) [ 5.753340] dwmac1000: Master AXI performs any burst length [ 5.762372] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 5.767854] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 5.777311] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 5.780599] urandom_read: 2 callbacks suppressed [ 5.780604] random: procd: uninitialized urandom read (4 bytes read) [ 6.822138] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 6.822218] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 11.974183] mount_root: loading kmods from internal overlay [ 12.006160] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 12.009402] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 12.643615] random: crng init done [ 14.681271] block: attempting to load /etc/config/fstab [ 14.683167] block: unable to load configuration (fstab: Entry not found) [ 14.685402] block: no usable configuration [ 14.776332] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 17.276122] block: attempting to load /etc/config/fstab [ 17.276207] block: unable to load configuration (fstab: Entry not found) [ 17.280280] block: no usable configuration [ 17.288616] mount_root: overlay filesystem has not been fully initialized yet [ 17.294867] mount_root: switching to ext4 overlay [ 17.392234] urandom-seed: Seed file not found (/etc/urandom.seed) [ 17.459779] procd: - early - [ 17.459882] procd: - watchdog - [ 18.037220] procd: - watchdog - [ 18.037557] procd: - ubus - [ 18.101900] procd: - init - [ 18.519555] kmodloader: loading kernel modules from /etc/modules.d/* [ 18.565967] Initializing XFRM netlink socket [ 18.567550] NET: Registered protocol family 15 [ 18.584233] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 18.590397] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 18.637986] Netfilter messages via NETLINK v0.30. [ 18.640093] ip_set: protocol 6 [ 18.668802] u32 classifier [ 18.668823] input device check on [ 18.670465] Actions configured [ 18.675789] Mirror/redirect action on [ 18.685419] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 18.690564] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180 [ 18.690595] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d [ 18.700582] ip_tables: (C) 2000-2006 Netfilter Core Team [ 18.757694] ctnetlink v0.93: registering with nfnetlink. [ 18.816337] usbcore: registered new interface driver usblp [ 18.830828] xt_time: kernel timezone is -0000 [ 18.902911] PPP generic driver version 2.4.2 [ 18.904144] NET: Registered protocol family 24 [ 18.917229] ath10k_pci 0000:01:00.0: assign IRQ: got 67 [ 18.917914] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 18.918005] ath10k_pci 0000:01:00.0: enabling bus mastering [ 18.918630] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 19.022318] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2 [ 19.022348] ath10k_pci 0000:01:00.0: Falling back to user helper [ 19.429216] print_req_error: I/O error, dev loop0, sector 578 [ 19.772664] print_req_error: I/O error, dev loop0, sector 1012 [ 20.092695] print_req_error: I/O error, dev loop0, sector 1474 [ 20.412642] print_req_error: I/O error, dev loop0, sector 1936 [ 20.732615] print_req_error: I/O error, dev loop0, sector 2398 [ 21.045603] print_req_error: I/O error, dev loop0, sector 2860 [ 21.365640] print_req_error: I/O error, dev loop0, sector 3322 [ 21.684729] print_req_error: I/O error, dev loop0, sector 3784 [ 25.288990] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 25.510089] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 25.510121] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 25.521068] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.6-00144 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 e385d6b0 [ 27.791597] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 dd6d039c [ 33.710184] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1 [ 33.771329] ath: EEPROM regdomain: 0x0 [ 33.771342] ath: EEPROM indicates default country code should be used [ 33.771352] ath: doing EEPROM country->regdmn map search [ 33.771369] ath: country maps to regdmn code: 0x3a [ 33.771382] ath: Country alpha2 being used: US [ 33.771393] ath: Regpair used: 0x3a [ 33.776980] ath10k_pci 0001:01:00.0: assign IRQ: got 100 [ 33.777875] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 33.777988] ath10k_pci 0001:01:00.0: enabling bus mastering [ 33.778668] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 33.882674] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2 [ 33.882709] ath10k_pci 0001:01:00.0: Falling back to user helper [ 34.360308] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 34.360583] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 34.368305] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 34.380900] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.6-00144 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 e385d6b0 [ 36.652237] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 dd6d039c [ 42.563596] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1 [ 42.625912] ath: EEPROM regdomain: 0x0 [ 42.625925] ath: EEPROM indicates default country code should be used [ 42.625934] ath: doing EEPROM country->regdmn map search [ 42.625952] ath: country maps to regdmn code: 0x3a [ 42.625964] ath: Country alpha2 being used: US [ 42.625974] ath: Regpair used: 0x3a [ 42.635813] kmodloader: done loading kernel modules from /etc/modules.d/* [ 52.350644] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL) [ 52.351744] dwmac1000: Master AXI performs any burst length [ 52.359645] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 52.365136] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 52.374188] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 52.420206] br-lan: port 1(eth1.1) entered blocking state [ 52.420238] br-lan: port 1(eth1.1) entered disabled state [ 52.425019] device eth1.1 entered promiscuous mode [ 52.430046] device eth1 entered promiscuous mode [ 52.455835] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 52.484049] ipq806x-gmac-dwmac 37200000.ethernet eth0: device MAC address 56:06:1d:XX:XX:X4 [ 52.484282] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL) [ 52.492383] dwmac1000: Master AXI performs any burst length [ 52.501389] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 52.506887] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 52.516384] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 52.591797] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready [ 53.412559] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 53.414924] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 53.424046] br-lan: port 1(eth1.1) entered blocking state [ 53.426569] br-lan: port 1(eth1.1) entered forwarding state [ 53.485209] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 53.541392] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 53.541583] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 53.557633] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready [ 53.693151] ath: EEPROM regdomain: 0x8114 [ 53.693158] ath: EEPROM indicates we should expect a country code [ 53.693162] ath: doing EEPROM country->regdmn map search [ 53.693166] ath: country maps to regdmn code: 0x37 [ 53.693170] ath: Country alpha2 being used: DE [ 53.693175] ath: Regpair used: 0x37 [ 53.693186] ath: regdomain 0x8114 dynamically updated by user [ 53.693210] ath: EEPROM regdomain: 0x8114 [ 53.693214] ath: EEPROM indicates we should expect a country code [ 53.693217] ath: doing EEPROM country->regdmn map search [ 53.693221] ath: country maps to regdmn code: 0x37 [ 53.693225] ath: Country alpha2 being used: DE [ 53.693228] ath: Regpair used: 0x37 [ 53.693235] ath: regdomain 0x8114 dynamically updated by user [ 61.868681] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 61.876117] br-lan: port 2(wlan1) entered blocking state [ 61.876141] br-lan: port 2(wlan1) entered disabled state [ 61.880876] device wlan1 entered promiscuous mode [ 61.885902] br-lan: port 2(wlan1) entered blocking state [ 61.890444] br-lan: port 2(wlan1) entered forwarding state [ 61.900688] br-lan: port 2(wlan1) entered disabled state [ 67.959191] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 67.973325] br-lan: port 3(wlan0) entered blocking state [ 67.973354] br-lan: port 3(wlan0) entered disabled state [ 67.977952] device wlan0 entered promiscuous mode [ 70.071673] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 70.071815] br-lan: port 2(wlan1) entered blocking state [ 70.077139] br-lan: port 2(wlan1) entered forwarding state [ 71.504718] br-lan: port 4(wlan1.sta1) entered blocking state [ 71.504763] br-lan: port 4(wlan1.sta1) entered disabled state [ 71.509892] device wlan1.sta1 entered promiscuous mode [ 71.517423] br-lan: port 4(wlan1.sta1) entered blocking state [ 71.520271] br-lan: port 4(wlan1.sta1) entered forwarding state [ 83.725019] pppoe-wan: renamed from ppp0 [ 132.102725] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 132.103028] br-lan: port 3(wlan0) entered blocking state [ 132.108288] br-lan: port 3(wlan0) entered forwarding state root@nbg6817:~#


Notes

Space for additional notes, links to forum threads or other resources.

Tags

How to add tags

, , , , , , , , , , , , ,
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1