Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:zyxel:nbg6503 [2015/10/18 15:22] – ↷ Links adapted because of a move operation tmomastoh:zyxel:nbg6503 [2020/09/13 20:01] – [ZyXEL NBG6503] corrected links. Tested with 19.07.3 jhench
Line 1: Line 1:
 +====== ZyXEL NBG6503 ======
  
 +[[wp>IEEE 802.11ac]]-capable device from 2013. FCC ID: I88NBG6503
 +
 +  * MediaTek MT7620A-based
 +  * includes MediaTek MT7610en
 +  * 19.07.3: mt7620a-initramfs-kernel.bin is bootable to prompt with TTL serial 57600,8,1 (3.3V)
 +  * bootable from TFTP (without flashing) with this image: [[https://downloads.openwrt.org/releases/19.07.3/targets/ramips/mt7620/openwrt-19.07.3-ramips-mt7620-rt-ac51u-initramfs-kernel.bin]]
 +  * flashing this image works, stays without overlays
 +  * from within openWRT, upgrade with the image [[https://downloads.openwrt.org/releases/19.07.3/targets/ramips/mt7620/openwrt-19.07.3-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin]] through the LuCi interface, and overlayfs will work
 +  * LuCi / WiFi seem to work
 +  * WAN does not work (DHCP client fails)
 +
 +{{media:zyxel:nbg6503_general_view.png?200}}
 +
 +Bootlog (original firmware)
 +<WRAP bootlog>
 +user@PC:~$ picocom -b 57600 /dev/ttyUSB0
 +picocom v2.2
 +
 +port is        : /dev/ttyUSB0
 +flowcontrol    : none
 +baudrate is    : 57600
 +parity is      : none
 +databits are   : 8
 +stopbits are   : 1
 +escape is      : C-a
 +local echo is  : no
 +noinit is      : no
 +noreset is     : no
 +nolock is      : no
 +send_cmd is    : sz -vv
 +receive_cmd is : rz -vv -E
 +imap is        : 
 +omap is        : 
 +emap is        : crcrlf,delbs,
 +
 +Type [C-a] [C-h] to see available commands
 +
 +Terminal ready
 +
 +
 +
 +
 +
 +U-Boot 1.1.3 (Mar 11 2013 - 11:11:53)
 +
 +Board: Ralink APSoC DRAM:  64 MB
 +relocate_code Pointer at: 83fb4000
 +enable ephy clock...done. rf reg 29 = 5
 +SSC disabled.
 +******************************
 +Software System Reset Occurred
 +******************************
 +spi_wait_nsec: 29 
 +spi device id: ef 40 17 0 0 (40170000)
 +find flash: W25Q64BV
 +raspi_read: from:30000 len:1000 
 +*** Warning - bad CRC, using default environment
 +
 +============================================ 
 +Ralink UBoot Version: 4.1.1.0_a2
 +-------------------------------------------- 
 +ASIC 7620_MP (Port5<->None)
 +DRAM component: 512 Mbits DDR, width 16
 +DRAM bus: 16 bit
 +Total memory: 64 MBytes
 +Flash component: SPI Flash
 +Date:Mar 11 2013  Time:11:11:53
 +============================================ 
 +icache: sets:512, ways:4, linesz:32 ,total:65536
 +dcache: sets:256, ways:4, linesz:32 ,total:32768 
 +
 + ##### The CPU freq = 580 MHZ #### 
 + estimate memory size =64 Mbytes
 +
 +Please choose the operation: 
 +   1: Load system code to SDRAM via TFTP. 
 +   2: Load system code then write to Flash via TFTP. 
 +   3: Boot system code via Flash (default).
 +   4: Entr boot command line interface.
 +   7: Load Boot Loader code then write to Flash via Serial. 
 +   9: Load Boot Loader code then write to Flash via TFTP. 
 +   a: Auto load system code then write to Flash via TFTP. 
 + 
 +   
 +3: System Boot system code via Flash.
 +## Booting image at bc050000 ...
 +raspi_read: from:50000 len:40 
 +   Image Name:   Linux Kernel Image
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    5380973 Bytes =  5.1 MB
 +   Load Address: 80000000
 +   Entry Point:  8000c310
 +raspi_read: from:50040 len:521b6d 
 +   Verifying Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 +No initrd
 +## Transferring control to Linux (at address 8000c310) ...
 +## Giving linux memsize in MB, 64
 +
 +Starting kernel ...
 +
 +
 +LINUX started...
 +
 + THIS IS ASIC
 +
 + The CPU feqenuce set to 580 MHz
 +
 + MIPS CPU sleep mode enabled.
 + PCIE: bypass PCIe DLL.
 + PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 + disable all power about PCIe
 +Zone PFN ranges:
 +  Normal   0x00000000 -> 0x00004000
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00004000
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +MTK/Ralink System Tick Counter init... cd:80397ef8, m:214748, s:32
 +Mount-cache hash table entries: 512
 +RALINK_GPIOMODE = 1a311d
 +RALINK_GPIOMODE = 18311d
 +PPLL_CFG1=0xe6c000
 +MT7620 PPLL lock
 +PPLL_DRV =0x80080504
 +PCIe reset again
 +start PCIe register access
 +RALINK_PCI_PCICFG_ADDR = 1000f0
 +
 +*************** MT7620 PCIe RC mode *************
 +bio: create slab <bio-0> at 0
 +BAR0 at slot 0 = 0
 +bus=0x0, slot = 0x0
 +res[0]->start = 0
 +res[0]->end = 0
 +res[1]->start = 20200000
 +res[1]->end = 2020ffff
 +res[2]->start = 0
 +res[2]->end = 0
 +res[3]->start = 0
 +res[3]->end = 0
 +res[4]->start = 0
 +res[4]->end = 0
 +res[5]->start = 0
 +res[5]->end = 0
 +bus=0x1, slot = 0x0
 +res[0]->start = 20000000
 +res[0]->end = 200fffff
 +res[1]->start = 0
 +res[1]->end = 0
 +res[2]->start = 0
 +res[2]->end = 0
 +res[3]->start = 0
 +res[3]->end = 0
 +res[4]->start = 0
 +res[4]->end = 0
 +res[5]->start = 0
 +res[5]->end = 0
 +bus=0x1, slot = 0x0
 +res[0]->start = 20100000
 +res[0]->end = 201fffff
 +res[1]->start = 0
 +res[1]->end = 0
 +res[2]->start = 0
 +res[2]->end = 0
 +res[3]->start = 0
 +res[3]->end = 0
 +res[4]->start = 0
 +res[4]->end = 0
 +res[5]->start = 0
 +res[5]->end = 0
 +RT3xxx EHCI/OHCI init.
 +Ralink gpio driver initialized
 +deice id : ef 40 17 0 0 (40170000)
 +W25Q64BV(ef 40170000) (8192 Kbytes)
 +mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
 +mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
 +rdm_major = 253
 +SMACCR1 -- : 0x000090ef
 +SMACCR0 -- : 0x682e40b1
 +Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
 +SMACCR1 -- : 0x000090ef
 +SMACCR0 -- : 0x682e40b1
 +nf_conntrack version 0.5.0 (888 buckets, 3552 max 400 reserved)
 +matchsize=264
 +init started: BusyBox v1.12.1 Algorithmics/MIPS FPU Emulator v1.5
 +(2014-11-25 11:16:51 CST)
 +starting pid 34, tty '': '/etc_ro/rcS'
 +mount: mounting none on /proc/bus/usb failed: No such file or directory
 +ftpalg: Waiting for message from kernel
 +starting pid 46, tty '/dev/ttyS1': '/bin/sh'
 +
 +
 +BusyBox v1.12.1 (2014-11-25 11:16:51 CST) built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +# boa: waiting for nvram_daemon 
 +@@@ BssidNum @@@
 +
 +@led=38, on=1, off=4000, blinks,=1, reset=1, time=4000
 +@@ BssidNum @@@
 +@@@  check_nvram_loadf  @@@
 +nvram flash is ok
 +rai0      no private ioctls.
 +
 +ifconfig: ioctl 0x8913 failed: No such device
 +Password for 'admin' changed
 +rmmod: ralink_wdt: No such file or directory
 +rmmod: cls: No such file or directory
 +rmmod: hw_nat: No such file or directory
 +rmmod: raeth: No such file or directory
 +insmod: bridge.ko: module not found
 +insmod: mii.ko: module not found
 +insmod: raeth.ko: module not found
 +
 +##### disable 1st wireless interface #####
 +rai0      no private ioctls.
 +
 +
 +##### disable 2nd wireless interface #####
 +rmmod: rt2860v2_ap_net: No such file or directory
 +rmmod: rt2860v2_ap: No such file or directory
 +rmmod: rt2860v2_ap_util: No such file or directory
 +rmmod: MT7610_ap: No such file or directory
 +insmod: rt_timer.ko: module not found
 +insmod: rt2860v2_ap_util.ko: module not found
 +rt2860v2_ap: module license 'unspecified' taints kernel.
 +Disabling lock debugging due to kernel taint
 +
 +
 +=== pAd = c05d0000, size = 808936 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +AP Driver version-2.7.1.6_20130807
 +insmod: rt2860v2_ap_net.ko: module not found
 +
 +
 +=== pAd = c0b02000, size = 944472 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +device_id =0x7650
 +==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
 +MACVersion = 0x76502000
 +RX DESC a23fe000  size = 2048
 +RTMP_TimerListAdd: add timer obj c0665e80!
 +RTMP_TimerListAdd: add timer obj c0631000!
 +RTMP_TimerListAdd: add timer obj c0630fd4!
 +RTMP_TimerListAdd: add timer obj c0630fa8!
 +RTMP_TimerListAdd: add timer obj c05d8070!
 +RTMP_TimerListAdd: add timer obj c05d7c64!
 +RTMP_TimerListAdd: add timer obj c05d8040!
 +RTMP_TimerListAdd: add timer obj c05d83e8!
 +RTMP_TimerListAdd: add timer obj c05d8138!
 +RTMP_TimerListAdd: add timer obj c05d8168!
 +RTMP_TimerListAdd: add timer obj c05d8328!
 +RTMP_TimerListAdd: add timer obj c05d8358!
 +RTMP_TimerListAdd: add timer obj c05db2a8!
 +RTMP_TimerListAdd: add timer obj c05dae9c!
 +RTMP_TimerListAdd: add timer obj c05db278!
 +RTMP_TimerListAdd: add timer obj c05db620!
 +RTMP_TimerListAdd: add timer obj c05db370!
 +RTMP_TimerListAdd: add timer obj c05db3a0!
 +RTMP_TimerListAdd: add timer obj c05db560!
 +RTMP_TimerListAdd: add timer obj c05db590!
 +RTMP_TimerListAdd: add timer obj c05de4e0!
 +RTMP_TimerListAdd: add timer obj c05de0d4!
 +RTMP_TimerListAdd: add timer obj c05de4b0!
 +RTMP_TimerListAdd: add timer obj c05de858!
 +RTMP_TimerListAdd: add timer obj c05de5a8!
 +RTMP_TimerListAdd: add timer obj c05de5d8!
 +RTMP_TimerListAdd: add timer obj c05de798!
 +RTMP_TimerListAdd: add timer obj c05de7c8!
 +RTMP_TimerListAdd: add timer obj c05e1718!
 +RTMP_TimerListAdd: add timer obj c05e130c!
 +RTMP_TimerListAdd: add timer obj c05e16e8!
 +RTMP_TimerListAdd: add timer obj c05e1a90!
 +RTMP_TimerListAdd: add timer obj c05e17e0!
 +RTMP_TimerListAdd: add timer obj c05e1810!
 +RTMP_TimerListAdd: add timer obj c05e19d0!
 +RTMP_TimerListAdd: add timer obj c05e1a00!
 +RTMP_TimerListAdd: add timer obj c05e4950!
 +RTMP_TimerListAdd: add timer obj c05e4544!
 +RTMP_TimerListAdd: add timer obj c05e4920!
 +RTMP_TimerListAdd: add timer obj c05e4cc8!
 +RTMP_TimerListAdd: add timer obj c05e4a18!
 +RTMP_TimerListAdd: add timer obj c05e4a48!
 +RTMP_TimerListAdd: add timer obj c05e4c08!
 +RTMP_TimerListAdd: add timer obj c05e4c38!
 +RTMP_TimerListAdd: add timer obj c05e7b88!
 +RTMP_TimerListAdd: add timer obj c05e777c!
 +RTMP_TimerListAdd: add timer obj c05e7b58!
 +RTMP_TimerListAdd: add timer obj c05e7f00!
 +RTMP_TimerListAdd: add timer obj c05e7c50!
 +RTMP_TimerListAdd: add timer obj c05e7c80!
 +RTMP_TimerListAdd: add timer obj c05e7e40!
 +RTMP_TimerListAdd: add timer obj c05e7e70!
 +RTMP_TimerListAdd: add timer obj c05eadc0!
 +RTMP_TimerListAdd: add timer obj c05ea9b4!
 +RTMP_TimerListAdd: add timer obj c05ead90!
 +RTMP_TimerListAdd: add timer obj c05eb138!
 +RTMP_TimerListAdd: add timer obj c05eae88!
 +RTMP_TimerListAdd: add timer obj c05eaeb8!
 +RTMP_TimerListAdd: add timer obj c05eb078!
 +RTMP_TimerListAdd: add timer obj c05eb0a8!
 +RTMP_TimerListAdd: add timer obj c05edff8!
 +RTMP_TimerListAdd: add timer obj c05edbec!
 +RTMP_TimerListAdd: add timer obj c05edfc8!
 +RTMP_TimerListAdd: add timer obj c05ee370!
 +RTMP_TimerListAdd: add timer obj c05ee0c0!
 +RTMP_TimerListAdd: add timer obj c05ee0f0!
 +RTMP_TimerListAdd: add timer obj c05ee2b0!
 +RTMP_TimerListAdd: add timer obj c05ee2e0!
 +RTMP_TimerListAdd: add timer obj c0633404!
 +RTMP_TimerListAdd: add timer obj c0632ff8!
 +RTMP_TimerListAdd: add timer obj c06333d4!
 +RTMP_TimerListAdd: add timer obj c063377c!
 +RTMP_TimerListAdd: add timer obj c06334cc!
 +RTMP_TimerListAdd: add timer obj c06334fc!
 +RTMP_TimerListAdd: add timer obj c0633434!
 +RTMP_TimerListAdd: add timer obj c0633464!
 +RTMP_TimerListAdd: add timer obj c0633494!
 +RTMP_TimerListAdd: add timer obj c063c7ec!
 +RTMP_TimerListAdd: add timer obj c063c908!
 +RTMP_TimerListAdd: add timer obj c063c818!
 +RTMP_TimerListAdd: add timer obj c0633b24!
 +RTMP_TimerListAdd: add timer obj c05d5530!
 +RTMP_TimerListAdd: add timer obj c05d8768!
 +RTMP_TimerListAdd: add timer obj c05db9a0!
 +RTMP_TimerListAdd: add timer obj c05debd8!
 +RTMP_TimerListAdd: add timer obj c05e1e10!
 +RTMP_TimerListAdd: add timer obj c05e5048!
 +RTMP_TimerListAdd: add timer obj c05e8280!
 +RTMP_TimerListAdd: add timer obj c05eb4b8!
 +RTMP_TimerListAdd: add timer obj c0633838!
 +APSDCapable[0]=0
 +APSDCapable[1]=0
 +APSDCapable[2]=0
 +APSDCapable[3]=0
 +APSDCapable[4]=0
 +APSDCapable[5]=0
 +APSDCapable[6]=0
 +APSDCapable[7]=0
 +APSDCapable[8]=0
 +APSDCapable[9]=0
 +APSDCapable[10]=0
 +APSDCapable[11]=0
 +APSDCapable[12]=0
 +APSDCapable[13]=0
 +APSDCapable[14]=0
 +APSDCapable[15]=0
 +default ApCliAPSDCapable[0]=0
 +Key2Str is Invalid key length(0) or Type(0)
 +Key3Str is Invalid key length(0) or Type(0)
 +Key4Str is Invalid key length(0) or Type(0)
 +1. Phy Mode = 9
 +2. Phy Mode = 9
 +E2PROM: D0 target power=0xff20 
 +E2PROM: 40 MW Power Delta= 0 
 +3. Phy Mode = 9
 +RTMP_TimerListAdd: add timer obj c05d5128!
 +AntCfgInit: primary/secondary ant 0/1
 +Initialize RF Central Registers for E2 !!!
 +Initialize RF Central Registers for E3 !!!
 +Initialize RF Channel Registers for E2 !!!
 +Initialize RF Channel Registers for E3 !!!
 +Initialize RF DCCal Registers for E2 !!!
 +Initialize RF DCCal Registers for E3 !!!
 +D1 = -1, D2 = 5, CalCode = 14 !!!
 +RT6352_Temperature_Init : BBPR49 = 0xffffffff
 +RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5
 +Current Temperature from BBP_R49=0xfffffff2
 + TX BW Filter Calibration !!!
 + RX BW Filter Calibration !!!
 +LOFT Calibration Done!
 +IQCalibration Start!
 +IQCalibration Done! CH = 0, (gain= 1, phase=3c)
 +IQCalibration Start!
 +IQCalibration Done! CH = 1, (gain= f, phase=3e)
 +TX IQ Calibration Done!
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +MCS Set = ff ff 00 00 01
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +RTMP_TimerListAdd: add timer obj c06340c8!
 +Main bssid = 90:ef:68:2e:40:b0
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +load fw spent 16ms
 +RX DESC a2019000 size = 2048
 +RX1 DESC a201a000 size = 2048
 +cfg_mode=14
 +cfg_mode=14
 +wmode_band_equal(): Band Not Equal!
 +1. Phy Mode = 49
 +2. Phy Mode = 49
 +drivers/net/wireless/MT7610_ap/chips/mt76x0.c:2196 assert (pAd->TxPower[choffset].Channel == 36)failed
 +ext_pa_current_setting = 1
 +TXALC> bInternalTxALC = 0
 +3. Phy Mode = 49
 +AntCfgInit: primary/secondary ant 0/1
 +ChipStructAssign(): RALINK6590 hook !
 +MCS Set = ff 00 00 00 01
 +MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
 +APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
 +Main bssid = 90:ef:68:2e:40:b4
 +<==== rt28xx_init, Status=0
 +MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1
 +FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255
 +FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255
 +FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255
 +FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 52, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 52, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 56, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 56, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 60, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 60, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 64, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 64, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 100, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 100, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 104, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 104, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 108, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 108, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 112, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 112, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 116, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 116, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 120, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 120, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 124, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 124, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 128, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 128, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 132, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 132, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 136, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 136, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 140, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 140, param = 0x901, bSave = 0, CalibrationMode = 255
 +MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42
 +APStartUp(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
 +MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
 +0x1300 = 00064380
 +RTMPDrvOpen(1):Check if PDMA is idle!
 +RTMPDrvOpen(2):Check if PDMA is idle!
 +ifconfig: ioctl 0x8913 failed: No such device
 +brctl: bridge br0: No such device or address
 +Raeth v3.0 (Tasklet,SkbRecycle)
 +
 +phy_tx_ring = 0x0184d000, tx_ring = 0xa184d000
 +
 +phy_rx_ring0 = 0x0184e000, rx_ring0 = 0xa184e000
 +SMACCR1 -- : 0x000090ef
 +SMACCR0 -- : 0x682e40b1
 +CDMA_CSG_CFG = 81000000
 +GDMA1_FWD_CFG = 20710000
 +vconfig: ioctl error for rem: No such device
 +vconfig: ioctl error for rem: No such device
 +rmmod: 8021q: No such file or directory
 +insmod: 8021q.ko: module not found
 +##### config Ralink ESW vlan partition (LLLLW) #####
 +switch reg write offset=2004, value=ff0003
 +switch reg write offset=2104, value=ff0003
 +switch reg write offset=2204, value=ff0003
 +switch reg write offset=2304, value=ff0003
 +switch reg write offset=2404, value=ff0003
 +switch reg write offset=2504, value=ff0003
 +switch reg write offset=2010, value=810000c0
 +switch reg write offset=2110, value=810000c0
 +switch reg write offset=2210, value=810000c0
 +switch reg write offset=2310, value=810000c0
 +switch reg write offset=2410, value=810000c0
 +switch reg write offset=2510, value=810000c0
 +switch reg write offset=2610, value=81000000
 +switch reg write offset=2710, value=81000000
 +switch reg write offset=2604, value=20ff0003
 +switch reg write offset=2704, value=20ff0003
 +Special Tag Disabled
 +switch reg write offset=2610, value=81000000
 +switch reg write offset=2014, value=10001
 +switch reg write offset=2114, value=10001
 +switch reg write offset=2214, value=10001
 +switch reg write offset=2314, value=10001
 +switch reg write offset=2414, value=10002
 +switch reg write offset=2514, value=10001
 +REG_ESW_WT_MAC_ATC is 0x7ff0002
 +done.
 +EMIL DEBUG : addRaix2Br0() - 
 +
 +##### enable 2nd wireless interface #####
 +Enlarge min_free_kbytes....
 +==================Start Kill TimeTool Daemon!!!!!==================
 +CloneMAC mode is 0...
 +Enter timetool 
 +udhcpc (v1.12.1) started
 +ifconfig: ioctl 0x8914 failed: Cannot assign requested address
 +ifconfig: ioctl 0x8914 failed: Cannot assign requested address
 +******** Re-write DHCP file ********
 +cat: can't open '/etc/resolv.conf': No such file or directory
 +dhcp_DnsMode is 9...
 +killall: udhcpd: no process killed
 +Set: phy[0].reg[0] = 3900
 +Set: phy[1].reg[0] = 3900
 +Set: phy[2].reg[0] = 3900
 +Set: phy[3].reg[0] = 3900
 +Set: phy[0].reg[0] = 3300
 +Set: phy[1].reg[0] = 3300
 +Set: phy[2].reg[0] = 3300
 +Set: phy[3].reg[0] = 3300
 +EMIL DEBUG : 1, 192.168.1.1
 +killall: nmbd: no process killed
 +
 +***** g_wl_interface = ra0 ******
 +
 +iwpriv ra0 set IgmpSnEnable=1
 +iwpriv rai0 set IgmpSnEnable=1
 +Start  initInternet!!!!!   system[internet.sh] = 0
 +   sRL debug: AQ_LAN_IP=c0a80101
 +ysRL debug: AQ_SHIFT_COUNT=8
 +teRL debug: AQ_HTTP_PORT=50
 +m[AccessLAN.sh] = 0
 +   system[killall rt2860apd 1>/dev/null 2>&1] = 256
 +   system[killall rtinicapd 1>/dev/null 2>&1] = 256
 +   system[mkdir -p /var/spool/cron/crontabs] = 0
 +   system[rm -f /var/spool/cron/crontabs/scheduler] = 0
 +   system[rm -f /var/spool/cron/crontabs/scheduler5G] = 0
 +   system[cat /var/spool/cron/crontabs/temp.dat > /var/spool/cron/crontabs/admin] = 0
 +   system[rm -f /var/spool/cron/crontabs/temp.dat] = 0
 +
 +2.4G and 5G no scheduling
 +killall: crond: no process killed
 +   system[killall crond] = 256
 +   system[iwpriv ra0 set RadioOn=1] = 0
 +   system[echo 1 > /var/SchedulerRadioOn] = 0
 +   system[iwpriv rai0 set RadioOn=1] = 0
 +   system[echo 1 > /var/SchedulerRadioOn5G] = 0led=55, on=1, off=4000, blinks,=1, reset=1, time=4000
 +
 +   system[gpio l 55 0 4000 0 1 4000] = 0
 +=================== iptablesAllFilterClear  =============
 +   system[iptables -F -t filter 1>/dev/null 2>&1] = 0
 +   system[iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1] = 512
 +   system[iptables -F macipport_filter 1>/dev/null 2>&1] = 256
 +   system[iptables -D FORWARD -j web_filter  1>/dev/null 2>&1] = 512
 +   system[iptables -F web_filter  1>/dev/null 2>&1] = 256
 +   system[iptables -X dos_block  1>/dev/null 2>&1] = 256
 +   system[iptables -X dos_log  1>/dev/null 2>&1] = 256
 +   system[iptables -X port_trigger  1>/dev/null 2>&1] = 256
 +   system[iptables -D FORWARD -j DMZ_FORWARD  1>/dev/null 2>&1] = 512
 +   system[iptables -F DMZ_FORWARD  1>/dev/null 2>&1] = 256
 +   system[iptables -P INPUT ACCEPT] = 0
 +   system[iptables -P FORWARD DROP] = 0
 +   system[iptables -P OUTPUT ACCEPT] = 0
 +   system[iptables -P INPUT ACCEPT] = 0
 +   system[iptables -P FORWARD ACCEPT] = 0
 +===================START Filter Chain  =============
 +   system[iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N dos_block 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A INPUT -j dos_block 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N dos_log 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A INPUT -j dos_log 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N web_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N macipport_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N port_forward 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j port_forward 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N port_trigger 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j port_trigger 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N DMZ_FORWARD 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j DMZ_FORWARD 1>/dev/null 2>&1] = 0
 +=================== iptablesAllFilterRun  =============
 +websTrustedIPAddress is null
 +===================START NAT Chain  =============
 +=================== iptablesAllNATClear  =============
 +   system[iptables -t nat -D PREROUTING -j port_trigger  1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F port_trigger  1>/dev/null 2>&1; iptables -t nat -X port_trigger  1>/dev/null 2>&1] = 256
 +   system[iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1] = 256
 +   system[iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1] = 256
 +   system[iptables -t nat -D POSTROUTING -j DMZ_POST  1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F DMZ_POST  1>/dev/null 2>&1; iptables -t nat -X DMZ_POST  1>/dev/null 2>&1] = 256
 +   system[iptables -F -t nat 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j DMZ 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N port_trigger 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_trigger 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N port_forward_post 1>/dev/null 2>&1; iptables -t nat -A POSTROUTING -j port_forward_post 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N DMZ_POST 1>/dev/null 2>&1; iptables -t nat -A POSTROUTING -j DMZ_POST 1>/dev/null 2>&1] = 0
 +=================== iptablesAllNATRun  =============
 +Enter iptablesPortForwardRun
 +Enter iptablesPortTriggerRun
 +WAN IP error
 +=================== iptablesNATBasic  =============
 +   system[iptables -t nat -A POSTROUTING -o eth2.2 -j MASQUERADE] = 0
 +===>>>Start iptablesWANServiceRun !!!
 +   system[iptables -t filter -F INPUT] = 0
 +   system[iptables -t filter -I INPUT -i eth2.2 -d 192.168.1.1 -p icmp --icmp-type echo-request -j DROP] = 0
 +Disable WAN Ping
 +WAN IP error -> do something
 +   system[echo 0 > /proc/sys/net/ipv4/ip_forward] = 0
 +   system[echo 1 > /proc/sys/net/ipv4/ip_forward] = 0
 +   system[iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT] = 0
 +Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
 +   system[iptables -A INPUT -i ! eth2.2 -j ACCEPT] = 0
 +   system[iptables -F dos_block  1>/dev/null 2>&1] = 0
 +   system[iptables -F dos_log  1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A INPUT -j dos_block 1>/dev/null 2>&1] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL FIN,URG,PSH -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL ALL -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL NONE -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags SYN,RST SYN,RST -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL FIN -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags FIN,RST FIN,RST -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ACK,FIN FIN -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ACK,URG URG -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ACK,PSH PSH -j DROP] = 0
 +   system[iptables -A dos_block -m state --state INVALID -j DROP] = 0
 +   system[iptables -A dos_block -p tcp ! --syn -m state --state NEW -j DROP] = 0
 +   system[iptables -A FORWARD -p udp -i eth2.2 -o br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -p tcp -i eth2.2 -o br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -p icmp -i eth2.2 -o br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -i br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -i eth2.2 -m state --state RELATED,ESTABLISHED -j ACCEPT ] = 0
 +   system[ip6tables -F INPUT] = 0
 +   system[ip6tables -P INPUT ACCEPT] = 0
 +   system[ip6tables -F FORWARD] = 0
 +   system[ip6tables -P FORWARD ACCEPT] = 0
 +   system[ip6tables -F OUTPUT] = 0
 +   system[ip6tables -P OUTPUT ACCEPT] = 0
 +EMIL DEBUG : 1
 +killall: ntp.sh: no process killed
 +   system[killall ntp.sh] = 256
 +   system[ntp.sh &] = 0
 +DDNS not Enable.
 +   system[ddns.sh] = 0
 +   system[udps &] = 0
 +Enter udps 
 + 
 +
 +   system[cplange.sh &] = 0
 +sh: cplange.sh: not found
 +   system[iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1] = 0
 +   system[route delete 239.255.255.250 1>/dev/null 2>&1] = 256
 +Ntpserver is 192.5.41.41
 +connect: Network is unreachable
 +sleep 4.....
 +   system[miniupnpd.sh init] = 0
 +   system[iwpriv rai0 set WscConfMode=0 1>/dev/null 2>&1] = 0
 +   system[route delete 239.255.255.250 1>/dev/null 2>&1] = 256
 +   system[miniupnpd.sh init] = 0
 +   system[echo '1' >  /tmp/syslodg_exist] = 0
 +   system[syslogd -C8 1>/dev/null 2>&1] = 0
 +   system[klogd 1>/dev/null 2>&1] = 0
 +   system[killall -q zebra] = 256
 +   system[killall -q ripd] = 256
 +RL : === start running QoS ===  
 +Gateway Mode
 +rl_qos: OP_MODE=0
 +rl_qos: WAN_IF=eth2.2
 +rl_qos: LAN_IF=br0
 +rl_qos: WLAN_IF=(null)
 +rl_qos: BR_IF=br0
 +rl_qos: qosEnable=0
 +rl_qos: qosAutoEnable=0
 +rl_qos: UPLINK_SPEED=51200
 +rl_qos: DOWNLINK_SPEED=51200
 +=====QoS DISABLED!!...======
 +   system[/sbin/rl_qos] = 0
 +RL modified timeout parameter in xxM.
 +===== Start IPv6 Setting ======
 +Cannot find device "sixtun"
 +   system[ip link set sixtun down] = 65280
 +killall: dhcp6s: no process killed
 +   system[killall dhcp6s] = 256
 +killall: dhcp6c: no process killed
 +   system[killall dhcp6c] = 256
 +killall: radvd: no process killed
 +   system[killall radvd] = 256
 +   system[echo 0 > /proc/sys/net/ipv6/conf/all/forwarding] = 0
 +Mode=4, Enter Link Local
 +===== End IPv6 Setting ======
 +BoA: reload parameter into BoA webserver!
 +led=39, on=4000, off=1, blinks,=1, reset=1, time=4000
 +The rmPort is 80 
 +Ntpserver is 192.5.41.209
 +connect: Network is unreachable
 +sleep 4.....
 +Ntpserver is 203.117.180.36
 +</WRAP>\\
 +
 +
 +
 +===== Links =====
 +
 +  * https://wikidevi.com/wiki/ZyXEL_NBG6503
 +
 +
 +
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>802.11ac mt7620 mt7610e 8Flash 64RAM unsupported}}
  • Last modified: 2020/09/27 20:23
  • by jhench