Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:zyxel:nbg6503 [2015/05/05 11:37] – [ZyXEL NBG6503] Link to wikidevi added tmomastoh:zyxel:nbg6503 [2020/09/13 20:01] – [ZyXEL NBG6503] corrected links. Tested with 19.07.3 jhench
Line 1: Line 1:
 +====== ZyXEL NBG6503 ======
  
 +[[wp>IEEE 802.11ac]]-capable device from 2013. FCC ID: I88NBG6503
 +
 +  * MediaTek MT7620A-based
 +  * includes MediaTek MT7610en
 +  * 19.07.3: mt7620a-initramfs-kernel.bin is bootable to prompt with TTL serial 57600,8,1 (3.3V)
 +  * bootable from TFTP (without flashing) with this image: [[https://downloads.openwrt.org/releases/19.07.3/targets/ramips/mt7620/openwrt-19.07.3-ramips-mt7620-rt-ac51u-initramfs-kernel.bin]]
 +  * flashing this image works, stays without overlays
 +  * from within openWRT, upgrade with the image [[https://downloads.openwrt.org/releases/19.07.3/targets/ramips/mt7620/openwrt-19.07.3-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin]] through the LuCi interface, and overlayfs will work
 +  * LuCi / WiFi seem to work
 +  * WAN does not work (DHCP client fails)
 +
 +{{media:zyxel:nbg6503_general_view.png?200}}
 +
 +Bootlog (original firmware)
 +<WRAP bootlog>
 +user@PC:~$ picocom -b 57600 /dev/ttyUSB0
 +picocom v2.2
 +
 +port is        : /dev/ttyUSB0
 +flowcontrol    : none
 +baudrate is    : 57600
 +parity is      : none
 +databits are   : 8
 +stopbits are   : 1
 +escape is      : C-a
 +local echo is  : no
 +noinit is      : no
 +noreset is     : no
 +nolock is      : no
 +send_cmd is    : sz -vv
 +receive_cmd is : rz -vv -E
 +imap is        : 
 +omap is        : 
 +emap is        : crcrlf,delbs,
 +
 +Type [C-a] [C-h] to see available commands
 +
 +Terminal ready
 +
 +
 +
 +
 +
 +U-Boot 1.1.3 (Mar 11 2013 - 11:11:53)
 +
 +Board: Ralink APSoC DRAM:  64 MB
 +relocate_code Pointer at: 83fb4000
 +enable ephy clock...done. rf reg 29 = 5
 +SSC disabled.
 +******************************
 +Software System Reset Occurred
 +******************************
 +spi_wait_nsec: 29 
 +spi device id: ef 40 17 0 0 (40170000)
 +find flash: W25Q64BV
 +raspi_read: from:30000 len:1000 
 +*** Warning - bad CRC, using default environment
 +
 +============================================ 
 +Ralink UBoot Version: 4.1.1.0_a2
 +-------------------------------------------- 
 +ASIC 7620_MP (Port5<->None)
 +DRAM component: 512 Mbits DDR, width 16
 +DRAM bus: 16 bit
 +Total memory: 64 MBytes
 +Flash component: SPI Flash
 +Date:Mar 11 2013  Time:11:11:53
 +============================================ 
 +icache: sets:512, ways:4, linesz:32 ,total:65536
 +dcache: sets:256, ways:4, linesz:32 ,total:32768 
 +
 + ##### The CPU freq = 580 MHZ #### 
 + estimate memory size =64 Mbytes
 +
 +Please choose the operation: 
 +   1: Load system code to SDRAM via TFTP. 
 +   2: Load system code then write to Flash via TFTP. 
 +   3: Boot system code via Flash (default).
 +   4: Entr boot command line interface.
 +   7: Load Boot Loader code then write to Flash via Serial. 
 +   9: Load Boot Loader code then write to Flash via TFTP. 
 +   a: Auto load system code then write to Flash via TFTP. 
 + 
 +   
 +3: System Boot system code via Flash.
 +## Booting image at bc050000 ...
 +raspi_read: from:50000 len:40 
 +   Image Name:   Linux Kernel Image
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    5380973 Bytes =  5.1 MB
 +   Load Address: 80000000
 +   Entry Point:  8000c310
 +raspi_read: from:50040 len:521b6d 
 +   Verifying Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 +No initrd
 +## Transferring control to Linux (at address 8000c310) ...
 +## Giving linux memsize in MB, 64
 +
 +Starting kernel ...
 +
 +
 +LINUX started...
 +
 + THIS IS ASIC
 +
 + The CPU feqenuce set to 580 MHz
 +
 + MIPS CPU sleep mode enabled.
 + PCIE: bypass PCIe DLL.
 + PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 + disable all power about PCIe
 +Zone PFN ranges:
 +  Normal   0x00000000 -> 0x00004000
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00004000
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +MTK/Ralink System Tick Counter init... cd:80397ef8, m:214748, s:32
 +Mount-cache hash table entries: 512
 +RALINK_GPIOMODE = 1a311d
 +RALINK_GPIOMODE = 18311d
 +PPLL_CFG1=0xe6c000
 +MT7620 PPLL lock
 +PPLL_DRV =0x80080504
 +PCIe reset again
 +start PCIe register access
 +RALINK_PCI_PCICFG_ADDR = 1000f0
 +
 +*************** MT7620 PCIe RC mode *************
 +bio: create slab <bio-0> at 0
 +BAR0 at slot 0 = 0
 +bus=0x0, slot = 0x0
 +res[0]->start = 0
 +res[0]->end = 0
 +res[1]->start = 20200000
 +res[1]->end = 2020ffff
 +res[2]->start = 0
 +res[2]->end = 0
 +res[3]->start = 0
 +res[3]->end = 0
 +res[4]->start = 0
 +res[4]->end = 0
 +res[5]->start = 0
 +res[5]->end = 0
 +bus=0x1, slot = 0x0
 +res[0]->start = 20000000
 +res[0]->end = 200fffff
 +res[1]->start = 0
 +res[1]->end = 0
 +res[2]->start = 0
 +res[2]->end = 0
 +res[3]->start = 0
 +res[3]->end = 0
 +res[4]->start = 0
 +res[4]->end = 0
 +res[5]->start = 0
 +res[5]->end = 0
 +bus=0x1, slot = 0x0
 +res[0]->start = 20100000
 +res[0]->end = 201fffff
 +res[1]->start = 0
 +res[1]->end = 0
 +res[2]->start = 0
 +res[2]->end = 0
 +res[3]->start = 0
 +res[3]->end = 0
 +res[4]->start = 0
 +res[4]->end = 0
 +res[5]->start = 0
 +res[5]->end = 0
 +RT3xxx EHCI/OHCI init.
 +Ralink gpio driver initialized
 +deice id : ef 40 17 0 0 (40170000)
 +W25Q64BV(ef 40170000) (8192 Kbytes)
 +mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
 +mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
 +rdm_major = 253
 +SMACCR1 -- : 0x000090ef
 +SMACCR0 -- : 0x682e40b1
 +Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
 +SMACCR1 -- : 0x000090ef
 +SMACCR0 -- : 0x682e40b1
 +nf_conntrack version 0.5.0 (888 buckets, 3552 max 400 reserved)
 +matchsize=264
 +init started: BusyBox v1.12.1 Algorithmics/MIPS FPU Emulator v1.5
 +(2014-11-25 11:16:51 CST)
 +starting pid 34, tty '': '/etc_ro/rcS'
 +mount: mounting none on /proc/bus/usb failed: No such file or directory
 +ftpalg: Waiting for message from kernel
 +starting pid 46, tty '/dev/ttyS1': '/bin/sh'
 +
 +
 +BusyBox v1.12.1 (2014-11-25 11:16:51 CST) built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +# boa: waiting for nvram_daemon 
 +@@@ BssidNum @@@
 +
 +@led=38, on=1, off=4000, blinks,=1, reset=1, time=4000
 +@@ BssidNum @@@
 +@@@  check_nvram_loadf  @@@
 +nvram flash is ok
 +rai0      no private ioctls.
 +
 +ifconfig: ioctl 0x8913 failed: No such device
 +Password for 'admin' changed
 +rmmod: ralink_wdt: No such file or directory
 +rmmod: cls: No such file or directory
 +rmmod: hw_nat: No such file or directory
 +rmmod: raeth: No such file or directory
 +insmod: bridge.ko: module not found
 +insmod: mii.ko: module not found
 +insmod: raeth.ko: module not found
 +
 +##### disable 1st wireless interface #####
 +rai0      no private ioctls.
 +
 +
 +##### disable 2nd wireless interface #####
 +rmmod: rt2860v2_ap_net: No such file or directory
 +rmmod: rt2860v2_ap: No such file or directory
 +rmmod: rt2860v2_ap_util: No such file or directory
 +rmmod: MT7610_ap: No such file or directory
 +insmod: rt_timer.ko: module not found
 +insmod: rt2860v2_ap_util.ko: module not found
 +rt2860v2_ap: module license 'unspecified' taints kernel.
 +Disabling lock debugging due to kernel taint
 +
 +
 +=== pAd = c05d0000, size = 808936 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +AP Driver version-2.7.1.6_20130807
 +insmod: rt2860v2_ap_net.ko: module not found
 +
 +
 +=== pAd = c0b02000, size = 944472 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +device_id =0x7650
 +==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
 +MACVersion = 0x76502000
 +RX DESC a23fe000  size = 2048
 +RTMP_TimerListAdd: add timer obj c0665e80!
 +RTMP_TimerListAdd: add timer obj c0631000!
 +RTMP_TimerListAdd: add timer obj c0630fd4!
 +RTMP_TimerListAdd: add timer obj c0630fa8!
 +RTMP_TimerListAdd: add timer obj c05d8070!
 +RTMP_TimerListAdd: add timer obj c05d7c64!
 +RTMP_TimerListAdd: add timer obj c05d8040!
 +RTMP_TimerListAdd: add timer obj c05d83e8!
 +RTMP_TimerListAdd: add timer obj c05d8138!
 +RTMP_TimerListAdd: add timer obj c05d8168!
 +RTMP_TimerListAdd: add timer obj c05d8328!
 +RTMP_TimerListAdd: add timer obj c05d8358!
 +RTMP_TimerListAdd: add timer obj c05db2a8!
 +RTMP_TimerListAdd: add timer obj c05dae9c!
 +RTMP_TimerListAdd: add timer obj c05db278!
 +RTMP_TimerListAdd: add timer obj c05db620!
 +RTMP_TimerListAdd: add timer obj c05db370!
 +RTMP_TimerListAdd: add timer obj c05db3a0!
 +RTMP_TimerListAdd: add timer obj c05db560!
 +RTMP_TimerListAdd: add timer obj c05db590!
 +RTMP_TimerListAdd: add timer obj c05de4e0!
 +RTMP_TimerListAdd: add timer obj c05de0d4!
 +RTMP_TimerListAdd: add timer obj c05de4b0!
 +RTMP_TimerListAdd: add timer obj c05de858!
 +RTMP_TimerListAdd: add timer obj c05de5a8!
 +RTMP_TimerListAdd: add timer obj c05de5d8!
 +RTMP_TimerListAdd: add timer obj c05de798!
 +RTMP_TimerListAdd: add timer obj c05de7c8!
 +RTMP_TimerListAdd: add timer obj c05e1718!
 +RTMP_TimerListAdd: add timer obj c05e130c!
 +RTMP_TimerListAdd: add timer obj c05e16e8!
 +RTMP_TimerListAdd: add timer obj c05e1a90!
 +RTMP_TimerListAdd: add timer obj c05e17e0!
 +RTMP_TimerListAdd: add timer obj c05e1810!
 +RTMP_TimerListAdd: add timer obj c05e19d0!
 +RTMP_TimerListAdd: add timer obj c05e1a00!
 +RTMP_TimerListAdd: add timer obj c05e4950!
 +RTMP_TimerListAdd: add timer obj c05e4544!
 +RTMP_TimerListAdd: add timer obj c05e4920!
 +RTMP_TimerListAdd: add timer obj c05e4cc8!
 +RTMP_TimerListAdd: add timer obj c05e4a18!
 +RTMP_TimerListAdd: add timer obj c05e4a48!
 +RTMP_TimerListAdd: add timer obj c05e4c08!
 +RTMP_TimerListAdd: add timer obj c05e4c38!
 +RTMP_TimerListAdd: add timer obj c05e7b88!
 +RTMP_TimerListAdd: add timer obj c05e777c!
 +RTMP_TimerListAdd: add timer obj c05e7b58!
 +RTMP_TimerListAdd: add timer obj c05e7f00!
 +RTMP_TimerListAdd: add timer obj c05e7c50!
 +RTMP_TimerListAdd: add timer obj c05e7c80!
 +RTMP_TimerListAdd: add timer obj c05e7e40!
 +RTMP_TimerListAdd: add timer obj c05e7e70!
 +RTMP_TimerListAdd: add timer obj c05eadc0!
 +RTMP_TimerListAdd: add timer obj c05ea9b4!
 +RTMP_TimerListAdd: add timer obj c05ead90!
 +RTMP_TimerListAdd: add timer obj c05eb138!
 +RTMP_TimerListAdd: add timer obj c05eae88!
 +RTMP_TimerListAdd: add timer obj c05eaeb8!
 +RTMP_TimerListAdd: add timer obj c05eb078!
 +RTMP_TimerListAdd: add timer obj c05eb0a8!
 +RTMP_TimerListAdd: add timer obj c05edff8!
 +RTMP_TimerListAdd: add timer obj c05edbec!
 +RTMP_TimerListAdd: add timer obj c05edfc8!
 +RTMP_TimerListAdd: add timer obj c05ee370!
 +RTMP_TimerListAdd: add timer obj c05ee0c0!
 +RTMP_TimerListAdd: add timer obj c05ee0f0!
 +RTMP_TimerListAdd: add timer obj c05ee2b0!
 +RTMP_TimerListAdd: add timer obj c05ee2e0!
 +RTMP_TimerListAdd: add timer obj c0633404!
 +RTMP_TimerListAdd: add timer obj c0632ff8!
 +RTMP_TimerListAdd: add timer obj c06333d4!
 +RTMP_TimerListAdd: add timer obj c063377c!
 +RTMP_TimerListAdd: add timer obj c06334cc!
 +RTMP_TimerListAdd: add timer obj c06334fc!
 +RTMP_TimerListAdd: add timer obj c0633434!
 +RTMP_TimerListAdd: add timer obj c0633464!
 +RTMP_TimerListAdd: add timer obj c0633494!
 +RTMP_TimerListAdd: add timer obj c063c7ec!
 +RTMP_TimerListAdd: add timer obj c063c908!
 +RTMP_TimerListAdd: add timer obj c063c818!
 +RTMP_TimerListAdd: add timer obj c0633b24!
 +RTMP_TimerListAdd: add timer obj c05d5530!
 +RTMP_TimerListAdd: add timer obj c05d8768!
 +RTMP_TimerListAdd: add timer obj c05db9a0!
 +RTMP_TimerListAdd: add timer obj c05debd8!
 +RTMP_TimerListAdd: add timer obj c05e1e10!
 +RTMP_TimerListAdd: add timer obj c05e5048!
 +RTMP_TimerListAdd: add timer obj c05e8280!
 +RTMP_TimerListAdd: add timer obj c05eb4b8!
 +RTMP_TimerListAdd: add timer obj c0633838!
 +APSDCapable[0]=0
 +APSDCapable[1]=0
 +APSDCapable[2]=0
 +APSDCapable[3]=0
 +APSDCapable[4]=0
 +APSDCapable[5]=0
 +APSDCapable[6]=0
 +APSDCapable[7]=0
 +APSDCapable[8]=0
 +APSDCapable[9]=0
 +APSDCapable[10]=0
 +APSDCapable[11]=0
 +APSDCapable[12]=0
 +APSDCapable[13]=0
 +APSDCapable[14]=0
 +APSDCapable[15]=0
 +default ApCliAPSDCapable[0]=0
 +Key2Str is Invalid key length(0) or Type(0)
 +Key3Str is Invalid key length(0) or Type(0)
 +Key4Str is Invalid key length(0) or Type(0)
 +1. Phy Mode = 9
 +2. Phy Mode = 9
 +E2PROM: D0 target power=0xff20 
 +E2PROM: 40 MW Power Delta= 0 
 +3. Phy Mode = 9
 +RTMP_TimerListAdd: add timer obj c05d5128!
 +AntCfgInit: primary/secondary ant 0/1
 +Initialize RF Central Registers for E2 !!!
 +Initialize RF Central Registers for E3 !!!
 +Initialize RF Channel Registers for E2 !!!
 +Initialize RF Channel Registers for E3 !!!
 +Initialize RF DCCal Registers for E2 !!!
 +Initialize RF DCCal Registers for E3 !!!
 +D1 = -1, D2 = 5, CalCode = 14 !!!
 +RT6352_Temperature_Init : BBPR49 = 0xffffffff
 +RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5
 +Current Temperature from BBP_R49=0xfffffff2
 + TX BW Filter Calibration !!!
 + RX BW Filter Calibration !!!
 +LOFT Calibration Done!
 +IQCalibration Start!
 +IQCalibration Done! CH = 0, (gain= 1, phase=3c)
 +IQCalibration Start!
 +IQCalibration Done! CH = 1, (gain= f, phase=3e)
 +TX IQ Calibration Done!
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +MCS Set = ff ff 00 00 01
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +SYNC - BBP R4 to 20MHz.l
 +RTMP_TimerListAdd: add timer obj c06340c8!
 +Main bssid = 90:ef:68:2e:40:b0
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +load fw spent 16ms
 +RX DESC a2019000 size = 2048
 +RX1 DESC a201a000 size = 2048
 +cfg_mode=14
 +cfg_mode=14
 +wmode_band_equal(): Band Not Equal!
 +1. Phy Mode = 49
 +2. Phy Mode = 49
 +drivers/net/wireless/MT7610_ap/chips/mt76x0.c:2196 assert (pAd->TxPower[choffset].Channel == 36)failed
 +ext_pa_current_setting = 1
 +TXALC> bInternalTxALC = 0
 +3. Phy Mode = 49
 +AntCfgInit: primary/secondary ant 0/1
 +ChipStructAssign(): RALINK6590 hook !
 +MCS Set = ff 00 00 00 01
 +MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
 +APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
 +Main bssid = 90:ef:68:2e:40:b4
 +<==== rt28xx_init, Status=0
 +MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1
 +FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255
 +FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255
 +FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255
 +FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 52, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 52, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 56, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 56, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 60, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 60, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 64, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 64, param = 0x701, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 100, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 100, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 104, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 104, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 108, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 108, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 112, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 112, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 116, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 116, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 120, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 120, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 124, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 124, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 128, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 128, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 132, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 132, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 136, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 136, param = 0x801, bSave = 0, CalibrationMode = 255
 +MT76x0_Calibration - Channel = 140, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 140, param = 0x901, bSave = 0, CalibrationMode = 255
 +MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42
 +APStartUp(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
 +MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0
 +FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
 +0x1300 = 00064380
 +RTMPDrvOpen(1):Check if PDMA is idle!
 +RTMPDrvOpen(2):Check if PDMA is idle!
 +ifconfig: ioctl 0x8913 failed: No such device
 +brctl: bridge br0: No such device or address
 +Raeth v3.0 (Tasklet,SkbRecycle)
 +
 +phy_tx_ring = 0x0184d000, tx_ring = 0xa184d000
 +
 +phy_rx_ring0 = 0x0184e000, rx_ring0 = 0xa184e000
 +SMACCR1 -- : 0x000090ef
 +SMACCR0 -- : 0x682e40b1
 +CDMA_CSG_CFG = 81000000
 +GDMA1_FWD_CFG = 20710000
 +vconfig: ioctl error for rem: No such device
 +vconfig: ioctl error for rem: No such device
 +rmmod: 8021q: No such file or directory
 +insmod: 8021q.ko: module not found
 +##### config Ralink ESW vlan partition (LLLLW) #####
 +switch reg write offset=2004, value=ff0003
 +switch reg write offset=2104, value=ff0003
 +switch reg write offset=2204, value=ff0003
 +switch reg write offset=2304, value=ff0003
 +switch reg write offset=2404, value=ff0003
 +switch reg write offset=2504, value=ff0003
 +switch reg write offset=2010, value=810000c0
 +switch reg write offset=2110, value=810000c0
 +switch reg write offset=2210, value=810000c0
 +switch reg write offset=2310, value=810000c0
 +switch reg write offset=2410, value=810000c0
 +switch reg write offset=2510, value=810000c0
 +switch reg write offset=2610, value=81000000
 +switch reg write offset=2710, value=81000000
 +switch reg write offset=2604, value=20ff0003
 +switch reg write offset=2704, value=20ff0003
 +Special Tag Disabled
 +switch reg write offset=2610, value=81000000
 +switch reg write offset=2014, value=10001
 +switch reg write offset=2114, value=10001
 +switch reg write offset=2214, value=10001
 +switch reg write offset=2314, value=10001
 +switch reg write offset=2414, value=10002
 +switch reg write offset=2514, value=10001
 +REG_ESW_WT_MAC_ATC is 0x7ff0002
 +done.
 +EMIL DEBUG : addRaix2Br0() - 
 +
 +##### enable 2nd wireless interface #####
 +Enlarge min_free_kbytes....
 +==================Start Kill TimeTool Daemon!!!!!==================
 +CloneMAC mode is 0...
 +Enter timetool 
 +udhcpc (v1.12.1) started
 +ifconfig: ioctl 0x8914 failed: Cannot assign requested address
 +ifconfig: ioctl 0x8914 failed: Cannot assign requested address
 +******** Re-write DHCP file ********
 +cat: can't open '/etc/resolv.conf': No such file or directory
 +dhcp_DnsMode is 9...
 +killall: udhcpd: no process killed
 +Set: phy[0].reg[0] = 3900
 +Set: phy[1].reg[0] = 3900
 +Set: phy[2].reg[0] = 3900
 +Set: phy[3].reg[0] = 3900
 +Set: phy[0].reg[0] = 3300
 +Set: phy[1].reg[0] = 3300
 +Set: phy[2].reg[0] = 3300
 +Set: phy[3].reg[0] = 3300
 +EMIL DEBUG : 1, 192.168.1.1
 +killall: nmbd: no process killed
 +
 +***** g_wl_interface = ra0 ******
 +
 +iwpriv ra0 set IgmpSnEnable=1
 +iwpriv rai0 set IgmpSnEnable=1
 +Start  initInternet!!!!!   system[internet.sh] = 0
 +   sRL debug: AQ_LAN_IP=c0a80101
 +ysRL debug: AQ_SHIFT_COUNT=8
 +teRL debug: AQ_HTTP_PORT=50
 +m[AccessLAN.sh] = 0
 +   system[killall rt2860apd 1>/dev/null 2>&1] = 256
 +   system[killall rtinicapd 1>/dev/null 2>&1] = 256
 +   system[mkdir -p /var/spool/cron/crontabs] = 0
 +   system[rm -f /var/spool/cron/crontabs/scheduler] = 0
 +   system[rm -f /var/spool/cron/crontabs/scheduler5G] = 0
 +   system[cat /var/spool/cron/crontabs/temp.dat > /var/spool/cron/crontabs/admin] = 0
 +   system[rm -f /var/spool/cron/crontabs/temp.dat] = 0
 +
 +2.4G and 5G no scheduling
 +killall: crond: no process killed
 +   system[killall crond] = 256
 +   system[iwpriv ra0 set RadioOn=1] = 0
 +   system[echo 1 > /var/SchedulerRadioOn] = 0
 +   system[iwpriv rai0 set RadioOn=1] = 0
 +   system[echo 1 > /var/SchedulerRadioOn5G] = 0led=55, on=1, off=4000, blinks,=1, reset=1, time=4000
 +
 +   system[gpio l 55 0 4000 0 1 4000] = 0
 +=================== iptablesAllFilterClear  =============
 +   system[iptables -F -t filter 1>/dev/null 2>&1] = 0
 +   system[iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1] = 512
 +   system[iptables -F macipport_filter 1>/dev/null 2>&1] = 256
 +   system[iptables -D FORWARD -j web_filter  1>/dev/null 2>&1] = 512
 +   system[iptables -F web_filter  1>/dev/null 2>&1] = 256
 +   system[iptables -X dos_block  1>/dev/null 2>&1] = 256
 +   system[iptables -X dos_log  1>/dev/null 2>&1] = 256
 +   system[iptables -X port_trigger  1>/dev/null 2>&1] = 256
 +   system[iptables -D FORWARD -j DMZ_FORWARD  1>/dev/null 2>&1] = 512
 +   system[iptables -F DMZ_FORWARD  1>/dev/null 2>&1] = 256
 +   system[iptables -P INPUT ACCEPT] = 0
 +   system[iptables -P FORWARD DROP] = 0
 +   system[iptables -P OUTPUT ACCEPT] = 0
 +   system[iptables -P INPUT ACCEPT] = 0
 +   system[iptables -P FORWARD ACCEPT] = 0
 +===================START Filter Chain  =============
 +   system[iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N dos_block 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A INPUT -j dos_block 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N dos_log 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A INPUT -j dos_log 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N web_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N macipport_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N port_forward 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j port_forward 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N port_trigger 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j port_trigger 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -N DMZ_FORWARD 1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A FORWARD -j DMZ_FORWARD 1>/dev/null 2>&1] = 0
 +=================== iptablesAllFilterRun  =============
 +websTrustedIPAddress is null
 +===================START NAT Chain  =============
 +=================== iptablesAllNATClear  =============
 +   system[iptables -t nat -D PREROUTING -j port_trigger  1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F port_trigger  1>/dev/null 2>&1; iptables -t nat -X port_trigger  1>/dev/null 2>&1] = 256
 +   system[iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1] = 256
 +   system[iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1] = 256
 +   system[iptables -t nat -D POSTROUTING -j DMZ_POST  1>/dev/null 2>&1] = 512
 +   system[iptables -t nat -F DMZ_POST  1>/dev/null 2>&1; iptables -t nat -X DMZ_POST  1>/dev/null 2>&1] = 256
 +   system[iptables -F -t nat 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j DMZ 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N port_trigger 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_trigger 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N port_forward_post 1>/dev/null 2>&1; iptables -t nat -A POSTROUTING -j port_forward_post 1>/dev/null 2>&1] = 0
 +   system[iptables -t nat -N DMZ_POST 1>/dev/null 2>&1; iptables -t nat -A POSTROUTING -j DMZ_POST 1>/dev/null 2>&1] = 0
 +=================== iptablesAllNATRun  =============
 +Enter iptablesPortForwardRun
 +Enter iptablesPortTriggerRun
 +WAN IP error
 +=================== iptablesNATBasic  =============
 +   system[iptables -t nat -A POSTROUTING -o eth2.2 -j MASQUERADE] = 0
 +===>>>Start iptablesWANServiceRun !!!
 +   system[iptables -t filter -F INPUT] = 0
 +   system[iptables -t filter -I INPUT -i eth2.2 -d 192.168.1.1 -p icmp --icmp-type echo-request -j DROP] = 0
 +Disable WAN Ping
 +WAN IP error -> do something
 +   system[echo 0 > /proc/sys/net/ipv4/ip_forward] = 0
 +   system[echo 1 > /proc/sys/net/ipv4/ip_forward] = 0
 +   system[iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT] = 0
 +Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
 +   system[iptables -A INPUT -i ! eth2.2 -j ACCEPT] = 0
 +   system[iptables -F dos_block  1>/dev/null 2>&1] = 0
 +   system[iptables -F dos_log  1>/dev/null 2>&1] = 0
 +   system[iptables -t filter -A INPUT -j dos_block 1>/dev/null 2>&1] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL FIN,URG,PSH -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL ALL -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL NONE -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags SYN,RST SYN,RST -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ALL FIN -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags FIN,RST FIN,RST -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ACK,FIN FIN -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ACK,URG URG -j DROP] = 0
 +   system[iptables -A dos_block -p tcp --tcp-flags ACK,PSH PSH -j DROP] = 0
 +   system[iptables -A dos_block -m state --state INVALID -j DROP] = 0
 +   system[iptables -A dos_block -p tcp ! --syn -m state --state NEW -j DROP] = 0
 +   system[iptables -A FORWARD -p udp -i eth2.2 -o br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -p tcp -i eth2.2 -o br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -p icmp -i eth2.2 -o br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -i br0 -j ACCEPT] = 0
 +   system[iptables -A FORWARD -i eth2.2 -m state --state RELATED,ESTABLISHED -j ACCEPT ] = 0
 +   system[ip6tables -F INPUT] = 0
 +   system[ip6tables -P INPUT ACCEPT] = 0
 +   system[ip6tables -F FORWARD] = 0
 +   system[ip6tables -P FORWARD ACCEPT] = 0
 +   system[ip6tables -F OUTPUT] = 0
 +   system[ip6tables -P OUTPUT ACCEPT] = 0
 +EMIL DEBUG : 1
 +killall: ntp.sh: no process killed
 +   system[killall ntp.sh] = 256
 +   system[ntp.sh &] = 0
 +DDNS not Enable.
 +   system[ddns.sh] = 0
 +   system[udps &] = 0
 +Enter udps 
 + 
 +
 +   system[cplange.sh &] = 0
 +sh: cplange.sh: not found
 +   system[iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1] = 0
 +   system[route delete 239.255.255.250 1>/dev/null 2>&1] = 256
 +Ntpserver is 192.5.41.41
 +connect: Network is unreachable
 +sleep 4.....
 +   system[miniupnpd.sh init] = 0
 +   system[iwpriv rai0 set WscConfMode=0 1>/dev/null 2>&1] = 0
 +   system[route delete 239.255.255.250 1>/dev/null 2>&1] = 256
 +   system[miniupnpd.sh init] = 0
 +   system[echo '1' >  /tmp/syslodg_exist] = 0
 +   system[syslogd -C8 1>/dev/null 2>&1] = 0
 +   system[klogd 1>/dev/null 2>&1] = 0
 +   system[killall -q zebra] = 256
 +   system[killall -q ripd] = 256
 +RL : === start running QoS ===  
 +Gateway Mode
 +rl_qos: OP_MODE=0
 +rl_qos: WAN_IF=eth2.2
 +rl_qos: LAN_IF=br0
 +rl_qos: WLAN_IF=(null)
 +rl_qos: BR_IF=br0
 +rl_qos: qosEnable=0
 +rl_qos: qosAutoEnable=0
 +rl_qos: UPLINK_SPEED=51200
 +rl_qos: DOWNLINK_SPEED=51200
 +=====QoS DISABLED!!...======
 +   system[/sbin/rl_qos] = 0
 +RL modified timeout parameter in xxM.
 +===== Start IPv6 Setting ======
 +Cannot find device "sixtun"
 +   system[ip link set sixtun down] = 65280
 +killall: dhcp6s: no process killed
 +   system[killall dhcp6s] = 256
 +killall: dhcp6c: no process killed
 +   system[killall dhcp6c] = 256
 +killall: radvd: no process killed
 +   system[killall radvd] = 256
 +   system[echo 0 > /proc/sys/net/ipv6/conf/all/forwarding] = 0
 +Mode=4, Enter Link Local
 +===== End IPv6 Setting ======
 +BoA: reload parameter into BoA webserver!
 +led=39, on=4000, off=1, blinks,=1, reset=1, time=4000
 +The rmPort is 80 
 +Ntpserver is 192.5.41.209
 +connect: Network is unreachable
 +sleep 4.....
 +Ntpserver is 203.117.180.36
 +</WRAP>\\
 +
 +
 +
 +===== Links =====
 +
 +  * https://wikidevi.com/wiki/ZyXEL_NBG6503
 +
 +
 +
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>802.11ac mt7620 mt7610e 8Flash 64RAM unsupported}}
  • Last modified: 2020/09/27 20:23
  • by jhench