Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:zyxel:nbg419n [2018/04/05 23:11] – [Supported Versions] tmomas | toh:zyxel:nbg419n [2020/09/28 22:37] – [Installation] added information about flash size reccognition. jhench | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ZyXEL NBG-419N v1 / WAP3205 v1 ====== | ====== ZyXEL NBG-419N v1 / WAP3205 v1 ====== | ||
| + | |||
| + | {{section> | ||
| + | |||
| + | ^ NBG419N ^ WAP3205 ^ | ||
| + | | {{ media: | ||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| Line 12: | Line 17: | ||
| ---- | ---- | ||
| - | ^ NBG419N ^ WAP3205 ^ | ||
| - | | {{ media: | ||
| ===== Hardware Highlights ===== | ===== Hardware Highlights ===== | ||
| Line 25: | Line 28: | ||
| ---- | ---- | ||
| + | The NGB-419 has 16MB flash and 32MB RAM. Installation of 19.07.4 is possible and runs well. | ||
| ==== WAP3205 v1 ==== | ==== WAP3205 v1 ==== | ||
| Line 34: | Line 38: | ||
| The images for the NBG-419N are compatible with the WAP3205, as they have same hardware internally. | The images for the NBG-419N are compatible with the WAP3205, as they have same hardware internally. | ||
| - | **NOTE: | + | **NOTE: |
| ---- datatable ---- | ---- datatable ---- | ||
| Line 43: | Line 47: | ||
| filter | filter | ||
| ---- | ---- | ||
| + | |||
| ===== Installation ===== | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : c,c,c | ||
| + | filter | ||
| + | filter | ||
| + | filteror: Model=WAP3205 | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | -> [[docs: | ||
| + | |||
| - | Support appeared in r28078. | ||
| The prefered method is to build the image by yourself. See [[docs: | The prefered method is to build the image by yourself. See [[docs: | ||
| - | If you dont like to build the image by yourself, | + | If you dont like to build the image by yourself, download the OpenWrt image as shown above. |
| Unfortunately, | Unfortunately, | ||
| Line 71: | Line 87: | ||
| You choosed 2 | You choosed 2 | ||
| - | Put ...ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin to your TFTP server root (usually ''/ | + | Put '' |
| Then press Y and enter IP for your device, TFTP server and firmware image file name: | Then press Y and enter IP for your device, TFTP server and firmware image file name: | ||
| Line 86: | Line 102: | ||
| Its recommended to flash the same sysupgrade firmware file once again with the build in OpenWrt updater and to not save the settings. The TFTP in U-Boot sometimes mess up few parts in the firmware. | Its recommended to flash the same sysupgrade firmware file once again with the build in OpenWrt updater and to not save the settings. The TFTP in U-Boot sometimes mess up few parts in the firmware. | ||
| + | |||
| + | Note: Flash size is (wrongly) identified as 16MB in 19.07.4; it is only 4MB. | ||
| ===== Hardware ===== | ===== Hardware ===== | ||
| ==== Info ==== | ==== Info ==== | ||
| - | | **Architecture:** | MIPS | | + | ^ Architecture |
| - | | **Vendor:** | Ralink | + | ^ Vendor |
| - | | **Bootloader:** | [[docs: | + | ^ Bootloader |
| - | | **System-On-Chip:** | Ralink RT3052 | + | ^ System-On-Chip |
| - | | **CPU Speed:** | 384 Mhz | | + | ^ CPU Speed | 384 Mhz | |
| - | | **Flash size:** | 4 MiB | | + | ^ Flash size | 4 MiB | |
| - | | **RAM:** | 32 MiB | | + | ^ RAM | 32 MiB | |
| - | | **USB:** | No (Not populated) | + | ^ USB | No (Not populated) |
| - | | **Serial:** | [[# | + | ^ Serial |
| - | | **JTAG:** | [[# | + | ^ JTAG | [[# |
| ==== Opening the case ==== | ==== Opening the case ==== | ||
| Line 120: | Line 138: | ||
| === WAP3205 === | === WAP3205 === | ||
| {{media: | {{media: | ||
| + | |||
| + | ==== JTAG ==== | ||
| + | -> [[docs: | ||
| + | |||
| + | How to connect to the JTAG Port of this specific device:\\ | ||
| + | **Insert photo of PCB with markings for JTAG port** | ||
| ===== Bootloader ===== | ===== Bootloader ===== | ||