Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revisionBoth sides next revision
toh:zte:h218n [2021/04/06 19:06] danitooltoh:zte:h218n [2021/04/07 10:18] – images, minor changes to clarify models danitool
Line 1: Line 1:
 ====== ZTE H218N ====== ====== ZTE H218N ======
  
-{{:media:zte:h218n:zte_h218n_side_low.png?0x200|}}+{{:media:zte:h218n:zte_h218n_side_low.png?0x200|v1.1/v2.0}}
  
  
 <WRAP center round alert 60%> <WRAP center round alert 60%>
-Versions **v1.1** and **v2.0** spite labeled as **H218N** on the case they come with a **H298 board** inside, which is totally different and unsupportable (Realtek Hardware). See [[https://oldwiki.archive.openwrt.org/toh/zte/h298n]]+Versions **v1.1** and **v2.0** spite labeled as **H218N** on the case they come with a **H298N board** inside, which is totally different and unsupportable (Realtek Hardware). See [[https://oldwiki.archive.openwrt.org/toh/zte/h298n]]
  
-You can'know if they are H298 models until you open the casing. Or inspecting the stock web interface at the section **info** to see the if the version is v1.1 or v2.0+You can know the real model looking at the power connector, on H298N model is located at the left. Or inspecting the stock web interface at the section **info** to see the if the version is v1.1 or v2.0
 </WRAP> </WRAP>
  
Line 93: Line 93:
  
 ==== Photos ==== ==== Photos ====
-ZTE ZXHN H218N: 
-Sticker says ZTE ZXHN H218N, but PCB says ZTE ZXHN H298N V1.1 
  
-//Front://+=== v1 === 
 +//Front and back://
  
-{{:media:zte:h218n:zte_h218n_front_low.png?250|}}+FIXME
  
-//Back://+=== v1.1/v2.0 (H298N) === 
 +//Front and back://
  
-{{:media:zte:h218n:zte_h218n_back_low.png?250|}}+{{:media:zte:h218n:zte_h218n_front_low.png?250|}} {{:media:zte:h218n:zte_h218n_back_low.png?250|}}
  
 +Sticker says ZTE ZXHN H218N, but PCB says ZTE ZXHN H298N V1.1
  
 ==== Opening the case ==== ==== Opening the case ====
Line 110: Line 111:
   *To remove the cover, there's a screw on the base of the router. Split both halfs carerully.   *To remove the cover, there's a screw on the base of the router. Split both halfs carerully.
  
 +
 +=== v1 ===
 //Main PCB// //Main PCB//
  
-**Photo of PCB**+{{:media:zte:h218n:h218n_v1-board_top.jpg?direct&400|}} {{:media:zte:h218n:h218n_v1-board_bottom.jpg?direct&400|}} 
 + 
 +=== v1.1/v2.0 (H298N) === 
 +//Main PCB//
  
 {{:media:zte:h218n:zte_h218n_pcb_front_low.jpg?400|}}    {{:media:zte:h218n:zte_h218n_pcb_back_low.jpg?400|}} {{:media:zte:h218n:zte_h218n_pcb_front_low.jpg?400|}}    {{:media:zte:h218n:zte_h218n_pcb_back_low.jpg?400|}}
 +
 ==== Serial ==== ==== Serial ====
 -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc. -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.
  • Last modified: 2021/04/09 09:12
  • by danitool