ZLMnet F8
The ZLMnet F8 was introduced in spring 2016. The unit is delivered with OpenWrt 15.05.1 and ZLMnet's proprietary user interface on top of all the standard OpenWrt tools. Features include:
- Based on the Mediatek MT7620A @ 580MHz
- 128MB DDR2, 16MB SPI Flash
- 300Mbps Wifi N (2.4GHz only)
- Single 100M Ethernet (WAN/LAN)
- Internal antennas
- MicroSD card
- MicroSIM card
- 4G Module:Qualcomm 9×07
- Built in polymer lithium battery, capacity of about 5000mAh
Supported Versions
Hardware Highlights
Installation
Flash Layout
OEM easy installation
The ZLMnet F8 runs openwrt or OEM firmware
- Browse to http://192.168.100.1/,browse Management menu ,browse to update software
- Upload .bin file to router
- Wait for it to reboot
- Telnet to 192.168.100.1 and set a root password, or browse to http://192.168.100.1 if LuCI is installed.
OEM installation using the TFTP method
The ZLMnet F8 Uboot support TFTP server mode! Uboot restore Upgrade method:
- Set a fixed IP:192.168.100.100 on your computer.
- Connect the network cable, long press RESET button, and then boot until the circle light is always bright.
- tftp.exe -i 192.168.100.1 PUT openwrt-ramips-mt7620-f8-squashfs-sysupgrade.bin
- Please wait for a moment until the circle lights out. After the success of the upgrade, the system will automatically restart.
- If not successful, please redo the above steps.
Note: The .bin file name must be consistent with the upgrade software file name, if not, please modify ! This method is also applicable to OpenWrt upgrade.
Upgrading OpenWrt
LuCI Web Upgrade Process
- Browse to http://192.168.100.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
- Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
sysupgrade
mtd
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
mtd
If sysupgrade
does not support this router, use mtd
.
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot
Debricking
The ZLMnet F8 Uboot support TFTP server mode! Uboot restore Upgrade method:
- Set a fixed IP:192.168.100.100 on your computer.
- Connect the network cable, long press RESET button, and then boot until the circle light is always bright.
- tftp.exe -i 192.168.100.1 PUT openwrt-ramips-mt7620-f8-squashfs-sysupgrade.bin
- Please wait for a moment until the circle lights out. After the success of the upgrade, the system will automatically restart.
- If not successful, please repeat the above steps.
Note: The .bin file name must be consistent with the upgrade software file name, if not, please modify ! This method is also applicable to OpenWrt upgrade.
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Network interfaces
The default network configuration is:
Interface Name | Description | Default configuration |
---|---|---|
br-lan | LAN & WiFi | 192.168.100.1/24 |
vlan0 (eth0.0) | LAN ports | None (default) |
vlan1 (eth0.1) | WAN port | DHCP (Either-or) |
wl0 | WiFi | Disabled |
Switch Ports (for VLANs)
Port number 0 is labeled LAN/WAN,Default is LAN. Ports 1-5 are not present. Port 6 (CPU) is the internal connection to the router itself. vlan1 = eth0.1, vlan2 = eth0.2 and so on.
Port | Switch port |
---|---|
LAN | 0 (default) |
WAN | 0 (Either-or) |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
The ZLMnet F8 has the following buttons:
BUTTON | Event |
---|---|
Reset | reset |
System is running, Holding the reset button for more than 5 seconds will result in a factory reset. when holding the reset button,power on F8,will enter uboot update software mode.
Hardware
Info
Photos
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Serial connection parameters for ZLMnet F8 v1.3 | 57600, 8N1 |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
Don't support JTAG!
Bootloader mods
4G Module
Bootlogs
OEM bootlog
U-Boot 1.1.3 (Jun 22 2016 - 17:57:39) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb8000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 29 spi device id: ef 40 18 0 0 (40180000) find flash: W25Q128BV raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.2.S.1 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 1024 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 128 MBytes Flash component: SPI Flash Date:Jun 22 2016 Time:17:57:39 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =128 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. unenter reset button... 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: ZLMnet?MIFIF17N? Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5372280 Bytes = 5.1 MB Load Address: 80000000 Entry Point: 8000c310 raspi_read: from:50040 len:51f96d OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c310) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@ubuntu) (gcc version 3.4.2) #403 Tue Apr 11 04:40:21 PDT 2017 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe CPU revision is: 00019650 (MIPS 24Kc) Software DMA cache coherency Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0001b32f Readback ErrCtl register=0001b32f Memory: 120564k/131072k available (4505k kernel code, 10508k reserved, 859k data, 3688k init, 0k highmem) NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 1a311d RALINK_GPIOMODE = 18311d PPLL_CFG1=0xe48000 MT7620 PPLL lock PPLL_DRV =0x80080504 start PCIe register access RALINK_RSTCTRL = 2400000 RALINK_CLKCFG1 = 75afffc0 *************** MT7620 PCIe RC mode ************* PCIE0 no card, disable it(RST&CLK) PCIE0 enabled init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RT3xxx EHCI/OHCI init. fuse init (API version 7.15) msgmni has been set to 235 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : ef 40 18 0 0 (40180000) W25Q128BV(ef 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536 Creating 6 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000ff0000 : "Kernel" 0x000000ff0000-0x000001000000 : "Justsec" rdm_major = 253 SMACCR1 -- : 0x00002c67 SMACCR0 -- : 0xfb3a16e2 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! SMACCR1 -- : 0x00002c67 SMACCR0 -- : 0xfb3a16e2 PROC INIT OK! PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> usbcore: registered new interface driver cdc_ether === pAd = c0147000, size = 710536 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.1.6 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems MTK MSDC device init. mtk-sd: MediaTek MT6575 MSDC Driver Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1883 buckets, 7532 max) nf_conntrack_rtsp v0.6.21 loading matchsize=264 xt_time: kernel timezone is -0000 IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone TCP cubic registered NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2318> PID<kworker/u:1><0x17> Freeing unused kernel memory: 3688k freed init started: BusyBox v1.12.1 (2Algorithmics/MIPS FPU Emulator v1.5 015-10-18 23:45:48 PDT) starting pidevpts: called with bogus options d 32, tty '': '/etc_ro/rcS' Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= echo 8196 > /proc/sys/net/netfilter/nf_conntrack_max starting pid 45, tty '': '/bin/syslogc' starting pid 44, tty '/dev/ttyS1': '/bin/sh' |19700101000006.info.mesg:45|/sbin/syslogd -C -n|syslog/syslog.c:108 BusyBox v1.12.1 (2015-10-18 23:45:48 PDT) built-in shell (ash) Enter 'help' for a list of built-in commands. # killall -9 umodem & killall -9 wifi_client & killall -9 udhcpc & killall: umodem: no process killed internet.sh killall: wifi_client: no process killed killall: udhcpc: no process killed Password for 'admin' changed ##### disable 1st wireless interface ##### rmmod: rt2860v2_ap_net: No such file or directory rmmod: rt2860v2_ap: No such file or directory rmmod: rt2860v2_ap_util: No such file or directory MAC ADDRESS:3A16E0insmod: rt2860v2_ap_util.ko: module not found insmod: rt2860v2_ap.ko: module not found insmod: rt2860v2_ap_net.ko: module not found RX DESC a6ba5000 size = 2048 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 1, CalCode = 5 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffff1 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= 0, phase=3d) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 3, phase=3d) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 Main bssid = 2c:67:fb:3a:16:e0 <==== rt28xx_init, Status=0 0x1300 = 00064300 ifconfig: ioctl 0x8913 failed: No such device brctl: bridge br0: No such device or address Raeth v3.0 (Tasklet,SkbRecycle) phy_tx_ring = 0x06648000, tx_ring = 0xa6648000 phy_rx_ring0 = 0x06649000, rx_ring0 = 0xa6649000 SMACCR1 -- : 0x00002c67 SMACCR0 -- : 0xfb3a16e2 ESW: Link Status Changed - Port0 Link UP CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 vconfig: ioctl error for rem: No such device vconfig: ioctl error for rem: No such device rmmod: 8021q: No such file or directory device eth2 entered promiscuous mode ##### config Ralink ESW vlan partition (WLLLL) ##### switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=81000000 switch reg write offset=2710, value=81000000 switch reg write offset=2604, value=20ff0003 switch reg write offset=2704, value=20ff0003 Special Tag Disabled switch reg write offset=2610, value=81000000 switch reg write offset=2014, value=10001 switch reg write offset=2114, value=10001 switch reg write offset=2214, value=10001 switch reg write offset=2314, value=10001 switch reg write offset=2414, value=10002 switch reg write offset=2514, value=10001 REG_ESW_WT_device ra0 entered promiscuous mode MAC_ATC is 0x7ff0002 done. device eth2.1 entered promiscuous mode syslogd exiting process '/bin/syslogc' (pid 45) exited. Scheduling for restart. starting pid 640, tty '': '/bin/syslogc' |19700101000011.info.mesg:640|/sbin/syslogd -C -n|syslog/syslog.c:108 led=13, on=10, off=10, blinks,=4000, reset=1, time=4000 led=12, on=4000, off=1, blinks,=1, reset=1, time=4000 |19700101000011.info.mesg:656|system_dumb( ifconfig apcli0 0.0.0.0 led=12, on=10, off=10, blinks,=4000, reset=1, time=4000 up )|misc.c:70 |19700101000011.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliEnable=0 )|misc.c:70 upid = 655 br0: port 2(eth2.1) entering learning state br0: port 2(eth2.1) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state ifconfig: ioctl 0x8914 failed: Cannot assign requested address ifconfig: ioctl 0x8914 failed: Cannot assign requested address br0: port 2(eth2.1) entering forwarding state br0: port 1(ra0) entering forwarding state killall: udhcpd: no process killed Set: phy[4].reg[0] = 0800 Set: phy[1].reg[0] = 0800 Set: phy[2].reg[0] = 0800 Set: phy[3].reg[0] = 0800 728 line: retptr = newifi_2A8C |19700101000014.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliEnable=0 )|misc.c:70 |19700101000014.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliAuthMode=WPA2PSK )|misc.c:70 |19700101000014.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliEncrypType=AES )|misc.c:70 |19700101000014.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliWPAPSK=88886666 )|misc.c:70 |19700101000015.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliSsid=newifi_2A8C )|misc.c:70 |19700101000015.info.mesg:656|system_dumb( iwpriv apcli0 set Channel=1 )|misc.c:70 |19700101000015.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliEnable=1 )|misc.c:70 Port4 is up. Skip. Port1 is up. Skip. Port2 is up. Skip. Port3 is up. Skip. ifconfig: ioctl 0x8913 failed: No such device /bin/radvd.sh: line 7: cannot create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory rm: cannot remove '/etc/radvd.conf': No such file or directory killall rt2860apd 1>/dev/null 2>&1 iptables -F -t filter 1>/dev/null 2>&1 iptables -D FORWARD -j PORTSCAN 1>/dev/null 2>&1 iptables -D INPUT -j PORTSCAN 1>/dev/null 2>&1 iptables -F PORTSCAN 1>/dev/null 2>&1 iptables -D FORWARD -j PSD 1>/dev/null 2>&1 iptables -D INPUT -j PSD 1>/dev/null 2>&1 iptables -F PSD 1>/dev/null 2>&1 iptables -D FORWARD -j SHORT 1>/dev/null 2>&1 iptables -D INPUT -j SHORT 1>/dev/null 2>&1 iptables -F SHORT 1>/dev/null 2>&1 iptables -D FORWARD -j icmp_flood 1>/dev/null 2>&1 iptables -D INPUT -j icmp_flood 1>/dev/null 2>&1 iptables -F icmp_flood 1>/dev/null 2>&1 iptables -D FORWARD -j udp_flood 1>/dev/null 2>&1 iptables -D INPUT -j udp_flood 1>/dev/null 2>&1 iptables -F udp_flood 1>/dev/null 2>&1 iptables -D FORWARD -j syn_flood 1>/dev/null 2>&1 iptables -D INPUT -j syn_flood 1>/dev/null 2>&1 iptables -F syn_flood 1>/dev/null 2>&1 iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1 iptables -F macipport_filter 1>/dev/null 2>&1 iptables -D FORWARD -j web_filter 1>/dev/null 2>&1 iptables -F web_filter 1>/dev/null 2>&1 iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT iptables -P FORWARD ACCEPT iptables -t filter -N ipport_trigger 1>/dev/null 2>&1 iptables -t filter -A FORWARD -j ipport_trigger 1>/dev/null 2>&1 iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1 iptables -t nat -F port_forward 1>/dev/null 2>&1; iptables -t nat -X port_forward 1>/dev/null 2>&1 iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1 iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ 1>/dev/null 2>&1 iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1 iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1 iptables -t nat -N port_trigger 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j port_trigger 1>/dev/null 2>&1 greenap.sh init sh: greenap.sh: not found route delete 239.255.255.250 1>/dev/null 2>&1 killall wscd 1>/dev/null 2>&1 killall -9 wscd 1>/dev/null 2>&1 iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1 iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1 killall -q zebra killall -q ripd ##### USB init ##### |19700101000020.info.mesg:656|system_dumb( udhcpc -i apcli0 -s /sbin/udhcpc.sh -p /var/run/udhcpc.pid & )|misc.c:70 udhcpc (v1.12.1) started |19700101000020.info.mesg:656|system_dumb( iptables -t nat -A POSTROUTING -s 192.168.100.1/24 -o apcli0 -j MASQUERADE )|misc.c:70 led=12, on=1, off=4000, blinks,=1, reset=4000, time=1 led=13, on=1, off=4000, blinks,=1, reset=4000, time=1 |19700101000020.info.mesg:656|system_dumb( iwpriv apcli0 set ApCliEnable=0 )|misc.c:70 |19700101000020.info.mesg:656|system_dumb( killall -9 udhcpc )|misc.c:70 led=12, on=4000, off=1, blinks,=1, reset=1, time=4000 led=13, on=10, off=10, blinks,=4000, reset=1, time=4000 led=12, on=1, off=2, blinks,=4000, reset=1, time=4000 route: ioctl 0x890c failed: No such process |19700101000020.info.mesg:656|system_dumb( iptables -t nat -D POSTROUTING -s 192.168.100.1/24 -o apcli0 -j MASQUERADE )|misc.c:70 storage.sh ftp 1st partition does not exist storage.sh samba /sbin/smp.sh: line 51: cannot create /proc/irq/3/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /proc/irq/4/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /proc/irq/24/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /proc/irq/25/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /proc/irq/19/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /proc/irq/20/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /proc/irq/22/smp_affinity: nonexistent directory /sbin/smp.sh: line 51: cannot create /sys/class/net/ra0/queues/rx-0/rps_cpus: nonexistent directory /sbin/smp.sh: line 51: cannot create /sys/class/net/rai0/queues/rx-0/rps_cpus: nonexistent directory /sbin/smp.sh: line 51: cannot create /sys/class/net/eth2/queues/rx-0/rps_cpus: nonexistent directory /sbin/smp.sh: line 51: cannot create /sys/class/net/eth3/queues/rx-0/rps_cpus: nonexistent directory 1st partition does not exist webs: Listening for HTTP requests at address 192.168.100.1
OpenWrt bootlog
Starting kernel ... [ 0.000000] Linux version 3.18.27 (lamon@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49085) ) #162 Mon Feb 6 01:50:39 PST 2017 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is ZLMnet F8 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0001b320 [ 0.000000] Readback ErrCtl register=0001b320 [ 0.000000] Memory: 126208K/131072K available (2597K kernel code, 133K rwdata, 524K rodata, 192K init, 186K bss, 4864K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] pinctrl core: initialized pinctrl subsystem [ 0.100000] NET: Registered protocol family 16 [ 0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.140000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.150000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.160000] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.170000] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.180000] Switched to clocksource systick [ 0.190000] NET: Registered protocol family 2 [ 0.190000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.210000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.220000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.230000] TCP: reno registered [ 0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.250000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] NET: Registered protocol family 1 [ 0.270000] rt-timer 10000100.timer: maximum frequency is 2441Hz [ 0.290000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.310000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.340000] msgmni has been set to 246 [ 0.350000] io scheduler noop registered [ 0.350000] io scheduler deadline registered (default) [ 0.360000] ralink-usb-phy usbphy: invalid resource [ 0.370000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.390000] console [ttyS0] disabled [ 0.400000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A [ 0.410000] console [ttyS0] enabled [ 0.410000] console [ttyS0] enabled [ 0.430000] bootconsole [early0] disabled [ 0.430000] bootconsole [early0] disabled [ 0.460000] m25p80 spi32766.0: w25q128 (16384 Kbytes) [ 0.470000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.480000] Creating 4 MTD partitions on "spi32766.0": [ 0.490000] 0x000000000000-0x000000030000 : "u-boot" [ 0.500000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.510000] 0x000000040000-0x000000050000 : "factory" [ 0.520000] 0x000000050000-0x000001000000 : "firmware" [ 0.540000] Support for built-in firmware splitter will be removed, please use CONFIG_MTD_SPLIT_UIMAGE_FW [ 0.560000] 0x00000016e03f-0x000001000000 : "rootfs" [ 0.570000] mtd: device 4 (rootfs) set to be root filesystem [ 0.580000] 1 squashfs-split partitions found on MTD device rootfs [ 0.590000] 0x0000008b0000-0x000001000000 : "rootfs_data" [ 0.610000] gsw: setting port4 to ephy mode [ 0.610000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex) [ 0.630000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.650000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.660000] rt2880_wdt 10000120.watchdog: Initialized [ 0.670000] TCP: cubic registered [ 0.680000] NET: Registered protocol family 17 [ 0.690000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.710000] Bridge firewalling registered [ 0.720000] 8021q: 802.1Q VLAN Support v1.8 [ 0.750000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.770000] Freeing unused kernel memory: 192K (80330000 - 80360000) [ 3.340000] init: Console is alive [ 3.350000] init: - watchdog - [ 9.750000] usbcore: registered new interface driver usbfs [ 9.760000] usbcore: registered new interface driver hub [ 9.770000] usbcore: registered new device driver usb [ 9.790000] Button Hotplug driver version 0.4.1 [ 9.840000] SCSI subsystem initialized [ 9.850000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.870000] ehci-platform: EHCI generic platform driver [ 9.890000] phy phy-usbphy.0: remote usb device wakeup disabled [ 9.900000] phy phy-usbphy.0: UTMI 16bit 30MHz [ 9.910000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 9.920000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 9.940000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 9.970000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 9.980000] hub 1-0:1.0: USB hub found [ 9.990000] hub 1-0:1.0: 1 port detected [ 10.000000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 10.010000] ohci-platform: OHCI generic platform driver [ 10.020000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 10.040000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 10.050000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 10.120000] hub 2-0:1.0: USB hub found [ 10.130000] hub 2-0:1.0: 1 port detected [ 10.150000] MTK MSDC device init. [ 10.200000] mtk-sd: MediaTek MT6575 MSDC Driver [ 10.210000] sdhci: Secure Digital Host Controller Interface driver [ 10.220000] sdhci: Copyright(c) Pierre Ossman [ 10.230000] sdhci-pltfm: SDHCI platform and OF driver helper [ 10.250000] usbcore: registered new interface driver usb-storage [ 10.410000] init: - preinit - [ 11.640000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 11.690000] random: mktemp urandom read with 18 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 14.940000] mount_root: loading kmods from internal overlay [ 16.050000] jffs2: notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 16.090000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 16.110000] block: extroot: not configured [ 16.370000] jffs2: notice: (335) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 17.130000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 17.150000] block: extroot: not configured [ 17.160000] mount_root: switching to jffs2 overlay [ 17.210000] procd: - early - [ 17.220000] procd: - watchdog - [ 18.260000] procd: - ubus - [ 19.290000] procd: - init - Please press Enter to activate this console. [ 22.000000] NET: Registered protocol family 10 [ 22.030000] ntfs: driver 2.1.31 [Flags: R/O MODULE]. [ 22.060000] Initializing XFRM netlink socket [ 22.070000] NET: Registered protocol family 15 [ 22.080000] tun: Universal TUN/TAP device driver, 1.6 [ 22.090000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 22.110000] ipip: IPv4 over IPv4 tunneling driver [ 22.160000] l2tp_core: L2TP core driver, V2.0 [ 22.170000] l2tp_netlink: L2TP netlink interface [ 22.190000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 22.200000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 22.490000] gre: GRE over IPv4 demultiplexor driver [ 22.500000] ip_gre: GRE over IPv4 tunneling driver [ 22.520000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 22.560000] Netfilter messages via NETLINK v0.30. [ 22.580000] ip_set: protocol 6 [ 22.680000] u32 classifier [ 22.680000] input device check on [ 22.690000] Actions configured [ 22.700000] Mirror/redirect action on [ 22.720000] nf_conntrack version 0.5.0 (1975 buckets, 7900 max) [ 22.800000] fuse init (API version 7.23) [ 22.830000] arp_tables: (C) 2002 David S. Miller [ 22.860000] usbcore: registered new interface driver cdc_wdm [ 22.880000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68 [ 22.900000] Backport generated by backports.git backports-20151218-0-g2f58d9d [ 22.930000] Ebtables v2.0 registered [ 22.940000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 22.960000] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 23.000000] ctnetlink v0.93: registering with nfnetlink. [ 23.060000] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net> [ 23.120000] usbcore: registered new interface driver ums-alauda [ 23.130000] usbcore: registered new interface driver ums-cypress [ 23.150000] usbcore: registered new interface driver ums-datafab [ 23.160000] usbcore: registered new interface driver ums-freecom [ 23.180000] usbcore: registered new interface driver ums-isd200 [ 23.200000] usbcore: registered new interface driver ums-jumpshot [ 23.210000] usbcore: registered new interface driver ums-karma [ 23.230000] usbcore: registered new interface driver ums-sddr09 [ 23.240000] usbcore: registered new interface driver ums-sddr55 [ 23.260000] usbcore: registered new interface driver ums-usbat [ 23.300000] usbcore: registered new interface driver usbserial [ 23.310000] usbcore: registered new interface driver usbserial_generic [ 23.320000] usbserial: USB Serial support registered for generic [ 23.350000] xt_DNETMAP INIT successfull (version 2) [ 23.470000] xt_time: kernel timezone is -0000 [ 23.490000] usbcore: registered new interface driver cdc_ether [ 23.690000] PPP generic driver version 2.4.2 [ 23.700000] PPP MPPE Compression module registered [ 23.710000] NET: Registered protocol family 24 [ 23.720000] PPTP driver version 0.8.5 [ 23.740000] usbcore: registered new interface driver qmi_wwan [ 23.790000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 23.800000] usbcore: registered new interface driver option [ 23.810000] usbserial: USB Serial support registered for GSM modem (1-port) [ 23.870000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected [ 23.880000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 33.560000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 33.600000] device eth0.1 entered promiscuous mode [ 33.610000] device eth0 entered promiscuous mode [ 33.650000] br-lan: port 1(eth0.1) entered forwarding state [ 33.660000] br-lan: port 1(eth0.1) entered forwarding state [ 34.810000] S60samba (1619): drop_caches: 3 [ 35.660000] br-lan: port 1(eth0.1) entered forwarding state [ 45.480000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 45.540000] device wlan0 entered promiscuous mode [ 45.550000] br-lan: port 2(wlan0) entered forwarding state [ 45.560000] br-lan: port 2(wlan0) entered forwarding state [ 45.630000] br-lan: port 2(wlan0) entered disabled state [ 55.840000] br-lan: port 2(wlan0) entered forwarding state [ 55.850000] br-lan: port 2(wlan0) entered forwarding state [ 55.860000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 57.850000] br-lan: port 2(wlan0) entered forwarding state