Xiaomi Redmi AX6000

The Xiaomi Redmi AX6000 router supports 4 802.11ax streams on both 2.4GHz @40MHz and 5GHz @160MHz for a combined 6000Mbps wireless speed. It is based on the MediaTek MT7986A SoC.

Redmi AX6000

Support Forums https://forum.openwrt.org/t/add-openwrt-support-for-xiaomi-redmi-ax6000/125008

In-depth review https://www.acwifi.net/19676.html

There are currently two potential layouts for this device that are supported.

  1. Stock layout: this option retains vendor's partition scheme and ability to restore vendor firmware. On the down side, there is a bit of wasted space.
  2. U-boot mod layout: this option uses OpenWRT U-Boot with automatic TFTP recovery and optional NAND recovery options. It is also a more efficient use of available space vs the stock option. Users will not be able to revert back to the vendor firmware using this.

It should be noted that in order to use the U-boot mod layout, users must first install OpenWRT using the Stock layout which is described below.

This exploits a vulnerability in Xiaomi's set_sys_time function. Credit to forum user @remittor. Following this may result in a bricked device if you don't know what you're doing!

First, you'll need to grab a vulnerable software version. The table below shows known vulnerable versions. It is recommended to install version 1.0.48.

To downgrade: navigate to the upload firmware page and select the appropriate software version. It will complain about the downgrade. Edit the url and change the <html>0</html> at the end to a <html>1</html> and press enter. Or change to <html>2</html> if there is already <html>1</html> (seen on v1.0.64). The downgrade will proceed.

You'll see references to a {token} variable in many of the following commands. To get it, sign into the web UI of your router and look for stok=<some hex value> in the URL. This is the token. It will change after each reboot so you will need to get it after each one.

OEM UI is only in Chinese. A quick startup (tested in verion 1.0.48) would be:

From direct connected LAN port (address will be assigned by AX6000 using DHCP), access http://192.168.31.1/ portal and follow these steps (one per page):

  1. Remove second tick and click blue button
  2. Click last hyperlink below blue button
  3. Select DHCP arrow
  4. Type WiFi password (8 chars min). It'll be used for login, so make it simple. Uncheck middle tick and click blue button
  5. Go to the web UI at http://192.168.31.1/
  6. Type WiFi password (as above) in box for access.

Now you can find stok= token in URL. Repeat last two steps after each reboot to get the new one.

A computer (preferably Linux) must be connected to the router via an ethernet LAN port (one of the 3 ports in the middle).

Enable Development/Debug Mode

Xiaomi devices contain a partition called “crash”. When \xa5\x5a\x00\x00 is loaded into the partition, the router enters a “debug” or “development” mode, which allows persistent overwriting of bdata partition. This partition determines whether telnet, uart and ssh are enabled.

  1. http://192.168.31.1/cgi-bin/luci/;stok={token}/api/misystem/set_sys_time?timezone=%20%27%20%3B%20echo%20pVoAAA%3D%3D%20%7C%20base64%20-d%20%7C%20mtd%20write%20-%20crash%20%3B%20 writes the magic bytes to the crash partition. The command being run on the router is echo pVoAAA== | base64 -d | mtd write - crash.
  2. http://192.168.31.1/cgi-bin/luci/;stok={token}/api/misystem/set_sys_time?timezone=%20%27%20%3b%20reboot%20%3b%20 reboots the device.

Set Bdata

Changing the telnet_en, ssh_en and uart_en in bdata will allow persistent access to the device.

  1. http://192.168.31.1/cgi-bin/luci/;stok={token}/api/misystem/set_sys_time?timezone=%20%27%20%3B%20bdata%20set%20telnet_en%3D1%20%3B%20bdata%20set%20ssh_en%3D1%20%3B%20bdata%20commit%20%3B%20 sets telnet, ssh and uart to enabled (you should now see the full bootlog on the uart console if you have it connected). It runs bdata set telnet_en=1 ; bdata set ssh_en=1 ; bdata commit on the router.
  2. http://192.168.31.1/cgi-bin/luci/;stok={token}/api/misystem/set_sys_time?timezone=%20%27%20%3b%20reboot%20%3b%20 reboots the device.

Disable Development/Debug Mode

Sometimes features break if development/debug mode is left on. Let's disable it (access will still be permitted).

  1. http://192.168.31.1/cgi-bin/luci/;stok={token}/api/misystem/set_sys_time?timezone=%20%27%20%3b%20mtd%20erase%20crash%20%3b%20 erases the crash partition by running mtd erase crash on the router.

Now you can telnet into your device!

Enable ssh access

Booting to the recommended version of Xiaomi firmware leaves ssh (via dropbear) broken. To fix, telnet into the device, then edit /etc/init.d/dropbear deleting the three lines:

if [ "$flg_ssh" != "1" -o "$channel" = "release" ]; then        
  return 0                                                           
fi

If you want, you can directly paste this command in the connected terminal without the need of editing:

cd /etc/init.d/ && rm -rf dropbear && curl https://gist.githubusercontent.com/AmirulAndalib/4046f133f66b100d9bf2156dfd84afe8/raw/dropbear >> dropbear && chmod +x dropbear && cd ~

Gist revision: https://gist.github.com/AmirulAndalib/4046f133f66b100d9bf2156dfd84afe8/revisions#diff-17d1edd22e2221c5ceeb5641c97a8725222084d4f3d784f17d1c19638b7cc871L135-L137

Now start the daemon: /etc/init.d/dropbear start

If needed (by default it's empty), root password can be changed typing passwd

A note about recent ssh clients

Recent ssh clients will not be able to connect due to the old version dropbear using deprecated keys. To work around this, on the device connecting to the AX6000, edit ~/.ssh/config adding:

Host 192.168.31.1
  HostKeyAlgorithms=+ssh-rsa

It should also be noted that users of a modern ssh package will need to append the -O flag to invocations of scp in order to get it to use the legacy protocol.

% scp -O openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-stock-initramfs-factory.ubi root@192.168.31.1:/tmp

1. Once you've gained access to OEM system, check current stock system

cat /proc/cmdline

Sample OUTPUT:

console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1

if firmware=1, current system is ubi1

if firmware=0, current system is ubi0

2. Setup nvram if current system is ubi1, please setup: next time it would boot from ubi

nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit

else if current system is ubi, please setup: next time it would boot from ubi1

nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit

3. Flash flash initramfs-factory.ubi if firmware=1, current system is ubi1, flash to ubi:

ubiformat /dev/mtd8 -y -f /tmp/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-stock-initramfs-factory.ubi

if firmware=0, current system is ubi, flash to ubi1:

ubiformat /dev/mtd9 -y -f /tmp/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-stock-initramfs-factory.ubi

NOTE: If you want to go directly to the ubootmod version and you know what you're doing (high risk of bricking) you can use ubootmod initramfs version here and jump directly to step 4 of ubootmod installation instructions below. Backup of system partitions (step 2 below) is always recommended.

NOTE: Firmware could be found at https://downloads.openwrt.org/releases/{version}/targets/mediatek/filogic/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-stock-initramfs-factory.ubi

4. Reboot and setup uboot-env

It should boot to the openwrt initramfs system now, login ssh and setup:

fw_setenv boot_wait on
fw_setenv uart_en 1
fw_setenv flag_boot_rootfs 0
fw_setenv flag_last_success 1
fw_setenv flag_boot_success 1
fw_setenv flag_try_sys1_failed 8
fw_setenv flag_try_sys2_failed 8
fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),30720k(ubi),30720k(ubi1),51200k(overlay)"

here set flag_last_success=1 and flag_try_sys1_failed >= 6 and flag_try_sys1_failed >=6, to make it always boot from system 0

5. Flash sysupgrade.bin via sysupgrade

sysupgrade -n /tmp/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-stock-squashfs-sysupgrade.bin,

OpenWrt (stock layout) will be ready.

If you want to stay in this layout, you're done. If you want to move to ubootmod layout, keep reading.

1. Your device should already running OpenWrt (stock layout) as per above instructions

2. Backup BL2, Nvram, Bdata, Factory and FIP in case you break something or you want to go back to stock firmware one day.

cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin

And save all whose bin files to somewhere safe.

Then backup your configurations, since ubiformat for entire mtd device is required to create new ubootenv volume for OpenWrt U-Boot.

3. Run the following cmd to boot into an initramfs with the new OpenWrt U-Boot layout that expand ubi partion to the end of flash:

ubiformat /dev/mtd7 -y -f /tmp/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-initramfs-factory.ubi

NOTE: The firmware could be found at https://downloads.openwrt.org/releases/{version}/targets/mediatek/filogic/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-initramfs-factory.ubi

4. Reboot. It'll boot into initramfs, check mtd partion info.

The ubi partion should be mtd5

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi

5. Load kmod-mtd-rw to temporarily make the bootloader partitions writable.

The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory by default.

If you're building your own image, remember to add kmod-mtd-rw module in Kernel modules > Other modules

To install kmod-mtd-rw via opkg:

opkg update && opkg install kmod-mtd-rw

Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually e.g: https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/

Select your OpenWrt release version and kernel version accordingly.

Load kmod-mtd-rw:

insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

6. Run the following cmd to clean all pending crash dumps in pstore, or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.

rm -f /sys/fs/pstore/*

7. Format ubi and create new ubootenv volume:

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB

8. This is optional. Skip this if you do not want to have NAND recovery boot feature offered by OpenWrt U-Boot. Don't worry, you always have automatic tftp recovery feature enabled.

If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb

NOTE: The file could be found at https://downloads.openwrt.org/releases/{version}/targets/mediatek/filogic/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-initramfs-recovery.itb

9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.

mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP

NOTE: The files could be found at https://downloads.openwrt.org/releases/{version}/targets/mediatek/filogic/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-bl31-uboot.fip and https://downloads.openwrt.org/releases/{version}/targets/mediatek/filogic/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-preloader.bin

10. Flash the squashfs-sysupgrade.bin as usual:

sysupgrade -n /tmp/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-squashfs-sysupgrade.itb

NOTE: The file could be found at https://downloads.openwrt.org/releases/{version}/targets/mediatek/filogic/openwrt-{version}-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-squashfs-sysupgrade.itb

Flash layout running OEM & OpenWrt stock Firmwares

dev start end size erasesize name size
mtd0 00000000 00100000 00100000 00020000 BL2 1MiB
mtd1 00100000 00140000 00040000 00020000 Nvram 256KiB
mtd2 00140000 00180000 00040000 00020000 Bdata 256KiB
mtd3 00180000 00380000 00200000 00020000 Factory 2MiB
mtd4 00380000 00580000 00200000 00020000 FIP 2MiB
mtd5 00580000 005c0000 00040000 00020000 crash 256KiB
mtd6 005c0000 00600000 00040000 00020000 crash_log 256KiB
mtd7 00600000 02400000 01E00000 00020000 ubi 30MiB
mtd8 02400000 04200000 01E00000 00020000 ubi1 30MiB
mtd9 04200000 07400000 03200000 00020000 overlay 50MiB

Flash layout running OpenWrt ubootmod Firmware

dev start end size erasesize name size
mtd0 00000000 00100000 00100000 00020000 BL2 1MiB
mtd1 00100000 00140000 00040000 00020000 Nvram 256KiB
mtd2 00140000 00180000 00040000 00020000 Bdata 256KiB
mtd3 00180000 00380000 00200000 00020000 Factory 2MiB
mtd4 00380000 00580000 00200000 00020000 FIP 2MiB
mtd5 00580000 08000000 07A80000 00020000 ubi 122MiB

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

  • Browse to http://192.168.1.1/Upgrade.asp
  • Upload .bin file to router
  • Wait for it to reboot
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/openwrt-mediatek-filogic-xiaomi_redmi-router-ax6000-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-mediatek-filogic-xiaomi_redmi-router-ax6000-squashfs-sysupgrade.bin

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

generic.debrick

Assume that you have installed OpenWrt with stock layout, with original u-boot:

  • Connect to router via UART
  • Select Load Image in the u-boot
  • Set start address to 0x48000000, then set TFTP parameters to load the initramfs-kernel.bin.
  • Start the loaded kernel, then perform sysupgrade on OpenWrt.

If you have installed OpenWrt with u-boot mode layout, you can still use above UART recovery procedure, but u-boot will also look for a file called openwrt-mediatek-filogic-xiaomi_redmi-router-ax6000-ubootmod-initramfs-recovery.itb in a tftp server at IP address 192.168.1.254

If you provide that file in a tftp server, it'll be automatically loaded and run, so system can be recovered without using a UART connection.

Redmi AX6000 can be recovered from a soft-brick with TFTP. The flow is:

  • The router boots and asks for an IP address on the LAN ports via DHCP
  • The TFTP server assigns an IP address to the router
  • The router then connects to the TFTP server (where your DHCP server listen, e.g.: 192.168.31.100) and tries to download a file named with the IP address given by the DHCP server converted to hexadecimal.

Because of this quirk we will have to configure the tftp server to assign only one IP and we will set the file name to the only IP address it can receive.

For Windows you can use tftpd64 and on Linux you can use dnsmasq. These are the steps to do it for Linux (this can be adapted to the tftpd64's graphical interface very easily):

  • Create a folder somewhere to place your firmware for the tftp server and download the OEM firmware (the file name is a very important part; depending on the previously installed Xiaomi firmware version, you may need to adjust the name of the .img file to a different one. The router will be looking for a specific file name on the tftp server – if the requested file in the terminal does not match the one you have in the tmp folder, rename it accordingly and proceed again):
    mkdir -p /tmp/tftp
    wget https://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/rb06/miwifi_rb06_firmware_847e9_1.0.48.bin -O /tmp/tftp/C0A81F02.img
  • To ensure that the TFTP server has access to the firmware, set the privileges:
    sudo chmod -R 755 /tmp/tftp
    sudo chown -R nobody:nogroup /tmp/tftp
  • Obtain the name of the ethernet adapter (to be used in further steps):
    ip link
  • The result will loke something like (in this case, the name of the ethernet adapter is enp2s0):
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
        link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    2: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
        link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff
    3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DORMANT group default qlen 1000
        link/ether yy:yy:yy:yy:yy:yy brd ff:ff:ff:ff:ff:ff
  • Set a static address on your PC to serve the firmware from:
    sudo ip address flush dev <adapter name>
    sudo ip address add 192.168.31.100/24 dev <adapter name>
  • Run the server with the following command:
    sudo dnsmasq --no-daemon --listen-address=192.168.31.100 --bind-interfaces --dhcp-range=192.168.31.2,192.168.31.254 --enable-tftp --tftp-root=/tmp/tftp --log-dhcp --log-facility=-
  • Unplug the power, press and hold the reset button, plug the power back while still holding the button.
    • Hold the reset button until the router's LED starts flashing orange.
    • then it goes solid orange again, release the button.
    • If in the terminal, you see that the router requests a different firmware file (different name), rename the .img file in the tmp folder accordingly and repeat the procedures from the IP flush again.
  • When the device finished loading the firmware, the led starts flashing with orange (amber) light. Wait for until blue led to goes solid!
    • It might take some time for the led to go solid blue
    • If the recovery doesn't accept the downloaded file the led switches to solid white - if this is the case, restart the recovery process with other file
    • If the led is blinking blue led it means the device was flashed successfully and can be restarted
  • Put your interface back to DHCP mode and start again with breaking your device

Using official Xiaomi Recovery Tool

  1. Windows only
  2. Automates the process of setting network interface, setting TFTP server

https://bigota.miwifi.com/xiaoqiang/tools/MIWIFIRepairTool.x86.zip

Youtube tutorial with AX6S in Chinese: https://www.youtube.com/watch?v=XBaR9t-UndI

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
lanX (eth0) LAN ports (2 to 4) None
wan (eth0) WAN port DHCP
phy0-ap0 WiFi 2.4G Disabled
phy1-ap0 WiFi 5G Disabled

Numbers 2-4 are Ports 1-3 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 0 is the internal connection to the router itself.

Port Switch port
LAN 2 1
LAN 3 2
LAN 4 3
Internet (WAN) 4

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The Xiaomi Redmi AX6000 has the following buttons:

BUTTON Event
Reset reset
Mesh BTN_9

There are several LED arrays whose colors can be customized using started RBG numbers, namely:

/sys/class/leds/rgb:network/multi_intensity
/sys/class/leds/rgb:status/multi_intensity

For example, setting the status to indigo:

# echo '75 0 130' > /sys/class/leds/rgb:status/multi_intensity

To keep modifications across reboots, simply append a line to <html>/etc/rc.local</html>

[[ -f /sys/class/leds/rgb:status/multi_intensity ]] && echo '75 0 130' > /sys/class/leds/rgb:status/multi_intensity

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

  1. Remove 4 rubber feet on the bottom of the device
  2. Use a Phillips screwdriver to remove the 4 screws
  3. A tiny flathead or plastic pry tool can be wedged in between the bottom case by the antennas. Gently push and slide it along the groove and it will pop open.

Main PCB:
Insert photo of PCB

port.serial general information about the serial port, serial port cable, etc.

Once the case has been removed, locate the serial port: with the antennae facing up, the headers are in the upper-right section of the board just above the heatsink

Serial connection parameters
for Xiaomi Redmi AX6000
115200, 8N1, 3.3V

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

None so far.

The OEM bootlog provided below has been captured on a Bdata-modified device to enable UART and Telnet. An unmodified version will cut the bootlog short.

F0: 102B 0000 FA: 1040 0000 FA: 1040 0000 [0200] F9: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 2400 0041 [0000] G0: 1190 0000 EC: 0000 0000 [1000] T0: 0000 022F [010F] Jump to BL NOTICE: BL2: v2.6(release):2598dbc2a6-dirty NOTICE: BL2: Built : 13:34:54, Mar 12 2022 INFO: BL2: Doing platform setup NOTICE: WDT: disabled NOTICE: CPU: MT7986 (2000MHz) NOTICE: EMI: Using DDR4 settings before ctrl3 = 0x0 clear request & ack after ctrl3 = 0x0 DVFSRC_SUCCESS 0 dump drm registers data: 1001d000 | 00000000 00000000 00000000 00000000 1001d010 | 00000000 00000000 00000000 00000000 1001d020 | 00000000 00000000 00000000 00000000 1001d030 | 00a083f1 000003ff 00100000 00000000 1001d040 | 00000000 00000000 00020303 000000ff 1001d050 | 00000000 00000000 00000000 00000000 1001d060 | 00000002 00000000 00000000 00000000 drm: 500 = 0x8 toprgu: 80 = 0x0 [DDR Reserve] ddr reserve mode not be enabled yet Save DRM_DEBUG_CTL(0xa083f1) DRM_LATCH_CTL : 0x27e71 DRM_LATCH_CTL2: 0x200a0 drm_update_reg: 1, bits: 0x8000, addr: 0x1001d030, val: 0xa083f1 drm_update_reg: 0, bits: 0x80000, addr: 0x1001d030, val: 0xa083f1 drm_update_reg: 0, bits: 0x200, addr: 0x1001d034, val: 0x1ff drm_update_reg: 0, bits: 0x200000, addr: 0x1001d034, val: 0x1ff drm_update_reg: 0, bits: 0x100, addr: 0x1001d034, val: 0xff MTK_DRM_DEBUG_CTL : 0xa083f1 MTK_DRM_DEBUG_CTL2: 0xff drm_update_reg: 0, bits: 0x4000, addr: 0x1001d030, val: 0xa083f1 DRM DDR reserve mode FAIL! a083f1 DDR RESERVE Success 0 drm_update_reg: 0, bits: 0x2000, addr: 0x1001d030, val: 0xa083f1 drm_update_reg: 0, bits: 0x1000, addr: 0x1001d030, val: 0xa083f1 [DRAM] into mt_set_emi [EMI] ComboMCP not ready, using default setting Init_DRAM:2139: init PCDDR4 dram Start [MD32_INIT] in c code >>>>>> [MD32_INIT] 3 [MD32_INIT] 4 [MD32_INIT] 5 [MD32_INIT] 6 [MD32_INIT] V22 add 1 [MD32_INIT] V22 add 1 end [MD32_INIT] 7 [MD32_INIT] 8 [MD32_INIT] 9 [MD32_INIT] 10 [MD32_INIT] 11 [MD32_INIT] 12 [MD32_INIT] 13 [MD32_INIT] 14 [MD32_INIT] 15 [MD32_INIT] 16 [MD32_INIT] 17 [MD32_INIT] 18 [MD32_INIT] 19 [MD32_INIT] 20 [MD32_INIT] 21 [MD32_INIT] 22 [MD32_INIT] 23 [MD32_INIT] 28 [MD32_INIT] 29 [MD32_INIT] 30 for RTMRW, if have [MD32_INIT] in c code <<<<<< [Set_DRAM_Pinmux_Sel] DRAMPinmux = 0 [Bian_co] ETT version 0.0.0.1 dram_type 4, R0 cbt_mode 0, R1 cbt_mode 0 VENDOR=136 Read voltage for 1600, 0 Vio18 = 0 Vcore = 0 Vdram = 0 Vddq = 0 Vmddr = 0 == DRAMC_CTX_T == support_channel_num: 1 channel: 0 support_rank_num: 1 rank: 0 freq_sel: 22 shu_type: 0 dram_type: 4 dram_fsp: 0 odt_onoff: 1 DBI_R_onoff: 0, 0 DBI_W_onoff: 0, 0 data_width: 16 test2_1: 0x55000000 test2_2: 0xaa000100 frequency: 1600 freqGroup: 1600 u1PLLMode: 0 dram type 6 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== OCD DRVP=0 ,CALOUT=0 OCD DRVP=1 ,CALOUT=0 OCD DRVP=2 ,CALOUT=0 OCD DRVP=3 ,CALOUT=0 OCD DRVP=4 ,CALOUT=0 OCD DRVP=5 ,CALOUT=0 OCD DRVP=6 ,CALOUT=0 OCD DRVP=7 ,CALOUT=0 OCD DRVP=8 ,CALOUT=0 OCD DRVP=9 ,CALOUT=1 OCD DRVP calibration OK! DRVP=9 OCD DRVN=0 ,CALOUT=1 OCD DRVN=1 ,CALOUT=1 OCD DRVN=2 ,CALOUT=1 OCD DRVN=3 ,CALOUT=1 OCD DRVN=4 ,CALOUT=1 OCD DRVN=5 ,CALOUT=1 OCD DRVN=6 ,CALOUT=0 OCD DRVN calibration OK! DRVN=6 [SwImpedanceCal] DRVP=9, DRVN=6 freq_region=0, Reg: DRVP=11, DRVN=8, ODTP=6 MEM_TYPE=6, freq_sel=22 [ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:=================================== PCDDR4 DRAM CONFIGURATION =================================== CWL = 0x7 RTT_NORM = 0x6 CL = 0xb AL = 0x0 BL = 0x0 RBT = 0x0 WR = 0x8 =================================== =================================== ANA top config =================================== ASYNC_MODE = 3 DLL_ASYNC_EN = 1 ALL_SLAVE_EN = 0 NEW_RANK_MODE = 0 DLL_IDLE_MODE = 1 LP45_APHY_COMB_EN = 1 TX_ODT_DIS = 0 NEW_8X_MODE = 0 =================================== =================================== data_rate = 3200 CKR = 1 DQ_P2S_RATIO = 8 =================================== CA_P2S_RATIO = 8 DQ_CA_OPEN = 0 DQ_SEMI_OPEN = 0 CA_SEMI_OPEN = 0 CA_FULL_RATE = 0 DQ_CKDIV4_EN = 0 CA_CKDIV4_EN = 0 CA_PREDIV_EN = 0 PH8_DLY = 31 SEMI_OPEN_CA_PICK_MCK_RATIO= 0 DQ_AAMCK_DIV = 4 CA_AAMCK_DIV = 4 CA_ADMCK_DIV = 4 DQ_TRACK_CA_EN = 0 CA_PICK = 1600 CA_MCKIO = 1600 MCKIO_SEMI = 0 PLL_FREQ = 3200 DQ_UI_PI_RATIO = 32 CA_UI_PI_RATIO = 0 =================================== =================================== memory_type:PCDDR4 GP_NUM : 1 SRAM_EN : 1 MD32_EN : 0 =================================== =========================================== HW_ZQCAL_config =========================================== ZQCALL is 0 TZQLAT is 27 ZQCSDUAL is 0 ZQCSCNT is 511 =========================================== [ANA_INIT] >>>>>>>>>>>>>> [ANA_ClockOff_Sequence] flow start WLY_DEBUG::ANA_ClockOff_Sequence delay 100ns start WLY_DEBUG::ANA_ClockOff_Sequence delay 100ns end [ANA_ClockOff_Sequence] flow end ============ PULL DRAM RESETB DOWN ============ ========== PULL DRAM RESETB DOWN end ========= ============ SUSPEND_ON ============ ============ SUSPEND_ON end ============ ============ SPM_control ============ ============ SPM_control end ============ <<<<<< [CONFIGURE PHASE]: ANA_TX >>>>>> [CONFIGURE PHASE][SHUFFLE]: PLL =================================== data_rate = 3200,PCW = 0X7800 =================================== <<<<<< [CONFIGURE PHASE][SHUFFLE]: PLL INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x0 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 >>>>>> [CONFIGURE PHASE][SHUFFLE]: ANA CLOCK DIV configuration INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 PH8_DLY= 0x1f INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 PH8_DLY= 0x1f INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 PH8_DLY= 0x1f INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 PH8_DLY= 0x1f <<<<<< [CONFIGURE PHASE][SHUFFLE]: ANA CLOCK DIV configuration >>>>>> [CONFIGURE PHASE][SHUFFLE]: DLL INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x61 <<<<<< [CONFIGURE PHASE][SHUFFLE]: DLL [ANA_INIT] flow start [ANA_INIT] PLL >>>>>>>> [ANA_INIT] PLL <<<<<<<< [ANA_INIT] MIDPI >>>>>>>> [ANA_INIT] MIDPI <<<<<<<< [ANA_INIT] DLL >>>>>>>> [ANA_INIT] DLL <<<<<<<< [ANA_INIT] flow end [ANA_INIT] <<<<<<<<<<<<< [Flow] [DDRPHY] DIG_CONFIG_NONSHUF_DCM <<<<< [Flow] [DDRPHY] DIG_CONFIG_NONSHUF_DCM <<<<< [Flow] Enable top DCM control >>>>> [Flow] Enable top DCM control <<<<< Enable DLL master slave shuffle ============================================================== Gating Mode config ============================================================== Config description: RX_GATING_MODE 0: Pulse Mode 1: Burst Mode(8UI) 2: Burst Mode(7UI) 3: Original Burst Mode RX_GATING_TRACK_MODE 0: Valid DLY Mode 1: Valid Mode (Jade-like) 2: FIFO mode SELPH_MODE 0: By rank 1: By Phase ============================================================== GAT_TRACK_EN = 1 RX_GATING_MODE = 2 RX_GATING_TRACK_MODE = 2 SELPH_MODE = 1 PICG_EARLY_EN = 1 VALID_LAT_VALUE = 0 ============================================================== Enter into Gating configuration >>>> Exit from Gating configuration <<<< [DIG_HW_NONSHUF_ZQCAL_CFG],Configuration Enter [DIG_HW_NONSHUF_ZQCAL_CFG_FOR_PCDDR],Configuration Enter [DIG_HW_NONSHUF_ZQCAL_CFG],Configuration Enter [DIG_HW_NONSHUF_ZQCAL_CFG_FOR_PCDDR],Configuration Enter Enter into PICG configuration >>>> Exit from PICG configuration <<<< [DIG_SHUF_CONFIG] DCM_FUNCTION >>>>>>, group_id=0 [DIG_SHUF_CONFIG] DCM_FUNCTION <<<<<<, group_id=0 [DIG_FREQ_CONFIG][TX_CA][Delay] ch_id:0, group_id:0 >>>>> [DIG_FREQ_CONFIG][TX_CA][Delay] ch_id:0, group_id:0 <<<<< [DIG_HW_SHUF_ZQCAL_CFG] Group:0, Configuration Enter [ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:=================================== PCDDR4 DRAM CONFIGURATION =================================== CWL = 0x7 RTT_NORM = 0x6 CL = 0xb AL = 0x0 BL = 0x0 RBT = 0x0 WR = 0x8 =================================== [ReadLatency GET] MR_CL:[ReadLatency GET] MR_CL:UI_MCK_least is 1 RX_GW_selph_by_ps[0] is 12464 RX_GW_selph_by_ps[1] is 12464 RX_GW_selph_by_ps[2] is 12464 RX_GW_selph_by_ps[3] is 12464 =================================== RX_path CONFIGURATION =================================== data_rate is 3200 dq_p2s_ratio is 8 ca_default_delay is 1 ca_ser_latency is 7 cs2RL_start is 1 byte_num is 2 rank_num is 2 RL[0] is 24 RL[1] is 24 RL_min is 24 RL_max is 24 TDQSCK[0] is 0 TDQSCK[1] is 0 TDQSCK[2] is 0 TDQSCK[3] is 0 dqsien_default_delay is 0 dqsien_ser_latency is 7 oe_ser_latency is 4 gating_window_ahead_dqs is 2 aphy_slice_delay is 11 aphy_dtc_delay is 100 aphy_lead_lag_margin is 16 dram_ui_ratio is 2 dq_ui_unit is 312 ca_ui_unit is 312 MCK_unit is 2496 dramc_dram_ratio is 4 CKR is 1 tRPRE_toggle is 0 tRPRE_static is 2 tRPST is 0 DQSIENMODE is 1 BL is 16 FAKE_1TO16_MODE is 0 SVA_1_10_t2_SPEC is 11 read_cmd_out is 1 ca_MCKIO_ui_unit is 312 ca_p2s_ratio is 8 TDQSCK_min_SPEC is 0 TDQSCK_max_SPEC is 360 TX_pipeline is 1 RX_pipeline is 1 NEW_RANK_MODE is 0 close_loop_mode is 1 =================================== =================================== RX_path RG value =================================== RX_UI_P0[0] is 15 RX_UI_P0[1] is 15 RX_UI_P0[2] is 15 RX_UI_P0[3] is 15 RX_UI_P1[0] is 19 RX_UI_P1[1] is 19 RX_UI_P1[2] is 19 RX_UI_P1[3] is 19 RX_PI[0] is 31 RX_PI[1] is 31 RX_PI[2] is 31 RX_PI[3] is 31 DQSINCTL is 3 DATLAT_DSEL is 11 DATLAT is 12 DATLAT_DSEL_PHY is 12 DLE_EXTEND is 1 RX_IN_GATE_EN_HEAD is 0 RX_IN_GATE_EN_TAIL is 0 RX_IN_BUFF_EN_HEAD is 2 RX_IN_BUFF_EN_TAIL is 0 RX_IN_GATE_EN_PRE_OFFSET is 2 RANKINCTL_ROOT1 is 1 RANKINCTL is 1 RANKINCTL_STB is 2 RANKINCTL_RXDLY is 0 SHU_GW_THRD_POS is 42 SHU_GW_THRD_NEG is 0 RDSEL_TRACK_EN is 0 RDSEL_HWSAVE_MSK is 1 DMDATLAT_i is 12 RODTEN is 0 RODT is 1541211177 RODTE is 1 RODTE2 is 1 ODTEN_MCK_P0[4] is 0 ODTEN_MCK_P1[4] is 0 ODTEN_UI_P0[4] is 0 ODTEN_UI_P1[4] is 0 RX_RANK_DQS_LAT is 0 RX_RANK_DQ_LAT is 1 RANKINCTL_PHY is 5 RANK_SEL_LAT_CA is 0 RANK_SEL_LAT_B0 is 0 RANK_SEL_LAT_B1 is 0 RANK_SEL_STB_EN is 0 RANK_SEL_RXDLY_TRACK is 0 RANK_SEL_STB_TRACK is 1 RANK_SEL_STB_PHASE_EN is 1 RANK_SEL_PHSINCTL is 2 RANK_SEL_STB_UI_MINUS is 2 RANK_SEL_STB_UI_PLUS is 0 RANK_SEL_MCK_P0 is 0 RANK_SEL_UI_P0 is 0 RANK_SEL_MCK_P1 is 1 RANK_SEL_UI_P1 is 0 R0DQSIENLLMTEN is 1 R0DQSIENLLMT is 96 R0DQSIENHLMTEN is 1 R0DQSIENHLMT is 63 R1DQSIENLLMTEN is 1 R1DQSIENLLMT is 96 R1DQSIENHLMTEN is 1 R1DQSIENHLMT is 63 DQSIEN_FIFO_DEPTH_HALF is 1 =================================== [ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:=================================== PCDDR4 DRAM CONFIGURATION =================================== CWL = 0x7 RTT_NORM = 0x6 CL = 0xb AL = 0x0 BL = 0x0 RBT = 0x0 WR = 0x8 =================================== [WriteLatency GET] MR_CWL:[WriteLatency GET] MR_CWL:===================================== print TX_path_config ===================================== data_ratio is 3200 dq_p2s_ratio is 8 cs2WL_start is 1 byte_num is 2 rank_num is 2 CKR is 1 DBI_WR is 0 dly_1T_by_FDIV2 is 0 WL[0] is 20 WL[1] is 20 TDQSS[0][0] is 156 TDQSS[0][1] is 156 TDQSS[1][0] is 156 TDQSS[1][1] is 156 TDQS2DQ[0][0] is 0 TDQS2DQ[0][1] is 0 TDQS2DQ[1][0] is 0 TDQS2DQ[1][1] is 0 ca_p2s_ratio is 8 ca_default_dly is 1 ca_default_pi is 0 ca_ser_latency is 7 dqs_ser_laterncy is 7 dqs_default_dly is 5 dqs_oe_default_dly is 2 dq_ser_laterncy is 7 MCK_unit is 2496 dq_ui_unit is 312 ca_unit is 312 ca_MCKIO_unit is 312 ca_frate is 0 TX_ECC is 0 TWPRE is 4 OE_pre_margin is 400 OE_pst_margin is 500 OE_downgrade is 1 aphy_slice_dly is 11 aphy_dtc_dly is 100 aphy_tx_dly is 16 DDRPHY_CLK_EN_COMB_TX_OPT is 1 NEW_RANK_MODE is 0 close_loop_mode is 1 TXP_WORKAROUND_OPT is 0 ui2pi_ratio is 32 XRTW2W_PI_mute_time is 7 fake_mode is 0 =========================================== TX_DQ_UI_OE_pre is 2 TX_DQS_UI_OE_pre is 1 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 =========================================== print TX_path_attribution =========================================== TX_DQ_MCK_OE[0][0] is 2 TX_DQ_MCK_OE[0][1] is 2 TX_DQ_MCK_OE[1][0] is 2 TX_DQ_MCK_OE[1][1] is 2 TX_DQ_UI_OE[0][0] is 6 TX_DQ_UI_OE[0][1] is 6 TX_DQ_UI_OE[1][0] is 6 TX_DQ_UI_OE[1][1] is 6 TX_DQ_MCK[0][0] is 3 TX_DQ_MCK[0][1] is 3 TX_DQ_MCK[1][0] is 3 TX_DQ_MCK[1][1] is 3 TX_DQ_UI[0][0] is 2 TX_DQ_UI[0][1] is 2 TX_DQ_UI[1][0] is 2 TX_DQ_UI[1][1] is 2 TX_DQ_PI[0][0] is 0 TX_DQ_PI[0][1] is 0 TX_DQ_PI[1][0] is 0 TX_DQ_PI[1][1] is 0 TX_DQ_UIPI_all[0][0] is 0 TX_DQ_UIPI_all[0][1] is 0 TX_DQ_UIPI_all[1][0] is 0 TX_DQ_UIPI_all[1][1] is 0 TX_DQ_dlyline[0][0] is 0 TX_DQ_dlyline[0][1] is 0 TX_DQ_dlyline[1][0] is 0 TX_DQ_dlyline[1][1] is 0 TX_DQS_MCK_OE[0][0] is 2 TX_DQS_MCK_OE[0][1] is 2 TX_DQS_MCK_OE[1][0] is 2 TX_DQS_MCK_OE[1][1] is 2 TX_DQS_UI_OE[0][0] is 6 TX_DQS_UI_OE[0][1] is 6 TX_DQS_UI_OE[1][0] is 6 TX_DQS_UI_OE[1][1] is 6 TX_DQS_MCK[0][0] is 3 TX_DQS_MCK[0][1] is 3 TX_DQS_MCK[1][0] is 3 TX_DQS_MCK[1][1] is 3 TX_DQS_UI[0][0] is 1 TX_DQS_UI[0][1] is 1 TX_DQS_UI[1][0] is 1 TX_DQS_UI[1][1] is 1 DDRPHY_CLK_EN_COMB_TX_OPT is 1 TX_DQS_PI[0][0] is 16 TX_DQS_PI[0][1] is 16 TX_DQS_PI[1][0] is 16 TX_DQS_PI[1][1] is 16 DDRPHY_CLK_EN_COMB_TX_PICG_CNT is 2 DDRPHY_CLK_EN_COMB_TX_DQS_SEL_P0 is 3 DDRPHY_CLK_EN_COMB_TX_DQS_SEL_P1 is 4 DDRPHY_CLK_EN_COMB_TX_DQ_RK0_SEL_P0 is 3 DDRPHY_CLK_EN_COMB_TX_DQ_RK0_SEL_P1 is 4 DDRPHY_CLK_EN_COMB_TX_DQ_RK1_SEL_P0 is 3 DDRPHY_CLK_EN_COMB_TX_DQ_RK1_SEL_P1 is 4 DPHY_TX_DCM_EXTCNT is 0 TX_PI_UPD_MODE is 1 TX_PI_UPDCTL_B0 is 0 TX_PI_UPDCTL_B1 is 0 TX_RANKINCTL_ROOT is 0 TX_RANKINCTL is 1 TX_RANKINCTL_TXDLY is 2 DDRPHY_CLK_DYN_GATING_SEL is 5 DDRPHY_CLK_EN_OPT is 1 ARPI_CMD is 0 TDMY is 9 TXOEN_AUTOSET_DQ_OFFSET is 3 TXOEN_AUTOSET_DQS_OFFSET is 3 TXOEN_AUTOSET_EN is 1 TXPICG_AUTOSET_OPT is 0 TXPICG_AUTOSET_EN is 1 TXPICG_DQ_MCK_OFFSET_LAG is 0 TXPICG_DQS_MCK_OFFSET_LAG is 0 TXPICG_DQ_UI_OFFSET_LEAD is 0 TXPICG_DQ_UI_OFFSET_LAG is 1 TXPICG_DQS_UI_OFFSET_LEAD is 1 TXPICG_DQS_UI_OFFSET_LAG is 0 =========================================== set APHY_PI_CKCGH_CNT is 4 when not fake_mode, cur data_rate is 3200 [DIG_SHUF_CONFIG] MISC >>>>>, group_id=0 [DIG_SHUF_CONFIG] MISC <<<<<<, group_id=0 [DIG_SHUF_CONFIG] DBI >>>>>>, group_id=0 [DIG_SHUF_CONFIG] DBI <<<<<<, group_id=0 dramc_dram_ratio: 4 DDR4_DivMode: 1 freq_index: 1600 match AC timing 1 [DDR4_ac_timing_setting]start [PC4 WR preamble settings]>>>>>>>> group_id = 0. [PC4 WR preamble settings]<<<<<<<< group_id = 0. clk_dramc_ref_sel FREQ=16 fmem_ck_bfe_dcm_ch0 FREQ=253 fmem_ck_aft_dcm_ch0 FREQ=253 SetClkFreeRun enter => DRAM clock free run mode = ON. [DDR4] Pull Down reset. [DDR4] cke fix low 10ns at least. [DDR4] Delay 200 us. [DDR4] Pull Up reset. [DDR4] Delay 500 us. [DDR4] DRAM initilization RK:0 Enter >>>>>>>> [DDR4] Delay TXPR TRFC+10ns - 350ns(8Gb density)+10ns [DDR4_MRS] RK:0-MA:2-OP:0x[DDR4_MRS] RK:0-MA:3-OP:0x[DDR4_MRS] RK:0-MA:1-OP:0x[DDR4_MRS] RK:0-MA:4-OP:0x[DDR4_MRS] RK:0-MA:5-OP:0x[DDR4] DQ Vref calibration>>>>>>> [DDR4] DQ Vref Enable DQ vref calibration. [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] wait tVREFDQE-150ns [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] DQ Vref modify range and value [DDR4] DQ Vref Exit DQ vref calibration. [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] wait tVREFDQx-150ns [DDR4] DQ Vref calibration<<<<<<< [DDR4_MRS] RK:0-MA:0-OP:0x[DDR4_ZQ] RK:0 Enter >>>>>>>> [DDR4_ZQ] RK:0 Exit <<<<<<<< [DDR4] Delay ZQinit - 718ns for 1333 at least max(512Mck,640ns) [DDR4] DRAM initilization RK:0 Exit <<<<<<< [DDR4] Enable refresh.....All bank refresh only SetClkFreeRun enter => DRAM clock free run mode = OFF. [DIG_HW_NONSHUF_ZQCAL_SWITCH],Configuration Enter [DIG_HW_NONSHUF_DQSG_SWITCH],Configuration Enter SET_CKE_2_RANK_INDEPENDENT_RUN_TIME: ON [MiockJmeterHQA] =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [DramcMiockJmeter] u1RxGatingPI = 0 0 : 2282, 2282 1 : 2271, 2271 2 : 2271, 2271 3 : 2272, 2272 4 : 2271, 2271 5 : 2271, 2271 6 : 2276, 2276 7 : 2272, 2272 8 : 2272, 2272 9 : 2272, 2272 10 : 2272, 2272 11 : 2271, 2271 12 : 2271, 2271 13 : 2272, 2272 14 : 2271, 2271 15 : 2271, 2271 16 : 2272, 2272 17 : 2271, 2271 18 : 2271, 2271 19 : 2272, 2272 20 : 2271, 2271 21 : 2271, 2271 22 : 2271, 2271 23 : 2272, 2272 24 : 2271, 2271 25 : 2272, 2272 26 : 2271, 2271 27 : 2271, 2271 28 : 2272, 2272 29 : 2276, 2276 30 : 2272, 2272 31 : 2271, 2271 32 : 2272, 2272 33 : 2271, 2271 34 : 2272, 2272 35 : 2271, 2271 36 : 2271, 2271 37 : 2272, 1832 38 : 2271, 0 39 : 2272, 0 40 : 2271, 0 41 : 2272, 0 42 : 2267, 0 43 : 2267, 0 44 : 2271, 0 45 : 2272, 0 46 : 2271, 0 47 : 2271, 0 48 : 2267, 0 49 : 2271, 0 50 : 2271, 0 51 : 2272, 0 52 : 2271, 0 53 : 2271, 0 54 : 2271, 0 55 : 2271, 0 56 : 2272, 0 57 : 2271, 0 58 : 2271, 0 59 : 2276, 0 60 : 2276, 0 61 : 2271, 0 62 : 2272, 0 63 : 2276, 0 64 : 2271, 0 65 : 2272, 0 66 : 2276, 0 67 : 2272, 0 68 : 2272, 0 69 : 2271, 0 70 : 2271, 0 71 : 2272, 0 72 : 2276, 0 73 : 2271, 0 74 : 2271, 0 75 : 2272, 0 76 : 2271, 0 77 : 2271, 0 78 : 2271, 0 79 : 2272, 0 80 : 2271, 0 81 : 2271, 0 82 : 2276, 0 83 : 2271, 0 84 : 2272, 0 85 : 2272, 0 86 : 2271, 0 87 : 2266, 0 88 : 2272, 0 89 : 2271, 1888 90 : 2271, 2267 91 : 2271, 2271 92 : 2271, 2271 93 : 2272, 2272 94 : 2271, 2271 95 : 2272, 2272 96 : 2272, 2272 97 : 2276, 2276 98 : 2271, 2271 99 : 2271, 2271 100 : 2271, 2271 101 : 2271, 2271 102 : 2272, 2272 103 : 2272, 2272 104 : 2276, 2276 105 : 2272, 2272 106 : 2272, 2272 107 : 2276, 2276 108 : 2271, 2271 109 : 2271, 2271 110 : 2271, 2271 111 : 2272, 2272 112 : 2271, 2271 113 : 2271, 2271 114 : 2271, 2271 115 : 2271, 2271 116 : 2272, 2272 117 : 2271, 2271 118 : 2271, 2271 119 : 2271, 2271 120 : 2271, 2271 121 : 2271, 2271 122 : 2276, 2276 123 : 2271, 2271 124 : 2276, 2276 125 : 2271, 2271 126 : 2272, 2272 127 : 2271, 2271 MIOCK jitter meter ch=0 1T = (89-38)*2 = 102 dly cells Clock freq = 1560 MHz, period = 641 ps, 1 dly cell = 628/100 ps ----->DramcWriteLeveling(PI) begin... =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== Begin: 0, End: 63, Step: 1, Bound: 64 [DDR4_MRS] RK:0-MA:2-OP:0x[DDR4_MRS] RK:0-MA:1-OP:0x[Write Leveling] delay byte0 byte1 byte2 byte3 0 O1( 1 1 1 O1( 1 1 2 O1( 1 1 3 O1( 1 1 4 O1( 1 1 5 O1( 1 1 6 O1( 1 1 7 O1( 1 1 8 O1( 1 1 9 O1( 1 1 10 O1( 1 1 11 O1( 1 0 12 O1( 1 0 13 O1( 1 0 14 O1( 1 0 15 O1( 1 0 16 O1( 0 0 17 O1( 0 0 18 O1( 0 0 19 O1( 0 0 20 O1( 0 0 21 O1( 0 0 22 O1( 0 0 23 O1( 0 0 24 O1( 0 0 25 O1( 0 0 26 O1( 0 0 27 O1( 0 0 28 O1( 0 0 29 O1( 0 0 30 O1( 0 0 31 O1( 0 0 32 O1( 0 0 33 O1( 0 0 34 O1( 0 0 35 O1( 0 0 36 O1( 0 0 37 O1( 0 0 38 O1( 0 0 39 O1( 0 0 40 O1( 0 0 41 O1( 0 0 42 O1( 0 1 43 O1( 1 1 44 O1( 1 1 45 O1( 1 1 46 O1( 1 1 47 O1( 1 1 48 O1( 1 1 49 O1( 1 1 Early breakpass bytecount = 0xff (0xff: all bytes pass) [DDR4_MRS] RK:0-MA:1-OP:0x[DDR4_MRS] RK:0-MA:2-OP:0xWrite leveling (Byte 0): 43 => 43 Write leveling (Byte 1): 42 => 42 DramcWriteLeveling(PI) end<----- =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [Gating] SW mode calibration [get_gating_start_pos] calculated gating ui = 15 12 0 | B1->B0 | 1111 1212 | 1 1 | (0 0) (0 0) 12 4 | B1->B0 | 1111 1212 | 1 1 | (0 0) (0 0) 12 8 | B1->B0 | 1111 1212 | 1 1 | (0 0) (0 0) 12 12 | B1->B0 | 1111 1111 | 1 1 | (0 1) (0 1) 12 16 | B1->B0 | 1111 1111 | 1 1 | (0 1) (0 1) 12 20 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 12 24 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 12 28 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 13 0 | B1->B0 | 1111 1212 | 1 1 | (1 1) (1 1) 13 4 | B1->B0 | 1111 1212 | 1 1 | (1 1) (1 1) 13 8 | B1->B0 | 1111 1212 | 1 1 | (1 1) (1 1) 13 12 | B1->B0 | 2323 2222 | 0 0 | (0 0) (0 0) 13 16 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 13 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 13 24 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 13 28 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 14 0 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 14 4 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 14 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 14 12 | B1->B0 | 2323 2323 | 0 0 | (0 1) (0 0) 14 16 | B1->B0 | 2222 2323 | 0 0 | (1 1) (0 1) 14 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 14 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 14 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 0 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 4 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 8 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (0 0) 16 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 16 12 | B1->B0 | 2323 2323 | 0 0 | (0 1) (0 0) 16 16 | B1->B0 | 2323 2323 | 0 0 | (0 1) (0 1) 16 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 8 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 8 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 12 | B1->B0 | 2323 2323 | 0 0 | (1 0) (1 0) 18 16 | B1->B0 | 2323 2323 | 0 0 | (1 0) (1 0) 18 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 18 24 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 18 28 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 0 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 4 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) best dqsien dly found for B0: (18, 14) 19 12 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 16 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) best dqsien dly found for B1: (18, 14) best DQS0 dly(UI, PI) = (18, 14) best DQS1 dly(UI, PI) = (18, 14) [Gating] SW calibration Done [DDR4_MRS] RK:0-MA:3-OP:0x=============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== Start DQ dly to find pass range UseTestEngine =0 UseTestEngine: 0 RX Vref Scan: 0 RX Vref 0 -> 0, step: 1 RX Delay -48 -> 63, step: 4 -48, [0] xxxxxxxx xxxxxxxx [MSB] -44, [0] xxxxxxxx xxxxxxxx [MSB] -40, [0] xxxxxxxx xxxxxxxx [MSB] -36, [0] xxxxxxxx xxxxxxxx [MSB] -32, [0] xxxxxxxx xxxxxxxx [MSB] -28, [0] xxxxxxxx xxxxxxxx [MSB] -24, [0] xxxxxxxx xxxxxxxx [MSB] -20, [0] xxxxxxxx xxxxxxxx [MSB] -16, [0] xxxxxxxx xxxxxxxx [MSB] -12, [0] xxxxxxxx xxxxxxxx [MSB] -8, [0] xxxxxxxx xxxxxxxx [MSB] -4, [0] xxxxxxox xxxxxxxx [MSB] 0, [0] xxoxoxox xxoxoxxx [MSB] 4, [0] oxoooxoo oooooxoo [MSB] 8, [0] oooooooo oooooooo [MSB] 12, [0] oooooooo oooooooo [MSB] 16, [0] oooooooo oooooooo [MSB] 20, [0] oooooooo oooooooo [MSB] 24, [0] oooooooo oooooooo [MSB] 28, [0] oooooooo oooooooo [MSB] 32, [0] oooooooo oooooooo [MSB] 36, [0] ooxoooxo oooooooo [MSB] 40, [0] ooxoxoxo ooxoxoxo [MSB] 44, [0] xoxxxxxx xxxxxxxx [MSB] 48, [0] xxxxxxxx xxxxxxxx [MSB] RX Vref B0= 0, Window Sum 312, worse bit 2, min window 36 iDelay=48, Bit 0, Center 23 (4 ~ 43) 40 iDelay=48, Bit 1, Center 27 (8 ~ 47) 40 iDelay=48, Bit 2, Center 17 (0 ~ 35) 36 iDelay=48, Bit 3, Center 23 (4 ~ 43) 40 iDelay=48, Bit 4, Center 19 (0 ~ 39) 40 iDelay=48, Bit 5, Center 25 (8 ~ 43) 36 iDelay=48, Bit 6, Center 15 (-4 ~ 35) 40 iDelay=48, Bit 7, Center 23 (4 ~ 43) 40 RX Vref B1= 0, Window Sum 312, worse bit 13, min window 36 iDelay=48, Bit 8, Center 23 (4 ~ 43) 40 iDelay=48, Bit 9, Center 23 (4 ~ 43) 40 iDelay=48, Bit 10, Center 19 (0 ~ 39) 40 iDelay=48, Bit 11, Center 23 (4 ~ 43) 40 iDelay=48, Bit 12, Center 19 (0 ~ 39) 40 iDelay=48, Bit 13, Center 25 (8 ~ 43) 36 iDelay=48, Bit 14, Center 21 (4 ~ 39) 36 iDelay=48, Bit 15, Center 23 (4 ~ 43) 40 [DDR4_MRS] RK:0-MA:3-OP:0x=============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== DQS Delay: DQS0 = 0, DQS1 = 0 DQM Delay: DQM0 = 21, DQM1 = 22 DQ Delay: DQ0 =23, DQ1 =27, DQ2 =17, DQ3 =23 DQ4 =19, DQ5 =25, DQ6 =15, DQ7 =23 DQ8 =23, DQ9 =23, DQ10 =19, DQ11 =23 DQ12 =19, DQ13 =25, DQ14 =21, DQ15 =23 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [TxWindowPerbitCal] caltype:2 Autok:0 TX Vref Scan disable 810 |3 0 42|[0] xxxxxxox xxxxxxxx [MSB] 812 |3 0 44|[0] oxoxxxox xxxxxxxx [MSB] 814 |3 0 46|[0] oxoxxxox xxxxxxxx [MSB] 816 |3 0 48|[0] oxoxxxox xxoxxxox [MSB] 818 |3 0 50|[0] oooooooo oxoooooo [MSB] 832 |3 2 0|[0] ooooooxo ooxooooo [MSB] 834 |3 2 2|[0] xoxoxoxo xoxoxooo [MSB] 836 |3 2 4|[0] xoxoxoxo xxxxxoxx [MSB] 838 |3 2 6|[0] xoxxxxxo xxxxxxxx [MSB] 840 |3 2 8|[0] xxxxxxxx xxxxxxxx [MSB] TX Bit0 (812~832) 22 822, Bit8 (818~832) 16 825, TX Bit1 (818~838) 22 828, Bit9 (820~834) 16 827, TX Bit2 (812~832) 22 822, Bit10 (816~830) 16 823, TX Bit3 (818~836) 20 827, Bit11 (818~834) 18 826, TX Bit4 (818~832) 16 825, Bit12 (818~832) 16 825, TX Bit5 (818~836) 20 827, Bit13 (818~836) 20 827, TX Bit6 (810~830) 22 820, Bit14 (816~834) 20 825, TX Bit7 (818~838) 22 828, Bit15 (818~834) 18 826, == TX Byte 0 == Update DQ dly =824 (3 ,0, 56) DQ OEN =(2 ,5) Update DQM dly =824 (3 ,0, 56) DQM OEN =(2 ,5) == TX Byte 1 == Update DQ dly =825 (3 ,0, 57) DQ OEN =(2 ,5) Update DQM dly =825 (3 ,0, 57) DQM OEN =(2 ,5) =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [TxWindowPerbitCal] caltype:0 Autok:0 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 3 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 5 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 7 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 9 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 11 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 13 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 15 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 17 TX Vref=3, minBit 8, minWin=13, winSum=263 TX Vref=5, minBit 9, minWin=14, winSum=275 TX Vref=7, minBit 10, minWin=14, winSum=281 TX Vref=9, minBit 9, minWin=16, winSum=295 TX Vref=11, minBit 10, minWin=15, winSum=299 TX Vref=13, minBit 10, minWin=15, winSum=305 TX Vref=15, minBit 9, minWin=17, winSum=317 TX Vref=17, minBit 4, minWin=18, winSum=323 [TxChooseVref] Worse bit 4, Min win 18, Win sum 323, Final Vref 17 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 17 Final TX Range 1 Vref 17 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [TxWindowPerbitCal] caltype:0 Autok:0 TX Vref Scan disable 810 |3 0 42|[0] xxxxxxxx xxxxxxxx [MSB] 811 |3 0 43|[0] xxxxxxox xxxxxxxx [MSB] 812 |3 0 44|[0] xxxxxxox xxxxxxxx [MSB] 813 |3 0 45|[0] xxxxxxox xxxxxxxx [MSB] 814 |3 0 46|[0] oxoxxxox xxoxxxxx [MSB] 815 |3 0 47|[0] oxoxxxox xxoxoxox [MSB] 816 |3 0 48|[0] oxoxxxox xxoxoooo [MSB] 817 |3 0 49|[0] oooooooo oxoooooo [MSB] 833 |3 2 1|[0] ooooooxo oooooooo [MSB] 834 |3 2 2|[0] xoxoooxo ooxooooo [MSB] 835 |3 2 3|[0] xoxoxoxo xoxoxooo [MSB] 836 |3 2 4|[0] xoxoxoxo xoxxxoxx [MSB] 837 |3 2 5|[0] xoxoxoxo xxxxxxxx [MSB] 838 |3 2 6|[0] xoxxxoxo xxxxxxxx [MSB] 839 |3 2 7|[0] xoxxxxxo xxxxxxxx [MSB] 840 |3 2 8|[0] xxxxxxxx xxxxxxxx [MSB] TX Bit0 (814~833) 20 823, Bit8 (817~834) 18 825, TX Bit1 (817~839) 23 828, Bit9 (818~836) 19 827, TX Bit2 (814~833) 20 823, Bit10 (814~833) 20 823, TX Bit3 (817~837) 21 827, Bit11 (817~835) 19 826, TX Bit4 (817~834) 18 825, Bit12 (815~834) 20 824, TX Bit5 (817~838) 22 827, Bit13 (816~836) 21 826, TX Bit6 (811~832) 22 821, Bit14 (815~835) 21 825, TX Bit7 (817~839) 23 828, Bit15 (816~835) 20 825, [TX_PER_BIT_DELAY_CELL] DelayCellTimex100 =628/100 ps == TX Byte 0 == u2DelayCellOfst[0]=3 cells (2 PI) u2DelayCellOfst[1]=10 cells (7 PI) u2DelayCellOfst[2]=3 cells (2 PI) u2DelayCellOfst[3]=9 cells (6 PI) u2DelayCellOfst[4]=6 cells (4 PI) u2DelayCellOfst[5]=9 cells (6 PI) u2DelayCellOfst[6]=0 cells (0 PI) u2DelayCellOfst[7]=10 cells (7 PI) Update DQ dly =821 (3 ,0, 53) DQ OEN =(2 ,5) Update DQM dly =824 (3 ,0, 56) DQM OEN =(2 ,5) == TX Byte 1 == u2DelayCellOfst[8]=3 cells (2 PI) u2DelayCellOfst[9]=6 cells (4 PI) u2DelayCellOfst[10]=0 cells (0 PI) u2DelayCellOfst[11]=4 cells (3 PI) u2DelayCellOfst[12]=1 cells (1 PI) u2DelayCellOfst[13]=4 cells (3 PI) u2DelayCellOfst[14]=3 cells (2 PI) u2DelayCellOfst[15]=3 cells (2 PI) Update DQ dly =823 (3 ,0, 55) DQ OEN =(2 ,5) Update DQM dly =825 (3 ,0, 57) DQM OEN =(2 ,5) =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== DATLAT Default: 0xc 0, 0x1, 0x2, 0x3, 0x4, 0x5, 0x6, 0x7, 0x8, 0x9, 0x10, 0x11, 0x12, 0x13, 0xbest_step = 11 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== Start DQ dly to find pass range UseTestEngine =1 UseTestEngine: 1 RX Vref Scan: 1 Set Vref Range= 9 -> 21 RX Vref 9 -> 21, step: 1 RX Delay -14 -> 63, step: 2 Set Vref, RX VrefLevel [Byte0]: 9 [Byte1]: 9 RX Vref B0= 9, Window Sum 226, worse bit 6, min window 26 RX Vref B1= 9, Window Sum 208, worse bit 10, min window 24 Set Vref, RX VrefLevel [Byte0]: 10 [Byte1]: 10 RX Vref B0= 10, Window Sum 236, worse bit 4, min window 28 RX Vref B1= 10, Window Sum 222, worse bit 10, min window 26 Set Vref, RX VrefLevel [Byte0]: 11 [Byte1]: 11 RX Vref B0= 11, Window Sum 250, worse bit 0, min window 30 RX Vref B1= 11, Window Sum 236, worse bit 10, min window 26 Set Vref, RX VrefLevel [Byte0]: 12 [Byte1]: 12 RX Vref B0= 12, Window Sum 260, worse bit 0, min window 32 RX Vref B1= 12, Window Sum 240, worse bit 10, min window 28 Set Vref, RX VrefLevel [Byte0]: 13 [Byte1]: 13 RX Vref B0= 13, Window Sum 264, worse bit 0, min window 32 RX Vref B1= 13, Window Sum 246, worse bit 10, min window 28 Set Vref, RX VrefLevel [Byte0]: 14 [Byte1]: 14 RX Vref B0= 14, Window Sum 278, worse bit 1, min window 34 RX Vref B1= 14, Window Sum 260, worse bit 10, min window 30 Set Vref, RX VrefLevel [Byte0]: 15 [Byte1]: 15 RX Vref B0= 15, Window Sum 286, worse bit 4, min window 34 RX Vref B1= 15, Window Sum 266, worse bit 9, min window 32 Set Vref, RX VrefLevel [Byte0]: 16 [Byte1]: 16 RX Vref B1= 16, Window Sum 276, worse bit 10, min window 32 Set Vref, RX VrefLevel [Byte0]: 17 [Byte1]: 17 RX Vref B0= 17, Window Sum 294, worse bit 0, min window 36 RX Vref B1= 17, Window Sum 280, worse bit 8, min window 34 Set Vref, RX VrefLevel [Byte0]: 18 [Byte1]: 18 RX Vref B1= 18, Window Sum 290, worse bit 8, min window 34 Set Vref, RX VrefLevel [Byte0]: 19 [Byte1]: 19 Set Vref, RX VrefLevel [Byte0]: 20 [Byte1]: 20 Final RX Vref Byte 0 = 17 to rank0 to rank1 Final RX Vref Byte 1 = 18 to rank0 to rank1 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== DQS Delay: DQS0 = 0, DQS1 = 0 DQM Delay: DQM0 = 22, DQM1 = 24 DQ Delay: DQ0 =23, DQ1 =27, DQ2 =19, DQ3 =25 DQ4 =21, DQ5 =26, DQ6 =16, DQ7 =24 DQ8 =24, DQ9 =26, DQ10 =22, DQ11 =26 DQ12 =22, DQ13 =26, DQ14 =22, DQ15 =25 [DualRankRxdatlatCal] RK0: 11, RK1: 0, Final_Datlat 11 [Calibration Summary] Freqency 1600 CH 0, Rank 0 SW Impedance : PASS DUTY Scan : NO K ZQ Calibration : PASS Jitter Meter : NO K CBT Training : NO K Write leveling : PASS RX DQS gating : PASS RX DQ/DQS(RDDQC) : PASS TX DQ/DQS : PASS RX DATLAT : PASS RX DQ/DQS(Engine): PASS TX OE : NO K All Pass. TX_TRACKING: OFF [AUTO] write start address pass, BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] Detect DramSize: 0x8000000 [AUTO] BASE_ADDR : 0x8000000, OFFSET : 0x3 [AUTO] BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] Detect DramSize: 0x10000000 [AUTO] BASE_ADDR : 0x10000000, OFFSET : 0x3 [AUTO] BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] Detect DramSize: 0x20000000 [AUTO] BASE_ADDR : 0x20000000, OFFSET : 0x3 [AUTO] BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] TA2 read check fail, u4err_value = 65535, 3 [AUTO] Detect full size u4DramSize 0x20000000 NOTICE: EMI: Detected DRAM size: 512MB [MEM_TEST] 02: After DFS, before run time config [MEM_TEST] Rank 0 OK.(uiFixedAddr 0x40000000, Pass count = 16384, Fail count = 0) [TA2_TEST] === TA2 HW === OFFSET:0x200 TA2 PAT: 3 TA2 Trigger Write HW channel(0) Rank(0), TA2 pass, pass_cnt:1, err_cnt:0 [DramcRunTimeConfig]: ON PHYPLL DPM_CONTROL_AFTERK: ON PER_BANK_REFRESH: OFF REFRESH_OVERHEAD_REDUCTION: ON CMD_PICG_NEW_MODE: OFF TX_TRACKING: OFF RDSEL_TRACKING: OFF DQS Precalculation for DVFS: OFF RX_TRACKING: OFF DDR_HW_GATING DBG: ON DDR_ZQCS_ENABLE: ON RX_PICG_NEW_MODE: ON TX_PICG_NEW_MODE: ON ENABLE_RX_DCM_DPHY: ON LOWPOWER_GOLDEN_SETTINGS(DCM): ON DUMMY_READ_FOR_TRACKING: OFF !!! SPM_CONTROL_AFTERK: OFF !!! SPM could not control APHY IMPEDANCE_TRACKING: OFF HW_SAVE_FOR_SR: OFF CLK_FREE_FUN_FOR_DRAMC_PSEL: OFF PA_IMPROVEMENT_FOR_DRAMC_ACTIVE_POWER: OFF Read ODT Tracking: OFF Refresh Rate DeBounce: OFF DFS_NO_QUEUE_FLUSH: OFF DFS_NO_QUEUE_FLUSH_LATENCY_CNT: OFF ENABLE_DFS_RUNTIME_MRW: OFF DDR_RESERVE_NEW_MODE: ON ========================= [MEM_TEST] 03: After run time config [MEM_TEST] Rank 0 OK.(uiFixedAddr 0x40000000, Pass count = 16384, Fail count = 0) [TA2_TEST] === TA2 HW === OFFSET:0x200 TA2 Trigger Write HW channel(0) Rank(0), TA2 pass, pass_cnt:2, err_cnt:0 Init_DRAM:2480: init PCDDR4 dram End EMI: complex real chip dram calibration Verify pattern 1 (0x00~0xff)... EMI: mem8_base[0] = pattern8 = 0x0 Verify pattern 2 (0x00~0xffff)... EMI: mem16_base[0] = pattern16 = 0x0 Verify pattern 3 (0x00~0xffffffff)... EMI: mem32_base[0] = pattern32 = 0x0 NOTICE: EMI: complex R/W mem test passed drm_dram_reserved: MTK_DRM_MODE(22000000) NOTICE: SPI_NAND parses attributes from parameter page. NOTICE: SPI_NAND Detected ID 0x0 NOTICE: Page size 2048, Block size 131072, size 134217728 NOTICE: Initializing NMBM ... NOTICE: Signature found at block 1023 [0x07fe0000] NOTICE: First info table with writecount 0 found in block 960 NOTICE: Second info table with writecount 0 found in block 963 NOTICE: NMBM has been successfully attached in read-only mode INFO: BL2: Loading image id 3 INFO: Loading image id=3 at address 0x42000000 INFO: Image id=3 loaded: 0x42000000 - 0x42009061 INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0x42000000 INFO: Image id=5 loaded: 0x42000000 - 0x420ae288 NOTICE: BL2: Booting BL31 INFO: Entry point address = 0x43001000 INFO: SPSR = 0x3cd INFO: Total CPU count: 4 INFO: MCUSYS: Disable 512KB L2C shared SRAM INFO: check_ver = 0 INFO: Secondary bootloader is AArch64 INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: Maximum SPI INTID supported: 671 INFO: SPMC: Changed to SPMC mode NOTICE: BL31: v2.6(release):2598dbc2a6-dirty NOTICE: BL31: Built : 13:34:54, Mar 12 2022 INFO: [MPU](Region0)sa:0x0300, ea:0x0302 INFO: [MPU](Region0)apc0:0x80b6db69, apc1:0x00b6db6d INFO: [MPU](Region1)sa:0x0000, ea:0x0000 INFO: [MPU](Region1)apc0:0x00000000, apc1:0x00000000 INFO: [MPU](Region2)sa:0x0000, ea:0x0000 INFO: [MPU](Region2)apc0:0x00000000, apc1:0x00000000 INFO: [MPU](Region3)sa:0x0000, ea:0x0000 INFO: [MPU](Region3)apc0:0x00000000, apc1:0x00000000 INFO: [DEVAPC] devapc_init done INFO: BL31: Initializing runtime services INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x41e00000 INFO: SPSR = 0x3c9 In: serial@11002000 Out: serial@11002000 Err: serial@11002000 Net: eth0: ethernet@15100000 detect button reset released! Reading from 0x0 to 0x5f7fdd8c, size 0x4 ... OK Reading from 0x0 to 0x5f7fdd8c, size 0x4 ... OK Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK Writing to MTD device 'nmbm0'... OK OK Booting System 1 ubi0: attaching mtd10 ubi0: scanning is finished ubi0: attached mtd10 (name "ubi1", size 30 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 662404348 ubi0: available PEBs: 64, total reserved PEBs: 176, PEBs reserved for bad PEB handling: 19 Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK ## Loading kernel from FIT Image at 46000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-5.4.150 Type: Kernel Image Compression: lzma compressed Data Start: 0x460000e8 Data Size: 3160816 Bytes = 3 MiB Architecture: AArch64 OS: Linux Load Address: 0x44080000 Entry Point: 0x44080000 Hash algo: crc32 Hash value: bd0e32dd Hash algo: sha1 Hash value: 994c9b27486ab63b8f302c3fb83dd30b09d54027 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 46000000 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM64 OpenWrt mt7986-RB06 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x46303d14 Data Size: 20485 Bytes = 20 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 4c66671d Hash algo: sha1 Hash value: 65a8b044ad027aa577386dd21f4a51ac0a9e6287 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x46303d14 Uncompressing Kernel Image Loading Device Tree to 000000005f7f1000, end 000000005f7f9004 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.4.150 (jenkins@a92f094d1440) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 unknown)) #0 SMP Fri Aug 12 08:32:47 2022 [ 0.000000] Machine model: MediaTek MT7986a RFB [ 0.000000] On node 0 totalpages: 130064 [ 0.000000] DMA32 zone: 2048 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 130064 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s43608 r8192 d30120 u81920 [ 0.000000] pcpu-alloc: s43608 r8192 d30120 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 128016 [ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 491052K/520256K available (6398K kernel code, 490K rwdata, 1892K rodata, 448K init, 283K bss, 29204K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2d4/0x418 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000002] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000102] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000) [ 0.000108] pid_max: default: 32768 minimum: 301 [ 0.000158] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.000163] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.000810] ASID allocator initialised with 65536 entries [ 0.000845] rcu: Hierarchical SRCU implementation. [ 0.001053] smp: Bringing up secondary CPUs ... [ 0.001263] Detected VIPT I-cache on CPU1 [ 0.001282] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.001301] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.001520] Detected VIPT I-cache on CPU2 [ 0.001528] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000 [ 0.001537] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.001727] Detected VIPT I-cache on CPU3 [ 0.001735] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000 [ 0.001742] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.001768] smp: Brought up 1 node, 4 CPUs [ 0.001778] SMP: Total of 4 processors activated. [ 0.001781] CPU features: detected: 32-bit EL0 Support [ 0.001784] CPU features: detected: CRC32 instructions [ 0.001871] CPU: All CPU(s) started at EL2 [ 0.001881] alternatives: patching kernel code [ 0.003577] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.003593] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.003706] pinctrl core: initialized pinctrl subsystem [ 0.004178] NET: Registered protocol family 16 [ 0.004344] DMA: preallocated 256 KiB pool for atomic allocations [ 0.005193] pstore: Registered ramoops as persistent store backend [ 0.005200] ramoops: using 0x100000@0x42f00000, ecc: 0 [ 0.012358] cryptd: max_cpu_qlen set to 1000 [ 0.013391] SCSI subsystem initialized [ 0.013485] libata version 3.00 loaded. [ 0.013963] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.014443] rbus 18000000.wbsys: PCI host bridge to bus 0000:00 [ 0.014451] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff] [ 0.014457] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.014461] pci_bus 0000:00: scanning bus [ 0.014476] pci 0000:00:00.0: [14c3:7986] type 00 class 0x000280 [ 0.014488] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit] [ 0.014493] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f] [ 0.014497] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f] [ 0.014501] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f] [ 0.014505] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f] [ 0.015152] pci_bus 0000:00: fixups for bus [ 0.015156] pci_bus 0000:00: bus scan returning with max=00 [ 0.015371] clocksource: Switched to clocksource arch_sys_counter [ 0.015780] thermal_sys: Registered thermal governor 'fair_share' [ 0.015782] thermal_sys: Registered thermal governor 'bang_bang' [ 0.015786] thermal_sys: Registered thermal governor 'step_wise' [ 0.015789] thermal_sys: Registered thermal governor 'user_space' [ 0.015792] thermal_sys: Registered thermal governor 'power_allocator' [ 0.015972] NET: Registered protocol family 2 [ 0.016034] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.016359] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.016366] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.016386] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.016426] TCP: Hash tables configured (established 4096 bind 4096) [ 0.016477] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.016487] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.016562] NET: Registered protocol family 1 [ 0.016586] PCI: CLS 0 bytes, default 64 [ 0.017261] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 0.019005] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.019015] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.027817] mtk-pcie 11280000.pcie: host bridge /pcie@11280000 ranges: [ 0.027828] mtk-pcie 11280000.pcie: Parsing ranges property... [ 0.027834] mtk-pcie 11280000.pcie: MEM 0x20000000..0x2fffffff -> 0x20000000 [ 0.235392] mtk-pcie 11280000.pcie: PCIe link down, ltssm reg val: 0x1000001 [ 0.235447] mtk-pcie: probe of 11280000.pcie failed with error -110 [ 0.242974] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.243451] printk: console [ttyS0] disabled [ 0.263571] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 12, base_baud = 2500000) is a ST16650V2 [ 0.944134] printk: console [ttyS0] enabled [ 0.968665] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 13, base_baud = 1625000) is a ST16650V2 [ 0.998101] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 14, base_baud = 1625000) is a ST16650V2 [ 1.007647] mtk_rng 1020f000.trng: registered RNG driver [ 1.007873] random: fast init done [ 1.013063] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.016580] random: crng init done [ 1.023962] loop: module loaded [ 1.030157] spi-nor spi0.0: unrecognized JEDEC id bytes: ff c8 01 7f 7f 7f [ 1.037039] spi-nor: probe of spi0.0 failed with error -2 [ 1.042565] spi-nand spi0.1: GigaDevice/ESMT SPI NAND was found. [ 1.048565] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 1.057637] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 1.065004] libphy: Fixed MDIO Bus: probed [ 1.069475] tun: Universal TUN/TAP device driver, 1.6 [ 1.074678] mtk_probe none-cache-api init ! [ 1.079030] mtk_hw_init 3055 pending:0 [ 1.082851] mtk_hw_init 3060 pn-clk init [ 1.086868] mtk_hw_init 3069 [ 1.089822] mtk_hw_init 3086 [ 1.092778] mtk_eth_cold_reset 2975 [ 1.107340] ethsys_reset 2852 i:0 set:c0800040 read:6000004 reset:1 [ 1.113590] ############ mtk_eth_fe_reset_update 1555 val:c0800040 fe_reset.val_s:c0800040 [ 1.121918] ############ mtk_eth_fe_reset_update 1559 val:6000004 fe_reset.val_r:6000004 [ 1.130072] ############ mtk_eth_fe_reset_update 1572 val:0 fe_reset.cold_cnt:1 [ 1.137446] mtk_hw_init 3094 read 0 rstctl:0 [ 1.137447] mtk_hw_init 3095 [ 1.144654] mtk_hw_init 3103 FE/PPE/GMAC reset done [ 1.149702] mtk_probe 4263 fe-irq:127 [ 1.153490] libphy: mdio: probed [ 1.201582] mtk_soc_eth 15100000.ethernet: generated random MAC address de:20:67:c6:42:fa [ 1.209961] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc011a00000, irq 124 [ 1.219092] mtk_soc_eth 15100000.ethernet: generated random MAC address 2e:b3:00:75:bc:93 [ 1.227407] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc011a00000, irq 124 [ 1.236519] (unnamed net_device) (dummy): netif_napi_add() called with weight 256 [ 1.244022] 500210440 -> init fe_reset [ 1.247846] [mtk_probe] mtk_dma_monitor_timer is initialized ! [ 1.253830] i2c /dev entries driver [ 1.258285] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.266163] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 1.274875] leds-hm0807a spi1.0: led_driver_probe [ 1.279571] leds-hm0807a spi1.0: chip_num:5, led_num:5. [ 1.284782] leds-hm0807a spi1.0: led_driver_probe name:led_red [ 1.290628] leds-hm0807a spi1.0: led_driver_probe name:led_blue [ 1.296809] leds-hm0807a spi1.0: led_driver_probe name:led_yellow [ 1.302912] leds-hm0807a spi1.0: led_driver_probe name:led_white [ 1.308927] leds-hm0807a spi1.0: led_driver_probe name:led_green [ 1.315120] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433,alg:7fcdfc00 [ 1.328094] Initializing XFRM netlink socket [ 1.332571] NET: Registered protocol family 10 [ 1.337472] Segment Routing with IPv6 [ 1.341167] NET: Registered protocol family 17 [ 1.345606] NET: Registered protocol family 15 [ 1.350059] Bridge firewalling registered [ 1.354055] 8021q: 802.1Q VLAN Support v1.8 [ 1.358728] pstore: Using crash dump compression: deflate [ 1.370324] nmbm nmbm_spim_nand: Signature found at block 1023 [0x07fe0000] [ 1.378152] nmbm nmbm_spim_nand: First info table with writecount 0 found in block 960 [ 1.388640] nmbm nmbm_spim_nand: Second info table with writecount 0 found in block 963 [ 1.396641] nmbm nmbm_spim_nand: NMBM has been successfully attached [ 1.403193] 10 fixed-partitions partitions found on MTD device nmbm_spim_nand [ 1.410312] Creating 10 MTD partitions on "nmbm_spim_nand": [ 1.415869] 0x000000000000-0x000000100000 : "BL2" [ 1.420965] 0x000000100000-0x000000140000 : "Nvram" [ 1.426115] 0x000000140000-0x000000180000 : "Bdata" [ 1.431252] 0x000000180000-0x000000380000 : "Factory" [ 1.436565] 0x000000380000-0x000000580000 : "FIP" [ 1.441531] 0x000000580000-0x0000005c0000 : "crash" [ 1.446672] 0x0000005c0000-0x000000600000 : "crash_log" [ 1.452178] 0x000000600000-0x000002400000 : "ubi" [ 1.457185] 0x000002400000-0x000004200000 : "ubi1" [ 1.462282] 0x000004200000-0x000007400000 : "overlay" [ 2.019402] mt753x gsw@0: LAN/WAN VLAN setting=llllw [ 2.024626] mt753x gsw@0: Switch is MediaTek MT7531AE rev 1 [ 2.034039] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz [ 4.063757] libphy: mt753x_mdio: probed [ 4.067625] init port map proc seccess! [ 5.681177] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: [ 5.692959] mt753x gsw@0: -------- gephy-calbration (port:0) -------- [ 5.708146] CALDLY = 40 [ 5.775868] 0x1e-e0 = 2a2a [ 5.780260] 0x1f-115 = 5 [ 5.782777] GE Rext AnaCal Done! (10)(0x2a) [ 5.860533] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 5.933696] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 6.006860] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 6.084577] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.092417] GE 1e_174(0xa6a6), 1e_175(0xa6a4) [ 6.129651] GE Tx offset AnaCal Done! (pair-0)(2)(0x21) 0x1e_172=0x2120 [ 6.163595] GE Tx offset AnaCal Done! (pair-1)(4)(0x23) 0x1e_172=0x2123 [ 6.188437] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120 [ 6.213280] GE Tx offset AnaCal Done! (pair-3)(2)(0x2) 0x1e_173=0x2102 [ 6.310410] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x741d) [ 6.416231] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2525) [ 6.463262] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1a22) [ 6.532923] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1f27) [ 6.579586] PORT 0 RX_DC_OFFSET [ 6.592237] before pairA output = 1d [ 6.597580] after pairA output = fe [ 6.602755] before pairB output = 1e [ 6.608097] after pairB output = 1 [ 6.613186] before pairC output = d [ 6.618441] after pairC output = 0 [ 6.623532] before pairD output = 1e [ 6.628870] after pairD output = ff [ 6.632601] mt753x gsw@0: -------- gephy-calbration (port:1) -------- [ 6.647788] CALDLY = 40 [ 6.728046] GE R50 AnaCal Done! (15) (0x23)(0xa3) [ 6.810313] GE R50 AnaCal Done! (15) (0x23)(0xa3) [ 6.878928] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 6.947545] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 6.955385] GE 1e_174(0xa3a3), 1e_175(0xb0b0) [ 7.006269] GE Tx offset AnaCal Done! (pair-0)(5)(0x5) 0x1e_172=0x520 [ 7.030939] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x521 [ 7.055694] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120 [ 7.085088] GE Tx offset AnaCal Done! (pair-3)(3)(0x22) 0x1e_173=0x2122 [ 7.154017] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5415) [ 7.214576] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1e1e) [ 7.267264] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1c24) [ 7.331267] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1e26) [ 7.377929] PORT 1 RX_DC_OFFSET [ 7.390582] before pairA output = e [ 7.395837] after pairA output = 1 [ 7.400924] before pairB output = f [ 7.406179] after pairB output = ff [ 7.411354] before pairC output = 1e [ 7.416696] after pairC output = 0 [ 7.421785] before pairD output = f [ 7.427040] after pairD output = 1 [ 7.430684] mt753x gsw@0: -------- gephy-calbration (port:2) -------- [ 7.445870] CALDLY = 40 [ 7.507931] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 7.576543] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 7.645157] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 7.713771] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 7.721611] GE 1e_174(0xb1b0), 1e_175(0xb0b0) [ 7.772498] GE Tx offset AnaCal Done! (pair-0)(5)(0x24) 0x1e_172=0x2420 [ 7.797343] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2421 [ 7.822185] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120 [ 7.856129] GE Tx offset AnaCal Done! (pair-3)(4)(0x23) 0x1e_173=0x2123 [ 7.925059] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5816) [ 7.979961] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1c1c) [ 8.026994] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1c24) [ 8.074025] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x131b) [ 8.120687] PORT 2 RX_DC_OFFSET [ 8.133342] before pairA output = 1e [ 8.138684] after pairA output = 0 [ 8.143772] before pairB output = 1e [ 8.149111] after pairB output = 0 [ 8.154200] before pairC output = d [ 8.159455] after pairC output = ff [ 8.164627] before pairD output = e [ 8.169883] after pairD output = 0 [ 8.173526] mt753x gsw@0: -------- gephy-calbration (port:3) -------- [ 8.188713] CALDLY = 40 [ 8.259874] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 8.328489] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 8.401656] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 8.465720] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 8.473561] GE 1e_174(0xa6b0), 1e_175(0xa6b1) [ 8.519896] GE Tx offset AnaCal Done! (pair-0)(4)(0x23) 0x1e_172=0x2320 [ 8.544738] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2321 [ 8.569581] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120 [ 8.594425] GE Tx offset AnaCal Done! (pair-3)(2)(0x21) 0x1e_173=0x2121 [ 8.669013] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6c1b) [ 8.740886] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2020) [ 8.810547] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2028) [ 8.840611] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x171f) [ 8.887273] PORT 3 RX_DC_OFFSET [ 8.899926] before pairA output = f [ 8.905181] after pairA output = ff [ 8.910356] before pairB output = f [ 8.915611] after pairB output = ff [ 8.920783] before pairC output = 1e [ 8.926125] after pairC output = 0 [ 8.931214] before pairD output = 1e [ 8.936557] after pairD output = ff [ 8.940288] mt753x gsw@0: -------- gephy-calbration (port:4) -------- [ 8.955476] CALDLY = 40 [ 9.012982] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 9.072498] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 9.127459] GE R50 AnaCal Done! (9) (0x34)(0xb4) [ 9.186887] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 9.194729] GE 1e_174(0xb2b2), 1e_175(0xb4b2) [ 9.227414] GE Tx offset AnaCal Done! (pair-0)(1)(0x1) 0x1e_172=0x120 [ 9.265736] GE Tx offset AnaCal Done! (pair-1)(5)(0x24) 0x1e_172=0x124 [ 9.295045] GE Tx offset AnaCal Done! (pair-2)(3)(0x22) 0x1e_173=0x2220 [ 9.319887] GE Tx offset AnaCal Done! (pair-3)(2)(0x21) 0x1e_173=0x2221 [ 9.383160] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5c17) [ 9.438063] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1212) [ 9.490753] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x131b) [ 9.526470] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x161e) [ 9.573133] PORT 4 RX_DC_OFFSET [ 9.585786] before pairA output = 1d [ 9.591129] after pairA output = ff [ 9.596304] before pairB output = e [ 9.601560] after pairB output = ff [ 9.606735] before pairC output = 1d [ 9.612078] after pairC output = 0 [ 9.617167] before pairD output = f [ 9.622422] after pairD output = 0 [ 9.628243] UBI: auto-attach mtd9 [ 9.631555] ubi0: attaching mtd9 [ 9.727410] ubi0: scanning is finished [ 9.735705] ubi0: attached mtd9 (name "ubi1", size 30 MiB) [ 9.741177] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 9.748032] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 9.754799] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 9.761740] ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0 [ 9.767727] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 9.774928] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 662404348 [ 9.783948] ubi0: available PEBs: 64, total reserved PEBs: 176, PEBs reserved for bad PEB handling: 19 [ 9.793233] ubi0: background thread "ubi_bgt0d" started, PID 831 [ 9.793774] block ubiblock0_1: created from ubi0:1(rootfs) [ 9.804692] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 9.811637] hctosys: unable to open rtc device (rtc0) [ 9.829487] Failed to lock mtd obr [ 9.831810] VFS: Mounted root (squashfs filesystem) readonly on device 253:0. [ 9.842532] Freeing unused kernel memory: 448K [ 9.859397] Run /sbin/init as init process [ 10.034777] init: Console is alive [ 10.038275] init: - watchdog - [ 10.296260] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 10.318339] conninfra@(mtk_conninfra_drv_init:644) Before platform_driver_register [ 10.326025] Get Index(0-TOP_MISC_BASE) phy_addr(0x11d10000) vir_addr=(0xffffffc010a6d000) size=(0x1000) [ 10.335401] Get Index(1-TOPRGU_BASE) phy_addr(0x1001c000) vir_addr=(0xffffffc010a75000) size=(0x1000) [ 10.344598] Get Index(2-GPIO_BASE) phy_addr(0x1001f000) vir_addr=(0xffffffc010a7d000) size=(0x1000) [ 10.353621] Get Index(3-IOCFG_TR_BASE) phy_addr(0x11f00000) vir_addr=(0xffffffc010a85000) size=(0x1000) [ 10.362990] Get Index(4-IOCFG_TL_BASE) phy_addr(0x11f10000) vir_addr=(0xffffffc010a8d000) size=(0x1000) [ 10.372360] Get Index(5-INFRACFG_AO_BASE) phy_addr(0x10003000) vir_addr=(0xffffffc010a95000) size=(0x1000) [ 10.381989] Get Index(6-CONN_INFRA_CFG_BASE) phy_addr(0x18001000) vir_addr=(0xffffffc010a9d000) size=(0x1000) [ 10.391879] Get Index(7-CONN_INFRA_SYSRAM_BASE) phy_addr(0x18050000) vir_addr=(0xffffffc010aa5000) size=(0x1000) [ 10.402028] Get Index(8-CONN_INFRA_CLKGEN_ON_TOP_BASE) phy_addr(0x18009000) vir_addr=(0xffffffc010aad000) size=(0x1000) [ 10.412784] Get Index(9-CONN_HOST_CSR_TOP_BASE) phy_addr(0x18060000) vir_addr=(0xffffffc010ab5000) size=(0x1000) [ 10.422934] Get Index(10-CONN_INFRA_BUS_CR_BASE) phy_addr(0x1800e000) vir_addr=(0xffffffc010abd000) size=(0x1000) [ 10.433171] Get Index(11-CONN_INFRA_RGU_BASE) phy_addr(0x18000000) vir_addr=(0xffffffc010ac5000) size=(0x1000) [ 10.443149] Get Index(12-CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18005000) vir_addr=(0xffffffc010acd000) size=(0x1000) [ 10.453559] Get Index(13-INST2_CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18085000) vir_addr=(0xffffffc010acf000) size=(0x1000) [ 10.464487] Get Index(14-CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18004000) vir_addr=(0xffffffc010ad1000) size=(0x1000) [ 10.474896] Get Index(15-INST2_CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18084000) vir_addr=(0xffffffc010ad3000) size=(0x1000) [ 10.485826] Get Index(16-CONN_SEMAPHORE_BASE) phy_addr(0x18070000) vir_addr=(0xffffffc010b60000) size=(0x10000) [ 10.495889] Get Index(17-CONN_AFE_CTL_BASE) phy_addr(0x18003000) vir_addr=(0xffffffc010ad5000) size=(0x1000) [ 10.505691] Get Index(18-CONN_AFE_CTL_2ND_BASE) phy_addr(0x18083000) vir_addr=(0xffffffc010ad7000) size=(0x1000) [ 10.515841] Get Index(19-WF_TOP_SLPPROT_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010b80000) size=(0x10000) [ 10.526163] Get Index(20-WF_TOP_CFG_BASE) phy_addr(0x184b0000) vir_addr=(0xffffffc010ad9000) size=(0x1000) [ 10.535792] Get Index(21-WF_MCU_CONFIG_LS_BASE) phy_addr(0x184f0000) vir_addr=(0xffffffc010adb000) size=(0x1000) [ 10.545940] Get Index(22-WF_MCU_BUS_CR_BASE) phy_addr(0x18400000) vir_addr=(0xffffffc010add000) size=(0x1000) [ 10.555829] Get Index(23-WF_MCUSYS_INFRA_BUS_FULL_U_DEBUG_CTRL_AO_BASE) phy_addr(0x18500000) vir_addr=(0xffffffc010adf000) size=(0x1000) [ 10.568059] Get Index(24-WF_TOP_CFG_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010ba0000) size=(0x10000) [ 10.578266] eeFlashId: 0x7986, EEPROM_content_valid = 1 [ 10.578646] conninfra@(consys_plt_hw_init:221) tx_stream = 0x4, rx_stream = 0x4, band0_pa_type = 0x3, band1_pa_type = 0x3 [ 10.595741] conninfra@(consys_plt_hw_init:230) adie_cfg_type = 2, one_adie_dbdc = 0 [ 10.603382] [emi_mng_init] gConEmiPhyBase = [0x4fc00000] size = [0x100000] fw size = [0x100000] ops=[000000005f17f150] [ 10.614123] conninfra@(mtk_conninfra_drv_init:650) After platform_driver_register [ 10.621852] ConnInfra Dev: init (0) [ 10.626820] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000) [ 10.636628] conninfra@(consys_bus_clock_ctrl:485) drv=[4] conninfra_bus_clock_wpll=[0]->[16] enable [ 10.645654] conninfra@(connsys_d_die_cfg:530) D-die efuse: 0x00000000 [ 10.653109] conninfra@(_connsys_a_die_chip_id_confirm:1915) adie_idx[0]: A-die CHIP ID = 0x7976, HW Version = 0x8a20 [ 10.664613] conninfra@(_connsys_a_die_chip_id_confirm:1915) adie_idx[1]: A-die CHIP ID = 0x7976, HW Version = 0x8a20 [ 10.677124] conninfra@(consys_spi_write_nolock:670) addr = 0x0a00, val = 0xffffffff [ 10.685764] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 10.695410] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x00000000 [ 10.705056] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x43a60000 [ 10.718730] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b2, 0x00000000] [ 10.730230] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 10.739877] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a6003a [ 10.749523] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63a7003a [ 10.763196] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b2, 0x00000000] [ 10.774696] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 10.784342] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a7003a [ 10.793989] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63ac003a [ 10.807663] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b2, 0x00000000] [ 10.819162] conninfra@(consys_spi_write_nolock:670) addr = 0x0038, val = 0x4a563b00 [ 10.827805] conninfra@(consys_spi_write_nolock:670) addr = 0x065c, val = 0x1d59080f [ 10.836444] conninfra@(consys_spi_write_nolock:670) addr = 0x0664, val = 0x34c00fe0 [ 10.846094] conninfra@(consys_spi_write_nolock:670) addr = 0x0a00, val = 0xffffffff [ 10.854734] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 10.864380] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x00000000 [ 10.874025] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x43a60000 [ 10.887700] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008800bf, 0x00000000] [ 10.899199] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 10.908845] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a6003a [ 10.918492] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63a7003a [ 10.932165] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008800bf, 0x00000000] [ 10.943665] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 10.953311] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a7003a [ 10.962957] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63ac003a [ 10.976631] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008800bf, 0x00000000] [ 10.988130] conninfra@(consys_spi_write_nolock:670) addr = 0x0038, val = 0x4a563b00 [ 10.996770] conninfra@(consys_spi_write_nolock:670) addr = 0x065c, val = 0x1d59080f [ 11.005410] conninfra@(consys_spi_write_nolock:670) addr = 0x0664, val = 0x34c00fe0 [ 11.014051] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x88888005 [ 11.023649] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x00000005 [ 11.032290] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x88888005 [ 11.041888] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x00000005 [ 11.050467] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000) [ 11.060268] conninfra@(_consys_hw_conninfra_wakeup:470) conninfra_wakeup refcnt=[0]->[1] wakeup!! [ 11.069125] conninfra@(_consys_hw_conninfra_sleep:490) conninfra_sleep refcnt=[1]->[0] sleep!! [ 11.077713] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[0] CONNINFRA=[1] [ 11.088601] Button Hotplug driver version 0.4.1 [ 11.094558] mediatek_soc_hnat 15100000.hnat: wan = eth1 [ 11.099790] mediatek_soc_hnat 15100000.hnat: lan = eth0 [ 11.105001] mediatek_soc_hnat 15100000.hnat: ppd = eth0 [ 11.110212] get_vlan_if_in_br:51 dev_get_by_name failed. [ 11.115509] mediatek_soc_hnat 15100000.hnat: gmac num = 2 [ 11.120891] mediatek_soc_hnat 15100000.hnat: ppe num = 1 [ 11.126538] mediatek_soc_hnat 15100000.hnat: PPE0 entry number = 8192 [ 11.163368] mediatek_soc_hnat 15100000.hnat: PPE0 hwnat start [ 11.187396] hnat roaming work enable [ 11.193387] warp_module_init(): module init and register callback for warp [ 11.200287] create warp_ctrl ok!!! [ 11.203709] wed_get_slot_map(): assign slot_id:0 for entry: 0! [ 11.209536] wed_get_slot_map(): assign slot_id:1 for entry: 1! [ 11.215712] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 11.230184] init: - preinit - [ 11.388576] mtk_soc_eth 15100000.ethernet: [mtk_open][2701] name:eth0 dma_refcnt:0 [ 11.398944] mtk_soc_eth 15100000.ethernet: [mtk_open][2708] name:eth0 dma_refcnt:0 [ 11.406591] mtk_soc_eth 15100000.ethernet: [mtk_open][2737] name:eth0 dma_refcnt:1 [ 11.414229] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 11.422528] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 14.490612] mount_root: mounting /dev/root [ 14.758424] ubi1: attaching mtd10 [ 14.915195] ubi1: scanning is finished [ 14.923637] ubi1: attached mtd10 (name "overlay", size 50 MiB) [ 14.929459] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 14.936313] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 14.943082] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 14.950023] ubi1: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0 [ 14.956010] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 14.963211] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 2050416285 [ 14.972318] ubi1: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 19 [ 14.981516] ubi1: background thread "ubi_bgt1d" started, PID 936 UBI device number 1, total 400 LEBs (50790400 bytes, 48.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) ubimkvol: error!: UBI device doe[ 15.009571] UBIFS (ubi1:0): Mounting in unauthenticated mode s not have free [ 15.015824] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 947 logical eraseblocks [ 15.039418] UBIFS (ubi1:0): recovery needed [ 15.148705] UBIFS (ubi1:0): recovery completed [ 15.153181] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "data" [ 15.160385] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 15.170275] UBIFS (ubi1:0): FS size: 46600192 bytes (44 MiB, 367 LEBs), journal size 2285568 bytes (2 MiB, 18 LEBs) [ 15.180683] UBIFS (ubi1:0): reserved for root: 2201041 bytes (2149 KiB) [ 15.187278] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID D02C2546-844B-49D9-96EE-E497C2A23542, small LPT model [ 15.205708] urandom-seed: Seed file not found (/etc/urandom.seed) do_mount_bind_etc... [ 15.404888] procd: - early - [ 15.407799] procd: - watchdog - [ 15.920584] procd: - watchdog - [ 15.923826] procd: - ubus - [ 15.976693] procd: - init - /etc/rc.d/S00sysfixtime: Tue Aug 30 15:31:29 UTC 2022 /etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/net_cls failed: Resource busy [ 16.072839] kmodloader: loading kernel modules from /etc/modules.d/* [ 16.084797] l2tp_core: L2TP core driver, V2.0 [ 16.089709] l2tp_netlink: L2TP netlink interface [ 16.094812] gre: GRE over IPv4 demultiplexor driver [ 16.100430] ip_gre: GRE over IPv4 tunneling driver [ 16.107779] ip6_gre: GRE over IPv6 tunneling driver [ 16.125687] u32 classifier [ 16.128407] input device check on [ 16.922935] mt_wifi: module license 'Proprietary' taints kernel. [ 16.928959] Disabling lock debugging due to kernel taint [ 16.965738] conninfra@(conninfra_pwr_on:120) [conninfra_pwr_on] drv=[3] [ 16.973294] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000) [ 16.991138] Adie Type: 0x7976 [ 16.991139] SKU Type: 6000 [ 16.995050] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[1] CONNINFRA=[1] [ 17.009108] WiFi@C12L1,get_dbg_setting_by_profile() 5238: debug level setting=INDEX0_debug_level not found!! [ 17.018933] WiFi@C12L1,get_dbg_setting_by_profile() 5261: debug option setting=INDEX0_debug_option not found!! [ 17.028973] mt_rbus 0000:00:00.0: runtime IRQ mapping not provided by arch [ 17.041091] mt7986_init()--> [ 17.044002]  sku:0xf, ADIE=MT7976  [ 17.048346] <--mt7986_init() [ 17.051237] RtmpRaDevCtrlInit(): MCS_LUT not used becasue MacTb size(544) > 128! [ 17.058715] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX1 [ 17.066016] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX2 [ 17.073316] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX3 [ 17.080617] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX4 [ 17.087917] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX5 [ 17.095218] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX6 [ 17.102518] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX7 [ 17.109818] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX8 [ 17.117119] WiFi@C12L1,match_index_by_chipname() 507: not find chip name INDEX9 [ 17.124408] WiFi@C12L2,match_index_by_chipname() 512: Not find slot id, back to old rule. [ 17.132650] msta_ifname not found [ 17.142899] -->mtfwd_init(ver:2.0) [ 17.142945] <-- [ 17.146964] mtk_warp_proxy: module uses symbols from proprietary module mt_wifi, inheriting taint. [ 17.173662] ipt: xt_cgroup_MARK installed ok. [ 17.184828] xt_time: kernel timezone is -0000 [ 17.190742] PPP generic driver version 2.4.2 [ 17.195535] PPP MPPE Compression module registered [ 17.200790] NET: Registered protocol family 24 [ 17.205664] PPTP driver version 0.8.5 [ 17.210334] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 17.216061] kmodloader: done loading kernel modules from /etc/modules.d/* /etc/rc.d/S19dnsmasq: cp: can't stat '/etc/dnsmasq.d/*': No such file or directory /etc/rc.d/S19dnsmasq: sh: out of range /etc/rc.d/S19dnsmasq: sh: out of range [ 18.832993] tcp_life = 30 [ 18.835699] fin_life = 30 [ 18.838356] udp_life = 30 [ 18.841001] Binding Threshold =5 [ 20.427358] hook is going to be disabled ! [ 20.462329] hook is going to be enabled ! [ 20.485816] hook is going to be enabled ! /etc/rc.d/S21nginx: start fcgi-cgi by spawn-fcgi. /etc/rc.d/S21nginx: start nginx ok. /etc/rc.d/S49messagingagent.sh: start messagingagent ok. [ 20.756066] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 20.761971] mtk_soc_eth 15100000.ethernet: [mtk_stop][2800] name:eth0 dma_refcnt:1 [ 20.769683] mtk_soc_eth 15100000.ethernet: [mtk_stop][2804] name:eth0 dma_refcnt:0 [ 20.916860] mtk_soc_eth 15100000.ethernet: [mtk_open][2701] name:eth0 dma_refcnt:0 [ 20.928149] mtk_soc_eth 15100000.ethernet: [mtk_open][2708] name:eth0 dma_refcnt:0 [ 20.935811] mtk_soc_eth 15100000.ethernet: [mtk_open][2737] name:eth0 dma_refcnt:1 [ 20.943469] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 20.951796] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 20.955708] br-lan: port 1(eth0.1) entered blocking state [ 20.965842] br-lan: port 1(eth0.1) entered disabled state [ 20.971451] device eth0.1 entered promiscuous mode [ 20.976260] device eth0 entered promiscuous mode [ 20.981189] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 20.987916] br-lan: port 1(eth0.1) entered blocking state [ 20.993353] br-lan: port 1(eth0.1) entered forwarding state [ 21.002600] br-lan: port 2(eth0.2) entered blocking state [ 21.008028] br-lan: port 2(eth0.2) entered disabled state [ 21.013718] device eth0.2 entered promiscuous mode [ 21.018627] br-lan: port 2(eth0.2) entered blocking state [ 21.024040] br-lan: port 2(eth0.2) entered forwarding state [ 21.031390] br-lan: port 3(eth0.3) entered blocking state [ 21.036792] br-lan: port 3(eth0.3) entered disabled state [ 21.042656] device eth0.3 entered promiscuous mode [ 21.047592] br-lan: port 3(eth0.3) entered blocking state [ 21.053019] br-lan: port 3(eth0.3) entered forwarding state [ 21.061026] br-lan: port 4(eth0.4) entered blocking state [ 21.066468] br-lan: port 4(eth0.4) entered disabled state [ 21.072061] device eth0.4 entered promiscuous mode [ 21.076981] br-lan: port 4(eth0.4) entered blocking state [ 21.082390] br-lan: port 4(eth0.4) entered forwarding state [ 21.089804] br-lan: port 5(eth0.6) entered blocking state [ 21.095269] br-lan: port 5(eth0.6) entered disabled state [ 21.100900] device eth0.6 entered promiscuous mode [ 21.105881] br-lan: port 5(eth0.6) entered blocking state [ 21.111304] br-lan: port 5(eth0.6) entered forwarding state [ 21.141883] mtk_soc_eth 15100000.ethernet: [mtk_open][2701] name:eth1 dma_refcnt:1 [ 21.149606] mtk_soc_eth 15100000.ethernet: [mtk_open][2737] name:eth1 dma_refcnt:2 [ 21.157273] mtk_soc_eth 15100000.ethernet eth1: configuring for fixed/2500base-x link mode [ 21.165658] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 21.209779] hnat_priv ppd = eth0.6 [ 21.308666] WiFi@C01L2,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 21.317024] msta_ifname not found [ 21.320991] warp_cap_support(): chip_id=7986 is in WHNAT support list [ 21.327436] warp_entry_acquire(): bus slot:0, hook to WARP, entry id=0, entry: 00000000f4abf896 [ 21.336143] client_hif_specific_get(): hw->base_phy_addr 0x18000000!! [ 21.342748] warp_entry_get_by_pdev(): return entry[0] [ 21.347984] warp_msg_register():warp,pid,2906,id,0,wed_idx,0 [ 21.353738] wed_init(0): res_start = 0x15010000, size = 1000, irq=6,base_addr=0xffffffc01120b000 [ 21.363009] wed_ring_init(): wed tx ring init result = 0 [ 21.369023] wed_ring_init(): wed rx ring init result = 0 [ 21.378966] GetEntryFromFreeList: allocated new pool [ 21.385744] GetEntryFromFreeList: allocated new pool [ 21.392376] GetEntryFromFreeList: allocated new pool [ 21.398635] GetEntryFromFreeList: allocated new pool [ 21.406045] create wed ok!!! [ 21.409022] wdma_init(): wdma(0) base_addr=0xffffffc01128d800, base_phy_addr=0x15104800 [ 21.417872] warp_woif_bus_init_hw(): bus:000000008d656138, txring: 20, pa: 0x00000000546b8000, 0x00000000546b8000, 24, 28, 3c [ 21.429238] warp_woif_bus_init_hw(): bus:000000008d656138, rxring: 50, pa: 0x00000000546ba000, 0x00000000546ba000, 54, 58, 6c [ 21.440589] get_region_info(): wed_idx = 0, base_addr = 0x000000004a084e42, size = 0x40000, res.start = 0x4fd00000, shared:0 [ 21.451837] get_region_info(): wed_idx = 0, base_addr = 0x00000000ab583308, size = 0x8000, res.start = 0x151e0000, shared:0 [ 21.463024] get_region_info(): wed_idx = 0, base_addr = 0x000000009dd17c6b, size = 0x240000, res.start = 0x4fd80000, shared:1 [ 21.474359] get_region_info(): wed_idx = 0, base_addr = 0x00000000068dd5be, size = 0x1000, res.start = 0x15194000, shared:0 [ 21.485480] warp_fwdl_mcu_mode(): mcu mode, need fwdl [ 21.496498] ########## WO Firmware ########## [ 21.500878] Chip ID: 0x0000 [ 21.503667] ECO version:0 [ 21.506280] Version: DEV_000000 [ 21.509427] Build date: 20220519213044 [ 21.513184] Total region:3 [ 21.515888] ################################# [ 21.520243] Parsing tailer region 0 [ 21.523723] Target address: 0x151e0000 [ 21.527548] Download size: 20400 [ 21.530875] Parsing tailer region 1 [ 21.534368] Target address: 0x4fd00000 [ 21.538219] Download size: 87072 [ 21.541621] Parsing tailer region 2 [ 21.545125] Target address: 0x4fd80000 [ 21.548970] Download size: 2283984 [ 21.554631] warp_fwdl_ready_check_mcu_mode(): waiting for wocpu [ 21.580521] warp_fwdl_ready_check_mcu_mode(): wocpu is ready [ 21.586250] warp_woctrl_init_state(), wo_state: WO_STATE_ENABLE [ 21.592191] wo_proc_init done 00000000585998e4 [ 21.596728] wo_exep_proc_init done 00000000585998e4 [ 21.601740] wo_exception_init(0): exp log= 0x00000000f709e1bc, phy_addr= 0x0000000054360000 size= 32768 [ 21.611399] warp_probe(): probe fail since warp is full! [ 21.616750] warp_dev0: probe of 15010000.wed2 failed with error -1 [ 21.627476] WiFi@C02L1,HwCtrlInit() 500: ser_init() return NDIS_STATUS_FAILURE [ 21.693491] IFNAME[0]=wl1 [ 21.696389] IFNAME[1]=wl14 [ 21.699158] IFNAME[2]=wl13 [ 21.702041] IFNAME[3]=wl0 [ 21.704818] IFNAME[4]=wl5 [ 21.707573] IFNAME[5]=wl9 [ 21.710313] IFNAME[6]=wl15 [ 21.713133] RTMPSetProfileParameters(): Mbssid[0] miwifi_mesh = 0 [ 21.719237] RTMPSetProfileParameters(): Mbssid[1] miwifi_mesh = 0 [ 21.725348] RTMPSetProfileParameters(): Mbssid[2] miwifi_mesh = 0 [ 21.731443] RTMPSetProfileParameters(): Mbssid[3] miwifi_mesh = 0 [ 21.737551] RTMPSetProfileParameters(): Mbssid[4] miwifi_mesh = 0 [ 21.743640] RTMPSetProfileParameters(): Mbssid[5] miwifi_mesh = 0 [ 21.749735] RTMPSetProfileParameters(): Mbssid[6] miwifi_mesh = 0 [ 21.755923] RTMPSetProfileParameters(): Mbssid[0] backhaul = 0 [ 21.761762] RTMPSetProfileParameters(): Mbssid[1] backhaul = 0 [ 21.767593] RTMPSetProfileParameters(): Mbssid[2] backhaul = 0 [ 21.773435] RTMPSetProfileParameters(): Mbssid[3] backhaul = 0 [ 21.779277] RTMPSetProfileParameters(): Mbssid[4] backhaul = 1 [ 21.785118] RTMPSetProfileParameters(): Mbssid[5] backhaul = 0 [ 21.790952] RTMPSetProfileParameters(): Mbssid[6] backhaul = 0 [ 21.796894] RTMPSetProfileParameters(): Mbssid[0] mimesh_ver = 0 [ 21.802895] RTMPSetProfileParameters(): Mbssid[1] mimesh_ver = 0 [ 21.808889] RTMPSetProfileParameters(): Mbssid[2] mimesh_ver = 0 [ 21.814895] RTMPSetProfileParameters(): Mbssid[3] mimesh_ver = 4 [ 21.820896] RTMPSetProfileParameters(): Mbssid[4] mimesh_ver = 4 [ 21.826899] RTMPSetProfileParameters(): Mbssid[5] mimesh_ver = 0 [ 21.832898] RTMPSetProfileParameters(): Mbssid[6] mimesh_ver = 0 [ 21.838994] RTMPSetProfileParameters(): mesh_apmac = 24:CF:24:C3:BA:E4 [ 21.845629] RTMPSetProfileParameters(): mimesh_aplimit = 9 [ 21.851209] RTMPSetProfileParameters(): mimesh_id = 0x355e73f9 [ 21.857123] RTMPSetProfileParameters: mesh_model = RB06 [ 21.862801] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS0 PhyMode=78 [ 21.869409] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS1 PhyMode=78 [ 21.876009] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS2 PhyMode=78 [ 21.882610] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS3 PhyMode=177 [ 21.889302] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS4 PhyMode=177 [ 21.896006] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS5 PhyMode=177 [ 21.902699] WiFi@C12L1,RTMPWirelessModeCfg() 587: Init: BSS6 PhyMode=177 [ 21.909628] WiFi@C23L2,auto_ch_select_set_cfg() 3398: BandIdx0, AutoChannelAtBootup=1, AutoChannelAlg = 3 [ 21.919180] WiFi@C23L2,auto_ch_select_set_cfg() 3398: BandIdx1, AutoChannelAtBootup=1, AutoChannelAlg = 3 [ 21.965317] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=0, Desired MFPC=0 [ 21.972727] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=1, Desired MFPC=0 [ 21.980115] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=2, Desired MFPC=0 [ 21.987516] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=3, Desired MFPC=0 [ 21.994902] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=4, Desired MFPC=0 [ 22.002284] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=5, Desired MFPC=0 [ 22.009705] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=6, Desired MFPC=0 [ 22.018471] WiFi@C12L1,RTMPSetProfileParameters() 8263: wl1, QoSMgmtCapa=0 [ 22.025352] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0 [ 22.032481] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0 [ 22.039630] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0 [ 22.046772] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0 [ 22.053910] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0 [ 22.061049] WiFi@C12L1,RTMPSetProfileParameters() 8263: (null), QoSMgmtCapa=0 [ 22.072873] WiFi@C12L1,rtmp_read_ap_client_from_file() 1566: APCLI[0] ApCliMuMimoDlEnable = 0 [ 22.081401] WiFi@C12L1,rtmp_read_ap_client_from_file() 1566: APCLI[1] ApCliMuMimoDlEnable = 0 /etc/rc.d/S60iwe[ 22.090050] WiFi@C12L1,rtmp_read_ap_client_from_file() 1585: APCLI[0] ApCliMuMimoUlEnable = 0 ventd: iwevent-c[ 22.099835] WiFi@C12L1,rtmp_read_ap_client_from_file() 1585: APCLI[1] ApCliMuMimoUlEnable = 0 all start ok [ 22.111160] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 22.122406] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48 [ 22.130899] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 22.142124] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48 [ 22.207923] wdma_dma_ctrl(): WDMA_GLO_CFG=50404e70, txrx = 0 [ 22.219472] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e70, txrx = 0 [ 22.233710] warp_tx_ring_init_hw(): configure ring 0 setting [ 22.239381] warp_tx_ring_init_hw(): wed:00000000c8bd214a wifi:000000001ef037cc: 24420=5cb38000,24424=2048,24428=0 [ 22.249646] warp_tx_ring_init_hw(): configure ring 1 setting [ 22.255334] warp_tx_ring_init_hw(): wed:00000000c8bd214a wifi:000000001ef037cc: 24430=55c90000,24434=2048,24438=0 [ 22.265707] set_rrocfg,0 [ 22.291117] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e74, txrx = 3 [ 22.296970]  sku:0xf, ADIE=MT7976  [ 22.301359] using E1 ROM patch [ 22.304424] using E1 RAM [ 22.306957] current sync CR = 0x1 [ 22.310271] Built date: 20220519212529a [ 22.314213] Platform: ALPS [ 22.317024] HW/SW version: 0x8a108a10 [ 22.320788] Patch version: 0xffffffff [ 22.330881] current sync CR = 0x1 [ 22.334219] Chip ID: 0x0f [ 22.336954] Eco version: 0x00 [ 22.340044] Region number: 0x0b [ 22.343261] Format version: 0x02 [ 22.346577] Format flag: 0x01 [ 22.349627] Ram version: ____000000 [ 22.353216] Built date: 20220519212633 [ 22.357081] Common crc: 0xb8995b85 [ 22.360580] Release info: header tag = 0, total length = 108 [ 22.366343] tag 1, padding length = 1, tag length = 103 [ 22.371655] payload: t-neptune-main-2111-7986-imp_backup_wk2213-MT7986_E1_ASIC_ROM_RAM_REBB_IMP_BACKUP_WK2213-20220519212500 [ 22.401527] Chip ID: 0x00 [ 22.404239] Eco version: 0x00 [ 22.407277] Region number: 0x03 [ 22.410499] Format version: 0x02 [ 22.413803] Format flag: 0x01 [ 22.416845] Ram version: DEV_000000 [ 22.420411] Built date: 20220519213028 [ 22.424238] Common crc: 0x962f9340 [ 22.427715] Release info: header tag = 0, total length = 0 [ 22.527065] current sync CR = 0x7 [ 22.530394] efuse_probe: efuse = deaddead [ 22.538987]  sku:0xf, ADIE=MT7976  [ 22.544927] WiFi@C02L1,is_cal_free_ic() 1004: is_cal_free_ic(1004) offset:1000, 0,0  [ 22.553354]  sku:0xf, ADIE=MT7976  [ 22.571560]  sku:0xf, ADIE=MT7976  [ 22.589943] WiFi@C02L1,is_cal_free_ic() 1023:  iCal free [ 22.595934]  sku:0xf, ADIE=MT7976  [ 26.458989] WiFi@C17L1,RTMPReadTxPwrPerRate() 450: (450): Don't Support this now! [ 26.466505] WiFi@C01L1,AntCfgInit() 3020: Not support for HIF_MT yet! [ 26.486540] ch_switch_monitor_state_machine_init:: enter [ 26.491851] ch_switch_monitor_cfg_reset:: enter [ 26.496375] ch_switch_monitor_cfg_reset:: enter [ 26.501199] WiFi@C17L1,tx_pwr_comp_init() 641: NotSupportYet! [ 26.507091] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 26.512566] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 26.518126] WiFi@C14L1,IPMacTable_init() 348: IPMacTable already inited! [ 26.544941] wdma_dma_ctrl(): WDMA_GLO_CFG=58804e75, txrx = 3 [ 26.550676] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 26.556160] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 26.561589] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 26.571484] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13447: DAT config band(0) cck_timeout Fail! [ 26.580163] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 26.590054] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13458: DAT config band(0) ofdm_timeout Fail! [ 26.598818] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 26.608710] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13469: DAT config band(0) ofdma_timeout Fail! [ 26.617561] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 26.627452] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13447: DAT config band(1) cck_timeout Fail! [ 26.636131] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 26.646023] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13458: DAT config band(1) ofdm_timeout Fail! [ 26.654787] WiFi@C00L1,set_ack_timeout_mode_byband() 13359: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 26.664678] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13469: DAT config band(1) ofdma_timeout Fail! [ 26.673584] mbss_create_vif: ifidx(1) idbss(1) final_name(wl14) [ 26.679989] mbss_create_vif: ifidx(2) idbss(2) final_name(wl13) [ 26.686732] mbss_create_vif: ifidx(1) idbss(4) final_name(wl5) [ 26.693210] mbss_create_vif: ifidx(2) idbss(5) final_name(wl9) [ 26.699584] mbss_create_vif: ifidx(3) idbss(6) final_name(wl15) [ 26.706617] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 26.714848] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 26.920495] :(op = 0) [ 26.922775] WiFi@C00L2,red_tail_drop_init() 83: red_tail_drop_init: available token:8192, whnat_en:1 [ 26.931901] WiFi@C00L1,MtCmdCr4RedSet() 913: MtCmdCr4RedSet: (ret = 0) [ 26.938416] WiFi@C00L1,SendRedCmd() 1048: SendRedCmd:(ret = 1) [ 26.944358] WiFi@C01L2,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 26.952348] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 0 [ 26.957922] WiFi@C23L1,DfsBuildChannelList() 3295: [RDM]: wdev is not 5G. [ 26.964723] [RadarStateCheck] Zero Wait State: 0 [ 26.969328] phy_freq_adjust : no prim_ch value for adjust! [ 26.974998] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] [ 26.982991] wdev_attr_update(): wdevId0 = 24:cf:24:c3:ba:e5 [ 26.988573] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band0 group_idx[0]=0, bw_grp=16 omac=0 [ 26.997688] WiFi@C23L1,HcGetBandByChannel() 1102: No hdev parking on channel:0, just return a default band_idx 0! [ 27.007935] WiFi@C02L2,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn [ 27.014728] WiFi@C00L2,ApAutoChannelAtBootUp() 289: -----------------> [ 27.021336] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 27.026812] WiFi@C03L1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 27.032405] WiFi@C08L1,UpdateBeaconHandler() 1979: wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x108/0x490 [mt_wifi])!! [ 27.044711] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=1, ctrl_ch2=0, cent_ch=1 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 27.291616] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=2, ctrl_ch2=0, cent_ch=2 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 27.535623] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=3, ctrl_ch2=0, cent_ch=3 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 27.779613] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=4, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.023629] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=5, ctrl_ch2=0, cent_ch=5 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.267614] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=6, ctrl_ch2=0, cent_ch=6 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.511646] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=7, ctrl_ch2=0, cent_ch=7 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.755610] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=8, ctrl_ch2=0, cent_ch=8 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.999614] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=9, ctrl_ch2=0, cent_ch=9 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 29.243607] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=10, ctrl_ch2=0, cent_ch=10 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 29.487609] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=11, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 29.731791] WiFi@C08L1,UpdateBeaconHandler() 1979: wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x2d0/0x490 [mt_wifi])!! [ 29.744036] WiFi@C23L2,SelectClearChannelBusyTime() 1845: ==================================================================== [ 29.755408] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 1 : Busy Time = 9330, Skip Channel = FALSE, BwCap = TRUE [ 29.766774] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 2 : Busy Time = 5782, Skip Channel = FALSE, BwCap = TRUE [ 29.778140] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 3 : Busy Time = 14151, Skip Channel = FALSE, BwCap = TRUE [ 29.789506] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 4 : Busy Time = 12141, Skip Channel = FALSE, BwCap = TRUE [ 29.800872] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 5 : Busy Time = 6450, Skip Channel = FALSE, BwCap = TRUE [ 29.812236] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 6 : Busy Time = 6668, Skip Channel = FALSE, BwCap = TRUE [ 29.823602] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 7 : Busy Time = 2381, Skip Channel = FALSE, BwCap = TRUE [ 29.834973] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 8 : Busy Time = 2626, Skip Channel = FALSE, BwCap = TRUE [ 29.846340] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 9 : Busy Time = 2291, Skip Channel = FALSE, BwCap = TRUE [ 29.857705] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 10 : Busy Time = 4446, Skip Channel = FALSE, BwCap = TRUE [ 29.869071] WiFi@C23L2,SelectClearChannelBusyTime() 1851: Channel 11 : Busy Time = 7567, Skip Channel = FALSE, BwCap = TRUE [ 29.880435] WiFi@C23L2,SelectClearChannelBusyTime() 1854: ==================================================================== [ 29.891806] WiFi@C23L2,SelectClearChannelBusyTime() 2088: Rule 3 Channel Busy time value : Select Primary Channel 9 [ 29.902219] WiFi@C23L2,SelectClearChannelBusyTime() 2090: Rule 3 Channel Busy time value : Min Channel Busy = 2291 [ 29.912545] WiFi@C23L2,SelectClearChannelBusyTime() 2095: Rule 3 Channel Busy time value : BW = 20 [ 29.921486] WiFi@C23L2,SelectClearChannelBusyTime() 2129: [SelectClearChannelBusyTime] - band0 END [ 29.930451] WiFi@C23L1,operate_loader_phy() 401: oper_radio after decision: bw(1), prim_ch(9), cen_ch_1(11), cen_ch_2(0)! [ 29.941444] WiFi@C03L2,MtCmdChannelSwitch() 2530: ctrl_chl=9, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=1, TXStream=4, RXStream=4, scan(0) [ 30.242880] WiFi@C23L1,DfsBuildChannelList() 3295: [RDM]: wdev is not 5G. [ 30.249662] WiFi@C23L2,zero_wait_dfs_switch_ch() 779: outband ch 0, ch_stat 0 [ 30.257002] WiFi@C08L2,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:0, CfgMode:0 [ 30.267532] WiFi@C15L2,APPMFInit() 133: [PMF] apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 30.275065] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 30.282608] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(0) [ 30.291206] WiFi@C01L2,wifi_sys_linkup() 1128: wdev idx = 0 [ 30.342112] WiFi@C03L1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 30.358258] WiFi@C00L1,TxCCKStreamCtrl() 21350: set wrong parameters [ 30.373576] PrintSrCmd: [ 30.373576] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.373576] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 30.387546] PrintSrCmd: [ 30.387546] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.387546] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.401514] PrintSrCmd: [ 30.401514] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.401514] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 30.415480] PrintSrCmd: [ 30.415480] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.415480] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 30.429586] main_virtual_if_open(): net_device wl1 ifindex(10) up! [ 30.430389] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0 [ 30.435756] mtk_ppe_dev_register_hook : ineterface wl1 register (1) [ 30.450129] ip_acc_add_table(534): add succ (lan: 0)! [ 30.452055] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl13 [ 30.455239] account_init succ! [ 30.461303] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 30.472682] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 30.480972] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 2 [ 30.486721] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(1), prim_ch(9), cen_ch_1(11), cen_ch_2(0)! /etc/rc.d/S77tra[ 30.498350] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] fficd: refresh i[ 30.507436] wdev_attr_update(): wdevId2 = 26:cf:24:a3:ba:e5 fname into ipaac[ 30.514384] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band0 group_idx[2]=9, bw_grp=16 omac=17 ount in [lan-dev[ 30.525066] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn 5g-wl 2.4g-wl w[ 30.533354] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: -----------------> l-guest 5g-wl-ba[ 30.541068] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) ckhaul] /etc/rc[ 30.547904] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) .d/S77trafficd: [ 30.554855] 7986@C00L1wl1,ApAutoChannelAtBootUp() 424: not A band eth0 wl0 wl1 wl2[ 30.562249] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !! wl14 wl15 wl5 [ 30.570760] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:2, CfgMode:0 /etc/rc.d/S77tra[ 30.582725] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=2, MFPC=0, MFPR=0, SHA256=0 fficd: trafficd [ 30.591879] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] start ok [ 30.600605] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(2) /etc/rc.d/S90mos[ 30.609797] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 2 quitto: /etc/r[ 30.617327] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 c.d/S90mosquitto: [ 30.635403] 7986@C00L1wl1,TxCCKStreamCtrl() 21350: set wrong parameters [ 30.651031] PrintSrCmd: [ 30.651031] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.651031] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 30.665055] PrintSrCmd: [ 30.665055] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.665055] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.679086] PrintSrCmd: [ 30.679086] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.679086] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 30.693063] PrintSrCmd: [ 30.693063] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 30.693063] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 30.707190] mbss_virtual_if_open(): net_device wl13 ifindex(19) open! [ 30.713638] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0 [ 30.720764] mtk_ppe_dev_register_hook : ineterface wl13 register (2) [ 30.727772] br-miot: port 1(wl13) entered blocking state [ 30.733090] br-miot: port 1(wl13) entered disabled state [ 30.738583] device wl13 entered promiscuous mode [ 30.743564] set_no_bcn(): net_device wl1 ifindex(10) up! [ 30.748919] set_no_bcn(): Set no beacon as:0 [ 30.753313] br-miot: port 1(wl13) entered blocking state [ 30.758644] br-miot: port 1(wl13) entered forwarding state [ 30.768028] br-lan: port 6(wl1) entered blocking state [ 30.773220] br-lan: port 6(wl1) entered disabled state [ 30.778589] device wl1 entered promiscuous mode [ 30.783269] br-lan: port 6(wl1) entered blocking state [ 30.788429] br-lan: port 6(wl1) entered forwarding state [ 30.807171] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl14 [ 30.813372] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 30.821750] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 30.830011] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 1 [ 30.835669] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(1), prim_ch(9), cen_ch_1(11), cen_ch_2(0)! /etc/rc.d/S90mos[ 30.847210] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] quitto: [ 30.856357] wdev_attr_update(): wdevId1 = 26:cf:24:93:ba:e5 [ 30.862720] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band0 group_idx[1]=10, bw_grp=16 omac=18 [ 30.872009] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn /etc/rc.d/S90mos[ 30.879304] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: -----------------> quitto: [ 30.886863] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 30.893366] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 30.899040] 7986@C00L1wl1,ApAutoChannelAtBootUp() 424: not A band [ 30.905186] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !! [ 30.912308] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:1, CfgMode:0 [ 30.923126] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=1, MFPC=0, MFPR=0, SHA256=0 [ 30.930985] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 30.938610] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(1) [ 30.947233] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 1 /etc/rc.d/S90mosquitto: /etc/rc.d/S90mosquitto: /tmp/mq/cc/xiaoqiang_ct: OK /etc/rc.d/S90mosquitto: /etc/rc.d/S90mosquitto: [ 30.998837] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 31.016069] 7986@C00L1wl1,TxCCKStreamCtrl() 21350: set wrong parameters [ 31.031742] PrintSrCmd: [ 31.031742] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 31.031742] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 31.045973] PrintSrCmd: [ 31.045973] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 31.045973] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 31.060028] PrintSrCmd: [ 31.060028] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 31.060028] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 31.074059] PrintSrCmd: [ 31.074059] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 31.074059] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [port_service] i[ 31.088327] mbss_virtual_if_open(): net_device wl14 ifindex(18) open! nit services fin[ 31.096029] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0 ish [ 31.104558] mtk_ppe_dev_register_hook : ineterface wl14 register (3) /etc/init.d/network: Command failed: Not found [ 31.137849] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl0 [ 31.143954] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 31.152333] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 31.160629] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 3 [ 31.166485] [RadarStateCheck] Zero Wait State: 0 [ 31.171151] 7986@C23L2wl1,RadarStateCheck() 292:  RD_NORMAL_MODE  [ 31.178214] phy_freq_adjust : no prim_ch value for adjust! [ 31.184024] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] [ 31.192046] wdev_attr_update(): wdevId3 = 24:cf:24:c3:ba:e6 [ 31.197682] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[3]=4, bw_grp=16 omac=0 [ 31.207994] 7986@C23L1wl1,HcGetBandByChannel() 1102: No hdev parking on channel:0, just return a default band_idx 0! [ 31.218655] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=0 RadioOn [port_service] r[ 31.225856] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: -----------------> ebuild map finis[ 31.233613] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) h [ 31.240677] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 31.246450] 7986@C23L2wl1,AutoChSelBuildChannelListFor56G() 2702: ChListNum56G = 13 [ 31.254467] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(3) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x108/0x490 [mt_wifi])!! [ 31.267093] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=36, ctrl_ch2=0, cent_ch=36 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [port_service] remove vlan finish [port_service] LIST_VID = -1 [ 31.318777] clean port 1 ifname [ 31.322004] set port 1 ifname eth0.1 [port_service] create switch vlan: switch=switch0, ports=1 6t, vid=1 [port_service] create if: eth0.1 [ 31.348747] clean port 2 ifname [ 31.351976] set port 2 ifname eth0.2 [port_service] create switch vlan: switch=switch0, ports=2 6t, vid=2 [port_service] create if: eth0.2 [ 31.383614] clean port 3 ifname [ 31.386879] set port 3 ifname eth0.3 [port_service] create switch vlan: switch=switch0, ports=3 6t, vid=3 [port_service] create if: eth0.3 [ 31.426084] clean port 4 ifname [ 31.429311] set port 4 ifname eth0.4 [port_service] create switch vlan: switch=switch0, ports=4 6t, vid=4 [port_service] create if: eth0.4 [port_service] create switch vlan: switch=switch0, ports=, vid=5 [port_service] create if: eth1.5 [port_service] create if: eth0.6 [port_service] reconfig vlan finish [ 31.523678] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=40, ctrl_ch2=0, cent_ch=40 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 31.779628] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=44, ctrl_ch2=0, cent_ch=44 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 32.035675] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=48, ctrl_ch2=0, cent_ch=48 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 32.143378] BcnCheck start after 3300 ms (wl1) [ 32.148238] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(3) bss not ready (state:0, caller:update_ap_qload_to_bcn+0xa0/0xc8 [mt_wifi])!! [ 32.291807] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(3) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x2d0/0x490 [mt_wifi])!! [ 32.304315] 7986@C23L2wl1,SelectClearChannelBusyTime() 1845: ==================================================================== [ 32.315944] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 36 : Busy Time = 43, Skip Channel = FALSE, BwCap = TRUE [ 32.327569] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 40 : Busy Time = 1918, Skip Channel = FALSE, BwCap = TRUE [ 32.339194] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 44 : Busy Time = 168, Skip Channel = FALSE, BwCap = TRUE [ 32.350824] 7986@C23L2wl1,SelectClearChannelBusyTime() 1851: Channel 48 : Busy Time = 57, Skip Channel = FALSE, BwCap = TRUE [ 32.362460] 7986@C23L2wl1,SelectClearChannelBusyTime() 1854: ==================================================================== [ 32.374094] 7986@C23L2wl1,SelectClearChannelBusyTime() 2088: Rule 3 Channel Busy time value : Select Primary Channel 36 [ 32.384852] 7986@C23L2wl1,SelectClearChannelBusyTime() 2090: Rule 3 Channel Busy time value : Min Channel Busy = 1918 [ 32.395437] 7986@C23L2wl1,SelectClearChannelBusyTime() 2095: Rule 3 Channel Busy time value : BW = 160 [ 32.404724] 7986@C23L2wl1,SelectClearChannelBusyTime() 2129: [SelectClearChannelBusyTime] - band1 END [ 32.413942] [RadarStateCheck] Zero Wait State: 0 [ 32.418551] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE  [ 32.425685] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)! [ 32.436963] new DFS channel 52 not pre dfs channel [ 32.441743] 7986@C23L2wl1,DfsCacNormalStart() 3204: [RDM] CAC 65 seconds start . Disable MAC TX [ 32.450499] 7986@C03L2wl1,MtCmdChannelSwitch() 2530: ctrl_chl=36, ctrl_ch2=0, cent_ch=50 DBDCIdx=1, ChBand=1, BW=3, TXStream=4, RXStream=4, scan(0) [ 32.500015] 7986@C23L2wl1,zero_wait_dfs_switch_ch() 779: outband ch 0, ch_stat 0 [ 32.507408] 7986@C23L2wl1,zero_wait_dfs_switch_ch() 786: bDedicatedZeroWaitDefault == 0 [ 32.515627] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:3, CfgMode:0 [ 32.526411] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=3, MFPC=0, MFPR=0, SHA256=0 [ 32.534202] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 32.541762] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(3) [ 32.550358] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 3 [ 32.601584] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 32.629073] PrintSrCmd: [ 32.629073] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 32.629073] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 32.643047] PrintSrCmd: [ 32.643047] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 32.643047] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 32.657018] PrintSrCmd: [ 32.657018] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 32.657018] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 32.670987] PrintSrCmd: [ 32.670987] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 32.670987] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 32.685093] mbss_virtual_if_open(): net_device wl0 ifindex(20) open! [ 32.685896] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0 [ 32.691443] mtk_ppe_dev_register_hook : ineterface wl0 register (4) [ 32.711127] br-lan: port 7(wl0) entered blocking state [ 32.716294] br-lan: port 7(wl0) entered disabled state [ 32.721644] device wl0 entered promiscuous mode [ 32.726308] br-lan: port 7(wl0) entered blocking state [ 32.731457] br-lan: port 7(wl0) entered forwarding state [ 32.751222] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl5 [ 32.757213] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 32.765668] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 32.773946] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 4 [ 32.779686] [RadarStateCheck] Zero Wait State: 0 [ 32.779896] [wandt filter] init success! [ 32.784319] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE  [ 32.795382] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=4  [ 32.803481] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)! [ 32.815031] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] [ 32.823038] wdev_attr_update(): wdevId4 = 26:cf:24:c3:ba:e5 [ 32.828640] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[4]=25, bw_grp=16 omac=17 [ 32.839205] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=1 RadioOn [ 32.846480] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: -----------------> [ 32.853370] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 32.859112] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 32.864758] 7986@C00L1wl1,ApAutoChannelAtBootUp() 418: zero-wait DFS is not enabled [ 32.872396] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !! [ 32.879474] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:4, CfgMode:0 [ 32.890258] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=4, MFPC=0, MFPR=0, SHA256=0 [ 32.898083] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 32.905640] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(4) [ 32.914239] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 4 [ 32.965547] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 32.993551] PrintSrCmd: [ 32.993551] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 32.993551] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.007527] PrintSrCmd: [ 33.007527] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.007527] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 33.021500] PrintSrCmd: [ 33.021500] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.021500] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.035473] PrintSrCmd: [ 33.035473] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.035473] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.049560] mbss_virtual_if_open(): net_device wl5 ifindex(21) open! [ 33.050379] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0 [ 33.055905] mtk_ppe_dev_register_hook : ineterface wl5 register (5) [ 33.073933] br-lan: port 8(wl5) entered blocking state [ 33.079106] br-lan: port 8(wl5) entered disabled state [ 33.084468] device wl5 entered promiscuous mode [ 33.089121] br-lan: port 8(wl5) entered blocking state [ 33.094282] br-lan: port 8(wl5) entered forwarding state [ 33.111953] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl9 [ 33.117875] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 33.126214] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 33.134466] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 5 [ 33.140059] [RadarStateCheck] Zero Wait State: 0 [ 33.144675] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE  [ 33.151794] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=4  [ 33.159871] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)! [ 33.171356] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] [ 33.179349] wdev_attr_update(): wdevId5 = 26:cf:24:d3:ba:e5 [ 33.184928] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[5]=26, bw_grp=16 omac=18 [ 33.195355] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=1 RadioOn [ 33.202411] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: -----------------> [ 33.209277] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 33.215011] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 33.220667] 7986@C00L1wl1,ApAutoChannelAtBootUp() 418: zero-wait DFS is not enabled [ 33.228307] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !! [ 33.235386] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:5, CfgMode:0 [ 33.246172] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=5, MFPC=0, MFPR=0, SHA256=0 [ 33.253987] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 33.261535] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(5) [ 33.270131] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 5 [ 33.276463] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 33.304505] PrintSrCmd: [ 33.304505] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.304505] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.318480] PrintSrCmd: [ 33.318480] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.318480] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 33.332470] PrintSrCmd: [ 33.332470] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.332470] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.346448] PrintSrCmd: [ 33.346448] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.346448] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.360610] mbss_virtual_if_open(): net_device wl9 ifindex(22) open! [ 33.361377] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0 [ 33.366984] mtk_ppe_dev_register_hook : ineterface wl9 register (6) [ 33.383277] br-lan: port 9(wl9) entered blocking state [ 33.388440] br-lan: port 9(wl9) entered disabled state [ 33.393755] device wl9 entered promiscuous mode [ 33.398335] br-lan: port 9(wl9) entered blocking state [ 33.403463] br-lan: port 9(wl9) entered forwarding state [ 33.419860] 7986@C08L2wl1,mbss_virtual_if_open() 134: ===> wl15 [ 33.425864] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 33.434207] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 33.442463] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 6 [ 33.448051] [RadarStateCheck] Zero Wait State: 0 [ 33.452667] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE  [ 33.459785] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=5  [ 33.467864] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)! [ 33.479346] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] [ 33.487340] wdev_attr_update(): wdevId6 = 26:cf:24:e3:ba:e5 [ 33.492924] WiFi@C12L1,wifi_sys_open() 869: wifi_sys_open():band1 group_idx[6]=27, bw_grp=16 omac=19 [ 33.503245] 7986@C02L2wl1,AsicRadioOnOffCtrl() 2279: DbdcIdx=1 RadioOn [ 33.510302] 7986@C00L2wl1,ApAutoChannelAtBootUp() 289: -----------------> [ 33.517167] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 33.522902] 7986@C03L1wl1,MtCmdSetMacTxRx() 10214: (ret = 0) [ 33.528548] 7986@C00L1wl1,ApAutoChannelAtBootUp() 418: zero-wait DFS is not enabled [ 33.536186] 7986@C08L1wl1,ap_run_at_boot() 537:  ACS is disable !! [ 33.543295] 7986@C08L2wl1,APStartUpForMbss() 887: ===>(caller:ap_inf_open+0x140/0x4f8 [mt_wifi]), mbss_idx:6, CfgMode:0 [ 33.554087] 7986@C15L2wl1,APPMFInit() 133: [PMF] apidx=6, MFPC=0, MFPR=0, SHA256=0 [ 33.561867] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 33.569414] WiFi@C08L2,ap_link_up() 6926: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(6) [ 33.578011] 7986@C01L2wl1,wifi_sys_linkup() 1128: wdev idx = 6 [ 33.631773] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 33.659752] PrintSrCmd: [ 33.659752] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.659752] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.673727] PrintSrCmd: [ 33.673727] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.673727] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 33.687698] PrintSrCmd: [ 33.687698] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.687698] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.701664] PrintSrCmd: [ 33.701664] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 33.701664] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 33.715837] mbss_virtual_if_open(): net_device wl15 ifindex(23) open! [ 33.716580] [mtf_txpower_all_rate_info] band_idx:1 pwr:47 ChBand:5G ePAGain:0 [ 33.722273] mtk_ppe_dev_register_hook : ineterface wl15 register (7) /etc/init.d/network: Command failed: Not found [ 33.749192] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1581: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 33.757559] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1558: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 33.765832] WiFi@C01L2,wifi_sys_open() 827: wdev idx = 8 [ 33.771432] [RadarStateCheck] Zero Wait State: 0 [ 33.776045] 7986@C23L2wl1,RadarStateCheck() 258:  RD_SILENCE_MODE  [ 33.783162] 7986@C23L2wl1,RadarStateCheck() 269:  mode=2, pDot11h->RDCount=5  [ 33.791240] 7986@C23L1wl1,operate_loader_phy() 401: oper_radio after decision: bw(3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)! [ 33.802734] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xac/0x110 [mt_wifi] [ 33.810732] wdev_attr_update(): wdevId8 = 2a:cf:24:c3:ba:e6 [ 33.817730] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 33.825146] mtk_ppe_dev_register_hook : ineterface apclix0 register (8) [ 33.834750] br-lan: port 10(apclix0) entered blocking state [ 33.840450] br-lan: port 10(apclix0) entered disabled state [ 33.846194] device apclix0 entered promiscuous mode [ 33.868122] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl14 [ 33.874224] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN [ 33.882897] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(1) [ 33.892176] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(1) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!! [ 33.903816] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 1 [ 33.910722] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 33.926026] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 1 [ 33.931790] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT [ 33.940304] mbss_virtual_if_close(): net_device wl14 ifindex(18) close! [ 33.946913] extif_put_dev(wl14) [ 33.950043] mtk_ppe_dev_unregister_hook : ineterface wl14 set null (3) [ 33.971406] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl13 [ 33.977502] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN [ 33.986175] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(2) [ 33.995465] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(2) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!! [ 34.007169] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 2 [ 34.014073] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=9, ucCentChSeg0=11, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 34.029341] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 2 [ 34.035081] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT [ 34.043590] mbss_virtual_if_close(): net_device wl13 ifindex(19) close! [ 34.050191] extif_put_dev(wl13) [ 34.053320] mtk_ppe_dev_unregister_hook : ineterface wl13 set null (2) [ 34.059971] br-miot: port 1(wl13) entered disabled state [ 34.090257] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl9 [ 34.096276] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN [ 34.104949] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(5) [ 34.114229] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(5) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!! [ 34.125865] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 5 [ 34.132771] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 34.148131] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 5 [ 34.153875] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT [ 34.162386] mbss_virtual_if_close(): net_device wl9 ifindex(22) close! [ 34.168902] extif_put_dev(wl9) [ 34.171945] mtk_ppe_dev_unregister_hook : ineterface wl9 set null (6) [ 34.180619] br-lan: port 9(wl9) entered disabled state [ 34.188335] device wl9 left promiscuous mode [ 34.192794] br-lan: port 9(wl9) entered disabled state [ 34.246330] ip_acc_set_table(602): set succ(lan)! [ 34.279171] br-lan: port 1(eth0.1) entered disabled state [ 34.287967] 7986@C08L2wl1,mbss_virtual_if_close() 190: ===> wl15 [ 34.294078] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN [ 34.302807] WiFi@C08L2,ap_link_down() 6944: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(6) [ 34.312083] 7986@C08L1wl1,UpdateBeaconHandler() 1979: wdev(6) bss not ready (state:2, caller:ap_link_down+0x84/0x130 [mt_wifi])!! [ 34.323727] 7986@C01L2wl1,wifi_sys_linkdown() 1252: wdev idx = 6 [ 34.330634] 7986@C03L1wl1,bssUpdateChannel() 3734: ucPrimCh=36, ucCentChSeg0=50, ucCentChSeg1=0, BW=3, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 34.346082] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 6 [ 34.351906] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT [ 34.360427] mbss_virtual_if_close(): net_device wl15 ifindex(23) close! [ 34.363969] 7986@C09L2wl1,cntl_connect_request() 389: type=2,len=0,caller:ApCliIfUp+0x198/0x328 [mt_wifi] [ 34.367050] extif_put_dev(wl15) [ 34.376606] PrintSrCmd: [ 34.376606] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 34.376606] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 34.379705] mtk_ppe_dev_unregister_hook : ineterface wl15 set null (7) [ 34.400243] PrintSrCmd: [ 34.400243] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 34.400243] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 34.414368] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1569: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN [ 34.423056] WiFi@C01L2,wifi_sys_close() 907: wdev idx = 8 [ 34.429004] 7986@C01L2wl1,RTMP_COM_IoctlHandle() 1592: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT [ 34.437565] extif_put_dev(apclix0) [ 34.440960] mtk_ppe_dev_unregister_hook : ineterface apclix0 set null (8) [ 34.447887] br-lan: port 10(apclix0) entered disabled state [ 34.453931] br-lan: port 2(eth0.2) entered disabled state [ 34.459506] device apclix0 left promiscuous mode [ 34.464160] br-lan: port 10(apclix0) entered disabled state [ 34.491241] br-lan: port 3(eth0.3) entered disabled state [ 34.500663] br-lan: port 4(eth0.4) entered disabled state starting miwifi-roam success /etc/init.d/network: Command failed: Not found [ 34.582335] SetThermalProtectDisable(): band_idx: 0, protection_type: 1, trigger_type: 1 [ 34.591632] SetThermalProtectDisable(): band_idx: 1, protection_type: 1, trigger_type: 1 [ 34.600889] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 0, duty: 100 [ 34.608983] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 1, duty: 70 [ 34.617029] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 2, duty: 50 [ 34.624985] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 3, duty: 10 [ 34.632982] SetThermalProtectEnable(): band_idx: 0, protection_type: 1, trigger_type: 1 [ 34.640992] SetThermalProtectEnable(): trigger_temp: 106, restore_temp: 101, recheck_time: 5 [ 34.650430] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 0, duty: 100 [ 34.658501] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 1, duty: 70 [ 34.666397] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 2, duty: 50 [ 34.674366] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 3, duty: 10 [ 34.682291] SetThermalProtectEnable(): band_idx: 1, protection_type: 1, trigger_type: 1 [ 34.690296] SetThermalProtectEnable(): trigger_temp: 106, restore_temp: 101, recheck_time: 5 [ 34.903383] BcnCheck start after 800 ms (wl1) [ 36.419381] 7986@C13L1wl0,MlmeEnqueueWithWdev() 5579: wdev(8) state: if down! [port_service] build network finish [port_service] all services have started /etc/rc.d/S98miqos: miqos: delay 5s to wait for network ready. [ 37.016527] hnat_priv ppd = eth0.6 /etc/rc.d/S99boot_check: : INFO: rcS timing 35.516058305s seconds. Tue Aug 30 23:31:50 CST 2022 boot_check[5143]: Booting up finished. /etc/rc.d/S99cab_meshd: exist, exit. update cap mesh param done BusyBox v1.25.1 (2022-08-12 09:08:13 UTC) built-in shell (ash) ----------------------------------------------------- Welcome to XiaoQiang! ----------------------------------------------------- $$$$$$\ $$$$$$$\ $$$$$$$$\ $$\ $$\ $$$$$$\ $$\ $$\ $$ __$$\ $$ __$$\ $$ _____| $$ | $$ | $$ __$$\ $$ | $$ | $$ / $$ |$$ | $$ |$$ | $$ | $$ | $$ / $$ |$$ |$$ / $$$$$$$$ |$$$$$$$ |$$$$$\ $$ | $$ | $$ | $$ |$$$$$ / $$ __$$ |$$ __$$< $$ __| $$ | $$ | $$ | $$ |$$ $$< $$ | $$ |$$ | $$ |$$ | $$ | $$ | $$ | $$ |$$ |\$$\ $$ | $$ |$$ | $$ |$$$$$$$$\ $$$$$$$$$ | $$$$$$ |$$ | \$$\ \__| \__|\__| \__|\________| \_________/ \______/ \__| \__| root@XiaoQiang:/#


F0: 102B 0000 FA: 1040 0000 FA: 1040 0000 [0200] F9: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 2400 0041 [0000] G0: 1190 0000 EC: 0000 0000 [1000] T0: 0000 022F [010F] Jump to BL NOTICE: BL2: v2.6(release):82a3fbe10a-dirty NOTICE: BL2: Built : 16:56:29, Mar 29 2022 INFO: BL2: Doing platform setup NOTICE: WDT: disabled NOTICE: CPU: MT7986 (2000MHz) NOTICE: EMI: Using DDR4 settings before ctrl3 = 0x218000 clear request & ack after ctrl3 = 0x208000 DVFSRC_SUCCESS 0 dump drm registers data: 1001d000 | 00000000 00000000 00000000 00000000 1001d010 | 00000000 00000000 00000000 00000000 1001d020 | 00000000 00000000 00000000 00000000 1001d030 | 00a083f1 000000ff 00100000 00000000 1001d040 | 00027e71 000200a0 00020303 000000ff 1001d050 | 00000000 00000000 00000000 00000000 1001d060 | 00000002 00000000 00000000 00000000 drm: 500 = 0xc toprgu: 80 = 0x0 [DDR Reserve] ddr reserve mode not be enabled yet Save DRM_DEBUG_CTL(0xa083f1) DRM_LATCH_CTL : 0x27e71 DRM_LATCH_CTL2: 0x200a0 drm_update_reg: 1, bits: 0x8000, addr: 0x1001d030, val: 0xa083f1 drm_update_reg: 0, bits: 0x80000, addr: 0x1001d030, val: 0xa083f1 drm_update_reg: 0, bits: 0x200, addr: 0x1001d034, val: 0xff drm_update_reg: 0, bits: 0x200000, addr: 0x1001d034, val: 0xff drm_update_reg: 0, bits: 0x100, addr: 0x1001d034, val: 0xff MTK_DRM_DEBUG_CTL : 0xa083f1 MTK_DRM_DEBUG_CTL2: 0xff drm_update_reg: 0, bits: 0x4000, addr: 0x1001d030, val: 0xa083f1 DRM DDR reserve mode FAIL! a083f1 DDR RESERVE Success 0 drm_update_reg: 0, bits: 0x2000, addr: 0x1001d030, val: 0xa083f1 drm_update_reg: 0, bits: 0x1000, addr: 0x1001d030, val: 0xa083f1 [DRAM] into mt_set_emi [EMI] ComboMCP not ready, using default setting Init_DRAM:2139: init PCDDR4 dram Start [MD32_INIT] in c code >>>>>> [MD32_INIT] 3 [MD32_INIT] 4 [MD32_INIT] 5 [MD32_INIT] 6 [MD32_INIT] V22 add 1 [MD32_INIT] V22 add 1 end [MD32_INIT] 7 [MD32_INIT] 8 [MD32_INIT] 9 [MD32_INIT] 10 [MD32_INIT] 11 [MD32_INIT] 12 [MD32_INIT] 13 [MD32_INIT] 14 [MD32_INIT] 15 [MD32_INIT] 16 [MD32_INIT] 17 [MD32_INIT] 18 [MD32_INIT] 19 [MD32_INIT] 20 [MD32_INIT] 21 [MD32_INIT] 22 [MD32_INIT] 23 [MD32_INIT] 28 [MD32_INIT] 29 [MD32_INIT] 30 for RTMRW, if have [MD32_INIT] in c code <<<<<< [Set_DRAM_Pinmux_Sel] DRAMPinmux = 0 [Bian_co] ETT version 0.0.0.1 dram_type 4, R0 cbt_mode 0, R1 cbt_mode 0 VENDOR=136 Read voltage for 1600, 0 Vio18 = 0 Vcore = 0 Vdram = 0 Vddq = 0 Vmddr = 0 == DRAMC_CTX_T == support_channel_num: 1 channel: 0 support_rank_num: 1 rank: 0 freq_sel: 22 shu_type: 0 dram_type: 4 dram_fsp: 0 odt_onoff: 1 DBI_R_onoff: 0, 0 DBI_W_onoff: 0, 0 data_width: 16 test2_1: 0x55000000 test2_2: 0xaa000100 frequency: 1600 freqGroup: 1600 u1PLLMode: 0 dram type 6 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== OCD DRVP=0 ,CALOUT=0 OCD DRVP=1 ,CALOUT=0 OCD DRVP=2 ,CALOUT=0 OCD DRVP=3 ,CALOUT=0 OCD DRVP=4 ,CALOUT=0 OCD DRVP=5 ,CALOUT=0 OCD DRVP=6 ,CALOUT=0 OCD DRVP=7 ,CALOUT=0 OCD DRVP=8 ,CALOUT=0 OCD DRVP=9 ,CALOUT=1 OCD DRVP calibration OK! DRVP=9 OCD DRVN=0 ,CALOUT=1 OCD DRVN=1 ,CALOUT=1 OCD DRVN=2 ,CALOUT=1 OCD DRVN=3 ,CALOUT=1 OCD DRVN=4 ,CALOUT=1 OCD DRVN=5 ,CALOUT=1 OCD DRVN=6 ,CALOUT=0 OCD DRVN calibration OK! DRVN=6 [SwImpedanceCal] DRVP=9, DRVN=6 freq_region=0, Reg: DRVP=11, DRVN=8, ODTP=6 MEM_TYPE=6, freq_sel=22 [ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:=================================== PCDDR4 DRAM CONFIGURATION =================================== CWL = 0x7 RTT_NORM = 0x6 CL = 0xb AL = 0x0 BL = 0x0 RBT = 0x0 WR = 0x8 =================================== =================================== ANA top config =================================== ASYNC_MODE = 3 DLL_ASYNC_EN = 1 ALL_SLAVE_EN = 0 NEW_RANK_MODE = 0 DLL_IDLE_MODE = 1 LP45_APHY_COMB_EN = 1 TX_ODT_DIS = 0 NEW_8X_MODE = 0 =================================== =================================== data_rate = 3200 CKR = 1 DQ_P2S_RATIO = 8 =================================== CA_P2S_RATIO = 8 DQ_CA_OPEN = 0 DQ_SEMI_OPEN = 0 CA_SEMI_OPEN = 0 CA_FULL_RATE = 0 DQ_CKDIV4_EN = 0 CA_CKDIV4_EN = 0 CA_PREDIV_EN = 0 PH8_DLY = 31 SEMI_OPEN_CA_PICK_MCK_RATIO= 0 DQ_AAMCK_DIV = 4 CA_AAMCK_DIV = 4 CA_ADMCK_DIV = 4 DQ_TRACK_CA_EN = 0 CA_PICK = 1600 CA_MCKIO = 1600 MCKIO_SEMI = 0 PLL_FREQ = 3200 DQ_UI_PI_RATIO = 32 CA_UI_PI_RATIO = 0 =================================== =================================== memory_type:PCDDR4 GP_NUM : 1 SRAM_EN : 1 MD32_EN : 0 =================================== =========================================== HW_ZQCAL_config =========================================== ZQCALL is 0 TZQLAT is 27 ZQCSDUAL is 0 ZQCSCNT is 511 =========================================== [ANA_INIT] >>>>>>>>>>>>>> [ANA_ClockOff_Sequence] flow start WLY_DEBUG::ANA_ClockOff_Sequence delay 100ns start WLY_DEBUG::ANA_ClockOff_Sequence delay 100ns end [ANA_ClockOff_Sequence] flow end ============ PULL DRAM RESETB DOWN ============ ========== PULL DRAM RESETB DOWN end ========= ============ SUSPEND_ON ============ ============ SUSPEND_ON end ============ ============ SPM_control ============ ============ SPM_control end ============ <<<<<< [CONFIGURE PHASE]: ANA_TX >>>>>> [CONFIGURE PHASE][SHUFFLE]: PLL =================================== data_rate = 3200,PCW = 0X7800 =================================== <<<<<< [CONFIGURE PHASE][SHUFFLE]: PLL INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x0 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 >>>>>> [CONFIGURE PHASE][SHUFFLE]: ANA CLOCK DIV configuration INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B0_TEMP_VALUE= 0x0 PH8_DLY= 0x1f INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B1_TEMP_VALUE= 0x0 PH8_DLY= 0x1f INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 INFO: RG_ARDQ_REV_B2_TEMP_VALUE= 0x0 PH8_DLY= 0x1f INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 PH8_DLY= 0x1f <<<<<< [CONFIGURE PHASE][SHUFFLE]: ANA CLOCK DIV configuration >>>>>> [CONFIGURE PHASE][SHUFFLE]: DLL INFO: RG_ARCMD_REV_TEMP_VALUE= 0x60 INFO: RG_ARCMD_REV_TEMP_VALUE= 0x61 <<<<<< [CONFIGURE PHASE][SHUFFLE]: DLL [ANA_INIT] flow start [ANA_INIT] PLL >>>>>>>> [ANA_INIT] PLL <<<<<<<< [ANA_INIT] MIDPI >>>>>>>> [ANA_INIT] MIDPI <<<<<<<< [ANA_INIT] DLL >>>>>>>> [ANA_INIT] DLL <<<<<<<< [ANA_INIT] flow end [ANA_INIT] <<<<<<<<<<<<< [Flow] [DDRPHY] DIG_CONFIG_NONSHUF_DCM <<<<< [Flow] [DDRPHY] DIG_CONFIG_NONSHUF_DCM <<<<< [Flow] Enable top DCM control >>>>> [Flow] Enable top DCM control <<<<< Enable DLL master slave shuffle ============================================================== Gating Mode config ============================================================== Config description: RX_GATING_MODE 0: Pulse Mode 1: Burst Mode(8UI) 2: Burst Mode(7UI) 3: Original Burst Mode RX_GATING_TRACK_MODE 0: Valid DLY Mode 1: Valid Mode (Jade-like) 2: FIFO mode SELPH_MODE 0: By rank 1: By Phase ============================================================== GAT_TRACK_EN = 1 RX_GATING_MODE = 2 RX_GATING_TRACK_MODE = 2 SELPH_MODE = 1 PICG_EARLY_EN = 1 VALID_LAT_VALUE = 0 ============================================================== Enter into Gating configuration >>>> Exit from Gating configuration <<<< [DIG_HW_NONSHUF_ZQCAL_CFG],Configuration Enter [DIG_HW_NONSHUF_ZQCAL_CFG_FOR_PCDDR],Configuration Enter [DIG_HW_NONSHUF_ZQCAL_CFG],Configuration Enter [DIG_HW_NONSHUF_ZQCAL_CFG_FOR_PCDDR],Configuration Enter Enter into PICG configuration >>>> Exit from PICG configuration <<<< [DIG_SHUF_CONFIG] DCM_FUNCTION >>>>>>, group_id=0 [DIG_SHUF_CONFIG] DCM_FUNCTION <<<<<<, group_id=0 [DIG_FREQ_CONFIG][TX_CA][Delay] ch_id:0, group_id:0 >>>>> [DIG_FREQ_CONFIG][TX_CA][Delay] ch_id:0, group_id:0 <<<<< [DIG_HW_SHUF_ZQCAL_CFG] Group:0, Configuration Enter [ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:=================================== PCDDR4 DRAM CONFIGURATION =================================== CWL = 0x7 RTT_NORM = 0x6 CL = 0xb AL = 0x0 BL = 0x0 RBT = 0x0 WR = 0x8 =================================== [ReadLatency GET] MR_CL:[ReadLatency GET] MR_CL:UI_MCK_least is 1 RX_GW_selph_by_ps[0] is 12464 RX_GW_selph_by_ps[1] is 12464 RX_GW_selph_by_ps[2] is 12464 RX_GW_selph_by_ps[3] is 12464 =================================== RX_path CONFIGURATION =================================== data_rate is 3200 dq_p2s_ratio is 8 ca_default_delay is 1 ca_ser_latency is 7 cs2RL_start is 1 byte_num is 2 rank_num is 2 RL[0] is 24 RL[1] is 24 RL_min is 24 RL_max is 24 TDQSCK[0] is 0 TDQSCK[1] is 0 TDQSCK[2] is 0 TDQSCK[3] is 0 dqsien_default_delay is 0 dqsien_ser_latency is 7 oe_ser_latency is 4 gating_window_ahead_dqs is 2 aphy_slice_delay is 11 aphy_dtc_delay is 100 aphy_lead_lag_margin is 16 dram_ui_ratio is 2 dq_ui_unit is 312 ca_ui_unit is 312 MCK_unit is 2496 dramc_dram_ratio is 4 CKR is 1 tRPRE_toggle is 0 tRPRE_static is 2 tRPST is 0 DQSIENMODE is 1 BL is 16 FAKE_1TO16_MODE is 0 SVA_1_10_t2_SPEC is 11 read_cmd_out is 1 ca_MCKIO_ui_unit is 312 ca_p2s_ratio is 8 TDQSCK_min_SPEC is 0 TDQSCK_max_SPEC is 360 TX_pipeline is 1 RX_pipeline is 1 NEW_RANK_MODE is 0 close_loop_mode is 1 =================================== =================================== RX_path RG value =================================== RX_UI_P0[0] is 15 RX_UI_P0[1] is 15 RX_UI_P0[2] is 15 RX_UI_P0[3] is 15 RX_UI_P1[0] is 19 RX_UI_P1[1] is 19 RX_UI_P1[2] is 19 RX_UI_P1[3] is 19 RX_PI[0] is 31 RX_PI[1] is 31 RX_PI[2] is 31 RX_PI[3] is 31 DQSINCTL is 3 DATLAT_DSEL is 11 DATLAT is 12 DATLAT_DSEL_PHY is 12 DLE_EXTEND is 1 RX_IN_GATE_EN_HEAD is 0 RX_IN_GATE_EN_TAIL is 0 RX_IN_BUFF_EN_HEAD is 2 RX_IN_BUFF_EN_TAIL is 0 RX_IN_GATE_EN_PRE_OFFSET is 2 RANKINCTL_ROOT1 is 1 RANKINCTL is 1 RANKINCTL_STB is 2 RANKINCTL_RXDLY is 0 SHU_GW_THRD_POS is 42 SHU_GW_THRD_NEG is 0 RDSEL_TRACK_EN is 0 RDSEL_HWSAVE_MSK is 1 DMDATLAT_i is 12 RODTEN is 0 RODT is 0 RODTE is 1 RODTE2 is 1 ODTEN_MCK_P0[4] is 0 ODTEN_MCK_P1[4] is 0 ODTEN_UI_P0[4] is 0 ODTEN_UI_P1[4] is 0 RX_RANK_DQS_LAT is 0 RX_RANK_DQ_LAT is 1 RANKINCTL_PHY is 5 RANK_SEL_LAT_CA is 0 RANK_SEL_LAT_B0 is 0 RANK_SEL_LAT_B1 is 0 RANK_SEL_STB_EN is 0 RANK_SEL_RXDLY_TRACK is 0 RANK_SEL_STB_TRACK is 1 RANK_SEL_STB_PHASE_EN is 1 RANK_SEL_PHSINCTL is 2 RANK_SEL_STB_UI_MINUS is 2 RANK_SEL_STB_UI_PLUS is 0 RANK_SEL_MCK_P0 is 0 RANK_SEL_UI_P0 is 0 RANK_SEL_MCK_P1 is 1 RANK_SEL_UI_P1 is 0 R0DQSIENLLMTEN is 1 R0DQSIENLLMT is 96 R0DQSIENHLMTEN is 1 R0DQSIENHLMT is 63 R1DQSIENLLMTEN is 1 R1DQSIENLLMT is 96 R1DQSIENHLMTEN is 1 R1DQSIENHLMT is 63 DQSIEN_FIFO_DEPTH_HALF is 1 =================================== [ModeRegister CWL Config] data_rate:3200-MR_CWL:[ModeRegister CL Config] data_rate:3200-MR_CL:[ModeRegister WR Config] data_rate:3200-MR_WR:=================================== PCDDR4 DRAM CONFIGURATION =================================== CWL = 0x7 RTT_NORM = 0x6 CL = 0xb AL = 0x0 BL = 0x0 RBT = 0x0 WR = 0x8 =================================== [WriteLatency GET] MR_CWL:[WriteLatency GET] MR_CWL:===================================== print TX_path_config ===================================== data_ratio is 3200 dq_p2s_ratio is 8 cs2WL_start is 1 byte_num is 2 rank_num is 2 CKR is 1 DBI_WR is 0 dly_1T_by_FDIV2 is 0 WL[0] is 20 WL[1] is 20 TDQSS[0][0] is 156 TDQSS[0][1] is 156 TDQSS[1][0] is 156 TDQSS[1][1] is 156 TDQS2DQ[0][0] is 0 TDQS2DQ[0][1] is 0 TDQS2DQ[1][0] is 0 TDQS2DQ[1][1] is 0 ca_p2s_ratio is 8 ca_default_dly is 1 ca_default_pi is 0 ca_ser_latency is 7 dqs_ser_laterncy is 7 dqs_default_dly is 5 dqs_oe_default_dly is 2 dq_ser_laterncy is 7 MCK_unit is 2496 dq_ui_unit is 312 ca_unit is 312 ca_MCKIO_unit is 312 ca_frate is 0 TX_ECC is 0 TWPRE is 4 OE_pre_margin is 400 OE_pst_margin is 500 OE_downgrade is 1 aphy_slice_dly is 11 aphy_dtc_dly is 100 aphy_tx_dly is 16 DDRPHY_CLK_EN_COMB_TX_OPT is 1 NEW_RANK_MODE is 0 close_loop_mode is 1 TXP_WORKAROUND_OPT is 0 ui2pi_ratio is 32 XRTW2W_PI_mute_time is 7 fake_mode is 0 =========================================== TX_DQ_UI_OE_pre is 2 TX_DQS_UI_OE_pre is 1 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 data_ratio 3200, TX_dq_latency_ps is 8112, TX_dq_latency_MCK is 3 =========================================== print TX_path_attribution =========================================== TX_DQ_MCK_OE[0][0] is 2 TX_DQ_MCK_OE[0][1] is 2 TX_DQ_MCK_OE[1][0] is 2 TX_DQ_MCK_OE[1][1] is 2 TX_DQ_UI_OE[0][0] is 6 TX_DQ_UI_OE[0][1] is 6 TX_DQ_UI_OE[1][0] is 6 TX_DQ_UI_OE[1][1] is 6 TX_DQ_MCK[0][0] is 3 TX_DQ_MCK[0][1] is 3 TX_DQ_MCK[1][0] is 3 TX_DQ_MCK[1][1] is 3 TX_DQ_UI[0][0] is 2 TX_DQ_UI[0][1] is 2 TX_DQ_UI[1][0] is 2 TX_DQ_UI[1][1] is 2 TX_DQ_PI[0][0] is 0 TX_DQ_PI[0][1] is 0 TX_DQ_PI[1][0] is 0 TX_DQ_PI[1][1] is 0 TX_DQ_UIPI_all[0][0] is 0 TX_DQ_UIPI_all[0][1] is 0 TX_DQ_UIPI_all[1][0] is 0 TX_DQ_UIPI_all[1][1] is 0 TX_DQ_dlyline[0][0] is 0 TX_DQ_dlyline[0][1] is 0 TX_DQ_dlyline[1][0] is 0 TX_DQ_dlyline[1][1] is 0 TX_DQS_MCK_OE[0][0] is 2 TX_DQS_MCK_OE[0][1] is 2 TX_DQS_MCK_OE[1][0] is 2 TX_DQS_MCK_OE[1][1] is 2 TX_DQS_UI_OE[0][0] is 6 TX_DQS_UI_OE[0][1] is 6 TX_DQS_UI_OE[1][0] is 6 TX_DQS_UI_OE[1][1] is 6 TX_DQS_MCK[0][0] is 3 TX_DQS_MCK[0][1] is 3 TX_DQS_MCK[1][0] is 3 TX_DQS_MCK[1][1] is 3 TX_DQS_UI[0][0] is 1 TX_DQS_UI[0][1] is 1 TX_DQS_UI[1][0] is 1 TX_DQS_UI[1][1] is 1 DDRPHY_CLK_EN_COMB_TX_OPT is 1 TX_DQS_PI[0][0] is 16 TX_DQS_PI[0][1] is 16 TX_DQS_PI[1][0] is 16 TX_DQS_PI[1][1] is 16 DDRPHY_CLK_EN_COMB_TX_PICG_CNT is 2 DDRPHY_CLK_EN_COMB_TX_DQS_SEL_P0 is 3 DDRPHY_CLK_EN_COMB_TX_DQS_SEL_P1 is 4 DDRPHY_CLK_EN_COMB_TX_DQ_RK0_SEL_P0 is 3 DDRPHY_CLK_EN_COMB_TX_DQ_RK0_SEL_P1 is 4 DDRPHY_CLK_EN_COMB_TX_DQ_RK1_SEL_P0 is 3 DDRPHY_CLK_EN_COMB_TX_DQ_RK1_SEL_P1 is 4 DPHY_TX_DCM_EXTCNT is 0 TX_PI_UPD_MODE is 1 TX_PI_UPDCTL_B0 is 0 TX_PI_UPDCTL_B1 is 0 TX_RANKINCTL_ROOT is 0 TX_RANKINCTL is 1 TX_RANKINCTL_TXDLY is 2 DDRPHY_CLK_DYN_GATING_SEL is 5 DDRPHY_CLK_EN_OPT is 1 ARPI_CMD is 0 TDMY is 9 TXOEN_AUTOSET_DQ_OFFSET is 3 TXOEN_AUTOSET_DQS_OFFSET is 3 TXOEN_AUTOSET_EN is 1 TXPICG_AUTOSET_OPT is 0 TXPICG_AUTOSET_EN is 1 TXPICG_DQ_MCK_OFFSET_LAG is 0 TXPICG_DQS_MCK_OFFSET_LAG is 0 TXPICG_DQ_UI_OFFSET_LEAD is 0 TXPICG_DQ_UI_OFFSET_LAG is 1 TXPICG_DQS_UI_OFFSET_LEAD is 1 TXPICG_DQS_UI_OFFSET_LAG is 0 =========================================== set APHY_PI_CKCGH_CNT is 4 when not fake_mode, cur data_rate is 3200 [DIG_SHUF_CONFIG] MISC >>>>>, group_id=0 [DIG_SHUF_CONFIG] MISC <<<<<<, group_id=0 [DIG_SHUF_CONFIG] DBI >>>>>>, group_id=0 [DIG_SHUF_CONFIG] DBI <<<<<<, group_id=0 dramc_dram_ratio: 4 DDR4_DivMode: 1 freq_index: 1600 match AC timing 1 [DDR4_ac_timing_setting]start [PC4 WR preamble settings]>>>>>>>> group_id = 0. [PC4 WR preamble settings]<<<<<<<< group_id = 0. clk_dramc_ref_sel FREQ=16 fmem_ck_bfe_dcm_ch0 FREQ=253 fmem_ck_aft_dcm_ch0 FREQ=253 SetClkFreeRun enter => DRAM clock free run mode = ON. [DDR4] Pull Down reset. [DDR4] cke fix low 10ns at least. [DDR4] Delay 200 us. [DDR4] Pull Up reset. [DDR4] Delay 500 us. [DDR4] DRAM initilization RK:0 Enter >>>>>>>> [DDR4] Delay TXPR TRFC+10ns - 350ns(8Gb density)+10ns [DDR4_MRS] RK:0-MA:2-OP:0x[DDR4_MRS] RK:0-MA:3-OP:0x[DDR4_MRS] RK:0-MA:1-OP:0x[DDR4_MRS] RK:0-MA:4-OP:0x[DDR4_MRS] RK:0-MA:5-OP:0x[DDR4] DQ Vref calibration>>>>>>> [DDR4] DQ Vref Enable DQ vref calibration. [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] wait tVREFDQE-150ns [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] DQ Vref modify range and value [DDR4] DQ Vref Exit DQ vref calibration. [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4] wait tVREFDQx-150ns [DDR4] DQ Vref calibration<<<<<<< [DDR4_MRS] RK:0-MA:0-OP:0x[DDR4_ZQ] RK:0 Enter >>>>>>>> [DDR4_ZQ] RK:0 Exit <<<<<<<< [DDR4] Delay ZQinit - 718ns for 1333 at least max(512Mck,640ns) [DDR4] DRAM initilization RK:0 Exit <<<<<<< [DDR4] Enable refresh.....All bank refresh only SetClkFreeRun enter => DRAM clock free run mode = OFF. [DIG_HW_NONSHUF_ZQCAL_SWITCH],Configuration Enter [DIG_HW_NONSHUF_DQSG_SWITCH],Configuration Enter SET_CKE_2_RANK_INDEPENDENT_RUN_TIME: ON [MiockJmeterHQA] =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [DramcMiockJmeter] u1RxGatingPI = 0 0 : 2286, 2286 1 : 2271, 2271 2 : 2271, 2271 3 : 2272, 2272 4 : 2271, 2271 5 : 2267, 2267 6 : 2271, 2271 7 : 2271, 2271 8 : 2267, 2267 9 : 2272, 2272 10 : 2272, 2272 11 : 2272, 2272 12 : 2271, 2271 13 : 2276, 2276 14 : 2272, 2272 15 : 2271, 2271 16 : 2271, 2271 17 : 2272, 2272 18 : 2271, 2271 19 : 2272, 2272 20 : 2271, 2271 21 : 2271, 2271 22 : 2272, 2272 23 : 2271, 2271 24 : 2271, 2271 25 : 2271, 2271 26 : 2271, 2271 27 : 2272, 2272 28 : 2266, 2266 29 : 2271, 2271 30 : 2272, 2272 31 : 2271, 2271 32 : 2271, 2271 33 : 2276, 2276 34 : 2276, 2276 35 : 2276, 2276 36 : 2276, 2276 37 : 2276, 5 38 : 2271, 0 39 : 2276, 0 40 : 2271, 0 41 : 2271, 0 42 : 2272, 0 43 : 2271, 0 44 : 2272, 0 45 : 2272, 0 46 : 2272, 0 47 : 2271, 0 48 : 2272, 0 49 : 2271, 0 50 : 2276, 0 51 : 2271, 0 52 : 2271, 0 53 : 2272, 0 54 : 2272, 0 55 : 2271, 0 56 : 2266, 0 57 : 2272, 0 58 : 2276, 0 59 : 2271, 0 60 : 2272, 0 61 : 2267, 0 62 : 2276, 0 63 : 2272, 0 64 : 2272, 0 65 : 2276, 0 66 : 2272, 0 67 : 2271, 0 68 : 2266, 0 69 : 2276, 0 70 : 2271, 0 71 : 2272, 0 72 : 2271, 0 73 : 2272, 0 74 : 2271, 0 75 : 2272, 0 76 : 2272, 0 77 : 2272, 0 78 : 2276, 0 79 : 2272, 0 80 : 2271, 0 81 : 2277, 0 82 : 2267, 0 83 : 2271, 0 84 : 2271, 0 85 : 2272, 0 86 : 2271, 0 87 : 2266, 103 88 : 2272, 1964 89 : 2271, 2271 90 : 2272, 2272 91 : 2272, 2272 92 : 2271, 2271 93 : 2272, 2272 94 : 2271, 2271 95 : 2272, 2272 96 : 2272, 2272 97 : 2271, 2271 98 : 2272, 2272 99 : 2271, 2271 100 : 2276, 2276 101 : 2271, 2271 102 : 2271, 2271 103 : 2271, 2271 104 : 2276, 2276 105 : 2271, 2271 106 : 2272, 2272 107 : 2272, 2272 108 : 2271, 2271 109 : 2271, 2271 110 : 2271, 2271 111 : 2272, 2272 112 : 2272, 2272 113 : 2266, 2266 114 : 2266, 2266 115 : 2271, 2271 116 : 2272, 2272 117 : 2276, 2276 118 : 2271, 2271 119 : 2271, 2271 120 : 2271, 2271 121 : 2266, 2266 122 : 2271, 2271 123 : 2271, 2271 124 : 2276, 2276 125 : 2272, 2272 126 : 2272, 2272 127 : 2272, 2272 MIOCK jitter meter ch=0 1T = (88-37)*2 = 102 dly cells Clock freq = 1560 MHz, period = 641 ps, 1 dly cell = 628/100 ps ----->DramcWriteLeveling(PI) begin... =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== Begin: 0, End: 63, Step: 1, Bound: 64 [DDR4_MRS] RK:0-MA:2-OP:0x[DDR4_MRS] RK:0-MA:1-OP:0x[Write Leveling] delay byte0 byte1 byte2 byte3 0 O1( 1 1 1 O1( 1 1 2 O1( 1 1 3 O1( 1 1 4 O1( 1 1 5 O1( 1 1 6 O1( 1 1 7 O1( 1 1 8 O1( 1 1 9 O1( 1 1 10 O1( 1 1 11 O1( 1 0 12 O1( 1 0 13 O1( 1 0 14 O1( 1 0 15 O1( 0 0 16 O1( 0 0 17 O1( 0 0 18 O1( 0 0 19 O1( 0 0 20 O1( 0 0 21 O1( 0 0 22 O1( 0 0 23 O1( 0 0 24 O1( 0 0 25 O1( 0 0 26 O1( 0 0 27 O1( 0 0 28 O1( 0 0 29 O1( 0 0 30 O1( 0 0 31 O1( 0 0 32 O1( 0 0 33 O1( 0 0 34 O1( 0 0 35 O1( 0 0 36 O1( 0 0 37 O1( 0 0 38 O1( 0 0 39 O1( 0 0 40 O1( 0 0 41 O1( 1 1 42 O1( 0 1 43 O1( 1 1 44 O1( 1 1 45 O1( 1 1 46 O1( 1 1 47 O1( 1 1 48 O1( 1 1 49 O1( 1 1 Early breakpass bytecount = 0xff (0xff: all bytes pass) [DDR4_MRS] RK:0-MA:1-OP:0x[DDR4_MRS] RK:0-MA:2-OP:0xWrite leveling (Byte 0): 43 => 43 Write leveling (Byte 1): 41 => 41 DramcWriteLeveling(PI) end<----- =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [Gating] SW mode calibration [get_gating_start_pos] calculated gating ui = 15 12 0 | B1->B0 | 1212 1111 | 1 1 | (0 0) (0 0) 12 4 | B1->B0 | 1111 1111 | 1 1 | (0 0) (0 0) 12 8 | B1->B0 | 1111 1111 | 1 1 | (0 0) (0 0) 12 12 | B1->B0 | 1212 1111 | 1 1 | (0 1) (0 1) 12 16 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 12 20 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 12 24 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 12 28 | B1->B0 | 1212 1111 | 1 1 | (1 1) (1 1) 13 0 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 13 4 | B1->B0 | 1111 1111 | 1 1 | (1 1) (1 1) 13 8 | B1->B0 | 1515 1717 | 1 1 | (1 1) (1 1) 13 12 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 13 16 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 13 20 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 13 24 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 13 28 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 14 0 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 14 4 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 0) 14 8 | B1->B0 | 2222 2323 | 0 0 | (0 0) (0 1) 14 12 | B1->B0 | 2222 2323 | 0 0 | (0 1) (0 1) 14 16 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 14 20 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 14 24 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 14 28 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 0 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 4 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 8 | B1->B0 | 2222 2323 | 0 0 | (1 1) (1 1) 15 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 15 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 4 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 16 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 16 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (0 1) 16 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 16 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 8 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 12 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 16 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 20 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 24 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 17 28 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 0 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 4 | B1->B0 | 2323 2323 | 0 0 | (1 1) (1 1) 18 8 | B1->B0 | 2323 2323 | 0 0 | (1 0) (1 0) 18 12 | B1->B0 | 2323 2323 | 0 0 | (0 0) (1 0) 18 16 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 18 20 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 18 24 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 18 28 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 0 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 4 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) 19 8 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) best dqsien dly found for B0: (18, 10) 19 12 | B1->B0 | 2323 2323 | 0 0 | (0 0) (0 0) best dqsien dly found for B1: (18, 8) best DQS0 dly(UI, PI) = (18, 10) best DQS1 dly(UI, PI) = (18, 8) [Gating] SW calibration Done [DDR4_MRS] RK:0-MA:3-OP:0x=============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== Start DQ dly to find pass range UseTestEngine =0 UseTestEngine: 0 RX Vref Scan: 0 RX Vref 0 -> 0, step: 1 RX Delay -48 -> 63, step: 4 -48, [0] xxxxxxxx xxxxxxxx [MSB] -44, [0] xxxxxxxx xxxxxxxx [MSB] -40, [0] xxxxxxxx xxxxxxxx [MSB] -36, [0] xxxxxxxx xxxxxxxx [MSB] -32, [0] xxxxxxxx xxxxxxxx [MSB] -28, [0] xxxxxxxx xxxxxxxx [MSB] -24, [0] xxxxxxxx xxxxxxxx [MSB] -20, [0] xxxxxxxx xxxxxxxx [MSB] -16, [0] xxxxxxxx xxxxxxxx [MSB] -12, [0] xxxxxxxx xxxxxxxx [MSB] -8, [0] xxxxxxxx xxxxxxxx [MSB] -4, [0] xxxxxxox xxxxxxxx [MSB] 0, [0] xxoxxxox xxxxxxxx [MSB] 4, [0] oxoxoxoo oxoxoxox [MSB] 8, [0] oooooooo oooooooo [MSB] 12, [0] oooooooo oooooooo [MSB] 16, [0] oooooooo oooooooo [MSB] 20, [0] oooooooo oooooooo [MSB] 24, [0] oooooooo oooooooo [MSB] 28, [0] oooooooo oooooooo [MSB] 32, [0] oooooooo oooooooo [MSB] 36, [0] ooooooxo oooooooo [MSB] 40, [0] ooxoooxo oooooooo [MSB] 44, [0] xoxoxoxx xoxxxoxx [MSB] 48, [0] xxxxxxxx xxxxxxxx [MSB] RX Vref B0= 0, Window Sum 320, worse bit 0, min window 40 iDelay=48, Bit 0, Center 23 (4 ~ 43) 40 iDelay=48, Bit 1, Center 27 (8 ~ 47) 40 iDelay=48, Bit 2, Center 19 (0 ~ 39) 40 iDelay=48, Bit 3, Center 27 (8 ~ 47) 40 iDelay=48, Bit 4, Center 23 (4 ~ 43) 40 iDelay=48, Bit 5, Center 27 (8 ~ 47) 40 iDelay=48, Bit 6, Center 15 (-4 ~ 35) 40 iDelay=48, Bit 7, Center 23 (4 ~ 43) 40 RX Vref B1= 0, Window Sum 312, worse bit 11, min window 36 iDelay=48, Bit 8, Center 23 (4 ~ 43) 40 iDelay=48, Bit 9, Center 27 (8 ~ 47) 40 iDelay=48, Bit 10, Center 23 (4 ~ 43) 40 iDelay=48, Bit 11, Center 25 (8 ~ 43) 36 iDelay=48, Bit 12, Center 23 (4 ~ 43) 40 iDelay=48, Bit 13, Center 27 (8 ~ 47) 40 iDelay=48, Bit 14, Center 23 (4 ~ 43) 40 iDelay=48, Bit 15, Center 25 (8 ~ 43) 36 [DDR4_MRS] RK:0-MA:3-OP:0x=============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== DQS Delay: DQS0 = 0, DQS1 = 0 DQM Delay: DQM0 = 23, DQM1 = 24 DQ Delay: DQ0 =23, DQ1 =27, DQ2 =19, DQ3 =27 DQ4 =23, DQ5 =27, DQ6 =15, DQ7 =23 DQ8 =23, DQ9 =27, DQ10 =23, DQ11 =25 DQ12 =23, DQ13 =27, DQ14 =23, DQ15 =25 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [TxWindowPerbitCal] caltype:2 Autok:0 TX Vref Scan disable 809 |3 0 41|[0] xxxxxxxx xxxxxxxx [MSB] 811 |3 0 43|[0] xxoxxxox xxxxxxxo [MSB] 813 |3 0 45|[0] xxoxxxox xxoxoxxo [MSB] 815 |3 0 47|[0] xxoxxxox xxoxooxo [MSB] 817 |3 0 49|[0] oooxooox oooooooo [MSB] 833 |3 2 1|[0] xoxoooxo xoxxxooo [MSB] 835 |3 2 3|[0] xoxoxoxo xoxxxoxo [MSB] 837 |3 2 5|[0] xoxxxoxo xoxxxxxx [MSB] 839 |3 2 7|[0] xoxxxoxx xxxxxxxx [MSB] 841 |3 2 9|[0] xoxxxxxx xxxxxxxx [MSB] 843 |3 2 11|[0] xxxxxxxx xxxxxxxx [MSB] TX Bit0 (817~831) 16 824, Bit8 (817~831) 16 824, TX Bit1 (817~841) 26 829, Bit9 (817~837) 22 827, TX Bit2 (811~831) 22 821, Bit10 (813~831) 20 822, TX Bit3 (819~835) 18 827, Bit11 (817~831) 16 824, TX Bit4 (817~833) 18 825, Bit12 (813~831) 20 822, TX Bit5 (817~839) 24 828, Bit13 (815~835) 22 825, TX Bit6 (811~831) 22 821, Bit14 (817~833) 18 825, TX Bit7 (819~837) 20 828, Bit15 (811~835) 26 823, == TX Byte 0 == Update DQ dly =825 (3 ,0, 57) DQ OEN =(2 ,5) Update DQM dly =825 (3 ,0, 57) DQM OEN =(2 ,5) == TX Byte 1 == Update DQ dly =824 (3 ,0, 56) DQ OEN =(2 ,5) Update DQM dly =824 (3 ,0, 56) DQM OEN =(2 ,5) =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [TxWindowPerbitCal] caltype:0 Autok:0 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 3 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 5 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 7 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 9 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 11 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 13 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 15 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 17 TX Vref=3, minBit 8, minWin=14, winSum=277 TX Vref=5, minBit 0, minWin=16, winSum=293 TX Vref=7, minBit 0, minWin=16, winSum=296 TX Vref=9, minBit 0, minWin=16, winSum=301 TX Vref=11, minBit 0, minWin=17, winSum=315 TX Vref=13, minBit 0, minWin=17, winSum=325 TX Vref=15, minBit 0, minWin=17, winSum=328 TX Vref=17, minBit 0, minWin=19, winSum=338 [TxChooseVref] Worse bit 0, Min win 19, Win sum 338, Final Vref 17 [DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DDR4_MRS] RK:0-MA:6-OP:0x[DramcTXSetVref] TX Vref : CH0 Rank0, TX Range 1 Vref 17 Final TX Range 1 Vref 17 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== [TxWindowPerbitCal] caltype:0 Autok:0 TX Vref Scan disable 809 |3 0 41|[0] xxxxxxxx xxxxxxxx [MSB] 810 |3 0 42|[0] xxxxxxxx xxxxxxxx [MSB] 811 |3 0 43|[0] xxxxxxxx xxxxxxxx [MSB] 812 |3 0 44|[0] xxxxxxxx xxoxoxxo [MSB] 813 |3 0 45|[0] xxxxxxox xxoxooxo [MSB] 814 |3 0 46|[0] xxoxxxox oxoxoxoo [MSB] 815 |3 0 47|[0] xxoxxxox oxooooxo [MSB] 816 |3 0 48|[0] oxoxoxox oooooooo [MSB] 817 |3 0 49|[0] ooooooox oooooooo [MSB] 832 |3 2 0|[0] ooooooxo oooooooo [MSB] 833 |3 2 1|[0] ooooooxo oooooooo [MSB] 834 |3 2 2|[0] ooxoooxo xoxxxooo [MSB] 835 |3 2 3|[0] xoxoooxo xoxxxoxo [MSB] 836 |3 2 4|[0] xoxoxoxo xoxxxxxo [MSB] 837 |3 2 5|[0] xoxxxoxo xoxxxxxx [MSB] 838 |3 2 6|[0] xoxxxoxo xxxxxxxx [MSB] 839 |3 2 7|[0] xoxxxoxx xxxxxxxx [MSB] 840 |3 2 8|[0] xxxxxxxx xxxxxxxx [MSB] TX Bit0 (816~834) 19 825, Bit8 (814~833) 20 823, TX Bit1 (817~839) 23 828, Bit9 (816~837) 22 826, TX Bit2 (814~833) 20 823, Bit10 (812~833) 22 822, TX Bit3 (817~836) 20 826, Bit11 (815~833) 19 824, TX Bit4 (816~835) 20 825, Bit12 (812~833) 22 822, TX Bit5 (817~839) 23 828, Bit13 (815~835) 21 825, TX Bit6 (813~831) 19 822, Bit14 (816~834) 19 825, TX Bit7 (818~838) 21 828, Bit15 (812~836) 25 824, [TX_PER_BIT_DELAY_CELL] DelayCellTimex100 =628/100 ps == TX Byte 0 == u2DelayCellOfst[0]=4 cells (3 PI) u2DelayCellOfst[1]=9 cells (6 PI) u2DelayCellOfst[2]=1 cells (1 PI) u2DelayCellOfst[3]=6 cells (4 PI) u2DelayCellOfst[4]=4 cells (3 PI) u2DelayCellOfst[5]=9 cells (6 PI) u2DelayCellOfst[6]=0 cells (0 PI) u2DelayCellOfst[7]=9 cells (6 PI) Update DQ dly =822 (3 ,0, 54) DQ OEN =(2 ,5) Update DQM dly =825 (3 ,0, 57) DQM OEN =(2 ,5) == TX Byte 1 == u2DelayCellOfst[8]=1 cells (1 PI) u2DelayCellOfst[9]=6 cells (4 PI) u2DelayCellOfst[10]=0 cells (0 PI) u2DelayCellOfst[11]=3 cells (2 PI) u2DelayCellOfst[12]=0 cells (0 PI) u2DelayCellOfst[13]=4 cells (3 PI) u2DelayCellOfst[14]=4 cells (3 PI) u2DelayCellOfst[15]=3 cells (2 PI) Update DQ dly =822 (3 ,0, 54) DQ OEN =(2 ,5) Update DQM dly =824 (3 ,0, 56) DQM OEN =(2 ,5) =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== DATLAT Default: 0xc 0, 0x1, 0x2, 0x3, 0x4, 0x5, 0x6, 0x7, 0x8, 0x9, 0x10, 0x11, 0x12, 0x13, 0xbest_step = 11 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== Start DQ dly to find pass range UseTestEngine =1 UseTestEngine: 1 RX Vref Scan: 1 Set Vref Range= 9 -> 21 RX Vref 9 -> 21, step: 1 RX Delay -14 -> 63, step: 2 Set Vref, RX VrefLevel [Byte0]: 9 [Byte1]: 9 RX Vref B0= 9, Window Sum 238, worse bit 3, min window 28 RX Vref B1= 9, Window Sum 214, worse bit 10, min window 22 Set Vref, RX VrefLevel [Byte0]: 10 [Byte1]: 10 RX Vref B0= 10, Window Sum 250, worse bit 1, min window 30 RX Vref B1= 10, Window Sum 226, worse bit 10, min window 24 Set Vref, RX VrefLevel [Byte0]: 11 [Byte1]: 11 RX Vref B0= 11, Window Sum 258, worse bit 3, min window 30 RX Vref B1= 11, Window Sum 238, worse bit 10, min window 26 Set Vref, RX VrefLevel [Byte0]: 12 [Byte1]: 12 RX Vref B0= 12, Window Sum 262, worse bit 1, min window 32 RX Vref B1= 12, Window Sum 246, worse bit 10, min window 28 Set Vref, RX VrefLevel [Byte0]: 13 [Byte1]: 13 RX Vref B0= 13, Window Sum 276, worse bit 0, min window 34 RX Vref B1= 13, Window Sum 258, worse bit 10, min window 30 Set Vref, RX VrefLevel [Byte0]: 14 [Byte1]: 14 RX Vref B0= 14, Window Sum 282, worse bit 3, min window 34 RX Vref B1= 14, Window Sum 264, worse bit 10, min window 30 Set Vref, RX VrefLevel [Byte0]: 15 [Byte1]: 15 RX Vref B0= 15, Window Sum 288, worse bit 6, min window 34 RX Vref B1= 15, Window Sum 274, worse bit 10, min window 32 Set Vref, RX VrefLevel [Byte0]: 16 [Byte1]: 16 RX Vref B0= 16, Window Sum 292, worse bit 0, min window 36 RX Vref B1= 16, Window Sum 280, worse bit 10, min window 32 Set Vref, RX VrefLevel [Byte0]: 17 [Byte1]: 17 RX Vref B0= 17, Window Sum 298, worse bit 0, min window 36 RX Vref B1= 17, Window Sum 282, worse bit 10, min window 32 Set Vref, RX VrefLevel [Byte0]: 18 [Byte1]: 18 RX Vref B0= 18, Window Sum 304, worse bit 2, min window 36 RX Vref B1= 18, Window Sum 292, worse bit 10, min window 34 Set Vref, RX VrefLevel [Byte0]: 19 [Byte1]: 19 Set Vref, RX VrefLevel [Byte0]: 20 [Byte1]: 20 Set Vref, RX VrefLevel [Byte0]: 21 [Byte1]: 21 Final RX Vref Byte 0 = 18 to rank0 to rank1 Final RX Vref Byte 1 = 18 to rank0 to rank1 =============================================================================== Dram Type= 4, Freq= 1600, CH_0, rank 0 fsp= 0, odt_onoff= 1, Byte mode= 0, DivMode= 1 =============================================================================== DQS Delay: DQS0 = 0, DQS1 = 0 DQM Delay: DQM0 = 23, DQM1 = 25 DQ Delay: DQ0 =24, DQ1 =28, DQ2 =21, DQ3 =26 DQ4 =22, DQ5 =25, DQ6 =16, DQ7 =24 DQ8 =25, DQ9 =28, DQ10 =24, DQ11 =27 DQ12 =23, DQ13 =26, DQ14 =23, DQ15 =26 [DualRankRxdatlatCal] RK0: 11, RK1: 0, Final_Datlat 11 [Calibration Summary] Freqency 1600 CH 0, Rank 0 SW Impedance : PASS DUTY Scan : NO K ZQ Calibration : PASS Jitter Meter : NO K CBT Training : NO K Write leveling : PASS RX DQS gating : PASS RX DQ/DQS(RDDQC) : PASS TX DQ/DQS : PASS RX DATLAT : PASS RX DQ/DQS(Engine): PASS TX OE : NO K All Pass. TX_TRACKING: OFF [AUTO] write start address pass, BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] Detect DramSize: 0x8000000 [AUTO] BASE_ADDR : 0x8000000, OFFSET : 0x3 [AUTO] BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] Detect DramSize: 0x10000000 [AUTO] BASE_ADDR : 0x10000000, OFFSET : 0x3 [AUTO] BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] Detect DramSize: 0x20000000 [AUTO] BASE_ADDR : 0x20000000, OFFSET : 0x3 [AUTO] BASE_ADDR : 0x0, OFFSET : 0x3 [AUTO] TA2 read check fail, u4err_value = 65535, 3 [AUTO] Detect full size u4DramSize 0x20000000 NOTICE: EMI: Detected DRAM size: 512MB [MEM_TEST] 02: After DFS, before run time config [MEM_TEST] Rank 0 OK.(uiFixedAddr 0x40000000, Pass count = 16384, Fail count = 0) [TA2_TEST] === TA2 HW === OFFSET:0x200 TA2 PAT: 3 TA2 Trigger Write HW channel(0) Rank(0), TA2 pass, pass_cnt:1, err_cnt:0 [DramcRunTimeConfig]: ON PHYPLL DPM_CONTROL_AFTERK: ON PER_BANK_REFRESH: OFF REFRESH_OVERHEAD_REDUCTION: ON CMD_PICG_NEW_MODE: OFF TX_TRACKING: OFF RDSEL_TRACKING: OFF DQS Precalculation for DVFS: OFF RX_TRACKING: OFF DDR_HW_GATING DBG: ON DDR_ZQCS_ENABLE: ON RX_PICG_NEW_MODE: ON TX_PICG_NEW_MODE: ON ENABLE_RX_DCM_DPHY: ON LOWPOWER_GOLDEN_SETTINGS(DCM): ON DUMMY_READ_FOR_TRACKING: OFF !!! SPM_CONTROL_AFTERK: OFF !!! SPM could not control APHY IMPEDANCE_TRACKING: OFF HW_SAVE_FOR_SR: OFF CLK_FREE_FUN_FOR_DRAMC_PSEL: OFF PA_IMPROVEMENT_FOR_DRAMC_ACTIVE_POWER: OFF Read ODT Tracking: OFF Refresh Rate DeBounce: OFF DFS_NO_QUEUE_FLUSH: OFF DFS_NO_QUEUE_FLUSH_LATENCY_CNT: OFF ENABLE_DFS_RUNTIME_MRW: OFF DDR_RESERVE_NEW_MODE: ON ========================= [MEM_TEST] 03: After run time config [MEM_TEST] Rank 0 OK.(uiFixedAddr 0x40000000, Pass count = 16384, Fail count = 0) [TA2_TEST] === TA2 HW === OFFSET:0x200 TA2 Trigger Write HW channel(0) Rank(0), TA2 pass, pass_cnt:2, err_cnt:0 Init_DRAM:2480: init PCDDR4 dram End EMI: complex real chip dram calibration Verify pattern 1 (0x00~0xff)... EMI: mem8_base[0] = pattern8 = 0x0 Verify pattern 2 (0x00~0xffff)... EMI: mem16_base[0] = pattern16 = 0x0 Verify pattern 3 (0x00~0xffffffff)... EMI: mem32_base[0] = pattern32 = 0x0 NOTICE: EMI: complex R/W mem test passed drm_dram_reserved: MTK_DRM_MODE(22000000) NOTICE: SPI_NAND parses attributes from parameter page. NOTICE: SPI_NAND Detected ID 0x0 NOTICE: Page size 2048, Block size 131072, size 134217728 NOTICE: Initializing NMBM ... NOTICE: Signature found at block 1023 [0x07fe0000] NOTICE: First info table with writecount 0 found in block 960 NOTICE: Second info table with writecount 0 found in block 963 NOTICE: NMBM has been successfully attached in read-only mode INFO: BL2: Loading image id 3 INFO: Loading image id=3 at address 0x42000000 INFO: Image id=3 loaded: 0x42000000 - 0x42009061 INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0x42000000 INFO: Image id=5 loaded: 0x42000000 - 0x420ae288 NOTICE: BL2: Booting BL31 INFO: Entry point address = 0x43001000 INFO: SPSR = 0x3cd INFO: Total CPU count: 4 INFO: MCUSYS: Disable 512KB L2C shared SRAM INFO: check_ver = 0 INFO: Secondary bootloader is AArch64 INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: Maximum SPI INTID supported: 671 INFO: SPMC: Changed to SPMC mode NOTICE: BL31: v2.6(release):82a3fbe10a-dirty NOTICE: BL31: Built : 16:56:29, Mar 29 2022 INFO: [MPU](Region0)sa:0x0300, ea:0x0302 INFO: [MPU](Region0)apc0:0x80b6db69, apc1:0x00b6db6d INFO: [MPU](Region1)sa:0x0000, ea:0x0000 INFO: [MPU](Region1)apc0:0x00000000, apc1:0x00000000 INFO: [MPU](Region2)sa:0x0000, ea:0x0000 INFO: [MPU](Region2)apc0:0x00000000, apc1:0x00000000 INFO: [MPU](Region3)sa:0x0000, ea:0x0000 INFO: [MPU](Region3)apc0:0x00000000, apc1:0x00000000 INFO: [DEVAPC] devapc_init done INFO: BL31: Initializing runtime services INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x41e00000 INFO: SPSR = 0x3c9 In: serial@11002000 Out: serial@11002000 Err: serial@11002000 Net: eth0: ethernet@15100000 *** U-Boot Boot Menu *** 1. Startup system (Default) 2. Startup firmware0 3. Startup firmware1 4. Upgrade firmware 5. Upgrade ATF BL2 6. Upgrade ATF FIP 7. Upgrade single image 8. Load image 0. U-Boot console Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit detect button reset released! Reading from 0x0 to 0x5f7fdd8c, size 0x4 ... OK Boot failure detected on both systems Reading from 0x0 to 0x5f7fdd8c, size 0x4 ... OK Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK Writing to MTD device 'nmbm0'... OK OK Booting System 0 ubi0: attaching mtd9 ubi0: scanning is finished ubi0: attached mtd9 (name "ubi", size 110 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 ubi0: available PEBs: 2, total reserved PEBs: 878, PEBs reserved for bad PEB handling: 19 Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK ## Loading kernel from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-5.15.79 Type: Kernel Image Compression: lzma compressed Data Start: 0x460000e8 Data Size: 3928604 Bytes = 3.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x48000000 Entry Point: 0x48000000 Hash algo: crc32 Hash value: 77db497a Hash algo: sha1 Hash value: 474cb45f88e7db5de6f013a153b99eaaf22cf8ce Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt xiaomi_redmi-router-ax6000 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x463bf450 Data Size: 32768 Bytes = 32 KiB Architecture: AArch64 Hash algo: crc32 Hash value: afb34518 Hash algo: sha1 Hash value: 33475bc38fa9d8c3b69367220d36fd74a2cd5e21 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x463bf450 Uncompressing Kernel Image Loading Device Tree to 000000005f7ee000, end 000000005f7f8fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.15.79 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r21312-4c67d1e066) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Nov 17 01:55:55 2022 [ 0.000000] Machine model: Xiaomi Redmi Router AX6000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff] [ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff] [ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004fcfffff] [ 0.000000] node 0: [mem 0x000000004fd00000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 17 pages/cpu s30040 r8192 d31400 u69632 [ 0.000000] pcpu-alloc: s30040 r8192 d31400 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024 [ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 firmware=0 uart_en=1 [ 0.000000] Unknown kernel command line parameters "firmware=0 uart_en=1", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 500392K/524288K available (8320K kernel code, 898K rwdata, 2176K rodata, 384K init, 300K bss, 23896K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000126] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.000135] pid_max: default: 32768 minimum: 301 [ 0.000210] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.000218] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.001093] rcu: Hierarchical SRCU implementation. [ 0.001170] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.001351] smp: Bringing up secondary CPUs ... [ 0.001599] Detected VIPT I-cache on CPU1 [ 0.001621] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.001646] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.001906] Detected VIPT I-cache on CPU2 [ 0.001918] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000 [ 0.001929] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.002154] Detected VIPT I-cache on CPU3 [ 0.002164] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000 [ 0.002175] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.002201] smp: Brought up 1 node, 4 CPUs [ 0.002214] SMP: Total of 4 processors activated. [ 0.002217] CPU features: detected: 32-bit EL0 Support [ 0.002220] CPU features: detected: CRC32 instructions [ 0.002295] CPU: All CPU(s) started at EL2 [ 0.002306] alternatives: patching kernel code [ 0.004242] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.004263] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.004367] pinctrl core: initialized pinctrl subsystem [ 0.004941] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.005154] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.005174] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.005194] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.005421] thermal_sys: Registered thermal governor 'fair_share' [ 0.005424] thermal_sys: Registered thermal governor 'bang_bang' [ 0.005427] thermal_sys: Registered thermal governor 'step_wise' [ 0.005430] thermal_sys: Registered thermal governor 'user_space' [ 0.005604] ASID allocator initialised with 65536 entries [ 0.005850] pstore: Registered ramoops as persistent store backend [ 0.005854] ramoops: using 0x10000@0x42ff0000, ecc: 0 [ 0.012267] cryptd: max_cpu_qlen set to 1000 [ 0.013583] SCSI subsystem initialized [ 0.013656] libata version 3.00 loaded. [ 0.014437] clocksource: Switched to clocksource arch_sys_counter [ 0.014822] NET: Registered PF_INET protocol family [ 0.014895] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.015193] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.015206] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.015212] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.015233] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.015275] TCP: Hash tables configured (established 4096 bind 4096) [ 0.015323] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.015336] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.015412] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.015432] PCI: CLS 0 bytes, default 64 [ 0.017154] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 0.019193] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.019207] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.041322] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.043862] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.045479] printk: console [ttyS0] disabled [ 0.065646] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 121, base_baud = 2500000) is a ST16650V2 [ 0.716933] printk: console [ttyS0] enabled [ 0.721673] mtk_rng 1020f000.trng: registered RNG driver [ 0.721731] hwrng: no data available [ 0.727181] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.738516] loop: module loaded [ 0.741665] Loading iSCSI transport class v2.0-870. [ 0.747993] spi-nand spi0.0: ESMT SPI NAND was found. [ 0.753041] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.762394] Signature found at block 1023 [0x07fe0000] [ 0.767535] NMBM management region starts at block 960 [0x07800000] [ 0.778211] First info table with writecount 0 found in block 960 [ 0.797556] Second info table with writecount 0 found in block 963 [ 0.803720] NMBM has been successfully attached [ 0.808443] 8 fixed-partitions partitions found on MTD device spi0.0 [ 0.815019] Creating 8 MTD partitions on "spi0.0": [ 0.819794] 0x000000000000-0x000000100000 : "BL2" [ 0.825649] 0x000000100000-0x000000140000 : "Nvram" [ 0.830965] 0x000000140000-0x000000180000 : "Bdata" [ 0.836303] 0x000000180000-0x000000380000 : "Factory" [ 0.843230] 0x000000380000-0x000000580000 : "FIP" [ 0.849808] 0x000000580000-0x0000005c0000 : "crash" [ 0.855150] 0x0000005c0000-0x000000600000 : "crash_log" [ 0.860833] 0x000000600000-0x000007400000 : "ubi" [ 0.973061] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009600000, irq 126 [ 0.982574] i2c_dev: i2c /dev entries driver [ 0.987726] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 0.996034] NET: Registered PF_INET6 protocol family [ 1.001532] Segment Routing with IPv6 [ 1.005214] In-situ OAM (IOAM) with IPv6 [ 1.009148] NET: Registered PF_PACKET protocol family [ 1.014205] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.027183] 8021q: 802.1Q VLAN Support v1.8 [ 1.032138] pstore: Using crash dump compression: deflate [ 1.080941] mt7530 mdio-bus:1f: configuring for fixed/2500base-x link mode [ 1.088262] mt7530 mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 1.097860] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=134) [ 1.117707] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=135) [ 1.137254] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=136) [ 1.156806] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=137) [ 1.167600] DSA: tree 0 setup [ 1.171968] UBI: auto-attach mtd7 [ 1.175289] ubi0: default fastmap pool size: 40 [ 1.179802] ubi0: default fastmap WL pool size: 20 [ 1.184579] ubi0: attaching mtd7 [ 3.085127] ubi0: scanning is finished [ 3.113010] ubi0: attached mtd7 (name "ubi", size 110 MiB) [ 3.118500] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.125356] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.132123] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.139064] ubi0: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0 [ 3.145053] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 3.152252] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [ 3.160581] ubi0: available PEBs: 0, total reserved PEBs: 880, PEBs reserved for bad PEB handling: 19 [ 3.169782] ubi0: background thread "ubi_bgt0d" started, PID 450 [ 3.173607] block ubiblock0_1: created from ubi0:1(rootfs) [ 3.181244] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 3.205970] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 3.213224] Freeing unused kernel memory: 384K [ 3.294469] Run /sbin/init as init process [ 3.298548] with arguments: [ 3.301499] /sbin/init [ 3.304190] with environment: [ 3.307319] HOME=/ [ 3.309663] TERM=linux [ 3.312354] firmware=0 [ 3.315047] uart_en=1 [ 3.708523] init: Console is alive [ 3.712025] init: - watchdog - [ 3.994467] random: crng init done [ 4.466984] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.564661] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.582067] init: - preinit - [ 5.044790] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 5.053216] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.175811] UBIFS (ubi0:2): default file-system created [ 7.183186] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 7.188910] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 524 [ 7.398097] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 7.405919] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.415810] UBIFS (ubi0:2): FS size: 98152448 bytes (93 MiB, 773 LEBs), max 784 LEBs, journal size 4952064 bytes (4 MiB, 39 LEBs) [ 7.427435] UBIFS (ubi0:2): reserved for root: 4635982 bytes (4527 KiB) [ 7.434029] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID D7F77B4C-E05E-43D0-83D5-060DBE8BA542, small LPT model [ 7.449300] mount_root: overlay filesystem has not been fully initialized yet [ 7.456578] mount_root: switching to ubifs overlay [ 7.467427] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 7.478210] urandom-seed: Seed file not found (/etc/urandom.seed) [ 7.570066] procd: - early - [ 7.572987] procd: - watchdog - [ 8.146008] procd: - watchdog - [ 8.237538] procd: - ubus - [ 8.326938] procd: - init - Please press Enter to activate this console. [ 8.709398] urngd: v1.0.2 started. [ 8.724563] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.824129] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 8.838059] Loading modules backported from Linux version v5.15.74-0-ga3f2f5ac9d61 [ 8.845642] Backport generated by backports.git v5.15.74-1-0-ge2d78967 [ 9.196948] mt7986-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20220113162543a [ 9.196948] [ 9.513944] mt7986-wmac 18000000.wmac: WM Firmware Version: ____000000, Build Time: 20220113162641 [ 9.659522] mt7986-wmac 18000000.wmac: WA Firmware Version: DEV_000000, Build Time: 20220113163034 [ 13.556669] PPP generic driver version 2.4.2 [ 13.561564] NET: Registered PF_PPPOX protocol family [ 13.569069] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.761641] mtdblock: MTD device 'Bdata' is NAND, please consider using UBI block devices instead. [ 18.773029] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 18.784481] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 18.792906] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 18.793978] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 18.810891] br-lan: port 1(lan2) entered blocking state [ 18.816111] br-lan: port 1(lan2) entered disabled state [ 18.822742] device lan2 entered promiscuous mode [ 18.827431] device eth0 entered promiscuous mode [ 18.834158] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 18.846195] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 18.855850] br-lan: port 2(lan3) entered blocking state [ 18.857557] mt7530 mdio-bus:1f lan3: Link is Up - 100Mbps/Full - flow control rx/tx [ 18.861079] br-lan: port 2(lan3) entered disabled state [ 18.875675] device lan3 entered promiscuous mode [ 18.882373] br-lan: port 2(lan3) entered blocking state [ 18.887660] br-lan: port 2(lan3) entered forwarding state [ 18.893203] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 18.902519] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 18.911914] br-lan: port 3(lan4) entered blocking state [ 18.917177] br-lan: port 3(lan4) entered disabled state [ 18.924263] device lan4 entered promiscuous mode [ 18.934140] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 18.946530] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control off [ 18.953779] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready


OpenWrt now support stock layout or modified partition layout.

DC power barrel plug dimensions 4.0mm x 1.7mm.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/06/03 15:38
  • by runlevel5