Wistron CA8-4 a.k.a. Ovislink WLA-5000AP

Version/Model S/N Release Date OpenWrt Version Supported Model Specific Notes
- - Kamikaze 8.09.2 (tested) Setup
- - Attitude Adjustment 12.09 (tested) Setup

The latest out-of-the-box version that can be installed is 12.09 (howto below). Further versions up to 15.05 might run as well, but due to flash size limitations, those need to be manually built.

CPU Flash RAM Network USB Serial JTag
200 Mhz 4MB 32MB 1 x WLAN 11a/b/g No Yes Yes
Architecture MIPS
Vendors used this board layout Ovislink, Wistron, Airlink
Bootloader RedBoot
System-On-Chip Atheros AR2313A
CPU/Speed 200 MHz
Flash-Chip SPANSION S29JL032H
Flash size 4 MB
RAM 32 MB
RAM Chip Micron Chips (MT) 48LC8M32B2
Wireless Atheros AR5112A
Ethernet within SoC
Internet
USB None
Serial Yes
JTAG Yes

FIXME This hardware description differs from the one shown above. Please consolidate information in the above table, then delete this section (Board spec). --- tmomas 2015/09/30 13:32

Populated serial on JP1

VCC = +3.3V

[JTAG connector]

 VCC - []
       ()
  TX - ()
       ()
  RX - ()
 GND - ()
  • baud: 115200
  • 8 bit, 1 stop bit
  • No parity

Software

The AP ships with Linux 2.4.18-mips

      ============================================
        AR2313 Boot Loader Interface
        V1.03e00 2006-1-02 (zImage)
      ============================================
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash.
   4: Load calibration data then write to Flash via XModem.
3 seconds time out

ZImage -CRC = 0x1226dd06 Copying image from flash to SDRAM ... flash start= 0xbfc50000; flash end= 0xbfe85000 frequence_setup register_console min=0:CHIP:AR2313 CPU revision is: 0001800a Primary instruction cache 16kb, linesize 16 bytes (4 ways) Primary data cache 16kb, linesize 16 bytes (4 ways) Linux version 2.4.18-mips (root@localhost.localdomain) (gcc version 2.95.4 20010 319 (prerelease)) #2 €­ 4€ë 14 13:27:26 CST 2006 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Initial ramdisk at: 0x80343000 (1815109 bytes) On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: ip=192.168.1.3:192.168.1.1::netmask::eth0 calculating r4koff... 000dbba0(900000) Calibrating delay loop... 179.81 BogoMIPS Memory: 27044k/32768k available (1129k kernel code, 5724k reserved, 1912k data, 4k init, 0k highmem) Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes) Inode-cache hash table entries: 2048 (order: 2, 16384 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with no serial options enabled ttyS00 at 0xbc000000x (irq = 12) is a 16550A block: 64 slots per queue, batch=16 RAMDISK driver initialized: 16 RAM disks of 6500K size 1024 blocksize loop: loaded (max 8 devices) NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 2048) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 RAMDISK: Compressed image found at block 0 Freeing initrd memory: 1772k freed VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 4k freed Algorithmics/MIPS FPU Emulator v1.5 Bummer, can't write to log on /dev/tty5! console=/dev/ttyS0 init started: BusyBox v0.60.5 (2006.04.14-05:26+0000) multi-call binary Bummer, can't write to log on /dev/tty5! Starting pid 8, console /dev/ttyS0: '/etc/rc.d/rcS' Using /lib/modules/2.4.18-mips/eth.o CE8-1 Eth ver: 3.17e00.2005 Ethernet use flash address Ethernet For CA8-4 ae531x ethMAC(0)= 00:4f:69:50:ffffffa7:ffffffcf eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: duplex 0, link 1 full 3.19.00 macCtl= 0x1010000c macFlowCtl= 0x00000002 100 sb = 00 4F 69 50 A7 CF ether_setup ae531x ethMAC(1)= 00:4f:69:50:ffffffa7:ffffffce eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: Phy Status=ffff eth0: Phy Status=ffff eth1: duplex 0, link 1 full 3.19.00 macCtl= 0x1010000c macFlowCtl= 0x00000002 100 sb = 00 4F 69 50 A7 CE ether_setup Using /lib/modules/2.4.18-mips/wlan.o wlan: 0.7.1.1 BETA (Sam Leffler ) Using /lib/modules/2.4.18-mips/ath_hal.o Warning: loading ath_hal will taint the kernel: non-GPL license - Proprietary See http://www.tux.org/lkml/#export-tainted for information about tainted modu les ath_hal: 0.9.5.4 BETA (Sam Leffler ) Using /lib/modules/2.4.18-mips/ath_pci.o ath_pci: 0.8.3.2 BETA (Sam Leffler ) EEPROM version: 0x4008 ar5212EnableRadarDetection() ... ar5212EnableRadarDetection wlan0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wlan0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wlan0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wlan0: turbo rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wlan0: 802.11 address: 00:4f:69:50:a7:cd wlan0: Atheros 5212: irq=5 Using /lib/modules/2.4.18-mips/flashapi.o Bummer, can't write to log on /dev/tty5! Starting pid 19, console /dev/ttyS0: '/bin/sh' BusyBox v0.60.5 (2006.04.14-05:26+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. # syslogd: Execute for syslog/udp/514 maxvalidrate=10 11 Connect with ANY channel * set rd: 33594, cc: 826 Connect with ANY channel #


To use OpenWrt Kamikaze, you should change command line config in the default config file:

CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit"

Also change HAL target in the madwifi makefile to ap43

BUS:=PCI
ifneq ($(CONFIG_LINUX_2_6_ATHEROS),)
  BUS:=AHB
  HAL_TARGET:=ap43
endif

A RedBoot bootlader image has to be installed to support Kamikaze build. As of now this can be installed either via the WiliBox images, or via JTAG.

+Ethernet eth1: MAC address 80:70:00:fc:9f:c3
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.254, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
^C
RedBoot> fis init -f
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
RedBoot> load -r -v -b 0x80041000 openwrt-atheros-vmlinux.gz
|
Raw file loaded 0x80041000-0x80180fff, assumed entry at 0x80041000
RedBoot> fis create -r 0x80041000 -e 0x80041000 vmlinux.bin.gz

RedBoot> load -r -v -b 0x80041000 openwrt-atheros-root.squashfs        
/                                                                      
Raw file loaded 0x80041000-0x80220fff, assumed entry at 0x80041000     
RedBoot> fis list                                                      
Name              FLASH addr  Mem addr    Length      Entry point      
RedBoot           0xBE000000  0xBE000000  0x00050000  0x00000000       
RedBoot config    0xBE3DF000  0xBE3DF000  0x00001000  0x00000000       
FIS directory     0xBE3D0000  0xBE3D0000  0x0000F000  0x00000000       
vmlinux.bin.gz    0xBE050000  0x80041000  0x00140000  0x80041000       
RedBoot> fis create -b 0x80041000 -f 0xBE1A0000 -l 0x001E0000 -e 0x00000000 rootfs
+Ethernet eth1: MAC address 80:70:00:fc:9f:c3
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.254, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
^C
RedBoot> fis init -f
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
RedBoot> fis list
Name              FLASH addr  Mem addr    Length      Entry point
RedBoot           0xBE000000  0xBE000000  0x00050000  0x00000000
RedBoot config    0xBE3DF000  0xBE3DF000  0x00001000  0x00000000
FIS directory     0xBE3D0000  0xBE3D0000  0x0000F000  0x00000000
RedBoot> load -r -v -b 0x80041000 openwrt-atheros-vmlinux.gz
|
Raw file loaded 0x80041000-0x80130fff, assumed entry at 0x80041000
RedBoot> fis create -r 0x80041000 -e 0x80041000 vmlinux.bin.gz
RedBoot> load -r -v -b 0x80041000 openwrt-atheros-root.squashfs
|
Raw file loaded 0x80041000-0x80200fff, assumed entry at 0x80041000
RedBoot> fis create -b 0x80041000 -f 0xBE150000 -l 0x00280000 -e 0x00000000 rootfs
RedBoot> fis list
Name              FLASH addr  Mem addr    Length      Entry point
RedBoot           0xBE000000  0xBE000000  0x00050000  0x00000000
RedBoot config    0xBE3DF000  0xBE3DF000  0x00001000  0x00000000
FIS directory     0xBE3D0000  0xBE3D0000  0x0000F000  0x00000000
vmlinux.bin.gz    0xBE050000  0x80041000  0x000F0000  0x80041000
rootfs            0xBE150000  0xBE150000  0x00280000  0x00000000
RedBoot> fconfig
Run script at boot: true
Boot script:
.. fis load -b 0x80041000 -d vmlinux.bin.gz
.. go
Enter script, terminate with empty line
>> fis load -b 0x80041000 -d vmlinux.bin.gz
>> go
>>
Boot script timeout (1000ms resolution): 3
Use BOOTP for network configuration: false
Gateway IP address:
Local IP address: 192.168.1.1
Local IP address mask: 255.255.255.0
Default server IP address: 192.168.1.254
Console baud rate: 115200
DNS server IP address:
GDB connection port: 9000
Force console for special debug messages: false
Network hardware address [MAC]: 0x80:0x70:0x00:0xFC:0x9F:0xC3
Network debug at boot time: false
Update RedBoot non-volatile configuration - continue (y/n)? y
RedBoot> reset

Boot

+Ethernet eth1: MAC address 80:70:00:fc:9f:c3
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.254, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load -b 0x80041000 -d vmlinux.bin.gz
Image loaded from 0x80041000-0x80289085
RedBoot> go

Ethernet eth1: MAC address 00:11:22:33:44:55 IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.1.254, DNS server IP: 0.0.0.0 RedBoot(tm) bootstrap and debug environment [ROM] Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005 Copyright (C) 2000, 2001, 2002, Red Hat, Inc. RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each. == Executing boot script in 5.000 seconds - enter ^C to abort RedBoot> fis load -b 0x80041000 -d vmlinux.bin.gz Image loaded from 0x80041000-0x802fe65c RedBoot> go [ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc ve rsion 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 17:43 :48 UTC 2013 [ 0.000000] gpiochip_add: registered GPIOs 0 to 21 on device: ar5312-gpio [ 0.000000] ar5312-gpio: registered 22 GPIOs [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00018009 (MIPS 4Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 8128 [ 0.000000] Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs 2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 byt es [ 0.000000] Memory: 29164k/32768k available (2285k kernel code, 3604k reserve d, 353k data, 168k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.010000] Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632) [ 0.100000] pid_max: default: 32768 minimum: 301 [ 0.110000] Mount-cache hash table entries: 512 [ 0.120000] NET: Registered protocol family 16 [ 0.170000] bio: create slab <bio-0> at 0 [ 0.190000] Switching to clocksource MIPS [ 0.210000] NET: Registered protocol family 2 [ 0.260000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.350000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.430000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.510000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.580000] TCP reno registered [ 0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.690000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.770000] NET: Registered protocol family 1 [ 0.820000] Radio config found at offset 0x1000(0x100) [ 0.900000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.970000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY ) (c) 2001-2006 Red Hat, Inc. [ 1.090000] msgmni has been set to 56 [ 1.130000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54) [ 1.220000] io scheduler noop registered [ 1.270000] io scheduler deadline registered (default) [ 1.330000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 1.430000] serial8250: ttyS0 at MMIO 0xbc000003 (irq = 37) is a 16550A [ 1.530000] gpiodev: gpio device registered with major 253 [ 1.600000] physmap platform flash device: 00800000 at 1e000000 [ 1.670000] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufa cturer ID 0x000001 Chip ID 0x000a00 [ 1.800000] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.860000] Amd/Fujitsu Extended Query version 1.3. [ 1.920000] number of CFI chips: 1 [ 1.960000] Searching for RedBoot partition table in physmap-flash.0 at offse t 0x3d0000 [ 2.070000] 6 RedBoot partitions found on MTD device physmap-flash.0 [ 2.150000] Creating 6 MTD partitions on "physmap-flash.0": [ 2.220000] 0x000000000000-0x000000050000 : "RedBoot" [ 2.280000] 0x000000050000-0x000000190000 : "vmlinux.bin.gz" [ 2.360000] 0x0000001a0000-0x0000003d0000 : "rootfs" [ 2.420000] mtd: partition "rootfs" set to be root filesystem [ 2.490000] mtd: partition "rootfs_data" created automatically, ofs=350000, l en=80000 [ 2.590000] 0x000000350000-0x0000003d0000 : "rootfs_data" [ 2.660000] 0x0000003d0000-0x0000003df000 : "FIS directory" [ 2.730000] 0x0000003df000-0x0000003e0000 : "RedBoot config" [ 2.810000] 0x0000003e0000-0x000000400000 : "boardconfig" [ 2.950000] eth0: Atheros AR231x: 00:4f:69:50:17:af, irq 4 [ 3.090000] ar231x_eth_mii: probed [ 3.130000] eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01) [ 3.220000] TCP cubic registered [ 3.260000] NET: Registered protocol family 17 [ 3.310000] Bridge firewalling registered [ 3.360000] 8021q: 802.1Q VLAN Support v1.8 [ 3.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 3.510000] Freeing unused kernel memory: 168k freed [ 4.210000] eth0: Configuring MAC for full duplex - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - [ 10.720000] JFFS2 notice: (303) jffs2_build_xattr_subsystem: complete buildin g xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found. switching to jffs2 - init - Please press Enter to activate this console. [ 14.890000] Compat-drivers backp ort release: compat-drivers-2012-09-04-2-gddac993 [ 14.980000] Backport based on wireless-testing.git master-2012-09-07 [ 15.060000] compat.git: wireless-testing.git [ 15.170000] cfg80211: Calling CRDA to update world regulatory domain [ 15.240000] cfg80211: World regulatory domain updated: [ 15.300000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp) [ 15.400000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 15.500000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 20 00 mBm) [ 15.590000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20 00 mBm) [ 15.680000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 15.770000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 16.950000] ath5k: phy0: Atheros AR5312 chip found (MAC: 0x57, PHY: 0x42) [ 17.030000] ath5k: phy0: RF5112B multiband radio found (0x36) [ 17.110000] cfg80211: Calling CRDA for country: US [ 17.480000] cfg80211: Regulatory domain changed to country: US [ 17.550000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp) [ 17.650000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 27 00 mBm) [ 17.750000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 17 00 mBm) [ 17.840000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 17.930000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 18.020000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 18.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 30 00 mBm) [ 18.300000] PPP generic driver version 2.4.2 [ 18.800000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 19.170000] NET: Registered protocol family 24 [ 19.260000] nf_conntrack version 0.5.0 (458 buckets, 1832 max) BusyBox v1.19.4 (2013-03-14 17:30:13 UTC) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- ATTITUDE ADJUSTMENT (12.09, r36088) ----------------------------------------------------- * 1/4 oz Vodka Pour all ingredients into mixing * 1/4 oz Gin tin with ice, strain into glass. * 1/4 oz Amaretto * 1/4 oz Triple sec * 1/4 oz Peach schnapps * 1/4 oz Sour mix * 1 splash Cranberry juice ----------------------------------------------------- root@OpenWrt:/#


Linux version 2.6.26.8 (agb@arrakis) (gcc version 4.1.2) #4 Tue Dec 29 14:55:54 UTC 2009 CPU revision is: 00018009 (MIPS 4Kc) Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Entering add_active_range(0, 0, 8192) 0 entries of 256 used Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0 -> 8192 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 8192 On node 0 totalpages: 8192 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8128 pages, LIFO batch:0 Movable zone: 0 pages used for memmap Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/prei nit Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29792k/32768k available (1898k kernel code, 2976k reserved, 304k data, 1 24k init, 0k highmem) SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 219.54 BogoMIPS (lpj=1097728) Mount-cache hash table entries: 512 net_namespace: 644 bytes NET: Registered protocol family 16 Radio config found at offset 0x1000(0x100) Switched to high resolution mode on CPU 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 ar531x: Registering GPIODEV device squashfs: version 3.0 (2006/03/15) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 58 io scheduler noop registered io scheduler deadline registered (default) gpiodev: gpio device registered with major 254 gpiodev: gpio platform device registered with access mask FFFFFFFF Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0xbc000003 (irq = 37) is a 16550A eth0: Atheros AR231x: 00:4f:69:50:17:af, irq 4 ar2313_eth_mii: probed eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01) physmap platform flash device: 00800000 at 1e000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0 Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available Searching for RedBoot partition table in physmap-flash.0 at offset 0x3d0000 6 RedBoot partitions found on MTD device physmap-flash.0 Creating 6 MTD partitions on "physmap-flash.0": 0x00000000-0x00050000 : "RedBoot" 0x00050000-0x00150000 : "vmlinux.bin.gz" 0x00150000-0x003d0000 : "rootfs" mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=100000 0x002d0000-0x003d0000 : "rootfs_data" 0x003d0000-0x003df000 : "FIS directory" 0x003df000-0x003e0000 : "RedBoot config" 0x003e0000-0x00400000 : "boardconfig" TCP vegas registered eth0: Configuring MAC for full duplex NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 124k freed Please be patient, while OpenWrt loads ... Algorithmics/MIPS FPU Emulator v1.5 mini_fo: using base directory: / mini_fo: using storage directory: /jffs device eth0 entered promiscuous mode br-lan: port 1(eth0) entering learning state br-lan: topology change detected, propagating br-lan: port 1(eth0) entering forwarding state PPP generic driver version 2.4.2 ip_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack version 0.5.0 (1024 buckets, 4096 max) ath_hal: module license 'Proprietary' taints kernel. ath_hal: 2009-05-08 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC , TX_DESC_SWAP, XR) ath_ahb: trunk wlan: trunk wlan: mac acl policy registered ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk) ath_rate_minstrel: look around rate set to 10% ath_rate_minstrel: EWMA rolloff level set to 75% ath_rate_minstrel: max segment size in the mrr set to 6000 us Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36 Mbps 48Mbps 54Mbps wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP ath_ahb: wifi0: Atheros 5312 WiSoC: mem=0xb8500000, irq=5


Manufacturer:

Access points:

GPL sources:

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/01/30 10:59
  • by danitool