Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:wifire:s1500_nbn [2023/07/02 13:00] – [OpenWrt installation] csharper2005toh:wifire:s1500_nbn [2023/10/16 19:48] – [Installation] csharper2005
Line 2: Line 2:
 /* This template is intended to be used via https://openwrt.org/meta/create_new_device_page . */ /* This template is intended to be used via https://openwrt.org/meta/create_new_device_page . */
  
-{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} 
  
 OEM/ODM name: Sercomm S1500 BUC OEM/ODM name: Sercomm S1500 BUC
Line 55: Line 54:
  
 /* stable release */ /* stable release */
-/* uncomment once stable release is available 
 ---- datatable ---- ---- datatable ----
 cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
Line 63: Line 61:
 filter  : Model=S1500.NBN filter  : Model=S1500.NBN
 ---- ----
-*/ 
  
- 
-/* snapshot */ 
-/* delete once stable release is available */ 
----- datatable ---- 
-cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt snapshot Install URL_url, Firmware OpenWrt snapshot Upgrade URL_url, Firmware OEM Stock URL_url 
-headers : Model, Version, Current Release, Firmware OpenWrt snapshot Install, Firmware OpenWrt snapshot Upgrade, Firmware OEM Stock 
-align   : c,c,c 
-filter  : Brand=WiFire 
-filter  : Model=S1500.NBN 
----- 
- 
- 
-{{page>meta:infobox:attention_trunk&noheader&nofooter&noeditbtn}} 
  
 -> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]] -> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
Line 93: Line 77:
 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
 <code bash> <code bash>
-printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock4+printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
 </code> </code>
  
Line 177: Line 161:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-^ Architecture     | RAMIPS                             | + 
-^ Vendor           | Sercomm                            | +---- datatemplatelist dttpllist ---- 
-^ Bootloader       | U-Boot SerComm/[[wp>MediaTek]]            | +template: meta:template_datatemplatelist 
-^ System-On-Chip   | MediaTek MT7621AT                  | +cols    : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHzFlash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHzWLAN 5.0GHzWLAN HardwaresWLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ 
-CPU/Speed        | 880 MHz                            | +filter  : Brand=WiFire 
-Flash-Chip       | NAND (ESMT F59L1G81MA)             | +filter  : Model=S1500.NBN 
-^ Flash size       | 128 MiB                            | +----
-RAM              | 128 MiB (Nanya NT5CC64M16GP)       | +
-^ Wireless / 2.4 GHz  | MT7602EN, b/g/nMIMO 2x2       | +
-^ Wireless / GHz | MT7612ENa/n/acMIMO 2x2         | +
-^ Ethernet         | 10/100/1000 Mbit/s w/ vlan support | +
-^ Switch           | MediaTek MT7530 (via SoC MT7621AT) | +
-^ Buttons          | 2 button (RESETWPS)              | +
-USB              | 1x 2.0                             | +
-^ UART           | [[#Serial|Yes]] (Not soldered on the board) | +
-^ mPCIe            | via J2 on PCB (Not soldered on the board) | +
-^ JTAG             | [[#JTAG|Yes]] via J3 on PCB (Not soldered on the board) |+
  
 ---- datatemplatelist dttpllist ---- ---- datatemplatelist dttpllist ----
Line 309: Line 283:
 **You will need:** **You will need:**
   * PC or Virtual machine with Linux   * PC or Virtual machine with Linux
-  * mtd partitions backup (**mtd1.bin** - //u-boot bootloader//, **mtd2.bin** - //Factory//)+  * mtd partitions backup (**uboot.bin** - //u-boot bootloader//, **factory.bin** - //Factory//)
   * http server with mtd partitions backup (i.e. with IP 192.168.1.2)   * http server with mtd partitions backup (i.e. with IP 192.168.1.2)
   * recovery image (see [[:toh:wifire:s1500_nbn#sercomm-recovery_utility]])    * recovery image (see [[:toh:wifire:s1500_nbn#sercomm-recovery_utility]]) 
Line 322: Line 296:
 2. Download //Factory// backup from your http server and write it: 2. Download //Factory// backup from your http server and write it:
 <code bash> <code bash>
-wget http://192.168.1.2/mtd2.bin+wget http://192.168.1.2/factory.bin
 </code> </code>
 <code bash> <code bash>
Line 336: Line 310:
  
 <code bash> <code bash>
-wget http://192.168.1.2/mtd1.bin+wget http://192.168.1.2/uboot.bin
 </code> </code>
 <code bash> <code bash>
  • Last modified: 2024/09/05 19:03
  • by csharper2005