Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
inbox:toh:wifire:s1500_nbn [2022/04/26 11:46] – [Info] demiurge67toh:wifire:s1500_nbn [2024/09/05 19:03] (current) – [sercomm-recovery utility] csharper2005
Line 1: Line 1:
 ====== WiFire S1500 NBN ====== ====== WiFire S1500 NBN ======
-~~NOTOC~~ 
- 
 /* This template is intended to be used via https://openwrt.org/meta/create_new_device_page . */ /* This template is intended to be used via https://openwrt.org/meta/create_new_device_page . */
  
-{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} 
  
-//Write a short, relevant description of the deviceInclude technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.//+OEM/ODM name: Sercomm S1500 BUC 
 +The WiFire S1500.NBN is CPE wireless router based on the MT7621 platform
  
-This devices is manufactured by OEM/ODM SerComm Corporation +/* //Write a short, relevant description of the deviceInclude a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.// */
-The production common name is Sercomm S1500+
  
 /*****/ /*****/
Line 15: Line 12:
 /*****/ /*****/
  
-{{ media:example:genericrouter1.png?200|Generic Router}}+{{media:wifire:e514.png?400|WiFire S1500.NBN}}
  
  
-===== OpenWrt support =====+===== Supported Versions =====
  
-<color red>**Not supported.**</color>+<!-- ToH: { 
 +  "source": "json", 
 +  "dom": "t", 
 +  "paging": false, 
 +  "rotate": true, 
 +  "shownColumns": ["brand", "model", "version", "supportedcurrentrel", "oemdevicehomepageurl", "forumsearch", "deviceid"], 
 +  "filterColumns": {"brand": "^WiFire$", "model": "^S1500\\.NBN$"
 +} -->
  
  
-/*** if info available: uncomment and fill in 
-===== Supporting activities ===== 
-//Describe if there are any ongoing activities that might lead to OpenWrt support.// 
- 
-  * OpenWrt forum thread: (add link) 
-***/ 
- 
- 
-/*** if info available: uncomment and fill in 
 ===== Experimental firmware ===== ===== Experimental firmware =====
  
-//List experimental firmware download links here.//+  * Community builds - https://forum.openwrt.org/t/add-support-for-beeline-smartbox-giga/99390/4
  
-//None at this time.// 
  
-  * External image (add link) 
-  * trunk image (add link) 
-  * ... 
-***/ 
- 
- 
-===== Hardware highlights ===== 
-^ CPU                        ^ Ram      ^ Flash   ^ Network     ^ WLAN   ^ USB      ^ Serial   ^ JTag   ^ 
-| MediaTek MT7621AT (880 MHz, 2 cores)    128 MiB  |  128 MiB  |  4x 10/100/1000  |  acbgn    1x 2.0  |   Yes    |   Yes    | 
  
 +===== Hardware Highlights =====
 +<!-- ToH: {
 +  "source": "json",
 +  "dom": "t",
 +  "paging": false,
 +  "rotate": true,
 +  "shownColumns": ["model", "version", "cpu", "cpumhz", "cpucores", "flashmb", "rammb", "wlanhardware", "wlan24ghz", "wlan50ghz", "ethernet100mports", "ethernet1gports", "modem", "usbports"],
 +  "filterColumns": {"brand": "^WiFire$", "model": "^S1500\\.NBN$"}
 +} -->
  
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
Line 58: Line 52:
 ***/ ***/
  
 +===== Installation =====
 +
 +
 +/* stable release */
 +<!-- ToH: {
 +  "source": "json",
 +  "dom": "t",
 +  "paging": false,
 +  "rotate": true,
 +  "shownColumns": ["model", "version", "supportedcurrentrel", "firmwareopenwrtinstallurl", "firmwareopenwrtupgradeurl", "firmwareoemstockurl"],
 +  "filterColumns": {"brand": "^WiFire$", "model": "^S1500\\.NBN$"}
 +} -->
 +
 +
 +-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
 +
 +===== OpenWrt installation =====
 +
 +  - Remove all dots from the factory image filename (except the dot before file extension)
 +  - Upload and update the firmware via the original web interface
 +  - Two options are possible after the reboot:
 +    * OpenWrt - that's OK, the mission accomplished
 +    * Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image.
 +
 +
 +===== Return to Stock =====
 +1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
 +<code bash>
 +printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
 +</code>
 +
 +2. Optional: Update with any version of stock firmware if you want to overwrite OpenWrt in Slot 0 completely.
  
-/*** if info available: uncomment and fill in 
 ===== Debricking ===== ===== Debricking =====
 -> [[docs:guide-user:troubleshooting:generic.debrick]] -> [[docs:guide-user:troubleshooting:generic.debrick]]
-***/+ 
 +==== sercomm-recovery utility ==== 
 +1. Compile [[https://github.com/danitool/sercomm-recovery|sercomm-recovery]] under the Linux: 
 +<code bash> 
 +git clone https://github.com/danitool/sercomm-recovery.git 
 +make 
 +</code> 
 + 
 +2. Connect the router with a cable and run sercomm-recovery: 
 +<code bash> 
 +sudo ./sercomm-recovery enp0s3 recovery_wifire-s1500.nbn_1st-v2.0.12_2nd-v2.0.14.bin 
 +</code> 
 +where: 
 +  //enp0s3// - network interface connected the router 
 +  //ifconfig// - list on available network interfaces 
 +  * //recovery_wifire-s1500.nbn_1st-v2.0.12_2nd-v2.0.14.bin// - recovery image with the //Sercomm1// bootflag activated 
 +  
 +3. Wait until the router is flashed and rebooted. 
 + 
 +[[https://mega.nz/folder/ks4R2S4D#g1l_wH-nBOMONrDqOkeEvQ|Download ready recovery images]] for Sercomm devices. 
 + 
 +It's also possible to create a recovery image containing OpenWrt.  
 + 
 +=== How to make own recovery images === 
 + 
 +You can use mtd0 ("ALL") backup as a recovery image. 
  
  
Line 114: Line 164:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-^ Architecture     | RAMIPS                             | 
-^ Vendor           | Sercomm                            | 
-^ Bootloader       | U-Boot SerComm/[[wp>MediaTek]]            | 
-^ System-On-Chip   | MediaTek MT7621AT                  | 
-^ CPU/Speed        | 880 MHz                            | 
-^ Flash-Chip       | NAND (ESMT F59L1G81MA)             | 
-^ Flash size       | 128 MiB                            | 
-^ RAM              | 128 MiB (Nanya NT5CC64M16GP)       | 
-^ Wireless / 2.4 GHz  | MT7602EN, b/g/n, MIMO 2x2       | 
-^ Wireless / 5 GHz | MT7612EN, a/n/ac, MIMO 2x2         | 
-^ Ethernet         | 10/100/1000 Mbit/s w/ vlan support | 
-^ Switch           | MediaTek MT7530 (via SoC MT7621AT) | 
-^ Buttons          | 2 button (RESET, WPS)              | 
-^ USB              | 1x 2.0                             | 
-^ Serial           | [[#Serial|Yes]] (Not soldered on the board) | 
-^ mPCIe            | via J2 on PCB (Not soldered on the board) | 
-^ JTAG             | [[#JTAG|Yes]] (Not soldered on the board) | 
  
 +<!-- ToH: {
 +  "source": "json",
 +  "dom": "t",
 +  "paging": false,
 +  "rotate": true,
 +  "shownColumns": ["brand", "model", "version", "devicetype", "availability", "supportedsincecommit", "supportedsincerel", "supportedcurrentrel", "unsupported_functions", "bootloader", "cpu", "target", "cpumhz", "flashmb", "rammb", "switch", "ethernet100mports", "ethernet1gports", "commentsnetworkports", "modem", "vlan", "wlan24ghz", "wlan50ghz", "wlanhardware", "wlancomments", "detachableantennas", "usbports", "sataports", "commentsusbsataports", "serial", "jtag", "ledcount", "buttoncount", "powersupply", "deviceid", "owrt_forum_topic_url", "wikideviurl", "oemdevicehomepageurl", "firmwareoemstockurl", "firmwareopenwrtinstallurl", "firmwareopenwrtupgradeurl", "comments"],
 +  "filterColumns": {"brand": "^WiFire$", "model": "^S1500\\.NBN$"}
 +} -->
 +
 +<!-- ToH: {
 +  "source": "json",
 +  "dom": "t",
 +  "paging": false,
 +  "rotate": true,
 +  "shownColumns": ["brand", "model", "version", "devicetype", "availability", "supportedsincecommit", "supportedsincerel", "supportedcurrentrel", "unsupported_functions", "bootloader", "cpu", "target", "cpumhz", "flashmb", "rammb", "switch", "ethernet100mports", "ethernet1gports", "commentsnetworkports", "modem", "vlan", "wlan24ghz", "wlan50ghz", "wlanhardware", "wlancomments", "detachableantennas", "usbports", "sataports", "commentsusbsataports", "serial", "jtag", "ledcount", "buttoncount", "powersupply", "deviceid", "owrt_forum_topic_url", "wikideviurl", "oemdevicehomepageurl", "firmwareoemstockurl", "firmwareopenwrtinstallurl", "firmwareopenwrtupgradeurl", "comments"],
 +  "filterColumns": {"brand": "^WiFire$", "model": "^S1500 NBN$"}
 +} -->
  
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
Line 148: Line 198:
 /* e.g. {{:media:yourbrand:yourbrand_yourmodel_front.jpg?400|}}                                  */ /* e.g. {{:media:yourbrand:yourbrand_yourmodel_front.jpg?400|}}                                  */
 /* Thanks, your wiki administration - Oct. 2015 */ /* Thanks, your wiki administration - Oct. 2015 */
 +=== Exterier Photo ===
 +{{ :media:wifire:wifire_s1500_front.jpg?400 |}} 
 +{{ :media:wifire:wifire_s1500_back.jpg?400 |}}
  
-**Insert photo of front of the casing** 
  
-**Insert photo of back of the casing**+=== Back Lable ===  
  
-**Insert photo of backside label**+{{ :media:wifire:wifire_s1500_shield.jpg?400 |}}
  
-**Insert photo of PCB**+=== Photo of PCB ===
  
 +{{ :media:wifire:wifire_s1500_pcb_up.jpeg?400 |}}
 +{{ :media:wifire:wifire_s1500_pcb_down.jpeg?400 |}}
 ==== Opening the case ==== ==== Opening the case ====
  
Line 163: Line 217:
 </WRAP> </WRAP>
  
-==== Serial ==== +==== UART ====
--> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.+
  
-How to connect to the Serial Port of this specific device:\\ +^ Serial connection parameters | 57600, 8N1, 3.3V |
-**Insert photo of PCB with markings for serial port** +
- +
-<WRAP BOX> +
-FIXME //Replace EXAMPLE by real values.// +
-</WRAP> +
- +
-^ Serial connection parameters\\ for WiFire S1500 NBN v4 | 57600, 8N1, 3.3V |+
  
 **[J4] on PCB:** **[J4] on PCB:**
Line 181: Line 227:
 ^4.| RX |  ^4.| RX | 
  
 +{{:media:wifire:uart1.jpeg?nolink&400|}}
  
 ==== JTAG ==== ==== JTAG ====
--> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc. 
  
 How to connect to the JTAG Port of this specific device:\\ How to connect to the JTAG Port of this specific device:\\
-**Insert photo of PCB with markings for JTAG port**+ 
 +{{:media:wifire:jtag.jpg?nolink&400|}}
 =====  Stock firmware ===== =====  Stock firmware =====
  
Line 193: Line 239:
     v. 2.0.14 - (build @ 2017-03-17, 13:15:30) - No link     v. 2.0.14 - (build @ 2017-03-17, 13:15:30) - No link
          
 +
 +=== Memory ===
 +
 +^mtd ^Partion ^Start ^End ^Байт ^Hex ^KiB ^MiB^
 +|1 |Uboot |0 |100 000 |1 048 576 |100 000 |1 024 |1|
 +|2 |Factory |100 000 |200 000 |1 048 576 |100 000 |1 024 |1|
 +|3 |Sys_Data |200 000 |1 600 000 |20 971 520 |1 400 000 |20 480 |20|
 +|4 |Boot_Flag |1 600 000 |1 700 000 |1 048 576 |100 000 |1 024 |1|
 +|5 |Kernel_1 |1 700 000 |1B00 000 |4 194 304 |400 000 |4 096 |4|
 +|6 |Kernel_2 |1b00 000 |1F00 000 |4 194 304 |400 000 |4 096 |4|
 +|7 |RootFS_1 |1F00 000 |4D00 000 |48 234 496 |2E00 000 |47 104 |46|
 +|8 |RootFS_2 |4D00 000 |7B00 000 |48 234 496 |2E00 000 |47 104 |46|
 +|9 |Ftool |7B00 000 |7C00 000 |1 048 576 |100 000 |1 024 |1|
 +|10 |BCT |7C00 000 |7F80 000 |3 670 016 |380 000 |3 584 |3,5|
 +|-|Reserved |7F80 000 |8 000 000 |524 288 |80 000 |512 |0,5|
 +|0 |All |0 |7F80 000 |133 693 440 |7F80 000 |130 560 |127,5|
 +
 === Layout factory-data === === Layout factory-data ===
  
Line 214: Line 277:
 ^5g |*:10 |LAN +2| ^5g |*:10 |LAN +2|
  
 +
 +
 +===== Bootloader mods =====
 +
 +==== Restoring the original U-boot bootloader and stock firmware  ====
 +
 +{{page>meta:infobox:dangerous&noheader&nofooter&noeditbtn}}
 +
 +**Input conditions:** 
 +  * router with Breed bootloader installed
 +
 +**You will need:**
 +  * PC or Virtual machine with Linux
 +  * mtd partitions backup (**uboot.bin** - //u-boot bootloader//, **factory.bin** - //Factory//)
 +  * http server with mtd partitions backup (i.e. with IP 192.168.1.2)
 +  * recovery image (see [[:toh:wifire:s1500_nbn#sercomm-recovery_utility]]) 
 +
 +
 +=== U-Boot and stock firmware recovery steps ===
 +
 +**<color #ed1c24>After executing each command, carefully read its output before executing the next one.</color>**
 +
 +1. Enter the Breed telnet shell (IP: 192.168.1.1)
 +
 +2. Download //Factory// backup from your http server and write it:
 +<code bash>
 +wget http://192.168.1.2/factory.bin
 +</code>
 +<code bash>
 +flash erase 0x100000 0x100000
 +</code>
 +<code bash>
 +flash write 0x100000 0x80001000 0x100000
 +</code>
 +
 +3. Download //u-boot bootloader// backup from your http server and write it:
 +
 +**<color #ed1c24>The most dangerous part of the instruction. Be extremely careful.</color>**
 +
 +<code bash>
 +wget http://192.168.1.2/uboot.bin
 +</code>
 +<code bash>
 +flash erase 0x0 0x100000
 +</code>
 +<code bash>
 +flash write 0x0 0x80001000 0x100000
 +</code>
 +
 +4. Check written data and reboot:
 +<code bash>
 +flash dump 0x0
 +</code>
 +<code bash>
 +flash dump 0x100000
 +</code>
 +
 +5. Use [[:toh:wifire:s1500_nbn#sercomm-recovery_utility]] utility for stock firmware recovery
  
  
 ===== Bootlogs ===== ===== Bootlogs =====
 +
 ==== OEM bootlog ==== ==== OEM bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE</nowiki>+<nowiki>=================================================================== 
 +                MT7621   stage1 code 10:40:45 (ASIC) 
 +                CPU=50000000 HZ BUS=16666666 HZ 
 +================================================================== 
 +Change MPLL source from XTAL to CR... 
 +do MEMPLL setting.. 
 +MEMPLL Config : 0x11100000 
 +3PLL mode + External loopback 
 +=== XTAL-40Mhz === DDR-1200Mhz === 
 +PLL3 FB_DL: 0xa, 1/0 = 524/500 29000000 
 +PLL2 FB_DL: 0xf, 1/0 = 515/509 3D000000 
 +MEMPLL 3PLL mode calibration fail 
 +do DDR setting..[00320381] 
 +Apply DDR3 Setting...(use customer AC) 
 +          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120 
 +      -------------------------------------------------------------------------------- 
 +0000:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0001:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0002:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0003:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0004:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0005:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0006:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0007:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0008:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0009:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000A:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000B:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000C:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000D:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000E:   0    0    0    0    0    0    0    0    0    0    0    1    1    1    1    1 
 +000F:   0    0    0    0    0    1    1    1    1    1    1    1    1    1    1    1 
 +0010:   1    1    1    1    1    1    1    1    1    1    1    0    0    0    0    0 
 +0011:   1    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0 
 +0012:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0013:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0014:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0015:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0016:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0017:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0018:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0019:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001A:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001B:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001C:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001D:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001E:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001F:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +rank 0 coarse = 16 
 +rank 0 fine = 40 
 +B:|    0    0    0    0    0    0    0    0    0    1    1    1    0    0    0    0 
 +opt_dle value:10 
 +DRAMC_R0DELDLY[018]=00002223 
 +================================================================== 
 +                RX      DQS perbit delay software calibration 
 +================================================================== 
 +1.0-15 bit dq delay value 
 +================================================================== 
 +bit|      1  2  3  4  5  6  7  8  9 
 +-------------------------------------- 
 +0 |    10 9 10 10 7 7 9 6 5 7 
 +10 |    8 9 9 10 8 10 
 +-------------------------------------- 
 + 
 +================================================================== 
 +2.dqs window 
 +x=pass dqs delay value (min~max)center 
 +y=0-7bit DQ of every group 
 +input delay:DQS0 =35 DQS1 = 34 
 +================================================================== 
 +bit     DQS0     bit      DQS1 
 +0  (1~66)33  8  (1~66)33 
 +1  (1~69)35  9  (1~68)34 
 +2  (1~68)34  10  (1~67)34 
 +3  (1~66)33  11  (1~66)33 
 +4  (1~65)33  12  (1~66)33 
 +5  (1~68)34  13  (1~66)33 
 +6  (1~66)33  14  (1~68)34 
 +7  (1~66)33  15  (1~67)34 
 +================================================================== 
 +3.dq delay value last 
 +================================================================== 
 +bit|    0  1  2  3  4  5  6  7  8   9 
 +-------------------------------------- 
 +0 |    12 9 11 12 9 8 11 8 6 7 
 +10 |    8 10 10 11 8 10 
 +================================================================== 
 +================================================================== 
 +     TX  perbyte calibration 
 +================================================================== 
 +DQS loop = 15, cmp_err_1 = ffff0000 
 +dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1 
 +dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2 
 +DQ loop=15, cmp_err_1 = ffff0000 
 +dqs_perbyte_dly.last_dqdly_pass[0]=15,  finish count=1 
 +dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=2 
 +byte:0, (DQS,DQ)=(8,8) 
 +byte:1, (DQS,DQ)=(8,8) 
 +20,data:88 
 +[EMI] DRAMC calibration passed 
 + 
 +=================================================================== 
 +                MT7621   stage1 code done 
 +                CPU=50000000 HZ BUS=16666666 HZ 
 +=================================================================== 
 + 
 + 
 +U-Boot 1.1.3 (Apr 22 2016 - 16:35:20) 
 + 
 +Board: Ralink APSoC DRAM:  128 MB 
 +relocate_code Pointer at: 87fac000 
 + 
 +Config XHCI 40M PLL 
 +Allocate 16 byte aligned buffer: 87fe0050 
 +Enable NFI Clock 
 +# MTK NAND # : Use HW ECC 
 +NAND ID [C8 D1 80 95 40] 
 +Device not found, ID: c8d1 
 +Not Support this Device! 
 +chip_mode=00000001 
 +Support this Device in MTK table! c8d1 
 +select_chip 
 +[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 
 +Signature matched and data read! 
 +load_fact_bbt success 2047 
 +load fact bbt success 
 +[mtk_nand] probe successfully! 
 +mtd->writesize=2048 mtd->oobsize=64,    mtd->erasesize=131072  devinfo.iowidth=8 
 +Env addr : 0x80000 
 +..============================================ 
 +Ralink UBoot Version: 4.2.0.6 
 +-------------------------------------------- 
 +ASIC MT7621A DualCore (MAC to MT7530 Mode) 
 +DRAM_CONF_FROM: Auto-Detection 
 +DRAM_TYPE: DDR3 
 +DRAM bus: 16 bit 
 +Xtal Mode=3 OCP Ratio=1/3 
 +Flash component: NAND Flash 
 +Date:Apr 22 2016  Time:16:35:20 
 +============================================ 
 +icache: sets:256, ways:4, linesz:32 ,total:32768 
 +dcache: sets:256, ways:4, linesz:32 ,total:32768 
 + 
 + ##### The CPU freq = 880 MHZ #### 
 + estimate memory size =128 Mbytes 
 +#Reset_MT7530 
 +set LAN/WAN LLLLW 
 +..Example expects ABI version 2 
 +Actual U-Boot ABI version 2 
 + 
 +****************************************** 
 +    Uboot StandAlone Entry 
 +****************************************** 
 +0, cmd 
 +1, 0x0000000D 
 +cmd : 0x0000000D 
 + 
 + 
 +Press Ctrl+C to Enter the Main loop... 
 + 0 Example expects ABI version 2 
 +Actual U-Boot ABI version 2 
 + 
 +****************************************** 
 +    Uboot StandAlone Entry 
 +****************************************** 
 +0, boot 
 +Flash Sector Number : 1024. 
 + 
 +*************************************************** 
 +    Sercomm Boot Version 1.14.0 
 + 
 +*************************************************** 
 +Entering Firmware : Everything is OK. 
 +Begin to verify the backup image... 
 +kernel addr: 0x1B00100  len: 0x2614B4  crc: 0x88174A8C 
 +........................................calculate_kernel_crc: 0x88174A8C 
 +ok! 
 +Second image selected 
 +kernel addr :0xc1700100 
 +kernel addr :0xC1700100 
 +## Booting image at c1700100 ... 
 +   Image Name:   Linux Kernel Image 
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed) 
 +   Data Size:    2495604 Bytes =  2.4 MB 
 +   Load Address: 80001000 
 +   Entry Point:  8000f540 
 +.......................................   Verifying Checksum ... OK 
 +   Uncompressing Kernel Image ... OK 
 + 
 + 
 + 
 +commandline in boot is : console=ttyS1,57600 ubi.mtd=8 root=ubi0:rootfs rw rootfstype=ubifs  !!!! 
 + 
 + 
 + 
 +No initrd 
 +## Transferring control to Linux (at address 8000f540) ... 
 +## Giving linux memsize in MB, 128 
 + 
 +Starting kernel ... 
 + 
 + 
 +LINUX started... 
 + 
 + THIS IS ASIC 
 +Linux version 2.6.36+ (evan_dai@ubuntu) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP PREEMPT Tue Apr 26 22:33:56 CST 2016 
 + 
 + The CPU feqenuce set to 880 MHz 
 +GCMP present 
 +CPU revision is: 0001992f (MIPS 1004Kc) 
 +Software DMA cache coherency 
 +Determined physical RAM map: 
 + memory: 08000000 @ 00000000 (usable) 
 +Zone PFN ranges: 
 +  Normal   0x00000000 -> 0x00008000 
 +Movable zone start PFN for each node 
 +early_node_map[1] active PFN ranges 
 +    0: 0x00000000 -> 0x00008000 
 +Detected 3 available secondary CPU(s) 
 +PERCPU: Embedded 7 pages/cpu @81103000 s7040 r8192 d13440 u65536 
 +pcpu-alloc: s7040 r8192 d13440 u65536 alloc=16*4096 
 +pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512 
 +Kernel command line: console=ttyS1,57600 ubi.mtd=8 root=ubi0:rootfs rw rootfstype=ubifs 
 +PID hash table entries: 512 (order: -1, 2048 bytes) 
 +Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) 
 +Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) 
 +Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. 
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 
 +Writing ErrCtl register=00014dce 
 +Readback ErrCtl register=00014dce 
 +Memory: 122300k/131072k available (5288k kernel code, 8772k reserved, 1692k data, 216k init, 0k highmem) 
 +Hierarchical RCU implementation. 
 +        Verbose stalled-CPUs detection is disabled. 
 +NR_IRQS:128 
 +Trying to install interrupt handler for IRQ24 
 +Trying to install interrupt handler for IRQ25 
 +Trying to install interrupt handler for IRQ22 
 +Trying to install interrupt handler for IRQ9 
 +Trying to install interrupt handler for IRQ10 
 +Trying to install interrupt handler for IRQ11 
 +Trying to install interrupt handler for IRQ12 
 +Trying to install interrupt handler for IRQ13 
 +Trying to install interrupt handler for IRQ14 
 +Trying to install interrupt handler for IRQ16 
 +Trying to install interrupt handler for IRQ17 
 +Trying to install interrupt handler for IRQ18 
 +Trying to install interrupt handler for IRQ19 
 +Trying to install interrupt handler for IRQ20 
 +Trying to install interrupt handler for IRQ21 
 +Trying to install interrupt handler for IRQ23 
 +Trying to install interrupt handler for IRQ26 
 +Trying to install interrupt handler for IRQ27 
 +Trying to install interrupt handler for IRQ28 
 +Trying to install interrupt handler for IRQ15 
 +Trying to install interrupt handler for IRQ8 
 +Trying to install interrupt handler for IRQ29 
 +Trying to install interrupt handler for IRQ30 
 +Trying to install interrupt handler for IRQ31 
 +console [ttyS1] enabled 
 +Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) 
 +pid_max: default: 32768 minimum: 301 
 +Mount-cache hash table entries: 512 
 +launch: starting cpu1 
 +launch: cpu1 gone! 
 +CPU revision is: 0001992f (MIPS 1004Kc) 
 +Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. 
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 
 +launch: starting cpu2 
 +launch: cpu2 gone! 
 +CPU revision is: 0001992f (MIPS 1004Kc) 
 +Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. 
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 
 +launch: starting cpu3 
 +launch: cpu3 gone! 
 +CPU revision is: 0001992f (MIPS 1004Kc) 
 +Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. 
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 
 +Brought up 4 CPUs 
 +Synchronize counters across 4 CPUs: done. 
 +NET: Registered protocol family 16 
 +release PCIe RST: RALINK_RSTCTRL = 7000000 
 +PCIE PHY initialize 
 +***** Xtal 40MHz ***** 
 +start MT7621 PCIe register access 
 +RALINK_RSTCTRL = 7000000 
 +RALINK_CLKCFG1 = 77ffeff8 
 + 
 +*************** MT7621 PCIe RC mode ************* 
 +PCIE2 no card, disable it(RST&CLK) 
 +pcie_link status = 0x3 
 +RALINK_RSTCTRL= 3000000 
 +*** Configure Device number setting of Virtual PCI-PCI bridge *** 
 +RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 
 +PCIE0 enabled 
 +PCIE1 enabled 
 +interrupt enable status: 300000 
 +Port 1 N_FTS = 1b105000 
 +Port 0 N_FTS = 1b105000 
 +config reg done 
 +init_rt2880pci done 
 +bio: create slab <bio-0> at 0 
 +vgaarb: loaded 
 +SCSI subsystem initialized 
 +usbcore: registered new interface driver usbfs 
 +usbcore: registered new interface driver hub 
 +usbcore: registered new device driver usb 
 +pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) 
 +pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) 
 +pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] 
 +pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] 
 +pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] 
 +pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] 
 +pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] 
 +pci 0000:00:00.0: BAR 1: set to [mem 0x60400000-0x6040ffff] (PCI address [0x60400000-0x6040ffff] 
 +pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] 
 +pci 0000:00:01.0: BAR 1: set to [mem 0x60410000-0x6041ffff] (PCI address [0x60410000-0x6041ffff] 
 +pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] 
 +pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] 
 +pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] 
 +pci 0000:00:00.0: PCI bridge to [bus 01-01] 
 +pci 0000:00:00.0:   bridge window [io  disabled] 
 +pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff] 
 +pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref] 
 +pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] 
 +pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff 64bit] (PCI address [0x60200000-0x602fffff] 
 +pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref] 
 +pci 0000:00:01.0: PCI bridge to [bus 02-02] 
 +pci 0000:00:01.0:   bridge window [io  disabled] 
 +pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff] 
 +pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref] 
 +PCI: Enabling device 0000:00:00.0 (0004 -> 0006) 
 +PCI: Enabling device 0000:00:01.0 (0004 -> 0006) 
 +BAR0 at slot 0 = 0 
 +bus=0x0, slot = 0x0 
 +res[0]->start = 0 
 +res[0]->end = 0 
 +res[1]->start = 60400000 
 +res[1]->end = 6040ffff 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +BAR0 at slot 1 = 0 
 +bus=0x0, slot = 0x1 
 +res[0]->start = 0 
 +res[0]->end = 0 
 +res[1]->start = 60410000 
 +res[1]->end = 6041ffff 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +bus=0x1, slot = 0x0, irq=0x4 
 +res[0]->start = 60000000 
 +res[0]->end = 600fffff 
 +res[1]->start = 0 
 +res[1]->end = 0 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +bus=0x2, slot = 0x1, irq=0x18 
 +res[0]->start = 60200000 
 +res[0]->end = 602fffff 
 +res[1]->start = 0 
 +res[1]->end = 0 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +Switching to clocksource MIPS 
 +NET: Registered protocol family 2 
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +TCP established hash table entries: 4096 (order: 3, 32768 bytes) 
 +TCP bind hash table entries: 4096 (order: 4, 81920 bytes) 
 +TCP: Hash tables configured (established 4096 bind 4096) 
 +TCP reno registered 
 +UDP hash table entries: 128 (order: 0, 6144 bytes) 
 +UDP-Lite hash table entries: 128 (order: 0, 6144 bytes) 
 +NET: Registered protocol family 1 
 +4 CPUs re-calibrate udelay(lpj = 1167360) 
 +squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +NTFS driver 2.1.29 [Flags: R/W]. 
 +fuse init (API version 7.15) 
 +msgmni has been set to 238 
 +Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) 
 +io scheduler noop registered (default) 
 +Ralink gpio driver initialized 
 +Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled 
 +serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A 
 +serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A 
 +brd: module loaded 
 +MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error 
 +Allocate 16 byte aligned buffer: 8073c9d0 
 +Enable NFI Clock 
 +# MTK NAND # : Use HW ECC 
 +NAND ID [C8 D1 80 95 40, 00809540] 
 +Device not found, ID: c8d1 
 +Not Support this Device! 
 +chip_mode=00000001 
 +[NAND] pagesz:2048 , oobsz: 288,eccbytes: 32 
 +Support this Device in MTK table! c8d1 
 +NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit) 
 +[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 
 +Signature matched and data read! 
 +load_fact_bbt success 1023 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
 +mtd: partition "BCT" extends beyond the end of device "MT7621-NAND" -- size truncated to 0x380000 
 +[mtk_nand] probe successfully! 
 +UBI: attaching mtd8 to ubi0 
 +UBI: physical eraseblock size:   131072 bytes (128 KiB) 
 +UBI: logical eraseblock size:    126976 bytes 
 +UBI: smallest flash I/O unit:    2048 
 +UBI: VID header offset:          2048 (aligned 2048) 
 +UBI: data offset:                4096 
 +UBI: max. sequence number:       28 
 +UBI: attached mtd8 to ubi0 
 +UBI: MTD device name:            "RootFS_2" 
 +UBI: MTD device size:            46 MiB 
 +UBI: number of good PEBs:        368 
 +UBI: number of bad PEBs:         0 
 +UBI: max. allowed volumes:       128 
 +UBI: wear-leveling threshold:    4096 
 +UBI: number of internal volumes: 1 
 +UBI: number of user volumes:     1 
 +UBI: available PEBs:             0 
 +UBI: total number of reserved PEBs: 368 
 +UBI: number of PEBs reserved for bad PEB handling: 3 
 +UBI: max/mean erase counter: 2/0 
 +UBI: image sequence number: 
 +UBI: background thread "ubi_bgt0d" started, PID 52 
 +GMAC1_MAC_ADRH -- : 0x0000000c 
 +GMAC1_MAC_ADRL -- : 0x4328800b 
 +Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500! 
 +GMAC1_MAC_ADRH -- : 0x0000000c 
 +GMAC1_MAC_ADRL -- : 0x432880c5 
 +PROC INIT OK! 
 +PPP generic driver version 2.4.2 
 +PPP BSD Compression module registered 
 +PPP MPPE Compression module registered 
 +NET: Registered protocol family 24 
 +PPTP driver version 0.8.5 
 +IMQ driver loaded successfully. 
 +        Hooking IMQ after NAT on PREROUTING. 
 +        Hooking IMQ before NAT on POSTROUTING. 
 +usbcore: registered new interface driver catc 
 +catc: v2.8:CATC EL1210A NetMate USB Ethernet driver 
 +usbcore: registered new interface driver asix 
 +usbcore: registered new interface driver ax88179_178a 
 +usbcore: registered new interface driver cdc_ether 
 +usbcore: registered new interface driver net1080 
 +usbcore: registered new interface driver cdc_subset 
 +usbcore: registered new interface driver zaurus 
 +register rt2860 
 + 
 + 
 +=== pAd = c0202000, size = 1428136 === 
 + 
 +<-- RTMPAllocTxRxRingMemory, Status=0 
 +<-- RTMPAllocAdapterBlock, Status=0 
 +pAd->CSRBaseAddress =0xc0100000, csr_addr=0xc0100000! 
 +device_id =0x7662 
 +==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a 
 +====> mt76x2_ePA_per_rate_compensate_init: 5165 is_ePA: 1 
 +RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 
 +RtmpEepromGetDefault::e2p_dafault=2 
 +NVM is FLASH mode 
 + 
 + 
 +=== pAd = c0482000, size = 1428136 === 
 + 
 +<-- RTMPAllocTxRxRingMemory, Status=0 
 +<-- RTMPAllocAdapterBlock, Status=0 
 +pAd->CSRBaseAddress =0xc0380000, csr_addr=0xc0380000! 
 +device_id =0x7662 
 +==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a 
 +====> mt76x2_ePA_per_rate_compensate_init: 5165 is_ePA: 1 
 +RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 
 +RtmpEepromGetDefault::e2p_dafault=2 
 +NVM is FLASH mode 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +xhc_mtk xhc_mtk: xHCI Host Controller 
 +xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 
 +xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 
 +usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 
 +usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 
 +usb usb1: Product: xHCI Host Controller 
 +usb usb1: Manufacturer: Linux 2.6.36+ xhci-hcd 
 +usb usb1: SerialNumber: xhc_mtk 
 +hub 1-0:1.0: USB hub found 
 +hub 1-0:1.0: 2 ports detected 
 +xhc_mtk xhc_mtk: xHCI Host Controller 
 +xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 
 +usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 
 +usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 
 +usb usb2: Product: xHCI Host Controller 
 +usb usb2: Manufacturer: Linux 2.6.36+ xhci-hcd 
 +usb usb2: SerialNumber: xhc_mtk 
 +hub 2-0:1.0: USB hub found 
 +hub 2-0:1.0: 1 port detected 
 +Initializing USB Mass Storage driver... 
 +usbcore: registered new interface driver usb-storage 
 +USB Mass Storage support registered. 
 +Ralink APSoC Hardware Watchdog Timer 
 +Netfilter messages via NETLINK v0.30. 
 +nf_conntrack version 0.5.0 (1910 buckets, 7640 max) 
 +GRE over IPv4 demultiplexor driver 
 +gre: can't add protocol 
 +ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux 
 +TCP cubic registered 
 +NET: Registered protocol family 10 
 +lo: Disabled Privacy Extensions 
 +ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +NET: Registered protocol family 17 
 +Bridge firewalling registered 
 +Ebtables v2.0 registered 
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> 
 +All bugs added by David S. Miller <davem@redhat.com> 
 +UBIFS: mounted UBI device 0, volume 0, name "rootfs" 
 +UBIFS: file system size:   44441600 bytes (43400 KiB, 42 MiB, 350 LEBs) 
 +UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) 
 +UBIFS: media format:       w4/r0 (latest is w4/r0) 
 +UBIFS: default compressor: zlib 
 +UBIFS: reserved for root:  0 bytes (0 KiB) 
 +VFS: Mounted root (ubifs filesystem) on device 0:12. 
 +Started WatchDog Timer. 
 +Freeing unused kernel memory: 216k freed 
 +init started: BusyBox v1.15.3 () 
 +starting pid 62, tty '': '/etc/rcS' 
 +Algorithmics/MIPS FPU Emulator v1.5 
 +UBI: attaching mtd3 to ubi3 
 +UBI: physical eraseblock size:   131072 bytes (128 KiB) 
 +UBI: logical eraseblock size:    126976 bytes 
 +UBI: smallest flash I/O unit:    2048 
 +UBI: VID header offset:          2048 (aligned 2048) 
 +UBI: data offset:                4096 
 +UBI: max. sequence number:       60 
 +UBI: attached mtd3 to ubi3 
 +UBI: MTD device name:            "sys_data" 
 +UBI: MTD device size:            20 MiB 
 +UBI: number of good PEBs:        160 
 +UBI: number of bad PEBs:         0 
 +UBI: max. allowed volumes:       128 
 +UBI: wear-leveling threshold:    4096 
 +UBI: number of internal volumes: 1 
 +UBI: number of user volumes:     1 
 +UBI: available PEBs:             0 
 +UBI: total number of reserved PEBs: 160 
 +UBI: number of PEBs reserved for bad PEB handling: 2 
 +UBI: max/mean erase counter: 2/0 
 +UBI: image sequence number:  1244055123 
 +UBI: background thread "ubi_bgt3d" started, PID 101 
 +UBI device number 3, total 160 LEBs (20316160 bytes, 19.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) 
 +UBIFS: recovery needed 
 +UBIFS: recovery completed 
 +UBIFS: mounted UBI device 3, volume 0, name "xml_config" 
 +UBIFS: file system size:   18157568 bytes (17732 KiB, 17 MiB, 143 LEBs) 
 +UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) 
 +UBIFS: media format:       w4/r0 (latest is w4/r0) 
 +UBIFS: default compressor: zlib 
 +UBIFS: reserved for root:  0 bytes (0 KiB) 
 +sc_drv: module license 'Sercomm' taints kernel. 
 +Disabling lock debugging due to kernel taint 
 +starting pid 109, tty '': '/sbin/getty ttyS1 57600' 
 +Raeth v3.1 (Tasklet) 
 +phy_free_head is 0x72dc000!!! 
 +phy_free_tail_phy is 0x72ddff0!!! 
 +txd_pool=a72de000 phy_txd_pool=072DE000 
 +ei_local->skb_free start address is 0x87f1d4d4. 
 +free_txd: a72de010, ei_local->cpu_ptr: 072DE000 
 + POOL  HEAD_PTR | DMA_PTR | CPU_PTR 
 +----------------+---------+-------- 
 +     0xa72de000 0x072DE000 0x072DE000 
 + 
 +phy_qrx_ring = 0x072d5000, qrx_ring = 0xa72d5000 
 + 
 +phy_rx_ring0 = 0x072e0000, rx_ring0 = 0xa72e0000 
 +change HW-TRAP to 0x17ccf 
 +set LAN/WAN LLLLW 
 +GMAC1_MAC_ADRH -- : 0x0000e060 
 +GMAC1_MAC_ADRL -- : 0x66543201 
 +CDMA_CSG_CFG = 81000000 
 +GDMA1_FWD_CFG = 20710000 
 +switch reg write offset=2004, value=ff0003 
 +switch reg write offset=2104, value=ff0003 
 +switch reg write offset=2204, value=ff0003 
 +switch reg write offset=2304, value=ff0003 
 +switch reg write offset=2404, value=ff0003 
 +switch reg write offset=2504, value=ff0003 
 +switch reg write offset=2010, value=810000c0 
 +switch reg write offset=2110, value=810000c0 
 +switch reg write offset=2210, value=810000c0 
 +switch reg write offset=2310, value=810000c0 
 +switch reg write offset=2410, value=810000c0 
 +switch reg write offset=2510, value=810000c0 
 +switch reg write offset=2610, value=81000000 
 +switch reg write offset=2710, value=81000000 
 +switch reg write offset=2604, value=20ff0003 
 +switch reg write offset=2704, value=20ff0003 
 +Special Tag Disabled 
 +switch reg write offset=2610, value=81000000 
 +switch reg write offset=2014, value=10001 
 +switch reg write offset=2114, value=10001 
 +switch reg write offset=2214, value=10001 
 +switch reg write offset=2314, value=10001 
 +switch reg write offset=2414, value=10002 
 +switch reg write offset=2514, value=10001 
 +REG_ESW_WT_MAC_ATC is 0x7ff0002 
 +done. 
 + 
 +(none) login: ap_name=syslogd, action=start 
 +init common module successful 
 +insert firewall block module success 
 +netfilter tcp syn flood module loaded 
 +netfilter other dos module loaded 
 +netfilter brdcstSrc dos module loaded 
 +ap_name=dnrd, action=start 
 +ap_name=phy, action=start 
 +switch reg write offset=2014, value=10002 
 +switch reg write offset=2114, value=10001 
 +switch reg write offset=2214, value=10001 
 +switch reg write offset=2314, value=10001 
 +switch reg write offset=2414, value=10002 
 +switch reg write offset=2614, value=10001 
 +REG_ESW_WT_MAC_ATC is 0x7ff0002 
 +done. 
 +Set: phy[0].reg[0] = 3300 
 +Set: phy[1].reg[0] = 3300 
 +Set: phy[2].reg[0] = 3300 
 +Set: phy[3].reg[0] = 3300 
 +interface eth2.1 does not exist! 
 +Set: phy[31].reg[24] = 2ff70 
 +Set: phy[31].reg[12512] = 2125 
 +ap_name=wlan, action=start 
 +ap_name=lanip, action=start 
 +ap_name=firewall, action=start 
 +build time = 
 +20141115060606a 
 +rom patch for E3 IC 
 + 
 +platform = 
 +ALPS 
 +hw/sw version = 
 +�� 
 +patch version = 
 + 
 +FW Version:0.0.00 Build:1 
 +Build Time:201411280941____ 
 +fw for E3 IC 
 +RX[0] DESC a76c2000 size = 4096 
 +RX[1] DESC a76c3000 size = 4096 
 +E2pAccessMode=2 
 +cfg_mode=9 
 +cfg_mode=9 
 +wmode_band_equal(): Band Equal! 
 +APSDCapable[0]=0 
 +APSDCapable[1]=0 
 +APSDCapable[2]=0 
 +APSDCapable[3]=0 
 +APSDCapable[4]=0 
 +APSDCapable[5]=0 
 +APSDCapable[6]=0 
 +APSDCapable[7]=0 
 +APSDCapable[8]=0 
 +APSDCapable[9]=0 
 +lan interface=[br0], index=10 
 +APSDCapable[10]=0 
 +APSDCapable[11]=0 
 +APSDCapable[12]=0 
 +APSDCapable[13]=0 
 +APSDCapable[14]=0 
 +APSDCapable[15]=0 
 +Key2Str is Invalid key length(0) or Type(0) 
 +Key3Str is Invalid key length(0) or Type(0) 
 +Key4Str is Invalid key length(0) or Type(0) 
 +RtmpOSFileOpen(): Error 2 opening /etc_ro/Wireless/iNIC/SingleSKU.dat 
 +--> Error opening /etc_ro/Wireless/iNIC/SingleSKU.dat 
 +1. Phy Mode = 14 
 +get_chl_grp:illegal channel (167) 
 +get_chl_grp:illegal channel (167) 
 +get_chl_grp:illegal channel (169) 
 +get_chl_grp:illegal channel (169) 
 +get_chl_grp:illegal channel (171) 
 +get_chl_grp:illegal channel (171) 
 +drivers/net/wireless/rlt_wifi_ibf/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2976 assert (ad->TxPower[choffset].Channel == 42)failed 
 +Country Region from e2p = ffff 
 +mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 
 +mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 
 +mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 
 +2. Phy Mode = 14 
 +3. Phy Mode = 14 
 +andes_pci_fw_init 
 +0x1300 = 00073200 
 +AntCfgInit: primary/secondary ant 0/1 
 +andes_load_cr:cr_type(2) 
 +ChipStructAssign(): MT76x2 hook ! 
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +MCS Set = ff ff 00 00 01 
 +TX0 power compensation = 0x38 
 +TX1 power compensation = 0x38 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +SYNC - BBP R4 to 20MHz.l 
 +mt76x2_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=4, HT-CentCh=4, VHT-CentCh=0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x24, delta_power = 0x0 
 +APStartUp(): AP Set CentralFreq at 4(Prim=4, HT-CentCh=4, VHT-CentCh=0, BBP_BW=0) 
 +Main bssid = e0:60:66:54:32:02 
 +mt76x2_reinit_agc_gain:original agc_vga0 = 0x5e, agc_vga1 = 0x5e 
 +mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5e, agc_vga1 = 0x5e 
 +mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 
 +mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 
 +<==== rt28xx_init, Status=0 
 +RTMPDrvOpen(1):Check if PDMA is idle! 
 +RTMPDrvOpen(2):Check if PDMA is idle! 
 +build time = 
 +20141115060606a 
 +rom patch for E3 IC 
 + 
 +platform = 
 +ALPS 
 +hw/sw version = 
 +�� 
 +patch version = 
 + 
 +FW Version:0.0.00 Build:1 
 +Build Time:201411280941____ 
 +fw for E3 IC 
 +RX[0] DESC a74fd000 size = 4096 
 +RX[1] DESC a74fe000 size = 4096 
 +E2pAccessMode=2 
 +cfg_mode=14 
 +cfg_mode=14 
 +wmode_band_equal(): Band Not Equal! 
 +APSDCapable[0]=0 
 +APSDCapable[1]=0 
 +APSDCapable[2]=0 
 +APSDCapable[3]=0 
 +APSDCapable[4]=0 
 +APSDCapable[5]=0 
 +APSDCapable[6]=0 
 +APSDCapable[7]=0 
 +APSDCapable[8]=0 
 +APSDCapable[9]=0 
 +APSDCapable[10]=0 
 +APSDCapable[11]=0 
 +APSDCapable[12]=0 
 +APSDCapable[13]=0 
 +APSDCapable[14]=0 
 +APSDCapable[15]=0 
 +Key1Str is Invalid key length(0) or Type(0) 
 +Key3Str is Invalid key length(0) or Type(0) 
 +Key4Str is Invalid key length(0) or Type(0) 
 +RtmpOSFileOpen(): Error 2 opening /etc_ro/Wireless/iNIC/SingleSKU.dat 
 +--> Error opening /etc_ro/Wireless/iNIC/SingleSKU.dat 
 +1. Phy Mode = 49 
 +get_chl_grp:illegal channel (167) 
 +get_chl_grp:illegal channel (167) 
 +get_chl_grp:illegal channel (169) 
 +get_chl_grp:illegal channel (169) 
 +get_chl_grp:illegal channel (171) 
 +get_chl_grp:illegal channel (171) 
 +drivers/net/wireless/rlt_wifi_ibf/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2976 assert (ad->TxPower[choffset].Channel == 42)failed 
 +Country Region from e2p = ffff 
 +mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 
 +mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 
 +mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 
 +mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 
 +2. Phy Mode = 49 
 +3. Phy Mode = 49 
 +andes_pci_fw_init 
 +0x1300 = 00073200 
 +AntCfgInit: primary/secondary ant 0/1 
 +andes_load_cr:cr_type(2) 
 +ChipStructAssign(): MT76x2 hook ! 
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +MCS Set = ff ff 00 00 01 
 +TX0 power compensation = 0x38 
 +TX1 power compensation = 0x38 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x19, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x19, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x19, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x19, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 
 +mt76x2_single_sku::DefaultTargetPwr = 0x1b, delta_power = 0x0 
 +APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) 
 +Main bssid = e0:60:66:54:32:03 
 +mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c 
 +mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c 
 +mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 
 +mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 
 +<==== rt28xx_init, Status=0 
 +RTMPDrvOpen(1):Check if PDMA is idle! 
 +RTMPDrvOpen(2):Check if PDMA is idle! 
 +ap_name=networkmap, action=start 
 +ap_name=hw_nat, action=start 
 +ap_name=qtbl, action=start 
 +Insert quick routing module ... 
 + ######DUMP QUICK TABLE FUNC ADDR####### 
 + skb_dev_in_qtl:c31cb788 
 + CheckSumModify:c31ca000 
 + update_conntrack_time:c31ca518 
 + matchFromLan:c31ca558 
 + matchFromWan:c31cab9c 
 + doMatch:c31cbe88 
 + MyCheckSum:c31ca104 
 + CheckSumDlt:c31ca14c 
 + checkEntry:c31cb670 
 + delEntry:c31ca3d8 
 + addEntry:c31cb4f4 
 + checkValidQTEntry:c31ca2f8 
 + updateQtlWhenPktXmit:c31cb828 
 + qtbl_read_proc:c31cb158 
 + qtbl_write_proc:c31cb0d4 
 + ######DUMP QUICK TABLE FUNC ADDR END####### 
 +ap_name=qos, action=start 
 +ap_name=qos_cls, action=start 
 +set offset 214 as b44 for sch rate control. 
 +set offset 214 as e440b44 for sch rate control. 
 +sch 
 +set offset 84 as 80000000 for sch selection. 
 +resv 
 +set offset 80 as 3232 for reservation. 
 +rate 
 +set offset 84 as 80000000 for rate control. 
 +sch 
 +set offset 94 as 80000000 for sch selection. 
 +rate 
 +set offset 94 as 80000000 for rate control. 
 +resv 
 +set offset 90 as 3232 for reservation. 
 +sch 
 +set offset a4 as 80000000 for sch selection. 
 +rate 
 +set offset a4 as 80000000 for rate control. 
 +resv 
 +set offset a0 as 3232 for reservation. 
 +sch 
 +set offset b4 as 80000000 for sch selection. 
 +resv 
 +set offset b0 as 3232 for reservation. 
 +rate 
 +set offset b4 as 80000000 for rate control. 
 +sch 
 +set offset c4 as 80000000 for sch selection. 
 +resv 
 +set offset c0 as 3232 for reservation. 
 +rate 
 +set offset c4 as 80000000 for rate control. 
 +sch 
 +set offset d4 as 80000000 for sch selection. 
 +resv 
 +set offset d0 as 3232 for reservation. 
 +rate 
 +set offset d4 as 80000000 for rate control. 
 +sch 
 +set offset e4 as 80000000 for sch selection. 
 +resv 
 +set offset e0 as 3232 for reservation. 
 +rate 
 +set offset e4 as 80000000 for rate control. 
 +sch 
 +set offset f4 as 80000000 for sch selection. 
 +resv 
 +set offset f0 as 3232 for reservation. 
 +rate 
 +set offset f4 as 80000000 for rate control. 
 +set queue mapping: skb with mark 8 to queue 8. 
 +set queue mapping: skb with mark 9 to queue 9. 
 +set queue mapping: skb with mark a to queue 10. 
 +set queue mapping: skb with mark a to queue 11. 
 +set queue mapping: skb with mark c to queue 12. 
 +set queue mapping: skb with mark d to queue 13. 
 +set queue mapping: skb with mark e to queue 14. 
 +set queue mapping: skb with mark f to queue 15. 
 +sch 
 +set offset 4 as 0 for sch selection. 
 +resv 
 +set offset 0 as 3232 for reservation. 
 +rate 
 +set offset 4 as 8000e44 for rate control. 
 +weight 
 +set offset 4 as 8001e44 for max rate weight. 
 +set queue mapping: skb with mark 0 to queue 0. 
 +sch 
 +set offset 14 as 0 for sch selection. 
 +resv 
 +set offset 10 as 3232 for reservation. 
 +rate 
 +set offset 14 as 8000e44 for rate control. 
 +weight 
 +set offset 14 as 8004e44 for max rate weight. 
 +set queue mapping: skb with mark 1 to queue 1. 
 +sch 
 +set offset 24 as 0 for sch selection. 
 +resv 
 +set offset 20 as 3232 for reservation. 
 +rate 
 +set offset 24 as 8000e44 for rate control. 
 +weight 
 +set offset 24 as 8004e44 for max rate weight. 
 +set queue mapping: skb with mark 2 to queue 2. 
 +sch 
 +set offset 34 as 0 for sch selection. 
 +resv 
 +set offset 30 as 3232 for reservation. 
 +rate 
 +set offset 34 as 0 for rate control. 
 +set queue mapping: skb with mark 3 to queue 3. 
 +set offset 214 as e440b44 for sch rate control. 
 +set offset 214 as e440b44 for sch rate control. 
 +sch 
 +set offset 84 as 80000000 for sch selection. 
 +resv 
 +set offset 80 as 3232 for reservation. 
 +rate 
 +set offset 84 as 80000000 for rate control. 
 +sch 
 +set offset 94 as 80000000 for sch selection. 
 +rate 
 +set offset 94 as 80000000 for rate control. 
 +resv 
 +set offset 90 as 3232 for reservation. 
 +sch 
 +set offset a4 as 80000000 for sch selection. 
 +rate 
 +set offset a4 as 80000000 for rate control. 
 +resv 
 +set offset a0 as 3232 for reservation. 
 +sch 
 +set offset b4 as 80000000 for sch selection. 
 +resv 
 +set offset b0 as 3232 for reservation. 
 +rate 
 +set offset b4 as 80000000 for rate control. 
 +sch 
 +set offset c4 as 80000000 for sch selection. 
 +resv 
 +set offset c0 as 3232 for reservation. 
 +rate 
 +set offset c4 as 80000000 for rate control. 
 +sch 
 +set offset d4 as 80000000 for sch selection. 
 +resv 
 +set offset d0 as 3232 for reservation. 
 +rate 
 +set offset d4 as 80000000 for rate control. 
 +sch 
 +set offset e4 as 80000000 for sch selection. 
 +resv 
 +set offset e0 as 3232 for reservation. 
 +rate 
 +set offset e4 as 80000000 for rate control. 
 +sch 
 +set offset f4 as 80000000 for sch selection. 
 +resv 
 +set offset f0 as 3232 for reservation. 
 +rate 
 +set offset f4 as 80000000 for rate control. 
 +set queue mapping: skb with mark 8 to queue 8. 
 +set queue mapping: skb with mark 9 to queue 9. 
 +set queue mapping: skb with mark a to queue 10. 
 +set queue mapping: skb with mark a to queue 11. 
 +set queue mapping: skb with mark c to queue 12. 
 +set queue mapping: skb with mark d to queue 13. 
 +set queue mapping: skb with mark e to queue 14. 
 +set queue mapping: skb with mark f to queue 15. 
 +sch 
 +set offset 4 as 8001e44 for sch selection. 
 +resv 
 +set offset 0 as 3232 for reservation. 
 +rate 
 +set offset 4 as 8001e44 for rate control. 
 +weight 
 +set offset 4 as 8001e44 for max rate weight. 
 +set queue mapping: skb with mark 0 to queue 0. 
 +sch 
 +set offset 14 as 8004e44 for sch selection. 
 +resv 
 +set offset 10 as 3232 for reservation. 
 +rate 
 +set offset 14 as 8004e44 for rate control. 
 +weight 
 +set offset 14 as 8004e44 for max rate weight. 
 +set queue mapping: skb with mark 1 to queue 1. 
 +sch 
 +set offset 24 as 8004e44 for sch selection. 
 +resv 
 +set offset 20 as 3232 for reservation. 
 +rate 
 +set offset 24 as 8004e44 for rate control. 
 +weight 
 +set offset 24 as 8004e44 for max rate weight. 
 +set queue mapping: skb with mark 2 to queue 2. 
 +sch 
 +set offset 34 as 0 for sch selection. 
 +resv 
 +set offset 30 as 3232 for reservation. 
 +rate 
 +set offset 34 as 0 for rate control. 
 +set queue mapping: skb with mark 3 to queue 3. 
 +set offset 214 as e440b44 for sch rate control. 
 +set offset 214 as e440b44 for sch rate control. 
 +sch 
 +set offset 84 as 80000000 for sch selection. 
 +resv 
 +set offset 80 as 3232 for reservation. 
 +rate 
 +set offset 84 as 80000000 for rate control. 
 +sch 
 +set offset 94 as 80000000 for sch selection. 
 +rate 
 +set offset 94 as 80000000 for rate control. 
 +resv 
 +set offset 90 as 3232 for reservation. 
 +sch 
 +set offset a4 as 80000000 for sch selection. 
 +rate 
 +set offset a4 as 80000000 for rate control. 
 +resv 
 +set offset a0 as 3232 for reservation. 
 +sch 
 +set offset b4 as 80000000 for sch selection. 
 +resv 
 +set offset b0 as 3232 for reservation. 
 +rate 
 +set offset b4 as 80000000 for rate control. 
 +sch 
 +set offset c4 as 80000000 for sch selection. 
 +resv 
 +set offset c0 as 3232 for reservation. 
 +rate 
 +set offset c4 as 80000000 for rate control. 
 +sch 
 +set offset d4 as 80000000 for sch selection. 
 +resv 
 +set offset d0 as 3232 for reservation. 
 +rate 
 +set offset d4 as 80000000 for rate control. 
 +sch 
 +set offset e4 as 80000000 for sch selection. 
 +resv 
 +set offset e0 as 3232 for reservation. 
 +rate 
 +set offset e4 as 80000000 for rate control. 
 +sch 
 +set offset f4 as 80000000 for sch selection. 
 +resv 
 +set offset f0 as 3232 for reservation. 
 +rate 
 +set offset f4 as 80000000 for rate control. 
 +set queue mapping: skb with mark 8 to queue 8. 
 +set queue mapping: skb with mark 9 to queue 9. 
 +set queue mapping: skb with mark a to queue 10. 
 +set queue mapping: skb with mark a to queue 11. 
 +set queue mapping: skb with mark c to queue 12. 
 +set queue mapping: skb with mark d to queue 13. 
 +set queue mapping: skb with mark e to queue 14. 
 +set queue mapping: skb with mark f to queue 15. 
 +sch 
 +set offset 4 as 8001e44 for sch selection. 
 +resv 
 +set offset 0 as 3232 for reservation. 
 +rate 
 +set offset 4 as 8001e44 for rate control. 
 +weight 
 +set offset 4 as 8001e44 for max rate weight. 
 +set queue mapping: skb with mark 0 to queue 0. 
 +sch 
 +set offset 14 as 8004e44 for sch selection. 
 +resv 
 +set offset 10 as 3232 for reservation. 
 +rate 
 +set offset 14 as 8004e44 for rate control. 
 +weight 
 +set offset 14 as 8004e44 for max rate weight. 
 +set queue mapping: skb with mark 1 to queue 1. 
 +sch 
 +set offset 24 as 8004e44 for sch selection. 
 +resv 
 +set offset 20 as 3232 for reservation. 
 +rate 
 +set offset 24 as 8004e44 for rate control. 
 +weight 
 +set offset 24 as 8004e44 for max rate weight. 
 +set queue mapping: skb with mark 2 to queue 2. 
 +sch 
 +set offset 34 as 0 for sch selection. 
 +resv 
 +set offset 30 as 3232 for reservation. 
 +rate 
 +set offset 34 as 0 for rate control. 
 +set queue mapping: skb with mark 3 to queue 3. 
 +ap_name=cpm, action=start 
 +ap_name=wanip, action=stop 
 +ap_name=dnrd, action=stop 
 +ap_name=dnrd, action=stop 
 +Tue Apr 26 23:18:10 UTC 2016 
 +ap_name=httpd, action=start 
 +ap_name=coredump, action=start 
 +ap_name=srt, action=restart 
 +ap_name=rp, action=start 
 +bind: Address already in use 
 +bind: Address already in use 
 +ap_name=udpecho, action=start 
 +ap_name=ntp, action=start 
 +ap_name=ingress_qos, action=start 
 +ap_name=ingress_classify, action=start 
 +ap_name=qos_remark, action=start 
 +ap_name=ipv6wd, action=start 
 +ap_name=telnetd, action=start 
 +ap_name=sshd, action=start 
 +ap_name=ftpd, action=start 
 +ap_name=igd_upnp, action=start 
 +ap_name=dnsr, action=start 
 +ap_name=cron, action=start 
 +Could not load host key: /etc/ssh/ssh_host_ecdsa_key 
 +Could not load host key: /etc/ssh/ssh_host_ed25519_key 
 + 
 +S1500 login: superuser 
 +Password: 
 +Welcome to s1500, you can type '?' to find usage 
 + 
 +view @ s1500> show sysinfo 
 +        Vendor:                       NetByNet 
 +        Model:                        S1500 
 +        CPU:                          MT7621 
 +        Firmware Version:             S1500-v2.0.12 
 +        Lib Version: 
 +        Build Time:                    (build @ 2016-04-26, 23:18:10) 
 +        Hardware Version:             S1500v4 
 +        Bootloader Version:           1.14.0 
 +        Serial Number:                MH16F9876543 
 +        Time Since Last Boot:          0:17:31 
 +        Reboot Cause:                 Unknow 
 +        Product Class:                S1500 
 +        Current Time:                 2016-04-26 23:35:08</nowiki>
 </WRAP>\\ </WRAP>\\
  
 ==== OpenWrt bootlog ==== ==== OpenWrt bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING</nowiki> +<nowiki>=================================================================== 
-</WRAP>\\+                MT7621   stage1 code 10:40:45 (ASIC) 
 +                CPU=50000000 HZ BUS=16666666 HZ 
 +================================================================== 
 +Change MPLL source from XTAL to CR... 
 +do MEMPLL setting.. 
 +MEMPLL Config : 0x11100000 
 +3PLL mode + External loopback 
 +=== XTAL-40Mhz === DDR-1200Mhz === 
 +PLL3 FB_DL: 0xa, 1/0 = 582/442 29000000 
 +PLL2 FB_DL: 0x10, 1/0 = 686/338 41000000 
 +MEMPLL 3PLL mode calibration fail 
 +do DDR setting..[00320381] 
 +Apply DDR3 Setting...(use customer AC) 
 +          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120 
 +      -------------------------------------------------------------------------------- 
 +0000:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0001:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0002:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0003:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0004:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0005:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0006:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0007:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0008:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0009:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000A:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000B:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000C:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000D:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +000E:   0    0    0    0    0    0    0    0    0    0    0    1    1    1    1    1 
 +000F:   0    0    0    0    0    1    1    1    1    1    1    1    1    1    1    1 
 +0010:   1    1    1    1    1    1    1    1    1    1    0    0    0    0    0    0 
 +0011:   1    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0 
 +0012:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0013:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0014:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0015:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0016:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0017:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0018:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +0019:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001A:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001B:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001C:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001D:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001E:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +001F:   0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0 
 +rank 0 coarse = 15 
 +rank 0 fine = 80 
 +B:|    0    0    0    0    0    0    0    0    0    0    1    1    1    0    0    0 
 +opt_dle value:11 
 +DRAMC_R0DELDLY[018]=00002222 
 +================================================================== 
 +                RX      DQS perbit delay software calibration  
 +================================================================== 
 +1.0-15 bit dq delay value 
 +================================================================== 
 +bit|      1  2  3  4  5  6  7  8  9 
 +-------------------------------------- 
 +0 |    10 9 10 10 7 7 9 6 5 7  
 +10 |    8 9 9 10 8 10  
 +--------------------------------------
  
 +==================================================================
 +2.dqs window
 +x=pass dqs delay value (min~max)center 
 +y=0-7bit DQ of every group
 +input delay:DQS0 =34 DQS1 = 34
 +==================================================================
 +bit     DQS0     bit      DQS1
 +0  (0~66)33  8  (1~66)33
 +1  (1~68)34  9  (1~66)33
 +2  (1~66)33  10  (1~67)34
 +3  (1~64)32  11  (1~62)31
 +4  (1~64)32  12  (1~66)33
 +5  (1~66)33  13  (1~64)32
 +6  (1~66)33  14  (1~68)34
 +7  (1~66)33  15  (1~67)34
 +==================================================================
 +3.dq delay value last
 +==================================================================
 +bit|    0  1  2  3  4  5  6  7  8   9
 +--------------------------------------
 +0 |    11 9 11 12 9 8 10 7 6 8 
 +10 |    8 12 10 12 8 10 
 +==================================================================
 +==================================================================
 +     TX  perbyte calibration 
 +==================================================================
 +DQS loop = 15, cmp_err_1 = ffff0000 
 +dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1 
 +dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2 
 +DQ loop=15, cmp_err_1 = ffff0000
 +dqs_perbyte_dly.last_dqdly_pass[0]=15,  finish count=1 
 +dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=2 
 +byte:0, (DQS,DQ)=(8,8)
 +byte:1, (DQS,DQ)=(8,8)
 +20,data:88
 +[EMI] DRAMC calibration passed
 +
 +===================================================================
 +                MT7621   stage1 code done 
 +                CPU=50000000 HZ BUS=16666666 HZ
 +===================================================================
 +
 +
 +U-Boot 1.1.3 (Apr 22 2016 - 16:35:20)
 +
 +Board: Ralink APSoC DRAM:  128 MB
 +relocate_code Pointer at: 87fac000
 +
 +Config XHCI 40M PLL 
 +******************************
 +Software System Reset Occurred
 +******************************
 +Allocate 16 byte aligned buffer: 87fe0050
 +Enable NFI Clock
 +# MTK NAND # : Use HW ECC
 +NAND ID [C8 D1 80 95 40]
 +Device not found, ID: c8d1
 +Not Support this Device! 
 +chip_mode=00000001
 +Support this Device in MTK table! c8d1 
 +select_chip
 +[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
 +Signature matched and data read!
 +load_fact_bbt success 2047
 +load fact bbt success
 +[mtk_nand] probe successfully!
 +mtd->writesize=2048 mtd->oobsize=64,    mtd->erasesize=131072  devinfo.iowidth=8
 +Env addr : 0x80000
 +..============================================ 
 +Ralink UBoot Version: 4.2.0.6
 +-------------------------------------------- 
 +ASIC MT7621A DualCore (MAC to MT7530 Mode)
 +DRAM_CONF_FROM: Auto-Detection 
 +DRAM_TYPE: DDR3 
 +DRAM bus: 16 bit
 +Xtal Mode=3 OCP Ratio=1/3
 +Flash component: NAND Flash
 +Date:Apr 22 2016  Time:16:35:20
 +============================================ 
 +icache: sets:256, ways:4, linesz:32 ,total:32768
 +dcache: sets:256, ways:4, linesz:32 ,total:32768 
 +
 + ##### The CPU freq = 880 MHZ #### 
 + estimate memory size =128 Mbytes
 +#Reset_MT7530
 +set LAN/WAN LLLLW
 +..Example expects ABI version 2
 +Actual U-Boot ABI version 2
 +
 +******************************************
 +    Uboot StandAlone Entry
 +******************************************
 +0, cmd
 +1, 0x0000000D
 +cmd : 0x0000000D
 +
 +
 +Press Ctrl+C to Enter the Main loop...
 + 0 Example expects ABI version 2
 +Actual U-Boot ABI version 2
 +
 +******************************************
 +    Uboot StandAlone Entry
 +******************************************
 +0, boot
 +Flash Sector Number : 1024.
 +
 +***************************************************
 +    Sercomm Boot Version 1.14.0
 +
 +***************************************************
 +Entering Firmware : Everything is OK.
 +Begin to verify the default image... 
 +kernel addr: 0x1700100  len: 0x2A4229  crc: 0x5BFFDF87
 +............................................calculate_kernel_crc: 0x5BFFDF87
 +ok!
 +First image selected
 +kernel addr :0xc1300100 
 +kernel addr :0xC1300100 
 +## Booting image at c1300100 ...
 +   Image Name:   MIPS OpenWrt Linux-5.10.115
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    2769385 Bytes =  2.6 MB
 +   Load Address: 80001000
 +   Entry Point:  80001000
 +...........................................   Verifying Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 + 
 +
 +
 +commandline in boot is : console=ttyS1,57600 ubi.mtd=7 root=ubi0:rootfs rw rootfstype=ubifs  !!!!
 +
 +
 +
 +No initrd
 +## Transferring control to Linux (at address 80001000) ...
 +## Giving linux memsize in MB, 128
 +
 +Starting kernel ...
 +
 +
 +
 +OpenWrt kernel loader for MIPS based SoC
 +Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
 +Decompressing kernel... done!
 +Starting kernel at 80001000...
 +
 +[    0.000000] Linux version 5.10.115 (ubuntu@z) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19623-4b1d5a65de) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sun May 29 18:57:08 2022
 +[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
 +[    0.000000] printk: bootconsole [early0] enabled
 +[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
 +[    0.000000] MIPS: machine is WiFire S1500.NBN
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] VPE topology {2,2} total 4
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
 +[    0.000000] Zone ranges:
 +[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
 +[    0.000000]   HighMem  empty
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
 +[    0.000000] percpu: Embedded 15 pages/cpu s30096 r8192 d23152 u61440
 +[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
 +[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
 +[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
 +[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
 +[    0.000000] Writing ErrCtl register=00014dc0
 +[    0.000000] Readback ErrCtl register=00014dc0
 +[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
 +[    0.000000] Memory: 119280K/131072K available (6714K kernel code, 620K rwdata, 1360K rodata, 1276K init, 235K bss, 11792K reserved, 0K cma-reserved, 0K highmem)
 +[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
 +[    0.000000] rcu: Hierarchical RCU implementation.
 +[    0.000000]  Tracing variant of Tasks RCU enabled.
 +[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
 +[    0.000000] NR_IRQS: 256
 +[    0.000000] random: get_random_bytes called from start_kernel+0x3cc/0x5e4 with crng_init=0
 +[    0.000000] CPU Clock: 880MHz
 +[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
 +[    0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
 +[    0.015865] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
 +[    0.033727] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
 +[    0.106059] pid_max: default: 32768 minimum: 301
 +[    0.115371] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.129777] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.147791] rcu: Hierarchical SRCU implementation.
 +[    0.157564] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
 +[    0.173052] smp: Bringing up secondary CPUs ...
 +[    0.182620] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.182631] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +[    0.182643] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
 +[    0.182764] CPU1 revision is: 0001992f (MIPS 1004Kc)
 +[    0.242972] Synchronize counters for CPU 1: done.
 +[    0.305002] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.305011] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +[    0.305018] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
 +[    0.305062] CPU2 revision is: 0001992f (MIPS 1004Kc)
 +[    0.363964] Synchronize counters for CPU 2: done.
 +[    0.424170] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.424179] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +[    0.424186] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
 +[    0.424236] CPU3 revision is: 0001992f (MIPS 1004Kc)
 +[    0.483536] Synchronize counters for CPU 3: done.
 +[    0.543143] smp: Brought up 1 node, 4 CPUs
 +[    0.555604] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
 +[    0.575109] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
 +[    0.588933] pinctrl core: initialized pinctrl subsystem
 +[    0.601003] NET: Registered protocol family 16
 +[    0.612196] cpuidle: using governor teo
 +[    0.643194] random: fast init done
 +[    0.663034] clocksource: Switched to clocksource GIC
 +[    0.674853] NET: Registered protocol family 2
 +[    0.683709] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
 +[    0.698656] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
 +[    0.715218] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.730367] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
 +[    0.744384] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.757097] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
 +[    0.769983] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
 +[    0.784024] NET: Registered protocol family 1
 +[    0.792562] PCI: CLS 0 bytes, default 32
 +[    0.802809] workingset: timestamp_bits=14 max_order=15 bucket_order=1
 +[    0.819660] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.831142] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.852870] mt7621_gpio 1e000600.gpio: registering 32 gpios
 +[    0.864380] mt7621_gpio 1e000600.gpio: registering 32 gpios
 +[    0.875735] mt7621_gpio 1e000600.gpio: registering 32 gpios
 +[    0.887717] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
 +[    0.901856] printk: console [ttyS0] disabled
 +[    0.910342] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
 +[    0.928252] printk: console [ttyS0] enabled
 +[    0.928252] printk: console [ttyS0] enabled
 +[    0.944802] printk: bootconsole [early0] disabled
 +[    0.944802] printk: bootconsole [early0] disabled
 +[    0.965839] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
 +[    0.978562] nand: ESMT NAND 128MiB 3,3V 8-bit
 +[    0.987400] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
 +[    1.002484] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
 +[    1.015604] 12 fixed-partitions partitions found on MTD device mt7621-nand
 +[    1.029299] Creating 12 MTD partitions on "mt7621-nand":
 +[    1.039886] 0x000000000000-0x000007f80000 : "ALL"
 +[    3.012012] 0x000000000000-0x000000100000 : "Bootloader"
 +[    3.039210] 0x000000100000-0x000000200000 : "Factory"
 +[    3.066097] 0x000000200000-0x000001600000 : "sys_data"
 +[    3.385057] 0x000001600000-0x000001700000 : "boot_flag"
 +[    3.412137] 0x000001700000-0x000001b00000 : "kernel"
 +[    3.484606] 0x000001b00000-0x000001f00000 : "Kernel_2"
 +[    3.557389] 0x000001f00000-0x000004d00000 : "RootFS_1"
 +[    4.276344] 0x000004d00000-0x000007b00000 : "RootFS_2"
 +[    4.995190] 0x000007b00000-0x000007c00000 : "Ftool"
 +[    5.021295] 0x000007c00000-0x000007f80000 : "BCT"
 +[    5.085605] 0x000000080000-0x0000000a0000 : "BootLoad-Env"
 +[    5.106833] Concatenating MTD devices:
 +[    5.114377] (0): "RootFS_1"
 +[    5.119928] (1): "sys_data"
 +[    5.125495] (2): "Ftool"
 +[    5.130521] (3): "BCT"
 +[    5.135210] into device "ubi-concat"
 +[    5.142359] 1 fixed-partitions partitions found on MTD device ubi-concat
 +[    5.155698] Creating 1 MTD partitions on "ubi-concat":
 +[    5.165937] 0x000000000000-0x000004680000 : "ubi"
 +[    6.305337] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
 +[    6.321650] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
 +[    6.339530] i2c /dev entries driver
 +[    6.349056] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
 +[    6.362456] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
 +[    6.379992] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
 +[    6.396296] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
 +[    6.412680] mt7621-pci 1e140000.pcie: Parsing DT failed
 +[    6.425444] NET: Registered protocol family 10
 +[    6.435816] Segment Routing with IPv6
 +[    6.443265] NET: Registered protocol family 17
 +[    6.452530] 8021q: 802.1Q VLAN Support v1.8
 +[    6.464413] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
 +[    6.496411] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26)
 +[    6.518534] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
 +[    6.540589] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
 +[    6.562660] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
 +[    6.584820] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30)
 +[    6.606992] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
 +[    6.623861] DSA: tree 0 setup
 +[    6.630075] rt2880-pinmux pinctrl: pcie is already enabled
 +[    6.641171] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
 +[    6.654571] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
 +[    6.672104] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
 +[    6.688414] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
 +[    6.704812] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
 +[    6.719915] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
 +[    6.734921] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
 +[    6.849576] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
 +[    6.860696] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
 +[    6.972022] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
 +[    6.985904] mt7621-pci 1e140000.pcie: PCIE0 enabled
 +[    6.995630] mt7621-pci 1e140000.pcie: PCIE1 enabled
 +[    7.005352] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
 +[    7.024072] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
 +[    7.036759] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
 +[    7.050468] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
 +[    7.064174] pci_bus 0000:00: root bus resource [bus 00-ff]
 +[    7.075113] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
 +[    7.095427] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
 +[    7.107427] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
 +[    7.119923] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
 +[    7.132477] pci 0000:00:00.0: supports D1
 +[    7.140468] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
 +[    7.152719] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
 +[    7.164751] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
 +[    7.177248] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
 +[    7.189793] pci 0000:00:01.0: supports D1
 +[    7.197786] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
 +[    7.211339] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
 +[    7.223398] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
 +[    7.237459] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
 +[    7.249979] pci 0000:01:00.0: reg 0x30: initial BAR value 0x00000000 invalid
 +[    7.264031] pci 0000:01:00.0: reg 0x30: [mem size 0x00010000 pref]
 +[    7.276451] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
 +[    7.290515] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
 +[    7.300966] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
 +[    7.313112] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
 +[    7.326640] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
 +[    7.341031] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
 +[    7.354478] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
 +[    7.366503] pci 0000:02:00.0: reg 0x10: [mem 0x60200000-0x602fffff 64bit]
 +[    7.380078] pci 0000:02:00.0: reg 0x30: initial BAR value 0x00000000 invalid
 +[    7.394124] pci 0000:02:00.0: reg 0x30: [mem size 0x00010000 pref]
 +[    7.406541] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
 +[    7.420631] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
 +[    7.431082] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
 +[    7.443229] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
 +[    7.456758] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
 +[    7.471150] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
 +[    7.484393] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
 +[    7.497574] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
 +[    7.511445] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
 +[    7.524625] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
 +[    7.538501] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
 +[    7.552035] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
 +[    7.566430] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
 +[    7.579961] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
 +[    7.594353] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
 +[    7.607897] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
 +[    7.621425] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
 +[    7.634954] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
 +[    7.648493] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
 +[    7.663079] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
 +[    7.677470] pci 0000:00:00.0: PCI bridge to [bus 01]
 +[    7.687363] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
 +[    7.700891] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
 +[    7.714417] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
 +[    7.728827] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
 +[    7.743403] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
 +[    7.757793] pci 0000:00:01.0: PCI bridge to [bus 02]
 +[    7.767685] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
 +[    7.781213] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
 +[    7.794747] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
 +[    7.813533] UBI: auto-attach mtd12
 +[    7.820332] ubi0: attaching mtd12
 +[    7.827261] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
 +[    7.943413] UBI: EOF marker found, PEBs from 33 will be erased
 +[    8.974645] ubi0: scanning is finished
 +[    9.030494] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 517 LEBs
 +[    9.044544] ubi0: attached mtd12 (name "ubi", size 70 MiB)
 +[    9.055503] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
 +[    9.069189] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
 +[    9.082707] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
 +[    9.096569] ubi0: good PEBs: 564, bad PEBs: 0, corrupted PEBs: 0
 +[    9.108524] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
 +[    9.122909] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1653850628
 +[    9.141097] ubi0: available PEBs: 0, total reserved PEBs: 564, PEBs reserved for bad PEB handling: 12
 +[    9.159491] ubi0: background thread "ubi_bgt0d" started, PID 451
 +[    9.161835] block ubiblock0_0: created from ubi0:0(rootfs)
 +[    9.182485] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
 +[    9.254784] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
 +[    9.274818] Freeing unused kernel memory: 1276K
 +[    9.283898] This architecture does not have kernel memory protection.
 +[    9.296748] Run /sbin/init as init process
 +[   10.196733] init: Console is alive
 +[   10.204007] init: - watchdog -
 +[   11.576627] kmodloader: loading kernel modules from /etc/modules-boot.d/*
 +[   11.765977] usbcore: registered new interface driver usbfs
 +[   11.777085] usbcore: registered new interface driver hub
 +[   11.787892] usbcore: registered new device driver usb
 +[   11.808902] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
 +[   11.823978] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
 +[   11.839314] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
 +[   11.849947] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
 +[   11.873186] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
 +[   11.891454] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
 +[   11.904263] hub 1-0:1.0: USB hub found
 +[   11.911883] hub 1-0:1.0: 2 ports detected
 +[   11.920609] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
 +[   11.931284] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
 +[   11.946264] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
 +[   11.959156] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
 +[   11.976226] hub 2-0:1.0: USB hub found
 +[   11.983865] hub 2-0:1.0: 1 port detected
 +[   12.001089] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
 +[   12.033527] init: - preinit -
 +[   13.227472] random: jshn: uninitialized urandom read (4 bytes read)
 +[   13.314811] random: jshn: uninitialized urandom read (4 bytes read)
 +[   13.412744] random: jshn: uninitialized urandom read (4 bytes read)
 +[   13.911650] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
 +[   13.928086] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   13.933362] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
 +[   13.958442] 8021q: adding VLAN 0 to HW filter on device lan1
 +[   13.972362] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +[   18.193571] UBIFS (ubi0:1): default file-system created
 +[   18.205367] UBIFS (ubi0:1): Mounting in unauthenticated mode
 +[   18.216951] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 595
 +[   18.345861] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
 +[   18.361486] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
 +[   18.381232] UBIFS (ubi0:1): FS size: 64376832 bytes (61 MiB, 507 LEBs), journal size 3174400 bytes (3 MiB, 25 LEBs)
 +[   18.402015] UBIFS (ubi0:1): reserved for root: 3040676 bytes (2969 KiB)
 +[   18.415193] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 93C44890-6220-4B05-B3D2-C53F9B0FDF2C, small LPT model
 +[   18.441106] mount_root: overlay filesystem has not been fully initialized yet
 +[   18.456231] mount_root: switching to ubifs overlay
 +[   18.474405] urandom-seed: Seed file not found (/etc/urandom.seed)
 +[   18.594612] procd: - early -
 +[   18.600594] procd: - watchdog -
 +[   19.253248] procd: - watchdog -
 +[   19.366550] procd: - ubus -
 +[   19.546596] procd: - init -
 +Please press Enter to activate this console.
 +[   20.338738] kmodloader: loading kernel modules from /etc/modules.d/*
 +[   20.538101] urngd: v1.0.2 started.
 +[   20.643566] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
 +[   20.658689] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
 +[   20.727951] random: crng init done
 +[   20.734786] random: 7 urandom warning(s) missed due to ratelimiting
 +[   20.883280] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
 +[   20.894088] pci 0000:00:00.0: enabling device (0006 -> 0007)
 +[   20.905385] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002)
 +[   20.917534] mt76x2e 0000:01:00.0: ASIC revision: 76120044
 +[   21.583625] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
 +[   21.599681] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
 +[   21.610662] mt76x2e 0000:01:00.0: Build: 1
 +[   21.618821] mt76x2e 0000:01:00.0: Build Time: 201607111443____
 +[   21.653058] mt76x2e 0000:01:00.0: Firmware running!
 +[   21.668980] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23
 +[   21.679887] pci 0000:00:01.0: enabling device (0006 -> 0007)
 +[   21.691421] mt76x2e 0000:02:00.0: ASIC revision: 76020044
 +[   22.363101] mt76x2e 0000:02:00.0: ROM patch already applied
 +[   22.375045] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
 +[   22.386035] mt76x2e 0000:02:00.0: Build: 1
 +[   22.394244] mt76x2e 0000:02:00.0: Build Time: 201607111443____
 +[   22.409320] mt76x2e 0000:02:00.0: Firmware running!
 +[   22.477520] PPP generic driver version 2.4.2
 +[   22.488059] NET: Registered protocol family 24
 +[   22.506133] kmodloader: done loading kernel modules from /etc/modules.d/*
 +[   45.935134] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
 +[   45.957571] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
 +[   45.974220] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   45.980434] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
 +[   46.005019] 8021q: adding VLAN 0 to HW filter on device lan1
 +[   46.019613] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +[   46.033380] br-lan: port 1(lan1) entered blocking state
 +[   46.043871] br-lan: port 1(lan1) entered disabled state
 +[   46.056157] device lan1 entered promiscuous mode
 +[   46.065422] device eth0 entered promiscuous mode
 +[   46.104867] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
 +[   46.118865] 8021q: adding VLAN 0 to HW filter on device lan2
 +[   46.135497] br-lan: port 2(lan2) entered blocking state
 +[   46.146064] br-lan: port 2(lan2) entered disabled state
 +[   46.158570] device lan2 entered promiscuous mode
 +[   46.183591] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
 +[   46.197815] 8021q: adding VLAN 0 to HW filter on device lan3
 +[   46.212925] br-lan: port 3(lan3) entered blocking state
 +[   46.223510] br-lan: port 3(lan3) entered disabled state
 +[   46.235444] device lan3 entered promiscuous mode
 +[   46.264548] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
 +[   46.278445] 8021q: adding VLAN 0 to HW filter on device lan4
 +[   46.293515] br-lan: port 4(lan4) entered blocking state
 +[   46.304033] br-lan: port 4(lan4) entered disabled state
 +[   46.316290] device lan4 entered promiscuous mode
 +[   46.345534] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
 +[   46.359237] 8021q: adding VLAN 0 to HW filter on device wan
 +[   47.688786] mt7530 mdio-bus:1f lan2: Link is Up - 100Mbps/Full - flow control off
 +[   47.703945] br-lan: port 2(lan2) entered blocking state
 +[   47.714469] br-lan: port 2(lan2) entered forwarding state
 +[   47.727937] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
 +
 +
 +
 +BusyBox v1.35.0 (2022-05-29 18:57:08 UTC) built-in shell (ash)
 +
 +  _______                     ________        __
 +       |.-----.-----.-----.|  |  |  |.----.|  |_
 +     ||  _  |  -__|     ||  |  |  ||   _||   _|
 + |_______||   __|_____|__|__||________||__|  |____|
 +          |__| W I R E L E S S   F R E E D O M
 + -----------------------------------------------------
 + OpenWrt SNAPSHOT, r19711-cc84040cb4
 + -----------------------------------------------------
 +=== WARNING! =====================================
 +There is no root password defined on this device!
 +Use the "passwd" command to set up a new password
 +in order to prevent unauthorized SSH logins.
 +--------------------------------------------------
 +root@OpenWrt:/# ubus call system board
 +{
 +        "kernel": "5.10.115",
 +        "hostname": "OpenWrt",
 +        "system": "MediaTek MT7621 ver:1 eco:3",
 +        "model": "WiFire S1500.NBN",
 +        "board_name": "wifire,s1500-nbn",
 +        "rootfs_type": "squashfs",
 +        "release": {
 +                "distribution": "OpenWrt",
 +                "version": "SNAPSHOT",
 +                "revision": "r19711-cc84040cb4",
 +                "target": "ramips/mt7621",
 +                "description": "OpenWrt SNAPSHOT r19711-cc84040cb4"
 +        }
 +}</nowiki>
 +</WRAP>\\
 ===== Notes ===== ===== Notes =====
  
 ===== Tags ===== ===== Tags =====
 [[meta:tags|How to add tags]] [[meta:tags|How to add tags]]
-{{tag>EXAMPLETAG unsupported}}+{{tagpage>U-boot}} 
 +{{tagpage>2core}} 
 +{{tagpage>MT7621}} 
 +{{tagpage>GigabitEthernet}} 
 +{{tagpage>1NIC}} 
 +{{tagpage>5Port}} 
 +{{tagpage>2WNIC}} 
 +{{tagpage>802.11ac}} 
 +{{tagpage>802.11abgn}} 
 +{{tagpage>InternalAntenna}} 
 +{{tagpage>4Ant}} 
 +{{tagpage>128RAM}} 
 +{{tagpage>128NAND}} 
 +{{tagpage>USB2.0}} 
 +{{tagpage>USB}} 
 +{{tagpage>1USB}} 
 +{{tagpage>JTAG}} 
 +{{tagpage>Serial}} 
 +{{tagpage>GPIO}} 
 +{{tagpage>2button}} 
 +{{tagpage>12v_powered}} 
 +{{tagpage>Dual_firmware}}
  • Last modified: 2024/09/05 19:03
  • by csharper2005