Western Digital My Net WiFi Range Extender

This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 4/32 warning for details.

1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.

2) OpenWrt support for this device has ended in 2022.
19.07.10 was the last official build for 4/32 devices.

Manufacturer Link: http://www.wdc.com/en/products/products.aspx?id=890 FIXME Dead link --- tmomas 2017/01/02 12:29

GPL Source code: http://support.wdc.com/product/download.asp?groupid=1708&sid=190&lang=en

  • Platform: DB120

Western Digital My Net WiFi Range Extender Flash Layout
Layer0 m25p80 spi0.0: m25p64 8192KiB
Layer1 mtd0 u-boot 256KiB mtd1 firmware 7808KiB mtd2 nvram 64KiB mtd3 art 64KiB
Layer2 kernel 960KiB mtd4 rootfs 6848KiB
mountpoint /
filesystem mini_fo/overlayfs
Layer3 mtd3 rootfs_data 5184KiB
Size in KiB 256KiB 960KiB 1536KiB 5184KiB 64KiB 64KiB
Name u-boot kernel rootfs_data nvram art
mountpoint none none /rom /overlay none none
filesystem none none SquashFS JFFS2 none none

Can be flashed from the original web interface with factory file as shown above.

Set a PC on same network to some address in IP range 192.168.1.[2-254]. Download either WD or OpenWrt factory firmware image as shown above, store as code.bin (file name is important). From serial console abort the U-boot process. Enter this on u-boot command line

ar7100> upgrade code.bin
Tftpd start listening on port[69]!

Send file from windows PC with TFTP:

C:\tmp> tftp -i 192.168.1.230 put code.bin

For linux TFTP

tftp 192.168.1.230 69
tftp> binary
tftp> put code.bin

You should see this on console wait for flash to finish:

Receiving firmware [code.bin] from [192.168.1.10]
Write File : CODE.BIN

Once U-boot command prompt returns enter

ar7100 > go

generic.sysupgrade

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the sysupgrade command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. If flashing the device has left you with a damaged ART (calibration data for the wifi) and/or nvram (ethernet and wifi MACs) partition, you can download an emergency emergency.tar.gz replacement and flash them manually again to restore your device.

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

  • Login as root via SSH on 192.168.1.1
  • Use the following commands to upgrade.
cd /tmp/
wget <firmwarefile as shown above>
sysupgrade /tmp/xxx.abc

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, etc.

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
wlan0 WiFi Disabled

hardware.button on howto use and configure the hardware button(s).

The Range Extender has two programmable buttons and a switch. The buttons are Reset, the WiFi Protected Setup Push Button. The switch has no function, the original firmware uses it to select whenever the wifi should operate in the 5GHz or 2.4GHz band. Here, we merely name the buttons, so we can use them in the above Howto:

BUTTON Event
Reset reset
WPS wps

The UART is accessable via JP1 (which hasn't a header connected). You will need a TTL to RS232 (ie a MAX232 circuit) to utilize this. The pinout is:
[GND] [RxD] [TxD] [3.3v]
DJ1

Looking under the main 'can', the CPU is:
Atheros AR7370-BC2A PGX842_00B 1221 TAIWAN

Next to that, there's a 256MBit RAM chip:
winbond W9725G6KB-25 6146A53AQZZ2 218PUA TWN

The Flash Rom chip:
winbond 25Q64FVSIG 1236

Top of mainboard:

Antenna Layout:

SoC and RAM:

UART header and Flash-Rom:

Modified Range Extender with external RP-SMA Connectors:

Linux version 2.6.31 (root@tabulator) (gcc version 4.3.3 (GCC) ) #159 Tue Oct 22 16:50:45 CEST 2013 flash_size passed from bootloader = 8 arg 1: console=ttyS0,115200 arg 2: root=31:04 arg 3: rootfstype=squashfs arg 4: init=/sbin/init arg 5: mtdparts=ath-nor0:256k(u-boot),7808k(linux),64k(nvram),64k(ART),64k(filesystem) arg 6: fsoffset=0xd0000 arg 7: mem=32M CPU revision is: 0001974c (MIPS 74Kc) ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 400 ahb 200 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 02000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00002000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00002000 On node 0 totalpages: 8192 free_area_init_node: node 0, pgdat 80224290, node_mem_map 81000000 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8128 pages, LIFO batch:0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS0,115200 root=31:04 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),7808k(linux),64k(nvram),64k(ART),64k(filesystem) fsoffset=0xd0000 mem=32M PID hash table entries: 128 (order: 7, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 23928k/32768k available (1751k kernel code, 8840k reserved, 441k data, 116k init, 0k highmem) NR_IRQS:128 plat_time_init: plat time init done Calibrating delay loop... 279.55 BogoMIPS (lpj=559104) Mount-cache hash table entries: 512 ****************ALLOC*********************** Packet mem: 80254aa0 (0x600000 bytes) ******************************************** NET: Registered protocol family 16 PCI init:ath_pcibios_init ath_pcibios_init(294): PCI CMD write: 0x356 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 pci 0000:00:00.0: reg 10 64bit mmio: [0x000000-0x01ffff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] pci 0000:00:00.0: supports D1 pci 0000:00:00.0: PME# supported from D0 D1 D3hot pci 0000:00:00.0: PME# disabled Returning IRQ 64 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 squashfs: version 4.0 (2009/01/31) Phillip Lougher fuse init (API version 7.12) msgmni has been set to 46 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler deadline registered (default) GPIO_init register done Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled 5 cmdlinepart partitions found on MTD device ath-nor0 Creating 5 MTD partitions on "ath-nor0": 0x000000000000-0x000000040000 : "u-boot" 0x000000040000-0x0000007e0000 : "linux" 0x0000007e0000-0x0000007f0000 : "nvram" 0x0000007f0000-0x000000800000 : "ART" 0x000000110000-0x0000007e0000 : "filesystem" Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 2048 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> athwdt_init: Registering WDT success ath_otp_init: Registering OTP success ath_clksw_init: Registering Clock Switch Interface success Calling get_sb_bdev VFS: Mounted root (squashfs filesystem) readonly on device 31:4. file name /dev/root p squashfs mount_data <NULL> Freeing unused kernel memory: 116k freed ATHR_GMAC: Length per segment 1536 ATHR_GMAC: fifo cfg 3 01f00140 ATHR_GMAC: RX TASKLET - Pkts per Intr:100 ATHR_GMAC: Mac address for unit 0:bfff0000 ATHR_GMAC: ff:ff:ff:ff:ff:ff ATHR_GMAC: Max segments per packet : 1 ATHR_GMAC: Max tx descriptor count : 128 ATHR_GMAC: Max rx descriptor count : 192 ATHR_GMAC: Mac capability flags : 2380 ctmisc: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint Register /dev/ctmisc device, major:10 minor:255 athr_gmac_ring_alloc Allocated 2048 at 0x81de8800 athr_gmac_ring_alloc Allocated 3072 at 0x81d57000 WASP ----> F1e PHY Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... ATHR_AUTONEG_ADVERT:DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:1000 ATHRSF1_PHY: Port 4, Neg Success ATHRSF1_PHY: unit 0 phy addr 4 device eth0 entered promiscuous mode ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ATH_MAC_TIMER: enet unit:0 is up... RGMii 1000Mbps full duplex value 1 ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl WASP ----> F1e PHY Setting Drop CRC Errors, Pause Frames and Length Error frames ath_pci: 9.2.0_U10.5.13 (Atheros/multi-bss) PCI: Setting latency timer of device 0000:00:00.0 to 64 __ath_attach: Set global_scn[0] ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 *** ar9300Attach 630 ar9300NewState *** Restoring Cal data from Flash ath_get_caps[5147] rx chainmask mismatch actual 7 sc_chainmak 0 ath_get_caps[5122] tx chainmask mismatch actual 7 sc_chainmak 0 SC Callback Registration for wifi0 wifi0: Atheros 9380: mem=0x10000000, irq=64 hw_base=0xb0000000 wlan_vap_create : enter. devhandle=0x81fb42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x81fb42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created DES SSID SET=WDRangeExtender ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 VAP device ath1 created device ath0 entered promiscuous mode device ath1 entered promiscuous mode br0: port 3(ath1) entering forwarding state br0: port 2(ath0) entering forwarding state br0: port 1(eth0) entering forwarding state ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1 Scan in progress.. Cancelling it br0: port 2(ath0) entering disabled state DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 br0: port 2(ath0) entering forwarding state WPS Enabled : Ignoring MAC Filtering WPS Enabled : Ignoring MAC Filtering WPS Enabled : Ignoring MAC Filtering WPS Enabled : Ignoring MAC Filtering br0: port 2(ath0) entering disabled state athr_gmac_ring_free Freeing at 0x81de8800 athr_gmac_ring_free Freeing at 0x81d57000 br0: port 1(eth0) entering disabled state device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state br0: port 3(ath1) entering disabled state ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=81b6d9fc arg=81dc7ac0 ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=81b6d9fc arg=81dc7ac0 ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=81b6d6b4 arg=81dc7ac0 device ath0 left promiscuous mode br0: port 2(ath0) entering disabled state ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=81b6d9fc arg=81dc72c0 ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=81b6d9fc arg=81dc72c0 ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=81b6d6b4 arg=81dc72c0 device ath1 left promiscuous mode br0: port 3(ath1) entering disabled state ath_pci: driver unloaded Removing athdebug proc file ath_dev: driver unloaded ath_rate_atheros: driver unloaded ath_hal: driver unloaded athr_gmac_ring_alloc Allocated 2048 at 0x81fa1800 athr_gmac_ring_alloc Allocated 3072 at 0x81d72000 WASP ----> F1e PHY Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... ATHR_AUTONEG_ADVERT:DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:1000 ATHRSF1_PHY: Port 4, Neg Success ATHRSF1_PHY: unit 0 phy addr 4 device eth0 entered promiscuous mode ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ATH_MAC_TIMER: enet unit:0 is up... RGMii 1000Mbps full duplex value 1 ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl WASP ----> F1e PHY Setting Drop CRC Errors, Pause Frames and Length Error frames ath_pci: 9.2.0_U10.5.13 (Atheros/multi-bss) PCI: Setting latency timer of device 0000:00:00.0 to 64 __ath_attach: Set global_scn[0] ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 *** ar9300Attach 630 ar9300NewState *** Restoring Cal data from Flash ath_get_caps[5147] rx chainmask mismatch actual 7 sc_chainmak 0 ath_get_caps[5122] tx chainmask mismatch actual 7 sc_chainmak 0 SC Callback Registration for wifi0 wifi0: Atheros 9380: mem=0x10000000, irq=64 hw_base=0xb0000000 wlan_vap_create : enter. devhandle=0x81fb42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x81fb42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created DES SSID SET=WDRangeExtender ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 VAP device ath1 created Found best 11na chan: 36 device ath0 entered promiscuous mode device ath1 entered promiscuous mode br0: port 3(ath1) entering forwarding state br0: port 2(ath0) entering forwarding state br0: port 1(eth0) entering forwarding state ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, valid=1 br0: port 2(ath0) entering disabled state DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 br0: port 2(ath0) entering forwarding state WPS Enabled : Ignoring MAC Filtering


Linux version 3.14.28 (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43974) ) #10 Thu Jan 15 18:59:15 CET 2015 MyLoader: sysp=2eba3ea2, boardp=3abeabab, parts=aa37abb2 bootconsole [early0] enabled CPU0 revision is: 0001974c (MIPS 74Kc) SoC: Atheros AR9344 rev 2 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone ranges: Normal [mem 0x00000000-0x01ffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x01ffffff] On node 0 totalpages: 8192 free_area_init_node: node 0, pgdat 802f25e0, node_mem_map 81000000 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8192 pages, LIFO batch:0 Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: board=MYNET-REXT console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,7808k(firmware),64k(nvram),64k(ART),6528k@0x140000(filesystem) root=31:4 rootfstype=squashfs,jffs2 noinitrd PID hash table entries: 128 (order: -3, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 28908K/32768K available (2334K kernel code, 124K rwdata, 264K rodata, 212K init, 187K bss, 3860K reserved) SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:51 Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) NET: Registered protocol family 16 MIPS: machine is WD My Net Wi-Fi Range Extender registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] pci_bus 0000:00: root bus resource [io 0x0000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: [168c:0030] type 00 class 0x028000 pci 0000:00:00.0: invalid calibration data pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] pci 0000:00:00.0: supports D1 pci 0000:00:00.0: PME# supported from D0 D1 D3hot pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] pci 0000:00:00.0: using irq 40 for pin 1 Switched to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 PCI: CLS 0 bytes, default 32 futex hash table entries: 256 (order: -1, 3072 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. msgmni has been set to 56 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A console [ttyS0] enabled bootconsole [early0] disabled m25p80 spi0.0: found s25fl064k, expected m25p80 m25p80 spi0.0: s25fl064k (8192 Kbytes) 5 cmdlinepart partitions found on MTD device spi0.0 Creating 5 MTD partitions on "spi0.0": 0x000000000000-0x000000040000 : "u-boot" 0x000000040000-0x0000007e0000 : "firmware" 0x0000007e0000-0x0000007f0000 : "nvram" 0x0000007f0000-0x000000800000 : "ART" 0x000000140000-0x0000007a0000 : "filesystem" libphy: ag71xx_mdio: probed ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd072, driver=Generic PHY] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII TCP: cubic registered NET: Registered protocol family 17 Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. VFS: Mounted root (jffs2 filesystem) readonly on device 31:4. Freeing unused kernel memory: 212K (8030b000 - 80340000) zram: Created 1 device(s) ... usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Button Hotplug driver version 0.4.1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-platform: EHCI generic platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform: OHCI generic platform driver Error: Driver 'gpio-keys-polled' is already registered, aborting... random: mktemp urandom read with 14 bits of entropy available NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_set: protocol 6 hidraw: raw HID events driver (C) Jiri Kosina Loading modules backported from Linux version master-2014-11-04-0-gf3660a2 Backport generated by backports.git backports-20141023-2-g4ff890b Error: Driver 'gpio-keys' is already registered, aborting... Error: Driver 'gpio-keys-polled' is already registered, aborting... ip_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack version 0.5.0 (455 buckets, 1820 max) xt_time: kernel timezone is -0000 Error: Driver 'gpio-keys' is already registered, aborting... cfg80211: Calling CRDA to update world regulatory domain cfg80211: World regulatory domain updated: cfg80211: DFS Master region: unset cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) Error: Driver 'gpio-keys-polled' is already registered, aborting... Error: Driver 'gpio-keys' is already registered, aborting... Error: Driver 'gpio-keys-polled' is already registered, aborting... Error: Driver 'gpio-keys' is already registered, aborting... Error: Driver 'gpio-keys-polled' is already registered, aborting... PCI: Enabling device 0000:00:00.0 (0000 -> 0002) ath: EEPROM regdomain: 0x8114 ath: EEPROM indicates we should expect a country code ath: doing EEPROM country->regdmn map search ath: country maps to regdmn code: 0x37 ath: Country alpha2 being used: DE ath: Regpair used: 0x37 ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40 cfg80211: Calling CRDA for country: DE cfg80211: Regulatory domain changed to country: DE cfg80211: DFS Master region: ETSI cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (N/A) cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s) cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s) cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) Error: Driver 'gpio-keys' is already registered, aborting... Error: Driver 'gpio-keys-polled' is already registered, aborting... Error: Driver 'gpio-keys' is already registered, aborting... Error: Driver 'gpio-keys-polled' is already registered, aborting... Adding 14332k swap on /dev/zram0. Priority:-1 extents:1 across:14332k SS IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready eth0: link up (1000Mbps/Full duplex) IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready random: nonblocking pool is initialized


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1