WAVLINK WL-WN578A2
Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.
Any text with a light background (like this one) provides instructions for creating the Details Page. When you have filled in correct/useful information (instead of any template that's there) remove the instructions, as well as the <WRAP>
that encloses it.
Getting started with a new Device Page
- This is an empty template that suggests the information that should be present on a well-constructed Device Page. This means, that you have to fill it with life and information.
- There are several “fixme” tags with text on a light background (like this text) throughout this template. As you fill in the page, remove those tags so that people can judge its completeness.
- When there are no more “fixme” tags left, delete this one too, along with the
<WRAP>
that encloses it.
Keep the articles modular
- Please include only model specific information, omit bla,bla and put everything generic into separate articles
- If you have no time to write certain stuff, link to docs
- base-system should lead the way, do not explain this again
- DO NOT provide a complete howto here! Instead groom the general documentation.
Supported Versions
Experimental Versions
None at this time.
Hardware Highlights
Installation
Flash Layout
Find out flash layout, then add the flash layout table here (copy, paste, modify the example).
Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.
OEM installation using the TFTP method
Specific values needed for tftp
Enter values for “FILL-IN” below
Bootloader tftp server IPv4 address | FILL-IN |
---|---|
Bootloader MAC address (special) | FILL-IN |
Firmware tftp image | Latest OpenWrt release (NOTE: Name must contain “tftp”) |
TFTP transfer window | FILL-IN seconds |
TFTP window start | approximately FILL-IN seconds after power on |
TFTP client required IP address | FILL-IN |
Upgrading OpenWrt
These are generic instructions. Update with your router's specifics.
LuCI Web Upgrade Process
- Browse to
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/
LuCI Upgrade URL - Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
sysupgrade
mtd
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
mtd
If sysupgrade
does not support this router, use mtd
.
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot
Debricking
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Please fill in real values for this device, then remove the EXAMPLEs
Network interfaces
The default network configuration is:
Interface Name | Description | Default configuration |
---|---|---|
br-lan | EXAMPLE LAN & WiFi | EXAMPLE 192.168.1.1/24 |
vlan0 (eth0.0) | EXAMPLE LAN ports (1 to 4) | EXAMPLE None |
vlan1 (eth0.1) | EXAMPLE WAN port | EXAMPLE DHCP |
wl0 | EXAMPLE WiFi | EXAMPLE Disabled |
Switch Ports (for VLANs)
Please fill in real values for this device, then remove the EXAMPLEs
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
Port | Switch port |
---|---|
Internet (WAN) | EXAMPLE 4 |
LAN 1 | EXAMPLE 3 |
LAN 2 | EXAMPLE 2 |
LAN 3 | EXAMPLE 1 |
LAN 4 | EXAMPLE 0 |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
Please fill in real values for this device, then remove the EXAMPLEs
The WAVLINK WL-WN578A2 has the following buttons:
BUTTON | Event |
---|---|
EXAMPLE Reset | reset |
EXAMPLE Secure Easy Setup | ses |
EXAMPLE No buttons at all. | - |
Hardware
Info
Photos
Front:
Insert photo of front of the casing
Back:
Insert photo of back of the casing
Backside label:
Insert photo of backside label
Opening the case
Note: This will void your warranty!
Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...
- To remove the cover and open the device, do a/b/c
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port
Replace EXAMPLE by real values.
Serial connection parameters for WAVLINK WL-WN578A2 @@Version@@ | EXAMPLE 115200, 8N1 |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootloader mods
Hardware mods
None so far.
Bootlogs
OEM bootlog
COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE
OpenWrt bootlog
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING
Notes
Space for additional notes, links to forum threads or other resources.
- ...
Tags
Add tags below, then remove this fixme.