VTECH NetiaSpot

Router made for polish telecom operator Netia by VTECH, working on modified OpenRG operating system.

VTech NetiaSpot

Unknown!

CPU Ram Flash Network USB Serial JTag
Lantiq ARX168@333MHz 32MiB 64MiB NAND + 512kB SPI 4x 100M + DSL + 1WIFI 2x 2.0 Yes n/a
cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00400000 00004000 "rgloader"
mtd1: 02400000 00004000 "UBI"
mtd2: 01800000 00004000 "JFFS2"
mtd3: 00080000 00001000 "sflash"
mtd4: 0216c000 00003e00 "NETIASPOT"
mtd5: 00550000 00003e00 "mainfs"
flash layout
Section 00 Type UNKNOWN    Range 0x00000000-0x00040000 MaxSize 0x00040000
Flash file: /dev/mtdblock4
MTD partition: sflash
        No more information.

Section 01 Type FACTORY    Range 0x00040000-0x00050000 MaxSize 0x0000FF6C
Flash file: /dev/mtdblock4
MTD partition: sflash
        Size 0x000004FE Name 'rg_factory'
        Checksum 0x00015015 Counter 0x0000006A Start Offset 0x00000000

Section 02 Type BOOTCONF   Range 0x00050000-0x00060000 MaxSize 0x0000FF6C
Flash file: /dev/mtdblock4
MTD partition: sflash
        Uninitialized.

Section 03 Type UNKNOWN    Range 0x0007F000-0x00080000 MaxSize 0x00001000
Flash file: /dev/mtdblock4
MTD partition: sflash
        No more information.

Section 04 Type IMAGE      Range 0x00000000-0x00F23000 MaxSize 0x00F22F6C
Flash file: /dev/mtdblock5
MTD partition: NETIASPOT
        Size 0x00715000 Name 'Image downloaded from: http://77.252.14.142:80/cpe-r/public/382/316694510/openrg_5_4_8_2_45_1_8.rms'
        Checksum 0x37F3C59B Counter 0x000002A5 Start Offset 0x00000000

Section 05 Type IMAGE      Range 0x00F23000-0x01E46000 MaxSize 0x00F22F6C
Flash file: /dev/mtdblock5
MTD partition: NETIASPOT
        Size 0x00716000 Name 'Image downloaded from: http://77.252.14.142:80/cpe-r/public/327/1422792404/openrg_5.4.8.2.45_1_2.rms'
        Checksum 0x37F358F9 Counter 0x00000217 Start Offset 0x00000000

Section 06 Type CONF       Range 0x01E46000-0x01ECDA00 MaxSize 0x0008796C
Flash file: /dev/mtdblock5
MTD partition: NETIASPOT
        Size 0x0000BB80 Name 'rg_conf'
        Checksum 0x005D72ED Counter 0x00000A60 Start Offset 0x00000000

Section 07 Type CONF       Range 0x01ECDA00-0x01F55400 MaxSize 0x0008796C
Flash file: /dev/mtdblock5
MTD partition: NETIASPOT
        Size 0x0000BB85 Name 'rg_conf'
        Checksum 0x005E0D46 Counter 0x00000A63 Start Offset 0x00000000

Section 08 Type LOG        Range 0x01F55400-0x02154C00 MaxSize 0x001FF76C
Flash file: /dev/mtdblock5
MTD partition: NETIASPOT
        Uninitialized.

Total 9 sections found.
Instruction set: MIPS
Vendor: Lantiq
bootloader: U-Boot
System-On-Chip: Lantiq XWAY ARX168
CPU @Frq MIPS 34Kc @333MHz
Flash size: 64 MiB NAND / 512kB SPI
Flash Chip: Toshiba TC58DVM92A5TA00 / ???
RAM size: 32 MiB
RAM Chip: Etrontech EM6AA160TSA-5G
Wireless Baseband/MAC: Lantiq PSB 8224 EL v1.1
Wireless RF: Lantiq PSB 8304 V V1.1
switch: Lantiq PSB 6970 V V1.3
Modem: ADSL / 3G by USB Dongle
USB: Yes 2x 2.0
Serial: Yes
JTAG: n/a

Board:
VTech NetiaSpot board

Note: This device is the property of Netia, you are just borrowing it from them! Unless you didn't buy it from other source, don't open it or modify it!

  • To remove the top cover:
1. Press it in the center and slide to the left
2. Done.
  • To open the router:
1. Remove four rubbers from the bottom
2. Unscrew screws under removed rubbers
3. Pry the cover starting from one place and going around the casing
4. Done.

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Photo of the serial pinout on NetiaSpot board

Use any compatible RS-232 programming cable (tested are Nokia DKU-5 and CA-42 cables based on PL-2303 chip, or Sagem cable based on CP2102 chip). To connect, you can use Putty set on 115200 speed, other settings untouched.

ROM VER: 1.1.3 CFG 05 DDR Access auto data-eye tuning Rev 0.3a DDR size from 0xa0000000 - 0xa1ffffff DDR check ok... start booting... U-Boot 1.1.5-LANTIQ-v-1.8.39 (Apr 4 2011 - 19:51:54) Boot from SPI AR9 BOARD CLOCK CPU 333M RAM 166M DRAM: 32 MB relocate_code start relocate_code finish. 64 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Start init xR9 Mac 0 to 2 mode GPIO25 reset to Eth switch is generated. switch chip id=00002599 Tantos Switch detected!! amazon_s Switch Type "run flash_nfs" to mount root filesystem over NFS Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x0, size 0x400000 ... Reading data from 0x3ffe00 -- 100% complete. OK ## Starting application at 0x80C00000 ... Uncompressing Linux... malloc: 00003E6C returned: 80E92020 .................................................................................................. Done Network boot detected: move image to proper location Running from : (0x80C00008) CramFS will be at: 0x803AD000 Booting the kernel dcache writeback, cachesize 00004000 linesize 00000020 icache invalidate, cachesize 00008000 linesize 00000020 Infineon xDSL CPE AR9 mips_hpt_frequency = 166666666, counter_resolution = 2 Linux version 2.6.21.5 #1 Tue Mar 29 09:07:41 IST 2011 rofs_addr: 00225000 (80225000), len: f0000, flash_start_addr: 00000000 (80000000) flash_len: 0 CramFS found in RAM rofs_start_addr: 00000000 len: 0 phym = 01000000, mem = 00f00000, max_pfn = 00000f00 Reserving memory for CP1 @0xa0f00000, size 0x00100000 CPU revision is: 0001954c Determined physical RAM map: User-defined physical RAM map: memory: 00f00000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 3810 Kernel command line: cramfs=0 slram=mainfs,0x00225000,+983040 console=ttyS1,115200 mtdparts=ifx_nand:4M(rgloader),0x02400000(UBI),-(JFFS2);ifx_sflash:-(sflash) mem=0x00f00000 vpe1_load_addr=0x80f00000 vpe1_mem=0x00100000 1 MIPSR2 register sets available Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH PID hash table entries: 64 (order: 6, 256 bytes) Using 166.667 MHz high precision timer. GPIO configuration for module 4 was not found. Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) Memory: 11412k/15360k available (1763k kernel code, 3948k reserved, 276k data, 148k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 Lantiq PCI host controller driver, version 1.1.5, (c) 2001-2010 Lantiq Deutschland GmbH NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 512 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 512 bind 512) TCP reno registered gptu: totally 6 16-bit timers/counters gptu: misc_register on minor 63 gptu: succeeded to request irq 118 gptu: succeeded to request irq 119 gptu: succeeded to request irq 120 gptu: succeeded to request irq 121 gptu: succeeded to request irq 122 gptu: succeeded to request irq 123 IFX DMA driver, version ifxmips_dma_core.c:v1.0.7 ,(c)2009 Infineon Technologies AG Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH Wired TLB entries for Linux read_c0_wired() = 0 /proc/fs/cramfs_block_uncompressed created io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered loop: loaded (max 8 devices) NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 21 GPIO configuration for module 3 was found. Lantiq SSC driver, version 2.1.5, (c) 2001-2010 Lantiq Deutschland GmbH GPIO configuration for module 4 was not found. ttyS0 at MMIO map 0xbe100400 mem 0xbe100400 (irq = 98) is a IFX_ASC ttyS1 at MMIO map 0xbe100c00 mem 0xbe100c00 (irq = 105) is a IFX_ASC Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH ifx_nand_init Probe for NAND flash... NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks 3 cmdlinepart partitions found on MTD device ifx_nand Creating 3 MTD partitions on "ifx_nand": 0x00000000-0x00400000 : "rgloader" 0x00400000-0x02800000 : "UBI" 0x02800000-0x04000000 : "JFFS2" PMCU initiates! ifx_pmu_init: Major 253 Lantiq PMU driver, version 1.0.6, (c) 2001-2010 Lantiq Deutschland GmbH /home/albert/trees/netia/Netia-5_4_8_2_23_1_2/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16 GPIO configuration for module 20 was found. 1 cmdlinepart partitions found on MTD device ifx_sflash Creating 1 MTD partitions on "ifx_sflash": 0x00000000-0x00080000 : "sflash" Lantiq SPI flash driver, version 1.1.8, (c) 2001-2010 Lantiq Deutschland GmbH Freeing unused kernel memory: 148k freed Found device mainfs on mtdblock0 Version: 5.4.8.2.23.1.2 Platform: Vtech ARX168 based Board Compilation Time: 29-Mar-11 06:58:58 Tag: Ntag-5_4_8_2_23_1_2 Compilation Flags: DIST=RGLOADER_VTECH_ARX168_NETIA User Information: albert@actaeon /home/albert/trees/netia/Netia-5_4_8_2_23_1_2 insmod: add-symbol-file build/debug/kos_lib.o 0xc0011000 -s .data 0xc0017e10 -s .bss 0xc0018c40 kos_lib: module license 'unspecified' taints kernel. loading license key: jungo_rnd UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 16384 bytes (16 KiB) UBI: logical eraseblock size: 15872 bytes UBI: smallest flash I/O unit: 512 UBI: sub-page size: 256 UBI: VID header offset: 256 (aligned 256) UBI: data offset: 512 UBI: attached mtd2 to ubi0 UBI: MTD device name: "UBI" UBI: MTD device size: 36 MiB UBI: number of good PEBs: 2304 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 92 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 46 UBI: total number of reserved PEBs: 2258 UBI: number of PEBs reserved for bad PEB handling: 46 UBI: max/mean erase counter: 27/11 UBI: image sequence number: 22193626 UBI: background thread "ubi_bgt0d" started, PID 16 Press ESC to enter BOOT MENU mode. Can't load valid rg_conf - using defaults MAPS: insmod: add-symbol-file build/debug/krgldr_module.o 0xc001b000 -s .data 0xc001b310 -s .bss 0xc001b4a0 insmod: add-symbol-file build/debug/ifxmips_3port_eth_sw_mod.o 0xc0024000 -s .data 0xc0026860 -s .bss 0xc00269c0 External Switch ID :0x00002599 GPIO configuration for module 25 was not found. IFX 3 Port Switch Eth driver, version ifxmips_3port_sw.c:v1.0.4 ,(c)2009 Infineon Technologies AG RGLoader 5.4.8.2.23.1.2 Booting an active image in 1 seconds Booting image from 0x1000000(0x81000000)... Uncompressing Linux... malloc: 00003E6C returned: 81719014 ............................................................................................................................. Done CramFS in 'NETIASPOT' mtd device. Image offset:00000000 Running from : (0x80002000) CramFS will be at: 0x001C5000 Booting the kernel dcache writeback, cachesize 00004000 linesize 00000020 icache invalidate, cachesize 00008000 linesize 00000020 Infineon xDSL CPE AR9 mips_hpt_frequency = 166666666, counter_resolution = 2 Linux version 2.6.21.5 #1 Tue Jan 24 19:46:28 IST 2012 rofs_addr: 001c5000 (801c5000), len: 550000, flash_start_addr: 00000000 (80000000) flash_len: 0 CramFS in Flash rofs_start_addr: 00000000 len: 0 phym = 02000000, mem = 01f00000, max_pfn = 00001f00 Reserving memory for CP1 @0xa1f00000, size 0x00100000 CPU revision is: 0001954c Determined physical RAM map: User-defined physical RAM map: memory: 01f00000 @ 00000000 (usable) Reserved 256k KLOG memory starting from Physical 0x01ec0000 Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 7874 Kernel command line: cramfs=1 cramfs_offset=001c5000 mtdparts=ifx_nand:4M(rgloader),0x02400000(UBI),-(JFFS2);ifx_sflash:-(sflash);NETIASPOT:0x550000@0x001c5000(mainfs) console=ttyS1,115200 mem=0x01f00000 vpe1_load_addr=0x81f00000 vpe1_mem=0x00100000 1 MIPSR2 register sets available Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH PID hash table entries: 128 (order: 7, 512 bytes) Using 166.667 MHz high precision timer. GPIO configuration for module 4 was not found. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 26476k/31744k available (2628k kernel code, 5268k reserved, 466k data, 164k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 Lantiq PCI host controller driver, version 1.1.5, (c) 2001-2010 Lantiq Deutschland GmbH SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered Registered CRAMFS in UBI MTD notifier gptu: totally 6 16-bit timers/counters gptu: misc_register on minor 63 gptu: succeeded to request irq 118 gptu: succeeded to request irq 119 gptu: succeeded to request irq 120 gptu: succeeded to request irq 121 gptu: succeeded to request irq 122 gptu: succeeded to request irq 123 IFX DMA driver, version ifxmips_dma_core.c:v1.0.7 ,(c)2009 Infineon Technologies AG Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH Wired TLB entries for Linux read_c0_wired() = 0 /proc/fs/cramfs_block_uncompressed created fuse init (API version 7.8) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered loop: loaded (max 8 devices) slram: not enough parameters. usbcore: registered new interface driver usblp /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial Driver core /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2 u32 classifier OLD policer on NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 21 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> GPIO configuration for module 3 was found. Lantiq SSC driver, version 2.1.5, (c) 2001-2010 Lantiq Deutschland GmbH IFX PPA API Directpath API loaded GPIO configuration for module 4 was not found. ttyS0 at MMIO map 0xbe100400 mem 0xbe100400 (irq = 98) is a IFX_ASC ttyS1 at MMIO map 0xbe100c00 mem 0xbe100c00 (irq = 105) is a IFX_ASC Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH Infineon Technologies DEU driver version 1.0.1 IFX DEU DES initialized (multiblock). IFX DEU AES initialized (multiblock). IFX DEU ARC4 initialized (multiblock). IFX DEU SHA1 initialized. IFX DEU MD5 initialized. IFX DEU SHA1_HMAC initialized. IFX DEU MD5_HMAC initialized. Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH IFX MEI Version 5.00.04ifx_nand_init Probe for NAND flash... NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks 3 cmdlinepart partitions found on MTD device ifx_nand Creating 3 MTD partitions on "ifx_nand": 0x00000000-0x00400000 : "rgloader" 0x00400000-0x02800000 : "UBI" 0x02800000-0x04000000 : "JFFS2" PMCU initiates! ifx_pmu_init: Major 253 Lantiq PMU driver, version 1.0.6, (c) 2001-2010 Lantiq Deutschland GmbH Loading A5 (MII0/1 + ATM) driver ...... <3>/home/bat/bat/vtech_netia_5_4_8_2/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_gpio.c:828:ifx_gpio_pin_reserve: Pin ID 32 (port 2, pin 0) has been reserved by module PPA from kernel! GPIO configuration for module 25 was not found. Succeeded! PPE datapath driver info: Version ID: 32.3.7.0.0.0.4 Family : AR9 DR Type : Normal Data Path | Indirect-Fast Path Interface : MII0 | MII1 | ATM Mode : N/A Release : 0.0.4 PPE firmware info: Version ID: 5.2.4.6.1.1 Family : AR9 FW Type : Acceleration Interface : MII0/1 + ATM Mode : Bridging + IPv4 Routing Release : 1.1 /home/bat/bat/vtech_netia_5_4_8_2/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16 GPIO configuration for module 20 was found. 1 cmdlinepart partitions found on MTD device ifx_sflash Creating 1 MTD partitions on "ifx_sflash": 0x00000000-0x00080000 : "sflash" Lantiq SPI flash driver, version 1.1.8, (c) 2001-2010 Lantiq Deutschland GmbH UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 16384 bytes (16 KiB) UBI: logical eraseblock size: 15872 bytes UBI: smallest flash I/O unit: 512 UBI: sub-page size: 256 UBI: VID header offset: 256 (aligned 256) UBI: data offset: 512 UBI: attached mtd1 to ubi0 UBI: MTD device name: "UBI" UBI: MTD device size: 36 MiB UBI: number of good PEBs: 2304 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 92 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 46 UBI: total number of reserved PEBs: 2258 UBI: number of PEBs reserved for bad PEB handling: 46 UBI: max/mean erase counter: 27/11 UBI: image sequence number: 22193626 1 cmdlinepart partitions found on MTD device NETIASPOT Creating 1 MTD partitions on "NETIASPOT": 0x001c5000-0x00715000 : "mainfs" mtd: partition "mainfs" doesn't start on an erase block boundary -- force read-only UBI: background thread "ubi_bgt0d" started, PID 15 Freeing unused kernel memory: 164k freed Found device mainfs on mtdblock5 Version: 5.4.8.2.45.1.8 Platform: Vtech ARX168 based Board Compilation Time: 24-Jan-12 17:38:18 Tag: Ntag-5_4_8_2_45_1_8 Compilation Flags: LIC=/home/bat/bat/vtech_netia_5_4_8_2/20120124_1628/conf/jpkg_mipseb_netia_arx.lic CONFIG_RG_PROD_IMG=y DIST=VTECH_ARX168_NETIA User Information: bat@rowlf /home/bat/bat/vtech_netia_5_4_8_2/dist insmod: add-symbol-file build/debug/rg_klog.o 0xc0012000 -s .data 0xc0012300 -s .bss 0xc00124a0 klog loaded insmod: add-symbol-file build/debug/rg_klog_ram_be.o 0xc000f000 -s .data 0xc0010880 -s .bss 0xc0010a20 klog: Using RAM buffer at address 0xa1ec0000 size 0x3fc00 klog: Invalid magic or checksum, reseting all information. Linux version 2.6.21.5 #1 Tue Jan 24 19:46:28 IST 2012 rofs_addr: 001c5000 (801c5000), len: 550000, flash_start_addr: 00000000 (80000000) flash_len: 0 CramFS in Flash rofs_start_addr: 00000000 len: 0 phym = 02000000, mem = 01f00000, max_pfn = 00001f00 Reserving memory for CP1 @0xa1f00000, size 0x00100000 CPU revision is: 0001954c Determined physical RAM map: User-defined physical RAM map: memory: 01f00000 @ 00000000 (usable) Reserved 256k KLOG memory starting from Physical 0x01ec0000 Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 7874 Kernel command line: cramfs=1 cramfs_offset=001c5000 mtdparts=ifx_nand:4M(rgloader),0x02400000(UBI),-(JFFS2);ifx_sflash:-(sflash);NETIASPOT:0x550000@0x001c5000(mainfs) console=ttyS1,115200 mem=0x01f00000 vpe1_load_addr=0x81f00000 vpe1_mem=0x00100000 1 MIPSR2 register sets available Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH PID hash table entries: 128 (order: 7, 512 bytes) Using 166.667 MHz high precision timer. GPIO configuration for module 4 was not found. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 26476k/31744k available (2628k kernel code, 5268k reserved, 466k data, 164k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 Lantiq PCI host controller driver, version 1.1.5, (c) 2001-2010 Lantiq Deutschland GmbH SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered Registered CRAMFS in UBI MTD notifier gptu: totally 6 16-bit timers/counters gptu: misc_register on minor 63 gptu: succeeded to request irq 118 gptu: succeeded to request irq 119 gptu: succeeded to request irq 120 gptu: succeeded to request irq 121 gptu: succeeded to request irq 122 gptu: succeeded to request irq 123 IFX DMA driver, version ifxmips_dma_core.c:v1.0.7 ,(c)2009 Infineon Technologies AG Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH Wired TLB entries for Linux read_c0_wired() = 0 /proc/fs/cramfs_block_uncompressed created fuse init (API version 7.8) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered loop: loaded (max 8 devices) slram: not enough parameters. usbcore: registered new interface driver usblp /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial Driver core /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option /home/bat/bat/vtech_netia_5_4_8_2/dist/os/linux-2.6/drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2 u32 classifier OLD policer on NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 21 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> GPIO configuration for module 3 was found. Lantiq SSC driver, version 2.1.5, (c) 2001-2010 Lantiq Deutschland GmbH IFX PPA API Directpath API loaded GPIO configuration for module 4 was not found. ttyS0 at MMIO map 0xbe100400 mem 0xbe100400 (irq = 98) is a IFX_ASC ttyS1 at MMIO map 0xbe100c00 mem 0xbe100c00 (irq = 105) is a IFX_ASC Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH Infineon Technologies DEU driver version 1.0.1 IFX DEU DES initialized (multiblock). IFX DEU AES initialized (multiblock). IFX DEU ARC4 initialized (multiblock). IFX DEU SHA1 initialized. IFX DEU MD5 initialized. IFX DEU SHA1_HMAC initialized. IFX DEU MD5_HMAC initialized. Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH IFX MEI Version 5.00.04ifx_nand_init Probe for NAND flash... NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks 3 cmdlinepart partitions found on MTD device ifx_nand Creating 3 MTD partitions on "ifx_nand": 0x00000000-0x00400000 : "rgloader" 0x00400000-0x02800000 : "UBI" 0x02800000-0x04000000 : "JFFS2" PMCU initiates! ifx_pmu_init: Major 253 Lantiq PMU driver, version 1.0.6, (c) 2001-2010 Lantiq Deutschland GmbH Loading A5 (MII0/1 + ATM) driver ...... <3>/home/bat/bat/vtech_netia_5_4_8_2/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_gpio.c:828:ifx_gpio_pin_reserve: Pin ID 32 (port 2, pin 0) has been reserved by module PPA from kernel! GPIO configuration for module 25 was not found. Succeeded! PPE datapath driver info: Version ID: 32.3.7.0.0.0.4 Family : AR9 DR Type : Normal Data Path | Indirect-Fast Path Interface : MII0 | MII1 | ATM Mode : N/A Release : 0.0.4 PPE firmware info: Version ID: 5.2.4.6.1.1 Family : AR9 FW Type : Acceleration Interface : MII0/1 + ATM Mode : Bridging + IPv4 Routing Release : 1.1 /home/bat/bat/vtech_netia_5_4_8_2/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16 GPIO configuration for module 20 was found. 1 cmdlinepart partitions found on MTD device ifx_sflash Creating 1 MTD partitions on "ifx_sflash": 0x00000000-0x00080000 : "sflash" Lantiq SPI flash driver, version 1.1.8, (c) 2001-2010 Lantiq Deutschland GmbH UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 16384 bytes (16 KiB) UBI: logical eraseblock size: 15872 bytes UBI: smallest flash I/O unit: 512 UBI: sub-page size: 256 UBI: VID header offset: 256 (aligned 256) UBI: data offset: 512 UBI: attached mtd1 to ubi0 UBI: MTD device name: "UBI" UBI: MTD device size: 36 MiB UBI: number of good PEBs: 2304 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 92 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 46 UBI: total number of reserved PEBs: 2258 UBI: number of PEBs reserved for bad PEB handling: 46 UBI: max/mean erase counter: 27/11 UBI: image sequence number: 22193626 1 cmdlinepart partitions found on MTD device NETIASPOT Creating 1 MTD partitions on "NETIASPOT": 0x001c5000-0x00715000 : "mainfs" mtd: partition "mainfs" doesn't start on an erase block boundary -- force read-only UBI: background thread "ubi_bgt0d" started, PID 15 Freeing unused kernel memory: 164k freed Found device mainfs on mtdblock5 Algorithmics/MIPS FPU Emulator v1.5 insmod: add-symbol-file build/debug/rg_klog.o 0xc0012000 -s .data 0xc0012300 -s .bss 0xc00124a0 klog loaded insmod: add-symbol-file build/debug/rg_klog_ram_be.o 0xc000f000 -s .data 0xc0010880 -s .bss 0xc0010a20 klog: Using RAM buffer at address 0xa1ec0000 size 0x3fc00 klog: Invalid magic or checksum, reseting all information. klog initialization succeeded klog RAM store initialization succeeded. insmod: add-symbol-file build/debug/be_pppoa_mod.o 0xc0017000 -s .data 0xc0017cd0 -s .bss 0xc0017e40 insmod: add-symbol-file build/debug/be_pppos_mod.o 0xc0014000 -s .data 0xc0015b60 -s .bss 0xc0015d20 insmod: add-symbol-file build/debug/one_module.o 0xc00a6000 -s .main_flow 0xc00e8110 -s .data 0xc00f6540 -s .bss 0xc00f86e0 Loading license 12756d10c06ed9596404655b9295885c58b586796110f5772709751af73b96dd4363148a1e545bc0c793ad2a71ab865348b091bddb0490a7dac3cae35cac233c97bc9411a9dbdeef797d980542cc480921de41b32a03c8e3a9d9c6d410afa0c584c54b5683b748655958.ARX168_FOR_NETIA loading license key: ARX168_FOR_NETIA loading license key: ARX168_FOR_NETIA insmod: add-symbol-file build/debug/jffs2.o 0xc0042000 -s .data 0xc005cb20 -s .bss 0xc005ccc0 JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. insmod: add-symbol-file build/debug/igmp_proxy_mod.o 0xc0020000 -s .data 0xc0022a40 -s .bss 0xc0022be0 insmod: add-symbol-file build/debug/kleds_mod.o 0xc001c000 -s .data 0xc001c910 -s .bss 0xc001cac0 insmod: add-symbol-file build/debug/wave300.o 0xc0225000 -s .data 0xc02b5ef0 -s .bss 0xc02b6e60 [4294676756] mtlk0 (mtlk_cdev_init:265): Max nodex set to 1048575 [4294676756] mtlk0 (mtlk_fast_mem_print_info:103): Using normal memory for hot context [4294676766] mtlk0(mtlk_vap_manager_create_vap:186): available vap_index 0 [4294677226] mtlk0(mtlk_core_start:7811): Driver version: 3.2.0.71.Jungo.0.1.PciG3.Release MAC/PHY versions: ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r4248 MIPS: Upper CPU(TMC AGG AP) interface: PCI phy type: real phy on Nov 3 2011 at 15:42:22@@@ END @@@ contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r4248 MIPS: Lower MAC interface: -- phy type: real phy on Nov 3 2011 at 15:42:20@@@ END @@@ [4294678336] mtlk0(mtlk_eeprom_check_ee_data:2074): Options mask is 0x00 [4294678336] mtlk0(load_default_hw_table:1805): HW configuration is 2X2 [4294678346] mtlk0(mtlk_df_user_start:5577): NDEV Name pattern: wlan%d Press ESC to enter BOOT MENU mode. MAPS: 00400000-00774000 r-xp 00000000 1f:05 737140 /mnt/cramfs/bin/openrg 007b4000-0083d000 rw-p 00374000 1f:05 737140 /mnt/cramfs/bin/openrg 0083d000-00a7c0 insmod: add-symbol-file build/debug/rg_klog_chardev.o 0xc001e000 -s .data 0xc001e3a0 -s .bss 0xc001e540 00 rwxpklog chardev initialized. 0083d000 00:00 0 [heap] 2aaa8000-2aaae000 r-xp 00000000 1f:05 4469488 /mnt/cramfs/lib insmod: add-symbol-file build/debug/log_chardev.o 0xc0025000 -s .data 0xc0025730 -s .bss 0xc00258c0 /ld-uClibc.so.0 2aaae000-2aaaf000 rw-p 2aaae000 00:00 0 2aaed000-2aaee000 r--p 00005000 1f:05 4469488 /mnt/cramfs/lib/ld-uClibc.so.0 2aaee000-2aaef000 rw-p 00006000 1f:05 4469488 insmod: add-symbol-file build/debug/rg_usfs.o 0xc0019000 -s .data 0xc0019ea0 -s .bss 0xc001a040 /mnt/cramfs/lib/ld-uClibc.so.0 2aaef000-2ab00000 r-xp 00000000 1f:05 5187364 /mnt/cramfs/lib/libopenrg.so 2ab00000-2ab40000 ---p 2ab00000 00:00 0 2ab40000-2ab41000 rw-p 00011000 1f:05 5187364 insmod: add-symbol-file build/debug/tcp_mss.o 0xc002a000 -s .data 0xc002a590 -s .bss 0xc002a720 /mnt/cramfs/lib/libopenrg.so 2ab41000-2ab87000 r-xp 00000000 1f:05 4973820 /mnt/cramfs/lib/libjutil.so 2ab87000- insmod: add-symbol-file build/debug/rg_ipv4.o 0xc002c000 -s .data 0xc002c1f0 -s .bss 0xc002c380 2abc600IPV4 device driver registered 0 ---p 2ab87000 00:00 0 2abc6000-2abcd000 rw-p 00045000 1f:05 4973820 /mnt/cramfs/lib/libjutil.so 2abcd000-2abd40 insmod: add-symbol-file build/debug/btn.o 0xc002e000 -s .data 0xc002e820 -s .bss 0xc002e9c0 00 rw-p 2abcd000 00:00 0 2abd4000-2ac0c000 r-xp 00000000 1f:05 5359540 /mnt/cramfs/liGPIO configuration for module 29 was not found. b/libssl.so 2ac0c000-2ac4b000 ---p 2ac0c000 00:00 0 2ac4b000-2ac4f000 rw-p 00037000 1f:05 5359540 /mnt/cramfs/lib/l insmod: add-symbol-file build/debug/qos_ingress.o 0xc0030000 -s .data 0xc0030a60 -s .bss 0xc0030c00 ibssl.so 2ac4f000-2ad49000 r-xp 00000000 1f:05 4622492 /mnt/cramfs/lib/libcrypto.so 2ad49000-2ad88000 ---p 2ad49000 00:00 0 2ad88000-2ad9b000 rw-p 000f9000 1f:05 4622492 /mnt/cramfs/lib/libcrypto.so 2ad9b000-2ad9e000 rw-p 2ad9b000 00:00 0 2ad9e000-2ada0000 r-xp 00000000 1f:05 4945192 /mnt/cramfs/lib/libdl.so.0 2ada0000-2addf000 ---p 2ada0000 00:00 0 2addf000-2ade0000 r--p 00001000 1f:05 4945192 /mnt/cramfs/lib/libdl.so.0 2ade0000-2ade1000 rw-p 00002000 1f:05 4945192 /mnt/cramfs/lib/libdl.so.0 2ade1000-2adf9000 r-xp 00000000 1f:05 5240920 /mnt/cramfs/lib/librg_config.so 2adf9000-2ae39000 ---p 2adf9000 00:00 0 2ae39000-2ae3c000 rw-p 00018000 1f:05 5240920 /mnt/cramfs/lib/librg_config.so 2ae3c000-2ae4b000 r-xp 00000000 1f:05 5069056 /mnt/cramfs/lib/libm.so.0 2ae4b000-2ae8b000 ---p 2ae4b000 00:00 0 2ae8b000-2ae8c000 rw-p 0000f000 1f:05 5069056 /mnt/cramfs/lib/libm.so.0 2ae8c000-2ae8d000 r-xp 00000000 1f:05 5481680 /mnt/cramfs/lib/libutil.so.0 2ae8d000-2aecd000 ---p 2ae8d000 00:00 0 2aecd000-2aece000 rw-p 00001000 1f:05 5481680 /mnt/cramfs/lib/libutil.so.0 2aece000-2af36000 r-xp 00000000 1f:05 4478492 /mnt/cramfs/lib/libc.so.0 2af36000-2af75000 ---p 2af36000 00:00 0 2af75000-2af76000 r--p 00067000 1f:05 4478492 /mnt/cramfs/lib/libc. insmod: add-symbol-file build/debug/ifxusb_driver_mod.o 0xc0081000 -s .data 0xc00940c0 -s .bss 0xc0094860 so.0 2af76000-2af78000 rw-p 00068000 1f:05 4478492 /mnt/cramfs/lib/libc.so.0 2af78000-2af7c000 rIFXUSB: ifxusb_hcd: version 3.0 B101005 w-p 2af78000 00:00 0 7fb5d000-7fb72000 rwxp 7fb5d000 00:00 0 [stack] IFXUSB: USB core #0 soft-reset IFXUSB: USB core #0 soft-reset ifxusb_hcd ifxusb_hcd: IFX USB Controller ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1 ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000 GPIO configuration for module 7 was found. IFXUSB: Init: Power Port (0) registering (overcurrent) handler for irq 158 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected IFXUSB: USB core #1 soft-reset IFXUSB: USB core #1 soft-reset ifxusb_hcd ifxusb_hcd: IFX USB Controller ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2 ifxusb_hcd ifxusb_hcd: irq 83, io mem 0xbe106000 IFXUSB: Init: Power Port (0) usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected insmod: add-symbol-file build/debug/drv_dsl_cpe_api_mod.o 0xc0192000 -s .data 0xc01cd6c0 -s .bss 0xc01ce4c0 Lantiq CPE API Driver version: DSL CPE API V4.2.0 Predefined debug level: 3 insmod: add-symbol-file build/debug/psb6973_mod.o 0xc0037000 -s .data 0xc0038ff0 -s .bss 0xc0039280 Freeing CRAMFS/MODFS: 768k freed userspace registering PID [4294693376] mtlk0(_mtlk_core_mbss_add_vap:5343): Got PRM_ID_VAP_ADD [4294693376] mtlk0(mtlk_vap_manager_create_vap:186): available vap_index 1 [4294693386] mtlk0(mtlk_core_start:7811): Driver version: 3.2.0.71.Jungo.0.1.PciG3.Release MAC/PHY versions: ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r4248 MIPS: Upper CPU(TMC AGG AP) interface: PCI phy type: real phy on Nov 3 2011 at 15:42:22@@@ END @@@ contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r4248 MIPS: Lower MAC interface: -- phy type: real phy on Nov 3 2011 at 15:42:20@@@ END @@@ [4294693396] mtlk0(mtlk_df_user_start:5577): NDEV Name pattern: wlan0.%d [4294693396] mtlk0(_mtlk_core_mbss_add_vap:5354): VAP#1 added [4294693416] mtlk0(_mtlk_core_mbss_add_vap:5343): Got PRM_ID_VAP_ADD [4294693416] mtlk0(mtlk_vap_manager_create_vap:186): available vap_index 2 [4294693426] mtlk0(mtlk_core_start:7811): Driver version: 3.2.0.71.Jungo.0.1.PciG3.Release MAC/PHY versions: ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r4248 MIPS: Upper CPU(TMC AGG AP) interface: PCI phy type: real phy on Nov 3 2011 at 15:42:22@@@ END @@@ contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r4248 MIPS: Lower MAC interface: -- phy type: real phy on Nov 3 2011 at 15:42:20@@@ END @@@ [4294693436] mtlk0(mtlk_df_user_start:5577): NDEV Name pattern: wlan0.%d [4294693436] mtlk0(_mtlk_core_mbss_add_vap:5354): VAP#2 added Modem is not ready!eth0_main: MAC Address: xx:xx:xx:xx:xx:xx device eth0_main entered promiscuous mode eth2: MAC Address: xx:xx:xx:xx:xx:xx [4294695026] mtlk<4>(mtlk_core_update_network_mode:5972): 20MHz spectrum forced for 802.11bg [4294695046] mtlk0(_mtlk_mbss_send_preactivate:2184): bonding = 0 [4294695056] mtlk0(_mtlk_mbss_send_preactivate:2190): mtlk_aocs_set_spectrum_mode with 0 [4294695056] mtlk0(_mtlk_mbss_send_preactivate:2195): mtlk_aocs_set_config_is_ht with 0 [4294695066] mtlk0(_mtlk_mbss_send_preactivate:2198): mtlk_aocs_set_config_frequency_band with 1 [4294695076] mtlk0(_mtlk_mbss_send_preactivate:2203): mtlk_aocs_start [4294695086] mtlk0(_mtlk_mbss_send_preactivate:2215): ap_scan_band_cfg = 1 [4294695086] mtlk0(_mtlk_core_perform_initial_scan:2061): AOCS is ON (ch=0 type=0): doing the Initial Scan [4294695096] mtlk0(_mtlk_core_perform_initial_scan:2072): Initial scan started SPECTRUM_20MHZ [4294697806] mtlk<4>(mtlk_aocs_indicate_event:3832): Cannot auto select channel because HT is off: forcing 20MHz selection [4294697816] mtlk0(_mtlk_mbss_send_preactivate:2303): mtlk_txmm_msg_send_blocked, MsgId = 0x451 [4294698006] mtlk0(_mtlk_mbss_send_preactivate:2322): _mtlk_mbss_send_preactivate returned successfully [4294698016] mtlk0(mtlk_mbss_init:2674): _mtlk_mbss_send_preactivate_if_needed returned successfully [4294698026] mtlk0(mtlk_mbss_send_vap_activate:2385): Entering mtlk_mbss_send_vap_activate [4294698036] mtlk0(mtlk_mbss_send_vap_activate:2392): wlan0 [4294698036] mtlk0(mtlk_mbss_send_vap_activate:2440): UMI_ACTIVATE_VAP (wlan0) [4294698046] mtlk0(mtlk_mbss_send_vap_activate:2441): sBSSID = xx:xx:xx:xx:xx:xx [4294698046] mtlk0(mtlk_mbss_send_vap_activate:2442): sSSID = NETIASPOT-xxxxxx [4294698056] mtlk0(mtlk_mbss_send_vap_activate:2443): Hidden = 0 [4294698066] mtlk0 (mtlk_mbss_send_vap_activate:2444): sRSNie = cp= 0x804c093a l=80 0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [4294698096] mtlk0(mtlk_mbss_send_vap_activate:2446): mtlk_txmm_msg_send, MsgId = 0x453, ESSID = NETIASPOT-xxxxxx [4294698106] mtlk0(mtlk_mbss_init:2681): mtlk_mbss_send_vap_activate returned successfully [4294698116] mtlk0(_mtlk_handle_algo_failure:8168): MAC event: Online calibration scheduler: algo type 1, state 4096, wlan0 [4294698126] mtlk0(_mtlk_handle_algo_failure:8168): MAC event: Online calibration scheduler: algo type 4, state 4096, wlan0 device wlan0 entered promiscuous mode [4294700196] mtlk0(_mtlk_mbss_send_preactivate:2184): bonding = 0 [4294700196] mtlk0(_mtlk_mbss_send_preactivate:2190): mtlk_aocs_set_spectrum_mode with 0 [4294700206] mtlk0(_mtlk_mbss_send_preactivate:2195): mtlk_aocs_set_config_is_ht with 0 [4294700216] mtlk0(_mtlk_mbss_send_preactivate:2198): mtlk_aocs_set_config_frequency_band with 1 [4294700216] mtlk0(_mtlk_mbss_send_preactivate:2203): mtlk_aocs_start [4294700226] mtlk0(_mtlk_mbss_send_preactivate:2215): ap_scan_band_cfg = 1 [4294700236] mtlk0(_mtlk_core_perform_initial_scan:2080): AOCS is completely OFF (ch=11 type=0): skipping the Initial Scan [4294700246] mtlk<4>(mtlk_aocs_indicate_event:3832): Cannot auto select channel because HT is off: forcing 20MHz selection [4294700286] mtlk0(_mtlk_mbss_send_preactivate:2303): mtlk_txmm_msg_send_blocked, MsgId = 0x451 [4294700476] mtlk0(_mtlk_mbss_send_preactivate:2322): _mtlk_mbss_send_preactivate returned successfully [4294700486] mtlk0(mtlk_mbss_init:2674): _mtlk_mbss_send_preactivate_if_needed returned successfully [4294700496] mtlk0(mtlk_mbss_send_vap_activate:2385): Entering mtlk_mbss_send_vap_activate [4294700496] mtlk0(mtlk_mbss_send_vap_activate:2392): wlan0 [4294700506] mtlk0(mtlk_mbss_send_vap_activate:2440): UMI_ACTIVATE_VAP (wlan0) [4294700516] mtlk0(mtlk_mbss_send_vap_activate:2441): sBSSID = xx:xx:xx:xx:xx:xx [4294700516] mtlk0(mtlk_mbss_send_vap_activate:2442): sSSID = NETIASPOT-xxxxxx [4294700526] mtlk0(mtlk_mbss_send_vap_activate:2443): Hidden = 0 [4294700536] mtlk0 (mtlk_mbss_send_vap_activate:2444): sRSNie = cp= 0x804c0da2 l=80 0000: 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 0010: 00 0f ac 02 00 00 00 00 00 00 00 00 00 00 00 00 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [4294700566] mtlk0(mtlk_mbss_send_vap_activate:2446): mtlk_txmm_msg_send, MsgId = 0x453, ESSID = NETIASPOT-xxxxxx [4294700576] mtlk0(mtlk_mbss_init:2681): mtlk_mbss_send_vap_activate returned successfully Username:


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2019/10/17 11:54
  • by tmomas