Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:vtech:iad505 [2021/06/04 01:30] – [Hardware] Fixing erronous WiFi information moriel5toh:vtech:iad505 [2021/06/04 02:28] – [Info] Added Ethernet PHY information moriel5
Line 11: Line 11:
  
 ^ CPU ^ Ram ^ Flash ^ Switch ^ Ethernet ^ WLAN Hardware ^ WLAN ^ USB ^ Modem ^ SLIC ^ POTS ^ Serial ^ JTag ^ ^ CPU ^ Ram ^ Flash ^ Switch ^ Ethernet ^ WLAN Hardware ^ WLAN ^ USB ^ Modem ^ SLIC ^ POTS ^ Serial ^ JTag ^
-| Lantiq XWAY VRX200 | 128MB | 64MB | Lantiq PHY11G | 4 x 100Mbts | Lantiq XWAY300 x 2*| a/b/g/n + a/n | 2 x 3.0 | Lantiq XWAY VRX208 | Lantiq XWAY SLIC120 | 2 x RJ11 |  Yes  | |+| Lantiq XWAY VRX200 | 128MB | 64MB | Lantiq PHY11G | 4 x 100Mbts | Lantiq XWAY300 x 2*| abgn | 2 x 3.0 | Lantiq XWAY VRX208 | Lantiq XWAY SLIC120 | 2x FXS  |  Yes  | |
 *1 x 2.4Ghz + 1 + 5Ghz *1 x 2.4Ghz + 1 + 5Ghz
 ==== Info ==== ==== Info ====
-Serial on the top middle, pins are as marked in the left photo, highlighted in red ( ignore soldered on pin headers ). 
-Serial Baud rate is 115200, 8 data bits, 1 stop bit and no parity. 
-Flow control is RTS/CTS. 
- 
 ^ [[wp>Instruction set|Architecture]]    | [[wp>MIPS architecture|MIPS]] | ^ [[wp>Instruction set|Architecture]]    | [[wp>MIPS architecture|MIPS]] |
 ^ Vendor          | [[wp>Lantiq]] | ^ Vendor          | [[wp>Lantiq]] |
 ^ [[docs:techref:bootloader]]     | [[docs:techref:bootloader:uboot|U-Boot]] | ^ [[docs:techref:bootloader]]     | [[docs:techref:bootloader:uboot|U-Boot]] |
-^ [[docs:techref:hardware:soc|System-On-Chip]]  | [[docs:techref:hardware:soc:soc.lantiq|Lantiq XWAY 2??]] |+^ [[docs:techref:hardware:soc|System-On-Chip]]  | [[docs:techref:hardware:soc:soc.lantiq|Lantiq XWAY VRX200]] |
 ^ [[docs:techref:hardware:cpu|CPU]]/Speed        | 34KEc, 500MHz(?) | ^ [[docs:techref:hardware:cpu|CPU]]/Speed        | 34KEc, 500MHz(?) |
-^ Flash-Chip      | [[http://datasheet.elcodis.com/pdf2/103/58/1035811/tc58dvm92a5ta00.pdf|Toshiba X19(TC58DVM92A00(?)*)]] |+^ Flash-Chip      | [[http://datasheet.elcodis.com/pdf2/103/58/1035811/tc58dvm92a5ta00.pdf|Toshiba X8319(TC58DVM92A00(?)*]] |
 ^ Flash size      | 64 MiB | ^ Flash size      | 64 MiB |
 +^ Flash type      | E2PROM |
 ^ RAM-Chip        | EtronTech EM68C16CWVB-25H | ^ RAM-Chip        | EtronTech EM68C16CWVB-25H |
-^ RAM             | 128 MiB | +^ RAM/Speed       | DDR2, 800Mhz(?) | 
-^ Wireless        | Lantiq XWAY300 (PSB 8221 EL/PSB 8231 EL) | +^ RAM size        | 128 MiB | 
-^ Wireless PHYs   | 2.4ghz + 5Ghz 802.11abgn 3T3R PCI/PCIe | +^ Wireless        | Lantiq XWAY300 (PSB 8221 EL v1.1 + PSB 8231 EL v1.1) | 
-^ SLIC            | Lantiq SLIC120 (PEF 42068 V) | +^ Wireless PHYs   | 2.4ghz + 5Ghz 802.11abgn 3T3R PCI PCIe | 
-^ POTS            | 2x FXS, 1xFXO +^ SLIC   | [[https://www.electronicsdatasheets.com/pdfjs/?file=/download/51c42036e34e246e490000b4.pdf?format=pdf|Lantiq SLIC120 (PEF 42068 V v1.2)]] 
-^ Ethernet        | [[https://www.maxlinear.com/ds/gpy111_pef7071vv16_um_hd_rev1.4.pdf|Lantiq PHY11G]] |+^ POTS            | 2x FXS | 
 +^ Ethernet        | [[https://datasheet.octopart.com/PEF-7071-V-V1.5-Lantiq-datasheet-62314344.pdf|Lantiq PHY11G (PEF7071 V v1.5)]] | 
 +^ Ethernet PHYs   | 4 x 100Mbt | 
 +^ Modem           | [[https://datasheet.datasheetarchive.com/originals/library/Datasheets-EDS4/DSAEDA00066872.pdf|Lantiq XWAY VRX208 (PSB 80190 V v1.1)]] |
 ^ Internet        | VDSL2 | ^ Internet        | VDSL2 |
 ^ USB             | Yes, 2 x USB3.0 | ^ USB             | Yes, 2 x USB3.0 |
Line 38: Line 38:
  
 *moriel5: The exact model is obscured by a label that is adhered to the IC on my unit, so basing this upon existing picture. *moriel5: The exact model is obscured by a label that is adhered to the IC on my unit, so basing this upon existing picture.
 +
 +Serial on the top middle, pins are as marked in the left photo, highlighted in red ( ignore soldered on pin headers ).
 +Serial Baud rate is 115200, 8 data bits, 1 stop bit and no parity.
 +Flow control is RTS/CTS.
  
 UBoot requires a password. UBoot requires a password.
  • Last modified: 2021/10/27 19:05
  • by moriel5