Vonets MINI300
The Vonets MINI300 is a miniature router based on the MediaTek MT7620n with one Ethernet port and a 802.11n 2T/2R 2.4 GHz 300Mbps wireless interface.
OpenWrt support
Not supported.
Hardware
Info
| Architecture | MIPS 24KEc V5.0 (ramips) |
|---|---|
| Vendor | MediaTek |
| System-On-Chip | MediaTek MT7620n |
| CPU Speed | 580MHz |
| RAM memory | 32 MB SDRAM, W9825G6PH-6 / W9825G6EH-6 |
| Flash chip | 4 MB, Pm25LQ032 |
| Wired network | 1 x Ethernet 10/100 Mbps |
| Ethernet chip | MediaTek MT7530 (SoC) |
| Ethernet switch | MediaTek MT7530 (integrated) |
| Wireless network | 2.4 GHz 802.11n MiMo 2×2:2 |
| Wireless chip | MediaTek RT5390 (SoC) |
| Wireless antennas | 2 x printed on-board |
| USB | Micro USB (power only) |
| Serial port | Yes (TTL pins) |
| Physical size | 43mm x 43mm x 14mm |
Serial connection
The serial port of the MINI300 can be accessed using the TTL pins shown in the image below. A voltage level converter (such as a CP2102 TTL-USB dongle) is required.
Internal board with serial interface soldered:
The communication settings are: 57600 - 8N1.
Identifying the device
On the Vonets MINI300, the Ethernet MAC starts with 00:17:13 (Tiger NetCom).
GPIO
| GPIO | |
| 38 | Blue LED |
| 40 | Green LED |
Original firmware telnet login
Original firmware
Software information
# cat /proc/cpuinfo system type : Ralink SoC processor : 0 cpu model : MIPS 24Kc V5.0 BogoMIPS : 386.04 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0098, 0x0ffb, 0x0ff8] ASEs implemented : mips16 dsp shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available
# cat /proc/mounts rootfs / rootfs rw 0 0 proc /proc proc rw,relatime 0 0 none /var ramfs rw,relatime 0 0 none /etc ramfs rw,relatime 0 0 none /tmp ramfs rw,relatime 0 0 none /media ramfs rw,relatime 0 0 none /sys sysfs rw,relatime 0 0 none /dev/pts devpts rw,relatime,mode=600 0 0 none /proc/bus/usb usbfs rw,relatime 0 0 mdev /dev ramfs rw,relatime 0 0 devpts /dev/pts devpts rw,relatime,mode=600 0 0
# cat /proc/mtd dev: size erasesize name mtd0: 00400000 00010000 "ALL" mtd1: 00030000 00010000 "Bootloader" mtd2: 00010000 00010000 "Config" mtd3: 00010000 00010000 "Factory" mtd4: 003b0000 00010000 "Kernel"
# cat /proc/partitions major minor #blocks name 31 0 4096 mtdblock0 31 1 192 mtdblock1 31 2 64 mtdblock2 31 3 64 mtdblock3 31 4 3776 mtdblock4
# cat /proc/iomem 00000000-01ffffff : System RAM 00000000-003c6127 : Kernel code 003c6128-004879ff : Kernel data 101c0000-101c0fff : rt3xxx-ehci 101c1000-101c1fff : rt3xxx-ohci
# cat /proc/cmdline console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
# cat /proc/version Linux version 2.6.36 (root@ht) (gcc version 3.4.2) #1 Mon Oct 12 01:55:38 CST 2015
# cat /proc/crypto name : ecb(arc4) driver : ecb(arc4-generic) module : kernel priority : 0 refcnt : 1 selftest : passed type : blkcipher blocksize : 1 min keysize : 1 max keysize : 256 ivsize : 0 geniv : <default> name : stdrng driver : krng module : kernel priority : 200 refcnt : 1 selftest : passed type : rng seedsize : 0 name : arc4 driver : arc4-generic module : kernel priority : 0 refcnt : 1 selftest : passed type : cipher blocksize : 1 min keysize : 1 max keysize : 256 name : sha1 driver : sha1-generic module : kernel priority : 0 refcnt : 1 selftest : passed type : shash blocksize : 64 digestsize : 20
# ifconfig
apcli0 Link encap:Ethernet HWaddr 00:17:13:xx:xx:xx
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br0 Link encap:Ethernet HWaddr 00:17:13:xx:xx:xx
inet addr:192.168.254.254 Bcast:192.168.254.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:298 errors:0 dropped:0 overruns:0 frame:0
TX packets:217 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth2 Link encap:Ethernet HWaddr 00:17:13:xx:xx:xx
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:298 errors:0 dropped:0 overruns:0 frame:0
TX packets:217 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:3
eth2.1 Link encap:Ethernet HWaddr 00:17:13:xx:xx:xx
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ra0 Link encap:Ethernet HWaddr 00:17:13:xx:xx:xx
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:4
# brctl show
bridge name bridge id STP enabled interfaces
br0 8000.001713xxxxxx no ra0
apcli0
eth2
Bootlogs
U-boot bootlog
U-Boot 1.1.3 (May 26 2014 - 14:52:34) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb8000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 42 spi device id: 7f 9d 46 7f 9d (9d467f9d) Warning: un-recognized chip ID, please update bootloader! raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.2.S.1 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: SPI Flash Date:May 26 2014 Time:14:52:34 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 600 MHZ #### estimate memory size =32 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3166448 Bytes = 3 MB Load Address: 80000000 Entry Point: 8000c2f0 raspi_read: from:50040 len:3050f0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c2f0) ... ## Giving linux memsize in MB, 32 Starting kernel ...
Firmware bootlog
Linux version 2.6.36 (root@ht) (gcc version 3.4.2) #1 Mon Oct 12 01:55:38 CST 2015 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe PCIE: PLL power down for MT7620N CPU revision is: 00019650 (MIPS 24Kc) Software DMA cache coherency Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00002000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00002000 On node 0 totalpages: 8192 free_area_init_node: node 0, pgdat 80487380, node_mem_map 81000000 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8128 pages, LIFO batch:0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 PID hash table entries: 128 (order: -3, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0000000c Readback ErrCtl register=0000000c Memory: 18280k/32768k available (3864k kernel code, 14488k reserved, 774k data, 9280k init, 0k highmem) NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RT3xxx EHCI/OHCI init. fuse init (API version 7.15) msgmni has been set to 35 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) HDLC line discipline maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : 7f 9d 46 7f 9d (9d467f9d) Warning: un-recognized chip ID, please update SPI driver! AT25DF321(1f 47000000) (4096 Kbytes) mtd .name = raspi, .size = 0x00400000 (0M) .erasesize = 0x00000004 (0K) .numeraseregions = 65536 Creating 5 MTD partitions on "raspi": 0x000000000000-0x000000400000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000001000000 : "Kernel" mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x3b0000 rdm_major = 253 SMACCR1 -- : 0x00000017 SMACCR0 -- : 0x131b2f4a Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! SMACCR1 -- : 0x00000017 SMACCR0 -- : 0x131b2f4a PROC INIT OK! PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). CSLIP: code copyright 1989 Regents of the University of California. usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus === pAd = c0003000, size = 828616 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.2.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial usbserial: USB Serial Driver core USB Serial support registered for opticon usbcore: registered new interface driver opticon nf_conntrack version 0.5.0 (285 buckets, 1140 max) IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Freeing unused kernel memory: 9280k freed Algorithmics/MIPS FPU Emulator v1.5 devpts: called with bogus options ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected RX DESC a0ec8000 size = 2048 RTMP_TimerListAdd: add timer obj c009cb40! RTMP_TimerListAdd: add timer obj c0067ac4! RTMP_TimerListAdd: add timer obj c0067a98! RTMP_TimerListAdd: add timer obj c0067af0! RTMP_TimerListAdd: add timer obj c0067a6c! RTMP_TimerListAdd: add timer obj c000b41c! RTMP_TimerListAdd: add timer obj c000ac64! RTMP_TimerListAdd: add timer obj c000b3ec! RTMP_TimerListAdd: add timer obj c000b794! RTMP_TimerListAdd: add timer obj c000b4e4! RTMP_TimerListAdd: add timer obj c000b514! RTMP_TimerListAdd: add timer obj c000b6d4! RTMP_TimerListAdd: add timer obj c000b704! RTMP_TimerListAdd: add timer obj c006a2ec! RTMP_TimerListAdd: add timer obj c0069b34! RTMP_TimerListAdd: add timer obj c006a2bc! RTMP_TimerListAdd: add timer obj c006a664! RTMP_TimerListAdd: add timer obj c006a3b4! RTMP_TimerListAdd: add timer obj c006a3e4! RTMP_TimerListAdd: add timer obj c006a31c! RTMP_TimerListAdd: add timer obj c006a34c! RTMP_TimerListAdd: add timer obj c006a37c! RTMP_TimerListAdd: add timer obj c00734ac! RTMP_TimerListAdd: add timer obj c00735c8! RTMP_TimerListAdd: add timer obj c00734d8! RTMP_TimerListAdd: add timer obj c006aa54! RTMP_TimerListAdd: add timer obj c0008530! RTMP_TimerListAdd: add timer obj c006a75c! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) ff:ac:f2:bb:9b:14:da:b7:6a:22:24:9a:52:dd:14:cc: 23:90:a1:e1:8d:70:11:e5:8d:5b:16:cf:e7:e0:ef:2b: 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 RTMP_TimerListAdd: add timer obj c000812c! AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -3, D2 = 3, CalCode = 14 !!! RT6352_Temperature_Init : BBPR49 = 0xfffffffd RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff3 Current Temperature from BBP_R49=0xfffffffb TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= 1, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 0, phase=3e) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 RTMP_TimerListAdd: add timer obj c006ad34! Main bssid = 00:17:13:xx:xx:xx <==== rt28xx_init, Status=0 0x1300 = 00064380 rt3xxx-ehci rt3xxx-ehci: remove, state 1 usb usb1: USB disconnect, address 1 rt3xxx-ehci rt3xxx-ehci: USB bus 1 deregistered rt3xxx-ohci rt3xxx-ohci: remove, state 1 usb usb2: USB disconnect, address 1 rt3xxx-ohci rt3xxx-ohci: USB bus 2 deregistered RX DESC a0ec8000 size = 2048 RTMP_TimerListAdd: add timer obj c009cb40! RTMP_TimerListAdd: add timer obj c0067ac4! RTMP_TimerListAdd: add timer obj c0067a98! RTMP_TimerListAdd: add timer obj c0067af0! RTMP_TimerListAdd: add timer obj c0067a6c! RTMP_TimerListAdd: add timer obj c000b41c! RTMP_TimerListAdd: add timer obj c000ac64! RTMP_TimerListAdd: add timer obj c000b3ec! RTMP_TimerListAdd: add timer obj c000b794! RTMP_TimerListAdd: add timer obj c000b4e4! RTMP_TimerListAdd: add timer obj c000b514! RTMP_TimerListAdd: add timer obj c000b6d4! RTMP_TimerListAdd: add timer obj c000b704! RTMP_TimerListAdd: add timer obj c006a2ec! RTMP_TimerListAdd: add timer obj c0069b34! RTMP_TimerListAdd: add timer obj c006a2bc! RTMP_TimerListAdd: add timer obj c006a664! RTMP_TimerListAdd: add timer obj c006a3b4! RTMP_TimerListAdd: add timer obj c006a3e4! RTMP_TimerListAdd: add timer obj c006a31c! RTMP_TimerListAdd: add timer obj c006a34c! RTMP_TimerListAdd: add timer obj c006a37c! RTMP_TimerListAdd: add timer obj c00734ac! RTMP_TimerListAdd: add timer obj c00735c8! RTMP_TimerListAdd: add timer obj c00734d8! RTMP_TimerListAdd: add timer obj c006aa54! RTMP_TimerListAdd: add timer obj c0008530! RTMP_TimerListAdd: add timer obj c006a75c! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) ff:ac:f2:bb:9b:14:da:b7:6a:22:24:9a:52:dd:14:cc: 23:90:a1:e1:8d:70:11:e5:8d:5b:16:cf:e7:e0:ef:2b: 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 RTMP_TimerListAdd: add timer obj c000812c! AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 5, CalCode = 14 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffffe TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= 1, phase= 0) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 1, phase=3e) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 RTMP_TimerListAdd: add timer obj c006ad34! Main bssid = 00:17:13:xx:xx:xx <==== rt28xx_init, Status=0 0x1300 = 00064380 Raeth v3.0 (Tasklet,SkbRecycle) phy_tx_ring = 0x00d54000, tx_ring = 0xa0d54000 phy_rx_ring0 = 0x00d55000, rx_ring0 = 0xa0d55000 SMACCR1 -- : 0x00000017 SMACCR0 -- : 0x131b2f4a ESW: Link Status Changed - Port0 Link UP CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 ra2880stop()...Done Free TX/RX Ring Memory! RX DESC a0ec8000 size = 2048 RTMP_TimerListAdd: add timer obj c009cb40! RTMP_TimerListAdd: add timer obj c0067ac4! RTMP_TimerListAdd: add timer obj c0067a98! RTMP_TimerListAdd: add timer obj c0067af0! RTMP_TimerListAdd: add timer obj c0067a6c! RTMP_TimerListAdd: add timer obj c000b41c! RTMP_TimerListAdd: add timer obj c000ac64! RTMP_TimerListAdd: add timer obj c000b3ec! RTMP_TimerListAdd: add timer obj c000b794! RTMP_TimerListAdd: add timer obj c000b4e4! RTMP_TimerListAdd: add timer obj c000b514! RTMP_TimerListAdd: add timer obj c000b6d4! RTMP_TimerListAdd: add timer obj c000b704! RTMP_TimerListAdd: add timer obj c006a2ec! RTMP_TimerListAdd: add timer obj c0069b34! RTMP_TimerListAdd: add timer obj c006a2bc! RTMP_TimerListAdd: add timer obj c006a664! RTMP_TimerListAdd: add timer obj c006a3b4! RTMP_TimerListAdd: add timer obj c006a3e4! RTMP_TimerListAdd: add timer obj c006a31c! RTMP_TimerListAdd: add timer obj c006a34c! RTMP_TimerListAdd: add timer obj c006a37c! RTMP_TimerListAdd: add timer obj c00734ac! RTMP_TimerListAdd: add timer obj c00735c8! RTMP_TimerListAdd: add timer obj c00734d8! RTMP_TimerListAdd: add timer obj c006aa54! RTMP_TimerListAdd: add timer obj c0008530! RTMP_TimerListAdd: add timer obj c006a75c! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) ff:ac:f2:bb:9b:14:da:b7:6a:22:24:9a:52:dd:14:cc: 23:90:a1:e1:8d:70:11:e5:8d:5b:16:cf:e7:e0:ef:2b: 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 RTMP_TimerListAdd: add timer obj c000812c! AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 5, CalCode = 14 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffffe TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= f, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 1, phase=3f) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 RTMP_TimerListAdd: add timer obj c006ad34! Main bssid = 00:17:13:xx:xx:xx <==== rt28xx_init, Status=0 0x1300 = 00064380 device ra0 entered promiscuous mode device apcli0 entered promiscuous mode device eth2 entered promiscuous mode br0: port 2(apcli0) entering learning state br0: port 2(apcli0) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state br0: port 2(apcli0) entering learning state br0: port 1(ra0) entering learning state br0: port 2(apcli0) entering learning state br0: port 2(apcli0) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state Raeth v3.0 (Tasklet,SkbRecycle) phy_tx_ring = 0x00d55000, tx_ring = 0xa0d55000 phy_rx_ring0 = 0x00c27000, rx_ring0 = 0xa0c27000 SMACCR1 -- : 0x00000017 SMACCR0 -- : 0x131b2f4a CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 br0: port 3(eth2) entering learning state br0: port 3(eth2) entering learning state switch register base addr to 0xb0000300 write offset 0x1c, value 0x1 write offset 0x4, value 0xd01203a9 br0: port 2(apcli0) entering forwarding state br0: port 1(ra0) entering forwarding state br0: port 3(eth2) entering forwarding state