User Tools

Site Tools


toh:ubiquiti:ubiquiti_nanobeam_ac

Ubiquiti NanoBeam 5AC (NBE-5AC-16)

The Ubiquiti NanoBeam™ AC (product model: NBE-5AC-16) is a lightweight proprietary (based on 802.11ac) access point with a 16 dBi antenna covering 30º and one Passive POE Gigabit Ethernet port based on the AR9342 SoC.

Note that the official firmware is not compatible to 802.11ac as Ubiquiti uses their own TDMA packet timing scheme. Despite the AC in its name, Ubiquiti is not marketing it as 802.11ac, nor intending to support it. This is as far as I know true for all AirMax AC devices. Unlike the older AirMax M devices, which could be set into a 802.11n compatibility mode. Ubiquiti considers AirMax for backhaul purposes only, and intents the Unify series to be for client connectivity.

With the OpenWrt firmware however, the device is normally 802.11ac compatible, can communicate with normal 802.11an/ac client devices, but can no longer communicate with unmodified AirMax AC devices.

Generic Router

Supported Versions

After extensively studying my OEM bootlog with the OEM bootlog from Ubiquiti Nanostation AC loco, realising they load the same WA 8.5.0 firmware, and checking the TFTP recovery procedure, I simply installed the Loco AC firmware on my NanoBeam AC and it worked.

Everything seems to work, only I have the wrong model name in the OpenWrt status screen, and either there is no 2nd 2.4GHz management radio or it is not found by the OpenWrt (UBNT interface did offer a 2nd SSID for management, but I never tried that, it may simply be an alias on the first 5GHz radio)

However, I am still unsure how big the differences are between NanoBeam AC and NanoBeam AC Gen2, and whether the Loco AC would be more like the Gen2 or not. It may matter more on the board ID ( in this case: WA) then on the name of the device.

The following table with NanoBeam devices is therefore not certain, except for the first entry

Version/Model Board ID Release Date Model Specific Notes
NBE-5AC-16 WA board 2015 Works
NBE-5AC-19 XC board 2015 Will likely not work (XC board)
NBE-2AC-13 2WA board ? Will likely not work (2WA board)
NBE-5AC-Gen2 WA board ~2017 May work (same WA board)
NBE-5AC-Gen2 XC board ~2017 Will likely not work (XC board)

Note these older NanoBeam M devices have their own page and are completely different

Version/Model Board ID Release Date Model Specific Notes
NBE-M2-13 XW board ? Use OpenWrt for the AirMax M series
NBE-M5-16 XW board ? Use OpenWrt for the AirMax M series
NBE-M5-19 XW board ? Use OpenWrt for the AirMax M series

Hardware highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
NanoBeam ACAtheros AR93425351664Qualcomm Atheros QCA9880-a/n/ac-1--

The official data sheet list 8MB flash, but the bootlog really shows 16MB, even the OEM mtd table is using/assuming all 16MB so it may even be for all devices, not merely unused space on newer production sets.

Installation

Do remember that if you are still using daily snapshots for the install, that Luci web interface is not be installed by default. You will have to use SSH / Putty on firstboot, and install Luci manually.

The firmware for this ubiquiti device is signed. But since there are no mtd utilities available on the device the original fwupdate.real binary must be used. Please make sure you have got firmware version v8.5.0.36727 installed https://dl.ubnt.com/firmwares/XC-fw/v8.5.0/WA.v8.5.0.36727.180118.1314.bin. The instructions probably won't work for other versions. To install unsigned firmware the fwupdate.real binary (which is in fact just a symlink to ubntbox) must be patched:

hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real
chmod +x /tmp/fwupdate.real

After that the factory image can be installed using the patched binary:

/tmp/fwupdate.real -m /tmp/openwrt-ath79-generic-ubnt-nanostation-ac-loco-squashfs-factory.bin

The complete set including responses:

WA.v8.5.0# hexdump -Cv /bin/ubntbox | grep '14 40 fe fe'
000093a0  14 40 fe fe 00 40 a8 21  82 02 00 03 3c 03 00 48  |.@...@.!....<..H|
WA.v8.5.0# hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real
WA.v8.5.0# chmod +x /tmp/fwupdate.real
WA.v8.5.0# /tmp/fwupdate.real -m /tmp/openwrt-ath79-generic-ubnt-nanostation-ac-loco-squashfs-factory.bin
Writing 'kernel         ' to /dev/mtd2(kernel         ) ...  [%100]
Writing 'rootfs         ' to /dev/mtd3(rootfs         ) ...  [%100]
Done

Troubleshooting

The above instructions were only verified using firmware version v8.5.0.36727.

It will most likely work for any firmware version where

md5sum /bin/fwupdate.real

is

3584df67dd90aeedf4bee71c08292233

I've not had a look at any other firmware versions yet but up/downgrading to version v8.5.0.36727 should always work.

If you do not have any luck with the non-invasive installation and are not afraid of opening your device and have a USB to serial adapter at hand you can always follow the instructions below.

Alternate Installation Instructions

The NanoBeam 5AC devices seem to be ultrasonically welded together and thus cannot be opened. This makes any TTL serial recovery somewhat destructive. (cut open with Dremel tool)

Additional, even if you do get inside the device, from the Ubiquiti Nanostation AC loco info it is reported there seem to be some additional checks in the tftp rescue and they refuse to install any custom firmware. Read the section of the Ubiquiti Nanostation AC loco for more info if you want/need to try.

Then again, the NanoBeam AC (not the Gen2) is older then the Loco AC, maybe the urescue still works similar to the older Ubiquiti NanoStation M2 / Loco M2 devices. Due to the ultrasonic welding I was not inclined to try yet.

Debricking

Pressing the reset button for 20 seconds while powering on sets the device in the normal Ubiquiti recovery mode, with the signal strength leds flashing in an alternating pattern. It essentially runs the urescue utility from uboot (without the -f -e option). Using TFTP client mode to 192.168.1.20 you can then upload signed firmware, for example the 8.5.0 version mentioned above.

Buttons

The Ubiquiti NanoBeam AC has the following buttons:

BUTTON Event
Reset reset

Hardware

Info

Architecture MIPS
Vendor Ubiquiti
Bootloader U-Boot
System-On-Chip Atheros AR9342 - MIPS 74Kc V4.12
CPU/Speed 535 MHz
Flash-Chip Macronix MX25L12805D
Flash size 128 Mbit
RAM 64 MiB
Wireless Atheros AR9342 & Qualcomm/Atheros QCA988X
Ethernet 1000/100/10 Mbit/s (Atheros AR8035 PHY)
USB None
Serial Yes
JTAG No

Flash Layout

Please read the article flash.layout for a better understanding. It contains a couple of explanations. Then let's have a quick view at flash layout of this particular device:

Ubiquiti NanoBeam AC Flash Layout stock firmware
Layer0 m25p128 spi0.0: Macronix MX25L12805D 16384KiB
Layer1 mtd0 mtd1 mtd2 mtd3 mtd4 mtd5
Size in KiB 256KiB 64KiB 1024KiB 14720KiB 256KiB 64KiB
Name u-boot u-boot-env kernel rootfs cfg EEPROM
mountpoint none none none / none none
filesystem none none none SquashFS 4.0 none none
Ubiquiti NanoBeam AC Flash Layout
Layer0 m25p128 spi0.0: Macronix MX25L12805D 16384KiB
Layer1 mtd0 u-boot 256KiB mtd1 u-boot-env 64KiB mtd2 firmware 15744KiB mtd6 cfg 256 KiB mtd7 EEPROM 64KiB
Layer2 mtd3 kernel mtd4 rootfs
mountpoint /
filesystem overlayfs
Layer3 mtd5 rootfs_data
Size in KiB 256KiB 64KiB 256KiB 64KiB
Name u-boot u-boot-env kernel rootfs_data cfg EEPROM
mountpoint none none none /rom /overlay none none
filesystem none none none SquashFS JFFS2 none none

EEPROM = Atheros radio calibration data

cfg = Config partition, contains ubnt device config and persistent storage, remarks on format: Ubiquiti cfg partition

Photos

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Opening the case

The NanoBeam AC devices seem to be ultrasonically welded together and thus cannot be opened. This makes any TTL serial recovery somewhat destructive. (cut open with Dremel tool)

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
FIXME Add photo of serial connection

Serial connection parameters
for Ubiquiti NanoBeam AC
115200, 8N1

JTAG

None

Bootlogs

OEM bootlog

BusyBox v1.19.4 (2018-01-18 13:14:41 EET) built-in shell (ash) Enter 'help' for a list of built-in commands. WA.v8.5.0# dmesg [ 0.000000] Linux version 2.6.32.68 (bamboo@936dddf72593) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 unknown) ) #1 Thu Jan 18 13:19:18 EET 2018 [ 0.000000] flash_size passed from bootloader = 16 [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80293020, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs init=/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),1024k(kernel),14720k(rootfs),256k(cfg),64k(EEPROM) mem=64M panic=3 quiet [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61772k/65536k available (2121k kernel code, 3696k reserved, 511k data, 132k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] plat_time_init: plat time init done [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=133120) [ 0.022000] Mount-cache hash table entries: 512 [ 0.024000] NET: Registered protocol family 16 [ 0.027000] PCIe WLAN H/W found [tries: 1] [ 0.027000] PCI init:ath_pcibios_init [ 0.027000] ath_pcibios_init(419): PCI CMD write: 0x356 [ 0.027000] registering PCI controller with io_map_base unset [ 0.032000] bio: create slab <bio-0> at 0 [ 0.034000] pci 0000:00:00.0: reg 10 64bit mmio: [0x000000-0x1fffff] [ 0.034000] pci 0000:00:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] [ 0.034000] pci 0000:00:00.0: supports D1 D2 [ 0.034000] Returning IRQ 64 [ 0.035000] Switching to clocksource MIPS [ 0.037000] NET: Registered protocol family 2 [ 0.038000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.039000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.039000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.039000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.039000] TCP reno registered [ 0.040000] NET: Registered protocol family 1 [ 0.040000] ATH GPIOC major 0 [ 0.041000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.041000] msgmni has been set to 120 [ 0.042000] io scheduler noop registered (default) [ 0.066000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.067000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A [ 0.067000] console [ttyS0] enabled [ 0.069000] 6 cmdlinepart partitions found on MTD device ath-nor0 [ 0.069000] Creating 6 MTD partitions on "ath-nor0": [ 0.069000] 0x000000000000-0x000000040000 : "u-boot" [ 0.070000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.071000] 0x000000050000-0x000000150000 : "kernel" [ 0.072000] 0x000000150000-0x000000fb0000 : "rootfs" [ 0.073000] mtd: partition "rootfs" set to be root filesystem [ 0.074000] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.075000] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.076000] u32 classifier [ 0.076000] Performance counters on [ 0.076000] input device check on [ 0.076000] Actions configured [ 0.078000] TCP westwood registered [ 0.078000] NET: Registered protocol family 10 [ 0.081000] NET: Registered protocol family 17 [ 0.081000] Bridge firewalling registered [ 0.081000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 0.081000] All bugs added by David S. Miller <davem@redhat.com> [ 0.081000] athwdt_init: Registering WDT success [ 0.082000] Reset: Normal [ 0.082000] ath_otp_init: Registering OTP success [ 0.082000] ath_clksw_init: Registering Clock Switch Interface success [ 0.089000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.090000] Freeing unused kernel memory: 132k freed [ 1.624000] ubnthal: module license 'Proprietary' taints kernel. [ 1.624000] Disabling lock debugging due to kernel taint [ 1.671000] ubnthal: initializing... [ 1.671000] ath-gpio 2.0 initialised [ 1.671000] ubnthal: initialised, board found, sysid = 0xe9f5, name = NanoBeam 5AC 16 [ 1.671000] ubnthal: host_board_t size: 7392B, boards table size: 151kB [ 7.007000] ATHR_GMAC: Length per segment 1536 [ 7.007000] ATHR_GMAC: fifo cfg 3 01f00140 [ 7.008000] Found PHY at address 4 with ID 4d:d072 [ 7.008000] Registering AR8035 Phy.... [ 7.008000] ATHR_GMAC: RX TASKLET - Pkts per Intr:160 [ 7.008000] ATHR_GMAC: Mac address for unit 0:bfff0000 [ 7.008000] ATHR_GMAC: f0:9f:c2:xx:xx:xx [ 7.563000] ATHR_GMAC: Max segments per packet : 1 [ 7.563000] ATHR_GMAC: Max tx descriptor count : 128 [ 7.563000] ATHR_GMAC: Max rx descriptor count : 252 [ 7.563000] ATHR_GMAC: Mac capability flags : 42200 [ 7.676000] PPP generic driver version 2.4.2 [ 7.733000] PPP MPPE Compression module registered [ 7.766000] NET: Registered protocol family 24 [ 7.934000] GRE over IPv4 tunneling driver [ 8.012000] URD Init [ 8.579000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, 11D) [ 8.744000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 8.859000] ath_spectral: Version 2.0.0 [ 8.859000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 8.859000] SPECTRAL module built on Jan 18 2018 13:17:59 [ 9.126000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 11.043000] ath_pci: 10.1.467 (Atheros/multi-bss) [ 11.043000] Ubiquiti U-AME chipset detected [ 11.043000] ath_pci_probe [ 11.043000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 11.044000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x83a7fa00 [ 11.044000] [ 11.044000] ol_ath_pci_configure : num_desired MSI set to 0 [ 11.044000] [ 11.044000] Using PCI Legacy Interrupt [ 11.946000] Target Warm Reset [ 11.946000] Host Intr Cause reg 0x900c : value : 0x0 [ 11.946000] Target CPU Intr Cause 0x0 [ 12.047000] addr 0x4050 : 0x4 [ 12.067000] Target CPU Intr Cause after CE reset 0x0 [ 12.067000] RESET_CONTROL after cpu warm reset 0x800 [ 12.167000] Target Warm reset complete [ 12.380000] __ol_ath_attach: ath_attach TODO [ 12.381000] ol_ath_attach() BMI inited. [ 12.381000] ol_ath_attach() BMI Get Target Info. [ 12.381000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 12.381000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 12.381000] ol_ath_attach() configure Target . [ 12.382000] qc98xx_verify_checksum: flash checksum passed: 0xb9b9 [ 12.382000] ol_transfer_bin_file 338: Download Flash data len 2116 [ 12.395000] BMI operation done [ 12.396000] ol_transfer_bin_file 259: Download Firmware data len 213896. Mode: PTP [ 13.303000] BMI operation done [ 13.303000] ol_ath_attach() Download FW. [ 13.303000] ol_ath_attach() HT Create . [ 13.303000] ol_ath_attach() HIF Claim. [ 13.303000] ol_ath_attach() BMI Done. [ 13.303000] ol_ath_attach() WMI attached. wmi_handle 83ba0000 [ 13.303000] +HWT [ 13.306000] -HWT [ 13.307000] HTC Service:0x0300 ep:1 TX flow control disabled [ 13.311000] ol_txrx_pdev_attach: tx_credit initialised to 1424 [ 13.311000] HTC Service:0x0100 ep:2 TX flow control disabled [ 13.312000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 13.312000] num_rf_chain : 00000002 [ 13.312000] ht_cap_info: : 0000085b [ 13.312000] vht_cap_info : 338001b2 [ 13.312000] vht_supp_mcs : 0000fffa [ 13.321000] FIRMWARE:P 34 V 1 T 110 [ 13.321000] [ 13.321000] wmi_ready_event_rx: WMI UNIFIED READY event [ 13.321000] ol_ath_connect_htc() WMI is ready [ 13.321000] ol_ath_set_host_app_area TODO [ 13.321000] target uses HTT version 2.1; host uses 2.1 [ 13.321000] ol_ath_attach() connect HTC. [ 13.321000] Supported modes: 0x1f9001 [ 13.321000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 13.324000] ol_ath_phyerr_attach: called [ 13.324000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 13.324000] OL Resmgr Init-ed [ 13.325000] ol_if_spectral_setup [ 13.325000] SPECTRAL : get_capability not registered [ 13.325000] HAL_CAP_PHYDIAG : Capable [ 13.325000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 233) [ 13.325000] SPECTRAL : get_capability not registered [ 13.325000] HAL_CAP_RADAR : Capable [ 13.325000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 13.325000] (spectral_attach : 238) [ 13.325000] SPECTRAL : get_capability not registered [ 13.325000] HAL_CAP_SPECTRAL_SCAN : Capable [ 13.325000] SPECTRAL : get_tsf64 not registered [ 13.325000] spectral_init_netlink 54 NULL SKB [ 13.325000] ol_ath_set_dscp_tid_map: ...ath.c [ 13.325000] ol_if_dfs_setup: called [ 13.325000] ol_ath_rtt_meas_report_attach: called [ 13.325000] ol_ath_attach() UMAC attach . [ 13.325000] __ol_ath_attach: init tx/rx TODO [ 13.325000] __ol_ath_attach: hard_header_len reservation 64 [ 13.325000] __ol_ath_attach: dev name wifi0 [ 13.330000] ath_ahb: 10.1.467 (Atheros/multi-bss) [ 13.330000] __ath_attach: Set global_scn[0] [ 13.330000] ACBKMinfree = 48 [ 13.330000] ACBEMinfree = 32 [ 13.330000] ACVIMinfree = 16 [ 13.330000] ACVOMinfree = 0 [ 13.330000] CABMinfree = 48 [ 13.330000] UAPSDMinfree = 0 [ 13.341000] Enterprise mode: 0x00000000 [ 13.341000] Restoring Cal data from Flash [ 13.342000] ar9300_eeprom_restore_internal[4673] No vaid CAL, calling default template [ 13.716000] SPECTRAL : get_capability not registered [ 13.716000] HAL_CAP_PHYDIAG : Capable [ 13.716000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 233) [ 13.716000] SPECTRAL : get_capability not registered [ 13.716000] HAL_CAP_RADAR : Capable [ 13.716000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 13.716000] (spectral_attach : 238) [ 13.716000] SPECTRAL : get_capability not registered [ 13.716000] HAL_CAP_SPECTRAL_SCAN : Capable [ 13.716000] SPECTRAL : get_tsf64 not registered [ 13.716000] spectral_init_netlink 54 NULL SKB [ 13.716000] IRQ request for SPECTRAL-XMIT-FILTER successful [ 13.716000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT [ 13.717000] SPECTRAL : module attached [ 13.720000] ath_get_caps[5783] rx chainmask mismatch actual 3 sc_chainmak 0 [ 13.720000] ath_get_caps[5758] tx chainmask mismatch actual 3 sc_chainmak 0 [ 13.721000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 13.753000] SPECTRAL : module already attached [ 13.756000] ath_tx_paprd_init sc 827a0000 PAPRD disabled in HAL [ 14.040000] wifi1: Atheros 9340: mem=0xb8100000, irq=2 [ 14.267000] ubnt_poll_host: Hooks registered [ 14.268000] ubnt_poll_host: Allocated chardev region for major 189 [ 14.390000] rssi-leds 1.2 loaded [ 14.703000] Mirror/redirect action on [ 23.137000] ath92.ol_ath_set_config_param(): Reset scheduled on wifi0 radio [ 23.137000] Resetting the radio [ 23.137000] Suspending Target - with disable_intr set [ 23.137000] waiting for target paused event from target [ 23.139000] __ol_ath_detach: init tx/rx cleanup TODO [ 23.140000] ol_if_dfs_teardown: called [ 23.140000] ol_ath_phyerr_detach: called [ 23.143000] ol_if_spectral_detach [ 23.143000] SPECTRAL : Module removed (spectral = 83214000) [ 23.143000] ath_pci_warm_reset :(sc 83a7fa00) [ 23.143000] Target Warm Reset [ 23.143000] Host Intr Cause reg 0x900c : value : 0x4000 [ 23.143000] Target CPU Intr Cause 0x5000 [ 23.243000] addr 0x4050 : 0x4 [ 23.263000] Target CPU Intr Cause after CE reset 0x0 [ 23.263000] RESET_CONTROL after cpu warm reset 0x800 [ 23.364000] Target Warm reset complete [ 23.364000] ath_pci_remove [ 23.364000] Ubiquiti U-AME chipset detected [ 23.364000] ath_pci_probe [ 23.364000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 23.364000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x83a7fa00 [ 23.364000] [ 23.364000] ol_ath_pci_configure : num_desired MSI set to 0 [ 23.365000] [ 23.365000] Using PCI Legacy Interrupt [ 23.477000] __ol_ath_attach: ath_attach TODO [ 23.478000] ol_ath_attach() BMI inited. [ 23.483000] ol_ath_attach() BMI Get Target Info. [ 23.483000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 23.483000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 23.484000] ol_ath_attach() configure Target . [ 23.484000] qc98xx_verify_checksum: flash checksum passed: 0xb9b9 [ 23.484000] ol_transfer_bin_file 338: Download Flash data len 2116 [ 23.498000] BMI operation done [ 23.498000] ol_transfer_bin_file 259: Download Firmware data len 213896. Mode: PTP [ 24.420000] BMI operation done [ 24.420000] ol_ath_attach() Download FW. [ 24.420000] ol_ath_attach() HT Create . [ 24.420000] ol_ath_attach() HIF Claim. [ 24.420000] ol_ath_attach() BMI Done. [ 24.420000] ol_ath_attach() WMI attached. wmi_handle 83ba0000 [ 24.420000] +HWT [ 24.423000] -HWT [ 24.423000] HTC Service:0x0300 ep:1 TX flow control disabled [ 24.428000] ol_txrx_pdev_attach: tx_credit initialised to 1424 [ 24.428000] HTC Service:0x0100 ep:2 TX flow control disabled [ 24.429000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 24.429000] num_rf_chain : 00000002 [ 24.429000] ht_cap_info: : 0000085b [ 24.429000] vht_cap_info : 338001b2 [ 24.429000] vht_supp_mcs : 0000fffa [ 24.438000] FIRMWARE:P 34 V 1 T 110 [ 24.438000] [ 24.438000] wmi_ready_event_rx: WMI UNIFIED READY event [ 24.438000] ol_ath_connect_htc() WMI is ready [ 24.438000] ol_ath_set_host_app_area TODO [ 24.438000] ol_ath_attach() connect HTC. [ 24.438000] target uses HTT version 2.1; host uses 2.1 [ 24.438000] Supported modes: 0x1f9001 [ 24.438000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 24.441000] ol_ath_phyerr_attach: called [ 24.441000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 24.441000] OL Resmgr Init-ed [ 24.442000] ol_if_spectral_setup [ 24.442000] SPECTRAL : get_capability not registered [ 24.442000] HAL_CAP_PHYDIAG : Capable [ 24.442000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 233) [ 24.442000] SPECTRAL : get_capability not registered [ 24.442000] HAL_CAP_RADAR : Capable [ 24.442000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 24.442000] (spectral_attach : 238) [ 24.442000] SPECTRAL : get_capability not registered [ 24.442000] HAL_CAP_SPECTRAL_SCAN : Capable [ 24.442000] SPECTRAL : get_tsf64 not registered [ 24.442000] spectral_init_netlink 54 NULL SKB [ 24.442000] ol_ath_set_dscp_tid_map: ...ath.c [ 24.442000] ol_if_dfs_setup: called [ 24.442000] ol_ath_rtt_meas_report_attach: called [ 24.442000] ol_ath_attach() UMAC attach . [ 24.442000] __ol_ath_attach: init tx/rx TODO [ 24.442000] __ol_ath_attach: hard_header_len reservation 64 [ 24.442000] __ol_ath_attach: dev name wifi0 [ 24.447000] Reset of radio done [ 24.520000] ubnt_poll_host: Hooks registered [ 24.520000] ubnt_poll_host: Allocated chardev region for major 189 [ 24.529000] ubnt_poll_host wifi0: Char device created succesfully err 0 [ 24.529000] ubnt_poll_host: Polling enabled for radio wifi0 [ 24.529000] ubnt_poll_host: noack_mode set to 0 for radio wifi0 [ 24.529000] ubnt-poll-host: [wifi0] Station priority configured to 2 (no-auto=0) [ 24.530000] ubnt_poll_host: Fixed frame mode disabled for radio wifi0 [ 24.670000] ath_ioctl: SIOC80211IFCREATE CALLED [ 24.670000] ubnt_poll_host: Initialized in PTP STA mode for device wifi0 [ 24.671000] wmi_unified_set_psmode:set psmode=1 [ 24.671000] ol_if_dfs_configure: called [ 24.671000] ol_if_dfs_configure: FCC domain [ 24.671000] VAP device ath0 created [ 24.742000] ubnt_poll_host: ATPC enabled (0/0/0/24) for radio wifi0 [ 24.826000] [ 24.826000] DES SSID SET=ubnt [ 24.831000] ol_ath_vap_set_param: VAP param unsupported param:33 value:0 [ 24.846000] wmi_unified_set_psmode:set psmode=0 [ 24.846000] wmi_unified_set_psmode:set psmode=0 [ 25.251000] Ebtables v2.0 registered [ 27.091000] device eth0 entered promiscuous mode [ 27.097000] device ath0 entered promiscuous mode [ 27.154000] athr_gmac_ring_alloc Allocated 2048 at 0x823ec800 [ 27.154000] sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000 [ 27.154000] athr_gmac_ring_alloc Allocated 4032 at 0x81c04000 [ 27.154000] sram_desc_cnt 4560,mac Unit 0,Rx r->ring_desc 0xbd000600 [ 27.454000] WASP ----> AR8035 PHY [ 27.455000] AR8035 Detected [ 27.455000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 27.455000] Setting PHY... [ 27.455000] Forced AR8035 PHY hardware reset on PHY setup. [ 27.559000] AR8035 - ID 0x004d:0xd072 [ 33.680000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 34.845000] br0: port 2(ath0) entering learning state [ 35.845000] br0: port 2(ath0) entering forwarding state [ 40.663000] wlan_vap_create : enter. devhandle=0x827902c0, opmode=IEEE80211_M_MONITOR, flags=0x1 [ 40.664000] wlan_vap_create : exit. devhandle=0x827902c0, opmode=IEEE80211_M_MONITOR, flags=0x1. [ 40.664000] VAP device airview1 created [ 41.042000] [ 41.042000] DES SSID SET=spectral [ 54.678000] ATH_MAC_TIMER: enet unit:0 is up (RGMii 100Mbps full duplex) [ 54.678000] ATH_MAC_TIMER: done cfg2 0x7115 ifctl 0x10000 miictrl [ 54.678000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.678000] br0: port 1(eth0) entering learning state [ 55.678000] br0: port 1(eth0) entering forwarding state WA.v8.5.0#


Ubiquiti Radio info

WA.v8.5.0# iwconfig lo no wireless extensions. eth0 no wireless extensions. gre0 no wireless extensions. wifi1 no wireless extensions. teql0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11ac ESSID:"Device under test AC" Mode:Master Frequency:5.185 GHz Access Point: F0:9F:C2:xx:xx:xx Bit Rate:400 Mb/s Tx-Power=7 dBm RTS thr:off Fragment thr:off Center1-Freq: 5.195 GHz Encryption key:4217-94BF-0711-6C1C-A538-2FCA-3C91-0C96 [2] Security mode:open Power Management:off Link Quality=0/94 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 br0 no wireless extensions. airview1 IEEE 802.11na ESSID:"spectral" Mode:Monitor Frequency:5.1 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Tx-Power:13 dBm RTS thr:off Fragment thr:off Center1-Freq: 5.1 GHz Encryption key:off Power Management:off Link Quality=0/94 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0


OpenWrt bootlog

login as: root BusyBox v1.29.3 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r7994+175-ded905ce43 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:~# dmesg [ 0.000000] Linux version 4.14.72 (tsys@arch-build) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7275-f076ad8074)) #0 Thu Sep 27 01:35:38 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is Ubiquiti Nanostation AC loco (WA) [ 0.000000] SoC: Atheros AR9342 rev 2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 805013a0, node_mem_map 81006ee0 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 58344K/65536K available (3703K kernel code, 144K rwdata, 896K rodata, 1200K init, 204K bss, 7192K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 535.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns [ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns [ 0.008328] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.094953] pid_max: default: 32768 minimum: 301 [ 0.100108] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.107169] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.119326] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.129848] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.136435] pinctrl core: initialized pinctrl subsystem [ 0.143150] NET: Registered protocol family 16 [ 0.155951] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges: [ 0.162886] MEM 0x0000000010000000..0x0000000013ffffff [ 0.168443] IO 0x0000000000000000..0x0000000000000000 [ 0.193460] PCI host bridge to bus 0000:00 [ 0.197896] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.205208] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.211154] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.218373] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.226855] pci 0000:00:00.0: [0777:11ac] type 00 class 0x028000 [ 0.226918] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.226976] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.227060] pci 0000:00:00.0: supports D1 D2 [ 0.227298] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.227330] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.235134] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.243575] clocksource: Switched to clocksource MIPS [ 0.250142] NET: Registered protocol family 2 [ 0.255750] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.263189] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.270024] TCP: Hash tables configured (established 1024 bind 1024) [ 0.276963] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.283201] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.290236] NET: Registered protocol family 1 [ 0.294977] PCI: CLS 0 bytes, default 32 [ 0.300257] Crashlog allocated RAM at address 0x3f00000 [ 0.307388] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.319798] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.326061] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.347081] io scheduler noop registered [ 0.351264] io scheduler deadline registered (default) [ 0.359290] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68 [ 0.367873] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.375545] console [ttyS0] disabled [ 0.379402] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 2500000) is a 16550A [ 0.388646] console [ttyS0] enabled [ 0.396082] bootconsole [early0] disabled [ 0.417103] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.422299] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.428800] Creating 5 MTD partitions on "spi0.0": [ 0.433683] 0x000000000000-0x000000040000 : "u-boot" [ 0.439690] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.446146] 0x000000050000-0x000000fb0000 : "firmware" [ 0.473832] 2 uimage-fw partitions found on MTD device firmware [ 0.479862] 0x000000050000-0x0000001e0000 : "kernel" [ 0.485815] 0x0000001e0000-0x000000fb0000 : "rootfs" [ 0.491666] mtd: device 4 (rootfs) set to be root filesystem [ 0.497506] 1 squashfs-split partitions found on MTD device rootfs [ 0.503817] 0x000000670000-0x000000fb0000 : "rootfs_data" [ 0.510220] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.515966] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.523197] libphy: Fixed MDIO Bus: probed [ 0.864001] libphy: ag71xx_mdio: probed [ 1.303782] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:04 [uid=004dd072, driver=Atheros 8035 ethernet] [ 1.314830] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 1.322928] NET: Registered protocol family 10 [ 1.331648] Segment Routing with IPv6 [ 1.335581] NET: Registered protocol family 17 [ 1.340153] 8021q: 802.1Q VLAN Support v1.8 [ 1.351924] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.366958] Freeing unused kernel memory: 1200K [ 1.371559] This architecture does not have kernel memory protection. [ 2.063546] init: Console is alive [ 2.067348] init: - watchdog - [ 2.483592] random: fast init done [ 3.122818] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.177233] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.195141] init: - preinit - [ 4.614832] random: jshn: uninitialized urandom read (4 bytes read) [ 4.915466] random: jshn: uninitialized urandom read (4 bytes read) [ 4.961107] random: jshn: uninitialized urandom read (4 bytes read) [ 5.186820] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.508710] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 8.545152] urandom-seed: Seed file not found (/etc/urandom.seed) [ 8.677943] procd: - early - [ 8.680990] procd: - watchdog - [ 9.273717] procd: - watchdog - [ 9.277234] procd: - ubus - [ 9.338190] urandom_read: 4 callbacks suppressed [ 9.338200] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.350942] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.358024] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.365731] procd: - init - [ 9.775926] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.787704] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.807001] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85 [ 9.814836] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd [ 9.825539] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.841019] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 9.918818] xt_time: kernel timezone is -0000 [ 10.156937] PPP generic driver version 2.4.2 [ 10.164272] NET: Registered protocol family 24 [ 10.203748] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 10.209671] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 10.488341] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 10.499243] ath10k_pci 0000:00:00.0: Falling back to user helper [ 10.713076] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 10.722592] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2 [ 10.733140] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.031772] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2 [ 11.042695] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.233853] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed [ 11.250082] ath10k_pci 0000:00:00.0: qca988x hw2.0 ubiquiti target 0x4100016c chip_id 0x043222ff sub 0777:e9f5 [ 11.260283] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 11.275164] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb [ 11.373843] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 [ 11.384487] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.568057] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 11.577542] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 12.720676] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 12.865782] ath: EEPROM regdomain: 0x0 [ 12.865792] ath: EEPROM indicates default country code should be used [ 12.865797] ath: doing EEPROM country->regdmn map search [ 12.865814] ath: country maps to regdmn code: 0x3a [ 12.865820] ath: Country alpha2 being used: US [ 12.865825] ath: Regpair used: 0x3a [ 12.948905] ath: phy1: Unable to initialize hardware; initialization status: -5 [ 12.956395] ath9k 18100000.wmac: failed to initialize device [ 12.962195] ath9k: probe of 18100000.wmac failed with error -5 [ 13.055737] kmodloader: done loading kernel modules from /etc/modules.d/* [ 28.244168] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 28.251178] jffs2_build_filesystem(): unlocking the mtd device... [ 28.251184] done. [ 28.259476] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 29.071684] eth0: link up (100Mbps/Full duplex) [ 29.095859] br-lan: port 1(eth0) entered blocking state [ 29.101174] br-lan: port 1(eth0) entered disabled state [ 29.106908] device eth0 entered promiscuous mode [ 29.193864] br-lan: port 1(eth0) entered blocking state [ 29.199183] br-lan: port 1(eth0) entered forwarding state [ 29.204924] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 30.113663] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 72.064474] done. [ 72.066481] jffs2: notice: (1177) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 72.310099] overlayfs: upper fs does not support tmpfile. [ 128.993631] random: crng init done root@OpenWrt:~#


OpenWrt Wifi Radio info

Note that the NanoBeam AC does not seem to have the 2nd 2.4Ghz radio. Which is odd, because the original firmware did offer the 2nd SSID for management purposes. I am unsure if maybe only the Gen2 has an actual 2nd radio, or of the firmware I loaded does not address the correct chip

root@OpenWrt:~# iwconfig lo no wireless extensions. eth0 no wireless extensions. br-lan no wireless extensions. wlan0 IEEE 802.11 ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm RTS thr:off Fragment thr:off Encryption key:off Power Management:off root@OpenWrt:~# iw list Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes max # sched scan SSIDs: 0 max # match sets: 0 max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x3 RX 0x3 Configured Antennas: TX 0x3 RX 0x3 Supported interface modes: * managed * AP * monitor * mesh point Band 2: Capabilities: 0x19ef RX LDPC HT20/HT40 SM Power Save disabled RX HT20 SGI RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 7935 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-15 VHT Capabilities (0x338001b2): Max MPDU length: 11454 Supported Channel Width: neither 160 nor 80+80 RX LDPC short GI (80 MHz) TX STBC RX antenna pattern consistency TX antenna pattern consistency VHT RX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 0 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 0 Mbps Frequencies: * 5180 MHz [36] (23.0 dBm) * 5200 MHz [40] (23.0 dBm) * 5220 MHz [44] (23.0 dBm) * 5240 MHz [48] (23.0 dBm) * 5260 MHz [52] (23.0 dBm) (radar detection) * 5280 MHz [56] (23.0 dBm) (radar detection) * 5300 MHz [60] (23.0 dBm) (radar detection) * 5320 MHz [64] (23.0 dBm) (radar detection) * 5500 MHz [100] (23.0 dBm) (radar detection) * 5520 MHz [104] (23.0 dBm) (radar detection) * 5540 MHz [108] (23.0 dBm) (radar detection) * 5560 MHz [112] (23.0 dBm) (radar detection) * 5580 MHz [116] (23.0 dBm) (radar detection) * 5600 MHz [120] (23.0 dBm) (radar detection) * 5620 MHz [124] (23.0 dBm) (radar detection) * 5640 MHz [128] (23.0 dBm) (radar detection) * 5660 MHz [132] (23.0 dBm) (radar detection) * 5680 MHz [136] (23.0 dBm) (radar detection) * 5700 MHz [140] (23.0 dBm) (radar detection) * 5720 MHz [144] (23.0 dBm) (radar detection) * 5745 MHz [149] (30.0 dBm) * 5765 MHz [153] (30.0 dBm) * 5785 MHz [157] (30.0 dBm) * 5805 MHz [161] (30.0 dBm) * 5825 MHz [165] (30.0 dBm) * 5845 MHz [169] (disabled) * 5865 MHz [173] (disabled) valid interface combinations: * #{ AP, mesh point } <= 8, #{ managed } <= 1, total <= 8, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz } HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports VHT-IBSS. root@OpenWrt:~#


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/ubiquiti/ubiquiti_nanobeam_ac.txt · Last modified: 2019/03/23 08:10 by tmomas