User Tools

Site Tools


toh:ubiquiti:ubiquiti_edgerouter

Ubiquiti EdgeRouter

8 Port Gigabit Router

Generic Router

Supported Versions

Experimental Versions

None at this time.

Hardware Highlights

Installation

Flash Layout

The layout of the SPI flash is not known, mostly because it is not important since the installation and operation of OpenWrt occurs entirely within the eMMC flash drive. The eMMC drive contains two partitions, one holding the kernel and the other is the rootfs.

Easy installation via Serial and USB

  1. Get the appropriate RJ45 Console Port cable (see below for details)
  2. Create a USB Drive with a single FAT32 partition (32MB should be adequate).
  3. Download octeon-er-initramfs-kernel.bin from either current or snapshot release onto the USB Drive – You can rename the file to initramfs-kernel.bin
  4. Download octeon-er-squashfs-sysupgrade.tar from either current or snapshot release onto the USB Drive - You can rename the file to sysupgrade.tar
  5. Unplug the power cord.
  6. Connect the Console Cable
  7. Start a Terminal-Client (8N1 115200 Baud), for example by running screen /dev/ttyUSB0 115200
  8. Plug in the power cord.
  9. Immediately hold down the enter key on your keyboard.
  10. This should halt the boot process and give you a Bootloader-Prompt Octeon ubnt_e200# (If the device continues to boot try again).
  11. Read the initramfs-kernel.bin file from USB into RAM as below:
    Octeon ubnt_e200# usb start
    (Re)start USB...
    USB:   USB EHCI 1.00
    scanning bus for devices... 2 USB Device(s) found
           scanning bus for storage devices... 1 Storage Device(s) found
    Octeon ubnt_e200# usb part 0
    
    Partition Map for USB device 0  --   Partition Type: DOS
    
    Partition     Start Sector     Num Sectors     Type
        1                 2048        15824896       b
    Octeon ubnt_e200# fatload usb 0:1 0x20000000 initramfs-kernel.bin
    reading initramfs-kernel.bin
    
    14688528 bytes read
    Octeon ubnt_e200# bootoctlinux 0 numcores=2 endbootargs mem=0
  12. A minimal OpenWrt environment will boot from RAM. Wait until the boot finishes and hit Enter. It should appear similar to below:
    BusyBox v1.30.1 () built-in shell (ash)
    
      _______                     ________        __
     |       |.-----.-----.-----.|  |  |  |.----.|  |_
     |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
     |_______||   __|_____|__|__||________||__|  |____|
              |__| W I R E L E S S   F R E E D O M
     -----------------------------------------------------
     OpenWrt 19.07.4, r11208-ce6496d796
     -----------------------------------------------------
    === WARNING! =====================================
    There is no root password defined on this device!
    Use the "passwd" command to set up a new password
    in order to prevent unauthorized SSH logins.
    --------------------------------------------------
  13. Now mount the USB device and run sys upgrade as below to install to the internal eMMC drive:
    root@OpenWrt:/# mount /dev/sda1 /mnt
    root@OpenWrt:/# sysupgrade /mnt/squashfs-sysupgrade.tar
    Image not in /tmp, copying...
    Image metadata not found
    Saving config files...
    Commencing upgrade. Closing all shell sessions.
    Watchdog handover: fd=3
    - watchdog -
    killall: telnetd: no process killed
    Sending TERM to remaining processes ... uhttpd ntpd udhcpc odhcp6c fw3 ubusd urngd logd rpcd dnsmasq netifd odhcpd 
    Sending KILL to remaining processes ... 
    Switching to ramdisk...
    Performing system upgrade...
    flashing kernel to /dev/mmcblk0p1
    flashing rootfs to /dev/mmcblk0p2
    567+1 records in
    567+1 records out
    Upgrade completed
    Rebooting system...
    umount: can't unmount /dev: Resource busy
    umount: can't unmount /tmp: Resource busy
    [  332.085722] reboot: Restarting system
  14. The EdgeRouter now reboots into the newly flashed OpenWrt system and you can proceed with configuration.

OEM installation using the TFTP method

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

Upgrading OpenWrt

generic.sysupgrade

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line.

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan (eth0) LAN port 0 192.168.1.1/24
wan (eth1) LAN port 1 DHCP
(eth2) LAN port 2 Not configured
(eth3) LAN port 3 Not configured
(eth4) LAN port 4 Not configured
(eth5) LAN port 5 Not configured
(eth6) LAN port 6 Not configured
(eth7) LAN port 7 Not configured

The bridge on eth0 is useless since eth2-7 are not configured, and disabling it might increase performance.

Switch Ports (for VLANs)

No Switch Ports on device

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The Ubiquiti EdgeRouter has the following buttons:

BUTTON Event
Reset reset

Hardware

Info

General
Brand Ubiquiti
Model EdgeRouter (ER-8)
Versions
Device Type Router
Availability Available 2020
Comments - general
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1b6dece9eaf60a041fd557edb07e55133a86f099
Supported Since Release 15.05
Supported Current Release 19.07.4
Unsupported
Hardware
Bootloader U-Boot
Target octeon
System-On-Chip Cavium CN6120
CPU MHz 800
Flash MB 4096 eMMC
RAM MB 2048
Network
Ethernet 100M ports -
Ethernet Gbit ports 8
Switch
Modem -
VLAN ¿
Comments - network ports
Wireless
WLAN 2.4GHz -
WLAN 5.0GHz -
WLAN Hardware
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports 1x 2.0
SATA ports -
Serial Yes
JTAG Yes
Comments - USB & SATA ports
Misc
LED count 1
Button count 1
Power supply 100 - 240 VAC, 50/60 Hz
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/Ubiquiti_Networks_EdgeRouter
OEM device homepage URL https://www.ubnt.com/edgemax/edgerouter/
Firmware OEM Stock URL https://www.ui.com/download/edgemax/edgerouter
Firmware OpenWrt Install URL http://downloads.openwrt.org/releases/19.07.4/targets/octeon/generic/openwrt-19.07.4-octeon-er-initramfs-kernel.bin
Firmware OpenWrt Upgrade URL http://downloads.openwrt.org/releases/19.07.4/targets/octeon/generic/openwrt-19.07.4-octeon-er-squashfs-sysupgrade.tar
Edit the underlying data View/Edit data

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:

Opening the case

Note: This will void your warranty!

The case is easily opened by removing the 3 Phillips head screws at the lower back of the device. Then pull the top back from the front plate.

Main PCB:

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

There is an RJ45 console port which can be used with an RJ45 to 9pin serial cable or RJ45 to USB Console cable. The connector pinout is the same as those found on much Cisco equipment and it uses true RS-232 levels. USB to TTL adapters must not be connected to this port, as the voltage levels are not compatible. Use a USB to RS-232 adapter or 9 pin RS-232 port mostly found on older computers, along with a 9 pin to RJ45 adapter wired to the Cisco standard.

Serial connection parameters
for Ubiquiti EdgeRouter
115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

There appears to be a standard 14-pin JTAG port located at J2.

Bootloader mods

Hardware mods

RAM is provided via a 2GB 204-Pin PC3-12800 SODIMM. There are reports of successful upgrades to both 4GB and 8GB.

Bootlogs

OEM bootlog

Jumping to start of image at address 0xbfca0000 U-Boot 2012.04.01 (UBNT Build Version: e201_002_80eda) (May 27 2019 - 06:35:31) Skipping PCIe port 0 BIST, in EP mode, can't tell if clocked. Skipping PCIe port 1 BIST, reset not done. (port not configured) BIST check passed. UBNT_E200 r1:1, r2:16, serial #: B4FBE48BF8E5 MPR 13-02033-16 Core clock: 800 MHz, IO clock: 600 MHz, DDR clock: 533 MHz (1066 Mhz DDR) Base DRAM address used by u-boot: 0x8f800000, size: 0x800000 DRAM: 2 GiB Clearing DRAM...... done Flash: 8 MiB Net: octeth0, octeth1, octeth2, octeth3, octeth4, octeth5, octeth6, octeth7 MMC: Octeon MMC/SD0: 0 USB: USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found Type the command 'usb start' to scan for USB storage devices. Hit any key to stop autoboot: 0 reading vmlinux.64 6784984 bytes read reading vmlinux.64.md5 argv[2]: numcores=2 argv[3]: endbootargs Allocating memory for ELF segment: addr: 0xffffffff80800000 (adjusted to: 0x800000), size 0x7a32c0 ## Loading big-endian Linux kernel with entry point: 0xffffffff80cbc310 ... Bootloader: Done loading app on coremask: 0x3 Starting cores 0x3 Linux version 4.9.79-UBNT (ubnt@8b46a25fc5c7) (gcc version 4.7.0 (Cavium Inc. Version: SDK_BUILD build 54) ) #1 SMP Tue Jun 9 11:25:41 UTC 2020 CVMSEG size: 2 cache lines (256 bytes) Cavium Inc. SDK-5.1.0 bootconsole [early0] enabled CPU0 revision is: 000d9301 (Cavium Octeon II) Checking for the multiply/shift bug... no. Checking for the daddiu bug... no. Determined physical RAM map: memory: 000000006f800000 @ 0000000020000000 (usable) memory: 0000000000c00000 @ 000000000f300000 (usable) memory: 000000000e000000 @ 0000000001100000 (usable) memory: 0000000000400000 @ 0000000000300000 (usable) memory: 0000000000638000 @ 0000000000800000 (kernel data and code) memory: 0000000000124000 @ 0000000000e80000 (kernel data and code) memory: 0000000000048000 @ 0000000000e38000 (usable after init) Wasting 43008 bytes for tracking 768 unused pages Using passed Device Tree <8000000000080000>. Using passed Device Tree. UBNT board DTS pruning ... board 20003 major 1 software IO TLB [mem 0x02d27000-0x02d67000] (0MB) mapped at [8000000002d27000-8000000002d66fff] Primary instruction cache 37kB, virtually tagged, 37 way, 8 sets, linesize 128 bytes. Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes. Secondary unified cache 1024kB, 16-way, 512 sets, linesize 128 bytes. Secondary unified cache 1024kB, 16-way, 512 sets, linesize 128 bytes. Zone ranges: DMA32 [mem 0x0000000000300000-0x00000000efffffff] Normal empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000300000-0x00000000006fffff] node 0: [mem 0x0000000000800000-0x0000000000fa3fff] node 0: [mem 0x0000000001100000-0x000000000f0fffff] node 0: [mem 0x000000000f300000-0x000000000fefffff] node 0: [mem 0x0000000020000000-0x000000008f7fffff] Initmem setup node 0 [mem 0x0000000000300000-0x000000008f7fffff] percpu: Embedded 17 pages/cpu @8000000002d74000 s29056 r8192 d32384 u69632 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 512989 Kernel command line: root=/dev/mmcblk0p2 rootdelay=10 rw rootsqimg=squashfs.img rootsqwdir=w mtdparts=phys_mapped_flash:640k(boot0),640k(boot1),64k(eeprom) console=ttyS0,115200 rootwait rootflags=data=journal PID hash table entries: 4096 (order: 3, 32768 bytes) Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 2036196K/2080400K available (4878K kernel code, 400K rwdata, 1064K rodata, 288K init, 1164K bss, 44204K reserved, 0K cma-reserved) SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. Build-time adjustment of leaf fanout to 64. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=2 NR_IRQS:511 clocksource: OCTEON_CVMCOUNT: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns Calibrating delay loop (skipped) preset value.. 1600.00 BogoMIPS (lpj=8000000) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) Checking for the daddi bug... no. SMP: Booting CPU01 (CoreId 1)... CPU1 revision is: 000d9301 (Cavium Octeon II) Cpu 1 online Brought up 2 CPUs devtmpfs: initialized clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 4, 65536 bytes) NET: Registered protocol family 16 PTP Clock: Using sclk reference at 600000000 Hz HugeTLB registered 2 MB page size, pre-allocated 0 pages SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb clocksource: Switched to clocksource OCTEON_CVMCOUNT NET: Registered protocol family 2 TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 6, 262144 bytes) TCP: Hash tables configured (established 16384 bind 16384) UDP hash table entries: 1024 (order: 3, 32768 bytes) UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) NET: Registered protocol family 1 octeon_pci_console: Console not created. /proc/octeon_perf: Octeon performance counter interface loaded Info: cvmx_bootmem_find_named_block(__common_bootinfo) not found. workingset: timestamp_bits=62 max_order=19 bucket_order=0 squashfs: version 4.0 (2009/01/31) Phillip Lougher io scheduler noop registered io scheduler cfq registered (default) octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO: base = 480 Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled console [ttyS0] disabled 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 34, base_baud = 37500000) is a OCTEON console [ttyS0] enabled console [ttyS0] enabled bootconsole [early0] disabled bootconsole [early0] disabled 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 35, base_baud = 37500000) is a OCTEON loop: module loaded spi-octeon 1070000001000.spi: OCTEON SPI bus driver ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-platform: EHCI generic platform driver ehci-platform 16f0000000000.ehci: EHCI Host Controller ehci-platform 16f0000000000.ehci: new USB bus registered, assigned bus number 1 ehci-platform 16f0000000000.ehci: irq 56, io mem 0x16f0000000000 random: fast init done ehci-platform 16f0000000000.ehci: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 4.9.79-UBNT ehci_hcd usb usb1: SerialNumber: 16f0000000000.ehci hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform: OHCI generic platform driver ohci-platform 16f0000000400.ohci: Generic Platform OHCI controller ohci-platform 16f0000000400.ohci: new USB bus registered, assigned bus number 2 ohci-platform 16f0000000400.ohci: irq 56, io mem 0x16f0000000400 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: Generic Platform OHCI controller usb usb2: Manufacturer: Linux 4.9.79-UBNT ohci_hcd usb usb2: SerialNumber: 16f0000000400.ohci hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usb-storage i2c-octeon 1180000001000.i2c: probed i2c-octeon 1180000001200.i2c: Error: initial status: 00, forcing STOP to bus i2c-octeon 1180000001200.i2c: probed octeon_wdt: Initial granularity 5 Sec sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman NET: Registered protocol family 17 NET: Registered protocol family 15 L2 lock: TLB refill 256 bytes L2 lock: General exception 128 bytes L2 lock: low-level interrupt 128 bytes L2 lock: interrupt 640 bytes L2 lock: memcpy 1152 bytes Bootbus flash: Setting flash for 8MB flash at 0x1f400000 phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000c9 Amd/Fujitsu Extended Query Table at 0x0040 Amd/Fujitsu Extended Query version 1.1. phys_mapped_flash: Swapping erase regions for top-boot CFI table. number of CFI chips: 1 3 cmdlinepart partitions found on MTD device phys_mapped_flash Creating 3 MTD partitions on "phys_mapped_flash": 0x000000000000-0x0000000a0000 : "boot0" 0x0000000a0000-0x000000140000 : "boot1" 0x000000140000-0x000000150000 : "eeprom" OF: fdt:not creating '/sys/firmware/fdt': CRC check failed Waiting 10 sec before mounting root device... mmc0: new DDR MMC card at address 0001 mmcblk0: mmc0:0001 SEM04G 3.69 GiB mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB mmcblk0rpmb: mmc0:0001 SEM04G partition 3 2.00 MiB mmcblk0: p1 p2 EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support! EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with journalled data mode. Opts: data=journal VFS: Mounted root (overlay filesystem) on device 0:13. devtmpfs: mounted Freeing unused kernel memory: 288K This architecture does not have kernel memory protection. systemd[1]: System time before build time, advancing clock. NET: Registered protocol family 10 ip_tables: (C) 2000-2006 Netfilter Core Team systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) systemd[1]: Detected architecture mips64. Welcome to ESC[1mDebian GNU/Linux 9 (stretch)ESC[0m!


OpenWrt bootlog

Jumping to start of image at address 0xbfca0000 U-Boot 2012.04.01 (UBNT Build Version: e201_002_80eda) (May 27 2019 - 06:35:31) Skipping PCIe port 0 BIST, in EP mode, can't tell if clocked. Skipping PCIe port 1 BIST, reset not done. (port not configured) BIST check passed. UBNT_E200 r1:1, r2:16, serial #: B4FBE48BF8E5 MPR 13-02033-16 Core clock: 800 MHz, IO clock: 600 MHz, DDR clock: 533 MHz (1066 Mhz DDR) Base DRAM address used by u-boot: 0x8f800000, size: 0x800000 DRAM: 2 GiB Clearing DRAM...... done Flash: 8 MiB Net: octeth0, octeth1, octeth2, octeth3, octeth4, octeth5, octeth6, octeth7 MMC: Octeon MMC/SD0: 0 USB: USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found Type the command 'usb start' to scan for USB storage devices. Hit any key to stop autoboot: 0 reading vmlinux.64 6947088 bytes read reading vmlinux.64.md5 argv[2]: numcores=2 argv[3]: endbootargs Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x17ea220 ## Loading big-endian Linux kernel with entry point: 0xffffffff8162f3e0 ... Bootloader: Done loading app on coremask: 0x3 Starting cores 0x3 [ 0.000000] Linux version 4.14.195 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11208-ce6496d796)) #0 SMP Sun Sep 6 16:19:39 2020 [ 0.000000] Skipping L2 locking due to reduced L2 cache size [ 0.000000] CVMSEG size: 2 cache lines (256 bytes) [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 000d9301 (Cavium Octeon II) [ 0.000000] Checking for the multiply/shift bug... no. [ 0.000000] Checking for the daddiu bug... no. [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 000000000c800000 @ 0000000002900000 (usable) [ 0.000000] memory: 0000000000c00000 @ 000000000f200000 (usable) [ 0.000000] memory: 000000006f800000 @ 0000000020000000 (usable) [ 0.000000] memory: 00000000017ea220 @ 0000000001100000 (usable) [ 0.000000] Wasting 243712 bytes for tracking 4352 unused pages [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using passed Device Tree. [ 0.000000] software IO TLB: mapped [mem 0x0291f000-0x0295f000] (0MB) [ 0.000000] Primary instruction cache 37kB, virtually tagged, 37 way, 8 sets, linesize 128 bytes. [ 0.000000] Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes. [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000efffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000028e9fff] [ 0.000000] node 0: [mem 0x0000000002900000-0x000000000f0fffff] [ 0.000000] node 0: [mem 0x000000000f200000-0x000000000fdfffff] [ 0.000000] node 0: [mem 0x0000000020000000-0x000000008f7fffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000008f7fffff] [ 0.000000] random: get_random_bytes called from 0xffffffff8175c6d8 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu s35632 r8192 d29904 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 514320 [ 0.000000] Kernel command line: mtdparts=phys_mapped_flash:640k(boot0)ro,640k(boot1)ro,64k(eeprom)ro root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait console=ttyS0,115200 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Memory: 2011608K/2085800K available (5338K kernel code, 348K rwdata, 812K rodata, 1296K init, 16680K bss, 74192K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32 [ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 127 [ 4.263219] clocksource: OCTEON_CVMCOUNT: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns [ 4.274071] Calibrating delay loop (skipped) preset value.. 1600.00 BogoMIPS (lpj=3200000) [ 4.282306] pid_max: default: 32768 minimum: 301 [ 4.286988] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 4.293601] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 4.301162] Checking for the daddi bug... no. [ 4.305884] Hierarchical SRCU implementation. [ 4.310516] smp: Bringing up secondary CPUs ... [ 4.315223] SMP: Booting CPU01 (CoreId 1)... [ 4.319513] CPU1 revision is: 000d9301 (Cavium Octeon II) [ 4.319625] smp: Brought up 1 node, 2 CPUs [ 4.331673] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 4.341284] futex hash table entries: 512 (order: 4, 65536 bytes) [ 4.347757] NET: Registered protocol family 16 [ 4.357181] PCIe: Port 0 in endpoint mode, skipping. [ 4.362007] PCIe: Initializing port 1 [ 4.376638] PCIe: Port 1 stuck in reset, skipping. [ 4.388318] SCSI subsystem initialized [ 4.392136] usbcore: registered new interface driver usbfs [ 4.397547] usbcore: registered new interface driver hub [ 4.402824] usbcore: registered new device driver usb [ 4.407992] PCI host bridge to bus 0000:00 [ 4.411946] pci_bus 0000:00: root bus resource [mem 0x1000000000000] [ 4.418284] pci_bus 0000:00: root bus resource [io 0x0000] [ 4.423847] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 4.430628] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 4.439389] clocksource: Switched to clocksource OCTEON_CVMCOUNT [ 4.445993] NET: Registered protocol family 2 [ 4.450704] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 4.457981] TCP bind hash table entries: 16384 (order: 7, 524288 bytes) [ 4.464833] TCP: Hash tables configured (established 16384 bind 16384) [ 4.471313] UDP hash table entries: 1024 (order: 4, 98304 bytes) [ 4.477278] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes) [ 4.483838] NET: Registered protocol family 1 [ 4.489022] Crashlog allocated RAM at address 0x3f00000 [ 4.494231] workingset: timestamp_bits=62 max_order=19 bucket_order=0 [ 4.505649] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 4.511500] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 4.523152] io scheduler noop registered [ 4.526941] io scheduler deadline registered (default) [ 4.532354] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO driver probed. [ 4.539904] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 4.539906] random: fast init done [ 4.551089] console [ttyS0] disabled [ 4.554550] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 34, base_baud = 37500000) is a OCTEON [ 4.564358] console [ttyS0] enabled [ 4.564358] console [ttyS0] enabled [ 4.571300] bootconsole [early0] disabled [ 4.571300] bootconsole [early0] disabled [ 4.579589] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 35, base_baud = 37500000) is a OCTEON [ 4.589730] octeon_rng octeon_rng: Octeon Random Number Generator [ 4.599052] loop: module loaded [ 4.602652] of-flash 1f400000.nor: Can't get bank width from device tree [ 4.609601] libphy: mdio_octeon: probed [ 4.616011] mdio_octeon 1180000001800.mdio: Probed [ 4.620957] libphy: mdio_octeon: probed [ 4.624824] mdio_octeon 1180000001900.mdio: Probed [ 4.629860] libphy: Fixed MDIO Bus: probed [ 4.634071] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.640630] ehci-pci: EHCI PCI platform driver [ 4.645141] ehci-platform: EHCI generic platform driver [ 4.650539] ehci-platform 16f0000000000.ehci: EHCI Host Controller [ 4.656774] ehci-platform 16f0000000000.ehci: new USB bus registered, assigned bus number 1 [ 4.665241] ehci-platform 16f0000000000.ehci: irq 56, io mem 0x16f0000000000 [ 4.687360] ehci-platform 16f0000000000.ehci: USB 2.0 started, EHCI 1.00 [ 4.694572] hub 1-0:1.0: USB hub found [ 4.698391] hub 1-0:1.0: 2 ports detected [ 4.702771] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.709003] ohci-platform: OHCI generic platform driver [ 4.714385] ohci-platform 16f0000000400.ohci: Generic Platform OHCI controller [ 4.721659] ohci-platform 16f0000000400.ohci: new USB bus registered, assigned bus number 2 [ 4.730107] ohci-platform 16f0000000400.ohci: irq 56, io mem 0x16f0000000400 [ 4.799784] hub 2-0:1.0: USB hub found [ 4.803649] hub 2-0:1.0: 2 ports detected [ 4.808126] usbcore: registered new interface driver usb-storage [ 4.814196] octeon_wdt: Initial granularity 5 Sec [ 4.860993] Interface 0 has 4 ports (SGMII) [ 4.865258] Interface 1 has 4 ports (SGMII) [ 4.873499] NET: Registered protocol family 10 [ 4.879776] Segment Routing with IPv6 [ 4.883534] NET: Registered protocol family 17 [ 4.888039] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.901032] 8021q: 802.1Q VLAN Support v1.8 [ 4.905420] Bootbus flash: Setting flash for 8MB flash at 0x1f400000 [ 14.237039] phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000c9 [ 14.247428] Amd/Fujitsu Extended Query Table at 0x0040 [ 14.252612] Amd/Fujitsu Extended Query version 1.1. [ 14.257690] phys_mapped_flash: Swapping erase regions for top-boot CFI table. [ 14.264854] number of CFI chips: 1 [ 14.268292] 3 cmdlinepart partitions found on MTD device phys_mapped_flash [ 14.275194] Creating 3 MTD partitions on "phys_mapped_flash": [ 14.280969] 0x000000000000-0x0000000a0000 : "boot0" [ 14.286379] 0x0000000a0000-0x000000140000 : "boot1" [ 14.291760] 0x000000140000-0x000000150000 : "eeprom" [ 14.297864] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed [ 14.304743] Waiting for root device /dev/mmcblk0p2... [ 14.331031] mmc0: new DDR MMC card at address 0001 [ 14.336115] mmcblk0: mmc0:0001 SEM04G 3.69 GiB [ 14.340805] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 14.346890] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 14.352903] mmcblk0rpmb: mmc0:0001 SEM04G partition 3 2.00 MiB, chardev (252:0) [ 14.360898] mmcblk0: p1 p2 [ 14.378128] VFS: Mounted root (squashfs filesystem) readonly on device 179:2. [ 14.385869] Freeing unused kernel memory: 1296K [ 14.390441] This architecture does not have kernel memory protection. [ 14.809966] init: Console is alive [ 14.813545] init: - watchdog - [ 15.013011] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 15.019976] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 15.028451] init: - preinit - [ 15.533989] random: jshn: uninitialized urandom read (4 bytes read) [ 15.563911] random: jshn: uninitialized urandom read (4 bytes read) [ 15.586168] random: jshn: uninitialized urandom read (4 bytes read) [ 15.607126] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 19.066032] F2FS-fs (loop0): Mounted with checkpoint version = 3e14b333 [ 19.073411] mount_root: switching to f2fs overlay [ 19.124190] urandom-seed: Seeding with /etc/urandom.seed [ 19.229033] procd: - early - [ 19.232013] procd: - watchdog - [ 19.827397] procd: - watchdog - [ 19.830766] procd: - ubus - [ 19.879657] urandom_read: 1 callbacks suppressed [ 19.879663] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.917866] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.924422] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.931387] procd: - init - Please press Enter to activate this console. [ 20.158644] kmodloader: loading kernel modules from /etc/modules.d/* [ 20.194140] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 20.201782] urngd: v1.0.2 started. [ 20.203248] ip_tables: (C) 2000-2006 Netfilter Core Team [ 20.214286] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 20.241080] xt_time: kernel timezone is -0000 [ 20.249496] PPP generic driver version 2.4.2 [ 20.254956] NET: Registered protocol family 24 [ 20.260283] random: crng init done [ 20.260871] kmodloader: done loading kernel modules from /etc/modules.d/* [ 20.263738] random: 3 urandom warning(s) missed due to ratelimiting [ 23.584893] br-lan: port 1(eth0) entered blocking state [ 23.590175] br-lan: port 1(eth0) entered disabled state [ 23.595612] device eth0 entered promiscuous mode [ 23.618342] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 23.643321] eth1: 1000 Mbps Full duplex, port 17, queue 17 [ 23.649014] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 24.643546] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready BusyBox v1.30.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 19.07.4, r11208-ce6496d796 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. --------------------------------------------------


Notes

Space for additional notes, links to forum threads or other resources.

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/ubiquiti/ubiquiti_edgerouter.txt · Last modified: 2020/10/09 06:43 by raylynnknight