User Tools

Site Tools


toh:ubiquiti:powerbeam

Ubiquiti PowerBeam M

The Ubiquiti Networks® PowerBeam® devices are CPE equipment for customer locations with one Ethernet port and a 2 GHz (PBE-M2-x00) or 5 GHz (PBE-M5-x00) wireless interface.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
PowerBeam M2-400Atheros AR9344560864¿b/g/n-1---
PowerBeam M5-300Atheros AR9xxx560864¿-a/n1---
PowerBeam M5-400Atheros AR9342535864¿-a/n-1--

Installation

TFTP recovery

Hold down reset button while plugging in at least 30 seconds until LED 1 & 3 is altenating to LED 2 & 4. See also: TFTP recovery and LED codes Setup your computer to 192.168.1.5/24, start TFTP transfer:

tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put XW.v5.5.10-u2.28005.150723.1358.bin
tftp> quit

Misc info

PBE-M5-400

/proc/cpuinfo

system type		: Atheros AR934x
processor		: 0
cpu model		: MIPS 74Kc V4.12
BogoMIPS		: 266.24
wait instruction	: yes
microsecond timers	: yes
tlb_entries		: 32
extra interrupt vector	: yes
hardware watchpoint	: yes, count: 4, address/irw mask: [0x0000, 0x0020, 0x0068, 0x00c0]
ASEs implemented	: mips16 dsp
shadow register sets	: 1
core			: 0
VCED exceptions		: not available
VCEI exceptions		: not available

OEM bootlog

XW.v5.5.10# dmesg [ 0.000000] Linux version 2.6.32.60 (buildd@builder) (gcc version 4.1.2) #1 Wed Oct 1 16:43:27 EEST 2014 [ 0.000000] flash_size passed from bootloader = 8 [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802a4a50, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=tty0 root=31:03 rootfstype=squashfs init=/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),1024k(kernel),6528k(rootfs),256k(cfg),64k(EEPROM) mem=64M panic=3 quiet [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61916k/65536k available (2179k kernel code, 3548k reserved, 524k data, 136k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] plat_time_init: plat time init done [ 0.000000] r4k_clockevent_init: Ignoring int_usable failure [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=133120) [ 0.022000] Mount-cache hash table entries: 512 [ 0.025000] NET: Registered protocol family 16 [ 0.033000] bio: create slab <bio-0> at 0 [ 0.035000] Switching to clocksource MIPS [ 0.037000] NET: Registered protocol family 2 [ 0.038000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.039000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.039000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.039000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.039000] TCP reno registered [ 0.040000] NET: Registered protocol family 1 [ 0.040000] ATH GPIOC major 0 [ 0.042000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.042000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.042000] msgmni has been set to 121 [ 0.043000] io scheduler noop registered (default) [ 0.066000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.068000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A [ 0.069000] 6 cmdlinepart partitions found on MTD device ath-nor0 [ 0.069000] Creating 6 MTD partitions on "ath-nor0": [ 0.069000] 0x000000000000-0x000000040000 : "u-boot" [ 0.070000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.072000] 0x000000050000-0x000000150000 : "kernel" [ 0.073000] 0x000000150000-0x0000007b0000 : "rootfs" [ 0.074000] mtd: partition "rootfs" set to be root filesystem [ 0.074000] 0x0000007b0000-0x0000007f0000 : "cfg" [ 0.075000] 0x0000007f0000-0x000000800000 : "EEPROM" [ 0.076000] u32 classifier [ 0.076000] Performance counters on [ 0.076000] input device check on [ 0.076000] Actions configured [ 0.078000] TCP westwood registered [ 0.078000] NET: Registered protocol family 10 [ 0.082000] NET: Registered protocol family 17 [ 0.082000] Bridge firewalling registered [ 0.082000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 0.082000] All bugs added by David S. Miller <davem@redhat.com> [ 0.082000] athwdt_init: Registering WDT success [ 0.082000] ath_otp_init: Registering OTP success [ 0.083000] ath_clksw_init: Registering Clock Switch Interface success [ 0.089000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.090000] Freeing unused kernel memory: 136k freed [ 0.099000] Please be patient, while AirOS loads ... [ 0.895000] Algorithmics/MIPS FPU Emulator v1.5 [ 5.969000] ar7240-gpio 1.1 initialised [ 6.057000] ATHR_GMAC: Length per segment 1536 [ 6.057000] ATHR_GMAC: skb_overhead 64, shinfo: 344 [ 6.057000] ATHR_GMAC: RX sizes - 2k_fit: 1610, reserve: 0 [ 6.057000] ATHR_GMAC: fifo cfg 3 01f00140 [ 6.057000] AR8035 Detected [ 6.057000] ATHR_GMAC: Mac address for unit 0:bfff0000 [ 6.057000] ATHR_GMAC: 00:00:00:00:00:00 [ 6.614000] mac:0 Registering S27.... [ 6.614000] ATHR_GMAC: Max segments per packet : 1 [ 6.615000] ATHR_GMAC: Max tx descriptor count : 128 [ 6.615000] ATHR_GMAC: Max rx descriptor count : 252 [ 6.615000] ATHR_GMAC: Mac capability flags : 4380 [ 6.615000] ATHR_GMAC: Mac address for unit 1:bfff0006 [ 6.615000] ATHR_GMAC: 00:00:00:00:00:00 [ 7.171000] mac:1 Registering S27.... [ 7.171000] ATHR_GMAC: Max segments per packet : 1 [ 7.171000] ATHR_GMAC: Max tx descriptor count : 128 [ 7.171000] ATHR_GMAC: Max rx descriptor count : 252 [ 7.171000] ATHR_GMAC: Mac capability flags : 4B80 [ 7.604000] PPP generic driver version 2.4.2 [ 7.761000] PPP MPPE Compression module registered [ 7.789000] NET: Registered protocol family 24 [ 7.934000] urd: module license 'Proprietary' taints kernel. [ 7.934000] Disabling lock debugging due to kernel taint [ 7.938000] URD Init [ 8.785000] ath_hal: 0.9.17.1 (AR9380, DEBUG, REGOPS_FUNC, 11D) [ 9.244000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 9.882000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 10.845000] ath_ahb: 9.2.0_U11.14 (Atheros/multi-bss) [ 10.845000] __ath_attach: Set global_scn[0] [ 10.845000] ACBKMinfree = 48 [ 10.845000] ACBEMinfree = 32 [ 10.845000] ACVIMinfree = 16 [ 10.845000] ACVOMinfree = 0 [ 10.845000] CABMinfree = 48 [ 10.845000] UAPSDMinfree = 0 [ 10.850000] Bootstrap clock 40MHz [ 10.854000] ar9300Attach: This Mac Chip Rev 0x300.2 PCI devid 0x31 [ 10.854000] Wasp Enterprise mode: 0x00000000 [ 10.854000] ar9300RadioAttach: Need analog access recipe!! [ 10.878000] Restoring Cal data from Flash [ 10.878000] Using Cal data from Flash 0xbfff1000 [ 10.879000] ath_hal: Ubiquiti Osprey (0777:e4e5) [ 10.884000] ath_get_caps[5384] rx chainmask mismatch actual 3 sc_chainmak 0 [ 10.884000] ath_get_caps[5359] tx chainmask mismatch actual 3 sc_chainmak 0 [ 10.900000] wifi0: Atheros 9340: mem=0xb8100000, irq=2 [ 11.538000] ubnt_poll: Initializing polling module... [ 11.538000] ubnt_poll: Initializing packet classifier... [ 11.538000] ubnt_poll: OS timer frequency 1000 Hz [ 11.611000] rssi-leds 1.2 loaded [ 11.681000] ubnt_poll: Attaching hooks... [ 11.763000] wlan_vap_create : enter. devhandle=0x83b602c0, opmode=IEEE80211_M_STA, flags=0x3 [ 11.763000] ubnt_poll: TX CTRL configured with 0/18/200/0/6/0/0 [ 11.763000] ubnt_poll: Initializing STA ranging engine [ 11.763000] VAP attach: burst beacon mode. [ 11.764000] wlan_vap_create : exit. devhandle=0x83b602c0, opmode=IEEE80211_M_STA, flags=0x3. [ 12.423000] Ebtables v2.0 registered [ 13.613000] device eth0 entered promiscuous mode [ 13.618000] device ath0 entered promiscuous mode [ 13.624000] device eth1 entered promiscuous mode [ 13.651000] athr_gmac_ring_alloc Allocated 2048 at 0x8331a800 [ 13.651000] athr_gmac_ring_alloc Allocated 4032 at 0x83356000 [ 13.951000] athr_gmac_mii_setup 0 [ 13.951000] WASP ----> AR8035 PHY [ 13.951000] MAC0 MDC is 8 at line 591 [ 13.951000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 13.952000] Setting PHY... [ 16.971000] ATH_MAC_TIMER: MAC 0 PHY 0x04 - LINK NOW UP [link=UP speed=1000Mbps duplex=full duplex carrier=0] [ 16.982000] ubnt_poll: Setting timing params to min:1000 max:3000 offset:3000 tx_time: 3000 init: 5 [ 16.982000] ubnt_poll: Setting aggregation params to non-txop:0 tx-op:0 scheduling:0 [ 16.982000] ubnt_poll: Setting TXOP Window parameters to size:25 timeout-perc:5 [ 16.982000] ubnt_poll: Module started in STA mode [ 19.994000] ADDRCONF(NETDEV_UP): ath0: link is not ready [ 20.000000] ADDRCONF(NETDEV_UP): ath0: link is not ready [ 20.005000] br0: port 1(eth0) entering learning state [ 21.005000] br0: port 1(eth0) entering forwarding state [ 25.097000] athr_gmac_ring_alloc Allocated 2048 at 0x8285d000 [ 25.097000] athr_gmac_ring_alloc Allocated 4032 at 0x83204000 [ 25.405000] athr_gmac_mii_setup 1 [ 25.406000] WASP ----> S27 PHY MDIO [ 25.406000] MAC1 MDC is 7 at line 659 [ 25.406000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 25.406000] ATHRS27: resetting s27 [ 25.515000] ATHRS27: s27 reset done [ 25.529000] Setting PHY... [ 26.634000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 26.640000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 27.035000] eth0: no IPv6 routers present [ 35.548000] br0: no IPv6 routers present


Tags

toh/ubiquiti/powerbeam.txt · Last modified: 2018/12/23 13:29 by damadmai