Ubiquiti LiteBeam 5AC Gen2

Ubiquiti LiteBeam 5AC Gen2 (LBE-5AC-Gen2) is a dual band outdoor PoE CPE packed inside feedhorn that attaches to small directional reflector included in the package. airOS utilizes 2.4GHz wifi as a management radio only, thus it's performance and range are less than 5GHz wifi.

LiteBeam 5AC Gen2

  1. Configure your TFTP server with IP 192.168.1.254
  2. Connect serial console and power up the device
  3. Hit any key to stop autoboot
  4. tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
  5. bootm 0x81000000
  6. copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp
  7. sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
Architecture MIPS
Vendor Ubiquiti
Bootloader U-Boot
System-On-Chip Atheros AR9342 - MIPS 74Kc V4.12
CPU/Speed 535 MHz
Flash-Chip Macronix MX25L12805D
Flash size 16 MiB
RAM 64 MiB
Wireless Atheros AR9342 & Qualcomm/Atheros QCA988X
Ethernet 1000/100/10 Mbit/s (Atheros AR8035 PHY)
USB None
Serial Yes
JTAG No

Please read the article flash.layout for a better understanding. It contains a couple of explanations. Then let's have a quick view at flash layout of this particular device:

Ubiquiti LiteBeam 5AC Gen2 Flash Layout stock firmware
Layer0 m25p128 spi0.0: Macronix MX25L12805D 16384KiB
Layer1 mtd0 mtd1 mtd2 mtd3 mtd4 mtd5
Size in KiB 256KiB 64KiB 1024KiB 14720KiB 256KiB 64KiB
Name u-boot u-boot-env kernel rootfs cfg EEPROM
mountpoint none none none / none none
filesystem none none none SquashFS 4.0 none none
Ubiquiti LiteBeam 5AC Gen2 Flash Layout
Layer0 m25p128 spi0.0: Macronix MX25L12805D 16384KiB
Layer1 mtd0 u-boot 256KiB mtd1 u-boot-env 64KiB mtd2 firmware 15744KiB mtd6 cfg 256 KiB mtd7 EEPROM 64KiB
Layer2 mtd3 kernel mtd4 rootfs
mountpoint /
filesystem overlayfs
Layer3 mtd5 rootfs_data
Size in KiB 256KiB 64KiB 256KiB 64KiB
Name u-boot u-boot-env kernel rootfs_data cfg EEPROM
mountpoint none none none /rom /overlay none none
filesystem none none none SquashFS JFFS2 none none

Ubiquiti LiteBeam 5AC Gen2 has the following buttons:

BUTTON Event
Reset reset

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters
for Ubiquiti LiteBeam 5AC Gen2
115200, 8N1

[ 0.000000] Linux version 2.6.32.68 (jenkins@9496cb8761c7) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 unknown) ) #1 Wed Apr 25 08:50:18 EEST 2018 [ 0.000000] flash_size passed from bootloader = 16 [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80295080, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs init=/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),1024k(kernel),14720k(rootfs),256k(cfg),64k(EEPROM) mem=64M panic=3 quiet [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61760k/65536k available (2128k kernel code, 3704k reserved, 513k data, 132k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] plat_time_init: plat time init done [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled [ 0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=133120) [ 0.022000] Mount-cache hash table entries: 512 [ 0.024000] NET: Registered protocol family 16 [ 0.026000] PCIe WLAN H/W found [tries: 1] [ 0.026000] PCI init:ath_pcibios_init [ 0.027000] ath_pcibios_init(419): PCI CMD write: 0x356 [ 0.027000] registering PCI controller with io_map_base unset [ 0.032000] bio: create slab <bio-0> at 0 [ 0.033000] pci 0000:00:00.0: reg 10 64bit mmio: [0x000000-0x1fffff] [ 0.034000] pci 0000:00:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] [ 0.034000] pci 0000:00:00.0: supports D1 D2 [ 0.034000] Returning IRQ 64 [ 0.035000] Switching to clocksource MIPS [ 0.037000] NET: Registered protocol family 2 [ 0.038000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.039000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.039000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.039000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.039000] TCP reno registered [ 0.040000] NET: Registered protocol family 1 [ 0.040000] ATH GPIOC major 0 [ 0.041000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.041000] msgmni has been set to 120 [ 0.042000] io scheduler noop registered (default) [ 0.066000] Serial: Atheros High-Speed UART (115200) [ 0.066000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.067000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A [ 0.067000] console [ttyS0] enabled [ 0.069000] 6 cmdlinepart partitions found on MTD device ath-nor0 [ 0.069000] Creating 6 MTD partitions on "ath-nor0": [ 0.069000] 0x000000000000-0x000000040000 : "u-boot" [ 0.070000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.071000] 0x000000050000-0x000000150000 : "kernel" [ 0.072000] 0x000000150000-0x000000fb0000 : "rootfs" [ 0.073000] mtd: partition "rootfs" set to be root filesystem [ 0.073000] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.075000] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.076000] u32 classifier [ 0.076000] Performance counters on [ 0.076000] input device check on [ 0.076000] Actions configured [ 0.078000] TCP westwood registered [ 0.078000] NET: Registered protocol family 10 [ 0.081000] NET: Registered protocol family 17 [ 0.081000] Bridge firewalling registered [ 0.081000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 0.081000] All bugs added by David S. Miller <davem@redhat.com> [ 0.081000] athwdt_init: Registering WDT success [ 0.082000] Reset: Normal [ 0.082000] ath_otp_init: Registering OTP success [ 0.082000] ath_clksw_init: Registering Clock Switch Interface success [ 0.089000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.090000] Freeing unused kernel memory: 132k freed [ 1.636000] ubnthal: module license 'Proprietary' taints kernel. [ 1.636000] Disabling lock debugging due to kernel taint [ 1.683000] ubnthal: initializing... [ 1.683000] ath-gpio 2.0 initialised [ 1.683000] ubnthal: initialised, board found, sysid = 0xe7f9, name = LiteBeam 5AC Gen2 [ 1.683000] ubnthal: host_board_t size: 7392B, boards table size: 166kB [ 6.901000] ATHR_GMAC: Length per segment 1536 [ 6.901000] ATHR_GMAC: fifo cfg 3 01f00140 [ 6.902000] Found PHY at address 4 with ID 4d:d072 [ 6.902000] Registering AR8035 Phy.... [ 6.902000] ATHR_GMAC: RX TASKLET - Pkts per Intr:160 [ 6.902000] ATHR_GMAC: Mac address for unit 0:bfff0000 [ 6.902000] ATHR_GMAC: b4:fb:e4:a5:88:74 [ 7.456000] ATHR_GMAC: Max segments per packet : 1 [ 7.456000] ATHR_GMAC: Max tx descriptor count : 128 [ 7.456000] ATHR_GMAC: Max rx descriptor count : 252 [ 7.456000] ATHR_GMAC: Mac capability flags : 42200 [ 7.568000] PPP generic driver version 2.4.2 [ 7.628000] PPP MPPE Compression module registered [ 7.661000] NET: Registered protocol family 24 [ 7.830000] GRE over IPv4 tunneling driver [ 7.947000] URD Init [ 8.398000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, 11D) [ 8.564000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 8.679000] ath_spectral: Version 2.0.0 [ 8.679000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 8.680000] SPECTRAL module built on Apr 25 2018 08:48:56 [ 8.947000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 10.867000] ath_pci: 10.1.467 (Atheros/multi-bss) [ 10.867000] Ubiquiti U-AME chipset detected [ 10.867000] ath_pci_probe [ 10.867000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 10.868000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x83b27a00 [ 10.868000] [ 10.868000] ol_ath_pci_configure : num_desired MSI set to 0 [ 10.868000] [ 10.868000] Using PCI Legacy Interrupt [ 10.980000] __ol_ath_attach: ath_attach TODO [ 10.981000] ol_ath_attach() BMI inited. [ 10.981000] ol_ath_attach() BMI Get Target Info. [ 10.981000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 10.982000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 10.982000] ol_ath_attach() configure Target . [ 10.982000] qc98xx_verify_checksum: flash checksum passed: 0x13b5 [ 10.982000] ol_transfer_bin_file 338: Download Flash data len 2116 [ 10.996000] BMI operation done [ 10.996000] ol_transfer_bin_file 259: Download Firmware data len 214160. Mode: PTP [ 11.905000] BMI operation done [ 11.905000] ol_ath_attach() Download FW. [ 11.905000] ol_ath_attach() HT Create . [ 11.905000] ol_ath_attach() HIF Claim. [ 11.905000] ol_ath_attach() BMI Done. [ 11.906000] ol_ath_attach() WMI attached. wmi_handle 83b70000 [ 11.906000] +HWT [ 11.909000] -HWT [ 11.909000] HTC Service:0x0300 ep:1 TX flow control disabled [ 11.914000] ol_txrx_pdev_attach: tx_credit initialised to 1424 [ 11.914000] HTC Service:0x0100 ep:2 TX flow control disabled [ 11.914000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 11.914000] num_rf_chain : 00000002 [ 11.914000] ht_cap_info: : 0000085b [ 11.914000] vht_cap_info : 338001b2 [ 11.914000] vht_supp_mcs : 0000fffa [ 11.923000] FIRMWARE:P 34 V 1 T 110 [ 11.923000] [ 11.923000] wmi_ready_event_rx: WMI UNIFIED READY event [ 11.924000] ol_ath_connect_htc() WMI is ready [ 11.924000] ol_ath_set_host_app_area TODO [ 11.924000] target uses HTT version 2.1; host uses 2.1 [ 11.924000] ol_ath_attach() connect HTC. [ 11.924000] Supported modes: 0x1f9001 [ 11.924000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 11.978000] ol_ath_phyerr_attach: called [ 11.979000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 11.985000] OL Resmgr Init-ed [ 11.986000] ol_if_spectral_setup [ 11.986000] SPECTRAL : get_capability not registered [ 11.986000] HAL_CAP_PHYDIAG : Capable [ 11.986000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 234) [ 11.986000] SPECTRAL : get_capability not registered [ 11.986000] HAL_CAP_RADAR : Capable [ 11.986000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 11.986000] (spectral_attach : 239) [ 11.986000] SPECTRAL : get_capability not registered [ 11.986000] HAL_CAP_SPECTRAL_SCAN : Capable [ 11.986000] SPECTRAL : get_tsf64 not registered [ 11.986000] spectral_init_netlink 54 NULL SKB [ 11.986000] ol_ath_set_dscp_tid_map: ...ath.c [ 11.986000] ol_if_dfs_setup: called [ 11.986000] ol_ath_rtt_meas_report_attach: called [ 11.986000] ol_ath_attach() UMAC attach . [ 11.986000] __ol_ath_attach: init tx/rx TODO [ 11.986000] __ol_ath_attach: hard_header_len reservation 64 [ 11.986000] __ol_ath_attach: dev name wifi0 [ 11.990000] ath_ahb: 10.1.467 (Atheros/multi-bss) [ 11.991000] __ath_attach: Set global_scn[0] [ 11.991000] ACBKMinfree = 48 [ 11.991000] ACBEMinfree = 32 [ 11.991000] ACVIMinfree = 16 [ 11.991000] ACVOMinfree = 0 [ 11.991000] CABMinfree = 48 [ 11.991000] UAPSDMinfree = 0 [ 12.001000] Enterprise mode: 0x00000000 [ 12.002000] Restoring Cal data from Flash [ 12.378000] SPECTRAL : get_capability not registered [ 12.378000] HAL_CAP_PHYDIAG : Capable [ 12.378000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 234) [ 12.378000] SPECTRAL : get_capability not registered [ 12.378000] HAL_CAP_RADAR : Capable [ 12.378000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 12.378000] (spectral_attach : 239) [ 12.378000] SPECTRAL : get_capability not registered [ 12.378000] HAL_CAP_SPECTRAL_SCAN : Capable [ 12.378000] SPECTRAL : get_tsf64 not registered [ 12.378000] spectral_init_netlink 54 NULL SKB [ 12.378000] IRQ request for SPECTRAL-XMIT-FILTER successful [ 12.378000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT [ 12.378000] SPECTRAL : module attached [ 12.382000] ath_get_caps[5784] rx chainmask mismatch actual 3 sc_chainmak 0 [ 12.382000] ath_get_caps[5759] tx chainmask mismatch actual 3 sc_chainmak 0 [ 12.383000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 12.415000] SPECTRAL : module already attached [ 12.417000] ath_tx_paprd_init sc 827a0000 PAPRD Enabled [ 12.702000] wifi1: Atheros 9340: mem=0xb8100000, irq=2 [ 12.927000] ubnt_poll_host: Hooks registered [ 12.927000] ubnt_poll_host: Allocated chardev region for major 189 [ 13.049000] rssi-leds 1.2 loaded [ 13.364000] Mirror/redirect action on [ 14.432000] ath_dfs: Version 2.0.0 [ 14.432000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 14.577000] ath92.ol_ath_set_config_param(): Reset scheduled on wifi0 radio [ 14.577000] Resetting the radio [ 14.577000] Suspending Target - with disable_intr set [ 14.577000] waiting for target paused event from target [ 14.580000] __ol_ath_detach: init tx/rx cleanup TODO [ 14.580000] ol_if_dfs_teardown: called [ 14.580000] ol_ath_phyerr_detach: called [ 14.583000] ol_if_spectral_detach [ 14.583000] SPECTRAL : Module removed (spectral = 83bfd000) [ 14.583000] ath_pci_warm_reset :(sc 83b27a00) [ 14.583000] Target Warm Reset [ 14.583000] Host Intr Cause reg 0x900c : value : 0x4000 [ 14.583000] Target CPU Intr Cause 0x5000 [ 14.683000] addr 0x4050 : 0x4 [ 14.703000] Target CPU Intr Cause after CE reset 0x0 [ 14.703000] RESET_CONTROL after cpu warm reset 0x800 [ 14.804000] Target Warm reset complete [ 14.804000] ath_pci_remove [ 14.804000] Ubiquiti U-AME chipset detected [ 14.804000] ath_pci_probe [ 14.804000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 14.804000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x83b27a00 [ 14.804000] [ 14.804000] ol_ath_pci_configure : num_desired MSI set to 0 [ 14.804000] [ 14.804000] Using PCI Legacy Interrupt [ 14.916000] __ol_ath_attach: ath_attach TODO [ 14.918000] ol_ath_attach() BMI inited. [ 14.923000] ol_ath_attach() BMI Get Target Info. [ 14.923000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 14.923000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 14.924000] ol_ath_attach() configure Target . [ 14.924000] qc98xx_verify_checksum: flash checksum passed: 0x13b5 [ 14.924000] ol_transfer_bin_file 338: Download Flash data len 2116 [ 14.938000] BMI operation done [ 14.938000] ol_transfer_bin_file 259: Download Firmware data len 214160. Mode: PTP [ 15.862000] BMI operation done [ 15.862000] ol_ath_attach() Download FW. [ 15.862000] ol_ath_attach() HT Create . [ 15.862000] ol_ath_attach() HIF Claim. [ 15.862000] ol_ath_attach() BMI Done. [ 15.863000] ol_ath_attach() WMI attached. wmi_handle 83b70000 [ 15.863000] +HWT [ 15.865000] -HWT [ 15.866000] HTC Service:0x0300 ep:1 TX flow control disabled [ 15.870000] ol_txrx_pdev_attach: tx_credit initialised to 1424 [ 15.870000] HTC Service:0x0100 ep:2 TX flow control disabled [ 15.871000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 15.871000] num_rf_chain : 00000002 [ 15.871000] ht_cap_info: : 0000085b [ 15.871000] vht_cap_info : 338001b2 [ 15.871000] vht_supp_mcs : 0000fffa [ 15.880000] FIRMWARE:P 34 V 1 T 110 [ 15.880000] [ 15.880000] wmi_ready_event_rx: WMI UNIFIED READY event [ 15.880000] ol_ath_connect_htc() WMI is ready [ 15.880000] ol_ath_set_host_app_area TODO [ 15.880000] ol_ath_attach() connect HTC. [ 15.880000] target uses HTT version 2.1; host uses 2.1 [ 15.880000] Supported modes: 0x1f9001 [ 15.880000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 15.935000] ol_ath_phyerr_attach: called [ 15.935000] ath92.ieee80211_ifattach(): Enable ignore 11d [ 15.942000] OL Resmgr Init-ed [ 15.942000] ol_if_spectral_setup [ 15.942000] SPECTRAL : get_capability not registered [ 15.942000] HAL_CAP_PHYDIAG : Capable [ 15.942000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 234) [ 15.942000] SPECTRAL : get_capability not registered [ 15.942000] HAL_CAP_RADAR : Capable [ 15.942000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 15.942000] (spectral_attach : 239) [ 15.942000] SPECTRAL : get_capability not registered [ 15.942000] HAL_CAP_SPECTRAL_SCAN : Capable [ 15.942000] SPECTRAL : get_tsf64 not registered [ 15.942000] spectral_init_netlink 54 NULL SKB [ 15.943000] ol_ath_set_dscp_tid_map: ...ath.c [ 15.943000] ol_if_dfs_setup: called [ 15.943000] ol_ath_rtt_meas_report_attach: called [ 15.943000] ol_ath_attach() UMAC attach . [ 15.943000] __ol_ath_attach: init tx/rx TODO [ 15.943000] __ol_ath_attach: hard_header_len reservation 64 [ 15.943000] __ol_ath_attach: dev name wifi0 [ 15.985000] Reset of radio done [ 15.985000] ubnt_poll_host: Hooks registered [ 15.985000] ubnt_poll_host: Allocated chardev region for major 189 [ 16.052000] ubnt_poll_host wifi0: Char device created succesfully err 0 [ 16.053000] ubnt_poll_host: Polling enabled for radio wifi0 [ 16.053000] ubnt_poll_host: noack_mode set to 0 for radio wifi0 [ 16.053000] ubnt_poll_host: DAPROT set to 0 for radio wifi0 [ 16.053000] ubnt-poll-host: [wifi0] Station priority configured to 2 (no-auto=0) [ 16.053000] ubnt_poll_host: Fixed frame mode disabled for radio wifi0 [ 16.194000] ath_ioctl: SIOC80211IFCREATE CALLED [ 16.194000] ubnt_poll_host: Initialized in PTP STA mode for device wifi0 [ 16.195000] wmi_unified_set_psmode:set psmode=1 [ 16.195000] ol_if_dfs_attach: called; ptr=83126ffc, radar_info=8322d908 [ 16.200000] ol_if_dfs_configure: called [ 16.200000] ol_if_dfs_configure: FCC domain [ 16.200000] ol_if_dfs_disable: called [ 16.200000] ol_ath_phyerr_disable: about to send [ 16.201000] VAP device ath0 created [ 16.231000] dfs_control debug flags now 0x00000003 [ 16.276000] BW divisor: 0X411 [ 16.369000] ath_dfs: another dfs module already in use [ 16.378000] wlan_vap_create : enter. devhandle=0x827902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 16.379000] wlan_vap_create : exit. devhandle=0x827902c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. [ 16.379000] VAP device ath1 created [ 16.390000] [ 16.390000] DES SSID SET=LBE-5AC-Gen2:B4FBE4A48874 [ 16.692000] Invoking ACS module for Best channel selection [ 16.903000] ubnt_poll_host: ATPC enabled (0/0/0/24) for radio wifi0 [ 17.010000] [ 17.010000] DES SSID SET=ubnt [ 17.020000] ol_ath_vap_set_param: VAP param unsupported param:33 value:0 [ 17.050000] wmi_unified_set_psmode:set psmode=0 [ 17.050000] wmi_unified_set_psmode:set psmode=0 [ 17.495000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 17.712000] Ebtables v2.0 registered [ 17.858000] xt_time: kernel timezone is -0000 [ 18.022000] nf_conntrack version 0.5.0 (968 buckets, 3872 max) [ 18.023000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 18.023000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 18.023000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 18.929000] ieee80211_acs_find_best_centerchan: ACS picked 2437 as best channel [ 19.236000] device eth0 entered promiscuous mode [ 19.248000] device ath0 entered promiscuous mode [ 19.261000] ath_paprd_cal sc 827a0000 chan_mask 3 PAPRD excessive failure disabling PAPRD now [ 19.405000] athr_gmac_ring_alloc Allocated 2048 at 0x81f4a800 [ 19.405000] sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000 [ 19.405000] athr_gmac_ring_alloc Allocated 4032 at 0x820e0000 [ 19.405000] sram_desc_cnt 4560,mac Unit 0,Rx r->ring_desc 0xbd000600 [ 19.705000] WASP ----> AR8035 PHY [ 19.706000] AR8035 Detected [ 19.706000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 19.706000] Setting PHY... [ 19.706000] Forced AR8035 PHY hardware reset on PHY setup. [ 19.819000] AR8035 - ID 0x004d:0xd072 [ 26.031000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 27.780000] br0: port 2(ath0) entering learning state [ 28.780000] br0: port 2(ath0) entering forwarding state


[ 0.000000] Linux version 4.14.118 (ubuntu@ubuntu) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10011-71ab2c9)) #0 Wed May 15 11:34:24 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is Ubiquiti LiteBeam AC Gen2 [ 0.000000] SoC: Atheros AR9342 rev 3 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 804cbf90, node_mem_map 81006f00 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 58540K/65536K available (3518K kernel code, 141K rwdata, 872K rodata, 1220K init, 201K bss, 6996K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 535.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns [ 0.000012] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns [ 0.008326] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.094953] pid_max: default: 32768 minimum: 301 [ 0.100094] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.107153] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.119302] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.129825] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.136409] pinctrl core: initialized pinctrl subsystem [ 0.143121] NET: Registered protocol family 16 [ 0.155791] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges: [ 0.162729] MEM 0x0000000010000000..0x0000000013ffffff [ 0.168293] IO 0x0000000000000000..0x0000000000000000 [ 0.192152] PCI host bridge to bus 0000:00 [ 0.196596] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.203909] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.209850] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.217071] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.225555] pci 0000:00:00.0: [0777:11ac] type 00 class 0x028000 [ 0.225621] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.225678] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.225764] pci 0000:00:00.0: supports D1 D2 [ 0.226008] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.226041] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.233841] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.244601] clocksource: Switched to clocksource MIPS [ 0.251213] NET: Registered protocol family 2 [ 0.256810] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.264250] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.271082] TCP: Hash tables configured (established 1024 bind 1024) [ 0.278026] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.284261] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.291304] NET: Registered protocol family 1 [ 0.296063] PCI: CLS 0 bytes, default 32 [ 0.299459] Crashlog allocated RAM at address 0x3f00000 [ 0.306594] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.319235] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.325497] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.346470] io scheduler noop registered [ 0.350652] io scheduler deadline registered (default) [ 0.358674] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68 [ 0.367263] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.374942] console [ttyS0] disabled [ 0.378796] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A [ 0.388029] console [ttyS0] enabled [ 0.395458] bootconsole [early0] disabled [ 0.416158] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.421355] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.427827] Creating 5 MTD partitions on "spi0.0": [ 0.432698] 0x000000000000-0x000000040000 : "u-boot" [ 0.438785] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.445195] 0x000000050000-0x000000fb0000 : "firmware" [ 0.453768] 2 uimage-fw partitions found on MTD device firmware [ 0.459838] Creating 2 MTD partitions on "firmware": [ 0.464899] 0x000000000000-0x000000180000 : "kernel" [ 0.470833] 0x000000180000-0x000000f60000 : "rootfs" [ 0.476805] mtd: device 4 (rootfs) set to be root filesystem [ 0.482588] 1 squashfs-split partitions found on MTD device rootfs [ 0.488928] 0x0000005d0000-0x000000f60000 : "rootfs_data" [ 0.495390] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.501062] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.508414] libphy: Fixed MDIO Bus: probed [ 0.856511] libphy: ag71xx_mdio: probed [ 0.954809] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:04 [uid=004dd072, driver=Atheros 8035 ethernet] [ 0.965855] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii [ 0.973329] NET: Registered protocol family 17 [ 0.978013] 8021q: 802.1Q VLAN Support v1.8 [ 0.989817] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.005013] Freeing unused kernel memory: 1220K [ 1.009611] This architecture does not have kernel memory protection. [ 1.716867] init: Console is alive [ 1.720589] init: - watchdog - [ 2.424644] random: fast init done [ 2.932216] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.069395] usbcore: registered new interface driver usbfs [ 3.075159] usbcore: registered new interface driver hub [ 3.080661] usbcore: registered new device driver usb [ 3.093404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.102102] ehci-platform: EHCI generic platform driver [ 3.108428] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.126367] init: - preinit - [ 4.523664] random: jshn: uninitialized urandom read (4 bytes read) [ 4.875012] random: jshn: uninitialized urandom read (4 bytes read) [ 4.921856] random: jshn: uninitialized urandom read (4 bytes read) [ 8.512920] jffs2: notice: (408) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (0 unchecked, 2 orphan) and 7 of xref (2 dead, 0 orphan) found. [ 8.530513] mount_root: switching to jffs2 overlay [ 8.562085] overlayfs: upper fs does not support tmpfile. [ 8.574308] urandom-seed: Seeding with /etc/urandom.seed [ 8.725811] procd: - early - [ 8.728868] procd: - watchdog - [ 9.454755] procd: - watchdog - [ 9.458302] procd: - ubus - [ 9.623584] urandom_read: 4 callbacks suppressed [ 9.623593] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.637040] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.644082] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.651833] procd: - init - [ 10.160454] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.171508] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7 [ 10.179259] Backport generated by backports.git v4.19.32-1-0-g1c4f7569 [ 10.196508] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 10.280616] xt_time: kernel timezone is -0000 [ 10.474877] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.531749] PPP generic driver version 2.4.2 [ 10.539265] NET: Registered protocol family 24 [ 10.581551] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 10.587529] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 10.869567] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 10.880479] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.077173] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 11.087888] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2 [ 11.098807] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.348875] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed [ 11.375196] ath10k_pci 0000:00:00.0: qca988x hw2.0 ubiquiti target 0x4100016c chip_id 0x043222ff sub 0777:e7f9 [ 11.385397] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 11.400308] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00043 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 ed0aafd8 [ 11.494908] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 [ 11.505553] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.683454] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 11.704240] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 12.851633] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 12.996812] ath: EEPROM regdomain: 0x0 [ 12.996821] ath: EEPROM indicates default country code should be used [ 12.996825] ath: doing EEPROM country->regdmn map search [ 12.996843] ath: country maps to regdmn code: 0x3a [ 12.996850] ath: Country alpha2 being used: US [ 12.996854] ath: Regpair used: 0x3a [ 13.165509] ath: phy1: disabling 5GHz band [ 13.170774] ath: EEPROM regdomain: 0x0 [ 13.170780] ath: EEPROM indicates default country code should be used [ 13.170784] ath: doing EEPROM country->regdmn map search [ 13.170802] ath: country maps to regdmn code: 0x3a [ 13.170809] ath: Country alpha2 being used: US [ 13.170814] ath: Regpair used: 0x3a [ 13.187652] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 13.189521] ieee80211 phy1: Atheros AR9340 Rev:3 mem=0xb8100000, irq=12 [ 13.200935] kmodloader: done loading kernel modules from /etc/modules.d/* [ 26.857758] br-lan: port 1(eth0) entered blocking state [ 26.863075] br-lan: port 1(eth0) entered disabled state [ 26.868761] device eth0 entered promiscuous mode [ 32.906003] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware [ 32.950174] br-lan: port 2(wlan0) entered blocking state [ 32.955650] br-lan: port 2(wlan0) entered disabled state [ 32.961396] device wlan0 entered promiscuous mode [ 34.079289] br-lan: port 2(wlan0) entered blocking state [ 34.084764] br-lan: port 2(wlan0) entered listening state [ 35.610933] br-lan: port 3(wlan0.sta1) entered blocking state [ 35.616843] br-lan: port 3(wlan0.sta1) entered disabled state [ 35.623013] device wlan0.sta1 entered promiscuous mode [ 35.651821] br-lan: port 3(wlan0.sta1) entered blocking state [ 35.657734] br-lan: port 3(wlan0.sta1) entered listening state [ 36.114646] br-lan: port 2(wlan0) entered learning state [ 37.714627] br-lan: port 3(wlan0.sta1) entered learning state [ 38.194637] br-lan: port 2(wlan0) entered forwarding state [ 38.200220] br-lan: topology change detected, sending tcn bpdu [ 39.794628] br-lan: port 3(wlan0.sta1) entered forwarding state [ 39.800650] br-lan: topology change detected, sending tcn bpdu


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1