Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:trendnet:tew-732br [2016/02/02 18:59] – danitool | toh:trendnet:tew-732br [2018/04/28 11:00] – Datatables added, cleanup tmomas | ||
|---|---|---|---|
| Line 2: | Line 2: | ||
| Basic N300 Wireless Router | Basic N300 Wireless Router | ||
| - | |||
| - | Supported since [[https:// | ||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| - | ^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version | + | ---- datatable ---- |
| - | | v1.0 | 2013-02 | - | Barrier Breaker | + | cols : Brand, |
| + | headers : Brand, | ||
| + | align | ||
| + | filter | ||
| + | ---- | ||
| ===== Hardware Highlights ===== | ===== Hardware Highlights ===== | ||
| - | ^ SoC ^ Ram | + | ---- datatable ---- |
| - | | Atheros AR9341 | + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, |
| + | header | ||
| + | align | ||
| + | filter | ||
| + | ---- | ||
| - | Manufacturer' | ||
| ===== Installation ===== | ===== Installation ===== | ||
| - | | + | ---- datatable ---- |
| - | - → [[doc:howto: | + | cols |
| - | - → **»»»»here»»»»[[about/ | + | headers |
| + | align : l,c,c | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | -> [[docs:guide-user: | ||
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | | FIXME Please check out the article [[doc:techref:Flash.Layout]]. It contains an example and a couple of explanations. | | + | | FIXME Please check out the article [[docs:techref:flash.layout]]. It contains an example and a couple of explanations. | |
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| Line 38: | Line 50: | ||
| ==== Upgrading OpenWrt ==== | ==== Upgrading OpenWrt ==== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | ||
| Line 68: | Line 80: | ||
| ===== Basic configuration ===== | ===== Basic configuration ===== | ||
| - | -> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\ | + | -> [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]] After flashing, proceed with this.\\ |
| Set up your Internet connection, configure wireless | Set up your Internet connection, configure wireless | ||
| Line 93: | Line 105: | ||
| ==== Failsafe mode ==== | ==== Failsafe mode ==== | ||
| - | -> [[doc:howto:generic.failsafe]] | + | -> [[docs:guide-user:troubleshooting: |
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| The TRENDnet TEW-732BR has two buttons. They are Reset and WPS. Here, we merely name the buttons, so we can use them in the above Howto: | The TRENDnet TEW-732BR has two buttons. They are Reset and WPS. Here, we merely name the buttons, so we can use them in the above Howto: | ||
| Line 108: | Line 120: | ||
| | **[[wp> | | **[[wp> | ||
| | **Vendor: | | **Vendor: | ||
| - | | **[[doc:techref:Bootloader]]:** | [[doc: | + | | **[[docs:techref:bootloader]]:** | [[docs: |
| - | | **[[doc: | + | | **[[docs: |
| - | | **[[doc: | + | | **[[docs: |
| | **Flash size: | | **Flash size: | ||
| | **Flash Chip: | | **Flash Chip: | ||
| Line 116: | Line 128: | ||
| | **RAM Chip: | | **RAM Chip: | ||
| | **Wireless No1: | | **Wireless No1: | ||
| - | | **[[doc:hardware:Switch]]:** | // | + | | **[[docs: |
| - | | **[[doc/hardware/internet.access.technologies|Modem]]: | + | | **[[docs: |
| | **USB: | | **USB: | ||
| - | | **[[doc: | + | | **[[docs: |
| - | | **[[doc: | + | | **[[docs: |
| ==== Photos ==== | ==== Photos ==== | ||
| Line 145: | Line 157: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the Serial Port of this specific device: | How to connect to the Serial Port of this specific device: | ||
| Line 152: | Line 164: | ||
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the JTAG Port of this specific device: | How to connect to the JTAG Port of this specific device: | ||
| Line 160: | Line 172: | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| ===== Bootlogs ===== | ===== Bootlogs ===== | ||