Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:trendnet:tew-691gr [2015/03/16 17:05] – Added original firmware boot log erwan574toh:trendnet:tew-691gr [2018/04/28 10:50] – Datatables added, cleanup tmomas
Line 1: Line 1:
 +====== Trendnet TEW-691GR ======
  
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid
 +headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,c,c,c,c,c,c
 +filter  : Model=TEW-691GR
 +----
 +
 +
 +===== Hardware Highlights =====
 +---- datatable ----
 +cols    : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_
 +header  : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB
 +align   : c,c,c,c,c,c,c,c,c,c,c,c,c
 +filter  : Model=TEW-691GR
 +----
 +
 +
 +===== Installation =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock
 +align   : l,c,c
 +filter  : Model=TEW-691GR
 +----
 +
 +-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
 +
 +FIXME Please add the installation procedure here.
 +
 +===== Hardware =====
 +==== Serial ====
 +UART pinout:\\
 +{{:media:trendnet:tew-691gr.jpg?400|}}
 +
 +
 +===== Bootlogs =====
 +==== OEM bootlog ====
 +
 +<WRAP bootlog>
 +<nowiki>U-Boot 1.1.3 (Sep 29 2010 - 10:49:55)
 +
 +
 +Board: Ralink APSoC DRAM:  64 MB
 +
 +relocate_code Pointer at: 83fac000
 +
 +
 + Set info->start[0]=BC000000
 +
 +flash_protect ON: from 0xBC000000 to 0xBC01F2EB
 +
 +flash_protect ON: from 0xBC030000 to 0xBC030FFF
 +
 +*** Warning - bad CRC, using default environment
 +
 +
 +============================================ 
 +
 +Ralink UBoot Version: 3.4.0.0
 +
 +-------------------------------------------- 
 +
 +ASIC 3883_MP (MAC to VITESSE Mode)
 +
 +DRAM component: 512 Mbits DDR, width 16
 +
 +DRAM bus: 16 bit
 +
 +Total memory: 64 MBytes
 +
 +Flash component: NOR Flash
 +
 +Date:Sep 29 2010  Time:10:49:55
 +
 +============================================ 
 +
 +icache: sets:512, ways:4, linesz:32 ,total:65536
 +
 +dcache: sets:256, ways:4, linesz:32 ,total:32768 
 +
 +
 + ##### The CPU freq = 480 MHZ #### 
 +
 +
 + SDRAM bus set to 32 bit 
 +
 + SDRAM size =64 Mbytes
 +
 +
 +Please choose the operation: 
 +
 +   1: Load system code to SDRAM via TFTP. 
 +
 +   2: Load system code then write to Flash via TFTP. 
 +
 +   3: Boot system code via Flash (default).
 +
 +   4: Entr boot command line interface.
 +
 +   7: Load Boot Loader code then write to Flash via Serial. 
 +
 +   9: Load Boot Loader code then write to Flash via TFTP. 
 +
 + 4  3  2  1  0 
 +
 +   
 +
 +3: System Boot system code via Flash.
 +
 +## Booting image at bc050000 ...
 +
 +   Image Name:   Linux Kernel Image
 +
 +   Created:      2013-11-14   5:22:30 UTC
 +
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +
 +   Data Size:    3860621 Bytes =  3.7 MB
 +
 +   Load Address: 80000000
 +
 +   Entry Point:  802f9000
 +
 +   Verifying Checksum ... OK
 +
 +   Uncompressing Kernel Image ... OK
 +
 +No initrd
 +
 +## Transferring control to Linux (at address 802f9000) ...
 +
 +## Giving linux memsize in MB, 64
 +
 +
 +Starting kernel ...
 +
 +
 +
 +LINUX started...
 +
 + THIS IS ASIC
 +Linux version 2.6.21 (tom.hung@fedora17) (gcc version 3.4.2) #2 Thu Nov 14 13:22:22 CST 2013
 +
 + The CPU frequency set to 480 MHz
 +CPU revision is: 0001974c
 +Determined physical RAM map:
 + memory: 04000000 @ 00000000 (usable)
 +Initrd not found or empty - disabling initrd
 +Built 1 zonelists.  Total pages: 16256
 +Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
 +Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, linesize 32 bytes.
 +Synthesized TLB refill handler (20 instructions).
 +Synthesized TLB load handler fastpath (32 instructions).
 +Synthesized TLB store handler fastpath (32 instructions).
 +Synthesized TLB modify handler fastpath (31 instructions).
 +cause = 40808000, status = 11000000
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +calculating r4koff... 001d4c00(1920000)
 +CPU frequency 480.00 MHz
 +Using 240.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 58860k/65536k available (2343k kernel code, 6612k reserved, 696k data, 2808k init, 0k highmem)
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +SCSI subsystem initialized
 +NET: Registered protocol family 2
 +Time: MIPS clocksource has been installed.
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +detected lzma initramfs
 +detected lzma initramfs
 +initramfs: LZMA lc=3,lp=0,pb=2,dictSize=1048576,origSize=12480000
 +LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com>...............................................................................................................................................................................................<5>ralink flash device: 0x1000000 at 0x1c000000
 +Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 + Amd/Fujitsu Extended Query Table at 0x0040
 +Ralink SoC physically mapped flash: Swapping erase regions for broken CFI table.
 +number of CFI chips: 1
 +cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
 +Creating 5 MTD partitions on "Ralink SoC physically mapped flash":
 +0x00000000-0x00400000 : "ALL"
 +0x00000000-0x00030000 : "Bootloader"
 +0x00030000-0x00040000 : "Config"
 +0x00040000-0x00050000 : "Factory"
 +0x00050000-0x01000000 : "Kernel"
 +mtd: partition "Kernel" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x3b0000
 +squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
 +squashfs: LZMA suppport for slax.org by jro
 +io scheduler noop registered (default)
 +====== GPIO Mode: 0x1811 ======
 +Ralink gpio driver initialized
 +spidrv_major = 217
 +i2cdrv_major = 218
 +HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
 +N_HDLC line discipline registered.
 +Serial: 8250/16550 driver $Revision: 1.8 $ 2 ports, IRQ sharing disabled
 +serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
 +serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
 +RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
 +loop: loaded (max 8 devices)
 +Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
 +MAC_ADRH -- : 0x0000d8eb
 +MAC_ADRL -- : 0x97a640b0
 +PROC INIT OK!
 +IMQ starting with 2 devices...
 +IMQ driver loaded successfully.
 + Hooking IMQ after NAT on PREROUTING.
 + Hooking IMQ before NAT on POSTROUTING.
 +PPP generic driver version 2.4.2
 +PPP BSD Compression module registered
 +NET: Registered protocol family 24
 +block2mtd: version $Revision: 1.1.1.1 $
 +Netfilter messages via NETLINK v0.30.
 +nf_conntrack version 0.5.0 (512 buckets, 4096 max)
 +nf_conntrack_rtsp v0.03 loading
 +match connlimit register
 +PPTP driver version 0.8.5
 +GRE over IPv4 demultiplexor driver<6>gre: can't add protocol
 +ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
 +arp_tables: (C) 2002 David S. Miller
 +TCP cubic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 10
 +IPv6 over IPv4 tunneling driver
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +Freeing unused kernel memory: 2808k freed
 +
 +init started: BusyBox v1.12.1 (Algorithmics/MIPS FPU Emulator v1.5
 +2013-11-14 11:41:19 CST)
 +
 +starting pid 612, ttydevpts: called with bogus options
 + '': '/etc_ro/rcS'
 +mount: mounting none on /proc/bus/usb failed: No such file or directory
 +Welcome to
 +     _______  _______  ___     __  ____    _   ___
 +    |  ___  \|   __  ||     |__||    \ | || | /  /
 +    | |___| ||  |__| ||   |__  __ |     \| || |/  /
 +    |     /    ||      ||  || |\     ||     \
 +    |__| \__\|__| |__||______||__||_| \____||_|\___\
 +
 +                 =System Architecture Department=
 +
 +flash error, file size too large!
 +no config file to read, put it first.
 +Erasing mtd failed
 +Erasing mtd failed
 +Erasing mtd failed
 +Create a message queue in goahead for interprocess communication!! 
 +ifconfig ra0 down
 +ifconfig: ioctl 0x8913 failed: No such device
 +ifconfig ra1 down
 +ifconfig: ioctl 0x8913 failed: No such device
 +ifconfig ra2 down
 +ifconfig: ioctl 0x8913 failed: No such device
 +ifconfig ra3 down
 +ifconfig: ioctl 0x8913 failed: No such device
 +rmmod rt2860v2_ap
 +rmmod: rt2860v2_ap: No such file or directory
 +ralink_init make_wireless_config rt2860
 +Jan  1 00:00:05 crond[653]: crond (busybox 1.12.1) started, log level 8
 +
 +
 +insmod rt2860v2_ap
 +rt2860v2_ap: module license 'unspecified' taints kernel.
 +
 +
 +=== pAd = c005c000, size = 671912 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +ifconfig ra0 up
 +RX DESC a331b000  size = 2048
 +
 +starting pid 695, tty '/dev/ttyS1': '/bin/sh'
 +
 +
 +BusyBox v1.12.1 (2013-11-14 11:41:19 CST) built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +# Key1Str is Invalid key length(0) or Type(0)
 +Key2Str is Invalid key length(0) or Type(0)
 +Key3Str is Invalid key length(0) or Type(0)
 +Key4Str is Invalid key length(0) or Type(0)
 +1. Phy Mode = 9
 +2. Phy Mode = 9
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +3. Phy Mode = 9
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +MCS Set = ff ff ff 00 01
 +SYNC - BBP R4 to 20MHz.l
 +[: 3200: unknown operand
 +Main bssid = d8:eb:97:a6:40:b0
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +ifconfig ra1 up
 +ifconfig: ioctl 0x8913 failed: No such device
 +ifconfig ra2 up
 +ifconfig: ioctl 0x8913 failed: No such device
 +ifconfig ra3 up
 +ifconfig: ioctl 0x8913 failed: No such device
 +brctl addif br0 ra0
 +brctl: bridge br0: No such device
 +brctl addif br0 ra1
 +brctl: iface ra1: No such device
 +brctl addif br0 ra2
 +brctl: iface ra2: No such device
 +brctl addif br0 ra3
 +brctl: iface ra3: No such device
 +First time initInternet, detect dip switch status: On
 +internet.sh
 +0
 +chpasswd: an error occurred updating password for admin
 +rmmod: ralink_wdt: No such file or directory
 +rmmod: cls: No such file or directory
 +rmmod: hw_nat: No such file or directory
 +rmmod: raeth: No such file or directory
 +brctl: iface apcli0: No such device
 +ifconfig: ioctl 0x8913 failed: No such device
 +
 +phy_tx_ring = 0x00323000, tx_ring = 0xa0323000
 +
 +phy_rx_ring0 = 0x00324000, rx_ring0 = 0xa0324000
 +Initing AR8316
 +phyUnit=1,phyBase=0,phyAddr=1,phyHwStatus =0x10
 +0x03=d041
 +eth0: Phy Specific Status=0010
 +phyUnit=2,phyBase=0,phyAddr=2,phyHwStatus =0x10
 +0x03=d041
 +eth0: Phy Specific Status=0010
 +phyUnit=3,phyBase=0,phyAddr=3,phyHwStatus =0x10
 +0x03=d041
 +eth0: Phy Specific Status=0010
 +phyUnit=4,phyBase=0,phyAddr=4,phyHwStatus =0x10
 +0x03=d041
 +eth0: Phy Specific Status=0010
 +phyUnit=5,phyBase=0,phyAddr=32,phyHwStatus =0x10
 +0x03=d041
 +eth0: Phy Specific Status=0010
 +Calling athrs16_reg_init
 +athrs16_reg_init VLAN Setup complete.
 +Livelinks=0
 +No PHYs found...
 +MAC_ADRH -- : 0x0000d8eb
 +MAC_ADRL -- : 0x97a640b0
 +CDMA_CSG_CFG = 81000007
 +GDMA1_FWD_CFG = C0710000
 +acm_msg> ACM_MEM_Alloc_Num = 1
 +acm_msg> ACM_MEM_Free_Num  = 1
 +
 +##### disable 1st wireless interface #####
 +rmmod: rt2860v2_ap_net: No such file or directory
 +RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
 +rmmod: rt2860v2_ap_util: No such file or directory
 +rmmod: rt2860v2_sta_net: No such file or directory
 +rmmod: rt2860v2_sta: No such file or directory
 +rmmod: rt2860v2_sta_util: No such file or directory
 +insmod: rt2860v2_ap_util.ko: module not found
 +
 +
 +=== pAd = c005c000, size = 671912 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +insmod: rt2860v2_ap_net.ko: module not found
 +rmmod: nf_nat_pptp: No such file or directory
 +rmmod: nf_conntrack_pptp: No such file or directory
 +rmmod: nf_nat_proto_gre: No such file or directory
 +rmmod: nf_conntrack_proto_gre: No such file or directory
 +RX DESC a04e7000  size = 2048
 +Key1Str is Invalid key length(0) or Type(0)
 +Key2Str is Invalid key length(0) or Type(0)
 +Key3Str is Invalid key length(0) or Type(0)
 +Key4Str is Invalid key length(0) or Type(0)
 +1. Phy Mode = 9
 +2. Phy Mode = 9
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +3. Phy Mode = 9
 +RTMPSetPhyMode: channel is out of range, use first channel=0 
 +MCS Set = ff ff ff 00 01
 +SYNC - BBP R4 to 20MHz.l
 +Main bssid = d8:eb:97:a6:40:b0
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +vconfig: ioctl error for rem: Invalid argument
 +vconfig: ioctl error for rem: Invalid argument
 +rmmod: 8021q: No such file or directory
 +insmod: 8021q.ko: module not found
 +eth2.2    Link encap:Ethernet  HWaddr D8:EB:97:A6:40:B0  
 +ifconfig: ioctl 0x8913 failed: No such device
 +brctl: bridge br0: No such device
 +brctl: bridge br0: No such device
 +EntryLifeCheck Cnt = 1024.
 +device ra0 entered promiscuous mode
 +brctl: bridge br0: Device or resource busy
 +eth2.1: dev_set_promiscuity(master, 1)
 +device eth2 entered promiscuous mode
 +device eth2.1 entered promiscuous mode
 +Raise 1.2v voltage of RT3883 to 1.21v (PLL and RF)  for improve TEW-691GR low throughput issue or crash issue
 +ra0       rf:
 +R20[0x14]:44
 +
 +eth2.2: Setting MAC address to  d8 eb 97 a6 40 b0.
 +VLAN (eth2.2):  Underlying device (eth2) has same MAC, not checking promiscious mode.
 +eth2.2: Setting MAC address to  d8 eb 97 a6 40 b3.
 +killall: config-chat.sh: no process killed
 +udhcpc (v1.12.1) started
 +br0: port 2(eth2.1) entering learning state
 +br0: port 1(ra0) entering learning state
 +ifconfig: ioctl 0x8914 failed: Cannot assign requested address
 +ifconfig: ioctl 0x8914 failed: Cannot assign requested address
 +
 +***** g_wl_interface = ra0 ******
 +
 +############ Show current upstream interface and IP address for igmpproxy ############
 +upstream interface: eth2.2
 +IP address:
 +          inet6 addr: fe80::daeb:97ff:fea6:40b3/64 Scope:Link
 +
 +iptables: No chain/target/match by that name
 +igmpproxy, Version 0.1 beta2, Build 131114 
 +Copyright 2005 by Johnny Egeland <johnny@rlo.org>
 +Distributed under the GNU GENERAL PUBLIC LICENSE, Version 2 - check GPL.txt
 +
 +Warn: Warning, No upstream interface assigned.
 +iptables: No chain/target/match by that name
 +iptables: No chain/target/match by that name
 +route: ioctl 0x890c failed: No such process
 +Start UPnP: upnpd
 +check: eth2.2 br0
 +libupnp: using UDP SSDP_PORT = 1900
 +DHCP Server start initial
 +br0: topology change detected, propagating
 +br0: port 2(eth2.1) entering forwarding state
 +br0: topology change detected, propagating
 +br0: port 1(ra0) entering forwarding state
 +killall: udhcpd: no process killed
 +****** Running ipv6Lan.sh ******
 +[RunSystemCmd 93] ipv6Lan.sh
 +############ Running ipv6Lan.sh ############
 +killall: dhcp6s: no process killed
 +############ End of ipv6Lan.sh ############
 +[init_ipv6 797] ###### init IPv6 ######
 +[RunSystemCmd 93] mkdir /var/db/
 +[init_ipv6 821] ###### Reset WAN IPv6 ######
 +[init_ipv6 849] v6TunIf_old=
 +[RunSystemCmd 93] echo 1 > /proc/sys/net/ipv6/conf/eth2.2/autoconf
 +[set_DNS 681] ######  Set DNS ######
 +[RunSystemCmd 93] echo -n > /etc/wanv6_resolv.conf 
 +[RunSystemCmd 93] echo -n > /etc/wan_resolv.conf 
 +[RunSystemCmd 93] echo 1 > /proc/sys/net/ipv6/conf/all/forwarding
 +[RunSystemCmd 93] ipv6Lan.sh
 +############ Running ipv6Lan.sh ############
 +killall: dhcp6s: no process killed
 +############ End of ipv6Lan.sh ############
 +iptables: No chain/target/match by that name
 +Enable Implicit and Explicit Tx Beamforming for TEW-691GR
 +Configure predefined URL to: "tew-691gr.trendnet"
 +DHCP Server start initial
 +0xB0=0xCC36CC36
 +0xB4=0xCA36CA36
 +0xB8=0xC936C936
 +send_event: Sent firewall reload message to goahead!
 +/sbin/ant_div.sh: line 18: can't create /proc/AntDiv/AD_ALGORITHM: nonexistent directory
 +/sbin/ant_div.sh: line 18: can't create /proc/AntDiv/AD_RUN: nonexistent directory
 +killall rt2860apd 1>/dev/null 2>&1
 +killall rt2860apd 1>/dev/null 2>&1
 +ntp.sh
 +ddns.sh
 +kill -9 `cat /var/run/wscd.pid.ra0`
 +iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
 +iwpriv ra0 set WscConfMode=7
 +iwpriv ra0 set WscConfStatus=1
 +route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1
 +wscd -m 1 -a 192.168.10.1 -i ra0 &
 +libupnp: using UDP SSDP_PORT = 1900
 +setup-wizard.sh
 +/sbin/setup-wizard.sh: line 12: setup-wizard: not found
 +getBoardID
 +BoardID: 026910
 +killall -q klogd
 +killall -q syslogd
 +syslogd -C8 1>/dev/null 2>&1
 +klogd 1>/dev/null 2>&1
 +/bin/qos_run
 +webs: Listening for HTTP requests at address 192.168.10.1
 +iwpriv ra0 set WscAPLock=1
 +goahead: local script rc.local
 +Adding multicast routing
 +Limit Ping of Death
 +Start RFW daemon
 +bind policy ipv4
 +send_event: Sent firewall reload message to goahead!
 +iptables -t nat -D PREROUTING -i eth2.2 -j TRIGGER --trigger-type dnat
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -i eth2.2  -j TRIGGER --trigger-type dnat
 +iptables -t nat -D PREROUTING -i ppp0 -j TRIGGER --trigger-type dnat
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -i ppp0  -j TRIGGER --trigger-type dnat
 +There is not any static route be set up!
 +Password for 'umedia' changed
 +lang_free: Don't need release multi-lang mapping again.
 +lang_init: File /etc_ro/web/lang/STRINGS_EN.txt open fail!
 +goahead.c: multi-lang init fail.
 +goahead: Get message from send_event, the message is firewall_reload
 +goahead: start firewall_init()
 +echo 0 > /proc/sys/net/ipv4/ip_forward
 +iptables -F -t filter 1>/dev/null 2>&1
 +iptables -D FORWARD -j macipport_block  1>/dev/null 2>&1
 +iptables -F macipport_block  1>/dev/null 2>&1
 +iptables -t mangle -F POSTROUTING_ALG
 +iptables: No chain/target/match by that name
 +iptables -P INPUT ACCEPT
 +iptables -P OUTPUT ACCEPT
 +iptables -P FORWARD ACCEPT
 +iptables -F INPUT_SPort
 +iptables: No chain/target/match by that name
 +iptables -F FORWARD_SPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_SPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -F POSTROUTING_SPort
 +iptables: No chain/target/match by that name
 +iptables -F INPUT_MPort
 +iptables: No chain/target/match by that name
 +iptables -F FORWARD_MPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_MPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -F POSTROUTING_MPort
 +iptables: No chain/target/match by that name
 +iptables -F INPUT_AC
 +iptables: No chain/target/match by that name
 +iptables -F FORWARD_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F POSTROUTING_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_DMZ
 +iptables: No chain/target/match by that name
 +iptables -t nat -F POSTROUTING_DMZ
 +iptables: No chain/target/match by that name
 +iptables -t nat -F POSTROUTING
 +iptables -t nat -F PREROUTING
 +iptables -t nat -F PREROUTING_ICMP
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_UPnP
 +iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
 +iptables -I PREROUTING -t nat -i eth2.2 -s 0.0.0.0/0 -p udp -m state --state NEW -j DROP
 +iptables -I PREROUTING -t nat -i eth2.2 -p tcp --syn -j DROP
 +iptables -I PREROUTING -t nat -i eth2.2 -s 0.0.0.0/0 -p udp --sport 520 -j ACCEPT
 +iptables -I PREROUTING -t nat -i eth2.2 -s 0.0.0.0/0 -p tcp -m state --state RELATED,ESTABLISHED -j ACCEPT
 +iptables -t nat -D PREROUTING -i eth2.2 -j TRIGGER --trigger-type dnat
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -i eth2.2  -j TRIGGER --trigger-type dnat
 +iptables -t nat -D PREROUTING -i ppp0 -j TRIGGER --trigger-type dnat
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -i ppp0  -j TRIGGER --trigger-type dnat
 +iptables -t nat -N POSTROUTING_NAT
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_NAT
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_NAT
 +iptables -t nat -N POSTROUTING_DNS
 +iptables -t nat -D POSTROUTING -j POSTROUTING_DNS
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_DNS
 +iptables -t nat -F POSTROUTING_DNS
 +iptables -t nat -N PREROUTING_ICMP
 +iptables -t nat -D PREROUTING -j PREROUTING_ICMP
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_ICMP
 +iptables -t nat -F PREROUTING_ICMP
 +iptables -I PREROUTING_ICMP -t nat -i eth2.2 -s 0.0.0.0/0 -p icmp --icmp-type echo-request -j DROP
 +iptables -t nat -N PREROUTING_DMZ
 +iptables -t nat -D PREROUTING -j PREROUTING_DMZ
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_DMZ
 +iptables -t nat -N POSTROUTING_DMZ
 +iptables -t nat -D POSTROUTING -j POSTROUTING_DMZ
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_DMZ
 +iptables -t filter -N web_filter 1>/dev/null 2>&1
 +iptables -t filter -D FORWARD -j web_filter 1>/dev/null 2>&1
 +iptables -t filter -I FORWARD -j web_filter 1>/dev/null 2>&1
 +iptables -t filter -N ip_range_block 1>/dev/null 2>&1
 +iptables -t filter -D FORWARD -j ip_range_block 1>/dev/null 2>&1
 +iptables -t filter -I FORWARD -j ip_range_block 1>/dev/null 2>&1
 +iptables -D FORWARD -j FORWARD_UPnP
 +iptables: No chain/target/match by that name
 +iptables -I FORWARD -j FORWARD_UPnP
 +iptables -t nat -D PREROUTING -j PREROUTING_UPnP
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_UPnP
 +iptables -N INPUT_SPort
 +iptables -D INPUT -j INPUT_SPort
 +iptables: No chain/target/match by that name
 +iptables -I INPUT -j INPUT_SPort
 +iptables -N FORWARD_SPort
 +iptables -D FORWARD -j FORWARD_SPort
 +iptables: No chain/target/match by that name
 +iptables -I FORWARD -j FORWARD_SPort
 +iptables -N INPUT_MPort
 +iptables -D INPUT -j INPUT_MPort
 +iptables: No chain/target/match by that name
 +iptables -I INPUT -j INPUT_MPort
 +iptables -N FORWARD_MPort
 +iptables -D FORWARD -j FORWARD_MPort
 +iptables: No chain/target/match by that name
 +iptables -I FORWARD -j FORWARD_MPort
 +iptables -t nat -N PREROUTING_SPort
 +iptables -t nat -D PREROUTING -j PREROUTING_SPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_SPort
 +iptables -t nat -N POSTROUTING_SPort
 +iptables -t nat -D POSTROUTING -j POSTROUTING_SPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_SPort
 +iptables -t nat -N PREROUTING_MPort
 +iptables -t nat -D PREROUTING -j PREROUTING_MPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_MPort
 +iptables -t nat -N POSTROUTING_MPort
 +iptables -t nat -D POSTROUTING -j POSTROUTING_MPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_MPort
 +iptables -t nat -N PREROUTING_AC
 +iptables -t nat -D PREROUTING -j PREROUTING_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_AC
 +iptables -t nat -N PREROUTING_Remote
 +iptables -t nat -D PREROUTING -j PREROUTING_Remote
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_Remote
 +iptables -t nat -N POSTROUTING_Remote
 +iptables -t nat -D POSTROUTING -j POSTROUTING_Remote
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_Remote
 +iptables -t mangle -N POSTROUTING_ALG
 +iptables -t mangle -D POSTROUTING -j POSTROUTING_ALG
 +iptables: No chain/target/match by that name
 +iptables -t mangle -I POSTROUTING -j POSTROUTING_ALG
 +iptables -t nat -N PREROUTING_IGMP
 +iptables -t nat -D PREROUTING -j PREROUTING_IGMP
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_IGMP
 +iptables -t filter -F web_filter
 +iptables -t filter -F ip_range_block
 +Can't get wan ip address!!
 +iptables -A FORWARD -p 1 -j ACCEPT
 +iptables -A FORWARD -p 47 -j ACCEPT
 +iptables -A FORWARD -p 50 -j ACCEPT
 +iptables -A FORWARD -p 51 -j ACCEPT
 +iptables -A FORWARD -p 6 -j ACCEPT
 +iptables -A FORWARD -p 17 -j ACCEPT
 +iptables -A INPUT -j DROP -p tcp --sport 0
 +iptables -A INPUT -j DROP -p udp --sport 0
 +iptables -A INPUT -j DROP -p tcp --dport 0
 +iptables -A INPUT -j DROP -p udp --dport 0 
 +iptables -A INPUT -j DROP -p tcp --sport 1
 +iptables -A INPUT -j DROP -p udp --sport 1
 +iptables -A INPUT -j DROP -p tcp --dport 1
 +iptables -A INPUT -j DROP -p udp --dport 1
 +iptables -A INPUT -p tcp -j ACCEPT
 +iptables -A INPUT -p udp -j ACCEPT
 +iptables -F INPUT_SPort
 +iptables -F FORWARD_SPort
 +iptables -t nat -F PREROUTING_SPort
 +iptables -t nat -F POSTROUTING_SPort
 +iptables -F INPUT_MPort
 +iptables -F FORWARD_MPort
 +iptables -t nat -F PREROUTING_MPort
 +iptables -t nat -F POSTROUTING_MPort
 +iptables -F INPUT_AC
 +iptables: No chain/target/match by that name
 +iptables -F FORWARD_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_AC
 +iptables -t nat -F POSTROUTING_AC
 +iptables: No chain/target/match by that name
 +kill `ps |grep 'crond'|grep -v 'grep'|awk '{print $1}'`
 +crond
 +iptables -t nat -I PREROUTING_AC -p tcp --dport 80 -s 192.168.10.1/255.255.255.0 -d 192.168.10.1 -j ACCEPT
 +echo 1 > /proc/sys/net/ipv4/ip_forward
 +echo 1 > /proc/sys/net/nf_conntrack_flush
 +echo 7200 > /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established
 +killall -q zebra
 +killall -q ripd
 +ntp.sh
 +goahead: Get message from send_event, the message is firewall_reload
 +goahead: start firewall_init()
 +echo 0 > /proc/sys/net/ipv4/ip_forward
 +iptables -F -t filter 1>/dev/null 2>&1
 +iptables -D FORWARD -j macipport_block  1>/dev/null 2>&1
 +iptables -F macipport_block  1>/dev/null 2>&1
 +iptables -t mangle -F POSTROUTING_ALG
 +iptables -P INPUT ACCEPT
 +iptables -P OUTPUT ACCEPT
 +iptables -P FORWARD ACCEPT
 +iptables -F INPUT_SPort
 +iptables -F FORWARD_SPort
 +iptables -t nat -F PREROUTING_SPort
 +iptables -t nat -F POSTROUTING_SPort
 +iptables -F INPUT_MPort
 +iptables -F FORWARD_MPort
 +iptables -t nat -F PREROUTING_MPort
 +iptables -t nat -F POSTROUTING_MPort
 +iptables -F INPUT_AC
 +iptables: No chain/target/match by that name
 +iptables -F FORWARD_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_AC
 +iptables -t nat -F POSTROUTING_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_DMZ
 +iptables -t nat -F POSTROUTING_DMZ
 +iptables -t nat -F POSTROUTING
 +iptables -t nat -F PREROUTING
 +iptables -t nat -F PREROUTING_ICMP
 +iptables -t nat -F PREROUTING_UPnP
 +iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
 +iptables -I PREROUTING -t nat -i eth2.2 -s 0.0.0.0/0 -p udp -m state --state NEW -j DROP
 +iptables -I PREROUTING -t nat -i eth2.2 -p tcp --syn -j DROP
 +iptables -I PREROUTING -t nat -i eth2.2 -s 0.0.0.0/0 -p udp --sport 520 -j ACCEPT
 +iptables -I PREROUTING -t nat -i eth2.2 -s 0.0.0.0/0 -p tcp -m state --state RELATED,ESTABLISHED -j ACCEPT
 +iptables -t nat -D PREROUTING -i eth2.2 -j TRIGGER --trigger-type dnat
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -i eth2.2  -j TRIGGER --trigger-type dnat
 +iptables -t nat -D PREROUTING -i ppp0 -j TRIGGER --trigger-type dnat
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -i ppp0  -j TRIGGER --trigger-type dnat
 +iptables -t nat -N POSTROUTING_NAT
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_NAT
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_NAT
 +iptables -t nat -N POSTROUTING_DNS
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_DNS
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_DNS
 +iptables -t nat -F POSTROUTING_DNS
 +iptables -t nat -N PREROUTING_ICMP
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_ICMP
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_ICMP
 +iptables -t nat -F PREROUTING_ICMP
 +iptables -I PREROUTING_ICMP -t nat -i eth2.2 -s 0.0.0.0/0 -p icmp --icmp-type echo-request -j DROP
 +iptables -t nat -N PREROUTING_DMZ
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_DMZ
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_DMZ
 +iptables -t nat -N POSTROUTING_DMZ
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_DMZ
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_DMZ
 +iptables -t filter -N web_filter 1>/dev/null 2>&1
 +iptables -t filter -D FORWARD -j web_filter 1>/dev/null 2>&1
 +iptables -t filter -I FORWARD -j web_filter 1>/dev/null 2>&1
 +iptables -t filter -N ip_range_block 1>/dev/null 2>&1
 +iptables -t filter -D FORWARD -j ip_range_block 1>/dev/null 2>&1
 +iptables -t filter -I FORWARD -j ip_range_block 1>/dev/null 2>&1
 +iptables -D FORWARD -j FORWARD_UPnP
 +iptables: No chain/target/match by that name
 +iptables -I FORWARD -j FORWARD_UPnP
 +iptables -t nat -D PREROUTING -j PREROUTING_UPnP
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_UPnP
 +iptables -N INPUT_SPort
 +iptables: Chain already exists
 +iptables -D INPUT -j INPUT_SPort
 +iptables: No chain/target/match by that name
 +iptables -I INPUT -j INPUT_SPort
 +iptables -N FORWARD_SPort
 +iptables: Chain already exists
 +iptables -D FORWARD -j FORWARD_SPort
 +iptables: No chain/target/match by that name
 +iptables -I FORWARD -j FORWARD_SPort
 +iptables -N INPUT_MPort
 +iptables: Chain already exists
 +iptables -D INPUT -j INPUT_MPort
 +iptables: No chain/target/match by that name
 +iptables -I INPUT -j INPUT_MPort
 +iptables -N FORWARD_MPort
 +iptables: Chain already exists
 +iptables -D FORWARD -j FORWARD_MPort
 +iptables: No chain/target/match by that name
 +iptables -I FORWARD -j FORWARD_MPort
 +iptables -t nat -N PREROUTING_SPort
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_SPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_SPort
 +iptables -t nat -N POSTROUTING_SPort
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_SPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_SPort
 +iptables -t nat -N PREROUTING_MPort
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_MPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_MPort
 +iptables -t nat -N POSTROUTING_MPort
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_MPort
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_MPort
 +iptables -t nat -N PREROUTING_AC
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_AC
 +iptables -t nat -N PREROUTING_Remote
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_Remote
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_Remote
 +iptables -t nat -N POSTROUTING_Remote
 +iptables: Chain already exists
 +iptables -t nat -D POSTROUTING -j POSTROUTING_Remote
 +iptables: No chain/target/match by that name
 +iptables -t nat -I POSTROUTING -j POSTROUTING_Remote
 +iptables -t mangle -N POSTROUTING_ALG
 +iptables: Chain already exists
 +iptables -t mangle -D POSTROUTING -j POSTROUTING_ALG
 +iptables -t mangle -I POSTROUTING -j POSTROUTING_ALG
 +iptables -t nat -N PREROUTING_IGMP
 +iptables: Chain already exists
 +iptables -t nat -D PREROUTING -j PREROUTING_IGMP
 +iptables: No chain/target/match by that name
 +iptables -t nat -I PREROUTING -j PREROUTING_IGMP
 +iptables -t filter -F web_filter
 +iptables -t filter -F ip_range_block
 +Can't get wan ip address!!
 +iptables -A FORWARD -p 1 -j ACCEPT
 +iptables -A FORWARD -p 47 -j ACCEPT
 +iptables -A FORWARD -p 50 -j ACCEPT
 +iptables -A FORWARD -p 51 -j ACCEPT
 +iptables -A FORWARD -p 6 -j ACCEPT
 +iptables -A FORWARD -p 17 -j ACCEPT
 +iptables -A INPUT -j DROP -p tcp --sport 0
 +iptables -A INPUT -j DROP -p udp --sport 0
 +iptables -A INPUT -j DROP -p tcp --dport 0
 +iptables -A INPUT -j DROP -p udp --dport 0 
 +iptables -A INPUT -j DROP -p tcp --sport 1
 +iptables -A INPUT -j DROP -p udp --sport 1
 +iptables -A INPUT -j DROP -p tcp --dport 1
 +iptables -A INPUT -j DROP -p udp --dport 1
 +iptables -A INPUT -p tcp -j ACCEPT
 +iptables -A INPUT -p udp -j ACCEPT
 +iptables -F INPUT_SPort
 +iptables -F FORWARD_SPort
 +iptables -t nat -F PREROUTING_SPort
 +iptables -t nat -F POSTROUTING_SPort
 +iptables -F INPUT_MPort
 +iptables -F FORWARD_MPort
 +iptables -t nat -F PREROUTING_MPort
 +iptables -t nat -F POSTROUTING_MPort
 +iptables -F INPUT_AC
 +iptables: No chain/target/match by that name
 +iptables -F FORWARD_AC
 +iptables: No chain/target/match by that name
 +iptables -t nat -F PREROUTING_AC
 +iptables -t nat -F POSTROUTING_AC
 +iptables: No chain/target/match by that name
 +kill `ps |grep 'crond'|grep -v 'grep'|awk '{print $1}'`
 +crond
 +iptables -t nat -I PREROUTING_AC -p tcp --dport 80 -s 192.168.10.1/255.255.255.0 -d 192.168.10.1 -j ACCEPT
 +echo 1 > /proc/sys/net/ipv4/ip_forward
 +echo 1 > /proc/sys/net/nf_conntrack_flush
 +echo 7200 > /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established
 +killall -q zebra
 +killall -q ripd
 +ntp.sh
 +Start System Deamon
 +Clear connection track table</nowiki>
 +</WRAP>\\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>RT3883 8flash 64ram}}
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1