This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram. DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version (18.06 or later) onto it! See 4/32 warning for details.
1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.
2) OpenWrt support for this device will end after 2019.
19.07 will be the last official build for 4/32 devices. After 19.07, no further OpenWrt images will be built for 4/32 devices. See OpenWrt on 4/32 devices what you can do now.
The TP-Link WR940N is identical to the TL-WR941ND except that the antennas are not detachable and the hardware version is different. Only for WR940N v4 there seems to be no WR941ND-equivalent, yet.
Version v6.1 can be treated like v6, except for flashing via TFTP (see below).
Support for OpenWrt 19.07
Starting with version 19.07.4 OpenWrt supports these routers with the new target ath79-tiny, but standard images will be too large. However, you can build own images using the respective ImageBuilder. For instance, to build an image for TL-WR940N-V6 including LuCI and excluding PPP use the following command, see detailed instructions under build your own image:
Wait until the LED changes color, then release the reset button
The TFTP server should log the firmware file having been downloaded - if not, just keep trying
Once the file has been downloaded successfully, give it a minute or too, then try to get an IP address via DHCP
In case TFTP does not work, you'll have to attach a serial cable (see below). Serial login for stock firmware: root:sohoadmin
Note the serial port on the right part of the board, approx. in the middle. Four pins next to the two large capacitors.
The serial port pinout is TX, RX, GND, NC. (RX/TX might be swapped, I don't trust my usb-serial converter)
Port settings are 115200, 8n1, no flow control.
Note: The console output may have garbage characters in it, as well as it will not take input. In this case pulling TX high with a 15K resistor from 3.3 volt resolves this
With 8M SPI flash mod, 64MB RAM mod(NT5DS32M16BG-6K)
Note: At least in v4.0 serial port uses lower voltage levels (3.3V), so regular serial adapters might not work correctly (even with added pullup-resistor). Use LVTTL USB to Serial adapter instead. The old Nokia CA-42 connector works fine (swap RX/TX between board and adapter), or use adapter based on PL2303HX chip.
Serial console login: root:sohoadmin
Debug output v1
Some debug output below on a WR940N v1.0 flashed via openwrt-ar71xx-tl-wr941nd-v4-squashfs-factory.bin image (MD5 d753155844ad30db6906781083192d1e). Note that it says WR741ND?!
system type : Atheros AR7240 rev 2
machine : TP-LINK TL-WR741ND
processor : 0
cpu model : MIPS 24Kc V7.4
BogoMIPS : 266.24
wait instruction : yes
microsecond timers : yes
tlb_entries : 16
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x05f8, 0x0180, 0x0118]
ASEs implemented : mips16
shadow register sets : 1
core : 0
VCED exceptions : not available
VCEI exceptions : not available
toh/tp-link/tl-wr940n.txt · Last modified: 2020/09/13 09:15 by humaita