This is an old revision of the document!
TP-Link TL-WR802N v4
Supported Versions
Hardware Highlights
| Model | Version | SoC | CPU MHz | Flash MB | RAM MB | WLAN Hardware | WLAN2.4 | WLAN5.0 | 100M ports | Gbit ports | Modem | USB |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TL-WR802N | v4 | MediaTek MT7628N | 580 | 8 | 64 | MediaTek MT7628N | b/g/n | - | 1 | - | - |
Installation
The only way to flash the image in TL-WR802N v4 is to use tftp recovery mode in U-Boot:
- Configure PC with static IP 192.168.0.225/24 and tftp server. Alternate server IP address that worked for me was 192.168.0.66
- Download a tfpt server application. For windows “tftp 32” works. For Mac “Pumpkin” was the easiest method for me.
- Choose the default (root) directory for your server.
- Rename
openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bintotp_recovery.binand place it in tftp server directory. - Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 10 seconds, until device starts downloading the file. Pumpkin on Mac by default will prompt for approval for the file transfer.
- Router will download file from server, write it to flash and reboot. The reboot process takes a couple of minutes. The light on the device will cycle through various patterns as it updates.
- When the light on the device settles on solid it should be fully rebooted.
- You can now set your computer to receive a DHCP address and login to the web GUI at 192.168.1.1
Energy consumption
This device uses 1.3 watts at idle with OpenWRT and 4 SSIDs configured. Measured with high accuracy ELV Energy master.
Wireless hardware details
Up to 4 SSIDs are supported, maximum transmit power is 25 dBm (country code AU). IEEE 802.1Q VLANs are supported.
Output of iw phy for all
Wiphy phy0 wiphy index: 0 max # scan SSIDs: 4 max scan IEs length: 2257 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Device supports T-DLS. Available Antennas: TX 0x3 RX 0x3 Configured Antennas: TX 0x3 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * monitor * mesh point * P2P-client * P2P-GO Band 1: Capabilities: 0x1fe HT20/HT40 SM Power Save disabled RX Greenfield RX HT20 SGI RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: No restriction (0x00) HT TX/RX MCS rate indexes supported: 0-15 Frequencies: * 2412 MHz [1] (25.0 dBm) * 2417 MHz [2] (25.0 dBm) * 2422 MHz [3] (25.0 dBm) * 2427 MHz [4] (25.0 dBm) * 2432 MHz [5] (25.0 dBm) * 2437 MHz [6] (25.0 dBm) * 2442 MHz [7] (25.0 dBm) * 2447 MHz [8] (25.0 dBm) * 2452 MHz [9] (25.0 dBm) * 2457 MHz [10] (25.0 dBm) * 2462 MHz [11] (25.0 dBm) * 2467 MHz [12] (25.0 dBm) * 2472 MHz [13] (25.0 dBm) * 2484 MHz [14] (disabled) valid interface combinations: * #{ IBSS } <= 1, #{ managed, AP, mesh point, P2P-client, P2P-GO } <= 4, total <= 4, #channels <= 1, STA/AP BI must match HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Supported extended features: * [ RRM ]: RRM * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211 * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs * [ AIRTIME_FAIRNESS ]: airtime fairness scheduling * [ AQL ]: Airtime Queue Limits (AQL) * [ SCAN_RANDOM_SN ]: use random sequence numbers in scans * [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support * [ DEL_IBSS_STA ]: deletion of IBSS station support * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support</nowiki>