TP-Link RE650 v1
The TP-Link RE650 is a dual-band 4×4 MIMO 802.11a/n/ac (5GHz)/4×4 MIMO 802.11b/g/n (2.4GHz) “range extender” with a single Gigabit Ethernet port, powered by an internal power supply. As usual with range extenders the whole unit is designed to be plugged directly into a wall outlet.
Supported Versions
The TP-Link RE650 has been produced in two revisions, “1.0” and “2.0” (labeled “v1” and “v2” by OpenWrt). The revisions are easily distinguishable by the label on the device: it states “1.0” or “2.0” next to the region code. Hardware-wise the revisions are largely identical, the main difference being the v2 revision only offering half of the flash memory (8 MB vs. 16 MB).
For now, this TOH page only deals with the v1 revision, the v2 revision has its own TOH page.
Hardware Highlights
Installation
Installation via OEM web interface
- set your PC to a static IP in the 192.168.0.x range (e.g. 192.168.0.2)
- connect your PC to the ethernet port on the side of the unit
- open the web interface at http://192.168.0.254/
- navigate the web interface to Settings > System Tools > Firmware Upgrade
- for good measure, compare the revision (i.e., “1.0” for v1) is shown as “Hardware Version”
- upload the OpenWrt
factory.bin
image and confirm
The flashing process takes about 90 seconds, the first boot of OpenWrt will take a minute, subsequent boots are much faster. You can now reset your PC's IP address to DHCP or a static 192.168.1.x address and, as is common, access OpenWrt on the device at 192.168.1.1
.
Flash Layout
Find out flash layout, then add the flash layout table here (copy, paste, modify the example).
Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.
Upgrading OpenWrt
These are generic instructions. Update with your router's specifics.
LuCI Web Upgrade Process
- Browse to
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/
LuCI Upgrade URL - Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
sysupgrade
mtd
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
mtd
If sysupgrade
does not support this router, use mtd
.
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot
Debricking
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Please fill in real values for this device, then remove the EXAMPLEs
Network interfaces
The default network configuration is:
Interface Name | Description | Default configuration |
---|---|---|
br-lan | EXAMPLE LAN & WiFi | EXAMPLE 192.168.1.1/24 |
vlan0 (eth0.0) | EXAMPLE LAN ports (1 to 4) | EXAMPLE None |
vlan1 (eth0.1) | EXAMPLE WAN port | EXAMPLE DHCP |
wl0 | EXAMPLE WiFi | EXAMPLE Disabled |
Switch Ports (for VLANs)
Please fill in real values for this device, then remove the EXAMPLEs
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
Port | Switch port |
---|---|
Internet (WAN) | EXAMPLE 4 |
LAN 1 | EXAMPLE 3 |
LAN 2 | EXAMPLE 2 |
LAN 3 | EXAMPLE 1 |
LAN 4 | EXAMPLE 0 |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
Please fill in real values for this device, then remove the EXAMPLEs
The TP-Link RE650 has the following buttons:
BUTTON | Event |
---|---|
EXAMPLE Reset | reset |
EXAMPLE Secure Easy Setup | ses |
EXAMPLE No buttons at all. | - |
Hardware
Info
Photos
Front:
Insert photo of front of the casing
Back:
Insert photo of back of the casing
Backside label:
Insert photo of backside label
Opening the case
Note: This will void your warranty!
Remove the 4 T6 screws in the back side of the device and pry with a spudger along the front border of the case (prying along the back border will reveal the psu connector and the heat sink, that is held in place by three phillips screws on the other side of the motherboard).
The serial port connector and the spi flash chip are on the front side and there's no need to remove the heat sink or remove the main board from the case to reach them.
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Serial connection parameters for TP-Link RE650 v1 | 57600, 8N1 |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootloader mods
Hardware mods
None so far.
Bootlogs
OEM bootlog
=================================================================== MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11000000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x7, 1/0 = 608/416 1D000000 PLL4 FB_DL: 0x12, 1/0 = 636/388 49000000 PLL2 FB_DL: 0x1c, 1/0 = 553/471 71000000 do DDR setting..[01F40000] Apply DDR3 Setting...(use default AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 opt_dle value:8 DRAMC_R0DELDLY[018]=00001D1E ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 7 6 7 10 6 7 7 5 4 6 10 | 7 7 8 8 6 9 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =30 DQS1 = 29 ================================================================== bit DQS0 bit DQS1 0 (1~56)28 8 (1~56)28 1 (1~55)28 9 (1~55)28 2 (1~57)29 10 (1~58)29 3 (1~60)30 11 (1~56)28 4 (1~57)29 12 (1~58)29 5 (1~57)29 13 (1~56)28 6 (1~58)29 14 (0~58)29 7 (1~58)29 15 (1~57)29 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 9 8 8 10 7 8 8 6 5 7 10 | 7 8 8 9 6 9 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff3000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 DQS loop = 14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=500000000 HZ BUS=166666666 HZ =================================================================== U-Boot 1.1.3 (Jul 19 2018 - 10:08:42) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb8000 Config XHCI 40M PLL flash manufacture id: ef, device id 40 18 find flash: W25Q128BV *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Jul 19 2018 Time:10:08:42 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 gpioMode Reg: 0x4852c Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bfc20000 ... text base: 80001000 entry point: 804b8ac0 Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 804b8ac0) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 3.10.14 (lin@lin) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Thu Jul 19 10:12:54 CST 2018 The CPU feqenuce set to 880 MHz GCMP present CPU0 revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Zone ranges: Normal [mem 0x00000000-0x07ffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x07ffffff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 8 pages/cpu @81103000 s10496 r8192 d14080 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Writing ErrCtl register=0006246a Readback ErrCtl register=0006246a Memory: 121020k/131072k available (4872k kernel code, 10052k reserved, 2712k data, 344k init, 0k highmem) Hierarchical RCU implementation. NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 ftrace: allocating 14002 entries in 28 pages launch: starting cpu1 launch: cpu1 gone! CPU1 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! CPU2 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! CPU3 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 3: done. Brought up 4 CPUs NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 SCSI subsystem initialized PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60200000 res[1]->end = 6020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60210000 res[1]->end = 6021ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60100000 res[0]->end = 601fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 1, 8192 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 236 io scheduler noop registered (default) reg_int_mask=0, INT_MASK= 0 HSDMA_init hsdma_phy_tx_ring0 = 0x07ddc000, hsdma_tx_ring0 = 0xa7ddc000 hsdma_phy_rx_ring0 = 0x07de0000, hsdma_rx_ring0 = 0xa7de0000 TX_CTX_IDX0 = 0 TX_DTX_IDX0 = 0 RX_CRX_IDX0 = 3ff RX_DRX_IDX0 = 0 set_fe_HSDMA_glo_cfg HSDMA_GLO_CFG = 465 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A TP-LINK gpio driver initialized brd: module loaded flash manufacture id: ef, device id 40 18 W25Q128BV(ef 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 5 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000020000 : "fs-uboot" 0x000000020000-0x000000310000 : "os-image" 0x000000310000-0x000000e00000 : "file-system" 0x000000ff0000-0x000001000000 : "radio" register mt_drv === pAd = c0181000, size = 2329768 === <-- RTMPAllocAdapterBlock, Status=0 pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 1st iPAeLNA default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8747e408,8747e408 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8747e418,8747e418 <-- RTMPAllocTxRxRingMemory, Status=0 === pAd = c0501000, size = 2329768 === <-- RTMPAllocAdapterBlock, Status=0 pAd->PciHif.CSRBaseAddress =0xc0400000, csr_addr=0xc0400000! RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 2nd iPAeLNA default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 870b6308,870b6308 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 870b6318,870b6318 <-- RTMPAllocTxRxRingMemory, Status=0 rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x432880c3 Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x4328808a PROC INIT OK! TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 344K (8076a000 - 807c0000) init started: BusyBox v1.19.4 (2018-07-19 10:13:07 CST) starting pid 48, tty '': '/etc/rc.d/rcS' mkdir: can't create directory '/dev/pts': File exists This Board use 3.10.14.x Set: phy[0].reg[0] = 3900 Lan Domain: tplinkrepeater.net Lan Domain: www.tplinkrepeater.net 0: 0:FFFFFFD8:FFFFFFBA: 5:FFFFFF80 Raeth v3.1 (Tasklet) set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0x6e2c000!!! phy_free_tail_phy is 0x6e2dff0!!! txd_pool=a6e30000 phy_txd_pool=06E30000 ei_local->skb_free start address is 0x872226dc. free_txd: 06e30010, ei_local->cpu_ptr: 06E30000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa6e30000 0x06E30000 0x06E30000 phy_qrx_ring = 0x06e2b000, qrx_ring = 0xa6e2b000 phy_rx_ring0 = 0x06e3c000, rx_ring0 = 0xa6e3c000 MT7530 Reset Completed!! change HW-TRAP to 0x17ccf set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x4328808a CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 device eth2 entered promiscuous mode br0: port 1(eth2) entered forwarding state br0: port 1(eth2) entered forwarding state [ucEthernet_init:128]ERROR product_id= 06500100 ====>>>>caldata: 76 15 76 15 ====>>>>default mac is 98-da-c4-5f-5d-7d ====>>>>default mac is 98-da-c4-5f-5d-7d [daemonize:357]recv a pipe message. [main:581]send a pipe message. wifid[mtk_init_platform:2678]: success: init wifi config wifid[wifi_exec_cmd:1548]: mkdir -p /tmp/Wireless/RT2860 wifid[wifi_exec_cmd:1548]: cp /etc_ro/Wireless/RT2860/RT2860.dat /tmp/Wireless/RT2860/RT2860.dat [smartip_get_wifi_update_eth_bridge_status 514] open /tmp/wifi_update_eth_and_bridge file failed wifid[wifi_exec_cmd:1548]: mkdir -p /tmp/Wireless/iNIC wifid[wifi_exec_cmd:1548]: cp /etc_ro/Wireless/iNIC/iNIC_ap.dat /tmp/Wireless/iNtplink: try to open! IC/iNIC_ap.dat wifid[mtk_init_platform:2687]: success: get wifi config wifid[wifi_exec_cmd:1548]: ifconfig eth2 down ra2880stop()...Done Free TX/RX Ring Memory! br0: port 1(eth2) entered disabled state wifid[wifi_exec_cmd:1548]: ifconfig eth2 hw ether 98:DA:C4:5F:5D:7D wifid[wifi_exec_cmd:1548] 0: 0:FFFFFFD8:FFFFFFBA: 5:FFFFFF80 : ifconfig eth2 Raeth v3.1 (up Tasklet) set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0x6da4000!!! phy_free_tail_phy is 0x6da5ff0!!! txd_pool=a6da8000 phy_txd_pool=06DA8000 ei_local->skb_free start address is 0x872226dc. free_txd: 06da8010, ei_local->cpu_ptr: 06DA8000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa6da8000 0x06DA8000 0x06DA8000 phy_qrx_ring = 0x06da3000, qrx_ring = 0xa6da3000 phy_rx_ring0 = 0x068c0000, rx_ring0 = 0xa68c0000 MT7530 Reset Completed!! change HW-TRAP to 0x17ccf set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x000098da GMAC1_MAC_ADRL -- : 0xc45f5d7d CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 br0: port 1(eth2) entered forwarding state br0: port 1(eth2) entered forwarding state wifid[wifi_exec_cmd:1548]: ifconfig br0 down br0: port 1(eth2) entered disabled state wifid[wifi_exec_cmd:1548]: ifconfig br0 hw ether 98:DA:C4:5F:5D:7D wifid[wifi_exec_cmd:1548]:br0: port 1(eth2) entered forwarding state ifconfig br0 upbr0: port 1(eth2) entered forwarding state wifid[wifi_exec_cmd:1548]: switch_config.sh 1 wifid[mtk_init_platform:2697]: success: update eth and bridge wifid[mtk_init_platform:2700]DriverOwn()::Return since already in Driver Own... E2pAccessMode=2 wireless driver wifid[wifi_SSID[0]=RE650_ORIGIN_SSID_2G, EdcaIdx=0 exec_cmd:1548]: RTMPSetProfileParameters(): DBDC Mode=0 ifconfig ra0 up cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=1 APSDCapable[1]=1 APSDCapable[2]=1 APSDCapable[3]=1 APSDCapable[4]=1 APSDCapable[5]=1 APSDCapable[6]=1 APSDCapable[7]=1 APSDCapable[8]=1 APSDCapable[9]=1 APSDCapable[10]=1 APSDCapable[11]=1 APSDCapable[12]=1 APSDCapable[13]=1 APSDCapable[14]=1 APSDCapable[15]=1 default ApCliAPSDCapable[0]=1 default ApCliAPSDCapable[1]=1 AutoChannelSkipList[0]= 12 AutoChannelSkipList[1]= 13 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: Ext Channel = ABOVE WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125 Top Init Done! Use alloc_skb RX[0] DESC a75de000 size = 8192 RX[1] DESC a75e0000 size = 8192 Hif Init Done! ctl->txq = c03b7e54 ctl->rxq = c03b7e60 ctl->ackq = c03b7e6c ctl->kickq = c03b7e78 ctl->tx_doneq = c03b7e84 ctl->rx_doneq = c03b7e90 mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2401): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(3150) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20160419154809a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(452344) Build Date:_201704281731 Build Date:_201704281731 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201607011611 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! tplink: pAd->infType 5 efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::forceMode: 2 , infType: 5 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 0 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] tplink: pAd->EEPROMImage: c01ae9d2tplink: RtmpFlashRead c01ae9d2 from offset 0 tplink: eeFlashId 7615 Country Region from e2p = 1 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 rtmp_read_txpwr_from_eeprom(224): Don't Support this now! RTMPReadTxPwrPerRate(1381): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=8747f444,Band=0,rfcap=3,channel=1,PhyMode=2 MtCmdSetDbdcCtrl:(ret = 0) Band Rf: 1, Phy Mode: 2 AntCfgInit(2632): Not support for HIF_MT yet! auska: buffer 16384 MtSingleSkuLoadParam: RF_LOCKDOWN Feature ON !!! tplink: region is DE tplink: load sku 2, type is CE start ch = 1, ch->num = 14 Band: 0 Channel: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CCK: 26 26 OFDM: 26 26 26 26 26 VHT20: 26 26 26 26 26 26 26 VHT40: 26 26 26 26 26 26 26 VHT80: 0 0 0 0 0 0 0 VHT160: 0 0 0 0 0 0 0 PwrTxStreamDelta: 0 0 0 PwrTxNSSDelta: 0 0 0 0 start ch = 184, ch->num = 22 Band: 1 Channel: 184 188 192 196 8 12 16 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 CCK: 0 0 OFDM: 30 30 30 30 30 VHT20: 30 30 30 30 30 30 30 VHT40: 30 30 30 30 30 30 30 VHT80: 30 30 30 30 30 30 30 VHT160: 30 30 30 30 30 30 30 PwrTxStreamDelta: 0 0 0 PwrTxNSSDelta: 0 0 0 0 start ch = 96, ch->num = 22 Band: 1 Channel: 96 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173 177 181 CCK: 0 0 OFDM: 38 38 36 34 32 VHT20: 38 38 36 34 32 30 30 VHT40: 38 38 36 34 32 30 30 VHT80: 38 38 36 34 32 30 30 VHT160: 38 38 36 34 32 30 30 PwrTxStreamDelta: 0 0 0 PwrTxNSSDelta: 0 0 0 0 MtBfBackOffLoadTable: RF_LOCKDOWN Feature ON !!! MtBfBackOffLoadTable: BFBackoff Table index = 0 start ch = 1, ch->num = 14 Band: 0 Channel: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Max Power: 0 0 0 start ch = 184, ch->num = 44 Band: 1 Channel: 184 188 192 196 8 12 16 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173 177 181 Max Power: 0 0 0 EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2715): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1288): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! wdev_attr_update(): wdevId0 = 98:da:c4:5f:5d:7e MtCmdSetDbdcCtrl:(ret = 0) asuka: Channel=2, wdev->channel=2 CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 14 channels ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp<----------------- MtAsicSetChBusyStat(840): Not support for HIF_MT yet! [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 14 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 [RadarStateCheck]Set into RD_NORMAL_MODE bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY mt7615_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=2, HT-CentCh=2, VHT-CentCh=0 MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 BW = 1,TXStream = 4, RXStream = 4, scan(0) :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 2(Prim=2, HT-CentCh=2, VHT-CentCh=0, BBP_BW=1) [WrapDfsRadarDetectStart]: Band0Ch is 2[WrapDfsRadarDetectStart]: Band1Ch is 0MtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2573): Not support for HIF_MT yet! Main bssid = 98:da:c4:5f:5d:7e AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) MCS Set = ff ff ff ff 01 MtCmdSetMacTxRx:(ret = 0) <==== mt_wifi_init, Status=0 WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. Generate UUID for apidx(0) UUID: c01b3278, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 98 da c4 5f 5d 7e wifid[wifi_exec_cmd:1548]: brctl addif br0 ra0 device ra0 entered promiscuous mode br0: port 2(ra0) entered forwarding state br0: port 2(ra0) entered forwarding state MtCmdSetDbdcCtrl:(ret = 0) ifconfig apcli0 up asuka: Channel=2, wdev->channel=2 wifid[wifi_exec_cmd:1548]: brctl addif br0 apcli0 device apcli0 entered promiscuous mode br0: port 3(apcli0) entered forwarding state br0: port 3(apcli0) entered forwarding state wifid[wifi_exec_cmd:1548]: ifconfig rai0 up DriverOwn()::Return since already in Driver Own... E2pAccessMode=2 SSID[0]=RE650_ORIGIN_SSID_5G, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Equal! APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=1 APSDCapable[1]=1 APSDCapable[2]=1 APSDCapable[3]=1 APSDCapable[4]=1 APSDCapable[5]=1 APSDCapable[6]=1 APSDCapable[7]=1 APSDCapable[8]=1 APSDCapable[9]=1 APSDCapable[10]=1 APSDCapable[11]=1 APSDCapable[12]=1 APSDCapable[13]=1 APSDCapable[14]=1 APSDCapable[15]=1 default ApCliAPSDCapable[0]=1 default ApCliAPSDCapable[1]=1 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: Ext Channel = ABOVE WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125 Top Init Done! Use alloc_skb RX[0] DESC a721a000 size = 8192 RX[1] DESC a721c000 size = 8192 Hif Init Done! ctl->txq = c0737e54 ctl->rxq = c0737e60 ctl->ackq = c0737e6c ctl->kickq = c0737e78 ctl->tx_doneq = c0737e84 ctl->rx_doneq = c0737e90 mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2401): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(3150) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20160419154809a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(452344) Build Date:_201704281731 Build Date:_201704281731 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201607011611 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! tplink: pAd->infType 5 efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::forceMode: 2 , infType: 5 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 0 NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000] tplink: pAd->EEPROMImage: c052e9d2tplink: RtmpFlashRead c052e9d2 from offset 32768 tplink: eeFlashId 7615 Country Region from e2p = 1 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 rtmp_read_txpwr_from_eeprom(224): Don't Support this now! RTMPReadTxPwrPerRate(1381): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=870b7444,Band=0,rfcap=3,channel=1,PhyMode=2 MtCmdSetDbdcCtrl:(ret = 0) Band Rf: 1, Phy Mode: 2 AntCfgInit(2632): Not support for HIF_MT yet! auska: buffer 16384 MtSingleSkuLoadParam: RF_LOCKDOWN Feature ON !!! tplink: region is DE tplink: load sku 2, type is CE start ch = 1, ch->num = 14 Band: 0 Channel: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CCK: 26 26 OFDM: 26 26 26 26 26 VHT20: 26 26 26 26 26 26 26 VHT40: 26 26 26 26 26 26 26 VHT80: 0 0 0 0 0 0 0 VHT160: 0 0 0 0 0 0 0 PwrTxStreamDelta: 0 0 0 PwrTxNSSDelta: 0 0 0 0 start ch = 184, ch->num = 22 Band: 1 Channel: 184 188 192 196 8 12 16 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 CCK: 0 0 OFDM: 30 30 30 30 30 VHT20: 30 30 30 30 30 30 30 VHT40: 30 30 30 30 30 30 30 VHT80: 30 30 30 30 30 30 30 VHT160: 30 30 30 30 30 30 30 PwrTxStreamDelta: 0 0 0 PwrTxNSSDelta: 0 0 0 0 start ch = 96, ch->num = 22 Band: 1 Channel: 96 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173 177 181 CCK: 0 0 OFDM: 38 38 36 34 32 VHT20: 38 38 36 34 32 30 30 VHT40: 38 38 36 34 32 30 30 VHT80: 38 38 36 34 32 30 30 VHT160: 38 38 36 34 32 30 30 PwrTxStreamDelta: 0 0 0 PwrTxNSSDelta: 0 0 0 0 MtBfBackOffLoadTable: RF_LOCKDOWN Feature ON !!! MtBfBackOffLoadTable: BFBackoff Table index = 0 start ch = 1, ch->num = 14 Band: 0 Channel: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Max Power: 0 0 0 start ch = 184, ch->num = 44 Band: 1 Channel: 184 188 192 196 8 12 16 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 169 173 177 181 Max Power: 0 0 0 EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2715): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1288): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! wdev_attr_update(): wdevId0 = 98:da:c4:5f:5d:7f MtCmdSetDbdcCtrl:(ret = 0) asuka: Channel=36, wdev->channel=36 CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp<----------------- MtAsicSetChBusyStat(840): Not support for HIF_MT yet! [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 [RadarStateCheck]Set into RD_NORMAL_MODE bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8196, CmdBssInfoBmcRate.u2McTransmit = 8196 LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY mt7615_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=36, HT-CentCh=36, VHT-CentCh=42 MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(0) :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=36, VHT-CentCh=42, BBP_BW=2) [WrapDfsRadarDetectStart]: Band0Ch is 36[WrapDfsRadarDetectStart]: Band1Ch is 0MtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2573): Not support for HIF_MT yet! Main bssid = 98:da:c4:5f:5d:7f AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) MCS Set = ff ff ff ff 01 MtCmdSetMacTxRx:(ret = 0) <==== mt_wifi_init, Status=0 WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. Generate UUID for apidx(0) UUID: c0533278, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 98 da c4 5f 5d 7e wifid[wifi_exec_cmd:1548]: brctl addif br0 rai0 device rai0 entered promiscuous mode br0: port 4(rai0) entered forwarding state br0: port 4(rai0) entered forwarding state MtCmdSetDbdcCtrl:(ret = 0) ifconfig apclii0 up asuka: Channel=36, wdev->channel=36 wifid[wifi_exec_cmd:1548]: brctl addif br0 apclii0 device apclii0 entered promiscuous mode br0: port 5(apclii0) entered forwarding state br0: port 5(apclii0) entered forwarding state wifid[wifi_exec_cmd:1548]: iwpriv ra0 set RTSThreshold=2346 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set FragThreshold=2346 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set BeaconPeriod=100 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set DtimPeriod=1 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set HtGi=1 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set BasicRate=15 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set HtBssCoex=0 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set HtAmsdu=1 wifid[wifi_exec_cmd:1548]:SetEDCCACtrl: BandIdx = 0 iwpriv ra0 set EDCCACtrl=1 wifid[wifi_exec_cmd:1548]: iwpriSetPercentageCtrl: TxPowerPercentEn = 1 v ra0 set PercentageCtrl=1 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set WmmCapable=1 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set NoForwarding=0 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set NoForwardingBTNBSSID=0 wifid[wifi_exec_MtAsicSetPiggyBack(777): Not support for HIF_MT yet! cmd:1548]: iwpriMtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet! ExtEventBeaconLostHandler::FW LOG, Beacon lost (98:da:c4:5f:5d:7e), Reason 0x10 Beacon lost - AP disabled!!! WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!! v ra0 set SSID=\WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!! T\P\-\L\I\N\K\_\MtAsicSetPiggyBack(777): Not support for HIF_MT yet! E\x \_\.MtAsicSetTxPreamble(2573): Not support for HIF_MT yet! \G\H\z [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 14 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 [RadarStateCheck]Set into RD_NORMAL_MODE bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=2, HT-CentCh=4, VHT-CentCh=0 MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 BW = 1,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 4(Prim=2, HT-CentCh=4, VHT-CentCh=0, BBP_BW=1) [WrapDfsRadarDetectStart]: Band0Ch is 2[WrapDfsRadarDetectStart]: Band1Ch is 0Main bssid = 98:da:c4:5f:5d:7e wifid[wifi_exec_cmd:1548]: iwpriv rai0 set RTSThreshold=2346 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set FragThreshold=2346 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set BeaconPeriod=100 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set DtimPeriod=1 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set HtGi=1 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set BasicRate=15 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set HtBssCoex=0 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set HtAmsdu=1 wifSetEDCCACtrl: BandIdx = 0 id[wifi_exec_cmd:1548]: iwpriv rai0 set EDCCACtrl=1 wifid[wifSetPercentageCtrl: TxPowerPercentEn = 1 i_exec_cmd:1548]: iwpriv rai0 set PercentageCtrl=1 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set WmmCapable=1 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set NoForwarding=0 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set NoForwardingBTNBSSID=0 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set SSID=\T\P\-\L\I\N\K\_\E\x \_\G\H\z MtAsicSetPiggyBack(777): Not support for HIF_MT yet! asuka: WifiSysClose ExtEventBeaconLostHandler::FW LOG, Beacon lost (98:da:c4:5f:5d:7f), Reason 0x10 Beacon lost - AP disabled!!! WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!! WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!! MtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2573): Not support for HIF_MT yet! asuka: WifiSysOpen wdev_attr_update(): wdevId0 = 98:da:c4:5f:5d:7f MtCmdSetDbdcCtrl:(ret = 0) asuka: Channel=36, wdev->channel=36 [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 [RadarStateCheck]Set into RD_NORMAL_MODE bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8196, CmdBssInfoBmcRate.u2McTransmit = 8196 LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) [WrapDfsRadarDetectStart]: Band0Ch is 36[WrapDfsRadarDetectStart]: Band1Ch is 0Main bssid = 98:da:c4:5f:5d:7f wifid[mtk_init_platform:2732]: success: first time start wifi wifid[wifi_exec_cmd:1548]: iwpriv rai0 set CoCountryCode(2.4G/5G)=5/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels untryCode=DE wifid[wifi_exec_cmd:1548]: iwpriv rai0 set CountryRegionABand=1 wifid[wifi_exec_cmd:1548]: iwcfg_mode=14 priv apclii0 setcfg_mode=14 MtCmdSetDbdcCtrl:(ret = 0) wifid[wifi_exeasuka: Channel=36, wdev->channel=36 c_cmd:1548]: iwpHcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 riv rai0 set WirHcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 elessMode=14 CountryCode(2.4G/5G)=5/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels wifid[wifi_exec_cmd:1548]: iwpriv rai0 set HtBw=1 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set VhtBwMtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 =1 BW = 2,TXStream = 4, RXStream = 4, scan(0) wifid[wifi_exec_cmd:1548]: iwpriv rai0 set TxPower=100 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set AuthMode=OPEN wifid[wifi_exec_cmd:1548]: iwpriv rai0 set EncrypType=NONE wifid[wifi_exec_cmd:1548]: iwpriv rai0 set HideSSID=0 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set SSID=\T\P\-\L\I\N\K\_\E\x \_\G\H\z MtAsicSetPiggyBack(777): Not support for HIF_MT yet! asuka: WifiSysClose ExtEventBeaconLostHandler::FW LOG, Beacon lost (98:da:c4:5f:5d:7f), Reason 0x10 Beacon lost - AP disabled!!! WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!! WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!! MtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2573): Not support for HIF_MT yet! asuka: WifiSysOpen wdev_attr_update(): wdevId0 = 98:da:c4:5f:5d:7f MtCmdSetDbdcCtrl:(ret = 0) asuka: Channel=36, wdev->channel=36 [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 CountryCode(2.4G/5G)=5/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 [RadarStateCheck]Set into RD_NORMAL_MODE bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8196, CmdBssInfoBmcRate.u2McTransmit = 8196 LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) [WrapDfsRadarDetectStart]: Band0Ch is 36[WrapDfsRadarDetectStart]: Band1Ch is 0Main bssid = 98:da:c4:5f:5d:7f wifid[wifi_exec_cmd:1548]: iwpriv apclii0 set ApCliEnable=0 wifid[wifi_exec_cmd:1548]: iwpriv apclii0 set MACRepeaterEn=1 wifid[wifi_exec_cmd:1548]: iwpriv apclii0 set ApCliAuthMode=OPEN wifid[wifi_exec_cmd:1548]: iwpriv apclii0 set ApCliEncrypType=NONE wifid[wifi_exec_cmd:1548]: iwpriv apclii0 set ApCliSsid= wifid[wifi_exec_cmd:1548]: iwpriv apclii0 set ApCliEnable=1 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels CountryCode=DE wifid[wifi_exec_cmd:1548]: iwpriv ra0 set CountryRegion=1 wifid[wifi_exec_cmd:1548]: iwprivcfg_mode=9 apcli0 set ApClcfg_mode=9 iEnable=0 wifMtCmdSetDbdcCtrl:(ret = 0) id[wifi_exec_cmdasuka: Channel=2, wdev->channel=2 :1548]: iwpriv rHcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 a0 set WirelessMHcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 ode=9 CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels wifid[wifi_exec_cmd:1548]: iwpriv ra0 set HtBw=1 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set TxPower=100 wifid[wifi_exec_cmd:1548]: iwpriv ra0 set AuthMode=OPEN wifid[wifi_exec_cmd:1548]: iwpriv ra0 set EncrypType=NONE wifid[wifi_exec_cmd:1548]: iwpriv ra0 set HideSSID=0 wifid[wifi_exec_cmd:1548MtAsicSetPiggyBack(777): Not support for HIF_MT yet! ]: iwpriv ra0 seMtAsicSetRalinkBurstMode(2594): Not support for HIF_MT yet! ExtEventBeaconLostHandler::FW LOG, Beacon lost (98:da:c4:5f:5d:7e), Reason 0x10 Beacon lost - AP disabled!!! WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!! WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!! t SSID=\T\P\-\L\MtAsicSetPiggyBack(777): Not support for HIF_MT yet! I\N\K\_\E\x \MtAsicSetTxPreamble(2573): Not support for HIF_MT yet! \_\.\G\H\z [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=2 CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 [RadarStateCheck]Set into RD_NORMAL_MODE bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=2, HT-CentCh=4, VHT-CentCh=0 MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 BW = 1,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 4(Prim=2, HT-CentCh=4, VHT-CentCh=0, BBP_BW=1) [WrapDfsRadarDetectStart]: Band0Ch is 2[WrapDfsRadarDetectStart]: Band1Ch is 0Main bssid = 98:da:c4:5f:5d:7e wifid[wifi_exec_cmd:1548]: iwpriv apcli0 set ApCliEnable=0 wifid[wifi_exec_cmd:1548]: iwpriv apcli0 set MACRepeaterEn=1 wifid[wifi_exec_cmd:1548]: iwpriv apcli0 set ApCliAuthMode=OPEN wifid[wifi_exec_cmd:1548]: iwpriv apcli0 set ApCliEncrypType=NONE wifid[wifi_exec_cmd:1548]: iwpriv apcli0 set ApCliSsid= wifid[wifi_exec_cmd:1548]: iwpriv apcli0 set ApCliEnable=1 wifid[mtk_init_platform:2735]: success: start wifi wifid[mtk_init_platform:2738]: success: register msgcenter wifid[wifi_exec_cmd:1548]: echo 0 >/pro1,count is 33 c/range_extenderr_config/range_exatender_link_stat0e wifid[wifi_:exec_cmd:1548]: recho 1 > /proc/raange_extender_coinfig/range_exten0der_psr_alias_ru:le wifid[wifie_exec_cmd:1548]:t echo 0 > /proc/hrange_extender_c2onfig/range_exte:nder_eth_to_2g_ebnable wifid[wrifi_exec_cmd:15408]: echo 'ra0:ra:i0:eth2:br0:apclai0:apclii0' > /pproc/range_extendcer_config/range_lextender_br_dev_iname 0:apclii0 wifid[wifi_exec_cmd:1548]: echo 1 >/proc/range_extender_config/rrange_extender_braidge_deliver_ena0ble wifid[wif:i_exec_cmd:1548]r: echo 'ra0:rai0a:eth2' > /proc/dihcp_hook/dhcp_ho0ok_dev_name :eth2 wifid[mtk_init_platform:2741]: success: set proc info wifid[wifi_exec_cmd:1548]: wpsd wifid[mtk_init_platform:2744]: success: start wpsd wifid[wifi_exec_cmd:1548]: iwpriv ra0 set AccessPolicy=0 wifid[wifi_exec_cmd:1548]: iwpriv rai0 set AccessPolicy=0 wifid[wifi_exec_cmd:1548]: echo 1 > /tmp/wifi_acl_reload_all wifid[mtk_init_platform:2747]: success: reload acl wifid[mtk_init_platform:2750]: success: setup DUT pin wifid[wifi_exec_cmd:1548]: wifi chaninfo DE wifid[wifi_exec_cmd:1548]: smp.sh wifi wifid[wifi_exec_cmd:1548]: echo 1 > /tmp/wifi_mod_exist wifid[wifi_exec_cmd:1548]: mii_mgr -s -p 0 -r 0 -v 3300 wifid[wifi_exec_cmd:1548]: echo 1 > /proc/sys/vm/drop_caches wifid detected starting pid 457, tty '': '/sbin/getty ttyS1 57600' httpMudCreate: MUD 0x4ac650 was created httpServerCreate: try to add port 80 RE650 login:
OpenWrt bootlog
=================================================================== MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11000000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL4 FB_DL: 0x9, 1/0 = 609/415 25000000 PLL2 FB_DL: 0xe, 1/0 = 763/261 39000000 PLL3 FB_DL: 0x15, 1/0 = 557/467 55000000 do DDR setting..[01F40000] Apply DDR3 Setting...(use default AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 opt_dle value:10 DRAMC_R0DELDLY[018]=00001E1D ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 7 7 7 9 6 7 6 5 5 6 10 | 7 9 7 11 8 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =29 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (2~55)28 8 (1~57)29 1 (2~55)28 9 (1~56)28 2 (1~56)28 10 (1~59)30 3 (1~58)29 11 (1~57)29 4 (1~57)29 12 (1~60)30 5 (2~57)29 13 (1~57)29 6 (1~55)28 14 (1~59)30 7 (1~58)29 15 (1~57)29 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 8 8 8 9 6 7 7 5 6 8 10 | 7 10 7 12 8 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff2000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 DQS loop = 14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=500000000 HZ BUS=166666666 HZ =================================================================== U-Boot 1.1.3 (Jul 19 2018 - 10:08:42) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb8000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** flash manufacture id: ef, device id 40 18 find flash: W25Q128BV *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Jul 19 2018 Time:10:08:42 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 gpioMode Reg: 0x4852c Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bfc20000 ... text base: 80001000 entry point: 80001000 Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 128 Starting kernel ... [ 0.000000] Linux version 5.4.70 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14664-156b72b9aa)) #0 SMP Sat Oct 10 19:15:38 2020 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is TP-Link RE650 v1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00010000 [ 0.000000] Readback ErrCtl register=00010000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 120580K/131072K available (5939K kernel code, 209K rwdata, 1276K rodata, 1268K init, 238K bss, 10492K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.015493] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.055838] pid_max: default: 32768 minimum: 301 [ 0.065186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.079591] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.097701] rcu: Hierarchical SRCU implementation. [ 0.107809] smp: Bringing up secondary CPUs ... [ 0.118467] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.118477] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.118489] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.118591] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.144999] Synchronize counters for CPU 1: done. [ 0.228364] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.228372] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.228380] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.228437] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.243533] Synchronize counters for CPU 2: done. [ 0.304736] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.304744] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.304752] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.304810] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.331140] Synchronize counters for CPU 3: done. [ 0.390748] smp: Brought up 1 node, 4 CPUs [ 0.403191] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.422504] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.436424] pinctrl core: initialized pinctrl subsystem [ 0.448375] NET: Registered protocol family 16 [ 0.485640] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.506730] clocksource: Switched to clocksource GIC [ 0.518329] NET: Registered protocol family 2 [ 0.527825] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.544459] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.559586] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.573572] TCP: Hash tables configured (established 1024 bind 1024) [ 0.586326] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.599235] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.613321] NET: Registered protocol family 1 [ 0.621890] PCI: CLS 0 bytes, default 32 [ 0.718694] 4 CPUs re-calibrate udelay(lpj = 1163264) [ 0.729890] random: fast init done [ 0.730343] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.761340] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.772852] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.793990] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.810552] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.821875] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.833157] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.844910] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.860744] printk: console [ttyS0] disabled [ 0.869216] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.887133] printk: console [ttyS0] enabled [ 0.887133] printk: console [ttyS0] enabled [ 0.903679] printk: bootconsole [early0] disabled [ 0.903679] printk: bootconsole [early0] disabled [ 0.925312] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 0.945873] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.955490] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.968147] Creating 4 MTD partitions on "spi0.0": [ 0.977698] 0x000000000000-0x000000020000 : "u-boot" [ 0.988894] 0x000000020000-0x000000e00000 : "firmware" [ 1.000782] 2 tplink-fw partitions found on MTD device firmware [ 1.012611] Creating 2 MTD partitions on "firmware": [ 1.022509] 0x000000000000-0x00000025da69 : "kernel" [ 1.033643] 0x00000025da69-0x000000de0000 : "rootfs" [ 1.044868] mtd: device 3 (rootfs) set to be root filesystem [ 1.056268] 1 squashfs-split partitions found on MTD device rootfs [ 1.068641] 0x000000570000-0x000000de0000 : "rootfs_data" [ 1.080813] 0x000000e00000-0x000000e50000 : "config" [ 1.092138] 0x000000ff0000-0x000001000000 : "radio" [ 1.104251] libphy: Fixed MDIO Bus: probed [ 1.137106] libphy: mdio: probed [ 1.143770] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.157095] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 1.175850] mt7621-pci 1e140000.pcie: Parsing DT failed [ 1.188832] NET: Registered protocol family 10 [ 1.199422] Segment Routing with IPv6 [ 1.206850] NET: Registered protocol family 17 [ 1.215779] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.241836] 8021q: 802.1Q VLAN Support v1.8 [ 1.252075] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.271653] libphy: dsa slave smi: probed [ 1.280051] mt7530 mdio-bus:1f lan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 1.298569] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 1.316204] DSA: tree 0 setup [ 1.322433] rt2880-pinmux pinctrl: pcie is already enabled [ 1.333392] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 1.348451] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 1.363397] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.478018] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.489140] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.600054] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.613930] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.623654] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.633380] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.652094] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.664773] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.678475] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.692184] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.703173] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.715186] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.727685] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff] [ 1.740247] pci 0000:00:00.0: supports D1 [ 1.748240] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.760048] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.772063] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.784569] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff] [ 1.797121] pci 0000:00:01.0: supports D1 [ 1.805114] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.818022] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 1.830061] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 1.843769] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.872589] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.883025] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.895173] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.908704] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.923106] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.936500] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280 [ 1.948530] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 1.962221] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.991101] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 2.001522] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 2.013670] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 2.027205] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 2.041609] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.054846] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 2.068031] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.081907] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 2.095091] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.108967] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 2.122504] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 2.136902] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 2.150431] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 2.164828] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 2.178362] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 2.191898] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 2.205427] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 2.218968] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 2.233544] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.243446] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 2.256979] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.270506] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 2.284909] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] [ 2.299492] pci 0000:00:01.0: PCI bridge to [bus 02] [ 2.309384] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 2.322915] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 2.336441] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 2.351392] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 2.351751] hctosys: unable to open rtc device (rtc0) [ 2.379512] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.397794] Freeing unused kernel memory: 1268K [ 2.406844] This architecture does not have kernel memory protection. [ 2.419667] Run /sbin/init as init process [ 2.989799] init: Console is alive [ 2.996834] init: - watchdog - [ 3.638235] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.738822] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.759058] init: - preinit - [ 4.411581] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 4.427669] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 4.444542] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 4.592276] random: jshn: uninitialized urandom read (4 bytes read) [ 4.660243] random: jshn: uninitialized urandom read (4 bytes read) [ 4.706398] random: jshn: uninitialized urandom read (4 bytes read) [ 4.949843] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode [ 4.963280] 8021q: adding VLAN 0 to HW filter on device lan Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.177972] jffs2: notice: (570) jffs2_build_xattr_subsystem: complete building xattr subsystem, 62 of xdatum (15 unchecked, 46 orphan) and 69 of xref (44 dead, 2 orphan) found. [ 9.211393] mount_root: switching to jffs2 overlay [ 9.236034] overlayfs: upper fs does not support tmpfile. [ 9.252418] urandom-seed: Seeding with /etc/urandom.seed [ 9.409844] procd: - early - [ 9.415733] procd: - watchdog - [ 10.002872] procd: - watchdog - [ 10.009496] procd: - ubus - [ 10.068951] procd: - init - Please press Enter to activate this console. [ 10.483228] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.508458] Loading modules backported from Linux version v5.8-0-gbcf876870b95 [ 10.522921] Backport generated by backports.git v5.8-1-0-g79400d9e [ 10.551784] xt_time: kernel timezone is -0000 [ 10.616200] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 10.627015] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 10.638299] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 10.667863] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24 [ 10.678782] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 10.688726] urngd: v1.0.2 started. [ 10.690107] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 10.716865] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 10.716865] [ 10.758049] PPP generic driver version 2.4.2 [ 10.768172] NET: Registered protocol family 24 [ 10.769972] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 10.769972] [ 10.811537] kmodloader: done loading kernel modules from /etc/modules.d/* [ 10.910674] random: crng init done [ 10.917546] random: 7 urandom warning(s) missed due to ratelimiting [ 11.044585] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 11.044617] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 11.131139] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 11.154829] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 15.401419] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 15.419435] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 15.435890] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 15.437588] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode [ 15.466293] 8021q: adding VLAN 0 to HW filter on device lan BusyBox v1.31.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r14664-156b72b9aa ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@ap-a:/#
Notes
Space for additional notes, links to forum threads or other resources.
- ...