TP-Link Archer VR2600v v1
Wireless-AC router based on QCA IPQ8064 with 16MB flash and 512MB RAM. Also sporting xDSL support with BCM63168 SOC and a DSP for VoIP POTS interface and DECT.
Supported Versions
Hardware Highlights
Installation
- Establish serial connection to device (see below)
- Interrupt boot process of bootloader by pressing any key
- Setup IP addresses of board and TFTP server (replace IPs with your own)
(IPQ) # setenv ipaddr 10.42.21.50 (IPQ) # setenv serverip 10.42.21.200
- Disable autoboot and probe for the serial flash
(IPQ) # setenv autoboot false (IPQ) # sf probe
- Transfer the image from TFTP to the RAM. Replace filename to match your image. Note the Bytes transferred length (0x4c0aa bytes in this example)
(IPQ) # tftpboot 0x44000000 sysupgrade.bin Using eth0 device TFTP from server 10.42.21.200; our IP address is 10.42.21.50 Filename 'sysupgrade.bin'. Load address: 0x44000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### done Bytes transferred = 4980906 (4c00aa hex)
- Erase the flash area with the kernel image and rootfs. Write the new image from RAM to flash. Change the size to match the Bytes transferred length from previous step. (0x4c0aa bytes in this example).
(IPQ) # sf erase 0x320000 0xc60000 (IPQ) # sf write 0x44000000 0x320000 0x4c00aa
These commands need some time executing.
- Reboot to OpenWRT. The next update can be done by sysupgrade
Flash Layout
0x000000000000-0x000000020000 | “SBL1” |
0x000000020000-0x000000040000 | “MIBIB” |
0x000000040000-0x000000080000 | “SBL2” |
0x000000080000-0x000000100000 | “SBL3” |
0x000000100000-0x000000110000 | “DDRCONFIG” |
0x000000110000-0x000000120000 | “SSD” |
0x000000120000-0x0000001a0000 | “TZ” |
0x0000001a0000-0x000000220000 | “RPM” |
0x000000220000-0x0000002a0000 | “APPSBL” |
0x0000002a0000-0x0000002e0000 | “APPSBLENV” |
0x0000002e0000-0x000000320000 | “OLDART” |
0x000000320000-0x000000520000 | “kernel” |
0x000000520000-0x000000f80000 | “rootfs” |
0x000000faf100-0x00000faf0200 | “default-mac” |
0x000000fc0000-0x000001000000 | “ART” |
OEM installation using the TFTP method
Specific values needed for tftp
Press and hold reset button and turn on device:
Bootloader tftp client IPv4 address | 192.168.1.1 |
---|---|
Bootloader MAC address (special) | FILL-IN |
Firmware tftp image | Latest OpenWrt release (NOTE: Change filename to “ArcherC2600_1.0_tp_recovery.bin”) |
TFTP transfer window | FILL-IN seconds |
TFTP window start | approximately 10 seconds after power on |
TFTP server IP address | 192.168.1.100 |
Note: make sure the router and the PC are connected directly, not through a switch (more info)
Upgrading OpenWrt
LuCI Web Upgrade Process
- Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
- Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are command line method for upgrading:
sysupgrade
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
Debricking
If you are experimenting with C2600 and you flash the wrong firmware and the device doesn't boot, you can restore the factory firmware:
- Set PC to fixed ip address 192.168.0.66
- Download factory firmware from TP-Link and rename it to ArcherC2600_1.0_tp_recovery.bin
- Start a tftp server with the file ArcherC2600_1.0_tp_recovery.bin in its root directory
- Turn off the router
- Press and hold Reset button
- Turn on router with the reset button pressed and wait ~15 seconds
- Release the reset button and after a short time the firmware should be transferred from the tftp server
- Wait ~5 minute to complete recovery.
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Network interfaces
The default network configuration is:
Interface Name | Description | Default configuration |
---|---|---|
br-lan | LAN & WiFi | 192.168.1.1/24 |
vlan1 (eth0) | LAN ports (1 to 4) | None |
vlan2 (eth1) | WAN port | DHCP |
wlan0 | WiFi 5GHz | Disabled |
wlan1 | WiFi 2,4GHz | Disabled |
Switch Ports (for VLANs)
Numbers 4-1 are Ports 1-4 as labeled on the unit, number 5 is the Internet (WAN) on the unit, 0 and 6 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 4 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
Port | Switch port |
---|---|
Internet (WAN) | 5 |
LAN 1 | 4 |
LAN 2 | 3 |
LAN 3 | 2 |
LAN 4 | 1 |
GMII | 0 (marked as CPU) Switch0 CPU Port eth0 |
6 Switch0 CPU Port eth1 |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
The TP-Link Archer VRR2600v has the following buttons:
BUTTON | Event |
---|---|
Reset | reboot/reset |
WPS | - |
WiFi On/Off | rfkill |
DECT On/Off | - |
LED On/Off | - |
Hardware
Info
Photos
The power connector is a regular 2.1 x 5.5mm barrel socket. Positive polarity on centre pin. The router is rated to 3.3 Amps because it has two USB3 sockets, each socket rated to 0.9 Amps.
Opening the case
See https://forum.openwrt.org/t/tp-link-archer-vr2600-installation/48081/7
Note: This will void your warranty!
- Pull off the 4 rubber feet.
- Remove the 4 screws.
- Place the router on table with top cover facing upwards.
- Starting from the rear edge above the LAN sockets. Insert a metal spudger horizontally pushing past the ventilation slots. Lift/lever the free end of the spudger upwards. There are 4 plastic clips to unlatch.
- Repeat for the left and right sides of the cover.
- Warning: Take care when pulling the cover away from the case to separate the clips on the front edge of the cover. There is a short flat cable connected to the underside of the lid. Lift the small latch to enable the flat cable to slide off the connector.
Main PCB:
Insert photo of PCB
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the serial port of this specific device:
- Open Device
- Find space for four pin header name JP2 (next to WAN port)
- Solder four pin header to JP2
- Use MAX232 or UART to USB device for 3.3V
- Pin1: TXD, Pin2: RXD, Pin3: GND, Pin4: 3.3V
Image below is from VR2600. JP2 pinout is identical to VR2600v
Serial connection parameters for TP-Link Archer VR2600v v1 | 115200, 8N1 |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootloader mods
Hardware mods
None so far.
Bootlogs
OEM bootlog
U-Boot 2012.07-svn13437 [Standard IPQ806X.LN,r40858] (Feb 04 2016 - 14:16:32) smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: ipq_nand: unknown NAND device manufacturer: 0 device: 0 ipq_nand: failed to identify device SF: we have a match, call probe SF: Detected W25Q128 with page size 64 KiB, total 16 MiB ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000 16 MiB MMC: *** Warning - bad CRC, using default environment PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial Net: No ART partition found MAC1 addr:0:3:7f:ba:db:1 S17c athrs17_init_switch done. WJL: athrs17_reg_init() reg-0x30=0x80000700.1. WJL: athrs17_reg_init() reg-0x30=0x80000401.2. WJL: athrs17_reg_init: PAD config after SOFT_RESET. WJL: athrs17_reg_init: 0x0000007c=0x00001080.1. WJL: athrs17_reg_init: 0x00000094=0x00001080.2. athrs17_reg_init: complete S17c init done (WJL-07-10-1829, uboot task - internal loopback) MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:aa:bb:cc:dd:ee , eth1 Hit any key to stop autoboot: 1 0 MMC Device 0 not found MMC Device 0 not found Loading from nand1, offset 0x320200 Image Name: Linux-3.4.103 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1884744 Bytes = 1.8 MiB Load Address: 41508000 Entry Point: 41508000 Automatic boot of image at addr 0x44000000 ... Image Name: Linux-3.4.103 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1884744 Bytes = 1.8 MiB Load Address: 41508000 Entry Point: 41508000 Verifying Checksum ... OK Loading Kernel Image ... OK OK device nand1 <nand1>, # parts = 1 #: name size offset mask_flags 0: ART 0x00040000 0x00fc0000 0 active partition: nand1,0 - (ART) 0x00040000 @ 0x00fc0000 defaults: mtdids : none mtdparts: none Setting up atags for msm partition: ART Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.103 (root@localhost.localdomain) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #329 SMP PREEMPT Thu Feb 4 14:45:57 HKT 2016 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: Qualcomm Atheros AP148 reference board [ 0.000000] Partition (from atag) ART -- Offset:fc Size:4 [ 0.000000] msm_reserve_memory: 0x44000000, 0x600000 [ 0.000000] msm_reserve_memory: 0x44600000, 0x200000 [ 0.000000] memory pool 3 (start 5fc00000 size 400000) initialized [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] smem_find(137, 80): wrong size 72 [ 0.000000] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536 [ 0.000000] accessory_chip=0 hw_plat_subtype=0 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0c7d000 s10816 r8192 d13760 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121642 [ 0.000000] Kernel command line: console=ttyHSL1,115200n8 root=mtd:rootfs rootfstype=squashfs [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 43MB 436MB = 479MB total [ 0.000000] Memory: 477212k/489500k available, 13284k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdf000000 - 0xff000000 ( 512 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdeb00000 ( 491 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc051c000 (5200 kB) [ 0.000000] .init : 0xc0600000 - 0xc0702a40 (1035 kB) [ 0.000000] .data : 0xc0704000 - 0xc07a5e48 ( 648 kB) [ 0.000000] .bss : 0xc07a5e6c - 0xc08790d0 ( 845 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:1689 [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms [ 0.000000] Console: colour dummy device 80x30 [ 0.150452] Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62799) [ 0.150484] pid_max: default: 32768 minimum: 301 [ 0.150921] Mount-cache hash table entries: 512 [ 0.152389] CPU: Testing write buffer coherency: ok [ 0.152608] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152639] hw perfevents: enabled with ARMv7 Krait PMU driver, 5 counters available [ 0.152733] Setting up static identity map for 0x418a61f8 - 0x418a6280 [ 0.155014] CPU1: Booted secondary processor [ 0.155107] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.155201] Brought up 2 CPUs [ 0.155201] SMP: Total of 2 processors activated (25.11 BogoMIPS). [ 0.171727] dummy: [ 0.172414] NET: Registered protocol family 16 [ 0.173195] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver [ 0.175507] meminfo_init: smem ram ptable found: ver: 0 len: 5 [ 0.175538] Found 1 memory banks grouped into 8 memory regions [ 0.175820] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio [ 0.176632] smem_find(137, 80): wrong size 72 [ 0.176663] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536 [ 0.176663] accessory_chip=0 hw_plat_subtype=0 [ 0.176694] msm_rpm_init: RPM firmware 3.0.16777342 [ 0.184442] clk_tbl_nss - loaded [ 0.211558] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.211558] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.211965] msm_dmov_memcpy_init: Success [ 0.219587] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20 [ 0.219618] sps:BAM 0x12244000 is registered. [ 0.219868] sps:sps is ready. [ 0.260918] msm_pcie_setup: link initialized [ 0.261324] PCI host bridge to bus 0000:00 [ 0.261324] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff] [ 0.261855] PCI: bus0: Fast back to back transfers disabled [ 0.261855] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.262699] PCI: bus1: Fast back to back transfers disabled [ 0.301030] msm_pcie_setup: link initialized [ 0.301405] PCI host bridge to bus 0000:02 [ 0.301405] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff] [ 0.301874] PCI: bus2: Fast back to back transfers disabled [ 0.301905] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.302624] PCI: bus3: Fast back to back transfers disabled [ 0.421368] msm_pcie_setup: link initialization failed [ 0.421587] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.421618] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.421649] pci 0000:02:00.0: PCI bridge to [bus 03-03] [ 0.421680] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.421743] PCI: enabling device 0000:02:00.0 (0140 -> 0143) [ 0.421805] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.421805] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.421868] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.421899] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.421930] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 0.445454] bio: create slab <bio-0> at 0 [ 0.447422] SCSI subsystem initialized [ 0.449265] spi_qsd spi_qsd.5: master is unqueued, this is deprecated [ 0.451733] spi_qsd spi_qsd.6: master is unqueued, this is deprecated [ 0.455607] Switching to clocksource gp_timer [ 0.477413] NET: Registered protocol family 2 [ 0.487129] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.487753] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.487941] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 0.488128] TCP: Hash tables configured (established 16384 bind 16384) [ 0.488159] TCP: reno registered [ 0.488159] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.488191] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.488628] NET: Registered protocol family 1 [ 0.489971] Detected 5 counters on the L2CC PMU. [ 0.491002] smd: register irq failed on wcnss_a11 [ 0.491034] smd: deregistering IRQs [ 0.491065] SMD: smd_core_platform_init() failed [ 0.491815] Partition(from smem) SBL1 -- Offset:0 Size:20000 [ 0.491846] Partition(from smem) MIBIB -- Offset:20000 Size:20000 [ 0.491846] Partition(from smem) SBL2 -- Offset:40000 Size:40000 [ 0.491877] Partition(from smem) SBL3 -- Offset:80000 Size:80000 [ 0.491877] Partition(from smem) DDRCONFIG -- Offset:100000 Size:10000 [ 0.491908] Partition(from smem) SSD -- Offset:110000 Size:10000 [ 0.491908] Partition(from smem) TZ -- Offset:120000 Size:80000 [ 0.491940] Partition(from smem) RPM -- Offset:1a0000 Size:80000 [ 0.491971] Partition(from smem) APPSBL -- Offset:220000 Size:80000 [ 0.491971] Partition(from smem) APPSBLENV -- Offset:2a0000 Size:40000 [ 0.492002] Partition(from smem) kernel -- Offset:320000 Size:200000 [ 0.492033] Partition(from smem) rootfs -- Offset:520000 Size:a60000 [ 0.492033] get_bootconfig_partition: magic not found [ 0.507154] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0 [ 0.507154] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 1 [ 0.513776] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported [ 0.513808] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported [ 0.515338] msm_rpm_log_probe: OK [ 0.533801] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.534864] fuse init (API version 7.18) [ 0.536144] msgmni has been set to 932 [ 0.538206] io scheduler noop registered [ 0.538206] io scheduler deadline registered (default) [ 0.540018] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.543392] msm_serial_hs.0: ttyHS0 at MMIO 0x12490000 (irq = 227) is a MSM HS UART [ 0.544048] msm_serial_hs module loaded [ 0.544236] msm_serial_hsl: detected port #1 [ 0.544361] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM [ 0.544798] msm_serial_hsl: console setup on port #1 [ 1.315432] console [ttyHSL1] enabled [ 1.319587] msm_serial_hsl: driver initialized [ 1.341049] brd: module loaded [ 1.350984] loop: module loaded [ 1.357731] ahci ahci.0: forcing PORTS_IMPL to 0x1 [ 1.361543] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.369447] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 1.378600] scsi0 : ahci_platform [ 1.381568] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241 [ 1.391565] Register flash device: flash0, major=200 [ 1.397656] m25p80 spi5.0: found w25q128, expected s25fl512s [ 1.402280] m25p80 spi5.0: w25q128 (16384 Kbytes) [ 1.407653] Creating 13 MTD partitions on "m25p80": [ 1.411840] 0x000000fc0000-0x000001000000 : "ART" [ 1.418650] 0x000000000000-0x000000020000 : "SBL1" [ 1.424148] 0x000000020000-0x000000040000 : "MIBIB" [ 1.429803] 0x000000040000-0x000000080000 : "SBL2" [ 1.435270] 0x000000080000-0x000000100000 : "SBL3" [ 1.440830] 0x000000100000-0x000000110000 : "DDRCONFIG" [ 1.446797] 0x000000110000-0x000000120000 : "SSD" [ 1.452264] 0x000000120000-0x0000001a0000 : "TZ" [ 1.458044] 0x0000001a0000-0x000000220000 : "RPM" [ 1.464261] 0x000000220000-0x0000002a0000 : "APPSBL" [ 1.470790] 0x0000002a0000-0x0000002e0000 : "APPSBLENV" [ 1.477600] 0x000000320000-0x000000520000 : "kernel" [ 1.484067] 0x000000520000-0x000000f80000 : "rootfs" [ 1.490627] mtd: partition "rootfs" set to be root filesystem [ 1.495938] mtd: partition "rootfs_data" created automatically, ofs=EA0000, len=E0000 [ 1.503248] 0x000000ea0000-0x000000f80000 : "rootfs_data" [ 1.511340] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 1.562699] GPIO Bitbanged MDIO: probed [ 1.566198] PPP generic driver version 2.4.2 [ 1.570384] NET: Registered protocol family 24 [ 1.575476] ipq-dwc3 ipq-dwc3.0: unable to read platform data num of dbm eps [ 1.684879] ipq-dwc3 ipq-dwc3.1: unable to read platform data num of dbm eps [ 1.735707] ata1: SATA link down (SStatus 0 SControl 300) [ 1.804686] cpuidle: using governor ladder [ 1.807841] cpuidle: using governor menu [ 1.816963] Mirror/redirect action on [ 1.819587] u32 classifier [ 1.822274] Actions configured [ 1.825741] Netfilter messages via NETLINK v0.30. [ 1.830396] nf_conntrack version 0.5.0 (7456 buckets, 51200 max) [ 1.837675] ctnetlink v0.93: registering with nfnetlink. [ 1.842767] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.848109] TCP: cubic registered [ 1.852389] NET: Registered protocol family 10 [ 1.858606] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.863323] IPv6 over IPv4 tunneling driver [ 1.870977] NET: Registered protocol family 17 [ 1.874476] NET: Registered protocol family 15 [ 1.879162] Bridge firewalling registered [ 1.882849] Ebtables v2.0 registered [ 1.886504] 8021q: 802.1Q VLAN Support v1.8 [ 1.890690] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 1.898562] Registering SWP/SWPB emulation handler [ 1.903030] clock_late_init: Removing enables held for handed-off clocks [ 1.918338] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff [ 1.922992] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff [ 1.928709] ipq_nss_get_mac_addr: MAC[3]: ff:ff:ff:ff:ff:ff [ 1.934176] no pmic restart interrupt specified [ 1.940143] msm_cache_dump_probe: could not register L2 buffer ret = -22. [ 1.947766] input: gpio-keys as /devices/platform/gpio-keys/input/\FF[ 1.963636] VFS: Mounted root (squashfs filesystem) readonly on device 31:12. [ 1.970384] Freeing init memory: 1032K starting pid 826, tty '': '/etc/init.d/rcS' [ 3.400968] ssdk_plat_init start [ 3.508497] Register QCA PHY driver [ 3.746610] qca-ssdk module init succeeded! [ 3.911496] ********************************************************** [ 3.916838] * Driver :NSS GMAC Driver for RTL v(3.72a) [ 3.922180] * Version :1.0 [ 3.925054] * Copyright :Copyright (c) 2013-2014 The Linux Foundation. All rights reserved. [ 3.933395] **********************************************************mdio bus 'gpio-0' OK. [ 6.475070] Initialized NSS GMAC2 interface eth0: (base = 0x37400000, irq = 258, PhyId = 0, PollLink = 0) [ 6.483723] mdio bus 'gpio-0' OK. [ 6.486879] GMAC1(de1d64c0) Invalid MAC@ - using 1e:1f:20:21:22:23PHY gpio-0:04 attach OK [ 6.509497] nss_gmac_probe: Program RGMII Tx delay..... [ 6.515276] eth%d MII_PHYSID1 - 0x004d [ 6.518213] eth%d MII_PHYSID2 - 0xd036 [ 6.524336] Initialized NSS GMAC1 interface eth1: (base = 0x37200000, irq = 255, PhyId = 4, PollLink = 1) [ 6.534645] mdio bus 'gpio-0' OK. [ 6.536925] GMAC0(de1d7cc0) Invalid MAC@ - using 8e:8f:90:91:92:93Initialized NSS GMAC0 interface eth2: (base = 0x37000000, irq = 252, PhyId = 32, PollLink = 0) [ 6.975413] nss_driver - fw of size 354304 bytes copied to load addr: 40000000, nss_id : 0 [ 7.005185] nss_driver - Turbo Support 1 [ 7.013120] bf0f72ed: NSS Shaping is enabled, handler id: 0 [ 7.053639] nss_driver - fw of size 5392 bytes copied to load addr: 40800000, nss_id : 1 [ 7.074601] Error - Duplicate Interface CB Registered for interface 75 [ 7.080131] Error - Duplicate Interface CB Registered for interface 78 [ 7.102155] Enabling NSS RPS [ 7.128553] nss_macsec init success [ 7.281880] button_hotplug: module license 'unspecified' taints kernel. [ 7.287503] Disabling lock debugging due to kernel taint [ 7.295251] Button Hotplug driver version 0.4.1 [ 7.565791] ECM init [ 7.587691] ECM init complete [ 7.829709] usbcore: registered new interface driver usbfs [ 7.835676] usbcore: registered new interface driver hub [ 7.842549] usbcore: registered new device driver usb [ 7.974945] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 7.979037] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 [ 7.986285] xhci-hcd xhci-hcd.0: irq 142, io mem 0x11000000 [ 7.995657] hub 1-0:1.0: USB hub found [ 7.998375] hub 1-0:1.0: 1 port detected [ 8.002436] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 8.007372] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 [ 8.015182] hub 2-0:1.0: USB hub found [ 8.018275] hub 2-0:1.0: 1 port detected [ 8.022399] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 8.027241] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3 [ 8.034489] xhci-hcd xhci-hcd.1: irq 237, io mem 0x10000000 [ 8.040674] hub 3-0:1.0: USB hub found [ 8.043705] hub 3-0:1.0: 1 port detected [ 8.049671] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 8.053701] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4 [ 8.061543] hub 4-0:1.0: USB hub found [ 8.064636] hub 4-0:1.0: 1 port detected [ 8.075538] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.081162] msm_hsusb_host msm_hsusb_host: unable to find transceiver [ 8.095313] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.203623] Initializing USB Mass Storage driver... [ 8.209528] usbcore: registered new interface driver usb-storage [ 8.214495] USB Mass Storage support registered. [ 8.489315] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. [ 8.635988] Tuxera FAT 12/16/32 driver version 3014.9.10 [Flags: R/W MODULE]. [ 8.672352] Tuxera HFS+ driver 3014.7.28 [ 8.800624] Tuxera exFAT driver version 3014.9.10 [Flags: R/W MODULE]. [ 8.926398] dns_init [ 8.927553] domain_name:tplinkmodem.net /dev/mem opened. Memory mapped at address 0x401c5000. Value at address 0x801020 (0x401c5020): 0x1C0 Written 0x1C0; readback 0x1C0 /dev/mem opened. Memory mapped at address 0x40261000. Value at address 0x801420 (0x40261420): 0x3C3 Written 0x3C3; readback 0x3C3 Please press Enter to activate this console. [ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml /bin/sh: can't create /proc/tplink/eth_vlan: nonexistent directory ddns_ud> start enable = 0, server: , auth: , request SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. ioctl: No such device [ 14.024773] device eth0.2 entered promiscuous mode [ 14.028647] device eth0 entered promiscuous mode [ 14.033239] br0: port 1(eth0.2) entered forwarding state [ 14.038456] br0: port 1(eth0.2) entered forwarding state [ 14.051421] device eth0.3 entered promiscuous mode [ 14.055263] br0: port 2(eth0.3) entered forwarding state [ 14.060512] br0: port 2(eth0.3) entered forwarding state [ 14.073133] device eth0.4 entered promiscuous mode [ 14.077007] br0: port 3(eth0.4) entered forwarding state [ 14.082193] br0: port 3(eth0.4) entered forwarding state [ 14.094689] device eth0.5 entered promiscuous mode [ 14.098656] br0: port 4(eth0.5) entered forwarding state [ 14.103748] br0: port 4(eth0.5) entered forwarding state *********cal_data_2g******* 202f612a0000000016000000 *********cal_data_end******* *********cal_data_5g******* 202ffd2d0000000000161616 *********cal_data_end******* [ 14.665635] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) [ 14.697375] ath_spectral: Version 2.0.0 [ 14.697407] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 14.707997] SPECTRAL module built on Nov 5 2015 15:58:04 [ 14.718775] ath_tx99: Version 2.0 [ 14.718775] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved [ 14.732989] ath_dfs: Version 2.0.0 [ 14.732989] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 14.747828] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 14.999500] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 16.235895] ath_pci: (Atheros/multi-bss) [ 16.238894] ath_pci_probe [ 16.241487] PCI device id is 0040 :0040 [ 16.245298] PCI: enabling device 0000:01:00.0 (0140 -> 0142) [ 16.251202] ath_pci 0000:01:00.0: ath DEBUG: sc=0xdd913a00 [ 16.256419] [ 16.256419] ol_ath_pci_configure : num_desired MSI set to 0 [ 16.263542] [ 16.263542] Using PCI Legacy Interrupt [ 16.268853] chip_id 9 chip_revision 1 [ 16.273133] [ 16.273133] address 4008f8 data db6c7c30 [ 16.279162] [ 16.279162] address 401e90 data db6c7c34 [ 16.285754] [ 16.285754] address 401e94 data db6c7c38 [ 16.292377] [ 16.292377] address 401eb0 data db6c7c3c [ 16.299000] [ 16.299000] address 400900 data db6c7c3c [ 16.305654] [ 16.305654] CLOCK PLL skipped [ 16.309215] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff [ 16.317057] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL [ 16.324336] HIF_PCIDeviceProbed: ar900b_20_targ_clk is not provided, skipping pre-configuring PLL [ 16.336394] [ 16.336394] address 4008cc data db6c7c3c [ 16.343017] __ol_ath_attach: ath_attach TODO [ 16.346266] __ol_ath_attach 1755 host_enable 0 nss_nwifi_offload 0 [ 16.352421] __ol_ath_attach: dev name wifi0 [ 16.356607] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 16.365948] OL_ACBKMinfree : 0 [ 16.369072] OL_ACBEMinfree : 0 [ 16.372196] OL_ACVIMinfree : 0 [ 16.375320] OL_ACVOMinfree : 0 [ 16.378475] ol_ath_attach() BMI inited. [ 16.382411] ol_ath_attach() BMI Get Target Info. [ 16.386941] ol_ath_attach() TARGET TYPE: 9 Vers 0x1000000 [ 16.392252] [ 16.392252] CE WAR Disabled [ 16.396751] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 16.402218] ol_ath_attach() configure Target . [ 16.406560] [ 16.406560] Target Version is 1000000 [ 16.411621] [ 16.411621] Flash Download Address c0000 [ 16.417275] ol_transfer_bin_file: flash data file defined [ 16.422649] Cal location [0]: 00000000 [ 16.426460] [ 16.426460] Wifi0 Select OFFSET 1000 [ 16.450421] qc98xx_verify_checksum: flash checksum passed: 0x2a61 [ 16.455482] ol_transfer_bin_file 2935: Download Flash data len 12064 [ 16.462074] Board extended Data download address: 0x0 [ 16.487191] [ 16.487222] Board data initialized [ 16.491190] Flash download ADDRESS 0xc0000 [ 16.495220] [ 16.495220] Selecting OTP binary for CHIP Version 1 [ 16.576038] [ 16.576038] First OTP send param 8000 [ 16.583536] ol_ath_download_firmware :First OTP download and Execute is good return param 38912 [ 16.591408] [ 16.591408] ##Board Id 6 [ 16.595376] [ 16.595376] ##CHIP Id 1 [ 16.599437] [ 16.599437] BOARDDATA DOWNLOAD TO address c0000 [ 16.837300] ol_transfer_bin_file: Board data file: AR900B/hw.2/boardData_AR900B_CUS240_2GMipiHigh_v2_006.bin ARXXXX v=0x1 [ 16.863917] Board extended Data download address: 0x0 [ 16.888409] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 16.894407] [ 16.894439] Selecting OTP binary for CHIP Version 1 [ 16.949671] [ 16.949703] Second otp download Param 10000 [ 16.965417] ol_ath_download_firmware : OTP download and Execute is good [ 16.971290] [ 16.971290] FIRMWARE : Beeliner CHIP Version 1 [ 16.995470] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=131072 [ 17.022149] Swap: bytes_left to copy: fw:16; dma_page:24579 [ 17.026710] Swap: wrong length read:0 [ 17.030334] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 106493 Target address 417968 [ 17.039331] scn=d9f804c0 target_write_addr=417968 seg_info=de041f10 [ 17.045704] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 17.054389] bin_filename=AR900B/hw.2/athwlan.bin swap_filename=/lib/firmware/AR900B/hw.2/athwlan.codeswap.bin open DNS error: No such file or directory [ oal_sys_getOldTZInfo ] 394: Open TZ file error! [ 18.746266] ol_ath_attach() Download FW. [ 18.749297] ol_ath_attach() HT Create . [ 18.753077] ol_ath_attach() HIF Claim. [ 18.756919] ol_ath_attach() BMI Done. [ 18.760574] ol_ath_attach() WMI attached. wmi_handle da250000 [ 18.766385] +HWT [ 18.771009] CE_recv_buf_enqueue 809 Populate last entry 512 for CE 5 [ 18.776319] CE_recv_buf_enqueue 818 CE 5 wi 511 dest_ptr 0x5b346040 nbytes 0 recv_ctxt 0xda015480 [ 18.785567] Target:db3c2000 HTC Service:0x0001, ULpipe:0 DLpipe:1 id:0 Ready [ 18.792221] -HWT [ 18.794033] [ 18.794033] <=== cfg max peer id 1056 ====> [ 18.799812] Target:db3c2000 HTC Service:0x0300, ULpipe:4 DLpipe:5 id:1 Ready [ 18.806779] HTC Service:0x0300 ep:1 TX flow control disabled [ 18.813933] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 18.819556] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from d9ad0000 [ 18.826866] Target:db3c2000 HTC Service:0x0100, ULpipe:3 DLpipe:2 id:2 Ready [ 18.833489] HTC Service:0x0100 ep:2 TX flow control disabled [ 18.839893] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 18.845860] num_rf_chain : 00000004 [ 18.849328] ht_cap_info: : 0000085b [ 18.852827] vht_cap_info : 339b79b2 [ 18.856294] vht_supp_mcs : 0000ffea [ 18.859762] ol_ath_service_ready_event: tt_support: 1 [ 18.864792] Peer Caching Enabled ; num_peers = 528, num_active_peers = 66 num_tids = 132, num_vdevs = 16 [ 18.874258] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1208 actual units 529 [ 18.882505] idx 1 req 2 num_units 1 num_unit_info 4 unit size 256 actual units 67 [ 18.889784] idx 2 req 3 num_units 1 num_unit_info 4 unit size 1024 actual units 67 [ 18.897500] idx 3 req 4 num_units 1 num_unit_info 4 unit size 4096 actual units 67 [ 18.905342] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 [ 18.913058] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 [ 18.920649] idx 6 req 5 num_units 0 num_unit_info 2 unit size 2080 actual units 529 [ 18.929084] chunk 0 len 639032 requested ,ptr 0x5a900000 [ 18.933895] chunk 1 len 17152 requested ,ptr 0x5b740000 [ 18.939300] chunk 2 len 68608 requested ,ptr 0x5a880000 [ 18.944642] chunk 3 len 274432 requested ,ptr 0x5aa00000 [ 18.950140] chunk 4 len 107520 requested ,ptr 0x5a8a0000 [ 18.955607] chunk 5 len 6144 requested ,ptr 0x5cac2000 [ 18.960918] chunk 6 len 1100320 requested ,ptr 0x5a400000 [ 19.044204] wmi_ready_event_rx: WMI UNIFIED READY event [ 19.048609] ol_ath_connect_htc() WMI is ready [ 19.052920] ol_ath_set_host_app_area TODO [ 19.057013] target uses HTT version 2.1; host uses 2.1 [ 19.066073] ol_ath_attach() connect HTC. [ 19.069040] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 19.080787] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 19.087660] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 19.094407] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 19.101249] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 19.108059] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 19.115245] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 19.122461] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 19.129740] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 19.137144] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 19.144486] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 19.151890] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 19.159418] ol_ath_phyerr_attach: called [ 19.163292] OL Resmgr Init-ed [ 19.166229] ieee80211_bsteering_attach: Band steering initialized [ 19.172258] ol_if_spectral_setup [ 19.175476] SPECTRAL : get_capability not registered [ 19.180443] HAL_CAP_PHYDIAG : Capable [ 19.184067] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 19.192158] SPECTRAL : get_capability not registered [ 19.197157] HAL_CAP_RADAR : Capable [ 19.200718] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 19.200718] (spectral_attach : 236) [ 19.210590] SPECTRAL : get_capability not registered [ 19.215495] HAL_CAP_SPECTRAL_SCAN : Capable [ 19.220868] SPECTRAL : get_tsf64 not registered [ 19.224367] spectral_init_netlink 65 NULL SKB [ 19.228709] Green-AP : Green-AP : Attached [ 19.228741] [ 19.234270] Green-AP : Attached [ 19.237394] rate power table override is only supported for AR98XX [ 19.243580] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 19.250796] ieee80211com_init_netlink: 3223: Wifipos 1st Netlink socket created:db5fd800 [ 19.258887] ol_if_dfs_setup: called [ 19.262386] ol_if_dfs_attach: called; ptr=d9545984, radar_info=db6c7be0 [ 19.269228] ol_ath_rtt_meas_report_attach: called [ 19.273820] ol_ath_attach() UMAC attach . [ 19.277819] ol_if_dfs_configure: called [ 19.281568] ol_if_dfs_configure: FCC domain [ 19.285754] ol_if_dfs_disable: called [ 19.289472] ol_ath_attach: Calling ol_if_dfs_configure [ 19.294501] [ 19.294501] BURSTING enabled by default [ 19.300031] osif_wrap_attach:400 osif wrap attached [ 19.304779] osif_wrap_devt_init:361 osif wrap dev table init done [ 19.310840] Wrap Attached: Wrap_com =db5fc800 ic->ic_wrap_com=db5fc800 &wrap_com->wc_devt=db5fc800 [ 19.319962] __ol_ath_attach: init tx/rx TODO [ 19.324179] __ol_ath_attach: needed_headroom reservation 44 [ 19.332646] ol_ath_thermal_mitigation_attach: ++ [ 19.336269] ol_ath_thermal_mitigation_attach: -- [ 19.340893] ath_pci_probe [ 19.343455] PCI device id is 0040 :0040 [ 19.347297] PCI: enabling device 0000:03:00.0 (0140 -> 0142) [ 19.353077] ath_pci 0000:03:00.0: ath DEBUG: sc=0xdb5fdc00 [ 19.358388] [ 19.358388] ol_ath_pci_configure : num_desired MSI set to 0 [ 19.365510] [ 19.365510] Using PCI Legacy Interrupt [ 19.370852] chip_id 9 chip_revision 1 [ 19.374757] [ 19.374757] address 4008f8 data db6c7c30 [ 19.381193] [ 19.381193] address 401e90 data db6c7c34 [ 19.387785] [ 19.387785] address 401e94 data db6c7c38 [ 19.394376] [ 19.394376] address 401eb0 data db6c7c3c [ 19.400968] [ 19.400968] address 400900 data db6c7c3c [ 19.407560] [ 19.407560] CLOCK PLL skipped [ 19.411152] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff [ 19.420181] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL [ 19.426491] HIF_PCIDeviceProbed: ar900b_20_targ_clk is not provided, skipping pre-configuring PLL [ 19.435332] [ 19.435332] address 4008cc data db6c7c3c [ 19.442924] __ol_ath_attach: ath_attach TODO [ 19.446204] __ol_ath_attach 1755 host_enable 0 nss_nwifi_offload 0 [ 19.452358] __ol_ath_attach: dev name wifi1 [ 19.456544] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 19.465948] OL_ACBKMinfree : 0 [ 19.469009] OL_ACBEMinfree : 0 [ 19.472133] OL_ACVIMinfree : 0 [ 19.475320] OL_ACVOMinfree : 0 [ 19.478412] ol_ath_attach() BMI inited. [ 19.482318] ol_ath_attach() BMI Get Target Info. [ 19.486816] ol_ath_attach() TARGET TYPE: 9 Vers 0x1000000 [ 19.492189] [ 19.492189] CE WAR Disabled [ 19.496688] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 19.502124] ol_ath_attach() configure Target . [ 19.506435] [ 19.506435] Target Version is 1000000 [ 19.511558] [ 19.511558] Flash Download Address c0000 [ 19.517213] ol_transfer_bin_file: flash data file defined [ 19.522586] Cal location [1]: 00004000 [ 19.526398] [ 19.526398] Wifi1 Select OFFSET 5000 [ 19.550390] qc98xx_verify_checksum: flash checksum passed: 0x2dfd [ 19.555451] ol_transfer_bin_file 2935: Download Flash data len 12064 [ 19.562011] Board extended Data download address: 0x0 [ 19.587035] [ 19.587066] Board data initialized [ 19.591034] Flash download ADDRESS 0xc0000 [ 19.595064] [ 19.595064] Selecting OTP binary for CHIP Version 1 [ 19.649828] [ 19.649828] First OTP send param 8000 [ 19.657325] ol_ath_download_firmware :First OTP download and Execute is good return param 36864 [ 19.665260] [ 19.665260] ##Board Id 4 [ 19.669165] [ 19.669165] ##CHIP Id 1 [ 19.673133] [ 19.673133] BOARDDATA DOWNLOAD TO address c0000 [ 19.679256] ol_transfer_bin_file: Board data file: AR900B/hw.2/boardData_AR900B_CUS238_5GMipiHigh_v2_004.bin ARXXXX v=0x1 [ 19.706904] Board extended Data download address: 0x0 [ 19.731271] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 19.737332] [ 19.737332] Selecting OTP binary for CHIP Version 1 [ 19.762511] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x518, 0x518, 0x0 ) [ 19.770071] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x518, 0x518, 0x0 ) [ 19.778787] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x518, 0x518, 0x0 ) [ 19.787441] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x518, 0x518, 0x0 ) [ 19.806872] [ 19.806872] Second otp download Param 10000 [ 19.822617] ol_ath_download_firmware : OTP download and Execute is good [ 19.828303] [ 19.828303] FIRMWARE : Beeliner CHIP Version 1 [ 19.851421] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=131072 [ 19.876257] Swap: bytes_left to copy: fw:16; dma_page:24579 [ 19.880849] Swap: wrong length read:0 [ 19.884473] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 106493 Target address 417968 [ 19.895470] scn=d95c04c0 target_write_addr=417968 seg_info=de2a2310 [ 19.900905] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 19.909809] bin_filename=AR900B/hw.2/athwlan.bin swap_filename=/lib/firmware/AR900B/hw.2/athwlan.codeswap.bin [ 21.025616] ol_ath_attach() Download FW. [ 21.028647] ol_ath_attach() HT Create . [ 21.032427] ol_ath_attach() HIF Claim. [ 21.036301] ol_ath_attach() BMI Done. [ 21.039893] ol_ath_attach() WMI attached. wmi_handle da040000 [ 21.045735] +HWT [ 21.050171] CE_recv_buf_enqueue 809 Populate last entry 512 for CE 5 [ 21.055482] CE_recv_buf_enqueue 818 CE 5 wi 511 dest_ptr 0x5a0aa040 nbytes 0 recv_ctxt 0xdba5c0c0 [ 21.064761] Target:db3c4800 HTC Service:0x0001, ULpipe:0 DLpipe:1 id:0 Ready [ 21.071415] -HWT [ 21.073320] [ 21.073320] <=== cfg max peer id 1056 ====> [ 21.078975] Target:db3c4800 HTC Service:0x0300, ULpipe:4 DLpipe:5 id:1 Ready [ 21.085910] HTC Service:0x0300 ep:1 TX flow control disabled [ 21.093127] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 21.097532] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from d88b0000 [ 21.105654] Target:db3c4800 HTC Service:0x0100, ULpipe:3 DLpipe:2 id:2 Ready [ 21.112433] HTC Service:0x0100 ep:2 TX flow control disabled [ 21.118900] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 21.124835] num_rf_chain : 00000004 [ 21.128272] ht_cap_info: : 0000085b [ 21.131771] vht_cap_info : 339b79b2 [ 21.135238] vht_supp_mcs : 0000ffea [ 21.138706] ol_ath_service_ready_event: tt_support: 1 [ 21.143736] Peer Caching Enabled ; num_peers = 528, num_active_peers = 66 num_tids = 132, num_vdevs = 16 [ 21.153202] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1208 actual units 529 [ 21.161449] idx 1 req 2 num_units 1 num_unit_info 4 unit size 256 actual units 67 [ 21.168666] idx 2 req 3 num_units 1 num_unit_info 4 unit size 1024 actual units 67 [ 21.176444] idx 3 req 4 num_units 1 num_unit_info 4 unit size 4096 actual units 67 [ 21.184286] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 [ 21.191971] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 [ 21.199562] idx 6 req 5 num_units 0 num_unit_info 2 unit size 2080 actual units 529 [ 21.207997] chunk 0 len 639032 requested ,ptr 0x59e00000 [ 21.212839] chunk 1 len 17152 requested ,ptr 0x5a590000 [ 21.218275] chunk 2 len 68608 requested ,ptr 0x59f00000 [ 21.223586] chunk 3 len 274432 requested ,ptr 0x59f80000 [ 21.229084] chunk 4 len 107520 requested ,ptr 0x59f20000 [ 21.234520] chunk 5 len 6144 requested ,ptr 0x5a5ce000 [ 21.239862] chunk 6 len 1100320 requested ,ptr 0x59800000 [ 21.321149] wmi_ready_event_rx: WMI UNIFIED READY event [ 21.325585] ol_ath_connect_htc() WMI is ready [ 21.329865] ol_ath_set_host_app_area TODO [ 21.333895] target uses HTT version 2.1; host uses 2.1 [ 21.344048] ol_ath_attach() connect HTC. [ 21.347079] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 21.358856] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 [ 21.365854] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 [ 21.372664] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 [ 21.379537] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 [ 21.386472] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 [ 21.393502] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 [ 21.400781] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 [ 21.408153] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 [ 21.415588] Add VHT80 channel: 5210 [ 21.419056] Add VHT80 channel: 5290 [ 21.422461] Add VHT80 channel: 5530 [ 21.425960] Add VHT80 channel: 5610 [ 21.429428] Add VHT80 channel: 5690 [ 21.432895] Add VHT80 channel: 5775 [ 21.436394] Skipping VHT80 channel 5825 [ 21.440487] ol_ath_phyerr_attach: called [ 21.444173] OL Resmgr Init-ed [ 21.448328] ieee80211_bsteering_attach: Band steering initialized [ 21.453420] ol_if_spectral_setup [ 21.456638] SPECTRAL : get_capability not registered [ 21.461574] HAL_CAP_PHYDIAG : Capable [ 21.465229] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 21.473352] SPECTRAL : get_capability not registered [ 21.478256] HAL_CAP_RADAR : Capable [ 21.481880] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 21.481880] (spectral_attach : 236) [ 21.491721] SPECTRAL : get_capability not registered [ 21.496657] HAL_CAP_SPECTRAL_SCAN : Capable [ 21.500812] SPECTRAL : get_tsf64 not registered [ 21.505310] spectral_init_netlink 65 NULL SKB [ 21.509684] Green-AP : Green-AP : Attached [ 21.509684] [ 21.515245] Green-AP : Attached [ 21.518369] rate power table override is only supported for AR98XX [ 21.524554] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 21.531740] ieee80211com_init_netlink: Socket already created db5fd800 [ 21.538269] ol_if_dfs_setup: called [ 21.541861] ol_if_dfs_attach: called; ptr=d8ac5984, radar_info=db6c7be0 [ 21.548609] ol_ath_rtt_meas_report_attach: called [ 21.553452] ol_ath_attach() UMAC attach . [ 21.557200] ol_if_dfs_configure: called [ 21.560980] ol_if_dfs_configure: FCC domain [ 21.565135] ol_if_dfs_disable: called [ 21.568853] ol_ath_attach: Calling ol_if_dfs_configure [ 21.573883] [ 21.573883] BURSTING enabled by default [ 21.579412] osif_wrap_attach:400 osif wrap attached [ 21.584161] osif_wrap_devt_init:361 osif wrap dev table init done [ 21.590253] Wrap Attached: Wrap_com =db602c00 ic->ic_wrap_com=db602c00 &wrap_com->wc_devt=db602c00 [ 21.599343] __ol_ath_attach: init tx/rx TODO [ 21.603592] __ol_ath_attach: needed_headroom reservation 44 [ 21.612027] ol_ath_thermal_mitigation_attach: ++ [ 21.615682] ol_ath_thermal_mitigation_attach: -- /bin/sh: update_smp_affinity: Permission denied [ 21.770009] set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 21.974289] ath_ioctl: SIOC80211IFCREATE CALLED [ 21.977881] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 50:c7:bf:08:60:e7: [ 21.987503] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [ 21.995064] Enabling SG bit for the vap ath0 features 4000 [ 22.000562] Enabling TSO bit for the vap ath0 features 4000 [ 22.006123] Enabling LRO bit for the vap ath0 features 4000 [ 22.011777] VAP device ath0 created osifp: (db3c6cc0) os_if: (db438000) ath0 [ 22.029147] su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 [ 22.041518] [wifi1] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x518, 0x518, 0x0 ) [ 22.049078] [wifi1] ath_ioctl: SIOC80211IFCREATE CALLED [ 22.049609] wmi_unified_vdev_create_send: ID = 1 Type = 2, Subtype = 0 VAP Addr = 52:c7:bf:08:60:e7: [ 22.049703] wmi_unified_set_psmode:set psmode=1 [ 22.050015] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [ 22.050015] Enabling SG bit for the vap ath1 features 4000 [ 22.050046] Enabling TSO bit for the vap ath1 features 4000 [ 22.050046] Enabling LRO bit for the vap ath1 features 4000 [ 22.050046] VAP device ath1 created osifp: (db5944c0) os_if: (d844c000) ath1 [ 22.099625] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( wmi_unified_set_psmode:set psmode=0 [ 22.103373] wmi_unified_set_psmode:set psmode=0 [ 22.107247] wmi_unified_set_psmode:set psmode=0 [ 22.107278] wmi_unified_set_psmode:set psmode=0 [ 22.114839] su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 [ 22.121930] ath_ioctl: SIOC80211IFCREATE CALLED [ 22.121961] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 62:c7:bf:08:60:e7: [ 22.122305] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [ 22.122336] Enabling SG bit for the vap ath2 features 4000 [ 22.122336] Enabling TSO bit for the vap ath2 features 4000 [ 22.122336] Enabling LRO bit for the vap ath2 features 4000 [ 22.122336] VAP device ath2 created osifp: (db595cc0) os_if: (da230000) ath2 [ 22.174414] 0x12, 0x1e, 0x518, 0x518, su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 [ 22.183692] 0x0 ) [ 22.185567] [wifi1] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45 [ 22.191596] DES SSID SET=TP-LINK_60E7 [ 22.195845] , 0x1e, 0x518, 0x518, 0x0 ) [ 22.199625] [wifi1] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( [ol_ath_iw_setcountry][1660] *p=44, *(p+1)=45 [ 22.203280] isCountryCodeValid: EEPROM regdomain 0x0 [ 22.203311] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 22.203311] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 22.214589] Set freq vap 0 stop send + db438000 [ 22.214589] OL vap_stop + [ 22.214620] wmi_unified_vdev_stop_send for vap 0 (da250000) [ 22.214620] OL vap_stop - [ 22.214714] Set freq vap 0 stop send -db438000 [ 22.313245] STOPPED EVENT for vap 0 (da250000) [ 22.316994] Set wait done --db438000 [ 22.316994] Set freq vap 0 stop send + d844c000 [ 22.317057] Set freq vap 0 stop send -d844c000 [ 22.329803] 0x67, 0x1e, 0x518, 0x518, 0x0 ) [ 22.339831] Set wait done --d844c000 [ 22.342361] Set freq vap 0 stop send + da230000 [ 22.347047] OL vap_stop + [ 22.349484] wmi_unified_vdev_stop_send for vap 2 (da250000) [ 22.355014] OL vap_stop - [ 22.355045] STOPPED EVENT for vap 2 (da250000) [ 22.362168] Set freq vap 0 stop send -da230000 [ 22.396626] Set wait done --da230000 [ 22.422836] ME Pool succesfully initialized vaddr - d7f00000 paddr - 0 [ 22.422836] num_elems = 10424 buf_size - 64 pool_size = 708832 [ 22.434208] Enable MCAST_TO_UCAST [ 22.452889] WARNING: Fragmentation with HT mode NOT ALLOWED!! Error for wireless request "Set Fragmentation Threshold" (8B24) : SET failed on device ath0 ; Invalid argument. [ 22.477600] Setting Max Stations:64 [ 22.511121] [ 22.511121] DES SSID SET=TP-LINK_Guest_60E7 [ 22.543142] ol_tx_me_init:Already Enabled!! [ 22.546485] Enable MCAST_TO_UCAST [ 22.561074] WARNING: Fragmentation with HT mode NOT ALLOWED!! Error for wireless request "Set Fragmentation Threshold" (8B24) : SET failed on device ath2 ; Invalid argument. [ 22.585504] Setting Max Stations:64 Reading topology file /var/Wireless/2_4G_topology.conf ... 022.881: Reading radio configuration file /var/Wireless/2_4G_80211g.ap_radio ... 022.881: Reading bss configuration file /var/Wireless/ath0.ap_bss ... [ 23.025648] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 Using interface ath0 with hwaddr 50:c7:bf:08:60:e7 and ssid 'TP-LINK_60E7' [ 23.084817] [ 23.084817] DES SSID SET=TP-LINK_60E7 023.094: upnp_wps_device_init called l2_packet_receive - recvfrom: Network is down [ 23.641424] device ath0 entered promiscuous mode atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extr[ 23.648734] device ath1 entered promiscuous mode a bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=10[ 23.661387] device ath2 entered promiscuous mode 08 left=512 plen=992 512 extra bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extra bytes in the end of netlink message *********cal_data_2g******* 202f612a0000000016000000 *********cal_data_end******* *********cal_data_5g******* 202ffd2d0000000000161616 *********cal_data_end******* /bin/sh: update_smp_affinity: Permission denied atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984 512 extra bytes in the end of netlink message [ 23.756638] set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 23.763761] [wifi0] FWLOG: [23409] WAL_DBGID_SECURITY_ENCR_EN ( 0x60e7 ) [ 23.769415] [wifi0] FWLOG: [23409] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988 512 extr[ 23.782942] ath_ioctl: SIOC80211IFCREATE CALLED a bytes in the end of netlink message [ 23.791252] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 50:c7:bf:08:60:e9: [ 23.804029] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [ 23.811715] Enabling SG bit for the vap ath5 features 4000 [ 23.817463] Enabling TSO bit for the vap ath5 features 4000 [ 23.822836] Enabling LRO bit for the vap ath5 features 4000 [ 23.828491] VAP device ath5 created osifp: (d86a3cc0) os_if: (d86cc000) ath5 atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984 512 extr[ 23.844361] ath_ioctl: SIOC80211IFCREATE CALLED a bytes in the end of netlink message [ 23.853202] wmi_unified_vdev_create_send: ID = 1 Type = 2, Subtype = 0 VAP Addr = 52:c7:bf:08:60:e9: [ 23.865760] wmi_unified_set_psmode:set psmode=1 [ 23.870415] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [ 23.878131] Enabling SG bit for the vap ath6 features 4000 [ 23.883661] Enabling TSO bit for the vap ath6 features 4000 [ 23.889378] Enabling LRO bit for the vap ath6 features 4000 [ 23.894939] VAP device ath6 created osifp: (d86a6cc0) os_if: (d8484000) ath6 atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984 512 extr[ 23.908559] wmi_unified_set_psmode:set psmode=0 a bytes in the end of net[ 23.916994] wmi_unified_set_psmode:set psmode=0 link message [ 23.927491] wmi_unified_set_psmode:set psmode=0 [ 23.931021] wmi_unified_set_psmode:set psmode=0 [ 23.938925] ath_ioctl: SIOC80211IFCREATE CALLED [ 23.942455] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 62:c7:bf:08:60:e9: [ 23.951952] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [ 23.959575] Enabling SG bit for the vap ath7 features 4000 [ 23.965073] Enabling TSO bit for the vap ath7 features 4000 [ 23.970759] Enabling LRO bit for the vap ath7 features 4000 [ 23.976413] VAP device ath7 created osifp: (d86a34c0) os_if: (d84a8000) ath7 atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984 512 extr[ 23.992127] [ 23.992127] DES SSID SET=TP-LINK_60E7_5G a bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988 512 extr[ 24.011090] [ol_ath_iw_setcountry][1660] *p=44, *(p+1)=45 [ 24.019462] isCountryCodeValid: EEPROM regdomain 0x0 [ 24.024367] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 a bytes in the end of netlink message [ 24.031521] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 [ 24.041674] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 [ 24.048578] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 [ 24.055420] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 [ 24.062480] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 [ 24.069759] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 [ 24.077163] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 [ 24.084536] Add VHT80 channel: 5210 [ 24.088003] Add VHT80 channel: 5290 [ 24.091471] Add VHT80 channel: 5530 [ 24.094939] Add VHT80 channel: 5610 [ 24.098437] Skipping VHT80 channel 5660 [ 24.102218] Skipping VHT80 channel 5680 [ 24.106091] Skipping VHT80 channel 5700 atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988 512 extra bytes in the end of netlink message [ 24.121680] Set freq vap 0 stop send + d86cc000 [ 24.129115] OL vap_stop + [ 24.131677] wmi_unified_vdev_stop_send for vap 0 (da040000) [ 24.137300] OL vap_stop - [ 24.137363] STOPPED EVENT for vap 0 (da040000) [ 24.144329] Set freq vap 0 stop send -d86cc000 [ 24.176632] Set wait done --d86cc000 [ 24.179162] Set freq vap 0 stop send + d8484000 [ 24.183723] Set freq vap 0 stop send -d8484000 [ 24.216651] Set wait done --d8484000 [ 24.219181] Set freq vap 0 stop send + d84a8000 [ 24.223680] OL vap_stop + [ 24.226304] wmi_unified_vdev_stop_send for vap 2 (da040000) [ 24.231833] OL vap_stop - [ 24.234489] STOPPED EVENT for vap 2 (da040000) [ 24.234489] Set freq vap 0 stop send -d84a8000 [ 24.256638] Set wait done --d84a8000 [ 24.282724] ME Pool succesfully initialized vaddr - d8200000 paddr - 0 [ 24.282724] num_elems = 10424 buf_size - 64 pool_size = 708832 [ 24.294095] Enable MCAST_TO_UCAST [ 24.312839] WARNING: Fragmentation with HT mode NOT ALLOWED!! Error for wireless request "Set Fragmentation Threshold" (8B24) : SET failed on device ath5 ; Invalid argument. [ 24.340674] Setting Max Stations:64 [ 24.374445] [ 24.374445] DES SSID SET=TP-LINK_Guest_60E7_5G [ 24.407372] ol_tx_me_init:Already Enabled!! [ 24.410527] Enable MCAST_TO_UCAST [ 24.425304] WARNING: Fragmentation with HT mode NOT ALLOWED!! Error for wireless request "Set Fragmentation Threshold" (8B24) : SET failed on device ath7 ; Invalid argument. [ 24.450015] Setting Max Stations:64 Reading topology file /var/Wireless/5G_topology.conf ... 024.492: Reading radio configuration file /var/Wireless/5G_80211g.ap_radio ... 024.493: Reading bss configuration file /var/Wireless/ath5.ap_bss ... [ 24.575663] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 Using interface ath5 with hwaddr 50:c7:bf:08:60:e9 and ssid 'TP-LINK_60E7_5G' [ 24.634676] [ 24.634676] DES SSID SET=TP-LINK_60E7_5G 024.644: upnp_wps_device_init called l2_packet_receive - recvfrom: Network is down starting pid 1024, tty '': '/sbin/getty -L ttyHSL1 115200 vt100' [ 25.041205] [wifi1] FWLOG: [24955] WAL_DBGID_SECURITY_ENCR_EN ( 0x60e9 ) [ 25.046860] [wifi1] FWLOG: [24955] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) Archer VR2600v login: [ 25.504342] device ath5 entered promiscuous mode atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extr[ 25.511715] device ath6 entered promiscuous mode a bytes in the end of netlink message atheros_wireless_event_re[ 25.524835] device ath7 entered promiscuous mode ceive:Malformed netlink message: len=1008 left=512 plen=992 512 extra bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extra bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extra bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extra bytes in the end of netlink message atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992 512 extra bytes in the end of netlink message sendto: No such file or directory pid 1023 send 2030 error sendto: No such file or directory pid 1023 send 2004 error iptables: Bad rule (does a matching rule exist in that chain?). radvd starting [setBusinessSocks : 131] g_sockvoiceapp = -1 [ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid. [ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid. [ 27.975320] [ 27.975320] tplink_deaccelerate_all OK. iptables: Bad rule (does a matching rule exist in that chain?). [ 27.996532] [ 27.996532] tplink_deaccelerate_all OK. iptables: Bad rule (does a matching rule exist in that chain?)[ 28.009621] [ 28.009621] tplink_deaccelerate_all OK. . Archer VR2600v login: iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:497 ether.dst=8e164851c142 /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:500 ether.proto=dd01 /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:497 ether.dst=8e164851c142 /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:500 ether.proto=dd03 /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:1083 [0;31mrecv ack thread start[0m /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:497 ether.dst=8e164851c142 /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:500 ether.proto=dd02 [ rsl_setStorageServiceObj ] 1394: mountFlag is 3,We start usb server killall: minidlnad: no process killed Archer VR2600v login: adminiptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). [ 32.397719] kcg 333 :GPL NetUSB up! [ 32.434489] kc 90 : run_telnetDBGDServer start [ 32.438238] kc 227 : init_DebugD end [ 32.441830] INFO17ED: NetUSB 1.02.67, 00030467 : May 15 2015 16:22:12 [ 32.448422] INFO17EF: 7437: Archer VR2600v :Archer VR2600v [ 32.453795] INFO17F0: AUTH ISOC [ 32.457044] INFO17F1: filterAudio [ 32.460668] usbcore: registered new interface driver KC NetUSB General Driver [ 32.469665] INFO0145: init proc : PAGE_SIZE 4096 [ 32.469665] INFO16E1: infomap bf799bc4 [ 32.469665] INFO16E4: sleep to wait br0 to wake up [ 32.482193] INFO15B4: tcpConnector() started... : br0 SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. Enable forwarding Password: [ 32.589784] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000 [ 32.595813] . [ 32.597094] erase successed! [ 32.599968] [ 32.601437] Write to flash:0xf90000, len is 0x1f5e [ 32.945204] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000 [ 32.951171] . [ 32.952514] erase successed! [ 32.955388] [ 32.956919] Write to flash:0xf90000, len is 0x1f5e [ 33.304467] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000 [ 33.310434] . [ 33.311777] erase successed! [ 33.314651] [ 33.316151] Write to flash:0xf90000, len is 0x1f5e [ 33.669790] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000 [ 33.675726] . [ 33.677100] erase successed! [ 33.679975] [ 33.681443] Write to flash:0xf90000, len is 0x1f5e [ 34.034051] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000 [ 34.040018] . [ 34.041362] erase successed! [ 34.044236] [ 34.045735] Write to flash:0xf90000, len is 0x1f5e [ 34.392564] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000 [ 34.398531] . [ 34.399875] erase successed! [ 34.402780] [ 34.404248] Write to flash:0xf90000, len is 0x1f5e firm version:1.1.0 0.8.0 v004f.0 Build 160215 Rel.30334n hard version:Archer VR2600v v1 00000000 firm version:1.1.0 0.8.0 v004f.0 Build 160215 Rel.30334n hard version:Archer VR2600v v1 00000000
OpenWrt bootlog
Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.18.26 (trondah@ff0) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r48524) ) #1 SMP PREEMPT Sun Feb 14 13:44:33 UTC 2016 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TP-Link Archer C2600 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 9 pages/cpu @ddc17000 s7360 r8192 d21312 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 481224K/491520K available (3669K kernel code, 261K rwdata, 1468K rodata, 180K init, 289K bss, 10296K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff000000 ( 520 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc070c848 (5139 kB) [ 0.000000] .init : 0xc070d000 - 0xc073a000 ( 180 kB) [ 0.000000] .data : 0xc073a000 - 0xc077b778 ( 262 kB) [ 0.000000] .bss : 0xc077b778 - 0xc07c3e60 ( 290 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000011] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 687194767200ns [ 0.000028] Switching to timer-based delay loop, resolution 160ns [ 0.000169] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000192] pid_max: default: 32768 minimum: 301 [ 0.000356] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000377] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001008] CPU: Testing write buffer coherency: ok [ 0.001295] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001827] Setting up static identity map for 0x42212a28 - 0x42212a80 [ 0.084085] CPU1: Booted secondary processor [ 0.084214] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.084337] Brought up 2 CPUs [ 0.084361] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.084373] CPU: All CPU(s) started in SVC mode. [ 0.098556] VFP support v0.3: implementor 51 architecture 0 part 4d variant 2 rev 0 [ 0.099072] pinctrl core: initialized pinctrl subsystem [ 0.099555] regulator-dummy: no parameters [ 0.107424] NET: Registered protocol family 16 [ 0.107674] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.134534] cpuidle: using governor ladder [ 0.165549] cpuidle: using governor menu [ 0.180106] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 0.180181] qcom_rpm 108000.rpm: failed to mark ack irq as wakeup [ 0.180245] qcom_rpm 108000.rpm: failed to mark wakeup irq as wakeup [ 0.208896] smb208-s1a: 1050 <--> 1150 mV [ 0.209283] smb208-s1b: 1050 <--> 1150 mV [ 0.209646] smb208-s2a: 800 <--> 1250 mV [ 0.209994] smb208-s2b: 800 <--> 1250 mV [ 0.210543] pps_core: LinuxPPS API ver. 1 registered [ 0.210560] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.210614] PTP clock support registered [ 0.212017] Switched to clocksource dg_timer [ 0.213671] NET: Registered protocol family 2 [ 0.214567] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.214610] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.214665] TCP: Hash tables configured (established 4096 bind 4096) [ 0.214717] TCP: reno registered [ 0.214746] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.214770] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.215019] NET: Registered protocol family 1 [ 0.216589] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.226079] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.226105] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.227146] msgmni has been set to 939 [ 0.228823] io scheduler noop registered [ 0.228849] io scheduler deadline registered (default) [ 0.230137] 1b500000.pci supply vdda not found, using dummy regulator [ 0.230238] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.230328] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.260219] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.260249] pci_bus 0000:00: root bus resource [io 0xfe00000-0xfffff] (bus address [0x1fc00000-0xfefffff]) [ 0.260268] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.260288] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.260916] PCI: bus0: Fast back to back transfers disabled [ 0.263085] PCI: bus1: Fast back to back transfers disabled [ 0.263279] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.263305] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.263424] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.263447] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.264443] 1b700000.pci supply vdda not found, using dummy regulator [ 0.264545] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.264638] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.294714] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.294740] pci_bus 0001:00: root bus resource [io 0x31e10000-0xfffff] (bus address [0x63c00000-0x31eeffff]) [ 0.294757] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.294775] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.295330] PCI: bus0: Fast back to back transfers disabled [ 0.297364] PCI: bus1: Fast back to back transfers disabled [ 0.297628] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.297653] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.297765] pci 0001:00:00.0: PCI bridge to [bus 01] [ 0.297789] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.301074] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.302420] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0 [ 0.303449] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.304559] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.304668] msm_serial 16340000.serial: uartclk = 1843200 [ 0.304738] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 184, base_baud = 115200) is a MSM [ 0.304800] msm_serial: console setup on port #0 [ 0.946805] console [ttyMSM0] enabled [ 0.951643] msm_serial: driver initialized [ 0.956896] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.958863] of_dma_request_slave_channel: dma-names property of node '/soc/gsbi@1a200000/spi@1a280000' missing or empty [ 0.967734] m25p80 spi32766.0: found mx25u25635f, expected s25fl256s1 [ 0.976800] m25p80 spi32766.0: mx25u25635f (32768 Kbytes) [ 0.983385] 13 qcom-smem partitions found on MTD device spi32766.0 [ 0.988630] Creating 13 MTD partitions on "spi32766.0": [ 0.994786] 0x000000000000-0x000000020000 : "0:SBL1" [ 1.000931] 0x000000020000-0x000000040000 : "0:MIBIB" [ 1.006099] 0x000000040000-0x000000060000 : "0:SBL2" [ 1.010953] 0x000000060000-0x000000090000 : "0:SBL3" [ 1.016078] 0x000000090000-0x0000000a0000 : "0:DDRCONFIG" [ 1.020964] 0x0000000a0000-0x0000000b0000 : "0:SSD" [ 1.026290] 0x0000000b0000-0x0000000e0000 : "0:TZ" [ 1.030943] 0x0000000e0000-0x000000100000 : "0:RPM" [ 1.035851] 0x000000100000-0x000000170000 : "0:APPSBL" [ 1.040530] 0x000000170000-0x0000001b0000 : "0:APPSBLENV" [ 1.045833] 0x0000001b0000-0x0000001f0000 : "0:ART" [ 1.051219] 0x0000001f0000-0x0000003f0000 : "0:HLOS" [ 1.056040] 0x0000003f0000-0x000001ef0000 : "rootfs" [ 1.061127] mtd: device 12 (rootfs) set to be root filesystem [ 1.065520] 1 squashfs-split partitions found on MTD device rootfs [ 1.070753] 0x000000ce0000-0x000001ef0000 : "rootfs_data" [ 1.078688] libphy: Fixed MDIO Bus: probed [ 1.082881] libphy: GPIO Bitbanged MDIO: probed [ 1.106906] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 1.332025] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 1.332056] Ring mode enabled [ 1.336152] DMA HW capability register supported [ 1.339007] Enhanced/Alternate descriptors [ 1.343779] Enabled extended descriptors [ 1.347773] RX Checksum Offload Engine supported (type 2) [ 1.351941] TX Checksum insertion supported [ 1.357408] Wake-Up On Lan supported [ 1.361826] Enable RX Mitigation via HW Watchdog Timer [ 1.367002] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 1.370345] Ring mode enabled [ 1.375637] DMA HW capability register supported [ 1.378502] Enhanced/Alternate descriptors [ 1.383274] Enabled extended descriptors [ 1.387268] RX Checksum Offload Engine supported (type 2) [ 1.391437] TX Checksum insertion supported [ 1.396895] Wake-Up On Lan supported [ 1.401323] Enable RX Mitigation via HW Watchdog Timer [ 1.405692] i2c /dev entries driver [ 1.411065] Speed bin: 0 [ 1.413395] PVS bin: 1 [ 1.416567] platform cpufreq-krait.0: Driver cpufreq-krait requests probe deferral [ 1.420249] L2 @ QSB rate. Forcing new rate. [ 1.426139] L2 @ 387500 KHz [ 1.430380] CPU0 @ 800000 KHz [ 1.432825] CPU1 @ QSB rate. Forcing new rate. [ 1.435972] CPU1 @ 384000 KHz [ 1.440691] TCP: cubic registered [ 1.444342] NET: Registered protocol family 10 [ 1.448129] NET: Registered protocol family 17 [ 1.450987] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.455500] Bridge firewalling registered [ 1.468174] 8021q: 802.1Q VLAN Support v1.8 [ 1.472081] Registering SWP/SWPB emulation handler [ 1.483537] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.490670] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19 [ 1.498694] VFS: Mounted root (squashfs filesystem) readonly on device 31:12. [ 1.498855] Freeing unused kernel memory: 180K (c070d000 - c073a000) [ 2.113873] random: nonblocking pool is initialized [ 3.468545] init: Console is alive [ 3.468676] init: - watchdog - [ 7.054165] usbcore: registered new interface driver usbfs [ 7.054237] usbcore: registered new interface driver hub [ 7.058628] usbcore: registered new device driver usb [ 7.065333] exFAT: Version 1.2.9 [ 7.078020] genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 337 [ 7.078090] gpio-keys gpio-keys: failed to request irq:337 for gpio:49 [ 7.085085] genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 352 [ 7.091283] gpio-keys gpio-keys: failed to request irq:352 for gpio:64 [ 7.099424] genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 353 [ 7.105679] gpio-keys gpio-keys: failed to request irq:353 for gpio:65 [ 7.113730] genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 304 [ 7.119922] gpio-keys gpio-keys: failed to request irq:304 for gpio:16 [ 7.130405] SCSI subsystem initialized [ 7.140528] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.140968] ehci-platform: EHCI generic platform driver [ 7.148702] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.151514] ohci-platform: OHCI generic platform driver [ 7.660326] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 7.660374] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 7.665009] xhci-hcd xhci-hcd.0.auto: irq 142, io mem 0x11000000 [ 7.672896] hub 1-0:1.0: USB hub found [ 7.678528] hub 1-0:1.0: 1 port detected [ 7.682278] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 7.686222] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 7.691951] hub 2-0:1.0: USB hub found [ 7.699081] hub 2-0:1.0: 1 port detected [ 7.703120] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 7.706903] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 7.712436] xhci-hcd xhci-hcd.1.auto: irq 237, io mem 0x10000000 [ 7.720203] hub 3-0:1.0: USB hub found [ 7.726075] hub 3-0:1.0: 1 port detected [ 7.729740] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 7.733683] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 7.739421] hub 4-0:1.0: USB hub found [ 7.746567] hub 4-0:1.0: 1 port detected [ 7.753083] usbcore: registered new interface driver usb-storage [ 8.482073] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.091309] mount_root: loading kmods from internal overlay [ 15.016653] jffs2: notice: (81) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 15.018409] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 15.058231] block: extroot: not configured [ 15.356231] jffs2: notice: (78) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 15.364762] mount_root: loading kmods from internal overlay [ 17.476226] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 17.516449] block: extroot: not configured [ 17.543722] mount_root: switching to jffs2 overlay [ 17.556055] procd: - early - [ 17.556112] procd: - watchdog - [ 18.231352] procd: - ubus - [ 19.247714] procd: - init - Please press Enter to activate this console. [ 20.049645] Initializing XFRM netlink socket [ 20.050431] NET: Registered protocol family 15 [ 20.054074] tun: Universal TUN/TAP device driver, 1.6 [ 20.057231] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 20.071571] sit: IPv6 over IPv4 tunneling driver [ 20.076547] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 20.081788] Netfilter messages via NETLINK v0.30. [ 20.083017] ip_set: protocol 6 [ 20.097509] cryptodev: driver 1.8 loaded. [ 20.100026] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68 [ 20.100496] Backport generated by backports.git backports-20151218-0-g2f58d9d [ 20.166420] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 20.167160] ath10k_pci 0000:01:00.0: pci irq msi interrupts 1 irq_mode 0 reset_mode 0 [ 21.061053] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002 [ 21.061089] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 21.070756] ath10k_pci 0000:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01 [ 23.112415] ath10k_pci 0000:01:00.0: unable to read from the device [ 23.112444] ath10k_pci 0000:01:00.0: could not execute otp for board id check: -110 [ 23.117486] ath10k_pci 0000:01:00.0: failed to get board id from otp: -110, ignoring [ 23.138737] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 23.138948] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 7e56fd07 [ 24.539760] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 24.599871] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 24.600636] ath10k_pci 0001:01:00.0: pci irq msi interrupts 1 irq_mode 0 reset_mode 0 [ 24.739265] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002 [ 24.739300] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 24.749173] ath10k_pci 0001:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01 [ 26.792392] ath10k_pci 0001:01:00.0: unable to read from the device [ 26.792421] ath10k_pci 0001:01:00.0: could not execute otp for board id check: -110 [ 26.797462] ath10k_pci 0001:01:00.0: failed to get board id from otp: -110, ignoring [ 26.805296] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 26.813245] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 7e56fd07 [ 28.217337] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 28.282686] u32 classifier [ 28.282705] input device check on [ 28.284278] Actions configured [ 28.288921] Mirror/redirect action on [ 28.295842] nf_conntrack version 0.5.0 (7521 buckets, 30084 max) [ 28.314818] ip_tables: (C) 2000-2006 Netfilter Core Team [ 28.315899] usbcore: registered new interface driver ipheth [ 28.422006] xt_time: kernel timezone is -0000 [ 28.425030] usbcore: registered new interface driver cdc_ether [ 28.430052] PPP generic driver version 2.4.2 [ 28.431822] NET: Registered protocol family 24 [ 28.436700] usbcore: registered new interface driver rndis_host [ 32.197032] eth1: device MAC address 00:03:7f:ba:db:02 [ 32.217280] device eth1 entered promiscuous mode [ 32.220931] br-lan: port 1(eth1) entered forwarding state [ 32.220977] br-lan: port 1(eth1) entered forwarding state [ 32.247040] eth0: device MAC address 00:03:7f:ba:db:01 [ 33.804236] ath10k_pci 0001:01:00.0: DFS region 0x0 not supported, will trigger radar for every pulse [ 33.804291] ath10k_pci 0000:01:00.0: DFS region 0x0 not supported, will trigger radar for every pulse [ 34.212398] br-lan: port 1(eth1) entered forwarding state [ 34.779462] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 34.779518] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 37.743397] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 37.831495] ath10k_pci 0001:01:00.0: no channel configured; ignoring frame(s)! [ 37.937463] ath10k_pci 0001:01:00.0: no channel configured; ignoring frame(s)! [ 38.365438] ath10k_pci 0001:01:00.0: no channel configured; ignoring frame(s)! [ 39.032987] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 39.033482] device wlan1 entered promiscuous mode [ 39.047202] device wlan0 entered promiscuous mode [ 39.203749] ath10k_pci 0001:01:00.0: no channel configured; ignoring frame(s)! [ 39.611628] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 39.611817] br-lan: port 2(wlan1) entered forwarding state [ 39.617151] br-lan: port 2(wlan1) entered forwarding state [ 40.015740] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 40.015855] br-lan: port 3(wlan0) entered forwarding state [ 40.021192] br-lan: port 3(wlan0) entered forwarding state [ 40.036383] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready [ 40.118596] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [ 41.612396] br-lan: port 2(wlan1) entered forwarding state [ 42.013015] br-lan: port 3(wlan0) entered forwarding state
Notes
Known differences between Hardware VR2600/VR2600v and C2600
- Flash chip used in VR2600v is smaller (16MB)
- Flash layout (partitions) are different
- The labelled LAN ports do not correspond to the LAN ports as seen within 21.02.3 LuCI. Bug Report 10275 Fixed in 21.02.4 and 22.03.0.
- The VR2600/VR2600V is known to suffer from sporadic_reboots as seen on similar TP-Link C2600. A partial fix implemented starting from 23.05.x Commit
- There has been reports of wifi problems with the TP-Link C2600 in the past with early CT wifi drivers, so you may wish to install alternative_wifi_module_and_firmware