[OpenWrt Wiki] TP-Link Archer C6 v2

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== TP-Link Archer C6 v2======

{{media:tplink:archer_c6.jpg?400|Archer C6}}

<WRAP important 100%>**Warning** The 5 GHz radio / Qualcomm Atheros QCA9886 support seems to be buggy in some cases.

Some users report much improved long-term stability with 5 GHz by using the ath10k firmware instead of the ath10k-ct firmware.
To do this remove the packages "kmod-ath10k-ct" and "ath10k-firmware-qca9888-ct" and instead install "kmod-ath10k" and "ath10k-firmware-qca9888".
</WRAP>

===== Supported Versions =====
<!-- ToH: {
  "source": "json",
  "dom": "t",
  "paging": false,
  "rotate": true,
  "shownColumns": ["brand", "model", "version", "supportedcurrentrel", "oemdevicehomepageurl", "forumsearch", "deviceid"],
  "filterColumns": {"brand": "^TP-Link$", "model": "^Archer C6$", "version": "^v2.*$"}
} -->


===== Hardware Highlights =====
<!-- ToH: {
  "source": "json",
  "dom": "t",
  "paging": false,
  "rotate": true,
  "shownColumns": ["model", "version", "cpu", "cpumhz", "flashmb", "rammb", "wlanhardware", "wlan24ghz", "wlan50ghz", "ethernet100mports", "ethernet1gports", "modem", "usbports"],
  "filterColumns": {"brand": "^TP-Link$", "model": "^Archer C6$", "version": "^v2.*$"}
} -->


===== Installation =====
<!-- ToH: {
  "source": "json",
  "dom": "t",
  "paging": false,
  "rotate": true,
  "shownColumns": ["model", "version", "supportedcurrentrel", "firmwareopenwrtinstallurl", "firmwareopenwrtupgradeurl", "firmwareoemstockurl"],
  "filterColumns": {"brand": "^TP-Link$", "model": "^Archer C6$", "version": "^v2.*$"}
} -->

-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]

==== Flash using web interface ====

<WRAP dangerous>
Flashing OpenWrt through the OEM web interface is not always possible: the OpenWrt factory image needs to have the correct magic that matches the OEM firmware version.  So, depending on the OEM firmware version, different versions of OpenWrt can be installed through the OEM web interface:

^ OEM firmware  ^ OpenWrt version accepted by OEM web interface                    ^
| 1.0.X         | 18.06.X, 19.07.0                                                 |
| 1.1.X         | 19.07.1 and later, master                                        |
| 1.2.0, 1.2.1  | 19.07.2 and master fails "invalid type"                          |
| 1.3.3         | 23.05.3 flashes successfully                                     |
| 1.3.4         | 19.07.4 flashes successfully                                     |
| 1.3.5         | 19.07.5 flashes successfully                                     |
| 1.3.6         | 19.07.4 flashes successfully, 21.02, 23.05 flashes successfully  |

This is going to be a pain, expect a patch to generate factory images for several OEM firmware versions eventually.

It is possible to bypass this check by flashing via the bootloader's TFTP recovery mode, however several steps and a lot of tries are necessary to get everything right, as the link training window is extremely tight. For more information, see the Flash using TFTP recovery section below.
</WRAP>

If your OEM firmware supports it, simply upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface.

==== Flash using TFTP recovery ====

<WRAP dangerous>
An ethernet switch between the router and the TFTP server should be used in order to prevent the TFTP server's interface to shutdown!\\
If the server's interface shuts down, the router times out and it won't find the TFTP server (see unsuccessful log output below).
</WRAP>

  - Connect to your router's WAN port (it doesn't work with LAN ports!) to a network switch or a computer
  - Connect another cable from the switch to the computer/TFTP server (or directly)
  - Set the computer IP to 192.168.0.66
  - Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin
  - Connect the power cable to the router, press and hold the reset button and turn the router on
  - Keep the reset button pressed until the WPS LED lights up
  - Wait ~150 seconds until flashing and booting is completed

If you're having TFTP time out, it is caused by taking too long to negotiate the link. Use 10/100MBit switch. see Post [[https://forum.openwrt.org/t/cant-boot-tftp-recovery-archer-c6-v2/36487/26]].


//Unsuccessful TFTP recovery bootlog://\\
<WRAP bootlog>
<nowiki>U-Boot 1.1.4 (Jun 26 2018 - 19:41:08)

ap152 - Dragonfly 1.0

DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 375k for U-Boot at: 87fa0000
Reserving 8256k for malloc() at: 87790000
Reserving 44 Bytes for Board Info at: 8778ffd4
Reserving 36 Bytes for Global Data at: 8778ffb0
Reserving 128k for boot params() at: 8776ffb0
Stack Pointer at: 8776ff98
Now running in RAM - U-Boot at: 87fa0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200 
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x60c02100
run command setenv serverip 192.168.0.66;setenv ipaddr 192.168.0.86
run command tftp 0x80060000 ArcherC6v2_tp_recovery.bin
Trying eth0
eth0 link down
FAIL
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'ArcherC6v2_tp_recovery.bin'.
Load address: 0x80060000
Loading: * * Tx Timed out
T Tx Timed out
T Tx Timed out
Tftp server tranfer fail!
tftpboot firmware failed, now start normally.
Hit any key to stop autoboot:  1 0
</nowiki>
</WRAP>
\\
//Successful TFTP recovery bootlog://\\
<WRAP bootlog>
<nowiki>U-Boot 1.1.4 (Jun 26 2018 - 19:41:08)

ap152 - Dragonfly 1.0

DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 375k for U-Boot at: 87fa0000
Reserving 8256k for malloc() at: 87790000
Reserving 44 Bytes for Board Info at: 8778ffd4
Reserving 36 Bytes for Global Data at: 8778ffb0
Reserving 128k for boot params() at: 8776ffb0
Stack Pointer at: 8776ff98
Now running in RAM - U-Boot at: 87fa0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200 
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x60c02100
run command setenv serverip 192.168.0.66;setenv ipaddr 192.168.0.86
run command tftp 0x80060000 ArcherC6v2_tp_recovery.bin
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'ArcherC6v2_tp_recovery.bin'.
Load address: 0x80060000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ##########################################################
done
Bytes transferred = 4618908 (467a9c hex)
Firmware downloaded... filesize = 0x467a9c fileaddr = 0x80060000.
Firmware Recovery file length : 4618908



Firmware process common.



Image verify OK!



Firmware file Verify ok!



[Error]sysmgr_proinfo_buildStruct():  659 @ unknown id(device_name), skip it.


[Error]sysmgr_proinfo_buildStruct():  659 @ unknown id(country), skip it.


[Error]sysmgr_proinfo_buildStruct():  659 @ unknown id(hw_ver), skip it.


Firmware supports, check OK.



Firmware Recovery check ok!



######################################################################

#######

Done.

Firmware Recovery Success!



All Done!
now restart...
</nowiki>
</WRAP>
\\
->  [[docs:guide-user:installation:generic.flashing.tftp]]

If the router doesn't seem to load the TFTP image maybe try the following script:
<code>
#/bin/bash
USER=yourusername
IFNAME=yourinterface
ip address flush dev $IFNAME
ip address add 192.168.0.66/24 dev $IFNAME
ip link set $IFNAME up
dnsmasq -i $IFNAME --dhcp-range=192.168.0.100,192.168.0.150 \
--dhcp-boot=ArcherC6v2_tp_recovery.bin \
--enable-tftp --tftp-root=/home/$USER/openwrt -d -u $USER -p0 -K --log-dhcp --bootp-dynamic
</code>

===== Debricking =====
-> [[docs:guide-user:troubleshooting:generic.debrick]]

===== Recover via serial and tftp (working uboot) =====

Set the IP of the tftp server to YOURIP. Ensure firewall (port 69, UDP) is open.

Start tftp server, e.g.
<code>
sudo dnsmasq -kd -p 0 -C /dev/null -u nobody --enable-tftp --tftp-root=/PATH/TO/BIN/FILE/
</code>

<WRAP Dangerous>
Please Note: Partitioning For US and EU Versions is different! The example below flashes the firmware in the corresponding partition address for the EU version(0x9f030000). If you are flashing the US version, 0x9f030000 is actually the u-boot partition. Using the below example as is in a US version Archer C6/A6 will overwrite the u-boot partition.  When Flashing the US version, substitute 0x9f030000 with 0x9f050000 in the code shown below.
</WRAP>

<code>
setenv serverip YOURIP
tftpboot 0x80060000 openwrt-19.07.2-ath79-generic-tplink_archer-c6-v2-squashfs-sysupgrade.bin
-> Bytes transferred = 4653342 (47011e hex) <-- if another version is used, change the size in the commands below to match the new size
erase 0x9f030000 +47011e
cp.b 0x80060000 0x9f030000 0x47011e
bootm 0x9f030000
</code>


===== Failsafe mode =====
-> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset]]

===== Back to stock firmware =====

See [[https://forum.openwrt.org/t/tp-link-archer-c6-v2-revert-to-stock-firmware-guide/96416?u=tmomas|Tp-Link Archer C6 V2 Revert to Stock Firmware]]

===== Basic configuration =====
-> [[docs:guide-user:base-system:start|Basic configuration]] After flashing, proceed with this.\\
Set up your Internet connection, configure wireless, configure USB port, etc.

===== Hardware =====
==== Info ====
<!-- ToH: {
  "source": "json",
  "dom": "t",
  "paging": false,
  "rotate": true,
  "shownColumns": ["brand", "model", "version", "devicetype", "availability", "supportedsincecommit", "supportedsincerel", "supportedcurrentrel", "unsupported_functions", "bootloader", "target", "cpumhz", "flashmb", "rammb", "switch", "ethernet100mports", "ethernet1gports", "commentsnetworkports", "modem", "vlan", "wlan24ghz", "wlan50ghz", "wlanhardware", "wlancomments", "detachableantennas", "usbports", "sataports", "commentsusbsataports", "serial", "jtag", "ledcount", "buttoncount", "powersupply", "deviceid", "owrt_forum_topic_url", "wikideviurl", "oemdevicehomepageurl", "firmwareoemstockurl", "firmwareopenwrtinstallurl", "firmwareopenwrtupgradeurl", "comments"],
  "filterColumns": {"brand": "^TP-Link$", "model": "^Archer C6$", "version": "^v2.*$"}
} -->

SPI Chip: GigaDevices GD25Q64C (25Q64CS16)


==== Photos ====
/* =====>>>>> Standard size for photos: add ?400 to the medialink                                */
/* When uploading photos, **name them** intelligently. Nobody knows what 20100930_000602.jpg is! */
/* e.g. {{:media:yourbrand:yourbrand_yourmodel_front.jpg?400|}}                                  */
/* Thanks, your wiki administration - Oct. 2015 */

//Front://\\
{{:media:tplink:tplink_archer_c6_front.jpg?400|}}

//Back://\\
{{:media:tplink:tplink_archer_c6_back.jpg?400|}}

//Backside label://\\
{{:media:tplink:tplink_archer_c6_under.jpg?400|}}

==== Opening the case ====

**Note:** This will void your warranty!

  * Remove two screws located at the bottom of the device
  * Pry open the shiny top. The top is really tight. Opening it will most likely break some plastic inside and will void your warranty. Perhaps this is intentional. PCB is located a good 2-3cm away from the edges in front and sides so you can use some gorilla power to get it open.

//Clips://\\
{{:media:tplink:archer_c6_top_clips.jpg?400|}}


//PCB front://\\
{{:media:tplink:tplink_archer_c6_inside.jpg?400|}}

//PCB back://\\
{{:media:tplink:archer_c6_pcb_back.jpg?400|}}
There are no pins or pads below the aluminium heat sink, just two thermal pads and three shake proof washers as distance holders

==== Serial ====
-> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:\\
\\
RX and GND testpoints are easy to access.\\
For TX testpoint:\\
1. Remove metal protection from main CPU\\
2. Then cut middle metal reinforcements\\
\\
{{media:tplink:archer_c6_v2_serial_points.jpg?400|}}


^ Serial connection parameters\\ for TP-Link Archer C6 v2 | 115200, 8N1\\ its bootloader U-boot sets speed to about 120000 bps,\\ kernel downs a little,\\ when kernel serial driver is started it is set to standart 115200)|

==== JTAG ====
-> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:\\
**Insert photo of PCB with markings for JTAG port**

===== Flash layout =====
^  [[toh:tp-link:archer_c6_v2|TP-Link Archer C6 V2 (EU/RU/JP)]] Flash Layout                                                                                                                                                                                                                                                                                                                                                         ||||||||
^ Layer0                                                                      |  raw SPI NOR flash memory chip (**GD25Q64C** [[wp>Serial Peripheral Interface Bus|spi]]0.0: [[https://www.elm-tech.com/ja/products/spi-flash-memory/gd25q64/gd25q64.pdf|GD25Q64C]]) 8192 KiB                                                                                                                                                          |||||||
^ Layer1                                                                      |  mtd0 **//u-boot//** 128 KiB                                                                                                                                                                  | mtd1 **//info//** 64 KiB|   mtd2 **//firmware//** 7808 KiB                                                                                             |||  mtd6 **//tplink//** 128 KiB  |  mtd7 **//art//** 64 KiB  |
^ Layer2                                                                      |                                                                                                                                                                                               | | mtd3 **//kernel//** 2191 KiB (*)    |  mtd4 **//rootfs//** 5616 KiB (*)                                                             ||                           |
^ <color magenta>mountpoint</color>                                           |                                                                                                                                                                                               | |                                 |  <color magenta>''/''</color>                                                             ||                           |
^ filesystem                                                                  |                                                                                                                                                                                               | |                                 |  [[docs:techref:filesystems#overlayfs|OverlayFS]]                                         ||                           |
^ Layer3                                                                      |                                                                                                                                                                                               | |                                 |                                                    |  mtd5 **//rootfs_data//** 1408 KiB    |                           |
^ Size in KiB                                                                 |  128 KiB                                                                                                                                                                                      |  64 KiB  |  2191 KiB (*)                       |  4208 KiB (*)                                         |  1408 KiB (*)                            |  128 KiB  |  64 KiB                   |
^ Name                                                                        |  **//u-boot//**                                                                                                                                                                               |  **//info//**  |  **//kernel//**                  |   **//rootfs//**                                  |  **//rootfs_data//**                  |  **//tplink//**  |  **//art//**              |
^ <color magenta>mountpoint</color>                                           |  //none//                                                                                                                                                                                     | |  //none//                        |  <color magenta>''/rom''</color>                   |  <color magenta>''/overlay''</color>  |  //none//                 |  //none//  |
^ filesystem                                                                  |  //none//                                                                                                                                                                                     | |  //none//                        |  [[docs:techref:filesystems#SquashFS]]             |  [[docs:techref:filesystems#JFFS2]]   |  //none//                 |  //none//  |
**''(*) mtd3,4 and 5 sizes depend on release/snapshot. Here is example for 22.03.2
''**
[[:supported_devices:864_warning#analysis_of_firmware_size_growth|analysis_of_firmware_size_growth]], [[https://github.com/openwrt/openwrt/issues/11417|#11417]]
<hidden>
FIXME //verify flash layout.//
|    | "u-boot"        |    |

| Start-End Address on Flash chip | Name |
| 0x000000-0x030000 | "u-boot" |
| 0x030000-0x130000 | "uImage" |
| 0x130000-0x7e0000 | "rootfs", set to be root filesystem |
| 0x7f0000-0x800000 | "ART" |

FIXME //verify mtd paritions, might be OEM firmware, maybe add values from /var/env/ //

root@ArcherC6v2:/# cat /proc/mtd

| dev | size | erasesize | name |
| mtd0 | 00030000 | 00010000 | "u-boot" |
| mtd1 | 00100000 | 00010000 | "uImage" |
| mtd2 | 006b0000 | 00010000 | "rootfs" |
| mtd3 | 00010000 | 00010000 | "ART" |
</hidden>

===== Bootloader mods =====
-> [[docs:techref:bootloader]]

===== Hardware mods =====

==== Potential USB 2.0 support ====

The main IC QCA9563 (under the metal shield) supports "Two USB 2.0 Host controllers with built-in MAC/PHY", however on the PCB, the pins are not connected to anything (except for VDD12_PLL_USB).

The following pins might be used for USB:

  * (Pin B43) VDD12_PLL_USB (connected to VCC?)
  * (Pin A55) USB_DP1 (**not connected**)
  * (Pin B42) USB_DM1 (**not connected**)
  * (Pin A53) VDD12_PLL_USB (connected to VCC?)
  * (Pin B40) USB_DP0 (**not connected**)
  * (Pin A52) USB_DM0 (**not connected**)

However is is extremely hard to connect the pins since the pin distance is only 0.5mm/0.026inches.

{{media:tplink:archer_c6_v2_usb_pins.jpg?600|}}


===== Bootlogs =====
==== OEM bootlog ====
<WRAP bootlog>
<nowiki>
U-Boot 1.1.4 (Jun 26 2018 - 19:41:08)

ap152 - Dragonfly 1.0

DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 375k for U-Boot at: 87fa0000
Reserving 8256k for malloc() at: 87790000
Reserving 44 Bytes for Board Info at: 8778ffd4
Reserving 36 Bytes for Global Data at: 8778ffb0
Reserving 128k for boot params() at: 8776ffb0
Stack Pointer at: 8776ff98
Now running in RAM - U-Boot at: 87fa0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200 
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x60c02100
Hit any key to stop autoboot:  1  0 
## Booting image at 9f030000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2019-09-04   9:13:21 UTC
   Image Type:   MIPS Linux Multi-File Image (lzma compressed)
   Data Size:    1046676 Bytes = 1022.1 kB
   Load Address: 80060000
   Entry Point:  80060000
   Contents:
   Image 0:  1046668 Bytes = 1022.1 kB
   Verifying Checksum at 0x9f030040 ...OK
   Uncompressing Multi-File Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 3.3.8 (leo@leo-MS-7529) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sat Aug 31 20:43:49 CST 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros QCA956X rev 0
[    0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00008000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00008000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  console=ttyS0,115200 board=AP152 rootfstype=squashfs init=/etc/preinit mtdparts=spi0.0:192k(u-boot),1024k(uImage),6848k(rootfs),64k@0x7f0000(ART) mem=128M rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 126344k/131072k available (2232k kernel code, 4728k reserved, 553k data, 180k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:83
[    0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.070000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[    0.080000] MIPS: machine is TP-LINK Archer c6 v2 eu support
[    0.080000] registering PCI controller with io_map_base unset
[    0.290000] bio: create slab <bio-0> at 0
[    0.300000] PCI host bridge to bus 0000:00
[    0.300000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    0.310000] pci_bus 0000:00: root bus resource [io  0x0001]
[    0.310000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.320000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.320000] Switching to clocksource MIPS
[    0.330000] NET: Registered protocol family 2
[    0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.330000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.340000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.340000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.350000] TCP reno registered
[    0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.360000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.360000] NET: Registered protocol family 1
[    0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.380000] msgmni has been set to 246
[    0.390000] io scheduler noop registered
[    0.390000] io scheduler deadline registered (default)
[    0.400000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.420000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.430000] console [ttyS0] enabled, bootconsole disabled
[    0.430000] console [ttyS0] enabled, bootconsole disabled
[    0.440000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.450000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.450000] 4 cmdlinepart partitions found on MTD device spi0.0
[    0.460000] Creating 4 MTD partitions on "spi0.0":
[    0.460000] 0x000000000000-0x000000030000 : "u-boot"
[    0.470000] 0x000000030000-0x000000130000 : "uImage"
[    0.480000] 0x000000130000-0x0000007e0000 : "rootfs"
[    0.480000] mtd: partition "rootfs" set to be root filesystem
[    0.490000] 0x0000007f0000-0x000000800000 : "ART"
[    0.490000] flash_chrdev : flash_chrdev_init 
[    0.640000] ag71xx_mdio: probed
[    0.640000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.190000] ag71xx_probe:not calling:ag71xx_phy_connect
[    1.200000] TCP cubic registered
[    1.200000] NET: Registered protocol family 17
[    1.210000] Bridge firewalling registered
[    1.210000] 8021q: 802.1Q VLAN Support v1.8
[    1.220000] ### of_selftest(): No testcase data in device tree; not running tests
[    1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.240000] Freeing unused kernel memory: 180k freed
[    3.250000] ag71xx_open DEFINED AR8216_PHY_RESET_CMD!
[    3.280000] eth0: Atheros AR8327 switch driver attached.
[    3.290000] before HW reset reg[e0]: [c74164de] -> [c74164de]
[    3.300000] before HW reset reg[10]: [602613a0] -> [602613a0]
[    4.400000] recovery reg[e0]: [c70164c0] -> [c74164de]
[    4.410000] recovery reg[10]: [261320] -> [602613a0]
[    7.340000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
- preinit -
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
[    7.850000] in ag71xx_stop
[    7.850000] ag71xx_stop:ag71xx_phy_disconnect
[    8.630000] liblog: module license 'unspecified' taints kernel.
[    8.640000] Disabling lock debugging due to kernel taint
[    8.950000] NET: Registered protocol family 10
[    9.380000] Button Hotplug driver version 0.4.1
[    9.410000] PPP generic driver version 2.4.2
[    9.480000] tun: Universal TUN/TAP device driver, 1.6
[    9.490000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    9.530000] PPP MPPE Compression module registered
[    9.550000] NET: Registered protocol family 24
[    9.630000] L2TP core driver, V2.0
[    9.650000] L2TP netlink interface
[    9.730000] IPv6 over IPv4 tunneling driver
[    9.790000] GRE over IPv4 demultiplexor driver
[    9.810000] GRE over IPv4 tunneling driver
[    9.940000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.060000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[   10.200000] PPPoL2TP kernel driver, V2.0
[   10.270000] PPTP driver version 0.8.5
[   10.690000] xt_time: kernel timezone is -0000
[   11.100000] nf_conntrack_rtsp v0.6.21 loading
[   11.120000] nf_nat_rtsp v0.6.21 loading
[   11.210000] Netfilter messages via NETLINK v0.30.
[   11.280000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.350000] ctnetlink v0.93: registering with nfnetlink.
[   11.610000] ssdk_plat_init start
[   11.620000] Register QCA PHY driver
[   11.740000] qca-ssdk module init succeeded!
reload_profile() begin:
reload_profile() end:
reloadconfig() begin:
user-config size OK:8853
result is 
0
reloadconfig() end:
mergeconfigbycountry() begin
user has set country
mergeconfigbycountry() do nothing end

Please press Enter to activate this console. [   15.290000] ag71xx_open DEFINED AR8216_PHY_RESET_CMD!ar8216_config_init, 2804:  qca_qm_err_recovery 
[   15.300000] before HW reset reg[e0]: [c74164de] -> [c74164de]
[   15.310000] before HW reset reg[10]: [602613a0] -> [602613a0]
[   16.420000] recovery reg[e0]: [c70164c0] -> [c74164de]
[   16.430000] recovery reg[10]: [261320] -> [602613a0]
[   18.370000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[   18.380000] ADDRCONF(NETDEV_UP): eth0: link is not ready
GMT+00:00	
Mon Oct 14 00:00:00 GMT 2019
[SWITCH DEBUG] Clear Port(0) PVID
[SWITCH DEBUG] Clear Port(1) PVID
[SWITCH DEBUG] Clear Port(2) PVID
[SWITCH DEBUG] Clear Port(3) PVID
[SWITCH DEBUG] Clear Port(4) PVID
[SWITCH DEBUG] Clear Port(5) PVID
[SWITCH DEBUG] Flush vlan entries.
[SWITCH DEBUG] Create VLAN VID=1
[SWITCH DEBUG] Add tagged port(0) to VLAN(1)
[SWITCH DEBUG] Add untagged port(2) to VLAN(1)
[SWITCH DEBUG] Add untagged port(3) to VLAN(1)
[SWITCH DEBUG] Add untagged port(4) to VLAN(1)
[SWITCH DEBUG] Add untagged port(5) to VLAN(1)
[SWITCH DEBUG] Set Port(0) PVID(1)
[SWITCH DEBUG] Set Port(0) ingress to secure
[SWITCH DEBUG] Set Port(2) PVID(1)
[SWITCH DEBUG] Set Port(2) ingress to secure
[SWITCH DEBUG] Set Port(3) PVID(1)
[SWITCH DEBUG] Set Port(3) ingress to secure
[SWITCH DEBUG] Set Port(4) PVID(1)
[SWITCH DEBUG] Set Port(4) ingress to secure
[SWITCH DEBUG] Set Port(5) PVID(1)
[SWITCH DEBUG] Set Port(5) ingress to secure
[SWITCH DEBUG] Create VLAN VID=4094
[SWITCH DEBUG] Add tagged port(0) to VLAN(4094)
[SWITCH DEBUG] Add untagged port(1) to VLAN(4094)
[SWITCH DEBUG] Set Port(0) PVID(4094)
[SWITCH DEBUG] Set Port(0) ingress to secure
[SWITCH DEBUG] Set Port(1) PVID(4094)
[SWITCH DEBUG] Set Port(1) ingress to secure
[SWITCH DEBUG] Set Port(0) PVID(0)
[   20.390000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   20.400000] eth0: link up (1000Mbps/Full duplex)
[   20.780000] device eth0 entered promiscuous mode
[   22.530000] ar8216_read_status_3156: eth0.4094 carrier off!port_vlan_id = 4094
Loading defaults
[   27.000000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
[   27.290000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
Loading synflood protection
[   27.600000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
Adding custom chains
[   29.270000] __ath_attach: Set global_scn[0]
[   29.270000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
[   29.280000] ACBKMinfree = 48
[   29.280000] ACBEMinfree = 32
[   29.290000] ACVIMinfree = 16
[   29.290000] ACVOMinfree = 0
[   29.290000] CABMinfree = 48
[   29.300000] UAPSDMinfree = 0
[   29.300000] ATH_TXBUF=2700
[   29.310000] Enterprise mode: 0x03bda000
[   29.320000] Restoring Cal data from DRAM
[   29.320000] 
[   29.320000] ART Version : -48.0.0
[   29.320000] SW Image Version : -48.0.0.0.0
[   29.330000] Board Revision :  
[   29.330000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125 
[   29.340000] ath_get_caps[6328] rx chainmask mismatch actual 7 sc_chainmak 0
[   29.350000] ath_get_caps[6303] tx chainmask mismatch actual 7 sc_chainmak 0
[   29.370000] ath_tx_paprd_init sc 872d8000 PAPRD disabled in HAL
[   29.380000] wifi0: Atheros 956X: mem=0xb8100000, irq=47
[   29.380000] ath_pci:  (Atheros/multi-bss)
[   29.390000] ol_ath_pci_probe: PCI device id 0056 :0056
[   29.390000] ath_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[   29.400000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   29.410000]  *********** Besra *************
[   29.410000] 
[   29.410000] __ol_ath_attach() Allocated scn 86180380
[   29.420000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x87ae5800
[   29.420000] 
[   29.420000]  ol_ath_pci_configure : num_desired MSI set to 0
[   29.430000] 
[   29.430000]  Using PCI Legacy Interrupt
[   29.440000] chip_id 0xc chip_revision 0x0 
[   29.450000] 
[   29.450000]  CLOCK PLL skipped 
[   29.460000] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff
[   29.470000] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL
[   29.480000] __ol_ath_attach: dev name wifi1
[   29.480000] ol_ath_attach interface_id 1
[   29.480000] ol_ath_attach() BMI inited.
[   29.620000] ol_ath_attach() BMI Get Target Info.
[   29.620000] Chip id: 0xc, chip version: 0x1000000
[   29.620000] 
[   29.620000]  CE WAR Disabled
[   29.650000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
[   29.660000] ol_ath_attach() configure Target .
[   29.660000] 
[   29.660000]  Target Version is 1000000
[   29.670000] 
[   29.670000]  Flash Download Address  c0000 
[   29.670000] ol_transfer_bin_file: flash data file defined
[   29.680000] Cal location [0]: 00004000
[   29.680000] 
[   29.680000]  wifi1 NAND FLASH Select OFFSET 0x5000
[   29.720000] qc98xx_verify_checksum: flash checksum passed: 0xa329
[   29.730000] ol_transfer_bin_file 3451: Download Flash data len 12064
[   29.750000] Board extended Data download address: 0x0
[   29.770000] 
[   29.770000]  Board data initialized
[   29.800000] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
[   29.800000] 
[   29.800000]  Selecting  OTP binary for CHIP Version 0
[   30.070000] ol_transfer_bin_file 3271: downloading file 0, Download data len 8964
[   30.110000] 
[   30.110000]  First OTP send param 8000
Loading zones
[   30.360000] ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660
[   30.370000] ol_ath_download_firmware:##Board Id 20 , CHIP Id 0
[   30.380000] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
[   30.380000] Warning : No board id matched. Selecting default boarddata file
[   30.390000] 
[   30.390000]  wifi1: Selecting board data file name boarddata_0.bin
[   30.400000] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boarddata_0.bin
[   30.440000] ol_transfer_bin_file 3271: downloading file 3, Download data len 12064
[   30.470000] Board extended Data download address: 0x0
[   30.500000] ol_ath_download_firmware: Using 0x1234 for the remainder of init
[   30.500000] 
[   30.500000]  Selecting  OTP binary for CHIP Version 0
[   30.550000] ol_transfer_bin_file 3271: downloading file 0, Download data len 8964
[   30.620000] 
[   30.620000]  [Flash] : Ignore Module param
[   30.630000] 
[   30.630000]  Second otp download Param 10000 
[   30.890000] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 
[   30.900000] 
[   30.900000]  Mission mode: Firmware CHIP Version 0
[   30.940000] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 
[   31.030000] Swap: bytes_left to copy: fw:16; dma_page:61485
[   31.030000] Swap: wrong length read:0
[   31.040000] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 200659 Target address 419530 
[   31.050000] scn=86180380  target_write_addr=419530 seg_info=8696d410 
[   31.060000] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 
[   31.070000] bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin 
[   31.080000] ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
[   31.680000] ol_transfer_bin_file 3271: downloading file 1, Download data len 354424
Loading forwardings
[   32.270000] device eth0 left promiscuous mode
[   32.290000] del ct event: 2 dev_name: eth0.4094
[   32.300000]  start clean up ct iterate..
Loading rules
[   32.320000] device eth0 entered promiscuous mode
[   32.320000] ADDRCONF(NETDEV_UP): lo: link is not ready
[   32.350000] @@@@@@ add br-lan!!!
[   32.350000] del ct event: 2 dev_name: eth0.1
[   32.360000]  start clean up ct iterate..
[   32.390000] device eth0.1 entered promiscuous mode
[   32.390000] br-lan: port 1(eth0.1) entered forwarding state
[   32.400000] br-lan: port 1(eth0.1) entered forwarding state
[   32.410000] [4m[ changeLanIp ] 1438: changeLanIp to 0xc0a80001
[   32.410000] [0mLoading redirects
Loading includes
Optimizing conntrack
Loading interfaces
ar8216_read_status_3156: eth0.4094 carrier off!port_vlan_id = 4094
[   33.380000] ar8216_read_status_3156: eth0.1 carrier off!port_vlan_id = 1
[   33.390000] br-lan: port 1(eth0.1) entered disabled state
[   33.640000] ol_ath_attach() Download FW done. 
[   33.640000] ol_ath_attach() HT Create .
[   33.650000] ol_ath_attach() HIF Claim.
[   33.660000] ol_ath_attach() BMI Done. 
[   33.660000] ol_ath_attach 7556 host_enable 0 nss_nwifi_offload 0
[   33.670000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
[   33.670000]  OL_ACBKMinfree : 0
[   33.680000]  OL_ACBEMinfree : 0
[   33.680000]  OL_ACVIMinfree : 0
[   33.680000]  OL_ACVOMinfree : 0
[   33.690000] ol_ath_attach() WMI attached. wmi_handle 86230000 
[   33.700000] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5
[   33.700000] CE_recv_buf_enqueue 886 CE 5 wi 511 dest_ptr 0x63ef820 nbytes 0 recv_ctxt 0x863de300
[   33.710000] Startup Mode-0 set
[   33.720000] 
[   33.720000] <=== cfg max peer id 1056 ====>
[   33.730000] HTC Service:0x0300 ep:1 TX flow control disabled
[   33.730000] htt_peer_map_timer_init Enter pdev 85c78000 hrtimer 85c7c7c0
[   33.740000] 
[   33.740000]  htt_alloc_peer_map_mem : Alloc Success : host q vaddr 87176000 paddr 7176000
[   33.750000] 
[   33.750000]  htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
[   33.760000] CE_pkt_dl_len_set CE 4 Pkt download length 64
[   33.770000] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 85920000
[   33.780000] HTC Service:0x0100 ep:2 TX flow control disabled
[   33.780000] wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event 
[   33.790000] Firmware_Build_Number:99 
[   33.790000] host/RAM_fw Build Ver Mismatch: H:0x5D, F:0x63 ! 
[   33.800000] num_rf_chain:0x00000002  ht_cap_info:0x0000085b  vht_cap_info:0x339979f2  vht_supp_mcs:0x0000fffa
[   33.810000] 
[   33.810000]  RES CFG Support wmi_service_bitmap 9778 
[   33.820000] 
[   33.820000]  Sending Ext resource cfg: HOST PLATFORM as 1 and fw_feature_bitmap as 50 to TGT 
[   33.830000] ol_ath_service_ready_event: tt_support: 1
[   33.830000] ol_ath_service_ready_event: periodic_chan_stats: 0
[   33.840000] Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17
[   33.850000] idx 1 req 2  num_units 1 num_unit_info 12 unit size 256 actual units 53 
[   33.860000] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,
[   33.860000] idx 2 req 3  num_units 1 num_unit_info 12 unit size 1024 actual units 53 
[   33.870000] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,
[   33.880000] idx 3 req 4  num_units 1 num_unit_info 12 unit size 4096 actual units 53 
[   33.890000] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,
[   33.900000] idx 0 req 1  num_units 0 num_unit_info 2 unit size 872 actual units 531 
[   33.910000] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 265 unit_len 872,
[   33.910000] ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 266 unit_len 872,
[   33.920000] idx 4 req 5  num_units 0 num_unit_info 2 unit size 1892 actual units 531 
[   33.930000] ol_ath_alloc_host_mem_chunk req_id 5 idx 5 num_units 132 unit_len 1892,
[   33.940000] ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 133 unit_len 1892,
[   33.950000] ol_ath_alloc_host_mem_chunk req_id 5 idx 7 num_units 133 unit_len 1892,
[   33.960000] ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 133 unit_len 1892,
[   33.970000] chunk 0 len 13568 requested ,ptr  0x5908000 
[   33.970000] chunk 1 len 54272 requested ,ptr  0x5910000 
[   33.980000] chunk 2 len 217088 requested ,ptr  0x5940000 
[   33.980000] chunk 3 len 231080 requested ,ptr  0x5980000 
[   33.990000] chunk 4 len 231952 requested ,ptr  0x59c0000 
[   34.000000] chunk 5 len 249744 requested ,ptr  0x5a00000 
[   34.000000] chunk 6 len 251636 requested ,ptr  0x5a40000 
[   34.010000] chunk 7 len 251636 requested ,ptr  0x5a80000 
[   34.010000] chunk 8 len 251636 requested ,ptr  0x5ac0000 
[   34.040000] wmi_ready_event_rx:  WMI UNIFIED READY event 
[   34.050000] ol_ath_connect_htc() WMI is ready
[   34.050000] target uses HTT version 2.2; host uses 2.2
[   34.060000] ol_ath_attach() connect HTC. 
[   34.070000] bypasswmi : 0
[   34.070000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
[   34.080000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
[   34.090000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
[   34.090000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
[   34.100000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
[   34.110000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
[   34.120000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
[   34.120000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
[   34.130000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
[   34.140000] Add VHT80 channel: 5210
[   34.140000] Add VHT80 channel: 5290
[   34.150000] Add VHT80 channel: 5530
[   34.150000] Add VHT80 channel: 5610
[   34.150000] Add VHT80 channel: 5690
[   34.160000] Add VHT80 channel: 5775
[   34.160000] Skipping VHT80 channel 5825
[   34.170000] OL Resmgr Init-ed
[   34.170000] rate power table override is only supported for AR98XX
[   34.180000] ol_ath_attach() UMAC attach . 
[   34.180000] 
[   34.180000]  BURSTING enabled by default
[   34.190000] __ol_ath_attach: needed_headroom reservation 44
[   34.200000] ol_ath_thermal_mitigation_attach: --
[   34.650000] [wifi1] FWLOG: [39880] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[   34.660000] [wifi1] FWLOG: [39880] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[   34.670000] [wifi1] FWLOG: [39880] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[   34.680000] [wifi1] FWLOG: [39880] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[   34.690000] [wifi1] FWLOG: [39880] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )
[   36.210000]  start clean up ct iterate..
Loading tpcmd
[   37.040000] Switching to Tx Mode-0
loading access_control
[   37.450000] wlan_vap_create : enter. devhandle=0x871f0380, opmode=IEEE80211_M_HOSTAP, flags=0x3
[   37.450000] 
[   37.460000] ieee80211_mbo_vattach:MBO Initialized 
[   37.470000] wlan_vap_create : exit. devhandle=0x871f0380, opmode=IEEE80211_M_HOSTAP, flags=0x3.
[   37.470000] 
[   37.480000] VAP device ath0 created osifp: (86292380) os_if: (85b08000)
[   37.570000] siwfreq
[   37.570000] Set freq vap 0 stop send + 85b08000
[   37.580000] Set freq vap 0 stop send -85b08000
[   37.610000] Set wait done --85b08000
loading basic_security
[   37.710000] Not supported in this vap 
[   37.820000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
[   37.870000] siwfreq
[   37.880000] Set freq vap 0 stop send + 85b08000
[   37.880000] Set freq vap 0 stop send -85b08000
[   37.940000] Set wait done --85b08000
[   38.440000]  
[   38.440000]  DES SSID SET= 
[   38.460000]  
[   38.460000]  DES SSID SET=TP-Link_XXXX 
[   39.640000]  ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 
[   39.650000]  DEVICE IS DOWN ifname=ath0
[   39.650000]  DEVICE IS DOWN ifname=ath0
[   39.840000] Warning: node not in table 0x86171000
[   39.930000] 8021q: adding VLAN 0 to HW filter on device ath0
[   42.610000] [ol_ath_iw_setcountry][1680] *p=44, *(p+1)=45
[   42.610000] isCountryCodeValid: EEPROM regdomain 0x0
[   42.620000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
[   42.620000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
[   42.630000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
[   42.640000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
[   42.650000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
[   42.650000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
[   42.660000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
[   42.670000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
[   42.700000] ieee80211_extap_detect_stop: stop.
[   42.770000] Add VHT80 channel: 5210
[   42.770000] Add VHT80 channel: 5290
[   42.780000] Add VHT80 channel: 5530
[   42.780000] Add VHT80 channel: 5610
[   42.980000] set TXBF_SND_PERIOD: value 100 wmi_status 0
[   43.080000] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 0c:80:63:a0:8a:6c:
[   43.090000] ieee80211_mbo_vattach:MBO Initialized 
[   43.100000] VAP device ath1 created osifp: (86212b80) os_if: (86008000)
[   43.170000] siwfreq
[   43.170000] Set freq vap 0 stop send + 86008000
[   43.180000] Set freq vap 0 stop send -86008000
[   43.210000] Set wait done --86008000
[   43.240000] siwfreq
[   43.240000] Set freq vap 0 stop send + 86008000
[   43.250000] Set freq vap 0 stop send -86008000
[   43.280000] Set wait done --86008000
[   43.350000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
[   43.380000] siwfreq
[   43.380000] Set freq vap 0 stop send + 86008000
[   43.390000] Set freq vap 0 stop send -86008000
[   43.420000] Set wait done --86008000
[   43.560000] ME Pool succesfully initialized vaddr - 85000000 paddr - 0
[   43.560000] num_elems = 1424 buf_size - 64 pool_size = 102528
[   43.570000] Enable MCAST_TO_UCAST
[   43.660000] [wifi1] FWLOG: [48946] WAL_DBGID_DEV_RESET ( 0xc01d, 0x47b )
[   43.770000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[   43.990000] su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1
[   44.000000] su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1
[   44.070000] su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1
[   44.150000]  
[   44.150000]  DES SSID SET= 
[   44.160000]  
[   44.160000]  DES SSID SET=TP-Link_8A6D_5G 
[   45.130000]  ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 
[   45.140000]  DEVICE IS DOWN ifname=ath1
[   45.140000]  DEVICE IS DOWN ifname=ath1
[   45.340000] 8021q: adding VLAN 0 to HW filter on device ath1
[   45.660000] [wifi1] FWLOG: [51425] WAL_DBGID_SECURITY_ENCR_EN (  )
[   45.670000] [wifi1] FWLOG: [51425] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
[   45.670000] [wifi1] FWLOG: [51450] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1
[   45.680000] [wifi1] FWLOG: [51764] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1
[   46.560000] wmi_unified_vdev_down_send for vap 0 (86230000)
[   46.570000] ieee80211_extap_detect_stop: stop.
[   46.570000] ACS failed to derive the channel. So,selecting channel with least BSS 
[   46.580000] random channel is 48 
[   46.600000] ******** ACS report ******** 
[   46.600000]  Channel | BSS  | minrssi | maxrssi | NF | Ch load | spect load | sec_chan 
[   46.610000] ---------------------------------------------------------------------
[   46.620000]  5180( 36)   10       23        35   -105       6           0          1   
[   46.620000]  5200( 40)    4       14        21   -106       2           0          1   
[   46.630000]  5220( 44)    8        4        33   -105       4           0          1   
[   46.640000]  5240( 48)    0        0         0   -105       1           0          1   
[   46.650000] OL vap_start +
[   46.650000] wmi_unified_vdev_start_send for vap 0 (86230000)
[   46.660000] OL vap_start -
[   46.660000] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
[   46.840000] [wifi1] FWLOG: [52078] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1
[   46.850000] [wifi1] FWLOG: [52392] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1
[   46.860000] [wifi1] FWLOG: [52713] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[   46.870000] [wifi1] FWLOG: [52713] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[   46.870000] [wifi1] FWLOG: [52802] vap-0 VDEV_MGR_VDEV_START ( 0x1478, 0x2, 0x0, 0x0 )
[   46.880000] [wifi1] FWLOG: [52802] WAL channel change freq=5240, mode=10 flags=0 rx_ok=1 tx_ok=1
[   46.890000] ol_vdev_start_resp_ev for vap 0 (86230000)
[   46.900000] su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1
[   46.900000] wmi_unified_vdev_up_send for vap 0 (86230000)
[   47.070000] Lan Domain: tplinklogin.net
[   47.080000] Lan Domain: www.tplinklogin.net
[   47.320000] device ath0 entered promiscuous mode
[   47.320000] br-lan: port 2(ath0) entered forwarding state
[   47.330000] br-lan: port 2(ath0) entered forwarding state
[   47.430000] device ath1 entered promiscuous mode
[   47.440000] br-lan: port 3(ath1) entered forwarding state
[   47.440000] br-lan: port 3(ath1) entered forwarding state
[   47.840000] [wifi1] FWLOG: [53061] VDEV_MGR_HP_START_TIME ( 0x0, 0x1478, 0xc4e000 )
[   47.850000] [wifi1] FWLOG: [53061] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
[   47.860000] [wifi1] FWLOG: [53061] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[   47.860000] [wifi1] FWLOG: [53061] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x1478, 0x0, 0x0 )
[DEBUG] dnsmasq flock before
[DEBUG]: Read config file lines: # auto-generated config file from /etc/config/dhcp

[DEBUG]: Read config file lines: conf-file=/etc/dnsmasq.conf

[DEBUG]: Read config file lines: # Change the following lines if you want dnsmasq to serve SRV

[DEBUG]: Read config file lines: # records.

[DEBUG]: Read config file lines: # You may add multiple srv-host lines.

[DEBUG]: Read config file lines: # The fields are <name>,<target>,<port>,<priority>,<weight>

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: # A SRV record sending LDAP for the example.com domain to

[DEBUG]: Read config file lines: # ldapserver.example.com port 289

[DEBUG]: Read config file lines: #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: # Two SRV records for LDAP, each with different priorities

[DEBUG]: Read config file lines: #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1

[DEBUG]: Read config file lines: #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: # A SRV record indicating that there is no LDAP server for the domain

[DEBUG]: Read config file lines: # example.com

[DEBUG]: Read config file lines: #srv-host=_ldap._tcp.example.com

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: # The following line shows how to make dnsmasq serve an arbitrary PTR

[DEBUG]: Read config file lines: # record. This is useful for DNS-SD.

[DEBUG]: Read config file lines: # The fields are <name>,<target>

[DEBUG]: Read config file lines: #ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services"

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: # Change the following lines to enable dnsmasq to serve TXT records.

[DEBUG]: Read config file lines: # These are used for things like SPF and zeroconf.

[DEBUG]: Read config file lines: # The fields are <name>,<text>,<text>...

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: #Example SPF.

[DEBUG]: Read config file lines: #txt-record=example.com,"v=spf1 a -all"

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: #Example zeroconf

[DEBUG]: Read config file lines: #txt-record=_http._tcp.example.com,name=value,paper=A4

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: # Provide an alias for a "local" DNS name. Note that this _only_ works

[DEBUG]: Read config file lines: # for targets which are names from DHCP or /etc/hosts. Give host

[DEBUG]: Read config file lines: # "bert" another name, bertrand

[DEBUG]: Read config file lines: # The fields are <cname>,<target>

[DEBUG]: Read config file lines: #cname=bertand,bert

[DEBUG]: Read config file lines: cname=tplinklogin.net,tplinkwifi.net

[DEBUG]: Read config file lines: dhcp-authoritative

[DEBUG]: Read config file lines: domain-needed

[DEBUG]: Read config file lines: localise-queries

[DEBUG]: Read config file lines: read-ethers

[DEBUG]: Read config file lines: bogus-priv

[DEBUG]: Read config file lines: expand-hosts

[DEBUG]: Read config file lines: server=/lan/

[DEBUG]: Read config file lines: dhcp-leasefile=/tmp/dhcp.leases

[DEBUG]: Read config file lines: resolv-file=/tmp/resolv.conf.auto

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: dhcp-range=lan,192.168.0.100,192.168.0.199,255.255.255.0,120m

[DEBUG]: Read config file lines: dhcp-option=lan,3,192.168.0.1

[DEBUG]: Read config file lines: no-dhcp-interface=eth0.4094

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: 

[DEBUG]: Read config file lines: address=/ArcherC6v2/192.168.0.1

[DEBUG]: Read config file lines: ptr-record=1.0.168.192.in-addr.arpa,ArcherC6v2

[DEBUG] dnsmasq flock end
[   52.850000]  start clean up ct iterate..
Normal env generate
Flush nat forwarding chain
loading administration management
loading with https
fw unload_local_mgnt
loading parental_control
uci try old hw_enable:
uci: Entry not found

 SSDK Init OK![   55.740000] enable:1
[   55.740000] bg task init successfull!
[   55.740000] host_helper_init start
[   55.750000] /proc/qca_switch/nf_athrs17_hnat is created
[   55.760000] /proc/qca_switch/nf_athrs17_hnat_wan_type is created
[   55.760000] /proc/qca_switch/nf_athrs17_hnat_ppp_id is created
[   55.770000] /proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
[   55.780000] /proc/qca_switch/nf_athrs17_hnat_wan_ip is created
[   55.780000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
[   55.790000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
[   55.800000] /proc/qca_switch/nf_athrs17_hnat_wan_mac is created
[   55.800000] /proc/qca_switch/nf_athrs17_hnat_ppp_id2 is created
[   55.810000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
[   55.820000] host_helper_init, wifi_dev_vid =-1, reset it
[   55.820000] enable nat_hw_prv_base_update
[   55.820000] no pppoe dev
[   55.830000] Adding ACL rules 15 - upnp_ssdp_add_acl_rules
[   55.850000] ACL is not yet enabled. Enabling... 
[   55.860000] Adding ACL rules 7 - ipv6_snooping_solicted_node_add_acl_rules
[   55.910000] Adding ACL rules 11 - ipv6_snooping_sextuple0_group_add_acl_rules
[   55.960000] Adding ACL rules 13 - ipv6_snooping_quintruple0_1_group_add_acl_rules
[   56.010000] Hello, nat helper module for 1.1!
[   56.030000] register inet_notifier###

operate done.

HNAT STARTED---
start_instance() main
generate key: 1825 1024
[LEO]uhttpd start
phyport start .......
SETUP port (1) duplex: 1000 full autoneg: on!
[   63.240000] fast-classifier: starting up
[   63.250000] fast-classifier: registered
SFE STARTED---
true
exit status value = [0x0]
dut is_cal==true.
dhcp_hook_d not load
loading qos
wifi check in.



BusyBox v1.19.4 (2019-09-04 18:17:57 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

     MM           NM                    MMMMMMM          M       M
   $MMMMM        MMMMM                MMMMMMMMMMM      MMM     MMM
  MMMMMMMM     MM MMMMM.              MMMMM:MMMMMM:   MMMM   MMMMM
MMMM= MMMMMM  MMM   MMMM       MMMMM   MMMM  MMMMMM   MMMM  MMMMM'
MMMM=  MMMMM MMMM    MM       MMMMM    MMMM    MMMM   MMMMNMMMMM
MMMM=   MMMM  MMMMM          MMMMM     MMMM    MMMM   MMMMMMMM
MMMM=   MMMM   MMMMMM       MMMMM      MMMM    MMMM   MMMMMMMMM
MMMM=   MMMM     MMMMM,    NMMMMMMMM   MMMM    MMMM   MMMMMMMMMMM
MMMM=   MMMM      MMMMMM   MMMMMMMM    MMMM    MMMM   MMMM  MMMMMM
MMMM=   MMMM   MM    MMMM    MMMM      MMMM    MMMM   MMMM    MMMM
MMMM$ ,MMMMM  MMMMM  MMMM    MMM       MMMM   MMMMM   MMMM    MMMM
  MMMMMMM:      MMMMMMM     M         MMMMMMMMMMMM  MMMMMMM MMMMMMM
    MMMMMM       MMMMN     M           MMMMMMMMM      MMMM    MMMM
     MMMM          M                    MMMMMMM        M       M
       M
 ---------------------------------------------------------------
   For those about to rock... (%C, %R)
 ---------------------------------------------------------------
root@ArcherC6v2:/# </nowiki>
</WRAP>\\

==== OpenWrt bootlog ====
<WRAP bootlog>
<nowiki>U-Boot 1.1.4 (Jun 26 2018 - 19:41:08)

ap152 - Dragonfly 1.0

DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 375k for U-Boot at: 87fa0000
Reserving 8256k for malloc() at: 87790000
Reserving 44 Bytes for Board Info at: 8778ffd4
Reserving 36 Bytes for Global Data at: 8778ffb0
Reserving 128k for boot params() at: 8776ffb0
Stack Pointer at: 8776ff98
Now running in RAM - U-Boot at: 87fa0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200 
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x60c02100
Hit any key to stop autoboot:  1  0 
## Booting image at 9f030000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.162
   Created:      2020-01-06  16:47:09 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1595721 Bytes =  1.5 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9f030040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.162 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10860-a3ffeb413b)) #0 Mon Jan 6 16:47:09 2020
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link Archer C6 v2
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x804fd740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 123300K/131072K available (4027K kernel code, 156K rwdata, 532K rodata, 1228K init, 212K bss, 7772K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008220] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.074772] pid_max: default: 32768 minimum: 301
[    0.079799] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.086787] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.097700] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108095] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.114592] pinctrl core: initialized pinctrl subsystem
[    0.122156] NET: Registered protocol family 16
[    0.129374] PCI host bridge /ahb/apb/pcie-controller@18250000 ranges:
[    0.136217]  MEM 0x0000000012000000..0x0000000013ffffff
[    0.141719]   IO 0x0000000000000000..0x0000000000000000
[    0.161707] PCI host bridge to bus 0000:00
[    0.166036] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    0.173320] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.179183] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.186343] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.195089] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.205412] clocksource: Switched to clocksource MIPS
[    0.211621] NET: Registered protocol family 2
[    0.216990] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.224342] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.231093] TCP: Hash tables configured (established 1024 bind 1024)
[    0.237928] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.244091] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.250950] NET: Registered protocol family 1
[    0.258158] Crashlog allocated RAM at address 0x3f00000
[    0.264803] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.275885] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.282031] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.300796] io scheduler noop registered
[    0.304929] io scheduler deadline registered (default)
[    0.312083] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[    0.320349] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.329135] console [ttyS0] disabled
[    0.332934] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[    0.342067] console [ttyS0] enabled
[    0.342067] console [ttyS0] enabled
[    0.349633] bootconsole [early0] disabled
[    0.349633] bootconsole [early0] disabled
[    0.375310] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.380349] 5 fixed-partitions partitions found on MTD device spi0.0
[    0.386924] Creating 5 MTD partitions on "spi0.0":
[    0.391882] 0x000000000000-0x000000020000 : "u-boot"
[    0.397714] 0x000000020000-0x000000030000 : "mac"
[    0.403212] 0x000000030000-0x0000007d0000 : "firmware"
[    0.410985] 2 uimage-fw partitions found on MTD device firmware
[    0.417145] Creating 2 MTD partitions on "firmware":
[    0.422281] 0x000000000000-0x000000190000 : "kernel"
[    0.428077] 0x000000190000-0x0000007a0000 : "rootfs"
[    0.433787] mtd: device 4 (rootfs) set to be root filesystem
[    0.439717] 1 squashfs-split partitions found on MTD device rootfs
[    0.446127] 0x000000470000-0x0000007a0000 : "rootfs_data"
[    0.452342] 0x0000007d0000-0x0000007f0000 : "tplink"
[    0.458156] 0x0000007f0000-0x000000800000 : "art"
[    0.464618] libphy: Fixed MDIO Bus: probed
[    1.145773] libphy: ag71xx_mdio: probed
[    1.152729] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus.0
[    1.806887] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    1.818482] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[    1.827156] NET: Registered protocol family 10
[    1.836618] Segment Routing with IPv6
[    1.840488] NET: Registered protocol family 17
[    1.845117] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.858537] 8021q: 802.1Q VLAN Support v1.8
[    1.864257] hctosys: unable to open rtc device (rtc0)
[    1.874775] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.888784] Freeing unused kernel memory: 1228K
[    1.893458] This architecture does not have kernel memory protection.
[    2.531840] init: Console is alive
[    2.535609] init: - watchdog -
[    2.565428] random: fast init done
[    3.570525] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.609768] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.627899] init: - preinit -
[    4.434519] random: jshn: uninitialized urandom read (4 bytes read)
[    4.544833] random: jshn: uninitialized urandom read (4 bytes read)
[    4.718883] random: jshn: uninitialized urandom read (4 bytes read)
[    6.045853] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.051943] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[    6.090613] urandom_read: 4 callbacks suppressed
[    6.090620] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.076733] eth0: link up (1000Mbps/Full duplex)
[    7.081584] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.088392] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[    9.291048] jffs2: notice: (458) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[    9.308837] mount_root: switching to jffs2 overlay
[    9.335056] overlayfs: upper fs does not support tmpfile.
[    9.345746] urandom-seed: Seeding with /etc/urandom.seed
[    9.442587] eth0: link down
[    9.461963] procd: - early -
[    9.465029] procd: - watchdog -
[   10.083278] procd: - watchdog -
[   10.086837] procd: - ubus -
[   10.153879] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.190940] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.198778] procd: - init -
Please press Enter to activate this console.
[   10.735541] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.816606] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.842295] Loading modules backported from Linux version v4.19.85-0-gc63ee2939dc1
[   10.850162] Backport generated by backports.git v4.19.85-1-0-g8a8be258
[   10.859883] urngd: v1.0.0 started.
[   10.876611] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.888868] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   10.989147] xt_time: kernel timezone is -0000
[   11.089632] PPP generic driver version 2.4.2
[   11.104838] random: crng init done
[   11.109170] NET: Registered protocol family 24
[   11.139567] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x56.
[   11.149190] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   11.155327] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   11.347574] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
[   11.358487] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.541640] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[   11.553844] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-5.bin failed with error -2
[   11.565210] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.747364] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   11.757195] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-2.bin failed with error -2
[   11.768552] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.946529] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   11.956387] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/firmware-6.bin failed with error -2
[   11.967473] ath10k_pci 0000:00:00.0: Falling back to user helper
[   12.146098] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   12.737346] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[   12.746910] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   12.766906] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 a08ba414
[   13.101256] ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=20 from ath10k/QCA9888/hw2.0/board-2.bin
[   13.115263] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id 0:20 crc32 00e85542
[   15.165980] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   15.173719] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[   15.203790] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   15.215146] ath10k_pci 0000:00:00.0: wmi print 'free: 117888 iram: 22644 sram: 26276'
[   15.424747] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   15.610977] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[   15.656183] kmodloader: done loading kernel modules from /etc/modules.d/*
[   25.827000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   25.855733] br-lan: port 1(eth0.1) entered blocking state
[   25.861318] br-lan: port 1(eth0.1) entered disabled state
[   25.867194] device eth0.1 entered promiscuous mode
[   25.872149] device eth0 entered promiscuous mode
[   25.940411] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   26.013159] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   26.845631] eth0: link up (1000Mbps/Full duplex)
[   26.867421] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   26.900888] br-lan: port 1(eth0.1) entered blocking state
[   26.906521] br-lan: port 1(eth0.1) entered forwarding state
[   26.912538] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   27.036491] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 19.07.0, r10860-a3ffeb413b
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# </nowiki>
</WRAP>\\

===== Notes =====
//Space for additional notes, links to forum threads or other resources.//

  * ...

===== Tags =====
[[meta:tags|How to add tags]]
{{tag>ath79 8flash 128ram 5port GigabitEthernet 802.11ac 802.11abgn}}
ath79 8Flash 128ram 5port gigabitethernet 802.11ac 802.11abgn