TP-Link Archer C20i

Note: The TP-Link Archer C2 AC750 is similar to C20i, but has a Gigabit switch instead of the 100M switch in the C20i.

Flashing from the latest TP-Link firmware (Build 151014) via the web interface seems to brick the device. Download and flash an older OEM firmware first (Build 140709) before you continue.

If the stock firmware is not too recent (see above), OpenWrt can be flashed via web interface by using the OpenWrt -factory.bin images (see above).

If you happen to brick your device, it can be recovered via TFTP using a recovery image (more information is provided here).

TFTP recovery images for Archer C20i differ from the normal firmware images as they do not have the 512-byte long header at the beginning of the file. In order to create a recovery image, download a stock firmware image like this one and strip the header from the file:

dd if=archer_firwmare.bin of=ArcherC20iV1_tp_recovery.bin bs=512 skip=1

To flash the recovery, start a TFTP server from IP address 192.168.0.66 and serve the recovery image named ArcherC20iV1_tp_recovery.bin. Connect to your device to the LAN port, then press the WPS/Reset button and power it up. It will try to download the recovery image and flash it.

The following procedure allows you to upload a firmware image in case of emergency: 1) Hold the WPS button during startup. 2) After 10 seconds the router will start trying to download a file ArcherC20iV1_tp_recovery.bin via tftp from a server with the IP 192.168.0.66 for 10 more seconds.

Works via TFTP (see above)

Before installing OpenWrt snapshot versions, please take a look at the bug report system here https://bugs.openwrt.org/?string=archerc20i & latest git commits for C20i to rule out any reported bugs. Also keep in mind there is no LuCi/Web GUI included in snapshot images, but can be installed by following this infomation optional_next_steps.

USB works in openWrt since r46348 and LEDE (See git, 2015-07-14) https://git.lede-project.org/?p=source.git;a=commit;h=0ac2ef13f7a095eb0e397676fae642f59dad59e4

Architecture MIPS 24KEc V5.0
Vendor ?
bootloader U-Boot
System-On-Chip Mediatek MT7620A ver:2 eco:6
CPU/Speed 580 MHz
Flash-Chip Winbond 25q64fvsig
Flash size 8192 KB
RAM 64 MB
Wireless No1 MT7620A 2.4GHz
Wireless No2 MT7610E 5GHz (works in 19.07)
switch mt7620
USB Yes 1 x 2.0

Serial console is available on the J2 connector, 3.3v signals.

The square pad (pin 1) is Vcc and hence unused, pin 2 is Gnd and the remaining two pins are Rx and Tx. The picture below shows the serial port brought out to an external connector.

If running factory software then the username on the serial console is admin and the password is 1234

Please note that the LAN port numbering does not follow the internal switch numbering order (3/4/1/2 → 1/2/3/4).

Port Switch port
WAN 0
LAN 3 1
LAN 4 2
LAN 1 3
LAN 2 4
(not used) 5
CPU 6

Some simple WiFi file transfers using 2.4GHz N and WPA2 indicates practical speeds of about 70-100Mbit/s between Archer C20i and a MacBook Air located quite close to the router.

Flash is identified as an SPI connected 64 Mbit (8MB) Macronix MX25L6405D but the bootlog says “found mx25l6405d, expected en25q64” suggesting that different chips may be present in different hardware batches.

dev:    size   erasesize  name
mtd0: 00020000 00010000 "u-boot"
mtd1: 007a0000 00010000 "firmware"
mtd2: 00140000 00010000 "kernel"
mtd3: 00660000 00010000 "rootfs"
mtd4: 00430000 00010000 "rootfs_data"
mtd5: 00010000 00010000 "config"
mtd6: 00010000 00010000 "rom"
mtd7: 00010000 00010000 "romfile"
mtd8: 00010000 00010000 "radio"

The stock U-Boot identifies itself as: version 1.1.3 (Jun 23 2014 - 15:14:15) Ralink UBoot Version: 4.1.2.0

U-Boot is set up to autoboot without the normal delay prompt but t does accept some Mediatek / Ralink specific commands at that point. Reviewing the U-Boot source code suggests the following are supported but only option 4 has been tested (there are some other options but they appear to be wrapped in #if 0).

  • 4 - Enter Boot Command Line Interface
  • 7 - Load Boot Loader then write to Flash via Serial
  • 0 - Load Linux then write to Flash via Serial
  • 5 - Load Linux then write to Flash via USB Storage

This has been cleaned up a bit to fix some of the interspersed output from different parallel threads

U-Boot 1.1.3 (Jun 23 2014 - 15:14:15) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb0000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ------------------ Archer C20i v1.0.0 ------------------ spi_wait_nsec: 29 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D ============================================ Ralink UBoot Version: 4.1.2.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Jun 23 2014 Time:15:14:15 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes continue to starting system. 0 disableEthForward(1158):disable switch forward... 3: System Boot system code via Flash.(0xbc020000) do_bootm:argc=2, addr=0xbc020000 ## Booting image at bc020000 ... Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c150) ... ## Giving linux memsize in MB, 64 Starting kernel ... Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #57 Tue May 12 09:29:13 HKT 2015 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe CPU revision is: 00019650 (MIPS 24Kc) Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0001fb9f Readback ErrCtl register=0001fb9f Memory: 61368k/65536k available (2704k kernel code, 4168k reserved, 564k data, 164k init, 0k highmem) NR_IRQS:128 MTK/Ralink System Tick Counter init... cd:8031ff68, m:214748, s:32 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 4096 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 1ab11d RALINK_GPIOMODE = 18b11d PPLL_CFG1=0xe3c000 MT7620 PPLL lock PPLL_DRV =0x80080504 start PCIe register access RALINK_PCI_PCICFG_ADDR = 1000f0 *************** MT7620 PCIe RC mode ************* bio: create slab <bio-0> at 0 pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] pci 0000:00:00.0: bridge window [mem pref disabled] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 20200000 res[1]->end = 2020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20000000 res[0]->end = 200fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20100000 res[0]->end = 201fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink external timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 RT3xxx EHCI/OHCI init. squashfs: version 4.0 (2009/01/31) Phillip Lougher fuse init (API version 7.15) msgmni has been set to 119 io scheduler noop registered io scheduler deadline registered (default) Ralink gpio driver initialized Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A loop: module loaded deice id : c2 20 17 c2 20 (2017c220) MX25L6405D(c2 2017c220) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536 Creating 7 MTD partitions on "raspi": 0x000000000000-0x000000020000 : "boot" 0x000000020000-0x000000160000 : "kernel" 0x000000160000-0x0000007c0000 : "rootfs" mtd: partition "rootfs" set to be root filesystem 0x0000007c0000-0x0000007d0000 : "config" 0x0000007d0000-0x0000007e0000 : "romfile" 0x0000007e0000-0x0000007f0000 : "rom" 0x0000007f0000-0x000000800000 : "radio" Register flash device:flash0 PPP generic driver version 2.4.2 NET: Registered protocol family 24 Mirror/redirect action on u32 classifier Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (2874 buckets, 11496 max) ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 164k freed starting pid 173, tty '': '/etc/init.d/rcS' rdm_major = 253 SCSI subsystem initialized spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6 Read MAC from flash(0x7DF100) fffffff4-fffffff2-6d-ffffff9e-ffffffdf-ffffffe5 SMACCR1 -- : 0x0000f4f2 SMACCR0 -- : 0x6d9edfe5 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6 Read MAC from flash(0x7DF100) fffffff4-fffffff2-6d-ffffff9e-ffffffdf-ffffffe5 SMACCR1 -- : 0x0000f4f2 SMACCR0 -- : 0x6d9edfe5 PROC INIT OK! usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. tp_domain init ok L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 Please press Enter to activate this console. [ util_execSystem ] 135: ipt_init cmd is "/var/tmp/dconf/rc.router" [ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml spiflash_ioctl_read, Read from 0x007c0000 length 0x10000, ret 0, retlen 0x10000 spiflash_ioctl_read, Read from 0x007c0000 length 0x40, ret 0, retlen 0x40 [ dm_loadCfg ] 2254: software version is not match, in config, version = 271585328 [ dm_readFile ] 2042: can not open xml file /var/tmp/pc/default_config.xml!, about to open file /etc/default_config.xml [ parseConfigNode ] 522: Meet unrecognized object node "PhDDNSCfg", skip the node [ parseConfigNode ] 527: Meet unrecognized parameter node "PhDDNSCfg", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "SnmpCfg", skip the node spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6 [ parseConfigNode ] 522: Meet unrecognized object node "ACL", skip the node spiflash_ioctl_read, Read from 0x007df200 length 0x4, ret 0, retlen 0x4 spiflash_ioctl_read, Read from 0x00020000 length 0x1d0, ret 0, retlen 0x1d0 spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6 [ parseConfigNode ] 527: Meet unrecognized parameter node "ACL", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "X_TP_WANUSB3gLinkConfig", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "QueueManagement", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "X_TP_IPTV", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "VoiceService", skip the node [ parseConfigNode ] 527: Meet unrecognized parameter node "VoiceService", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "X_TP_SpeedDialCfg", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "X_TP_MultiIspDialPlan", skip the node [ parseConfigNode ] 522: Meet unrecognized object node "X_TP_CallLogCfg", skip the node sendto: No such file or directory pid 251 send 2001 error [ util_execSystem ] 135: oal_startDynDns cmd is "dyndns /var/tmp/dconf/dyndns.conf" [ oal_sys_getOldTZInfo ] 333: Open TZ file error! [ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ" [ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ" [ util_execSystem ] 135: oal_startNoipDns cmd is "noipdns /var/tmp/dconf/noipdns.conf" [ util_execSystem ] 135: oal_startCmxDns cmd is "cmxdns /var/tmp/dconf/cmxdns.conf" ioctl: No such device [ util_execSystem ] 135: oal_br_addBridge cmd is "brctl addbr br0;brctl setfd br0 0;brctl stp br0 off" spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6 [ util_execSystem ] 135: oal_ipt_addLanRules cmd is "iptables -t filter -A INPUT -i br+ -j ACCEPT" [ util_execSystem ] 135: oal_intf_setIntf cmd is "ifconfig br0 192.168.0.1 netmask 255.255.255.0 up" [ util_execSystem ] 135: oal_util_setProcLanAddr cmd is "echo "br0 16820416," > /pRaeth v3.0 (roc/nWorkqueueet) /conntrac phy_tx_ring = 0x030bf000, tx_ring = 0xa30bf000 phy_rx_ring0 = 0x030c0000, rx_ring0 = 0xa30c0000 SMACCR1 -- : 0x0000f4f2 SMACCR0 -- : 0x6d9edfe5 t_CDMA_CSG_CFG = 81000000 Lo calAddr" GDMA1_FWD_CFG = 20710000 [ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0 up" [ util_execSystem ] 135: rsl_initLanEthIntfObj cmd is "vconfig add eth0 3" [ util_execSystem ] 135: rsl_initLanEthIntfObj cmd is "ifconfig eth0.3 up" [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 eth0.3" device eth0.3 entered promiscuous mode device eth0 entered promiscuous mode br0: port 1(eth0.3) entering forwarding state br0: port 1(eth0.3) entering forwarding state [ util_execSystem ] 135: rsl_initLanEthIntfObj cmd is "vconfig add eth0 2" [ util_execSystem ] 135: rsl_initLanEthIntfObj cmd is "ifconfig eth0.2 up" [ util_execSystem ] 135: rsl_initIPv6CfgObj cmd is "echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6" [ util_execSystem ] 135: oal_eth_setIGMPSnoopParam cmd is "brctl setbrsnooping br0 1" [ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "cp /etc/SingleSKU_FCC.dat /var/Wireless/RT2860AP/SingleSKU.dat" [ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "iwpriv ra0 set CountryRegion=0" ra0 no private ioctls. [ util_execSystem ] 135: oal_wlan_ra_loadDriver cmd is "insmod /lib/modules/kmdir/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko" ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready rt2860v2_ap: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint === pAd = c0970000, size = 968080 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.1.6_edcca_monitor_20131227 [ util_execSystem ] 135: oal_wlan_ra_initWlan cmd is "ifconfig ra0 up" RX DESC a321b000 size = 4096 RTMP_TimerListAdd: add timer obj c0a1d930! RTMP_TimerListAdd: add timer obj c09d5940! RTMP_TimerListAdd: add timer obj c09d8194! RTMP_TimerListAdd: add timer obj c09d8254! RTMP_TimerListAdd: add timer obj c09d8314! RTMP_TimerListAdd: add timer obj c09d83d4! RTMP_TimerListAdd: add timer obj c09d8494! RTMP_TimerListAdd: add timer obj c09d8554! RTMP_TimerListAdd: add timer obj c09d8614! RTMP_TimerListAdd: add timer obj c09d86d4! RTMP_TimerListAdd: add timer obj c09d8794! RTMP_TimerListAdd: add timer obj c09d8854! RTMP_TimerListAdd: add timer obj c09d8914! RTMP_TimerListAdd: add timer obj c09d89d4! RTMP_TimerListAdd: add timer obj c09d8a94! RTMP_TimerListAdd: add timer obj c09d8b54! RTMP_TimerListAdd: add timer obj c09d8c14! RTMP_TimerListAdd: add timer obj c09d8cd4! RTMP_TimerListAdd: add timer obj c09d5914! RTMP_TimerListAdd: add timer obj c09d8168! RTMP_TimerListAdd: add timer obj c09d8228! RTMP_TimerListAdd: add timer obj c09d82e8! RTMP_TimerListAdd: add timer obj c09d83a8! RTMP_TimerListAdd: add timer obj c09d8468! RTMP_TimerListAdd: add timer obj c09d8528! RTMP_TimerListAdd: add timer obj c09d85e8! RTMP_TimerListAdd: add timer obj c09d86a8! RTMP_TimerListAdd: add timer obj c09d8768! RTMP_TimerListAdd: add timer obj c09d8828! RTMP_TimerListAdd: add timer obj c09d88e8! RTMP_TimerListAdd: add timer obj c09d89a8! RTMP_TimerListAdd: add timer obj c09d8a68! RTMP_TimerListAdd: add timer obj c09d8b28! RTMP_TimerListAdd: add timer obj c09d8be8! RTMP_TimerListAdd: add timer obj c09d8ca8! RTMP_TimerListAdd: add timer obj c09d58e8! RTMP_TimerListAdd: add timer obj c09d81c0! RTMP_TimerListAdd: add timer obj c09d8280! RTMP_TimerListAdd: add timer obj c09d8340! RTMP_TimerListAdd: add timer obj c09d8400! RTMP_TimerListAdd: add timer obj c09d84c0! RTMP_TimerListAdd: add timer obj c09d8580! RTMP_TimerListAdd: add timer obj c09d8640! RTMP_TimerListAdd: add timer obj c09d8700! RTMP_TimerListAdd: add timer obj c09d87c0! RTMP_TimerListAdd: add timer obj c09d8880! RTMP_TimerListAdd: add timer obj c09d8940! RTMP_TimerListAdd: add timer obj c09d8a00! RTMP_TimerListAdd: add timer obj c09d8ac0! RTMP_TimerListAdd: add timer obj c09d8b80! RTMP_TimerListAdd: add timer obj c09d8c40! RTMP_TimerListAdd: add timer obj c09d8d00! RTMP_TimerListAdd: add timer obj c097c9b0! RTMP_TimerListAdd: add timer obj c097c5a4! RTMP_TimerListAdd: add timer obj c097c980! RTMP_TimerListAdd: add timer obj c097cd28! RTMP_TimerListAdd: add timer obj c097ca78! RTMP_TimerListAdd: add timer obj c097caa8! RTMP_TimerListAdd: add timer obj c097cc68! RTMP_TimerListAdd: add timer obj c097cc98! RTMP_TimerListAdd: add timer obj c097fbe8! RTMP_TimerListAdd: add timer obj c097f7dc! RTMP_TimerListAdd: add timer obj c097fbb8! RTMP_TimerListAdd: add timer obj c097ff60! RTMP_TimerListAdd: add timer obj c097fcb0! RTMP_TimerListAdd: add timer obj c097fce0! RTMP_TimerListAdd: add timer obj c097fea0! RTMP_TimerListAdd: add timer obj c097fed0! RTMP_TimerListAdd: add timer obj c0982e20! RTMP_TimerListAdd: add timer obj c0982a14! RTMP_TimerListAdd: add timer obj c0982df0! RTMP_TimerListAdd: add timer obj c0983198! RTMP_TimerListAdd: add timer obj c0982ee8! RTMP_TimerListAdd: add timer obj c0982f18! RTMP_TimerListAdd: add timer obj c09830d8! RTMP_TimerListAdd: add timer obj c0983108! RTMP_TimerListAdd: add timer obj c0986058! RTMP_TimerListAdd: add timer obj c0985c4c! RTMP_TimerListAdd: add timer obj c0986028! RTMP_TimerListAdd: add timer obj c09863d0! RTMP_TimerListAdd: add timer obj c0986120! RTMP_TimerListAdd: add timer obj c0986150! RTMP_TimerListAdd: add timer obj c0986310! RTMP_TimerListAdd: add timer obj c0986340! RTMP_TimerListAdd: add timer obj c0989290! RTMP_TimerListAdd: add timer obj c0988e84! RTMP_TimerListAdd: add timer obj c0989260! RTMP_TimerListAdd: add timer obj c0989608! RTMP_TimerListAdd: add timer obj c0989358! RTMP_TimerListAdd: add timer obj c0989388! RTMP_TimerListAdd: add timer obj c0989548! RTMP_TimerListAdd: add timer obj c0989578! RTMP_TimerListAdd: add timer obj c098c4c8! RTMP_TimerListAdd: add timer obj c098c0bc! RTMP_TimerListAdd: add timer obj c098c498! RTMP_TimerListAdd: add timer obj c098c840! RTMP_TimerListAdd: add timer obj c098c590! RTMP_TimerListAdd: add timer obj c098c5c0! RTMP_TimerListAdd: add timer obj c098c780! RTMP_TimerListAdd: add timer obj c098c7b0! RTMP_TimerListAdd: add timer obj c098f700! RTMP_TimerListAdd: add timer obj c098f2f4! RTMP_TimerListAdd: add timer obj c098f6d0! RTMP_TimerListAdd: add timer obj c098fa78! RTMP_TimerListAdd: add timer obj c098f7c8! RTMP_TimerListAdd: add timer obj c098f7f8! RTMP_TimerListAdd: add timer obj c098f9b8! RTMP_TimerListAdd: add timer obj c098f9e8! RTMP_TimerListAdd: add timer obj c0992938! RTMP_TimerListAdd: add timer obj c099252c! RTMP_TimerListAdd: add timer obj c0992908! RTMP_TimerListAdd: add timer obj c0992cb0! RTMP_TimerListAdd: add timer obj c0992a00! RTMP_TimerListAdd: add timer obj c0992a30! RTMP_TimerListAdd: add timer obj c0992bf0! RTMP_TimerListAdd: add timer obj c0992c20! RTMP_TimerListAdd: add timer obj c09d7d4c! RTMP_TimerListAdd: add timer obj c09d7940! RTMP_TimerListAdd: add timer obj c09d7d1c! RTMP_TimerListAdd: add timer obj c09d80c4! RTMP_TimerListAdd: add timer obj c09d7e14! RTMP_TimerListAdd: add timer obj c09d7e44! RTMP_TimerListAdd: add timer obj c09d7d7c! RTMP_TimerListAdd: add timer obj c09d7dac! RTMP_TimerListAdd: add timer obj c09d7ddc! RTMP_TimerListAdd: add timer obj c09f429c! RTMP_TimerListAdd: add timer obj c09f43b8! RTMP_TimerListAdd: add timer obj c09f42c8! RTMP_TimerListAdd: add timer obj c09d9e84! RTMP_TimerListAdd: add timer obj c0979e70! RTMP_TimerListAdd: add timer obj c097d0a8! RTMP_TimerListAdd: add timer obj c09802e0! RTMP_TimerListAdd: add timer obj c0983518! RTMP_TimerListAdd: add timer obj c0986750! RTMP_TimerListAdd: add timer obj c0989988! RTMP_TimerListAdd: add timer obj c098cbc0! RTMP_TimerListAdd: add timer obj c098fdf8! RTMP_TimerListAdd: add timer obj c09d9b94! !!! use RTMP_RBUS_SUPPORT: AP_PROFILE_PATH_RBUS is /var/Wireless/RT2860AP/RT2860AP.dat APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 exec! spiflash_ioctl_read, Read from 0x007f0000 length 0x200, ret 0, retlen 0x200 eeFlashId = 0x7620! E2PROM: D0 target power=0xff1c E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 RTMP_TimerListAdd: add timer obj c0979a68! AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = 0, D2 = 8, CalCode = 19 !!! RT6352_Temperature_Init : BBPR49 = 0x0 RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff6 Current Temperature from BBP_R49=0xfffffffb RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127 RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128 *** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -25 -12 - 0 - 12 28 127 127 127 127 127, offset=-10, tuning=0 RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -35 -22 - -10 - 2 18 117 117 117 117 117, offset=-10, tuning=0 mp_temperature=0xfffffffc, step = +0 E2PROM: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -35 -22 - -10 - 2 18 117 117 117 117 117, offset=-10, tuning=0 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= f, phase=3b) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 0, phase=3d) TX IQ Calibration Done! bAutoTxAgcG = 0 MCS Set = ff ff 00 00 01 SYNC - BBP R4 to 20MHz.l RTMP_TimerListAdd: add timer obj c09da19c! The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4 Main bssid = f4:f2:6d:xx:xx:xx <==== rt28xx_init, Status=0 0x1300 = 00064300 [ util_execSystem ] 135: oal_wlan_ra_initWlan cmd is "echo 1 > /proc/tplink/led_wlan_24G" [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 ra0" device ra0 entered promiscuous mode br0: port 2(ra0) entering forwarding state br0: port 2(ra0) entering forwarding state [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 apcli0" device apcli0 entered promiscuous mode [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 apcli0" brctl: bridge br0: Device or resource busy device ra1 entered promiscuous mode [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 ra1" spiflash_ioctl_read, Read from 0x007f0000 length 0x2, ret 0, retlen 0x2 [ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "wlNetlinkTool &" [ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "killall -q wscd" [ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "wscd -i ra0 -m 1 -w /var/tmp/wsc_upnp/ &" [ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "cp /etc/SingleSKU_5G_FCC.dat /var/Wireless/RT2860AP/SingleSKU_5G.dat" WLAN-Start wlNetlinkTool Waiting for Wireless Events from interfaces... swWlanChkAhbErr: netlink to do [ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "iwpriv rai0 set CountryRegionABand=0" rai0 no private ioctls. [ util_execSystem ] 135: oal_wlan_ra_loadDriver cmd is "insmod /lib/modules/kmdir/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko" wscd: SSDP UDP PORT = 1900 === pAd = c0f02000, size = 1378776 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 device_id =0x7650 eeFlashId = 0x7610! spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200 ==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002 MACVersion = 0x76502000 [ util_execSystem ] 135: oal_wlan_ra_initWlan cmd is "ifconfig rai0 up" MAC[Ver:Rev=0x76502000 : 0x76100002] load fw spent 12ms RX DESC a2079000 size = 4096 RX1 DESC a207a000 size = 4096 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! 1. Phy Mode = 49 2. Phy Mode = 49 ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1 ext_pa_current_setting = 1 3. Phy Mode = 49 AntCfgInit: primary/secondary ant 0/1 ChipStructAssign(): RALINK6590 hook ! bAutoTxAgcG = 0 MCS Set = ff 00 00 00 01 MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) Main bssid = f4:f2:6d:xx:xx:xx <==== rt28xx_init, Status=0 MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 52, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 52, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 56, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 56, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 60, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 60, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 64, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 64, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 149, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 149, param = 0x901, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 153, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 153, param = 0x901, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 157, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 157, param = 0x901, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 161, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 161, param = 0x901, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_Calibration - Channel = 165, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 165, param = 0x901, bSave = 0, CalibrationMode = 255 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42 MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28 APStartUp(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2) MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0 FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255 0x1300 = 00064300 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! [ util_execSystem ] 135: oal_wlan_ra_initWlan cmd is "echo 1 > /proc/tplink/led_wlan_5G" [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 rai0" device rai0 entered promiscuous mode br0: port 5(rai0) entering forwarding state br0: port 5(rai0) entering forwarding state [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 apclii0" device apclii0 entered promiscuous mode [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 apclii0" device rai1 entered promiscuous mode brctl: bridge br0: Device or resource busy spiflash_ioctl_read, Read from 0x007f8000 length 0x2, ret 0, retlen 0x2 [ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 rai1" wlNetlinkTool is already there. [ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "killall -q wscd_5G" [ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "wscd_5G -i rai0 -m 1 -w /var/tmp/wsc_upnp_5G/ &" wscd: SSDP UDP PORT = 1900 sendto: No such file or directory pid 251 send 2030 error sendto: No such file or directory pid 251 send 2004 error [ util_execSystem ] 135: oal_startDhcps cmd is "dhcpd /var/tmp/dconf/udhcpd.conf" [ util_execSystem ] 135: oal_lan6_startDhcp6s cmd is "dhcp6s -c /var/tmp/dconf/dhcp6s_br0.conf -P /var/run/dhcp6s_br0.pid br0 &" [ util_execSystem ] 135: oal_lan6_startRadvd cmd is "radvd -C /var/tmp/dconf/radvd_br0.conf -p /var/run/radvd_br0.pid &" mldProxy# file: src/mld_ifinfo.c;line: 102; error = No such file or directory mldProxy# Err: get LLA failed [ util_execSystem ] 135: oal_br_delIntfFromBridge cmd is "brctl delif br0 eth0.2" brctl: bridge br0: Invalid argument [ util_execSystem ] 135: oal_intf_setIfMac cmd is "ifconfig eth0.2 down" [ util_execSystem ] 135: oal_intf_setIfMac cmd is "ifconfig eth0.2 hw ether F4:F2:6D:XX:XX:XX up" [ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0.2 up" iptables: Bad rule (does a matching rule exist in that chain?). radvd starting [Jan 01 00:00:14] radvd: no linklocal address configured for br0 [Jan 01 00:00:14] radvd: error parsing or activating the config file: /var/tmp/dconf/radvd_br0.conf [ util_execSystem ] 135: prepareDropbear cmd is "dropbearkey -t rsa -f /var/tmp/dropbear/dropbear_rsa_host_key" Will output 1024 bit rsa secret key to '/var/tmp/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... [ util_execSystem ] 135: prepareDropbear cmd is "dropbearkey -t dss -f /var/tmp/dropbear/dropbear_dss_host_key" Will output 1024 bit dss secret key to '/var/tmp/dropbear/dropbear_dss_host_key' Generating key, this may take a while... [ util_execSystem ] 135: oal_rip_updateConfig cmd is "rm -f /var/tmp/dconf/zebra.conf" [ util_execSystem ] 135: oal_rip_updateConfig cmd is "rm -f /var/tmp/dconf/ripd.conf" [ util_execSystem ] 135: removeAllRIPIpTableRule cmd is "iptables -L INPUT -v --line-numbers > /var/iptable" [ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid. [ util_execSystem ] 135: controlRipProcess cmd is "zebra -d -f /var/tmp/dconf/zebra.conf" [ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid. [ util_execSystem ] 135: oal_ipt_fwDdos cmd is "iptables -D FORWARD -j FIREWALL_DDOS " iptables: No chain/target/match by that name. [ util_execSystem ] 135: oal_ipt_setDDoSRules cmd is "iptables -F FIREWALL_DDOS" [ util_execSystem ] 135: ddos_clearAll cmd is "rm -f /var/tmp/dosHost" [ util_execSystem ] 135: oal_initFirewallObj cmd is "ebtables -N FIREWALL" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -F" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -X" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -P INPUT ACCEPT" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -P FORWARD DROP" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -P OUTPUT ACCEPT" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -N FIREWALL" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -N FWRULE" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -i lo -p ALL -j ACCEPT -m comment --comment "loop back"" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -i br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -o br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT" [ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -j FIREWALL" [ util_execSystem ] 135: oal_fw6_setFwEnabeld cmd is "ip6tables -D FIREWALL -j ACCEPT" ip6tables: Bad rule (does a matching rule exist in that chain?). [ util_execSystem ] 135: oal_fw6_setFwEnabeld cmd is "ip6tables -F FIREWALL" [ util_execSystem ] 135: oal_fw6_setFwEnabeld cmd is "ip6tables -A FIREWALL -j ACCEPT" [ rsl_setStorageServiceObj ] 1024: mountFlag is 3,We start usb server [ util_execSystem ] 135: oal_killDlnaMediaSeverProcess cmd is "killall ushare" killall: ushare: no process killed [ util_execSystem ] 135: prepareDropbear cmd is "dropbear -p 22 -r /var/tmp/dropbear/dropbear_rsa_host_key -d /var/tmp/dropbear/dropbear_dss_host_key -A /var/tmp/dropbear/dropbearpwd" [ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ" [ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ" uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server. Benjamin Zores (C) 2005-2007, for GeeXboX Team. See http://ushare.geexbox.org/ for updates. [ util_execSystem ] 135: oal_ipt_setWanPort cmd is "iptables -t filter -D INPUT -p tcp --dport 21 -j ACCEPT" iptables: Bad rule (does a matching rule exist in that chain?). [ util_execSystem ] 135: oal_ipt_setWanPort cmd is "iptables -t nat -D PREROUTING -p tcp --dport 21 -j ACCEPT" iptables: Bad rule (does a matching rule exist in that chain?). [ util_execSystem ] 135: oal_startPrintSrv cmd is "insmod /lib/modules/GPL_NetUSB.ko" kcg 333 :GPL NetUSB up! [ util_execSystem ] 135: oal_startPrintSrv cmd is "insmod /lib/modules/NetUSB.ko" kc 90 : run_telnetDBGDServer start kc 227 : init_DebugD end INFO17DE: NetUSB 1.02.65, 00020624 : Apr 20 2015 18:02:18 INFO17E0: 7437: Archer C20i v1 :Archer C20i v1 INFO17E1: AUTH ISOC INFO17E2: filterAudio usbcore: registered new interface driver KC NetUSB General Driver INFO0145: init proc : PAGE_SIZE 4096 INFO16D2: infomap c114cd44 INFO16D5: sleep to wait br0 to wake up [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_coINFO15A7: tcpConnector() started... : br0 nntrack_ftp.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_ftp.ko" [ util_execSystem ] 135: oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 500 -j DROP" iptables: Bad rule (does a matching rule exist in that chain?). [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_pptp.ko" [ util_execSystem ] 135: oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH -p tcp --dport 1723 -j DROP" iptables: Bad rule (does a matching rule exist in that chain?). [ util_execSystem ] 135: oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 1701 -j DROP" iptables: Bad rule (does a matching rule exist in that chain?). [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_tftp.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_tftp.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_h323.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_h323.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_sip.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_sip.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_rtsp.ko" [ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_rtsp.ko" nf_nat_rtsp v0.6.21 loading [ util_execSystem ] 135: oal_wan_HWNat_enable cmd is "insmod /lib/modules/kmdir/kernel/net/nat/hw_nat/hw_nat.ko" Ralink HW NAT Module Enabled INFO155A: Bind to br0


[ 0.000000] Linux version 3.18.11 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45556) ) #1 Tue May 19 00:54:24 CEST 2015 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is TP-Link Archer C20i [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 803282b0, node_mem_map 81009000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0004b3e0 [ 0.000000] Readback ErrCtl register=0004b3e0 [ 0.000000] Memory: 61164K/65536K available (2661K kernel code, 134K rwdata, 532K rodata, 184K init, 190K bss, 4372K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.050000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.080000] NET: Registered protocol family 16 [ 0.090000] rt2880-pinmux pinctrl: try to register 73 pins ... [ 0.090000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux [ 0.090000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux [ 0.090000] pinctrl core: add 6 pinmux maps [ 0.090000] rt2880-pinmux pinctrl: found group selector 0 for i2c [ 0.090000] rt2880-pinmux pinctrl: found group selector 1 for uartf [ 0.090000] rt2880-pinmux pinctrl: found group selector 6 for rgmii1 [ 0.090000] rt2880-pinmux pinctrl: found group selector 10 for rgmii2 [ 0.090000] rt2880-pinmux pinctrl: found group selector 11 for wled [ 0.090000] rt2880-pinmux pinctrl: found group selector 9 for nd_sd [ 0.090000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 7 (io7) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 8 (io8) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 9 (io9) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 10 (io10) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 12 (io12) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 24 (io24) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 25 (io25) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 26 (io26) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 27 (io27) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 28 (io28) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 29 (io29) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 30 (io30) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 31 (io31) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 32 (io32) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 33 (io33) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 34 (io34) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 35 (io35) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 60 (io60) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 61 (io61) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 62 (io62) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 63 (io63) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 64 (io64) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 65 (io65) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 66 (io66) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 67 (io67) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 68 (io68) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 69 (io69) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 70 (io70) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 71 (io71) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 72 (io72) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 45 (io45) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 46 (io46) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 47 (io47) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 48 (io48) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 49 (io49) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 50 (io50) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 51 (io51) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 52 (io52) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 53 (io53) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 54 (io54) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 55 (io55) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 56 (io56) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 57 (io57) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 58 (io58) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: request pin 59 (io59) for pinctrl [ 0.090000] rt2880-pinmux pinctrl: failed to lookup the sleep state [ 0.090000] pinctrl core: add 1 pinmux maps [ 0.090000] rt2880-pinmux pinctrl: found group selector 8 for pcie [ 0.090000] rt2880-pinmux pinctrl: request pin 36 (io36) for 10140000.pcie [ 0.340000] PCI host bridge /pcie@10140000 ranges: [ 0.350000] MEM 0x0000000020000000..0x000000002fffffff [ 0.350000] IO 0x0000000010160000..0x000000001016ffff [ 0.360000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.360000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.370000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.370000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.380000] PCI host bridge to bus 0000:00 [ 0.380000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.390000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 0.390000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.400000] pci 0000:00:00.0: [1814:0802] type 01 class 0x060400 [ 0.400000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 0.400000] pci 0000:00:00.0: reg 0x14: [mem 0x20200000-0x2020ffff] [ 0.400000] pci 0000:00:00.0: supports D1 [ 0.400000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.400000] pci 0000:01:00.0: [14c3:7650] type 00 class 0x028000 [ 0.400000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 0.400000] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.400000] pci 0000:01:00.1: [14c3:8650] type 00 class 0x0d1100 [ 0.400000] pci 0000:01:00.1: reg 0x10: [mem 0x00000000-0x000fffff] [ 0.400000] pci 0000:01:00.1: supports D1 [ 0.400000] pci 0000:01:00.1: PME# supported from D0 D1 D3hot D3cold [ 0.400000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.400000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.400000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.400000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.410000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 0.410000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.420000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 0.420000] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.430000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.430000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 0.440000] pci 0000:00:00.0: card - bus=0x0, slot = 0x0 irq=0 [ 0.440000] pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 0.450000] pci 0000:01:00.1: card - bus=0x1, slot = 0x0 irq=4 [ 0.450000] Switched to clocksource systick [ 0.460000] NET: Registered protocol family 2 [ 0.460000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.460000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.470000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.480000] TCP: reno registered [ 0.480000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.480000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.490000] NET: Registered protocol family 1 [ 0.490000] PCI: CLS 80 bytes, default 32 [ 0.500000] rt-timer 10000100.timer: maximum frequency is 2441Hz [ 0.500000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT [ 0.500000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.520000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.520000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.530000] msgmni has been set to 119 [ 0.540000] io scheduler noop registered [ 0.540000] io scheduler deadline registered (default) [ 0.550000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[147] [ 0.550000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[161] [ 0.560000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.570000] serial8250 serial8250: no of_node; not parsing pinctrl DT [ 0.570000] pinctrl core: add 1 pinmux maps [ 0.570000] rt2880-pinmux pinctrl: found group selector 3 for uartlite [ 0.570000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite [ 0.570000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite [ 0.570000] console [ttyS0] disabled [ 0.570000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A [ 0.580000] console [ttyS0] enabled [ 0.590000] bootconsole [early0] disabled [ 0.600000] pinctrl core: add 1 pinmux maps [ 0.600000] rt2880-pinmux pinctrl: found group selector 2 for spi [ 0.600000] rt2880-pinmux pinctrl: request pin 3 (io3) for 10000b00.spi [ 0.600000] rt2880-pinmux pinctrl: request pin 4 (io4) for 10000b00.spi [ 0.600000] rt2880-pinmux pinctrl: request pin 5 (io5) for 10000b00.spi [ 0.600000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi [ 0.620000] m25p80 spi32766.0: found s25fl064k, expected en25q64 [ 0.620000] m25p80 spi32766.0: s25fl064k (8192 Kbytes) [ 0.630000] 6 ofpart partitions found on MTD device spi32766.0 [ 0.640000] Creating 6 MTD partitions on "spi32766.0": [ 0.640000] 0x000000000000-0x000000020000 : "u-boot" [ 0.650000] 0x000000020000-0x0000007c0000 : "firmware" [ 0.750000] 2 tplink-fw partitions found on MTD device firmware [ 0.750000] 0x000000020000-0x000000160000 : "kernel" [ 0.760000] 0x000000160000-0x0000007c0000 : "rootfs" [ 0.760000] mtd: device 3 (rootfs) set to be root filesystem [ 0.770000] 1 squashfs-split partitions found on MTD device rootfs [ 0.780000] 0x000000390000-0x0000007c0000 : "rootfs_data" [ 0.780000] 0x0000007c0000-0x0000007d0000 : "config" [ 0.790000] 0x0000007d0000-0x0000007e0000 : "rom" [ 0.790000] 0x0000007e0000-0x0000007f0000 : "romfile" [ 0.800000] 0x0000007f0000-0x000000800000 : "radio" [ 0.810000] pinctrl core: add 1 pinmux maps [ 0.810000] rt2880-pinmux pinctrl: found group selector 12 for ephy [ 0.810000] rt2880-pinmux pinctrl: request pin 40 (io40) for 10100000.ethernet [ 0.810000] rt2880-pinmux pinctrl: request pin 41 (io41) for 10100000.ethernet [ 0.810000] rt2880-pinmux pinctrl: request pin 42 (io42) for 10100000.ethernet [ 0.810000] rt2880-pinmux pinctrl: request pin 43 (io43) for 10100000.ethernet [ 0.810000] rt2880-pinmux pinctrl: request pin 44 (io44) for 10100000.ethernet [ 0.810000] gsw: setting port4 to ephy mode [ 0.810000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex) [ 0.810000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link up (100Mbps/Full duplex) [ 0.840000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.840000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.850000] rt2880_wdt 10000120.watchdog: Initialized [ 0.860000] TCP: cubic registered [ 0.860000] NET: Registered protocol family 17 [ 0.860000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.880000] Bridge firewalling registered [ 0.880000] 8021q: 802.1Q VLAN Support v1.8 [ 0.900000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.910000] Freeing unused kernel memory: 184K (80342000 - 80370000) [ 3.510000] init: failed to symlink /tmp -> /var [ 3.520000] init: Console is alive [ 3.520000] init: - watchdog - [ 5.900000] usbcore: registered new interface driver usbfs [ 5.910000] usbcore: registered new interface driver hub [ 5.910000] usbcore: registered new device driver usb [ 5.920000] gpio-keys-polled gpio-keys-polled: missing platform data [ 5.930000] gpio-keys-polled: probe of gpio-keys-polled failed with error -22 [ 5.940000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.940000] ehci-platform: EHCI generic platform driver [ 5.950000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.960000] ohci-platform: OHCI generic platform driver [ 6.550000] init: - preinit - [ 7.120000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 7.170000] random: mktemp urandom read with 8 bits of entropy available [ 10.860000] jffs2: notice: (320) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found. [ 10.880000] mount_root: switching to jffs2 overlay [ 10.920000] procd: - early - [ 10.920000] procd: - watchdog - [ 11.900000] procd: - ubus - [ 13.080000] procd: - init - [ 13.820000] NET: Registered protocol family 10 [ 13.830000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 13.850000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 13.860000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 13.870000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 13.880000] nf_conntrack version 0.5.0 (958 buckets, 3832 max) [ 13.930000] xt_time: kernel timezone is -0000 [ 13.960000] cfg80211: Calling CRDA to update world regulatory domain [ 13.990000] cfg80211: World regulatory domain updated: [ 13.990000] cfg80211: DFS Master region: unset [ 14.000000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 14.010000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 14.010000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 14.020000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 14.030000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 14.040000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 14.050000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 14.060000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 14.060000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 14.060000] PPP generic driver version 2.4.2 [ 14.060000] NET: Registered protocol family 24 [ 14.060000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected [ 14.060000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 14.060000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 21.740000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 21.760000] device eth0.1 entered promiscuous mode [ 21.760000] device eth0 entered promiscuous mode [ 21.780000] br-lan: port 1(eth0.1) entered forwarding state [ 21.780000] br-lan: port 1(eth0.1) entered forwarding state [ 23.780000] br-lan: port 1(eth0.1) entered forwarding state


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1