TOTOLINK X5000R

Totolink X5000R

Warning!!

The manufacturer have started to use a new flash chip, Zbit Semiconductor part #ZB25VQ128ASIG.

This isn't currently supported by OpenWRT, there's however an error report open at https://github.com/openwrt/openwrt/issues/12306

OpenWRT images supporting the new chip can be found at https://github.com/ThranduilII/openwrt/files/11399622/Openwrt-22.03.5-X5000R-Zbit-support.zip.

Until the issue's resolved, you CANNOT use any official OpenWRT image, only the one from the link above.

Please check your flash chip before flashing OpenWRT.

You will see the following message on the console if you have an unsupported chip

[    4.325094] spi-nor spi0.0: unrecognized JEDEC id bytes: 5e 40 18 5e 40 18
[    4.331987] spi-nor: probe of spi0.0 failed with error -2

An image of the chip can be found at https://forum.openwrt.org/t/got-stuck-on-system-running-in-recovery-initramfs-mode-totolink-x5000r/160442/115

Edit September 2023: There is even another Flash chip, which works with the regular OpenWRT builds. The part is labeled “XMC PPF39300_08” (or similar, hard to read)

  1. Download the OpenWrt sysupgrade image as shown above
  2. Flash using OEM web UI

Source

  1. Poweroff / unplug power adapter from the router
  2. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
  3. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
  4. Plug the LAN cable from your computer into LAN 1 port
  5. Confirm that you can connect to the router by ping 192.168.1.1 from command prompt / terminal
  6. If you get reply from 192.168.1.1, then open web browser, and type in the address column : 192.168.1.1
  7. You will get the X5000R firmware update page, then choose the factory-firmware file from previously downloaded file
  8. Wait untill the router finish flashing (the router will reboot by itself) : Blue led dan green LAN led will blinking
  9. Revert the computer ethernet ip to automatic
  10. Open in web browser : itotolink.net or 192.168.0.1
  11. Finish, you should get Totolink web gui config page
Architecture MIPS 1004Kc
Vendor Mediatek
Bootloader U-Boot
System-On-Chip Mediatek MT7621A
CPU/Speed 880 MHz dual core
Flash chip Eon EN25QH128 or XMC 25QH128CHIQ
Flash size/type 16 MiB/NOR
RAM chip Nanya NT5CC128M16IP
RAM size/type 256 MiB/DDR3
Wireless MT 7915 dual radio 802.11ax
Ethernet 1000 Mbit/s w/ vlan support
Serial Pads on board

Product image Device opened

Top of the PCB, tape over connectors removed Bottom od the PCB

There are 4 screws and a lot of plastic clips. No screws behind stickers or anything.

port.serial The serial port of the X5000R can be accessed using the TTL 3.3V pins behind the power plug connector. A voltage level converter (such as a MAX3232 TTL-RS232 dongle) is required.
The communication settings are: 115200, 8N1

TFTP

From u-boot menu option 2, the sysupgrade Openwrt firmware can be downloaded. OEM firmware can be reloaded as well.
Default TFTP server address : 192.168.1.2 (other server IP can be input)
Default FW file name : test.bin (other file name can be input)

[ 0.000000] Linux version 3.4.113 (gitlab-runner@Gitlab-CD) (gcc version 4.4.7 (GCC) ) #1 SMP Mon Nov 2 15:38:33 CST 2020 [ 0.000000] [ 0.000000] MediaTek SoC: MT7621A, RevID: 0103, RAM: DDR3, XTAL: 40MHz [ 0.000000] CPU/OCP/SYS frequency: 880/293/220 MHz [ 0.000000] MT7621:ECO(0103) has PCIe reset BUG!!! [ 0.000000] MT7621: PCIe host/device reset [ 0.000000] prom memory:256MB [ 0.000000] CPU revision is: 0001992f (MIPS 1004Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00010000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s6016 r8192 d14464 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock4 rootfstype=squashfs [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00050945 [ 0.000000] Readback ErrCtl register=00050945 [ 0.000000] Memory: 255236k/262144k available (3335k kernel code, 6908k reserved, 848k data, 228k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:72 [ 0.000000] MIPS GIC RevID: 3.0 [ 0.000000] Setting up vectored interrupts [ 0.000000] console [ttyS0] enabled [ 0.004000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) [ 0.040000] pid_max: default: 32768 minimum: 301 [ 0.044000] Mount-cache hash table entries: 512 [ 0.048000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.056000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.060000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.068000] CPU revision is: 0001992f (MIPS 1004Kc) [ 0.104000] Synchronize counters for CPU 1: done. [ 0.112000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.116000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.124000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.132000] CPU revision is: 0001992f (MIPS 1004Kc) [ 0.168000] Synchronize counters for CPU 2: done. [ 0.176000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.180000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.188000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.196000] CPU revision is: 0001992f (MIPS 1004Kc) [ 0.228000] Synchronize counters for CPU 3: done. [ 0.236000] Brought up 4 CPUs [ 0.240000] NET: Registered protocol family 16 [ 0.252000] MT7621:PCIe device GPIO reset [ 0.652000] MT7621 PCIe PHY initialize [ 1.800000] PCIE2 no card, disable it(RST&CLK) [ 1.804000] PCIE0:link up [ 1.804000] PCIE1:link up [ 1.808000] PCIE2:link down [ 1.808000] mt762x-pcie:register pci controller [ 1.820000] bio: create slab <bio-0> at 0 [ 1.824000] SCSI subsystem initialized [ 1.828000] PCI host bridge to bus 0000:00 [ 1.832000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.836000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.840000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.844000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.848000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) [ 1.852000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) [ 1.856000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref] [ 1.860000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x603fffff pref] [ 1.864000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 1.868000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 1.872000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref] [ 1.876000] pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref] [ 1.880000] pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref] [ 1.884000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 1.888000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref] [ 1.892000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit pref] [ 1.896000] pci 0000:02:00.0: BAR 2: assigned [mem 0x60300000-0x60303fff 64bit pref] [ 1.900000] pci 0000:02:00.0: BAR 4: assigned [mem 0x60304000-0x60304fff 64bit pref] [ 1.904000] pci 0000:00:01.0: PCI bridge to [bus 02-02] [ 1.908000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x603fffff pref] [ 1.912000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) [ 1.916000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006) [ 1.920000] PCI Bus 1 slot 0 mapping to IRQ12. [ 1.924000] PCI Bus 2 slot 1 mapping to IRQ32. [ 1.928000] Switching to clocksource MIPS [ 1.932000] PandoraBox SPLICE initialized. rcv 8fde0000 (sz:1560) kvec 8fd90000 (sz:520) per 4 core [ 1.940000] NET: Registered protocol family 2 [ 1.964000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 1.972000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.976000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.984000] TCP: Hash tables configured (established 8192 bind 8192) [ 1.992000] TCP: reno registered [ 1.992000] UDP hash table entries: 128 (order: 0, 4096 bytes) [ 2.000000] NET: Registered protocol family 1 [ 2.092000] 4 CPUs re-calibrate udelay (lpj = 1167360) [ 2.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.108000] msgmni has been set to 498 [ 2.116000] io scheduler noop registered (default) [ 2.120000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 2.128000] serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A [ 2.132000] Ralink GPIO driver initialized. Number of GPIO: 64, GPIO mode: 000405AC [ 2.144000] MediaTek SPI flash driver, SPI clock: 44MHz [ 2.148000] SPI flash chip: EN25QH128 (1c 70181c30) (16384 Kbytes) [ 2.156000] Generic partitions detected at 0x50000! [ 2.160000] Creating 9 MTD partitions on "raspi": [ 2.164000] 0x000000000000-0x000000030000 : "Bootloader" [ 2.172000] 0x000000030000-0x000000040000 : "Config" [ 2.176000] 0x000000040000-0x000000050000 : "Factory" [ 2.184000] 0x000000050000-0x0000001d4cb0 : "Kernel" [ 2.188000] 0x0000001d4cb0-0x000000f70000 : "RootFS" [ 2.196000] mtd: device 4 (RootFS) set to be root filesystem [ 2.200000] 0x000000f70000-0x000000f80000 : "Userdata" [ 2.204000] 0x000000f80000-0x000001000000 : "Storage" [ 2.212000] 0x000000050000-0x000000f70000 : "Firmware_Stub" [ 2.220000] 0x000000000000-0x000001000000 : "fullflash" [ 2.224000] tun: Universal TUN/TAP device driver, 1.6 [ 2.228000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 2.236000] EEPROM:Read from [Factory] offset 0xe000,length 0x6. [ 2.248000] EEPROM:Read from [Factory] offset 0xe006,length 0x6. [ 2.256000] Ralink APSoC Ethernet Driver v3.2.4 (raeth) [ 2.260000] raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536 [ 2.268000] raeth: NAPI support, weight 32 [ 2.272000] PPP generic driver version 2.4.2 [ 2.276000] PPP MPPE Compression module registered [ 2.280000] NET: Registered protocol family 24 [ 2.284000] PPTP driver version 0.8.5 [ 2.288000] u32 classifier [ 2.292000] nf_conntrack version 0.5.0 (32768 buckets, 32768 max) [ 2.300000] xt_time: kernel timezone is -0000 [ 2.304000] IPv4 over IPv4 tunneling driver [ 2.308000] gre: GRE over IPv4 demultiplexor driver [ 2.316000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.320000] TCP: cubic registered [ 2.324000] NET: Registered protocol family 10 [ 2.328000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.336000] IPv6 over IPv4 tunneling driver [ 2.340000] NET: Registered protocol family 17 [ 2.344000] NET: Registered protocol family 15 [ 2.348000] L2TP core driver, V2.0 [ 2.352000] PPPoL2TP kernel driver, V2.0 [ 2.356000] 8021q: 802.1Q VLAN Support v1.8 [ 2.360000] EEPROM:Read from [Config] offset 0x1000,length 0xf000. [ 2.384000] CaryStudio NVRAM, v0.08. Available space: 61440. Integrity: OK [ 2.396000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.404000] Freeing unused kernel memory: 228k freed [ 2.716000] Algorithmics/MIPS FPU Emulator v1.5 validate subfs: [ 6.268000] register mt_drv [ 6.272000] <--mt7916_hif_init() [ 6.276000] Rx[0] Ring: total 24576 bytes allocated [ 6.288000] Rx[1] Ring: total 16384 bytes allocated [ 6.292000] <-- pci_alloc_tx_rx_ring_mem, Status=0 [ 6.340000] [ 6.340000] [ 6.340000] === pAd = c1601000, size = 12014848 === [ 6.340000] [ 6.352000] <-- RTMPAllocAdapterBlock, Status=0 [ 6.356000] PCI CSRBaseAddress =0xc1500000, csr_addr=0xc1500000! [ 6.360000] RTMPInitPCIeDevice():device_id=0x7915 [ 6.368000] mt7915_init()--> [ 6.368000] Use 1st iPAiLNA default bin. [ 6.372000] <--mt7915_init() [ 6.408000] Rx[0] Ring: total 24576 bytes allocated [ 6.412000] Rx[1] Ring: total 24576 bytes allocated [ 6.424000] Rx[2] Ring: total 8192 bytes allocated [ 6.436000] Rx[3] Ring: total 16384 bytes allocated [ 6.444000] Rx[4] Ring: total 8192 bytes allocated [ 6.448000] <-- pci_alloc_tx_rx_ring_mem, Status=0 [ 6.488000] Netfilter messages via NETLINK v0.30. [ 6.528000] ip_set: protocol 6 Password for 'root' changed [ 6.936000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled [ 6.944000] raeth: HW VLAN RX offload enabled [ 6.948000] raeth: HW VLAN TX offload enabled [ 6.952000] raeth: HW Scatter/Gather TX offload enabled [ 6.956000] raeth: HW TCP segmentation offload (TSO) enabled [ 6.968000] mtk_esw - hw bridge: W|LLLL [ 6.976000] mtk_esw - set broadcast storm control rate as: 10 mbps [ 6.992000] ra0: ===> main_virtual_if_open [ 6.996000] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 7.004000] load l1profile succeed! [ 7.008000] mt_service_open: wlan service opens successfully! [ 7.112000] [multi_profile_merge_5g_only] DBDC_MODE=1 [ 7.128000] multi-profile merge success, en:1,pf1_num:2,pf2_num:2,total:4 [ 7.136000] Open file "/etc/Wireless/RT2860/DBDC_card0.dat" to store DBDC cfg! (21) [ 7.144000] Write file "/etc/Wireless/RT2860/DBDC_card0.dat" success (size=5956)! [ 7.152000] BssidNum=4 [ 7.156000] Pf2MbssIdxMap: [ 7.156000] 0 1 2 3 [ 7.160000] MacAddress2 = 00:00:00:00:00:00 [ 7.164000] E2pAccessMode=2 [ 7.168000] SSID[0]=TOTOLINK_X5000R, EdcaIdx=0 [ 7.172000] SSID[1]=TOTOLINK_X5000R_GUEST, EdcaIdx=0 [ 7.180000] SSID[2]=TOTOLINK_X5000R, EdcaIdx=0 [ 7.184000] SSID[3]=TOTOLINK_X5000R_5G_GUEST, EdcaIdx=0 [ 7.188000] RTMPSetProfileParameters(): DBDC Mode=1, eDBDC_mode = 1 [ 7.196000] cfg_mode=16 [ 7.200000] cfg_mode=16 [ 7.200000] cfg_mode=16 [ 7.204000] wmode_band_equal(): Band Equal! [ 7.208000] cfg_mode=16 [ 7.212000] cfg_mode=16 [ 7.212000] cfg_mode=16 [ 7.216000] cfg_mode=17 [ 7.216000] cfg_mode=17 [ 7.220000] cfg_mode=17 [ 7.224000] cfg_mode=17 [ 7.224000] auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 7.232000] auto_ch_select_set_cfg(): BandIdx1, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 7.244000] Index0 Channel=6 [ 7.244000] Index1 Channel=36 [ 7.248000] BandSteering=1 [ 7.252000] BndStrgBssIdx=1;0;1;0 [ 7.256000] [TxPower] BAND0: 100, BAND1: 100 [ 7.260000] [PowerUpenable] BAND0: 0, BAND1: 100 [ 7.268000] [SKUenable] BAND0: 0, BAND1: 0 [ 7.272000] [PERCENTAGEenable] BAND0: 1, BAND1: 1 [ 7.280000] profile: FragThreshold[0]=2346 [ 7.284000] profile: FragThreshold[1]=2346 [ 7.288000] profile: FragThreshold[2]=2346 [ 7.292000] profile: FragThreshold[3]=2346 [ 7.296000] APEdca0 [ 7.300000] Valid=1 [ 7.300000] APAifsn[0]=3 [ 7.304000] APAifsn[1]=7 [ 7.308000] APAifsn[2]=1 [ 7.308000] APAifsn[3]=1 [ 7.312000] APEdca1 [ 7.316000] Valid=1 [ 7.316000] APAifsn[0]=3 [ 7.320000] APAifsn[1]=7 [ 7.320000] APAifsn[2]=1 [ 7.324000] APAifsn[3]=1 [ 7.328000] APEdca2 [ 7.328000] APEdca3 [ 7.336000] BSSAifsn[0]=3 [ 7.340000] BSSAifsn[1]=7 [ 7.340000] BSSAifsn[2]=2 [ 7.344000] BSSAifsn[3]=2 [ 7.348000] BSSAifsn[0]=3 [ 7.348000] BSSAifsn[1]=7 [ 7.352000] BSSAifsn[2]=2 [ 7.356000] BSSAifsn[3]=2 [ 7.356000] BSSAifsn[0]=3 [ 7.360000] BSSAifsn[1]=7 [ 7.364000] BSSAifsn[2]=2 [ 7.364000] BSSAifsn[3]=2 [ 7.368000] BSSAifsn[0]=3 [ 7.372000] BSSAifsn[1]=7 [ 7.372000] BSSAifsn[2]=2 [ 7.376000] BSSAifsn[3]=2 [ 7.380000] UAPSDCapable[0]=1 [ 7.380000] UAPSDCapable[1]=1 [ 7.384000] default ApCliUAPSDCapable[0]=1 [ 7.388000] default ApCliUAPSDCapable[1]=1 [ 7.396000] DfsZeroWait Support=0/0 [ 7.400000] DfsZeroWaitCacTime=255/255 [ 7.404000] read_itxbf: ITxBfEn = 1 [ 7.408000] read_itxbf: BSSID[0] [ 7.412000] read_itxbf: MBSS[0] ITxBfEn = 1 [ 7.416000] read_itxbf: ITxBfEn = 1 [ 7.420000] read_itxbf: BSSID[1] [ 7.420000] read_itxbf: MBSS[1] ITxBfEn = 1 [ 7.424000] read_itxbf: ITxBfEn = 1 [ 7.428000] read_itxbf: BSSID[2] [ 7.432000] read_itxbf: MBSS[2] ITxBfEn = 1 [ 7.436000] read_itxbf: ITxBfEn = 1 [ 7.440000] read_itxbf: BSSID[3] [ 7.444000] read_itxbf: MBSS[3] ITxBfEn = 1 [ 7.448000] read_itxbf: Common.ITxBfEn = 1 [ 7.452000] read_etxbf: ETxBfEnCond = 1 [ 7.456000] read_etxbf: BSSID[0] [ 7.460000] read_etxbf: MBSS[0] ETxBfEnCond = 1 [ 7.464000] read_etxbf: ETxBfEnCond = 1 [ 7.468000] read_etxbf: BSSID[1] [ 7.472000] read_etxbf: MBSS[1] ETxBfEnCond = 1 [ 7.476000] read_etxbf: ETxBfEnCond = 1 [ 7.480000] read_etxbf: BSSID[2] [ 7.484000] read_etxbf: MBSS[2] ETxBfEnCond = 1 [ 7.488000] read_etxbf: ETxBfEnCond = 1 [ 7.492000] read_etxbf: BSSID[3] [ 7.492000] read_etxbf: MBSS[3] ETxBfEnCond = 1 [ 7.500000] MBSS[0] MuOfdmaDlEnable = 1 [ 7.504000] MBSS[1] MuOfdmaDlEnable = 1 [ 7.508000] MBSS[2] MuOfdmaDlEnable = 1 [ 7.512000] MBSS[3] MuOfdmaDlEnable = 1 [ 7.516000] MBSS[0] MuOfdmaUlEnable = 1 [ 7.520000] MBSS[1] MuOfdmaUlEnable = 1 [ 7.524000] MBSS[2] MuOfdmaUlEnable = 1 [ 7.528000] MBSS[3] MuOfdmaUlEnable = 1 [ 7.532000] MBSS[0] MuMimoDlEnable = 1 [ 7.536000] MBSS[1] MuMimoDlEnable = 1 [ 7.540000] MBSS[2] MuMimoDlEnable = 1 [ 7.544000] MBSS[3] MuMimoDlEnable = 1 [ 7.548000] MBSS[0] MuMimoUlEnable = 1 [ 7.552000] MBSS[1] MuMimoUlEnable = 1 [ 7.556000] MBSS[2] MuMimoUlEnable = 1 [ 7.560000] MBSS[3] MuMimoUlEnable = 1 [ 7.564000] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [ 7.596000] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [ 7.604000] [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0 [ 7.608000] [PMF]Set_PMFMFPC_Proc:: apidx=2, Desired MFPC=0 [ 7.616000] [PMF]Set_PMFMFPC_Proc:: apidx=3, Desired MFPC=0 [ 7.620000] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [ 7.624000] [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0 [ 7.632000] [PMF]Set_PMFMFPR_Proc:: apidx=2, Desired MFPR=0 [ 7.636000] [PMF]Set_PMFMFPR_Proc:: apidx=3, Desired MFPR=0 [ 7.644000] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [ 7.648000] [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0 [ 7.656000] [PMF]Set_PMFSHA256_Proc:: apidx=2, Desired PMFSHA256=0 [ 7.660000] [PMF]Set_PMFSHA256_Proc:: apidx=3, Desired PMFSHA256=0 [ 7.668000] ApCliEntry[0].Enable=0 [ 7.672000] ApCliEntry[1].Enable=0 [ 7.680000] ApCliUAPSDCapable[0]=0 [ 7.680000] ApCliUAPSDCapable[1]=0 [ 7.692000] HT_BAWinSize: wdev[0]: (TX=64, RX=64) [ 7.696000] HT_BAWinSize: wdev[1]: (TX=64, RX=64) [ 7.700000] HT_BAWinSize: wdev[2]: (TX=64, RX=64) [ 7.704000] HT_BAWinSize: wdev[3]: (TX=64, RX=64) [ 7.712000] HT: WDEV[0] Ext Channel = ABOVE [ 7.716000] HT: WDEV[1] Ext Channel = ABOVE [ 7.720000] HT: WDEV[2] Ext Channel = ABOVE [ 7.724000] HT: WDEV[3] Ext Channel = ABOVE [ 7.728000] HT: greenap_cap = 0 [ 7.732000] ChipI=7915, Value=0, pcie_aspm in profile=0 [ 7.736000] ChipID=7915, TWTSupport in profile=1 [ 7.808000] WtcSetMaxStaNum: MaxStaNum:250, BssidNum:4, WdsNum:0, MSTANum:1, MaxNumChipRept:32, MinMcastWcid:283 [ 7.820000] Top Init Done! [ 7.820000] Use dev_alloc_skb [ 7.824000] token_tx_two_queues_init(): ct sw token(0) number = 2048 [ 7.832000] token_tx_two_queues_init(): token que(0) inited done!id_head/tail=0/2048 [ 7.840000] token_tx_two_queues_init(): 8ca63e04,8ca63e04 [ 7.844000] token_tx_two_queues_init(): ct sw token(1) number = 6144 [ 7.852000] token_tx_two_queues_init(): token que(1) inited done!id_head/tail=0/6144 [ 7.860000] token_tx_two_queues_init(): 8ca63eac,8ca63eac [ 7.872000] TxRing[0]: attr:0, total 2048 entry initialized [ 7.880000] TxRing[1]: attr:0, total 2048 entry initialized [ 7.888000] TxRing[2]: attr:0, total 2048 entry initialized [ 7.896000] RX[0] DESC af778000 size = 24576 [ 7.904000] RX[1] DESC af774000 size = 16384 [ 7.912000] RX[2] DESC ac090000 size = 24576 [ 7.920000] RX[3] DESC ac098000 size = 24576 [ 7.924000] RX[4] DESC ac9fa000 size = 8192 [ 7.928000] RX[5] DESC ac1d8000 size = 16384 [ 7.932000] RX[6] DESC abffa000 size = 8192 [ 7.940000] -->TX_RING_0[0xd9330]: Attr:0, Base=0xd160000, Cnt=2048! [ 7.944000] -->TX_RING_1[0xd7300]: Attr:0, Base=0xc048000, Cnt=2048! [ 7.952000] -->TX_RING_2[0xd7310]: Attr:0, Base=0xc080000, Cnt=2048! [ 7.956000] -->TX_RING_3[0xd5400]: Attr:3, Base=0xf71a000, Cnt=128! [ 7.964000] -->TX_RING_4[0xd5410]: Attr:2, Base=0xf691000, Cnt=256! [ 7.972000] -->TX_RING_5[0xd5440]: Attr:1, Base=0xf6d1000, Cnt=256! [ 7.976000] -->RX_RING0[0xd8510]: Base=0xf778000, Cnt=1536 [ 7.984000] -->RX_RING1[0xd9520]: Base=0xf774000, Cnt=1024 [ 7.988000] -->RX_RING2[0xd4500]: Base=0xc090000, Cnt=1536 [ 7.992000] -->RX_RING3[0xd4510]: Base=0xc098000, Cnt=10 [ 8.000000] -->RX_RING4[0xd5500]: Base=0xc9fa000, Cnt=512 [ 8.004000] -->RX_RING5[0xd7410]: Base=0xc1d8000, Cnt=1024 [ 8.008000] -->RX_RING6[0xd5520]: Base=0xbffa000, Cnt=512 [ 8.016000] Hif Init Done! [ 8.020000] pci_driver_own_by_port: success to clear p=0 fw own, from(1): 1 is interrupt mode, 2 is polling mode. [ 8.032000] pci_driver_own_by_port: success to clear p=1 fw own, from(1): 1 is interrupt mode, 2 is polling mode. [ 8.040000] fw_prepare():using E2 ROM patch [ 8.048000] fw_prepare():using E2 RAM [ 8.048000] Parsing patch header [ 8.052000] Built date: 20201008102431a [ 8.056000] [ 8.060000] Platform: ALPS [ 8.060000] HW/SW version: 0x8a108a10 [ 8.064000] Patch version: 0xffffffff [ 8.068000] Section num: 0x2, subsys: 0x4 [ 8.072000] Section 0: type = 0x30002, offset = 0xe0, size = 0xfc90 [ 8.080000] Target address: 0x200000, length: 0xfc90 [ 8.084000] Section 1: type = 0x30002, offset = 0xfd70, size = 0x13720 [ 8.092000] Target address: 0xe000f000, length: 0x13720 [ 8.096000] Patch SEM Status = 2 [ 8.100000] patch is not ready && get semaphore success [ 8.104000] Start address = 0x200000, DL length = 64656, Data mode = 0x80000000 [ 8.112000] EventGenericEventHandler: CMD Success [ 8.120000] MtCmdAddressLenReq:(ret = 0) [ 8.124000] Start address = 0xe000f000, DL length = 79648, Data mode = 0x80000000 [ 8.132000] EventGenericEventHandler: CMD Success [ 8.136000] MtCmdAddressLenReq:(ret = 0) [ 8.140000] MtCmdPatchFinishReq [ 8.148000] EventGenericEventHandler: CMD Success [ 8.152000] Patch SEM Status = 3 [ 8.156000] release patch semaphore [ 8.160000] WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0 [ 8.168000] Parsing CPU 0 fw tailer [ 8.172000] Chip ID: 0x0b [ 8.172000] Eco version: 0x01 [ 8.176000] Region number: 0x07 [ 8.180000] Format version: 0x02 [ 8.184000] Format flag: 0x01 [ 8.184000] Ram version: ____000000 [ 8.188000] Built date: 20201008102505 [ 8.192000] Common crc: 0x22dd69bf [ 8.196000] Parsing tailer region 0 [ 8.200000] Decomp crc: 0x0 [ 8.204000] Decomp size: 0x0 [ 8.208000] Decomp block size: 0x0 [ 8.208000] Target address: 0x21fc00 [ 8.212000] Download size: 110592 [ 8.216000] Feature set: 0x20 [ 8.220000] Parsing tailer region 1 [ 8.224000] Decomp crc: 0x0 [ 8.228000] Decomp size: 0x0 [ 8.228000] Decomp block size: 0x0 [ 8.232000] Target address: 0x31dc00 [ 8.236000] Download size: 205824 [ 8.240000] Feature set: 0x00 [ 8.244000] Parsing tailer region 2 [ 8.248000] Decomp crc: 0x0 [ 8.248000] Decomp size: 0x0 [ 8.252000] Decomp block size: 0x0 [ 8.256000] Target address: 0x417400 [ 8.260000] Download size: 31744 [ 8.264000] Feature set: 0x00 [ 8.264000] Parsing tailer region 3 [ 8.268000] Decomp crc: 0x0 [ 8.272000] Decomp size: 0x0 [ 8.276000] Decomp block size: 0x0 [ 8.280000] Target address: 0xe0022800 [ 8.284000] Download size: 395776 [ 8.284000] Feature set: 0x00 [ 8.288000] Parsing tailer region 4 [ 8.292000] Decomp crc: 0x0 [ 8.296000] Decomp size: 0x0 [ 8.296000] Decomp block size: 0x0 [ 8.300000] Target address: 0xe0083200 [ 8.304000] Download size: 347648 [ 8.308000] Feature set: 0x00 [ 8.312000] Parsing tailer region 5 [ 8.316000] Decomp crc: 0x0 [ 8.316000] Decomp size: 0x0 [ 8.320000] Decomp block size: 0x0 [ 8.324000] Target address: 0x23ac00 [ 8.328000] Download size: 87040 [ 8.332000] Feature set: 0x00 [ 8.336000] Parsing tailer region 6 [ 8.336000] Decomp crc: 0x0 [ 8.340000] Decomp size: 0x0 [ 8.344000] Decomp block size: 0x0 [ 8.348000] Target address: 0x400000 [ 8.352000] Download size: 81920 [ 8.356000] Feature set: 0x00 [ 8.356000] Release info: header tag = 0, total length = 72 [ 8.364000] tag 1, padding length = 1, tag length = 67 [ 8.368000] payload: t-neptune-main-mt7915-1953-MT7915_WIFI_RAM_REBB_1953-20201008102202 [ 8.376000] Start address = 0x21fc00, DL length = 110592, Data mode = 0x80000000 [ 8.384000] EventGenericEventHandler: CMD Success [ 8.388000] MtCmdAddressLenReq:(ret = 0) [ 8.396000] Start address = 0x31dc00, DL length = 205824, Data mode = 0x80000000 [ 8.404000] EventGenericEventHandler: CMD Success [ 8.408000] MtCmdAddressLenReq:(ret = 0) [ 8.416000] Start address = 0x417400, DL length = 31744, Data mode = 0x80000000 [ 8.424000] EventGenericEventHandler: CMD Success [ 8.428000] MtCmdAddressLenReq:(ret = 0) [ 8.432000] Start address = 0xe0022800, DL length = 395776, Data mode = 0x80000000 [ 8.440000] EventGenericEventHandler: CMD Success [ 8.444000] MtCmdAddressLenReq:(ret = 0) [ 8.456000] Start address = 0xe0083200, DL length = 347648, Data mode = 0x80000000 [ 8.464000] EventGenericEventHandler: CMD Success [ 8.468000] MtCmdAddressLenReq:(ret = 0) [ 8.476000] Start address = 0x23ac00, DL length = 87040, Data mode = 0x80000000 [ 8.484000] EventGenericEventHandler: CMD Success [ 8.488000] MtCmdAddressLenReq:(ret = 0) [ 8.496000] Start address = 0x400000, DL length = 81920, Data mode = 0x80000000 [ 8.504000] EventGenericEventHandler: CMD Success [ 8.508000] MtCmdAddressLenReq:(ret = 0) [ 8.512000] MtCmdFwStartReq: override = 0x1, address = 0x21fc00 [ 8.520000] EventGenericEventHandler: CMD Success [ 8.524000] Parsing CPU 1 fw tailer [ 8.528000] Chip ID: 0x00 [ 8.532000] Eco version: 0x01 [ 8.532000] Region number: 0x03 [ 8.536000] Format version: 0x02 [ 8.540000] Format flag: 0x01 [ 8.544000] Ram version: DEV_000000 [ 8.548000] Built date: 20201008102524 [ 8.552000] Common crc: 0x62f20c6a [ 8.556000] Parsing tailer region 0 [ 8.556000] Decomp crc: 0x0 [ 8.560000] Decomp size: 0x0 [ 8.564000] Decomp block size: 0x0 [ 8.568000] Target address: 0x10200000 [ 8.572000] Download size: 88512 [ 8.576000] Feature set: 0x00 [ 8.576000] Parsing tailer region 1 [ 8.580000] Decomp crc: 0x0 [ 8.584000] Decomp size: 0x0 [ 8.588000] Decomp block size: 0x0 [ 8.592000] Target address: 0x10300000 [ 8.592000] Download size: 19392 [ 8.596000] Feature set: 0x00 [ 8.600000] Parsing tailer region 2 [ 8.604000] Decomp crc: 0x0 [ 8.608000] Decomp size: 0x0 [ 8.608000] Decomp block size: 0x0 [ 8.612000] Target address: 0xe0000000 [ 8.616000] Download size: 8768 [ 8.620000] Feature set: 0x00 [ 8.624000] Release info: header tag = 0, total length = 0 [ 8.628000] Start address = 0x10200000, DL length = 88512, Data mode = 0x80000010 [ 8.636000] EventGenericEventHandler: CMD Success [ 8.644000] MtCmdAddressLenReq:(ret = 0) [ 8.648000] Start address = 0x10300000, DL length = 19392, Data mode = 0x80000010 [ 8.656000] EventGenericEventHandler: CMD Success [ 8.660000] MtCmdAddressLenReq:(ret = 0) [ 8.664000] Start address = 0xe0000000, DL length = 8768, Data mode = 0x80000010 [ 8.672000] EventGenericEventHandler: CMD Success [ 8.680000] MtCmdAddressLenReq:(ret = 0) [ 8.684000] MtCmdFwStartReq: override = 0x4, address = 0x0 [ 8.788000] EventGenericEventHandler: CMD Success [ 8.792000] MCU Init Done! [ 8.796000] efuse_probe: efuse = 10000012 [ 8.800000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 [ 8.804000] RtmpEepromGetDefault::e2p_dafault=1 [ 8.812000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 [ 8.816000] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] [ 8.824000] rtmp_nv_init(): EEPROM Size[4096] [ 8.828000] EEPROM:Read from [Factory] offset 0x0,length 0x1000. [ 8.836000] [EEPROMImage - PreCalImageInfo - PreCalImage - TxDPDImage] [ 8.836000] [0x8f683000 - 0x8f683e00 - 0x8f683e10 - 0x8f690220] [ 8.848000] validFlashEepromID(): eeFlashId=7915, pAd->ChipID=7915 [ 8.856000] [d-die version:1] [ 8.892000] [a-die version:2] [ 9.024000] [ 9.028000] NICReadEEPROMParameters: EEPROM 0x62 0 [ 9.628000] mtk_esw: Link Status Changed - Port WAN Link Up [ 14.288000] Country Region from e2p = 0 [ 14.292000] antenna_default_reset() todo [ 14.296000] antenna_default_reset() value = 0x5292, TxPath = 2, RxPath = 2 [ 14.300000] RTMPReadTxPwrPerRate(458): Don't Support this now! [ 14.308000] rc_radio_init(): DBDC MODE=1, ConcurrentBand=2 [ 14.312000] rc_radio_init(): radio_ctrl=8c0316d0,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf [ 14.320000] rc_radio_init(): radio_ctrl=8c031a28,Band=1,rfcap=3,channel=1,PhyMode=2 extCha=0xf [ 14.332000] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 [ 14.336000] ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 [ 14.340000] AntCfgInit(2744): Not support for HIF_MT yet! [ 14.348000] mt7915_check_RF_lock_down: RFlockDown Enable: 0 [ 14.352000] MtReadPwrLimitTable: sku table idx: 0 [ 14.352000] mt7915_check_RF_lock_down: RFlockDown Enable: 0 [ 14.372000] MtReadPwrLimitTable: sku table idx: 0 [ 14.372000] EEPROM Init Done! [ 14.388000] mac_init()--> [ 14.388000] init_mac_cr()--> [ 14.392000] <--mac_init() [ 14.400000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 14.408000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 14.416000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 14.420000] MAC Init Done! [ 14.424000] BBPInit():BBP Initialization..... [ 14.428000] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 [ 14.436000] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 [ 14.448000] BBPInit() todo [ 14.448000] PHY Init Done! [ 14.464000] tx_pwr_comp_init():NotSupportYet! [ 14.468000] Set_SCSDefaultEnable(): BandIdx=0, SCSEnable=1 [ 14.476000] Set_SCSDefaultEnable(): BandIdx=1, SCSEnable=1 [ 14.480000] MtCmdSetMacTxRx:(ret = 0) [ 14.484000] MtCmdSetMacTxRx:(ret = 0) [ 14.488000] ap_ftkd> Initialize FT KDP Module... [ 14.492000] Main bssid = 00:00:00:00:00:00 [ 14.496000] SetMuruPlatformTypeProc: param.ucPlatformType = 1 [ 14.504000] muru_cfg_dlul_limits:(Ret = 1 [ 14.508000] muru_cfg_dlul_limits:(Ret = 1 [ 14.512000] MtCmdSetMacTxRx:(ret = 0) [ 14.516000] MtCmdSetMacTxRx:(ret = 0) [ 14.520000] <==== mt_wifi_init, Status=0 [ 14.524000] CmdHeraStbcPriorityCtrl: u1BandIdx=0, u1Operation=1, u1StbcPriority=0 [ 14.532000] CmdHeraStbcPriorityCtrl: u1BandIdx=1, u1Operation=1, u1StbcPriority=0 [ 14.540000] Register MBSSID IF 1 (ra1) [ 14.544000] Register MBSSID IF 2 (rax0) [ 14.552000] Register MBSSID IF 3 (rax1) [ 14.556000] MSTA_Init (2) ---> ApCli [ 14.560000] Register MSTA IF (apcli0) , pAd->MSTANum = 1 [ 14.568000] Caller: SetCommonHT+0xf0/0x1e8 [mt_7915] [ 14.572000] [ 14.572000] phy_mode=78, ch=6, wdev_type=2 [ 14.580000] ht_cap: ht_cap->HtCapInfo, [ 14.584000] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 14.592000] ht_cap: ht_cap->HtCapParm, [ 14.592000] mdpu_density=0, ampdu_factor=3 [ 14.600000] Register MSTA IF (apclix0) , pAd->MSTANum = 2 [ 14.604000] Caller: SetCommonHT+0xf0/0x1e8 [mt_7915] [ 14.612000] [ 14.612000] phy_mode=177, ch=36, wdev_type=2 [ 14.616000] ht_cap: ht_cap->HtCapInfo, [ 14.620000] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 14.628000] ht_cap: ht_cap->HtCapParm, [ 14.632000] mdpu_density=0, ampdu_factor=3 [ 14.640000] mt_service_init: wlan service inits successfully! [ 14.644000] WtcSetMaxStaNum: MaxStaNum:248, BssidNum:4, WdsNum:0, MSTANum:2, MaxNumChipRept:32, MinMcastWcid:282 [ 14.788000] RedInit: set CR4/N9 RED Enable to 1. [ 14.792000] RedInit: RED Initiailize Done. [ 14.796000] cp_support_is_enabled: set Driver CP_SUPPORT to Mode 2. [ 14.804000] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 14.808000] wifi_sys_open(), wdev idx = 0 [ 14.812000] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 [ 14.820000] ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 [ 14.824000] BuildChannelList() BandIdx = 0, PhyMode = 78, ChListNum = 13: [ 14.832000] phy_oper_init(): operate TxStream = 2, RxStream = 2 [ 14.836000] mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal [ 14.844000] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 [ 14.856000] BW = 1,TXStream = 2, RXStream = 2, scan(0) [ 14.944000] MtCmdSetTxRxPath: control_chl = 6,control_ch2=0, central_chl = 8, BW = 1,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(0), Channel_Band = 0 [ 14.960000] Caller: wlan_operate_init+0x110/0x19c [mt_7915] [ 14.964000] [ 14.964000] phy_mode=78, ch=6, wdev_type=1 [ 14.972000] ht_cap: ht_cap->HtCapInfo, [ 14.976000] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 14.984000] ht_cap: ht_cap->HtCapParm, [ 14.988000] mdpu_density=5, ampdu_factor=3 [ 14.992000] wdev_attr_update(): wdevId0 = 5c:92:5e:9b:ed:f0 [ 14.996000] AP inf up for ra_0(func_idx) OmacIdx=0 [ 15.000000] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 15.008000] BndStrg_Init() [ 15.008000] ApAutoChannelAtBootUp-----------------> [ 15.016000] ApAutoChannelAtBootUp: AutoChannelBootup[0] = 0 [ 15.020000] MtCmdSetMacTxRx:(ret = 0) [ 15.024000] MtCmdSetMacTxRx:(ret = 0) [ 15.028000] ap_run_at_boot() : ACS is disable !! [ 15.036000] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 15.040000] Caller: SetCommonHT+0xf0/0x1e8 [mt_7915] [ 15.044000] [ 15.044000] phy_mode=78, ch=6, wdev_type=1 [ 15.052000] ht_cap: ht_cap->HtCapInfo, [ 15.056000] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 15.064000] ht_cap: ht_cap->HtCapParm, [ 15.068000] mdpu_density=5, ampdu_factor=3 [ 15.072000] wifi_sys_linkup(), wdev idx = 0 [ 15.076000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1 [ 15.076000] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 15.088000] TRTableInsertMcastEntry:band0 group_idx[0]=0 [ 15.092000] (bssUpdateChannel), ucPrimCh=6, ucCentChSeg0=8, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 15.104000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 [ 15.120000] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (ra0) [ 15.128000] Band0 BcnInitedRnd = 3 [ 15.132000] MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 0, BandIdx: 0 [ 15.136000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 15.140000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 [ 15.156000] BndStrg_SetInfFlags(): BSS(5C:92:5E:9B:ED:F0) set 2G Inf ra0 ready. [ 15.156000] set muru_update_he_cfg()!!!! [ 15.168000] PrintSrCmd: [ 15.168000] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 15.168000] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 15.184000] PrintSrCmd: [ 15.184000] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 15.184000] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 15.196000] PrintSrCmd: [ 15.196000] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 15.196000] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 15.212000] apidx 0 for WscUUIDInit [ 15.216000] Generate UUID for apidx(0) [ 15.224000] rax0: ===> mbss_virtual_if_open [ 15.228000] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 15.236000] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 15.240000] wifi_sys_open(), wdev idx = 2 [ 15.244000] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 [ 15.252000] ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 [ 15.256000] BuildChannelList() BandIdx = 1, PhyMode = 177, ChListNum = 4: [ 15.264000] DfsBuildChannelList(): Done [ 15.268000] phy_oper_init(): operate TxStream = 2, RxStream = 2 [ 15.272000] [RadarStateCheck] RD_NORMAL_MODE [ 15.280000] mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal [ 15.288000] MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 1 [ 15.296000] BW = 2,TXStream = 2, RXStream = 2, scan(0) [ 15.400000] MtCmdSetTxRxPath: control_chl = 36,control_ch2=0, central_chl = 42, BW = 2,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(0), Channel_Band = 1 [ 15.416000] Caller: wlan_operate_init+0x110/0x19c [mt_7915] [ 15.420000] [ 15.420000] phy_mode=177, ch=36, wdev_type=1 [ 15.428000] ht_cap: ht_cap->HtCapInfo, [ 15.432000] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 15.440000] ht_cap: ht_cap->HtCapParm, [ 15.444000] mdpu_density=5, ampdu_factor=3 [ 15.448000] wdev_attr_update(): wdevId2 = 5c:92:5e:9b:ed:f4 [ 15.452000] AP inf up for ra_2(func_idx) OmacIdx=0 [ 15.456000] AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn [ 15.464000] BndStrg_Init() [ 15.464000] ApAutoChannelAtBootUp-----------------> [ 15.472000] ApAutoChannelAtBootUp: AutoChannelBootup[1] = 0 [ 15.476000] MtCmdSetMacTxRx:(ret = 0) [ 15.480000] MtCmdSetMacTxRx:(ret = 0) [ 15.484000] ap_run_at_boot() : ACS is disable !! [ 15.492000] [PMF]APPMFInit:: apidx=2, MFPC=0, MFPR=0, SHA256=0 [ 15.496000] Caller: SetCommonHT+0xf0/0x1e8 [mt_7915] [ 15.504000] [ 15.504000] phy_mode=177, ch=36, wdev_type=1 [ 15.508000] ht_cap: ht_cap->HtCapInfo, [ 15.512000] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 15.520000] ht_cap: ht_cap->HtCapParm, [ 15.524000] mdpu_density=5, ampdu_factor=3 [ 15.528000] wifi_sys_linkup(), wdev idx = 2 [ 15.532000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1 [ 15.532000] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 15.544000] TRTableInsertMcastEntry:band1 group_idx[2]=2 [ 15.548000] (bssUpdateChannel), ucPrimCh=36, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 15.560000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8192 [ 15.576000] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (ra0) [ 15.584000] Band1 BcnInitedRnd = 8 [ 15.588000] MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 0, BandIdx: 1 [ 15.592000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1 [ 15.600000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1 [ 15.612000] BndStrg_SetInfFlags(): BSS(5C:92:5E:9B:ED:F4) set 5G Inf rax0 ready. [ 15.612000] set muru_update_he_cfg()!!!! [ 15.624000] PrintSrCmd: [ 15.624000] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 15.624000] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 15.640000] PrintSrCmd: [ 15.640000] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 15.640000] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 15.652000] PrintSrCmd: [ 15.652000] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 15.652000] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 15.668000] apidx 2 for WscUUIDInit [ 15.672000] Generate UUID for apidx(2) [ 15.680000] device eth2 entered promiscuous mode [ 15.692000] device rax0 entered promiscuous mode [ 15.728000] device ra0 entered promiscuous mode [ 16.756000] br0: port 3(ra0) entered forwarding state [ 16.764000] br0: port 3(ra0) entered forwarding state [ 16.768000] br0: port 2(rax0) entered forwarding state [ 16.772000] br0: port 2(rax0) entered forwarding state [ 16.780000] br0: port 1(eth2) entered forwarding state [ 16.784000] br0: port 1(eth2) entered forwarding state [ 16.844000] Ebtables v2.0 registered sh: -d: unknown operand [ 17.372000] eth3: ===> VirtualIF_open [ 17.472000] Ralink HW NAT v2.52.0 Module Enabled, FoE Size: 16384 [ 17.480000] EEPROM:Read from [Config] offset 0x1000,length 0xf000. RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory [ 17.732000] client_mt_init 651: init done SendMsgToApply sent a different number of bytes than expected, send -1 byte Lktos Command Execution Failed Please check apply service [ 17.876000] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 0, duty: 100 [ 17.880000] MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 0 [ 17.888000] MtCmdThermalProtectDutyCfg: duty: 100 [ 17.900000] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 1, duty: 50 [ 17.908000] MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 1 [ 17.912000] MtCmdThermalProtectDutyCfg: duty: 50 [ 17.924000] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 2, duty: 40 [ 17.928000] MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 2 [ 17.936000] MtCmdThermalProtectDutyCfg: duty: 40 [ 17.948000] SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 3, duty: 20 [ 17.952000] MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 3 [ 17.960000] MtCmdThermalProtectDutyCfg: duty: 20 [ 17.968000] EEPROM:Read from [Config] offset 0x1000,length 0xf000. [ 17.976000] SetThermalProtectEnable(): band_idx: 1, protection_type: 1, trigger_type: 1 [ 17.984000] SetThermalProtectEnable(): trigger_temp: 110, restore_temp: 100, recheck_time: 5 [ 17.996000] MtCmdThermalProtectEnable: band_idx: 1, protect_type: 1 [ 18.000000] MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 110 [ 18.008000] MtCmdThermalProtectEnable: restore_temp: 100, recheck_time: 5 [ 18.020000] SetThermalProtectEnable(): band_idx: 1, protection_type: 2, trigger_type: 1 [ 18.028000] SetThermalProtectEnable(): trigger_temp: 124, restore_temp: 0, recheck_time: 5 [ 18.036000] MtCmdThermalProtectEnable: band_idx: 1, protect_type: 2 [ 18.044000] MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 124 [ 18.052000] MtCmdThermalProtectEnable: restore_temp: 0, recheck_time: 5 [ 18.060000] (Thermal Protect) Radio Notify. [ 18.064000] band_idx: 1, level_idx: 0 [ 18.084000] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 0, duty: 100 [ 18.092000] MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 0 [ 18.096000] MtCmdThermalProtectDutyCfg: duty: 100 [ 18.108000] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 1, duty: 70 [ 18.116000] MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 1 [ 18.120000] MtCmdThermalProtectDutyCfg: duty: 70 [ 18.132000] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 2, duty: 50 [ 18.140000] MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 2 [ 18.148000] MtCmdThermalProtectDutyCfg: duty: 50 [ 18.160000] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 3, duty: 30 [ 18.164000] MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 3 [ 18.172000] MtCmdThermalProtectDutyCfg: duty: 30 [ 18.184000] SetThermalProtectEnable(): band_idx: 0, protection_type: 1, trigger_type: 1 [ 18.192000] SetThermalProtectEnable(): trigger_temp: 110, restore_temp: 100, recheck_time: 5 [ 18.200000] MtCmdThermalProtectEnable: band_idx: 0, protect_type: 1 [ 18.208000] MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 110 [ 18.212000] MtCmdThermalProtectEnable: restore_temp: 100, recheck_time: 5 [ 18.228000] SetThermalProtectEnable(): band_idx: 0, protection_type: 2, trigger_type: 1 [ 18.236000] SetThermalProtectEnable(): trigger_temp: 124, restore_temp: 0, recheck_time: 5 [ 18.244000] MtCmdThermalProtectEnable: band_idx: 0, protect_type: 2 [ 18.252000] MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 124 [ 18.256000] MtCmdThermalProtectEnable: restore_temp: 0, recheck_time: 5 [ 18.264000] (Thermal Protect) Radio Notify. [ 18.268000] band_idx: 0, level_idx: 0 Thread ApplyExecuteReload: Started! 2015-01-01 00:00:17: (log.c.97) server started [ 18.596000] Load Ralink WDG Timer Module rstats Copyright (C) 2006-2009 Jonathan Zarate event signal: User defined signal 1 rc notification: restart_ss_server [ 18.768000] br0: port 3(ra0) entered forwarding state [ 18.776000] br0: port 2(rax0) entered forwarding state rc notification: start_vpn_client [ 18.788000] br0: port 1(eth2) entered forwarding state rc notification: restart_firewall_wan RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory TOTOLINK login: event signal: User defined signal 1 event signal: User defined signal 1 event signal: User defined signal 1 rc notification: control_wifi_guest_wl_off event signal: User defined signal 1 rc notification: control_wifi_radio_wl_on killall: bndstrg: no process killed rc notification: control_wifi_guest_rt_off rc notification: control_wifi_radio_rt_on


U-Boot 1.1.3 (Jun 29 2020 - 14:15:59) Board: Ralink APSoC DRAM: 256 MB mtk gpio init : BTN_RST pin 4. Config XHCI 40M PLL flash manufacture id: 1c, device id 70 18 find flash: EN25QH128 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.3.0-256 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Jun 29 2020 Time:14:15:59 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size = 256 Mbytes #Reset_MT7530 #Turn on MT7530 LED set LAN/WAN LLLLW Press press RST button for more than 2 seconds to run web failsafe mode RST button is pressed for: 0 second(s) Catution: RST button wasn't pressed or not long enough! Continuing normal boot... Waitting for network init complete : 5 5 4 3 2 1 regValue=[0x0] Port3 Link DOWN! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 6: Load Flash code then burn to Flash via TFTP. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP.


(I didn't connect to serial, so only dmesg output here for now)

[ 0.000000] Linux version 5.4.94 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15668-d33cd383ed)) #0 SMP Mon Feb 1 18:10:43 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is TOTOLINK X5000R [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344 [ 0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00050881 [ 0.000000] Readback ErrCtl register=00050881 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 250280K/262144K available (6060K kernel code, 204K rwdata, 1288K rodata, 1268K init, 238K bss, 11864K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.007800] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.041997] pid_max: default: 32768 minimum: 301 [ 0.046774] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.064391] rcu: Hierarchical SRCU implementation. [ 0.069828] smp: Bringing up secondary CPUs ... [ 0.075960] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.075971] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.075983] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.076083] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.102589] Synchronize counters for CPU 1: done. [ 0.143565] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.143572] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.143580] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.143638] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.171376] Synchronize counters for CPU 2: done. [ 0.202748] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.202755] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.202764] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.202824] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.229235] Synchronize counters for CPU 3: done. [ 0.259113] smp: Brought up 1 node, 4 CPUs [ 0.267351] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.277038] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.284049] pinctrl core: initialized pinctrl subsystem [ 0.290993] NET: Registered protocol family 16 [ 0.307332] FPU Affinity set after 4688 emulations [ 0.322884] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.334143] clocksource: Switched to clocksource GIC [ 0.340899] NET: Registered protocol family 2 [ 0.346447] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.354893] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.362487] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.369569] TCP: Hash tables configured (established 2048 bind 2048) [ 0.376007] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.382481] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.389692] NET: Registered protocol family 1 [ 0.394014] PCI: CLS 0 bytes, default 32 [ 0.490102] 4 CPUs re-calibrate udelay(lpj = 1167360) [ 0.495444] random: fast init done [ 0.496792] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.517252] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.523023] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.534560] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.543799] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.549636] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.555443] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.561733] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.571326] printk: console [ttyS0] disabled [ 0.575626] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.584613] printk: console [ttyS0] enabled [ 0.592875] printk: bootconsole [early0] disabled [ 0.605226] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 0.611530] spi-nor spi0.0: en25qh128 (16384 Kbytes) [ 0.616598] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.622965] Creating 4 MTD partitions on "spi0.0": [ 0.627771] 0x000000000000-0x000000030000 : "u-boot" [ 0.634235] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.640794] 0x000000040000-0x000000050000 : "factory" [ 0.647153] 0x000000050000-0x000001000000 : "firmware" [ 0.653828] 2 uimage-fw partitions found on MTD device firmware [ 0.659807] Creating 2 MTD partitions on "firmware": [ 0.664800] 0x000000000000-0x000000266c4b : "kernel" [ 0.671106] 0x000000266c4b-0x000000fb0000 : "rootfs" [ 0.677406] mtd: device 5 (rootfs) set to be root filesystem [ 0.683192] 1 squashfs-split partitions found on MTD device rootfs [ 0.689379] 0x000000560000-0x000000fb0000 : "rootfs_data" [ 0.697094] libphy: Fixed MDIO Bus: probed [ 0.728536] libphy: mdio: probed [ 0.732032] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.741464] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 0.751932] mt7621-pci 1e140000.pcie: Parsing DT failed [ 0.760029] NET: Registered protocol family 10 [ 0.765917] Segment Routing with IPv6 [ 0.769739] NET: Registered protocol family 17 [ 0.774264] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.787423] 8021q: 802.1Q VLAN Support v1.8 [ 0.793551] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.810015] libphy: dsa slave smi: probed [ 0.814583] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 0.824267] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 0.833958] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 0.843656] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 0.853429] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 0.863169] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 0.874410] DSA: tree 0 setup [ 0.877708] rt2880-pinmux pinctrl: pcie is already enabled [ 0.883217] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 0.890832] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 0.898420] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.005953] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.011542] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.117177] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.124136] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.129011] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.133893] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.143354] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.149720] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.156592] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.163463] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.168985] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.175030] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.181295] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.187630] pci 0000:00:00.0: supports D1 [ 1.191644] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.197772] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.203821] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.210107] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.216429] pci 0000:00:01.0: supports D1 [ 1.220441] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.227398] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.235414] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.243615] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280 [ 1.249688] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.256919] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.264149] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.271484] pci 0000:01:00.0: supports D1 D2 [ 1.275758] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.282401] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.297385] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.302640] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.308728] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.315512] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.322733] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.329552] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280 [ 1.335626] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.342864] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.350111] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.357440] pci 0000:02:00.0: supports D1 D2 [ 1.361712] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.368354] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.383364] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.388603] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.394695] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.401474] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.408694] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.415360] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.421966] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.428925] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 1.435543] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.442501] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.449284] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 1.456501] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff] [ 1.463289] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref] [ 1.470507] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff] [ 1.477293] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff] [ 1.484081] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 1.490867] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 1.497662] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 1.505410] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 1.513159] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 1.520906] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.525871] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 1.532654] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.539439] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref] [ 1.546664] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref] [ 1.554413] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref] [ 1.562168] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref] [ 1.569909] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.574877] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 1.581656] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff] [ 1.588440] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref] [ 1.596442] hctosys: unable to open rtc device (rtc0) [ 1.605827] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.617243] Freeing unused kernel memory: 1268K [ 1.621829] This architecture does not have kernel memory protection. [ 1.628263] Run /sbin/init as init process [ 1.633154] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 2.106948] init: Console is alive [ 2.110600] init: - watchdog - [ 2.682545] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.770810] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.786456] init: - preinit - [ 3.461878] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 3.470235] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 3.478701] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3.602548] random: jshn: uninitialized urandom read (4 bytes read) [ 3.663806] random: jshn: uninitialized urandom read (4 bytes read) [ 3.700393] random: jshn: uninitialized urandom read (4 bytes read) [ 3.906913] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 3.913969] 8021q: adding VLAN 0 to HW filter on device lan1 [ 6.990639] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off [ 6.997984] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 8.158920] jffs2: notice: (585) jffs2_build_xattr_subsystem: complete building xattr subsystem, 43 of xdatum (25 unchecked, 17 orphan) and 60 of xref (17 dead, 0 orphan) found. [ 8.179581] mount_root: switching to jffs2 overlay [ 8.189628] overlayfs: upper fs does not support tmpfile. [ 8.203189] urandom-seed: Seeding with /etc/urandom.seed [ 8.339839] mt7530 mdio-bus:1f lan1: Link is Down [ 8.360200] procd: - early - [ 8.363259] procd: - watchdog - [ 8.950273] procd: - watchdog - [ 8.954697] procd: - ubus - [ 9.012488] procd: - init - [ 9.504783] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.558698] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1 [ 9.566190] Backport generated by backports.git v5.8.18-1-0-ga630fd46 [ 9.618060] xt_time: kernel timezone is -0000 [ 9.678412] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 9.683859] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 9.689534] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002) [ 9.695600] urngd: v1.0.2 started. [ 9.699749] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24 [ 9.705236] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 9.710924] mt7915e 0000:02:00.0: enabling device (0000 -> 0002) [ 9.839407] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20200819112315a [ 9.839407] [ 9.839846] random: crng init done [ 9.852547] random: 7 urandom warning(s) missed due to ratelimiting [ 10.159988] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20200819112349 [ 10.194193] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20200819112407 [ 10.335010] PPP generic driver version 2.4.2 [ 10.340739] NET: Registered protocol family 24 [ 10.397713] kmodloader: done loading kernel modules from /etc/modules.d/* [ 16.619932] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 16.627074] mtk_soc_eth 1e100000.ethernet: PPE table busy [ 16.643064] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 16.651378] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 16.655009] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 16.668528] 8021q: adding VLAN 0 to HW filter on device lan1 [ 16.677619] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.684708] br-lan: port 1(lan1) entered blocking state [ 16.690193] br-lan: port 1(lan1) entered disabled state [ 16.696657] device lan1 entered promiscuous mode [ 16.701437] device eth0 entered promiscuous mode [ 16.721891] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 16.729138] 8021q: adding VLAN 0 to HW filter on device lan2 [ 16.738731] br-lan: port 2(lan2) entered blocking state [ 16.744042] br-lan: port 2(lan2) entered disabled state [ 16.750558] device lan2 entered promiscuous mode [ 16.764741] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 16.772023] 8021q: adding VLAN 0 to HW filter on device lan3 [ 16.781734] br-lan: port 3(lan3) entered blocking state [ 16.787063] br-lan: port 3(lan3) entered disabled state [ 16.793717] device lan3 entered promiscuous mode [ 16.809487] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 16.816819] 8021q: adding VLAN 0 to HW filter on device lan4 [ 16.825653] br-lan: port 4(lan4) entered blocking state [ 16.830996] br-lan: port 4(lan4) entered disabled state [ 16.839118] device lan4 entered promiscuous mode [ 16.862227] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 16.869638] 8021q: adding VLAN 0 to HW filter on device wan [ 19.255156] br-lan: port 5(wlan0) entered blocking state [ 19.260591] br-lan: port 5(wlan0) entered disabled state [ 19.266888] device wlan0 entered promiscuous mode [ 19.440999] br-lan: port 6(wlan1) entered blocking state [ 19.446393] br-lan: port 6(wlan1) entered disabled state [ 19.452414] device wlan1 entered promiscuous mode [ 19.457459] br-lan: port 6(wlan1) entered blocking state [ 19.462843] br-lan: port 6(wlan1) entered forwarding state [ 19.468645] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 19.726803] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off [ 19.736575] br-lan: port 1(lan1) entered blocking state [ 19.741933] br-lan: port 1(lan1) entered forwarding state [ 20.270349] br-lan: port 6(wlan1) entered disabled state [ 27.116174] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 27.122925] br-lan: port 5(wlan0) entered blocking state [ 27.128265] br-lan: port 5(wlan0) entered forwarding state [ 81.559422] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 81.566179] br-lan: port 6(wlan1) entered blocking state [ 81.571506] br-lan: port 6(wlan1) entered forwarding state


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1