TOTOLINK X5000R

Totolink X5000R

Supported since this commit (2020-10-25)

CPU Ram Flash Network WLAN Serial Power
Mediatek MT7621 (mips, dual core, 880 MHz) 256 MiB 16 MiB 5x 1 Gbit WiFi 6 (802.11ax) Pads on board 12V 1A
  1. → Download the snapshot image
  2. → Flash using OEM web UI
Architecture MIPS 1004Kc
Vendor Mediatek
Bootloader U-Boot
System-On-Chip Mediatek MT7621A
CPU/Speed 880 MHz ?
Flash-Chip Nanya NT5CC128M16IP
Flash size 16 MiB
RAM 256 MiB
Wireless MT 7615 dual radio 802.11ax
Ethernet 10/100 Mbit/s w/ vlan support
Serial Pads on board

Product image Device opened

Top of the PCB, tape over connectors removed Bottom od the PCB

There are 4 screws and a lot of plastic clips. No screws behind stickers or anything.

(I didn't connect to serial, so only dmesg output here for now)

[ 0.000000] Linux version 5.4.94 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15668-d33cd383ed)) #0 SMP Mon Feb 1 18:10:43 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is TOTOLINK X5000R [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344 [ 0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00050881 [ 0.000000] Readback ErrCtl register=00050881 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 250280K/262144K available (6060K kernel code, 204K rwdata, 1288K rodata, 1268K init, 238K bss, 11864K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.007800] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.041997] pid_max: default: 32768 minimum: 301 [ 0.046774] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.064391] rcu: Hierarchical SRCU implementation. [ 0.069828] smp: Bringing up secondary CPUs ... [ 0.075960] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.075971] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.075983] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.076083] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.102589] Synchronize counters for CPU 1: done. [ 0.143565] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.143572] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.143580] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.143638] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.171376] Synchronize counters for CPU 2: done. [ 0.202748] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.202755] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.202764] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.202824] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.229235] Synchronize counters for CPU 3: done. [ 0.259113] smp: Brought up 1 node, 4 CPUs [ 0.267351] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.277038] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.284049] pinctrl core: initialized pinctrl subsystem [ 0.290993] NET: Registered protocol family 16 [ 0.307332] FPU Affinity set after 4688 emulations [ 0.322884] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.334143] clocksource: Switched to clocksource GIC [ 0.340899] NET: Registered protocol family 2 [ 0.346447] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.354893] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.362487] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.369569] TCP: Hash tables configured (established 2048 bind 2048) [ 0.376007] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.382481] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.389692] NET: Registered protocol family 1 [ 0.394014] PCI: CLS 0 bytes, default 32 [ 0.490102] 4 CPUs re-calibrate udelay(lpj = 1167360) [ 0.495444] random: fast init done [ 0.496792] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.517252] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.523023] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.534560] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.543799] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.549636] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.555443] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.561733] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.571326] printk: console [ttyS0] disabled [ 0.575626] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.584613] printk: console [ttyS0] enabled [ 0.592875] printk: bootconsole [early0] disabled [ 0.605226] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 0.611530] spi-nor spi0.0: en25qh128 (16384 Kbytes) [ 0.616598] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.622965] Creating 4 MTD partitions on "spi0.0": [ 0.627771] 0x000000000000-0x000000030000 : "u-boot" [ 0.634235] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.640794] 0x000000040000-0x000000050000 : "factory" [ 0.647153] 0x000000050000-0x000001000000 : "firmware" [ 0.653828] 2 uimage-fw partitions found on MTD device firmware [ 0.659807] Creating 2 MTD partitions on "firmware": [ 0.664800] 0x000000000000-0x000000266c4b : "kernel" [ 0.671106] 0x000000266c4b-0x000000fb0000 : "rootfs" [ 0.677406] mtd: device 5 (rootfs) set to be root filesystem [ 0.683192] 1 squashfs-split partitions found on MTD device rootfs [ 0.689379] 0x000000560000-0x000000fb0000 : "rootfs_data" [ 0.697094] libphy: Fixed MDIO Bus: probed [ 0.728536] libphy: mdio: probed [ 0.732032] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.741464] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 0.751932] mt7621-pci 1e140000.pcie: Parsing DT failed [ 0.760029] NET: Registered protocol family 10 [ 0.765917] Segment Routing with IPv6 [ 0.769739] NET: Registered protocol family 17 [ 0.774264] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.787423] 8021q: 802.1Q VLAN Support v1.8 [ 0.793551] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.810015] libphy: dsa slave smi: probed [ 0.814583] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 0.824267] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 0.833958] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 0.843656] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 0.853429] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 0.863169] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 0.874410] DSA: tree 0 setup [ 0.877708] rt2880-pinmux pinctrl: pcie is already enabled [ 0.883217] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 0.890832] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 0.898420] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.005953] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.011542] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.117177] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.124136] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.129011] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.133893] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.143354] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.149720] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.156592] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.163463] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.168985] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.175030] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.181295] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.187630] pci 0000:00:00.0: supports D1 [ 1.191644] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.197772] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.203821] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.210107] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.216429] pci 0000:00:01.0: supports D1 [ 1.220441] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.227398] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.235414] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.243615] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280 [ 1.249688] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.256919] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.264149] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.271484] pci 0000:01:00.0: supports D1 D2 [ 1.275758] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.282401] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.297385] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.302640] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.308728] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.315512] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.322733] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.329552] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280 [ 1.335626] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.342864] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.350111] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.357440] pci 0000:02:00.0: supports D1 D2 [ 1.361712] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.368354] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.383364] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.388603] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.394695] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.401474] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.408694] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.415360] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.421966] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.428925] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 1.435543] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.442501] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.449284] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 1.456501] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff] [ 1.463289] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref] [ 1.470507] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff] [ 1.477293] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff] [ 1.484081] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 1.490867] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 1.497662] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 1.505410] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 1.513159] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 1.520906] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.525871] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 1.532654] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.539439] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref] [ 1.546664] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref] [ 1.554413] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref] [ 1.562168] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref] [ 1.569909] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.574877] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 1.581656] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff] [ 1.588440] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref] [ 1.596442] hctosys: unable to open rtc device (rtc0) [ 1.605827] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.617243] Freeing unused kernel memory: 1268K [ 1.621829] This architecture does not have kernel memory protection. [ 1.628263] Run /sbin/init as init process [ 1.633154] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 2.106948] init: Console is alive [ 2.110600] init: - watchdog - [ 2.682545] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.770810] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.786456] init: - preinit - [ 3.461878] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 3.470235] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 3.478701] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3.602548] random: jshn: uninitialized urandom read (4 bytes read) [ 3.663806] random: jshn: uninitialized urandom read (4 bytes read) [ 3.700393] random: jshn: uninitialized urandom read (4 bytes read) [ 3.906913] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 3.913969] 8021q: adding VLAN 0 to HW filter on device lan1 [ 6.990639] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off [ 6.997984] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 8.158920] jffs2: notice: (585) jffs2_build_xattr_subsystem: complete building xattr subsystem, 43 of xdatum (25 unchecked, 17 orphan) and 60 of xref (17 dead, 0 orphan) found. [ 8.179581] mount_root: switching to jffs2 overlay [ 8.189628] overlayfs: upper fs does not support tmpfile. [ 8.203189] urandom-seed: Seeding with /etc/urandom.seed [ 8.339839] mt7530 mdio-bus:1f lan1: Link is Down [ 8.360200] procd: - early - [ 8.363259] procd: - watchdog - [ 8.950273] procd: - watchdog - [ 8.954697] procd: - ubus - [ 9.012488] procd: - init - [ 9.504783] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.558698] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1 [ 9.566190] Backport generated by backports.git v5.8.18-1-0-ga630fd46 [ 9.618060] xt_time: kernel timezone is -0000 [ 9.678412] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 9.683859] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 9.689534] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002) [ 9.695600] urngd: v1.0.2 started. [ 9.699749] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24 [ 9.705236] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 9.710924] mt7915e 0000:02:00.0: enabling device (0000 -> 0002) [ 9.839407] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20200819112315a [ 9.839407] [ 9.839846] random: crng init done [ 9.852547] random: 7 urandom warning(s) missed due to ratelimiting [ 10.159988] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20200819112349 [ 10.194193] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20200819112407 [ 10.335010] PPP generic driver version 2.4.2 [ 10.340739] NET: Registered protocol family 24 [ 10.397713] kmodloader: done loading kernel modules from /etc/modules.d/* [ 16.619932] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 16.627074] mtk_soc_eth 1e100000.ethernet: PPE table busy [ 16.643064] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 16.651378] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 16.655009] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 16.668528] 8021q: adding VLAN 0 to HW filter on device lan1 [ 16.677619] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.684708] br-lan: port 1(lan1) entered blocking state [ 16.690193] br-lan: port 1(lan1) entered disabled state [ 16.696657] device lan1 entered promiscuous mode [ 16.701437] device eth0 entered promiscuous mode [ 16.721891] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 16.729138] 8021q: adding VLAN 0 to HW filter on device lan2 [ 16.738731] br-lan: port 2(lan2) entered blocking state [ 16.744042] br-lan: port 2(lan2) entered disabled state [ 16.750558] device lan2 entered promiscuous mode [ 16.764741] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 16.772023] 8021q: adding VLAN 0 to HW filter on device lan3 [ 16.781734] br-lan: port 3(lan3) entered blocking state [ 16.787063] br-lan: port 3(lan3) entered disabled state [ 16.793717] device lan3 entered promiscuous mode [ 16.809487] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 16.816819] 8021q: adding VLAN 0 to HW filter on device lan4 [ 16.825653] br-lan: port 4(lan4) entered blocking state [ 16.830996] br-lan: port 4(lan4) entered disabled state [ 16.839118] device lan4 entered promiscuous mode [ 16.862227] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 16.869638] 8021q: adding VLAN 0 to HW filter on device wan [ 19.255156] br-lan: port 5(wlan0) entered blocking state [ 19.260591] br-lan: port 5(wlan0) entered disabled state [ 19.266888] device wlan0 entered promiscuous mode [ 19.440999] br-lan: port 6(wlan1) entered blocking state [ 19.446393] br-lan: port 6(wlan1) entered disabled state [ 19.452414] device wlan1 entered promiscuous mode [ 19.457459] br-lan: port 6(wlan1) entered blocking state [ 19.462843] br-lan: port 6(wlan1) entered forwarding state [ 19.468645] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 19.726803] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off [ 19.736575] br-lan: port 1(lan1) entered blocking state [ 19.741933] br-lan: port 1(lan1) entered forwarding state [ 20.270349] br-lan: port 6(wlan1) entered disabled state [ 27.116174] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 27.122925] br-lan: port 5(wlan0) entered blocking state [ 27.128265] br-lan: port 5(wlan0) entered forwarding state [ 81.559422] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 81.566179] br-lan: port 6(wlan1) entered blocking state [ 81.571506] br-lan: port 6(wlan1) entered forwarding state


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/02/10 17:01
  • by peetz0r