Show pagesourceOld revisionsBacklinksBack to top × Dataentry Device Type: WiFi Router Brand: THOMSON Model: ST780 WL SpeedToutch2c2733 CPU: BROADCOM BCM6348KPBG HN0708 P20 Package architecture:ADSL2+, MIPS 32 CPU RAM MB: 16 (SAMSUNG 713 K4S281632I-UC75) Flash Memory MB : 4 ? (Spansion S29GL 032A90TFIR4) Switch: BROADCOM BCM5325E KQMG Ethernet 100M ports: 4 USB ports: 1 Serial parameters yes (-b 9600) Flash Memory OEM firmware bootlog Unzipping started UNZIP DONE → starting bootloader Speedtouch initialization sequence started. Secondary boot Unzipping started UNZIP DONE → starting uncompressed file Speedtouch initialization sequence started. ÿ [OSI2] File “/ZZOGDZ6.2H5”: Format OSI2 compliant (offset=340, prodid=“0”, varid=“0”). [SS] Device mounted (prodid=“0”, prodname=“SpeedTouch 780”, varid=“0”, varname=“”). [ELF] Loading file “/ZZOGDZ6.2H5” … call Speedtouch initialization sequence started. loading : firmware/pob6w_init Calibrating delay loop… ts archfs opened /ZZOGDZ6.2H5 offset 2203507 loading : firmware/pots/ZZW6AA.gz lmem size 53772 sdram size 390932 pSdramPHY=0xA0FFFFF8, 0x1B790C 0xDEADBEEF AdslCoreHwReset: AdslOemDataAddr = 0xA0FFD252.31 BogoMIPS mpi: device 0x4318 found in PCI slot 1, function 0 E24 wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: using main broad MAC address base in NVRAM (wombo board srom: 1 ) wl0 MAC Address: MA:CMA:CMA:CMA:CM:AC For EMAC2 - select for non-managed switch (single EMAC). appl_init: BUILD VERIFIED! 3.131.35.1.cpe0.0: Broadcom BCM4318 802.11 Wireless Controller Build startup 8068b90cv [IGD-MBUS] in igd_mbus_init(), register s_mbus_igd. [IGD-MBUS] IGD IPInterface successfully registered. [IGD-MBUS] mbus object type WANPPPConnection successfully registered [IGD-MBUS] mbus object type WANIPConnection successfully registered [IGD-MBUS] mbus object type WANDSLInterfaceConfig successfully registered [IGD-MBUS] mbus object type WANConnectionDevice successfully registered [IGD-MBUS] IGD NATApplicationList successfully registered. [IGD-MBUS] mbus object type DYNDNS successfully registered [IGD-MBUS] mbus object type Internet successfully registered [IGD-MBUS] mbus igd object type VoiceServices.Capabilities successfully registered [IGD-MBUS] mbus object type voiceprofile successfully registered [IGD-MBUS] mbus object type VoiceServices successfully registered SNTP: SERVMGMT initialized: success! archfs opened /ZZOGDZ6.2H5 offset 2203507 archfs opened /ZZOGDZ6.2H5 offset 2203507 <4> SysUpTime: 00:00:01 KERNEL Cold restart [EXPR] intf _intf_0 new() [EXPR] ip _addr_127_0_0_1 new() archfs opened /ZZOGDZ6.2H5 offset 2203507 ************* ERROR RECORD ************* time : 000000:00:00.000000 Application /ZZOGDZ6.2H5 started after POWERON. ****************** END ***************** Failed to attach PPP interface: interface not configured. The entry could not be added: it exists already! Username : work ok for SpeedToutch2c2733 Set the Speedtouch/Thomson/Technicolor Modem into BOOTP mode: Press the recessed reset button on the rear of the modem using a paperclip. After a while thelights go off and power turns to red. Then the power will change to orange and the ethernetlight will intermediately flash green. When the power is orange and the ethernet flashes greenthe device is in BOOTP mode and you have to let go of the reset button. BOOTP reason : BLFLAG_BUTTON_PUSH ————————————– Unzipping started UNZIP DONE → starting bootloader Speedtouch initialization sequence started. BOOTP reason : BLFLAG_BUTTON_PUSH phy_bcm6348.c - ETHD: external phy is used Ctrl: BOOTP initiated. Ctrl: BOOTP Reply timeout. *Reseting the board* Unzipping started NZIP DONE → starting bootloader Speedtouch initialization sequence started. … sudo service isc-dhcp-server status —— isc-dhcp-server.service - ISC DHCP IPv4 server Loaded: loaded (/lib/systemd/system/isc-dhcp-server.service; enabled; vendor preset: enabled)\\ Active: active (running) since Sun 2021-01-03 19:12:08 EET; 3s ago\\ Docs: man:dhcpd(8)\\ Main PID: 38886 (dhcpd)\\ Tasks: 4 (limit: 13862)\\ Memory: 5.2M\\ CGroup: /system.slice/isc-dhcp-server.service\\ └─38886 dhcpd -user dhcpd -group dhcpd -f -4 -pf /run/dhcp-server/dhcpd.pid -cf /etc/dhcp/dhcpd.conf\\ Jan 03 19:12:08 odyssey dhcpd[38886]: Wrote 3 leases to leases file. Jan 03 19:12:08 odyssey dhcpd[38886]: Listening on LPF/enp3s1/yy:yy:yy:yy:yy:yy/192.168.1.0/24 Jan 03 19:12:08 odyssey sh[38886]: Listening on LPF/enp3s1/yy:yy:yy:yy:yy:yy/192.168.1.0/24 Jan 03 19:12:08 odyssey sh[38886]: Sending on LPF/enp3s1/yy:yy:yy:yy:yy:yy/192.168.1.0/24 Jan 03 19:12:08 odyssey sh[38886]: Sending on Socket/fallback/fallback-net Jan 03 19:12:08 odyssey dhcpd[38886]: Sending on LPF/enp3s1/yy:yy:yy:yy:yy:yy/192.168.1.0/24 Jan 03 19:12:08 odyssey dhcpd[38886]: Sending on Socket/fallback/fallback-net Jan 03 19:12:08 odyssey dhcpd[38886]: Server starting service. Jan 03 19:12:08 odyssey dhcpd[38886]: BOOTREQUEST from xx:xx:xx:xx:xx:xx via enp3s1 Jan 03 19:12:08 odyssey dhcpd[38886]: BOOTREPLY for 192.168.1.175 to bla1 (xx:xx:xx:xx:xx:xx) via enp3s1 Router ***Reseting the board*** Unzipping started UNZIP DONE → starting bootloader Speedtouch initialization sequence started. BOOTP reason : BLFLAG_INV_DOWNLOAD phy_bcm6348.c - ETHD: external phy is used USB Link UP. Ctrl: BOOTP initiated. USB_ACTIVE Ctrl: BOOTP Reply received! * Own IP = 192.168.1.175 () * Server = 192.168.1.1 () * Mask = 255.255.255.0 * Filename = BANT-R Ctrl: TFTP started (Rx:BANT-R). TFTP [0] - aborted (1) : File not found [ERROR] : BLI2 verify update fini ! This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies Last modified: 2021/01/05 05:24by antares