Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revisionBoth sides next revision | ||
| toh:tenda:4g301 [2015/12/02 18:46] – New bootlog formatting applied tmomas | toh:tenda:4g301 [2015/12/02 18:49] – tags added tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Tenda 4G301 ====== | ||
| + | |||
| + | ====Serial Port==== | ||
| + | ===Pinout=== | ||
| + | On the other side of the PCB there are 2 test points. | ||
| + | |||
| + | The serial interface is 3.3V TTL levels (need USB cable and/or level converter to connect to a PC). Settings are 57k6 8N1 no flow control. | ||
| + | |||
| + | ====GPIO==== | ||
| + | * in 2: button or usb-charging power | ||
| + | * out 0: usb-power | ||
| + | * out 2: LED 1 | ||
| + | * out 40: LED 5 | ||
| + | * out 41/42: LED 2 (incl.red one) | ||
| + | * out 43: LED 4 | ||
| + | |||
| + | ===== Bootlogs ===== | ||
| + | ==== OEM bootlog ==== | ||
| + | |||
| + | <WRAP bootlog> | ||
| + | < | ||
| + | |||
| + | |||
| + | Board: Ralink APSoC DRAM: 64 MB | ||
| + | |||
| + | relocate_code Pointer at: 83fb4000 | ||
| + | |||
| + | enable ephy clock...done. rf reg 29 = 5 | ||
| + | |||
| + | SSC disabled. | ||
| + | |||
| + | spi_wait_nsec: | ||
| + | |||
| + | spi device id: ef 40 16 0 0 (40160000) | ||
| + | |||
| + | find flash: W25Q32BV | ||
| + | |||
| + | raspi_read: from:30000 len:1000 | ||
| + | |||
| + | *** Warning - bad CRC, using default environment | ||
| + | |||
| + | |||
| + | ============================================ | ||
| + | |||
| + | Ralink UBoot Version: 4.1.1.0 | ||
| + | |||
| + | -------------------------------------------- | ||
| + | |||
| + | ASIC 7620_MP (Port5< | ||
| + | |||
| + | DRAM component: 512 Mbits DDR, width 16 | ||
| + | |||
| + | DRAM bus: 16 bit | ||
| + | |||
| + | Total memory: 64 MBytes | ||
| + | |||
| + | Flash component: SPI Flash | ||
| + | |||
| + | Date:Oct 21 2013 Time: | ||
| + | |||
| + | ============================================ | ||
| + | |||
| + | icache: sets:512, ways:4, linesz:32 , | ||
| + | |||
| + | dcache: sets:256, ways:4, linesz:32 , | ||
| + | |||
| + | |||
| + | ##### The CPU freq = 580 MHZ #### | ||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | Please choose the operation: | ||
| + | |||
| + | 1: Load system code to SDRAM via TFTP. | ||
| + | |||
| + | 2: Load system code then write to Flash via TFTP. | ||
| + | |||
| + | 3: Boot system code via Flash (default). | ||
| + | |||
| + | 4: Entr boot command line interface. | ||
| + | |||
| + | 7: Load Boot Loader code then write to Flash via Serial. | ||
| + | |||
| + | 9: Load Boot Loader code then write to Flash via TFTP. 0 | ||
| + | |||
| + | |||
| + | |||
| + | 3: System Boot system code via Flash. | ||
| + | |||
| + | ## Booting image at bc050000 ... | ||
| + | |||
| + | raspi_read: from:50000 len:40 | ||
| + | |||
| + | Image Name: Linux Kernel Image | ||
| + | |||
| + | Image Type: MIPS Linux Kernel Image (lzma compressed) | ||
| + | |||
| + | Data Size: 2970642 Bytes = 2.8 MB | ||
| + | |||
| + | Load Address: 80000000 | ||
| + | |||
| + | Entry Point: | ||
| + | |||
| + | raspi_read: from:50040 len:2d5412 | ||
| + | |||
| + | | ||
| + | |||
| + | | ||
| + | |||
| + | No initrd | ||
| + | |||
| + | ## Transferring control to Linux (at address 8000c310) ... | ||
| + | |||
| + | ## Giving linux memsize in MB, 64 | ||
| + | |||
| + | |||
| + | Starting kernel ... | ||
| + | |||
| + | |||
| + | |||
| + | LINUX started... | ||
| + | |||
| + | THIS IS ASIC | ||
| + | Linux version 2.6.36 (root@bogon) (gcc version 3.4.2) #143 Sat Jun 21 | ||
| + | 06:03:01 EDT 2014 | ||
| + | |||
| + | The CPU feqenuce set to 580 MHz | ||
| + | |||
| + | MIPS CPU sleep mode enabled. | ||
| + | PCIE: bypass PCIe DLL. | ||
| + | PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 | ||
| + | | ||
| + | PCIE: PLL power down for MT7620N | ||
| + | CPU revision is: 00019650 (MIPS 24Kc) | ||
| + | Determined physical RAM map: | ||
| + | | ||
| + | Initrd not found or empty - disabling initrd | ||
| + | Zone PFN ranges: | ||
| + | Normal | ||
| + | Movable zone start PFN for each node | ||
| + | early_node_map[1] active PFN ranges | ||
| + | 0: 0x00000000 -> 0x00004000 | ||
| + | Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 | ||
| + | Kernel command line: console=ttyS1, | ||
| + | PID hash table entries: 256 (order: -2, 1024 bytes) | ||
| + | Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) | ||
| + | Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) | ||
| + | Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. | ||
| + | Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | ||
| + | Writing ErrCtl register=0003e67a | ||
| + | Readback ErrCtl register=0003e67a | ||
| + | Memory: 53100k/ | ||
| + | 821k data, 6428k init, 0k highmem) | ||
| + | NR_IRQS:128 | ||
| + | MTK/Ralink System Tick Counter init... cd: | ||
| + | console [ttyS1] enabled | ||
| + | Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) | ||
| + | pid_max: default: 32768 minimum: 301 | ||
| + | Mount-cache hash table entries: 512 | ||
| + | NET: Registered protocol family 16 | ||
| + | bio: create slab < | ||
| + | SCSI subsystem initialized | ||
| + | usbcore: registered new interface driver usbfs | ||
| + | usbcore: registered new interface driver hub | ||
| + | usbcore: registered new device driver usb | ||
| + | cfg80211: Calling CRDA to update world regulatory domain | ||
| + | Switching to clocksource Ralink external timer | ||
| + | NET: Registered protocol family 2 | ||
| + | IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | ||
| + | TCP established hash table entries: 2048 (order: 2, 16384 bytes) | ||
| + | TCP bind hash table entries: 2048 (order: 1, 8192 bytes) | ||
| + | TCP: Hash tables configured (established 2048 bind 2048) | ||
| + | TCP reno registered | ||
| + | UDP hash table entries: 256 (order: 0, 4096 bytes) | ||
| + | UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | ||
| + | NET: Registered protocol family 1 | ||
| + | Load Ralink Timer0 Module | ||
| + | Load Ralink Timer1 Module | ||
| + | RT3xxx EHCI/OHCI init. | ||
| + | fuse init (API version 7.15) | ||
| + | msgmni has been set to 103 | ||
| + | Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) | ||
| + | io scheduler noop registered (default) | ||
| + | Ralink gpio driver initialized | ||
| + | Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled | ||
| + | serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A | ||
| + | serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A | ||
| + | brd: module loaded | ||
| + | deice id : ef 40 16 0 0 (40160000) | ||
| + | W25Q32BV(ef 40160000) (4096 Kbytes) | ||
| + | mtd .name = raspi, .size = 0x00400000 (0M) .erasesize = 0x00000004 (0K) | ||
| + | .numeraseregions = 65536 | ||
| + | Creating 6 MTD partitions on " | ||
| + | 0x000000000000-0x000000400000 : " | ||
| + | 0x000000000000-0x000000030000 : " | ||
| + | 0x000000030000-0x000000040000 : " | ||
| + | 0x000000040000-0x000000050000 : " | ||
| + | 0x000000050000-0x0000003f0000 : " | ||
| + | 0x0000003f0000-0x000000400000 : " | ||
| + | rdm_major = 253 | ||
| + | SMACCR1 -- : 0x0000000c | ||
| + | SMACCR0 -- : 0x43762077 | ||
| + | Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors | ||
| + | allocated, mtu = 1500! | ||
| + | SMACCR1 -- : 0x0000000c | ||
| + | SMACCR0 -- : 0x43762077 | ||
| + | PROC INIT OK! | ||
| + | PPP generic driver version 2.4.2 | ||
| + | PPP BSD Compression module registered | ||
| + | PPP MPPE Compression module registered | ||
| + | NET: Registered protocol family 24 | ||
| + | |||
| + | |||
| + | === pAd = c0003000, size = 806048 === | ||
| + | |||
| + | <-- RTMPAllocTxRxRingMemory, | ||
| + | <-- RTMPAllocAdapterBlock, | ||
| + | AP Driver version-2.7.1.6 | ||
| + | ehci_hcd: USB 2.0 ' | ||
| + | rt3xxx-ehci rt3xxx-ehci: | ||
| + | rt3xxx-ehci rt3xxx-ehci: | ||
| + | rt3xxx-ehci rt3xxx-ehci: | ||
| + | rt3xxx-ehci rt3xxx-ehci: | ||
| + | hub 1-0:1.0: USB hub found | ||
| + | hub 1-0:1.0: 1 port detected | ||
| + | ohci_hcd: USB 1.1 ' | ||
| + | rt3xxx-ohci rt3xxx-ohci: | ||
| + | rt3xxx-ohci rt3xxx-ohci: | ||
| + | rt3xxx-ohci rt3xxx-ohci: | ||
| + | hub 2-0:1.0: USB hub found | ||
| + | hub 2-0:1.0: 1 port detected | ||
| + | usbcore: registered new interface driver cdc_acm | ||
| + | cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN | ||
| + | adapters | ||
| + | Initializing USB Mass Storage driver... | ||
| + | usbcore: registered new interface driver usb-storage | ||
| + | USB Mass Storage support registered. | ||
| + | usbcore: registered new interface driver ums-usbat | ||
| + | Netfilter messages via NETLINK v0.30. | ||
| + | nf_conntrack version 0.5.0 (829 buckets, 3316 max) | ||
| + | ctnetlink v0.93: registering with nfnetlink. | ||
| + | Create proc webstr success. | ||
| + | matchsize=264 | ||
| + | xt_time: kernel timezone is -0000 | ||
| + | net/ | ||
| + | IPVS: Registered protocols () | ||
| + | IPVS: Connection hash table configured (size=4096, memory=32Kbytes) | ||
| + | IPVS: ipvs loaded. | ||
| + | ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux | ||
| + | TCP cubic registered | ||
| + | NET: Registered protocol family 17 | ||
| + | L2TP core driver, V2.0 | ||
| + | PPPoL2TP kernel driver, V2.0 | ||
| + | 802.1Q VLAN Support v1.8 Ben Greear < | ||
| + | All bugs added by David S. Miller < | ||
| + | Freeing unused kernel memory: 6428k freed | ||
| + | |||
| + | init started: BusyBox v1.12Algorithmics/ | ||
| + | .1 (2014-04-15 05:58:40 EDT) | ||
| + | |||
| + | starting pid 32, tty '': | ||
| + | Welcome to | ||
| + | _______ | ||
| + | | ___ \| | ||
| + | | |___| || |__| || | ||
| + | | | ||
| + | |__| \__\|__| |__||______||__||_| \____||_|\___\ | ||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | starting pid 47, tty '/ | ||
| + | (none) login: SOFT_WARE_VERSION V1.01.27 | ||
| + | SOFT_WARE_VERSION V1.01.27 | ||
| + | LANGUAGE_INFO en | ||
| + | HW_VERSION V1.0 | ||
| + | SVN_VERSION 537 | ||
| + | BUILD_TIME Jun 21 2014 05:57:25 | ||
| + | BACK config init OK, old crc=ace7c67b, | ||
| + | ########## | ||
| + | nvramDestroy=0 | ||
| + | backUPDestroy=0 | ||
| + | ########## | ||
| + | none config destroy..., nothing to do | ||
| + | |||
| + | |||
| + | Yes: | ||
| + | |||
| + | ****** WeLoveLinux ****** | ||
| + | |||
| + | | ||
| + | cat: can't open '/ | ||
| + | sh: cannot create / | ||
| + | directory | ||
| + | usbcore: registered new interface driver usbserial | ||
| + | USB Serial support registered for generic | ||
| + | usbcore: registered new interface driver usbserial_generic | ||
| + | usbserial: USB Serial Driver core | ||
| + | USB Serial support registered for Sierra USB modem | ||
| + | usbcore: registered new interface driver sierra | ||
| + | sierra: v.1.7.16: | ||
| + | USB Serial support registered for GSM modem (1-port) | ||
| + | usbcore: registered new interface driver option | ||
| + | option: v0.7.2:USB Driver for GSM modems | ||
| + | USB Serial support registered for debug | ||
| + | usbcore: registered new interface driver debug | ||
| + | |||
| + | ==>down wireless interface! | ||
| + | RX DESC a32d0000 | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | RTMP_TimerListAdd: | ||
| + | APSDCapable[0]=0 | ||
| + | APSDCapable[1]=0 | ||
| + | APSDCapable[2]=0 | ||
| + | APSDCapable[3]=0 | ||
| + | APSDCapable[4]=0 | ||
| + | APSDCapable[5]=0 | ||
| + | APSDCapable[6]=0 | ||
| + | APSDCapable[7]=0 | ||
| + | APSDCapable[8]=0 | ||
| + | APSDCapable[9]=0 | ||
| + | APSDCapable[10]=0 | ||
| + | APSDCapable[11]=0 | ||
| + | APSDCapable[12]=0 | ||
| + | APSDCapable[13]=0 | ||
| + | APSDCapable[14]=0 | ||
| + | APSDCapable[15]=0 | ||
| + | default ApCliAPSDCapable[0]=0 | ||
| + | 1. Phy Mode = 9 | ||
| + | 2. Phy Mode = 9 | ||
| + | E2PROM: D0 target power=0xff20 | ||
| + | E2PROM: 40 MW Power Delta= 0 | ||
| + | 3. Phy Mode = 9 | ||
| + | AntCfgInit: primary/ | ||
| + | Initialize RF Central Registers for E2 !!! | ||
| + | Initialize RF Central Registers for E3 !!! | ||
| + | Initialize RF Channel Registers for E2 !!! | ||
| + | Initialize RF Channel Registers for E3 !!! | ||
| + | Initialize RF DCCal Registers for E2 !!! | ||
| + | Initialize RF DCCal Registers for E3 !!! | ||
| + | D1 = 0, D2 = 12, CalCode = 28 !!! | ||
| + | RT6352_Temperature_Init : BBPR49 = 0x0 | ||
| + | RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff6 | ||
| + | Current Temperature from BBP_R49=0xfffffff2 | ||
| + | TX BW Filter Calibration !!! | ||
| + | RX BW Filter Calibration !!! | ||
| + | LOFT Calibration Done! | ||
| + | IQCalibration Start! | ||
| + | IQCalibration Done! CH = 0, (gain= f, phase= 1) | ||
| + | IQCalibration Start! | ||
| + | IQCalibration Done! CH = 1, (gain= f, phase= 0) | ||
| + | TX IQ Calibration Done! | ||
| + | internal ALC is not enabled in NVM ! | ||
| + | MCS Set = ff ff 00 00 01 | ||
| + | RTMP_TimerListAdd: | ||
| + | Main bssid = c8: | ||
| + | <==== rt28xx_init, | ||
| + | 0x1300 = 00064380 | ||
| + | Raeth v3.0 (Tasklet, | ||
| + | |||
| + | phy_tx_ring = 0x02d72000, tx_ring = 0xa2d72000 | ||
| + | |||
| + | phy_rx_ring0 = 0x02d73000, rx_ring0 = 0xa2d73000 | ||
| + | SMACCR1 -- : 0x0000000c | ||
| + | SMACCR0 -- : 0x43762077 | ||
| + | CDMA_CSG_CFG = 81000000 | ||
| + | GDMA1_FWD_CFG = 20710000 | ||
| + | This crc is same as Old, ace7c67b, no need to write to flash. | ||
| + | maclist: | ||
| + | WLan[C8: | ||
| + | Lan[C8: | ||
| + | :58] | ||
| + | Wan[C8: | ||
| + | Free TX/RX Ring Memory! | ||
| + | Raeth v3.0 (Tasklet, | ||
| + | |||
| + | phy_tx_ring = 0x02d76000, tx_ring = 0xa2d76000 | ||
| + | |||
| + | phy_rx_ring0 = 0x0336f000, rx_ring0 = 0xa336f000 | ||
| + | SMACCR1 -- : 0x0000c83a | ||
| + | SMACCR0 -- : 0x352f3258 | ||
| + | CDMA_CSG_CFG = 81000000 | ||
| + | GDMA1_FWD_CFG = 20710000 | ||
| + | ifconfig: SIOCSIFHWADDR: | ||
| + | ------------- | ||
| + | WISP_MODE | ||
| + | -------------- | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_ingress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | vconfig: ioctl error for set_egress_map: | ||
| + | switch reg write offset=2004, | ||
| + | switch reg write offset=2104, | ||
| + | switch reg write offset=2204, | ||
| + | switch reg write offset=2304, | ||
| + | switch reg write offset=2404, | ||
| + | switch reg write offset=2504, | ||
| + | switch reg write offset=2010, | ||
| + | switch reg write offset=2110, | ||
| + | switch reg write offset=2210, | ||
| + | switch reg write offset=2310, | ||
| + | switch reg write offset=2410, | ||
| + | switch reg write offset=2510, | ||
| + | switch reg write offset=2610, | ||
| + | switch reg write offset=2710, | ||
| + | switch reg write offset=2604, | ||
| + | switch reg write offset=2704, | ||
| + | switch reg write offset=2610, | ||
| + | switch reg write offset=2014, | ||
| + | switch reg write offset=2114, | ||
| + | switch reg write offset=2214, | ||
| + | switch reg write offset=2314, | ||
| + | switch reg write offset=2414, | ||
| + | switch reg write offset=2514, | ||
| + | device eth2.1 entered promiscuous mode | ||
| + | device eth2 entered promiscuous mode | ||
| + | device eth2.2 entered promiscuous mode | ||
| + | br0: port 2(eth2.2) entering learning state | ||
| + | br0: port 2(eth2.2) entering learning state | ||
| + | br0: port 1(eth2.1) entering learning state | ||
| + | br0: port 1(eth2.1) entering learning state | ||
| + | Unable to open / | ||
| + | Init tQoS dev success. | ||
| + | open /dev/tQoS failed. | ||
| + | Set: phy[0].reg[1] = 3900 | ||
| + | Set: phy[0].reg[2] = 3900 | ||
| + | Set: phy[0].reg[3] = 3900 | ||
| + | device ra0 entered promiscuous mode | ||
| + | br0: port 3(ra0) entering learning state | ||
| + | br0: port 3(ra0) entering learning state | ||
| + | br0: port 2(eth2.2) entering forwarding state | ||
| + | br0: port 1(eth2.1) entering forwarding state | ||
| + | 2000, 1, 1 | ||
| + | usbcore: registered new interface driver cdc_ether | ||
| + | / | ||
| + | ==>up wireless interface sucess!Create check wan thread, tid=00000402, | ||
| + | =====> | ||
| + | version=V1.01.27------------- | ||
| + | br0: port 3(ra0) entering forwarding state | ||
| + | |||
| + | |||
| + | Httpd listen 192.168.2.1: | ||
| + | |||
| + | main--504 | ||
| + | semget error: or exist: File exists | ||
| + | semId has exist 0 | ||
| + | =====> | ||
| + | |||
| + | (none) login:</ | ||
| + | </ | ||
| + | |||
| + | ==== OpenWrt bootlog ==== | ||
| + | |||
| + | starting openwrt via ram-image | ||
| + | <WRAP bootlog> | ||
| + | < | ||
| + | |||
| + | Ralink UBoot Version: 4.1.1.0 | ||
| + | |||
| + | -------------------------------------------- | ||
| + | |||
| + | ASIC 7620_MP (Port5< | ||
| + | |||
| + | DRAM component: 512 Mbits DDR, width 16 | ||
| + | |||
| + | DRAM bus: 16 bit | ||
| + | |||
| + | Total memory: 64 MBytes | ||
| + | |||
| + | Flash component: SPI Flash | ||
| + | |||
| + | Date:Oct 21 2013 Time: | ||
| + | |||
| + | ============================================ | ||
| + | |||
| + | icache: sets:512, ways:4, linesz:32 , | ||
| + | |||
| + | dcache: sets:256, ways:4, linesz:32 , | ||
| + | |||
| + | |||
| + | ##### The CPU freq = 580 MHZ #### | ||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | Please choose the operation: | ||
| + | |||
| + | 1: Load system code to SDRAM via TFTP. | ||
| + | |||
| + | 2: Load system code then write to Flash via TFTP. | ||
| + | |||
| + | 3: Boot system code via Flash (default). | ||
| + | |||
| + | 4: Entr boot command line interface. | ||
| + | |||
| + | 7: Load Boot Loader code then write to Flash via Serial. | ||
| + | |||
| + | 9: Load Boot Loader code then write to Flash via TFTP. | ||
| + | |||
| + | |||
| + | |||
| + | You choosed 1 | ||
| + | 0 | ||
| + | |||
| + | raspi_read: from:40028 len:6 | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | 1: System Load Linux to SDRAM via TFTP. | ||
| + | |||
| + | | ||
| + | |||
| + | Input device IP (192.168.2.1) ==: | ||
| + | |||
| + | Input server IP (192.168.2.64) ==: | ||
| + | |||
| + | Input Linux Kernel filename () ==:uImage | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | Trying Eth0 (10/100-M) | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | TFTP from server 192.168.2.64; | ||
| + | |||
| + | Filename ' | ||
| + | |||
| + | |||
| + | | ||
| + | |||
| + | Loading: Got ARP REPLY, set server/gtwy eth addr (00: | ||
| + | |||
| + | Got it | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################################################################# | ||
| + | |||
| + | ################### | ||
| + | |||
| + | done | ||
| + | |||
| + | Bytes transferred = 3090502 (2f2846 hex) | ||
| + | |||
| + | NetBootFileXferSize= 002f2846 | ||
| + | |||
| + | raspi_read: from:30000 len:10000 | ||
| + | |||
| + | Erasing SPI Flash... | ||
| + | |||
| + | raspi_erase: | ||
| + | |||
| + | . | ||
| + | |||
| + | Writing to SPI Flash... | ||
| + | |||
| + | raspi_write: | ||
| + | |||
| + | . | ||
| + | |||
| + | done | ||
| + | |||
| + | Automatic boot of image at addr 0x80A00000 ... | ||
| + | |||
| + | ## Booting image at 80a00000 ... | ||
| + | |||
| + | Image Name: MIPS OpenWrt Linux-3.18.21 | ||
| + | |||
| + | Image Type: MIPS Linux Kernel Image (lzma compressed) | ||
| + | |||
| + | Data Size: 3090438 Bytes = 2.9 MB | ||
| + | |||
| + | Load Address: 80000000 | ||
| + | |||
| + | Entry Point: | ||
| + | |||
| + | | ||
| + | |||
| + | | ||
| + | |||
| + | No initrd | ||
| + | |||
| + | ## Transferring control to Linux (at address 80000000) ... | ||
| + | |||
| + | ## Giving linux memsize in MB, 64 | ||
| + | |||
| + | |||
| + | Starting kernel ... | ||
| + | |||
| + | |||
| + | [ 0.000000] Linux version 3.18.21 (daniel@box) (gcc version 4.8.3 | ||
| + | (OpenWrt/ | ||
| + | [ 0.000000] Board has DDR2 | ||
| + | [ 0.000000] Analog PMU set to hw control | ||
| + | [ 0.000000] Digital PMU set to hw control | ||
| + | [ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3 | ||
| + | [ 0.000000] bootconsole [early0] enabled | ||
| + | [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) | ||
| + | [ 0.000000] MIPS: machine is Tenda 4G301 | ||
| + | [ 0.000000] Determined physical RAM map: | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Initrd not found or empty - disabling initrd | ||
| + | [ 0.000000] Zone ranges: | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Movable zone start for each node | ||
| + | [ 0.000000] Early memory node ranges | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] | ||
| + | [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 | ||
| + | bytes. | ||
| + | [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, | ||
| + | linesize 32 bytes | ||
| + | [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. | ||
| + | Total pages: 16256 | ||
| + | [ 0.000000] Kernel command line: console=ttyS0, | ||
| + | rootfstype=squashfs, | ||
| + | [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) | ||
| + | [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) | ||
| + | [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) | ||
| + | [ 0.000000] Writing ErrCtl register=0003e66e | ||
| + | [ 0.000000] Readback ErrCtl register=0003e66e | ||
| + | [ 0.000000] Memory: 59320K/ | ||
| + | rwdata, 544K rodata, 1940K init, 192K bss, 6216K reserved) | ||
| + | [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, | ||
| + | [ 0.000000] NR_IRQS:256 | ||
| + | [ 0.000000] CPU Clock: 580MHz | ||
| + | [ 0.000000] systick: enable autosleep mode | ||
| + | [ 0.000000] systick: running - mult: 214748, shift: 32 | ||
| + | [ 0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) | ||
| + | [ 0.070000] pid_max: default: 32768 minimum: 301 | ||
| + | [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) | ||
| + | [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 | ||
| + | bytes) | ||
| + | [ 0.090000] pinctrl core: initialized pinctrl subsystem | ||
| + | [ 0.100000] NET: Registered protocol family 16 | ||
| + | [ 0.120000] rt2880_gpio 10000600.gpio: | ||
| + | [ 0.130000] rt2880_gpio 10000600.gpio: | ||
| + | [ 0.140000] rt2880_gpio 10000638.gpio: | ||
| + | [ 0.150000] rt2880_gpio 10000638.gpio: | ||
| + | [ 0.160000] rt2880_gpio 10000660.gpio: | ||
| + | [ 0.170000] rt2880_gpio 10000660.gpio: | ||
| + | [ 0.180000] rt2880_gpio 10000688.gpio: | ||
| + | [ 0.190000] rt2880_gpio 10000688.gpio: | ||
| + | [ 0.200000] Switched to clocksource systick | ||
| + | [ 0.210000] NET: Registered protocol family 2 | ||
| + | [ 0.210000] TCP established hash table entries: 1024 (order: 0, 4096 | ||
| + | bytes) | ||
| + | [ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) | ||
| + | [ 0.240000] TCP: Hash tables configured (established 1024 bind 1024) | ||
| + | [ 0.250000] TCP: reno registered | ||
| + | [ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes) | ||
| + | [ 0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | ||
| + | [ 0.280000] NET: Registered protocol family 1 | ||
| + | [ 2.950000] rt-timer 10000100.timer: | ||
| + | [ 2.970000] futex hash table entries: 256 (order: -1, 3072 bytes) | ||
| + | [ 2.990000] squashfs: version 4.0 (2009/ | ||
| + | [ 3.000000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) | ||
| + | (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | ||
| + | [ 3.030000] msgmni has been set to 115 | ||
| + | [ 3.040000] io scheduler noop registered | ||
| + | [ 3.040000] io scheduler deadline registered (default) | ||
| + | [ 3.060000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled | ||
| + | [ 3.070000] console [ttyS0] disabled | ||
| + | [ 3.080000] 10000c00.uartlite: | ||
| + | base_baud = 2500000) is a 16550A | ||
| + | [ 3.090000] console [ttyS0] enabled | ||
| + | [ 3.090000] console [ttyS0] enabled | ||
| + | [ 3.110000] bootconsole [early0] disabled | ||
| + | [ 3.110000] bootconsole [early0] disabled | ||
| + | [ 3.130000] m25p80 spi32766.0: found w25q32, expected gd25q32 | ||
| + | [ 3.140000] m25p80 spi32766.0: w25q32 (4096 Kbytes) | ||
| + | [ 3.150000] 5 ofpart partitions found on MTD device spi32766.0 | ||
| + | [ 3.160000] Creating 5 MTD partitions on " | ||
| + | [ 3.170000] 0x000000000000-0x000000030000 : " | ||
| + | [ 3.180000] 0x000000030000-0x000000040000 : " | ||
| + | [ 3.200000] 0x000000040000-0x000000050000 : " | ||
| + | [ 3.210000] 0x000000050000-0x0000003f0000 : " | ||
| + | [ 3.250000] 0x0000003f0000-0x000000400000 : " | ||
| + | [ 3.260000] ralink_soc_eth 10100000.ethernet: | ||
| + | [ 3.280000] ralink_soc_eth 10100000.ethernet eth0: ralink at | ||
| + | 0xb0100000, irq 5 | ||
| + | [ 3.290000] rt2880_wdt 10000120.watchdog: | ||
| + | [ 3.300000] TCP: cubic registered | ||
| + | [ 3.310000] NET: Registered protocol family 10 | ||
| + | [ 3.320000] NET: Registered protocol family 17 | ||
| + | [ 3.330000] bridge: automatic filtering via arp/ | ||
| + | deprecated. Update your scripts to load br_netfilter if you need this. | ||
| + | [ 3.360000] 8021q: 802.1Q VLAN Support v1.8 | ||
| + | [ 3.380000] Freeing unused kernel memory: 1940K (8035b000 - 80540000) | ||
| + | [ 3.400000] init: Console is alive | ||
| + | [ 3.410000] init: - watchdog - | ||
| + | [ 3.440000] usbcore: registered new interface driver usbfs | ||
| + | [ 3.450000] usbcore: registered new interface driver hub | ||
| + | [ 3.460000] usbcore: registered new device driver usb | ||
| + | [ 3.480000] ehci_hcd: USB 2.0 ' | ||
| + | [ 3.490000] ehci-platform: | ||
| + | [ 3.700000] phy phy-usbphy.0: | ||
| + | [ 3.710000] phy phy-usbphy.0: | ||
| + | [ 3.720000] ehci-platform 101c0000.ehci: | ||
| + | [ 3.730000] ehci-platform 101c0000.ehci: | ||
| + | assigned bus number 1 | ||
| + | [ 3.750000] ehci-platform 101c0000.ehci: | ||
| + | [ 3.780000] ehci-platform 101c0000.ehci: | ||
| + | [ 3.790000] hub 1-0:1.0: USB hub found | ||
| + | [ 3.800000] hub 1-0:1.0: 1 port detected | ||
| + | [ 3.810000] ohci_hcd: USB 1.1 ' | ||
| + | [ 3.820000] ohci-platform: | ||
| + | [ 3.830000] ohci-platform 101c1000.ohci: | ||
| + | [ 3.850000] ohci-platform 101c1000.ohci: | ||
| + | assigned bus number 2 | ||
| + | [ 3.860000] ohci-platform 101c1000.ohci: | ||
| + | [ 3.930000] hub 2-0:1.0: USB hub found | ||
| + | [ 3.940000] hub 2-0:1.0: 1 port detected | ||
| + | [ 4.420000] init: - preinit - | ||
| + | [ 4.520000] 8021q: adding VLAN 0 to HW filter on device eth0 | ||
| + | Press the [f] key and hit [enter] to enter failsafe mode | ||
| + | Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | ||
| + | [ 7.690000] procd: - early - | ||
| + | [ 7.700000] procd: - watchdog - | ||
| + | [ 8.270000] procd: - ubus - | ||
| + | [ 9.280000] random: ubusd urandom read with 14 bits of entropy available | ||
| + | [ 9.300000] procd: - init - | ||
| + | Please press Enter to activate this console. | ||
| + | [ 9.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team | ||
| + | [ 9.900000] Loading modules backported from Linux version | ||
| + | master-2015-07-21-0-g47cd203 | ||
| + | [ 9.920000] Backport generated by backports.git | ||
| + | backports-20150626-0-gc1a4168 | ||
| + | [ 9.950000] cfg80211: World regulatory domain updated: | ||
| + | [ 9.960000] cfg80211: | ||
| + | [ 9.970000] cfg80211: | ||
| + | (max_antenna_gain, | ||
| + | [ 9.990000] cfg80211: | ||
| + | (N/A, 2000 mBm), (N/A) | ||
| + | [ | ||
| + | (N/A, 2000 mBm), (N/A) | ||
| + | [ | ||
| + | (N/A, 2000 mBm), (N/A) | ||
| + | [ | ||
| + | 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) | ||
| + | [ | ||
| + | 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) | ||
| + | [ | ||
| + | (N/A, 2000 mBm), (0 s) | ||
| + | [ | ||
| + | (N/A, 2000 mBm), (N/A) | ||
| + | [ | ||
| + | (N/A, 0 mBm), (N/A) | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | rev 0500 detected | ||
| + | [ | ||
| + | detected | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | |||
| + | |||
| + | |||
| + | BusyBox v1.23.2 (2015-10-23 04:36:59 CEST) built-in shell (ash) | ||
| + | |||
| + | _______ | ||
| + | | ||
| + | | ||
| + | | ||
| + | |__| W I R E L E S S F R E E D O M | ||
| + | | ||
| + | | ||
| + | | ||
| + | * 2 oz. Orange Juice | ||
| + | * 2 oz. Pineapple Juice tall glass filled with | ||
| + | * 2 oz. Grapefruit Juice ice, stir well. | ||
| + | * 2 oz. Cranberry Juice | ||
| + | | ||
| + | root@OpenWrt:/# | ||
| + | root@OpenWrt:/# | ||
| + | * | ||
| + | v7t4g301 | ||
| + | Tenda 4G301 | ||
| + | root@OpenWrt:/# | ||
| + | |||
| + | | ||
| + | </ | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||